1 36” quietcool portable evaporative cooler owner’s manual this manual covers all of the following quietcool portable evaporative coolers. Qc36d1 – quietcool 36” direct drive 1 speed qc36dvs – quietcool 36” direct drive variable speed (shown above) qc36b1 – quietcool 36” belt drive 1 speed ½ hp qc36...
2 file this owner’s manual in a safe place for future reference. It contains operating procedures – maintenance procedures – trouble shooting guide – replacement parts guide – order form – and contact information. You will need this! Warnings and cautions read before operating quietcool portable eva...
3 quietcool portable evaporative cooler table of contents 1.0 introduction 1.1 quick start 1.2 operate unit for 2 weeks before adding evap-o-matic tablets 2.0 how evaporative cooling works 3.0 unpacking your new quietcool unit 4.0 set-up your quietcool unit 4.1 connecting the electrical supply 4.2 c...
4 quietcool portable evaporative cooler 1.0 introduction your quietcool was engineered to be the most efficient portable evaporative cooler manufactured. It was manufactured and assembled at our plant in houston, texas. Your quietcool was tested 3 ways. Your unit was tested for 1. Maximum air flow a...
5 4.1 connecting the electrical supply all quietcool models require regular 3 prongs, ground with 120 volt power supply. Plug electrical cord into receptacle. If using an extension cord be sure it is rated for at least 20 amps for the distance your cord is running. To be safe – make sure no other eq...
6 open the valve to 1 ¼ turn. Allow water to run for 10 – 15 minutes on new cooling pads to totally saturate them with water. Once your units cooling pads are saturated – then, you are ready to turn on fan and begin to feel the cooling effect from your new quietcool. Note: after your cooling pads ar...
7 two bolts hold the metal angle retaining bar and the cooling pads in place. Next, remove the angle retaining bar and set to side. Now you are ready to remove your unit’s cooling pads. 7.2 removing the cooling pads before your start, make a note of the direction of the angle of the pads flutes (see...
8 7.5 quietcool trouble shooting guide problem 1. Water on the floor a. Front of unit . . . B. Back of unit 2. Found water on floor after overnight shut off. 3. Foul odor from fan a. New unit . . . B. After normal use . . . 4. No water running over the pads . . . Cause too much water. Damage to poly...
9 problem (continued) 5. Scale build-up on cooling pads. Cause (continued) hard water with excessive mineral content. Solution (continued) use evapo-o-matic tablets or add a water stabilizer at the discharge side of the pump. See accessories section 9.0. Flush water from unit’s water reservoir more ...
10 9.0 accessories qcg1001 – water stabilizer for 36” unit. The water stabilizer removes harmful calcium, scale build-up and algae by keeping it from collecting anywhere within your unit. The calcium and scale is flushed out of your unit when you flush out the sump – extending the life of your cooli...
11 10.0 replacement parts all accessories / replacement parts are obtainable through your local quietcool distributor. Should a part be temporarily out of stock at your distributor he can special order it for you. You can contact the manufacturer, quietaire cooling inc. Directly at: telephone: 713.2...
12 11.0 order form fax back order form accessories and replacement parts for all qc48” fan blade models. For all motors, pulleys, belts, switches and fan blades call quietaire at 713.228.9421. Accessories description part number quantity amount price intake pre-filter – protects cooling pads from ai...
13 12.0 wiring diagrams for all 36” units.
14.
15.
16 13.0 warranty warranty warranty and disclaimer: quietaire cooling extends this limited warranty to the original buyer and warrants that products manufactured by quietaire cooling shall be free from original defects in workmanship and material for one year from date of shipment, provided same have...
