Summary of Q6 Edge HD
Page 2
Warning! A quantum rehab provider or a qualified technician must perform the initial setup of this power chair and must perform all of the procedures in this manual. The symbols below are used throughout this owner’s manual and on the power chair to identify warnings and important information. It is...
Page 3
Q6 series 3 i. Introduction .................................................................................................................................. 4 ii. Safety ...................................................................................................................................
Page 4
4 q6 series i . I n t r o d u c t i o n safety welcome to quantum rehab, a division of pride mobility products (pride). The power chair you have pur- chased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident that these design features will provide you wi...
Page 5
Q6 series 5 read and follow the information in the owner’s manual. I i . S a f e t y product safety symbols the symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. Note: there ...
Page 6
Q6 series 6 general guidelines mandatory! Do not operate your new power chair for the first time without completely reading and understanding this owner’s manual. Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive variety of prod...
Page 7
Q6 series 7 manual freewheel lever drive wheel i i i . Y o u r p o w e r c h a i r the q6 series power chair your power chair has two main assemblies: the seat assembly and the power base assembly. See figure 1. Typically, the seat assembly includes the armrests, seatback, and seat base. The power b...
Page 8
8 q6 series manual freewheel lever i i i . Y o u r p o w e r c h a i r electrical components the electrical components consist of the controller assembly, the batteries, and the motors. The batteries, motors, and controller power module (if equipped) are located on the power base assembly. The contr...
Page 9
Q6 series 9 to motor connector to motor connector to battery connectors main circuit breaker quick release battery connectors i i i . Y o u r p o w e r c h a i r main circuit breaker (located on the rear main frame): the main circuit breaker is a safety feature built into your power chair. When the ...
Page 10
10 q6 series manual freewheel lever manual freewheel lever i i i . Y o u r p o w e r c h a i r manual freewheel levers for your convenience, your power chair is equipped with a manual freewheel lever mounted on each motor. The levers allow you to disengage the drive motors and maneuver the chair man...
Page 11
Q6 series 11 initial assembly your power chair may require some assembly either before initial use or after transportation. It may also require disassembly to make some comfort adjustments. Figure 6 details those parts of the power chair that are designed to be disassembled and assembled by an end u...
Page 12
12 q6 series i v . A s s e m b l y figure 7. Universal mounting system and contour seat rear extrusion front extrusion seat installation it may be necessary to install the seat either prior to initial operation or after transporting your power chair. Contour seats are attached to the power base with...
Page 13
Q6 series 13 i v . A s s e m b l y figure 10. Transit securement brackets figure 9. Controller harness routing on a contour seat wire ties to power base transit securement system if your power chair is equipped with a transit securement system, it is equipped with manufacturer- installed front and r...
Page 14
14 q6 series i v . A s s e m b l y figure 11. Unoccupied transit system securement points front of vehicle.
Page 15
Q6 series 15 you may need the following to make comfort adjustments: metric/standard socket set and ratchet adjustable wrench metric/standard hex key set thread lock seat height and seat angle adjustment if your power chair is not equipped with a transit securement system, you can change the...
Page 16
16 q6 series figure 13. Seat position adjustment v . C o m f o r t a d j u s t m e n t s seat mounting holes 7. Remove the hardware that attaches the trapeze bars to the seat interface weldments. See figure 12. 8. Move the trapeze bars up or down to the desired height. Note: change the seat dump by ...
Page 17
Q6 series 17 v . C o m f o r t a d j u s t m e n t s seatback angle adjustment if your power chair is equipped with an adjustable seat- back, you can adjust it to four (4) different angles: 90°, 102°, 105°, or 107°. To adjust the seatback angle: 1. Remove the adjusting screws from each seat hinge. S...
Page 18
18 q6 series v . C o m f o r t a d j u s t m e n t s figure 15. Underside of armrest controller position you can move the controller in toward or out away from the armrest, or change the position of the control- ler for either left-hand or right-hand use. Warning! Do not place the controller harness...
Page 19
Q6 series 19 foot platform bracket hardware screw v . C o m f o r t a d j u s t m e n t s foot platform height adjustment the foot platform height is easily adjusted to several different heights. To raise or lower the foot platform: 1. Remove the hardware from the foot platform bracket. See figure 1...
Page 20
20 q6 series to adjust the positioning belt for operator comfort: 1. Once seated, insert the metal tab on one side of the belt into the plastic housing on the opposite side until you hear a click. See figure 17. 2. Pull the excess strap attached to the metal tab until it is secure, but not so tight ...
Page 21
Q6 series 21 v i . B a t t e r i e s a n d c h a r g i n g batteries and charging the q6 series uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries ...
Page 22
22 q6 series v i . B a t t e r i e s a n d c h a r g i n g battery break-in to break in new batteries for maximum efficiency: 1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance level. 2. Operate your power chair throughout the ...
Page 23
Q6 series 23 daily use if you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power chair. Your power chair will be ready each morning to give you a full day’s service. It is recommended that you charge the batteries 8 to 14 hours after daily use....
Page 24
24 q6 series v i . B a t t e r i e s a n d c h a r g i n g how can i ensure maximum battery life? A fully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your power chair’s batteries fully charged whenever possible. Batteries that are regularly and deeply...
Page 25
Q6 series 25 care and maintenance your q6 series is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks. You can perform some of these checks, but others require assistance from your quantum rehab provider. Preven- tive maintenance is very important. If yo...
Page 26
26 q6 series the body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain its high-gloss appearance. check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery tray, with th...
Page 27
Q6 series 27 storage your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries from the power chair. See vi. “batteries and charging.” warning! If you fail to store the unit properly, the frame can rust and the electronics can be damaged...
Page 28
28 q6 series v i i . C a r e a n d m a i n t e n a n c e follow these easy steps for a quick and safe repair for both pneumatic and solid tires: 1. Turn off the power to the controller. 2. Set the power chair up on blocks. 3. If you are changing a pneumatic tire, completely deflate it before removin...
Page 29
Q6 series 29 rear battery quick release battery connectors v i i . C a r e a n d m a i n t e n a n c e figure 21. Battery installation battery wiring diagram label front cover to replace the batteries: 1. Turn off the power to the controller. 2. Make sure that the power chair is in drive mode. See i...
Page 30
30 q6 series v i i . C a r e a n d m a i n t e n a n c e when to see your quantum rehab provider for service the following symptoms could indicate a serious problem with your power chair. If necessary, contact your quantum rehab provider. When calling, have the model number, serial number, nature of...