1. DL manuals
  2. Quantum
  3. Two-Way Radio
  4. QP-750
  5. User Manual

Quantum QP-750 User Manual - Thank You

Summary of QP-750

  • Page 1

    7120710000 qp-750 user manual quantun electronics, llc.

  • Page 2: Thank You

    1 thank you thank you for your purchase of the quantun two-way portable radio. This easy-to-use radio adopts the latest advanced technology, providing reliable communication performance in today’s demanding communications environment. Before operating this radio, please read this manual carefully to...

  • Page 3

    2 contents user safety, training, and general information compliance with rf energy exposure standards operational instructions and training guidelines fcc compliance precautions care and cleaning supplied accessories radio overview parts of the radio table below explains the functions of the leds a...

  • Page 4

    3 user safety, training, and general information read this important information on safe and efficient operation before using your quantun portable two-way radio. Compliance with rf energy exposure standards your quantun two-way radio is designed and tested to comply with a number of national and in...

  • Page 5

    4 operational instructions and training guidelines to ensure optimal performance and compliance with the occupational/controlled environment rf energy exposure limits in the above standards and guidelines, users should transmit no more than 50% of the time and always adhere to the following procedur...

  • Page 6

    5 fcc compliance this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use...

  • Page 7

    6 z do not modify or adjust this transceiver without permission. Z do not expose the transceiver to direct sunlight over a long time nor place it close to heating source. Z do not place the transceiver in excessively dusty, humid areas, or on unstable surfaces. Safety: it is important that the opera...

  • Page 8

    7 radio overview parts of the radio 1 2 3 6 5 4 7 8 10 9 11 12 15 14 13 16 figure 1 1. Ptt key 2. Sfk1 (programmable side key 1) 3. Sfk2 (programmable side key 2) 4. Antenna 5. Microphone 6. Speaker 7. Tfk (programmable top key) 8. Channel selector knob.

  • Page 9

    8 9. Led indicator ( details as following table) 10. Radio on-off/volume control knob 11. Accessory jack 12. Battery latch 13. Belt clip 14. Accessory cover 15. Battery 16. Charge terminal the functions of the leds and beeps table power on the green led flashes once, and radio beeps ( if programmed ...

  • Page 10

    9 programmable auxiliary functions your dealer may program the tfk, sfk1, sfk2 (long or short press) keys with one of the following auxiliary functions respectively. Z auto contact z auto contact temporary delete z battery power indicator z callⅠ/callⅡ dtmf 2tone mdc1200 safety check z channel annun...

  • Page 11

    10 z squelch off z squelch off momentary z s 2 double saving mode z talk around z vox z vox backup z whisper z whisper backup signaling feature 1) mdc 1200 signaling: z selective call decode z call alert decode z radio check decode z selective radio inhibit decode z selective radio inhibit cancel de...

  • Page 12

    11 getting started battery safety precautions the battery is not charged at the factory. It is recommended to charge the new battery before using it. Also, batteries that may have set longer than 2 months since the last charge should be charged before using it. Please charge it for 12 hours, which a...

  • Page 13

    12 1. Considering the battery's self-discharge characteristics, fully charge the battery prior to long time storage, to avoid battery damage due to over-discharge. 2. Recharge the battery after 6 months’ storage, to avoid reducing battery capacity due to over-discharge. 3. Notice the ambient humidit...

  • Page 14

    13 antenna stubby antennas are ideal for communication within limited range. Fine and long antennas optimizes communication coverage, ideal when the radio is worn on the belt because they are flexible and soft. Rainy days or forest locations may narrow your communication range, please repare in adva...

  • Page 15

    14 fig. 4 1. Turn off the radio if it is turned on. 2. Disengage by pushing downward and holding the latch towards the front of the radio. 3. With the battery latch disengaged, slide the battery down from the top of the radio about 12mm. Once the battery is free from the battery rails, lift it direc...

  • Page 16

    15 fig. 5 belt clip attaching belt clip: align the slot of the belt clip with the t-slot on the battery cover and press the belt clip downwards until it is locked. Fig. 6 removing the belt clip: press the disassembly release outwards with a key until it releases and then push the belt clip upwards w...

  • Page 17

    16 fig.7 attaching the earpiece/microphone open (not remove) the accessory cover, plug the audio accessory firmly into the accessory jack. Note: using the radio with audio accessory may affect the waterproof performance of the radio. Fig. 8.

  • Page 18

    17 basic operations turn on/off the radio to turn the radio on, rotate the “power/volume” knob clockwise. An alert tone indicates that the self-test of the radio completed successfully. The led glows green during power-up. If self-test fails and/or the selected channel is not set, you will also hear...

  • Page 19

    18 is enabled. Please contact your dealer for more details. Vox operation when hands-free operation is desired, your radio can be activated by voice alone using the vox feature when you speak through an accessory that is connected to your radio. Z connecting a vox headset 1. Turn off your radio. 2. ...

  • Page 20

    19 advanced operations the following functions are programmable by your dealer. These functions are for professional users. Auto contact when a group of radios are set with auto contact, the radio will automatically emit alert tone if the user is out of communication range. Auto contact temporary de...

  • Page 21

    20 radio receives an incoming signal that with match 2-tone/mdc1200. ● red led solidly glows while encoding; orange led solidly glows until the preset time expires after encoding ends. ●green led solidly glows while decoding; orange led flashes until the preset time expires after successfully decode...

  • Page 22

    21 on radio, the current channel number will not be heard. Please select the volume level as "1", when using an earpiece. Channel lock press the programmed function key to activate the channel lock mode, when the channel lock feature is activated, rotate the channel selector is invalid. Emergency pr...

  • Page 23

    22 the man down status will not be memorized once radio power off. Man down backup (optional) press the programmed function key to activate the man down mode, horizontally or inversely position the radio will activate an alert tone, a defined emergency procedure is activated if the radio is horizont...

  • Page 24

    23 press the scan key again to exit radio scanning. The scan status will not be memorized once radio power off. Z nuisance channel temporary delete „ when scan pauses on an unwanted channel such as a noise channel, press the programmed nuisance channel temporary delete key to temporarily delete the ...

  • Page 25

    24 squelch level set on the current channel. S 2 double saving tm mode press the programmed s 2 double saving mode key, if one beep is heard, the s 2 double saving mode is enabled. If two beeps are heard, the s2 double saving mode is disabled. When s 2 double saving mode is enabled, the battery will...

  • Page 26

    25 intrinsically programmable operations the feature allows for more efficient use of the radio, those functions need to be programmed by your dealer. Ctcss/cdcss if ctcss/cdcss is set on the current channel, causes a ctcss/cdcss match to be required on an incoming signal for radio to unmute. The ra...

  • Page 27

    26 when the bcl feature is enabled, you are prevented from transmitting on a channel that is already in use. Press the ptt on a channel that is already in use, the radio will sound alert tone and turn back to the receive mode. Carrier: if bcl is set on the current channel, press the ptt while the ch...

  • Page 28

    27 must have this feature activated. Vox when hands-free operation is desired, your radio can be activated by voice alone using the vox feature when you speak through an accessory that is connected to your radio. Enabling or disabling vox operation, press the preprogrammed vox button. Note: pressing...

  • Page 29

    28 service if you need service, contact your quantun dealer. If you find it inconvenient to have service performed by your local dealer, you may contact quantun below: quantun electronics,llc 1379 shotgun road sunrise, florida 33326 usa main line: 954-598-3500 toll free usa: 888-361-0521 www.Quantun...