Quick 3202 lead free soldering station operation manual thank you for purchasing the unit. It is designed for lead free soldering. Please read this manual carefully before use and keep it for future reference..
Ⅺ. Tips 200-2.4d 200- 1.6 d 200-1.2d 2 00- 3.2d 20 0- 4.2d 200 -sb 200-b 0 .5 0 .5 3. 5 45° 1 5 25 ° 4 5 ° 2 1 0 1.5 10 4 r 0. 5 9 2 r 0. 5 2 00- 2c 7 .5 2 12 3 4 5° 1.2 3 .5 200-h 1 0 3.7 200-1c 1 2 3 .5 2 200- 0 .8c 4 5 ° 12 200- k 1 .5 200-sk r 0.2 12 4 5 ° 12 45 ° 1 .5 12 4 5 ° 200-2b 200- 3 c r...
Ⅰ. Safety instruction warning in this instruction manual, “ warning ”“ caution” and “ note” are defined as followings: warning: misuse may potentially cause death or serious injury to the user. Caution: misuse may potentially cause injury to the user or physical damage to the objects involved. For y...
10.1 check the soldering iron 1. Pull out the plug and measure the resistance value between the pins of the connecting plug when the heating element cooling down to the room temperature. 2. If the value of ‘a’ is different from the values in the following table, replace the heating element or cord a...
Ⅱ. Specification power 220v power consumption 90w temperature range 100℃~500℃ (decide by working mode) highest ambient temperature 40℃ temperature stability ±2℃/without air flow and no load tip to ground resistance tip to ground potential heating element electromagnetic heater dimension 96(w)×160(l)...
(2) when the temperature is stable, clean the tip with the cleaning sponge, check the condition of the tip. (3) coat the tip with solder if there is black oxide around it, then clean it with sponge. Repeat until the black oxide is completely removed. Then coat the tip with solder again. This will pr...
(1) use about the clean sponge. dampen the small cleaning sponge with water and then squeeze it dry. place the small sponge in groove of the iron holder base. add a little water to iron holder. The small sponge will absorb water to keep the large sponge around it wet at all times. dampen the...
3. Press the “▲” & “▼” buttons simultaneously, press the “*” button until the lcd displays “cal” to enter the calibrating temperature mode. 4. When the 100’s digit starts to flash, select the value by pressing “▲” or “▼” button according to the reading of the thermometer and then click “*” button to...
4.3.2 temperature setting raise temperature:click “▲” button, the temperature will rise１℃, the lcd will display the current setting temperature. If press the “▲” button for at least 1s, the setting temperature will rise rapidly. Loose the “▲” button when the value is up to the required temperature. ...
2. In the sleeping time setting interface, click “▲” or “▼” button to adjust the sleeping time. The sleeping time setting range is “00~99” or “--” (unit: minute). 00: means when putting the soldering iron handle on the soldering holder, it will come into the sleeping state at once. 01~99: means when...
5.1 input right password 5.1.1 into the parameter setting 1. Turn off the power switch. And then press the “ ▲ ” & “ ▼” buttons simultaneously, afterwards, turn on the power switch. 2. It can loosen the “▲” & “▼” buttons until the screen shows , which means it has come into the parameter setting mod...
