Document 6221100-02, ver. 2, rel. 0 march 1999 1 atl p1000 series library unpacking instructions 0 introduction....................................................................................................3 selecting an installation location .......................................................
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 2 adjusting the slide assembly ............................................................ 17 adjusting the slide assembly on the mounting brackets ....... 17 adjusting the slide assembly tray on the slid...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 introduction 3 introduction 0 the atl p1000 series is an automated tape library consisting of up to 4 tape drives and 30 dlt™ cartridges. This document explains how to unpack the atl p1000 series. Once the...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 4 introduction figure 2 atl p1000 series library, rack-mount configuration key lock bulk pack door power switch gui load port load pack door rack (not included).
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 selecting an installation location 5 selecting an installation location 2 when selecting an installation site for the atl p1000 series, consider the following requirements: ‡ floor space ‡ floor clearance ...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 6 selecting an installation location figure 4 shows the floor space requirements for the rack-mount p1000. Figure 4 floor space requirements, rack-mount library floor clearance 4 the stand-alone p1000 has ...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 selecting an installation location 7 power inlet 4 the power inlet is an iec-320 connector (see figure 5). For international applications, replace the power cord with a harmonized 3 x 1.0 mm 2 power cord a...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 8 unpacking the library unpacking the library 5 the p1000 unpacking procedure consists of the following steps: ‡ receiving the library from the shipper (see “unloading space requirements” on page 9) ‡ uncr...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 unloading space requirements 9 unloading space requirements 5 before uncrating the library, verify that you have sufficient space. For the stand-alone unit, allow a minimum of six feet in front of the ramp...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 10 uncrating the library uncrating the library 6 to uncrate the p1000 library: procedure 1 open the top of the shipping carton by carefully cutting the packaging tape. The following items are stacked on to...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 uncrating the library 11 figure 7 uncrating the stand-alone library accessories tray ramp foam supports library clips.
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 12 uncrating the library figure 8 uncrating the rack-mount library procedure (continued) 4 release the four clips that secure the carton to the pallet. To release a clip, pinch the center tabs of the clip ...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 installing the slide assembly in the rack 13 installing the slide assembly in the rack 8 if you are installing a rack-mount library, install the slide assembly in the rack before proceeding to “removing th...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 14 installing the slide assembly in the rack grounding 8 the p1000 must be connected to a grounded power outlet. If the library is rack-mounted, the rack must also be grounded. Temperature 8 the rack tempe...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 installing the slide assembly in the rack 15 procedure (continued) 2 if the rack retma rail holes are not threaded, attach the appropriate threaded clips to the holes that correspond to: ‡ the mounting bra...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 16 installing the slide assembly in the rack procedure (continued) 7 remove the two 10-32 x 3/4 in. Temporary support screws from the front retma rails and install them in the left and right rear mounting ...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 installing the slide assembly in the rack 17 adjusting the slide assembly 10 now that the slide assembly is installed in the rack, verify that: ‡ the front door of the rack opens and closes freely. ‡ the r...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 18 installing the slide assembly in the rack procedure (continued) 3 when the slide assembly is in the desired position, tighten all outer nuts: a pull the slide assembly tray forward until you can access ...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 installing the slide assembly in the rack 19 figure 12 slide assembly tray, fully extended adjusting the slide assembly tray on the slide rails 12 to adjust the slide assembly tray on the slide rails: proc...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 20 installing the slide assembly in the rack figure 13 loosening the inner nuts procedure (continued) 3 when the slide assembly tray is in the desired position, tighten all inner nuts: a extend the slide a...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 installing the slide assembly in the rack 21 procedure (continued) e use a phillips screwdriver to tighten the screw while holding its corresponding nut with an 11/32 inch open-ended wrench. F repeat steps...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 22 removing the library from the pallet removing the library from the pallet 13 this section provides separate procedures for the stand-alone and rack-mount libraries: ‡ to remove a stand-alone library fro...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 removing the library from the pallet 23 figure 14 removing the foam supports, stand-alone library procedure (continued) 3 attach the ramp to the pallet using fastener strips (see figure 15). 4 make any nec...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 24 removing the library from the pallet procedure (continued) 7 roll the library to the installation site. 8 save the shipping carton, bag, foam supports, ramp, and pallet for future use. These items are r...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 removing the library from the pallet 25 procedure (continued) 3 with the help of a second person, lift the library from the pallet (see figure 16). Figure 16 lifting the rack-mount library from the pallet ...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 26 removing the library from the pallet procedure (continued) 4 place the library on the fully extended slide assembly tray (see figure 17). Figure 17 placing the library on the slide assembly tray 5 secur...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 removing the library from the pallet 27 procedure (continued) 8 to prevent the library from sliding out of the rack during operation, secure the locking brackets to the retma rails (see figure 18). Figure ...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 28 removing the internal packing materials removing the internal packing materials 18 this section explains how to remove the internal packing materials that protect the library during shipping and install...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 removing the internal packing materials 29 figure 19 removing the load and bulk packs removing the shipping restraint 19 to remove the shipping restraint: note: the shipping restraint that protects the ext...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 30 removing the internal packing materials figure 20 removing the shipping restraint extension axis assembly drive shelf shipping restraint.
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 packaging the library for reshipment 31 packaging the library for reshipment 20 if it becomes necessary to reship the library, repackage the library in its original shipping materials as follows: procedure...
Atl p1000 series library unpacking instructions document 6221100-02, ver. 2, rel. 0 march 1999 32 packaging the library for reshipment procedure (continued) c carefully lower the extension axis assembly so that it rests on the foam block. D hook the lip of the shipping restraint under the edge of th...
