1. DL manuals
  2. Quantum
  3. Storage
  4. ValueLoader DLT VS80
  5. Product Specification

Quantum ValueLoader DLT VS80 Product Specification - 6.2

Manual is about: Quantum DLT 1: User Guide

Summary of ValueLoader DLT VS80

  • Page 2

    Ii may 2004 001597-01 rev. A09 copyright copyright © 2004 by quantum corporation. All rights reserved. Document origination: boulder, colorado, usa. Trademarks quantum, the quantum logo, and the dlttape logo are trademarks of quantum corporation registered in the u.S.A. And other countries. Dlttape,...

  • Page 3

    001597-01 rev. A09 may 2004 iii the support section of the web site lists telephone numbers, street addresses, time zones, and other pertinent facts. Revision history all revisions made to this document are listed below in chronological order. User manual statements for class a equipment (internal t...

  • Page 4

    Iv may 2004 001597-01 rev. A09 • part 2 - electrostatic discharge (esd) requirements • part 3 - radiated electromagnetic field requirements • part 4 - electrical fast transient/burst (eft) requirements • part 5 - surge requirements • part 6 - conducted disturbances, induced by radio-frequency fields...

  • Page 5

    001597-01 rev. A09 may 2004 v the user may find the following booklet prepared by the federal communications commission helpful: how to identify and resolve radio-tv interference problems. This booklet is available from the u.S. Government printing office, washington d.C., 20402. Stock no. 004-00398...

  • Page 6

    Vi may 2004 001597-01 rev. A09 vcci class b ite regulatory mark.

  • Page 7: Table Of Contents

    001597-01 rev. A09 may 2004 vii table of contents ce notice (european union) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-iii fcc notices (u.S. Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 8

    Table of contents viii may 2004 001597-01 rev. A09 5 environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 temperature and humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 altitude . . . . . . ...

  • Page 9

    Dlt vs80 product specification 001597-01 rev. A09 may 2004 ix 10 reliability factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 11 dlttape iv recording media specifications . . . . . . . . . . . . . 11-1.

  • Page 10

    Table of contents x may 2004 001597-01 rev. A09 notes.

  • Page 11: List Of Figures

    001597-01 rev. A09 may 2004 xi list of figures 2 physical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 figure 2-1. Mounting holes and dimensions (bottom view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 figure 2-2. Mounting holes and dimensions ...

  • Page 12

    List of figures xii may 2004 001597-01 rev. A09 notes.

  • Page 13: List of Tables

    001597-01 rev. A09 may 2004 xv list of tables 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 table 1-1. Chapters in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 2 physical specifica...

  • Page 14

    List of tables xvi may 2004 001597-01 rev. A09 table 6-5. Non-operating shock (drop) specifications (packaged tape drive) . . . . . . . . . . . . . . . 6-3 table 6-6. Non-operating shock “overstress” (bench handling) specifications (unpackaged tape drive) . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 15: Introduction

    001597-01 rev. A09 may 2004 1-1 c hapter 1 chapter 1 introduction this chapter describes the purpose, scope, and audience of this manual. It also lists related documentation. 1.1 purpose and scope this document describes the dlt vs80 tape drive, listing its physical and functional characteristics an...

  • Page 16: 1.2

    Chapter 1: introduction 1-2 may 2004 001597-01 rev. A09 this document does not include installation and operation information. 1.2 audience the primary audience for this document consists of engineers and technicians interested in integrating the dlt vs80 tape drive into computer systems and other e...

  • Page 17: 1.4

    Dlt vs80 product specification 001597-01 rev. A09 may 2004 1-3 1.4 conventions used in this manual this manual uses the following conventions: n ote : notes provide supplemental information. T ech t ip : tech tips provide information that helps you complete a procedure or avoid additional steps. C a...

  • Page 18

    Chapter 1: introduction 1-4 may 2004 001597-01 rev. A09 notes.

  • Page 19: Physical Specification

    001597-01 rev. A09 may 2004 2-1 c hapter 2 chapter 2 physical specification this chapter presents the physical characteristics of the dlt vs80 subsystem: internal and external size, electrical requirements, communication interface, and mean time between failures (mtbf). This chapter also shows mount...

  • Page 20

    Chapter 2: physical specification 2-2 may 2004 001597-01 rev. A09 table 2-2 lists each tape drive unit’s electrical requirements and power consumption. 1 voltage measured at the power bus connector pins. 2 maximum current values are for approximately 300ms durations. Table 2-3 shows the communicatio...

  • Page 21: 2.2

    Dlt vs80 product specification 001597-01 rev. A09 may 2004 2-3 2.2 tape drive dimensions and mounting hole locations the internal tape drive provides standard mounting holes. The following sections present the tape drive dimensions and mounting hole locations. 2.2.1 mounting holes (bottom view) figu...

  • Page 22

    Chapter 2: physical specification 2-4 may 2004 001597-01 rev. A09 2.2.2 mounting holes (side view) figure 4-1 shows the mounting holes and dimensions as viewed from the side of the tape drive. Figure 2-2. Mounting holes and dimensions (side view) n otes : 1 tape drive width and length are standard 5...

  • Page 23: Functional Specifications

    001597-01 rev. A09 may 2004 3-1 c hapter 3 chapter 3 functional specifications this chapter describes the functional specifications for this tape drive. It also lists the light emitting diodes (leds) on the tape drive front bezel, describes each led state (on, off, blinking, and so forth), and descr...

  • Page 24: 3.2

    Chapter 3: functional specifications 3-2 may 2004 001597-01 rev. A09 1 compressed values use a nominal 2:1 compression ratio. Actual compression is data-dependent. 3.2 leds the dlt vs80 has 3 leds with the following functions: transfer rate native 3.0 mb/s compressed 1 up to 6.0 mb/s burst 16 mb/s e...

  • Page 25

    Dlt vs80 product specification 001597-01 rev. A09 may 2004 3-3 clean/media led (amber) blinking a hard read/write error has occurred that is probably recoverable. Clean the drive. Led is off after completing a cleaning cycle with a dtl1 cleaning cartridge or after loading a properly formatted data c...

  • Page 26

    Chapter 3: functional specifications 3-4 may 2004 001597-01 rev. A09 notes.

  • Page 27: Performance Specifications

    001597-01 rev. A09 may 2004 4-1 c hapter 4 chapter 4 performance specifications this chapter describes performance specifications, including tape speed and time to perform rewind, access, load, and unload operations. 4.1 timing characteristics table 4-1 lists speed and timing characteristics of the ...

  • Page 28

    Chapter 4: performance specifications 4-2 may 2004 001597-01 rev. A09 notes.

  • Page 29: Environmental Specifications

    001597-01 rev. A09 may 2004 5-1 c hapter 5 chapter 5 environmental specifications this section describes environmental specifications: • temperature and humidity • altitude. The dlt vs80 tape drive conforms to an environment that includes general offices and workspaces with the following conditions:...

  • Page 30: 5.1

    Chapter 5: environmental specifications 5-2 may 2004 001597-01 rev. A09 5.1 temperature and humidity table 5-1 lists the operating temperature and humidity ranges. Table 5-2 lists the temperature and humidity ranges for storing and shipping the tape drive. If you have stored or shipped the tape driv...

  • Page 31: Shock and Vibration

    001597-01 rev. A09 may 2004 6-1 c hapter 6 chapter 6 shock and vibration specifications this chapter describes operating and non-operating shock and vibration specifications. 6.1 operating shock and vibration table 6-1 lists operating vibration specifications, and table 6-2 on page 6-2 lists operati...

  • Page 32: 6.2

    Chapter 6: shock and vibration specifications 6-2 may 2004 001597-01 rev. A09 6.2 non-operating shock and vibration table 6-3 , table 6-4 , and table 6-5 list non-operating vibration and non-operating shock specifications for the dlt vs80 tape drive inside its shipping package. Table 6-2. Operating ...

  • Page 33

    Dlt vs80 product specification 001597-01 rev. A09 may 2004 6-3 table 6-6 , table 6-7 on page 6-4 , and table 6-8 on page 6-4 list non-operating vibration and non- operating shock specifications for the dlt vs80 tape drive outside its shipping package. Table 6-4. Non-operating repetitive shock specif...

  • Page 34

    Chapter 6: shock and vibration specifications 6-4 may 2004 001597-01 rev. A09 table 6-7. Non-operating vibration specifications (unpackaged tape drive) parameter sine value sweep value vibration type sine sweep frequency range 10 to 500 to 10 hz upward and downward sweep acceleration level 1 g 10 to...

  • Page 35: 7.1

    001597-01 rev. A09 may 2004 7-1 c hapter 7 chapter 7 electromagnetic compatibility this chapter describes electromagnetic compatibility (emc) specifications, including the following topics: • emissions radiated emissions conducted emissions harmonic current emissions • immunities electrostatic disch...

  • Page 36: 7.1.1  Radiated Emissions

    Chapter 7: electromagnetic compatibility 7-2 may 2004 001597-01 rev. A09 7.1.1 radiated emissions class b equipment must meet limits of radiated interference field strength, in the frequency range from 30 mhz to 1000 mhz at a test distance of 10 meters. Table 7-1 lists the cispr 22: 1997 radiated em...

  • Page 37: 7.2

    Dlt vs80 product specification 001597-01 rev. A09 may 2004 7-3 7.2 harmonic current emissions the dlt vs80 tape drive meets or exceeds the harmonic current emissions requirements in en 61000-3-2: 1995. Table 7-3 lists the en 61000-3-2:1995 fluctuating harmonics limits for harmonic current emissions ...

  • Page 38: 7.3

    Chapter 7: electromagnetic compatibility 7-4 may 2004 001597-01 rev. A09 7.3 immunities the dlt vs80 tape drive meets or exceeds the electromagnetic immunity limits required in the following specifications: • emc directive (89/336/eec) • en55024: 1998 information technology equipment - immunity • ci...

  • Page 39: 7.3.4  Surge Immunity

    Dlt vs80 product specification 001597-01 rev. A09 may 2004 7-5 7.3.3 fast transient immunity table 7-7 lists the en 61000-4-4:1995 fast transient immunity limits. 7.3.4 surge immunity table 7-8 lists the en 61000-4-5:1995 surge immunity limits. 7.3.5 conducted immunity table 7-9 lists the en 61000-4...

  • Page 40: Immunity

    Chapter 7: electromagnetic compatibility 7-6 may 2004 001597-01 rev. A09 7.3.7 voltage dips, short interruptions and variations immunity table 7-11 lists the en 61000-4-11:1994 ac dips, interruptions, and variations immunity limits. 7.4 voltage fluctuations and flicker the dlt vs80 tape drive meets ...

  • Page 41: Safety Specifications

    001597-01 rev. A09 may 2004 8-1 c hapter 8 chapter 8 safety specifications this section describes safety specifications including: • safety standards • cb scheme. 8.1 safety the dlt vs80 tape drive meets or exceeds the safety requirements in the following specifications: • low voltage directive (73/...

  • Page 42

    Chapter 8: safety specifications 8-2 may 2004 001597-01 rev. A09 notes.

  • Page 43: Acoustic Noise Emissions

    001597-01 rev. A09 may 2004 9-1 c hapter 9 chapter 9 acoustic noise emissions this chapter presents the acoustic noise emission levels and the specifications they meet. 9.1 declared levels the dlt vs80 tape drive meets or exceeds the acoustic noise emission level requirements in the following specif...

  • Page 44

    Chapter 9: acoustic noise emissions 9-2 may 2004 001597-01 rev. A09 n ote : current values for specific configurations are available from quantum representatives. Acoustics – declared values per iso 9296 and iso 7779/en27779 product sound power level sound pressure level lwa, b lpam, dba (bystander ...

  • Page 45: Reliability Factors

    001597-01 rev. A09 may 2004 10-1 c hapter 10 chapter 10 reliability factors this chapter presents factors related to the reliability of the tape drive: head life, mean time between failures (mtbf), load/unload cycles, and tape life. Table 10-1 lists the dlt vs80 reliability parameters and values. Ta...

  • Page 46

    Chapter 10: reliability factors 10-2 may 2004 001597-01 rev. A09 notes.

  • Page 47: Dlttape Iv Recording Media

    001597-01 rev. A09 may 2004 11-1 c hapter 11 chapter 11 dlttape iv recording media specifications this chapter lists the media characteristics in table 11-1 : table 11-1. Recording media specifications dlttape™iv media description value width 0.498 inch metal particle length 1828 ft data cartridge d...

  • Page 48

    Chapter 11: dlttape iv recording media specifications 11-2 may 2004 001597-01 rev. A09 notes.

  • Page 50

    4001 discovery dr., ste. 1100 boulder, co 80303 720.406.5700 may 17, 2004 001597-01 rev. A09 *001597-01 a09* 001597-01 rev a09.