1 48” quietcool portable evaporative cooler owner’s manual this manual covers the qc48b2 quietcool portable evaporative cooler. Qc48b2 – quietcool 48” belt drive 2 speed optional cover for storage protection. See section 9.0 for details and a convenient fax back order form..
2 file this owner’s manual in a safe place for future reference. It contains operating procedures – maintenance procedures – trouble shooting guide – replacement parts guide – order form – and contact information. You will need this! Warnings and cautions read before operating quietcool portable eva...
3 quietcool portable evaporative cooler table of contents 1.0 introduction 1.1 quick start 1.2 operate unit for 2 weeks before adding evap-o-matic tablets 2.0 how evaporative cooling works 3.0 unpacking your new quietcool unit 4.0 set-up your quietcool unit 4.1 connecting the electrical supply 4.2 c...
4 quietcool portable evaporative cooler 1.0 introduction your quietcool was engineered to be the most efficient portable evaporative cooler manufactured. It was manufactured and assembled at our plant in houston, texas. Your quietcool was tested 3 ways. Your unit was tested for 1. Maximum air flow a...
5 4.1 connecting the electrical supply all quietcool models require regular 3 prongs, ground with 120 volt power supply. Plug electrical cord into receptacle. If using an extension cord be sure it is rated for at least 20 amps for the distance your cord is running. To be safe – make sure no other eq...
6 little to slow the water flow. After the pads are wet – you can open the valve to 1 ¼ turn. Allow water to run for 10 – 15 minutes on new cooling pads to totally saturate them with water. Once your units cooling pads are saturated – then, you are ready to turn on fan and begin to feel the cooling ...
7 7.2 removing the cooling pads before your start, make a note of the direction of the angle of the pads flutes (see side of pads). You must put pads back in correct order for your unit to function effectively. (note: install steep side 45° angle flute to the back of unit.) once the retaining angle ...
8 problem (continued) b. Back of unit 2. Found water on floor after overnight shut off. 3. Foul odor from fan a. New unit . . . B. After normal use . . . 4. No water running over the pads . . . 5. Scale build-up on cooling pads. Cause (continued) damage to polyethylene housing. Note: check for possi...
9 8.0 storage remove pads as described above in 7.2 and rinse pads clean with fresh water. Dry cooling pads in sunlight. Drain water reservoir completely and wipe dry. Replace dry cooling pads. Replace top angle bar to hold pads in place. Store quietcool in dry, clean area and cover (you can order a...
10 9.0 accessories qcg1001 – water stabilizer for 48” unit. The water stabilizer removes harmful calcium, scale build-up and algae by keeping it from collecting anywhere within your unit. The calcium and scale is flushed out of your unit when you flush out the sump – extending the life of your cooli...
11 10.0 replacement parts all accessories / replacement parts are obtainable through your local quietcool distributor. Should a part be temporarily out of stock at your distributor he can special order it for you. You can contact the manufacturer, quietaire cooling inc. Directly at: telephone: 713.2...
12 11.0 order form fax back order form accessories and replacement parts for all qc48” fan blade models. For all motors, pulleys, belts, switches and fan blades call quietaire at 713.228.9421. Accessories description part number quantity amount price intake pre-filter – protects cooling pads from ai...
13 12.0 wiring diagrams for the 48” unit.
14 13.0 warranty warranty warranty and disclaimer: quietaire cooling extends this limited warranty to the original buyer and warrants that products manufactured by quietaire cooling shall be free from original defects in workmanship and material for one year from date of shipment, provided same have...
