1. DL manuals
  2. Quasar
  3. Gateway
  4. SmartCell 112
  5. Installation Manual

Quasar SmartCell 112 Installation Manual

Summary of SmartCell 112

  • Page 1

    Thank you for purchasing “smartcell 212 /112” product. Quasar communication systems ltd. And its distributors assume no responsibility for any damage or loss resulting from the use of its products or this user manual. Quasar communication systems ltd and its distributors assume no responsibility for...

  • Page 3: 1. Introduction

    2 1. Introduction 1.1 overview the smartcell 212 and 112 gateway enables direct connection of an organization's internal telephony system to commercial cellular networks via an already existing private branch exchange (pbx) system. The smartcell 212 has a standard isdn bri “s0” interface on the line...

  • Page 4

    Smartcell 212/112 3 cables power cable isdn interface cable sync in cable antenna 2 bags with screws & dowel pins smartcell 212/112 unit drill template.

  • Page 5: 2. Safety Precautions

    4 2. Safety precautions main voltages are present at specific points in this equipment. Some of the parts can also have high operating temperatures. Non-observance of these conditions and safety instructions can result in personal injury or in property damage. The smartcell 212 system complies with ...

  • Page 6: 3. Product Description

    Smartcell 212/112 5 3. Product description 3.1 technical specifications* power supply supply voltage (secondary) 12v dc supply current 2 a max. Operating temperature 0 ºc to 40 ºc standards full ce isdn specifications line interface bri – s/t point reference (indoor only), type nt or partial te. Pro...

  • Page 7: 3.2 Led Indications

    6 3.2 led indications led description operation power indicates the status of the power connection. On–the smartcell 112/212 is powered on. Off–the smartcell 112/212 is powered off. Status 1 indicates the smartcell 212 operational status of channel 1 off–the channel is idle and no calls are being ha...

  • Page 8

    Smartcell 212/112 7 led description operation status 2 indicates the smartcell 212 operational status of channel 2. Off–the channel is idle and no calls are being handled. On–the channel is handling a call. Slow blinking–the smartcell 112/212 is initialising following power up or is being programmed...

  • Page 9

    8 4. Smartcell 212/112 installation 4.1 installation instructions 4.1.1 locate template on the wall and mark screw location 4.1.2 bore 3 holes..

  • Page 10

    Smartcell 212/112 9 4.1.3 insert 3 dowel pins. 4.1.4 tighten the two upper screws. Leave a gap of 3mm minimum between the screw head and the wall. 4.1.5 mount the smartcell 212/112 on the 2 screws..

  • Page 11

    10 4.1.6 tighten the lower screw. 4.1.7 connect cables. Power cable nt cable sync in cable (only if necessary).

  • Page 12

    Smartcell 212/112 11 4.1.8 connect antennas. Antenna x2 bracket x2.

  • Page 13

    12 4.2 configuration of the pabx the pabx connected to a smartcell device must be properly configured in order to operate. The table below describes the configurations. For more detailed information regarding the programming of the pabx, please contact your pabx supplier. Pbx isdn interface definiti...

  • Page 14: 4.4 Cable Connections

    Smartcell 212/112 13 pabx te 212/112 212/112 4.4 cable connections 4.4.1 normal connection in normal connection, the 212/112 is used as the nt side and the pabx as the te side. The sync (timing) is delivered from the 212/112 to the pabx over the isdn cable. The sync in/te port of the 212/112 is not ...

  • Page 15

    14 4.4.3 external sync mode in this mode, the pabx is used as the te side and the 212/112 is used as the nt side of the isdn connection. However, the sync (timing) is delivered from the pabx to the 212/112 over a second cable (a straight rj-45 cable, provided with 212/112). This cable connects to an...

  • Page 16: 4.5 Getting Started

    Smartcell 212/112 15 4.5 getting started 4.5.1 after making all connections and installing the sim cards, make sure the power led is lit. If it is not, make sure that the power supply is properly connected to the unit and to the ac mains. 4.5.2 during the first few seconds after powering the unit, t...