1. DL manuals
  2. Quickie
  3. Wheelchair
  4. Salsa M2
  5. Instructions For Use Manual

Quickie Salsa M2 Instructions For Use Manual

Manual is about: Power wheelchairs

Summary of Salsa M2

  • Page 1

    Instructions for use salsa r 2 & salsa m 2 powered wheelchair 000690705.

  • Page 2

    2 salsar 2 / salsa m 2 rev.1.0 important: do not use your wheelchair until this manual has been read and understood. User information intended use power wheel chairs: power wheelchairs are exclusively for a user who is unable to walk or has limited mobility, for their own personal use in- and outdoo...

  • Page 3

    Salsa r 2 / salsa m 2 3 rev.1.0 1.0 your wheelchair 7 2.0 how to use this manual 7 2.1 introduction 7 2.2 guarantee 7 2.3 warranty conditions 7 3.0 label explantation / word definitions 8 3.1 definitions of words used in this manual 8 3.2 label explanations 9 4.0 general safety warning and user tips...

  • Page 4: Salsa R

    4 salsar 2 / salsa m 2 rev.1.0 skirt guard anti-tips backrest batteries armrest legrest controller cushion castor footplate drive wheel salsa r 2.

  • Page 5: Salsa M

    Salsa r 2 / salsa m 2 5 rev.1.0 armrest centre mount legrest controller cushion front castor footplate drive wheel skirt guard backrest batteries rear castor salsa m 2.

  • Page 6: Salsa M

    6 salsar 2 / salsa m 2 rev.1.0 dealer signature and stamp salsa m 2 comfort seat armrest centre mount footrest controller comfort cushion front castor footplate drive wheel rear castor comfort back.

  • Page 7

    Salsa r 2 / salsa m 2 7 rev.1.0 1.0 your wheelchair we at sunrise medical want you to get the best out of your salsa wheelchair. This owner’s manual will familiarise you with the chair and its features. It contains hints on everyday usage and general care in addition to information on the high quali...

  • Page 8

    8 salsar 2 / salsa m 2 rev.1.0 4) any repaired or replaced part will benefit from these arrangements for the balance of the warranty period applicable to the wheelchair. 5) parts replaced after the original warranty has expired are covered for a further twelve months. 6) items of a consumable nature...

  • Page 9

    Salsa r 2 / salsa m 2 9 rev.1.0 3.2 label explanations lever position for the left-hand freewheel mechanism salsa m 2 (& salsa from august 2010). Tick = in drive, cross = in freewheel lever position for the right-hand freewheel mechanism salsa m 2 (& salsa from august 2010). Tick = in drive, cross =...

  • Page 10

    10 salsar 2 / salsa m 2 rev.1.0 labels and their descriptions battery label – warning instructions and circuit diagram back rest recline seat lift seat tilt in space the power tilt and power lift/tilt modules are factory fitted for optimum stability and for conformance to strict standard requirement...

  • Page 11

    Salsa r 2 / salsa m 2 11 rev.1.0 4.0 general safety warning and user tips 4.1 general warnings warning! • always ensure that your wheelchair is switched off before attempting to transfer in or out. • always ensure that you are able to operate all controls from a comfortable position. Paying attentio...

  • Page 12

    12 salsar 2 / salsa m 2 rev.1.0 4.9 batteries your wheelchair is supplied as standard from sunrise medical with maintenance-free batteries. These only require regular charging. Before charging, please read sections 10 and 12 in this manual. Warning! Do not, under any circumstances, tamper with the b...

  • Page 13

    Salsa r 2 / salsa m 2 13 rev.1.0 4.11 weight limit danger! • the user plus items carried should never exceed a total weight of 140kg, (160kg salsa r 2 rehab seat). • never use this chair for weight training if the total weight (user plus additional weights) exceed a total weight of 140kg. • exceedin...

  • Page 14

    14 salsar 2 / salsa m 2 rev.1.0 4.16 adverse conditions please be aware that when driving your wheelchair in adverse conditions, e.G. On wet grass, mud, ice, snow or other slippery surfaces, you may experience a reduction in the grip and traction of your wheelchair. Warning! We recommend you take ex...

  • Page 15

    Salsa r 2 / salsa m 2 15 rev.1.0 4.20 anti-tips warning! • make sure that anti-tips are not damaged or worn before using your chair. • attendants must be aware of the location of the anti- tips to prevent feet being trapped underneath causing injury. • attendants - do not stand on the anti-tips, thi...

  • Page 16

    16 salsar 2 / salsa m 2 rev.1.0 4.23 creep mode warning! Please ensure your backrest recline angle relative to floor level, which is a combination of the back recline itself and the tilt angle, does not exceed 12° to drive the chair safely. Note: if the tilt angle exceeds 9° the chair will the chair...

  • Page 17

    Salsa r 2 / salsa m 2 17 rev.1.0 4.26 rear view mirror warning! To avoid injury to people around you please be aware that the mirror protrudes outside the space envelope of the chair and could cause injury to someone when driving past. The mirror must be used on the 10kph model on uk roads. Always m...

  • Page 18

    18 salsar 2 / salsa m 2 rev.1.0 salsa m2 (mwd) approach the kerb in a 90° angle and stop the chair as soon as the castor wheels touch the kerb. Apply sufficient power to the motors to lift the front of the chair up onto the kerb (step) and then apply slightly more power and speed so that the drive w...

  • Page 19

    Salsa r 2 / salsa m 2 19 rev.1.0 4.31 lap belt (standard seat) the lap belt kit. (fig. 4.14). Fastening the lap strap: insert the 3 prong male buckle into the female buckle until a click is heard (fig. 4.15) to fit the lap strap. • place the strap loosely across the seat with the buckle closed.. (fi...

  • Page 20

    20 salsar 2 / salsa m 2 rev.1.0 4.31.1 lap strap rehab seat the 5 cm (2“) aircraft buckle lap strap. (fig. 4.6). The 5 cm (2”) aircraft padded lap strap. (fig. 4.7) the lap strap fitted for a right- handed user. (fig. 4.8) the lap strap fitted for a left- handed user. (fig. 4.9) place the strap loos...

  • Page 21

    Salsa r 2 / salsa m 2 21 rev.1.0 4.32 vr2 controller (fig. 4.21) warning! • avoid knocking your control system and especially the joystick. • be careful not to strike obstacles with the control system or joystick when you drive. • never drop the control system. • when transporting your wheelchair, m...

  • Page 22

    22 salsar 2 / salsa m 2 rev.1.0 fig. 5.4 fig.5.2 fig. 5.1 fig. 5.3 warnings! • make sure, when the chair is stored or left in the car or anywhere else, the controller is switched off and the freewheel mechanisms are engaged. • if there is a need to lift the drive unit the big side frame tubes should...

  • Page 23

    Salsa r 2 / salsa m 2 23 rev.1.0 please ensure the controller is switched off before you engage the release levers – failure to do so will increase the force needed to push the chair. Danger! • this may only be used in an emergency, or if you need to manually push your wheelchair. It is not intended...

  • Page 24

    24 salsar 2 / salsa m 2 rev.1.0 5.5 drive wheel suspension salsa the salsa m2/r2 has an effective and adjustable drive wheel suspension system as a standard feature. To match your requirements on drive comfort, the tension of the springs at the damper can be adjusted. Turning the aluminium ring away...

  • Page 25

    Salsa r 2 / salsa m 2 25 rev.1.0 5.8 standard armrests 5.8.1 armrests-removing and replacing (standard seat). The armrests on both sides of the wheelchair can be flipped up to allow side transfer, (fig. 5.18). For side transfer flip the armrest all the way up until it goes into its mechanical stop. ...

  • Page 26

    26 salsar 2 / salsa m 2 rev.1.0 2.Basic coarse adjustment. Part 1 1. To achieve more than one inch of adjustment, remove the 6mm armrest rotation bolts on both sides of the seat, (fig.5.23). 2. Remove both armrest assemblies. (fig.5.24) 3. Remove both sets of 4mm armrest adjustment ring bolts.(fig.5...

  • Page 27

    Salsa r 2 / salsa m 2 27 rev.1.0 part 2 1. Loosen the 4mm arm pad angle pivot bolts (a) on both armrests. Remove the 4mm angle index bolts (b) on both armrests, (fig.5.30). 2. Use the 5mm fine height adjustment screw (b) to finish fine tuning the height. Turn counter-clockwise to increase height or ...

  • Page 28

    28 salsar 2 / salsa m 2 rev.1.0 position a position b position c standard configuration chart backrest angle (degrees) armrest height (mm) setting ring position -4 305 - 254 a -4 252 - 229 b 0 305 - 254 a 0 252 - 229 b 4 305 - 267 a 4 279 - 229 b 8 305 - 229 b 12 305 - 229 b 12 248 - 229 c 16 305 - ...

  • Page 29

    Salsa r 2 / salsa m 2 29 rev.1.0 5.8.3 standard arm pad position adjustment (fig. 45 - 48) 1. Fine arm pad position adjustments (one to two inches) are possible by loosening the 4mm arm pad adjustment bolts (e) and sliding the arm pad forward or backward as required, (fig.5.36, 5.37). Access to the ...

  • Page 30

    30 salsar 2 / salsa m 2 rev.1.0 5.9 leg rests warning! • be aware of your environment to make sure you do not injure your legs when leg rests are extended. • always ensure that the leg rests or foot plates do not come into contact with the castors before driving the wheelchair. • leg rests are not t...

  • Page 31

    Salsa r 2 / salsa m 2 31 rev.1.0 fig. 5.50 fig. 5.51 fig. 5.52 5.9.1 leg rest removal to swing away the leg rest: • depress the retaining catch and swing the leg rest out, (fig.5.44). • lift the leg rest up and off if removal is required, (fig.5.45). To refit: • line up the holes and studs, (fig.5.4...

  • Page 32

    32 salsar 2 / salsa m 2 rev.1.0 5.9.5 manual articulating / elevating leg rest to elevate: pull the leg rest upwards and stop at the desired height. The leg rest will automatically lock in the chosen position. To lower: push the release lever slowly forward. The leg rest will lower the angle. As soo...

  • Page 33

    Salsa r 2 / salsa m 2 33 rev.1.0 5.9.7 powered centre mount leg rest, (pcml). Warning! There is an option on the programme of the leg rest that allows you to send the footrest to the floor to allow for easier mounting and dismounting for the user. Be aware that when powered the area around and under...

  • Page 34

    34 salsar 2 / salsa m 2 rev.1.0 6.0 seating 6.1 firm seat board the firm seat board is designed to allow pressure relief cushions such as jay to be used, (fig.6.1). 6.2 seat cushions seat cushions supplied by sunrise medical will have velcro® strips that correspond to patches on the seat, (fig.6.2)....

  • Page 35

    Salsa r 2 / salsa m 2 35 rev.1.0 6.9 standard seat height adjustment warning! Make sure the top frame does not trap your fingers. Get someone to hold the seat steady during adjustment. To change the seat height: salsa r2 rear wheel drive only: • remove the two bolts from the front seat posts, using ...

  • Page 36

    36 salsar 2 / salsa m 2 rev.1.0 6.10 standard seat depth adjustment 1. Remove the 5mm depth adjustment bolts from both sides of the seat, (fig.6.11). 6.11 backrest angle adjustment 1. Remove the 5mm backrest bracket index bolts (a) on both sides of the backrest. Loosen the 5mm backrest bracket pivot...

  • Page 37

    Salsa r 2 / salsa m 2 37 rev.1.0 3. Reinsert and tighten both backrest bracket index bolts and bracket bolts (a & b). Use 20 n/m or 177 in/lb of torque, (fig.6.16). Note: the figures below represent the 8°angle. 6.12 back height adjustment 1. Begin by removing the upholstery cover, (fig.6.17). Fig. ...

  • Page 38

    38 salsar 2 / salsa m 2 rev.1.0 4. Remove the 4mm towel bar bolts and the towel bar, (fig.6.20). Note: this step is not necessary in every case. If the push handles are high enough, the towel bar bolts might not thread into the push handle tubes. To test, skip this step and move to numbers 5 and 6. ...

  • Page 39

    Salsa r 2 / salsa m 2 39 rev.1.0 10. Retighten the upholstery straps, (fig.6.26). 11. Reattach the upholstery cover, (fig.6.27). 6.13 manual adjustable backrest (standard seat) for depth adjustment see section 6.8. To recline the backrest angle: • pull the lever at the top of the backrest which oper...

  • Page 40

    40 salsar 2 / salsa m 2 rev.1.0 6.17 headrest to fit the standard headrest, fit the location bracket to the push handles, using the screws and nuts supplied, ensuring that they are fully tightened. To fit the rehab headrest, fit the location bracket to the backrest bracket, using the screws and nuts...

  • Page 41

    Salsa r 2 / salsa m 2 41 rev.1.0 to operate the backrest actuators: • push the mode button to select actuator mode • operate the joystick left or right to select the actuator required (actuator 1 or actuator 2). Selection is indicated via the lighting of the orange led adjacent to the desired actuat...

  • Page 42

    42 salsar 2 / salsa m 2 rev.1.0 6.18.2 powered seat lift the seat can lift up to 30 cm by operating it through your control system. Warning! • before operating the seat lift function ensure that the immediate area around the wheelchair is clear of possible obstructions, • (eg wall shelving), and pot...

  • Page 43

    Salsa r 2 / salsa m 2 43 rev.1.0 7.0 control system 7.0 r-net control system information an alternative control system called r-net is available as an option for the wheelchair. The r-net system has extended options and is suitable for individuals with complex needs or when there is a preference for...

  • Page 44

    44 salsar 2 / salsa m 2 rev.1.0 battery gauge: the battery gauge shows you that the wheelchair is switched on. It also indicates the status of the wheelchair. Refer to chapter 8. Locking/unlocking the wheelchair: the vr2 control system can be locked to prevent unauthorised use. The locking method is...

  • Page 45

    Salsa r 2 / salsa m 2 45 rev.1.0 the horn button: the horn will sound while this button is depressed. Speed / profile decrease button: this button decreases the maximum speed setting or, if the control system is programmed for drive profile operation, selects a lower drive profile. Speed / profile i...

  • Page 46

    46 salsar 2 / salsa m 2 rev.1.0 7.2 vr2-l there are common controls between the vr2 and the vr2-l control systems where a control differs it will be described below. All common controls can be found on the previous page. Lights and indicators: the salsa can be equipped with lights and indicators. Wh...

  • Page 47

    Salsa r 2 / salsa m 2 47 rev.1.0 7.3 vr2 dual control unit control button and indicator: this shows which joystick has control. If the red wheelchair light is on the wheelchair occupants joystick has control. If the green attendant light is on the dual attendant systems joystick has control. The but...

  • Page 48

    48 salsar 2 / salsa m 2 rev.1.0 charger & programming socket control panel joystick battery gauge on-off button horn button max. Speed/ profile indication speed/profile decrease button speed/ profile increase button hazards button lights button actuator button indicator buttons vr2 control panel lay...

  • Page 49

    Salsa r 2 / salsa m 2 49 rev.1.0 8.0 troubleshooting using the vr2 hand control warning! Always consult your sunrise medical authorised dealer when a diagnostic fault has appeared on your hand control. The battery gauge and maximum speed/profile indicator show the status of the control system. Batte...

  • Page 50

    50 salsar 2 / salsa m 2 rev.1.0 self help guide, (fig.8.1). Fault code possible cause the batteries need charging, or there is a bad connection to the battery. Check the connections to the battery. If the connections are good, try charging the batteries the left hand motor has a bad connection. Chec...

  • Page 51

    Salsa r 2 / salsa m 2 51 rev.1.0 9.0 controller mounts 9.1 general warnings: warnings! • do not replace the joystick knob with any unauthorised item. It may cause hazardous operation and loss of control of the chair. • it is important that the joystick boot is replaced if it is torn or brittle; fail...

  • Page 52

    52 salsar 2 / salsa m 2 rev.1.0 9.7 forus control (r-net) warnings! • ensure that you set the speed of the forus control to a speed that you can comfortably follow. • ensure that you always have comfortable access to the controls whilst the chair is moving and make sure that the controller is fixed ...

  • Page 53

    Salsa r 2 / salsa m 2 53 rev.1.0 the forus push handle mechanism is centred with springs which will always bring it back to its centre position when the attendant’s hands are taken off the handles. The push handles can be adjusted in height by releasing the spring loaded pin on the side, adjusting t...

  • Page 54

    54 salsar 2 / salsa m 2 rev.1.0 10.0 speciality controls 10.1 proximity head array warnings • the sensors used in this product will operate if moisture of any substance that is electrically conductive is present in sufficient quantities. • electro magnetic interference from electrical power lines an...

  • Page 55

    Salsa r 2 / salsa m 2 55 rev.1.0 10.4 sip and puff control and buddy buttons warnings • do not wrap the cable around the switch, wrap the cable separately • do not pull on the cable of the switch • do not overload your switch connection, adhere to maximum current ratings • do not immerse the switch ...

  • Page 56

    56 salsar 2 / salsa m 2 rev.1.0 11.0 batteries and charging warning! Please read the owner’s manual supplied with the charger carefully. Warning! Do not expose any part of the battery to direct heat (i.E. Naked flame, gas fire). Warning! When charging always place your charger on a hard surface in a...

  • Page 57

    Salsa r 2 / salsa m 2 57 rev.1.0 11.2 batteries salsa m2 (fig. 11.6 - 11.12) the batteries are contained within the drive unit located under the battery shroud. To remove the batteries: • release the two handle screws under the front of the seat frame that connect the seat frame with the seat module...

  • Page 58

    58 salsar 2 / salsa m 2 rev.1.0 11.3 safety cut-outs in the event of a short circuit there are several safety systems built into your wheelchair to safeguard your electrical circuits. • fusible 100a links are connected into the battery harnesses to protect the batteries and wiring. • a 15a fusible l...

  • Page 59

    Salsa r 2 / salsa m 2 59 rev.1.0 11.8 general charger information the external charger has been designed to charge two 12v gel type batteries connected in series (= 24 v). 11.9 charger safety features the chargers have features which prevent hazards or accidents occurring as a result of connecting b...

  • Page 60

    60 salsar 2 / salsa m 2 rev.1.0 11.12 the range of your vehicle most manufacturers of mobility products state the range of their vehicles either in the sales literature or within the owner’s manual. The range stated sometimes differs from manufacturer to manufacturer even though the battery size is ...

  • Page 61

    Salsa r 2 / salsa m 2 61 rev.1.0 warnings! • an extension cord should not be used unless absolutely necessary. • use of an improper extension cord could result in a risk of fire and electric shock. • if any extension cord must be used, make sure the pins on the plug of the extension cord are the sam...

  • Page 62

    62 salsar 2 / salsa m 2 rev.1.0 12.0 transportation a wheelchair secured in a vehicle will not provide the equivalent level of safety and security of a vehicle seating system. Sunrise medical recommends that the user transfers to the vehicle seating and uses the vehicle- installed restraint system w...

  • Page 63

    Salsa r 2 / salsa m 2 63 rev.1.0 12.2 occupant restraint instructions warnings! • the pelvic restraint belt must be worn low across the front of the pelvis (fig 12.2) so that the angle of the pelvic belt is within the preferred zone of 30° to 75° to the horizontal, (fig 12.3). • a steeper (greater) ...

  • Page 64

    64 salsar 2 / salsa m 2 rev.1.0 12.4 crash testing on the salsa, all models. A representative salsa r2 & salsa m2 wheelchair has been tested in accordance with the dynamic performance requirements specified in iso 7176-19:2001 “wheeled mobility devices for use in motor vehicles” using a q straint 6 ...

  • Page 65

    Salsa r 2 / salsa m 2 65 rev.1.0 12.6 securing the wheelchair into the vehicle (fig. 12.11 - 12.14) warning! All salsa wheelchairs (rwd/mwd) require a six- point tie down system for transportation as shown in the photographs. On the left rear side: • use one of the rear tie down restraints, attach i...

  • Page 66

    66 salsar 2 / salsa m 2 rev.1.0 13.0 maintenance and cleaning caution! It is important that you follow the following cleaning and maintenance schedule in order to keep your wheelchair in tip top condition. 13.1 tyre maintenance and pressures warning! If pneumatic tyres are fitted to your wheelchair ...

  • Page 67

    Salsa r 2 / salsa m 2 67 rev.1.0 fig.13.1 fig.13.2 fig.13.3 fig.13.4 fig.13.5 fig.13.6 fig.13.7 fig.13.8.

  • Page 68

    68 salsar 2 / salsa m 2 rev.1.0 fig.13.9 fig.13.10 fig.13.11 fig.13.12 13.4 removing the castor wheel warning! Castor wheel removal is a safety critical task. If you do not feel confident in carrying out the following instructions, please contact your sunrise medical approved dealer. • note which on...

  • Page 69

    Salsa r 2 / salsa m 2 69 rev.1.0 13.6 inspection of the upholstery/seating tears, dents, wearing or slackening of upholstery particularly near to metal could result in poor posture or lower levels of comfort and pressure relief. 13.7 cleaning seating • you can wash all parts of the covers with a gen...

  • Page 70

    70 salsar 2 / salsa m 2 rev.1.0 13.8 cleaning controls clean the control system and the joystick with a cloth dampened with diluted detergent. Caution! Be careful when cleaning the joystick. Never use abrasive or spirit based cleaners speciality controls ensure that wafer boards, joysticks (all vari...

  • Page 71

    Salsa r 2 / salsa m 2 71 rev.1.0 salsa r 2 parts in the battery box, (fig.13.22): • flip down support tray for 2 x 12v batteries. • 2 x battery looms with fuse and ring terminals. • battery link harness with red and grey connectors. Accessing the batteries • take of the rear cover (fig.13.17). • lif...

  • Page 72

    72 salsar 2 / salsa m 2 rev.1.0 salsa m 2 parts in the battery box, (fig.13.22): • plastic battery box cover for 2 x 12v batteries. • 2 x battery looms with fuse and ring terminals. • battery link harness with red and grey connectors. Accessing the batteries • locate & loosen the 2 hand wheels at th...

  • Page 73

    Salsa r 2 / salsa m 2 73 rev.1.0 13.12 controller access to access the controller on the salsa r2 (rwd) take the rear shroud off (fig. 13.30 - 13.31). To access the controller on the salsa m2 (mwd) take the rear shroud on the base between the rear castor wheels off. A 4.0 mm allan key is required. (...

  • Page 74

    74 salsar 2 / salsa m 2 rev.1.0 13.15 recommended maintenance routines (fig13.35) tools required: battery charger, tyre pump, stiff brush, petroleum jelly cleaning cloth and dilute disinfectant. Warning! If in any doubt about performing any maintenance on your wheelchair, contact your sunrise medica...

  • Page 75

    Salsa r 2 / salsa m 2 75 rev.1.0 • with the seating in an elevated position, drive the wheelchair to make sure that the ‘creep’ mode works which will slow the wheelchair. • drive the wheelchair in each of the drive profiles to make sure the wheelchair performs as it did before. Caution! • if you are...

  • Page 76

    76 salsar 2 / salsa m 2 rev.1.0 model: quickie salsa r 2 (rwd) 14.0 specification sheets (en 12184 & iso 7176-15) manufacturers (europe): sunrise medical gmbh+co.Kg kahlbachring 2-4 69254 malsch/heidelberg deutschland maximum occupant mass (test dummy mass): 140 kg the wheelchair quickie salsa r2 co...

  • Page 77

    Salsa r 2 / salsa m 2 77 rev.1.0 model: quickie salsa m 2 (mwd) maximum occupant mass (test dummy mass): 140 kg the wheelchair quickie salsa conforms to the following standards: a) requirements and test methods for static, impact and fatigue strengths (iso 7176-8) b) power and control systems for el...

  • Page 78

    78 salsar 2 / salsa m 2 rev.1.0 model: quickie salsa r 2 (heavy duty) maximum occupant mass with re-hab seat (test dummy mass): 160 kg the wheelchair quickie salsa conforms to the following standards: a) requirements and test methods for static, impact and fatigue strengths (iso 7176-8) b) power and...

  • Page 79

    Salsa r 2 / salsa m 2 79 rev.1.0 model: quickie salsa m 2 (mwd) with re-hab seat iso7176-15 min. Max. Comments overall length (with legrest) - 1150 mm 70° hanger overall width 610 mm 660 mm 12” / 14” wheels folded length “ “ folded width “ “ folded height 715 mm 715mm backrest folded total mass (w. ...

  • Page 80

    80 salsar 2 / salsa m 2 rev.1.0 15.0 service history this section is designed to assist you in keeping a record of any service and repairs to your wheelchair. Should you decide to sell or exchange your vehicle in the future, this will prove most helpful to you. Your service agent will also benefit f...

  • Page 81

    Salsa r 2 / salsa m 2 81 rev.1.0 dealer signature and stamp:.

  • Page 82

    82 salsar 2 / salsa m 2 rev.1.0 17.0 salsa - salsa m2 battery wiring diagram charger socket: pin 1: battery positive pin 2: battery negative pin 3: inhibit 1 2 3 100a 100a black black red red yellow battery connector battery connector fig.16.1 fig.16.2 fig.16.3 auxiliary power connector c on tr o ll...

  • Page 83

    Salsa r 2 / salsa m 2 83 rev.1.0

  • Page 84

    Om om_salsa r2 - m2_eu_en_rev.1.0_2014_08_11 sunrise medical gmbh & co. Kg kahlbachring 2-4 69254 malsch/heidelberg deutschland tel.: +49 (0) 7253/980-0 fax: +49 (0) 7253/980-222 www.Sunrisemedical.De sunrise medical thorns road brierley hill west midlands dy5 2ld england phone: 0845 605 66 88 fax: ...