1. DL manuals
  2. Quietside
  3. Water Heater
  4. DPW-199C
  5. User Manual

Quietside DPW-199C User Manual

Summary of DPW-199C

  • Page 1

    This appliance is certified for use without any limitation of the any altitude installation. However for better combustion, from 2,000ft to 4,500ft installation decrease the manifold pressure 0.3' w.C.For natural gas. From 4,500ft to 6,000ft installation derease the maniforld pressure 0.6'w.C. From ...

  • Page 4

    Doesn’t match supplied gas and specified gas, case.

  • Page 6

    ,.

  • Page 8

    Dpw-199c.

  • Page 9

    This water heater shall not be connected to any heating system or component(s) previously used without thoroughly flushing the system prior to filling. Contaminated space heating water can cause scale or sludge build-up which affects the system efficiency and life of unit and its components..

  • Page 15

    Control dial when the boiler is operating, burner lamp is on. Space heating button push this button to turn on space heating mode and set the temperature of space heating water. When it’s turned on, on left side of lcd. Power button use this button to turn on/off the boiler. Outdoor reset button ind...

  • Page 16

    Dsr-420f ℉ auto.Eco dsr-420f ℉ auto.Eco controlling the control dial dsr-420f ℉ auto.Eco dsr-420f ℉ auto.Eco using the control dial. 42 is blinking..

  • Page 17

    Dsr-420f ℉ auto.Eco dsr-420f ℉ auto.Eco dsr-420f ℉ auto.Eco use the control dial the control dial.

  • Page 18: Heating Curves

    Dsr-120f ℉ auto.Eco ℉ outdoor reset press the power button to turn the unit on. Press the outdoor reset button, the boiler use the reset function. In outdoor reset mode, unit ignores the set temp and operates according to heating curve graph depending on your selected reset ratio. ℉ to set the reset...

  • Page 20

    1.85gal in the.

  • Page 22

    Dsr-420f ℉ auto.Eco heating loop does not have enough water to operate. Fill the loop by opening #6 water supply valve. (normal operation pressure of closed loop: 14~28psi).

  • Page 23

    Bleed air out and fill the system as instructed as above. Air in the system can trigger low water level warning light..

  • Page 25

    195,000 3" or 4" 3" or 4" 3.5" or 4.5" dpw-199c max vent length (feet) 38ft equivalent each for both intake and exhaust 4" 3" 45ft equivalent each for both intake and exhaust.

  • Page 26

    120 118 119 dpw-199c.

  • Page 28

    347 348 349.

  • Page 29

    Part list no no part no part no part name part name 101 2010435 case assembly 219 2100320 combustion fan assembly 102 2070476 flue collar(3") 103 3040379 chassis assembly 104 3040378 air intake connector(3") 105 3090260 flue collar sealing packing 107 2070470 expansion vessel 106 108 109 2080845 exp...

  • Page 30

    Part list no no part no part no part name part name 342 3030198 chw return connector 335 2060229 flow switch 336 2060228 water supplementation device 337 3010925 fixing clip(p6) 338 3030200 expansion vessel connector nipple 339 3080181 packing(p14.5) 340 3120030 pump fixing clip 341 3080103 o-ring(p...

  • Page 32

    2) 7.1~21.3 psi.

  • Page 33

    ※ see the page30, #305 “2080390: overheat thermostat” s.

  • Page 34

    (closed circuit) not closed (off) not closed.

  • Page 35

    If pcb is not supplying 120v, replace pcb. Caution : only check this with gas supply turned off measure the voltage at the both blue gas valve wires, then check the both white gas valve wires. If the solenoid valve become to be closed although the voltage reading is 120v, the gas vlave should be rep...

  • Page 36

    The burner is not operating, pcb should be replaced. Measure the voltage at the both blue gas valve wires, then check the both white gas valve wires..

  • Page 37

    1) make sure flame sensing rod is not touching the burner. 2) there is no voltage to the gas valve but there are small flames in the combustion chamber area when the unit stops running..

  • Page 38

    104℉=26.069Ω 122℉=17.599Ω 140℉=12.139Ω 158℉=8.540Ω 176℉=6.142Ω 68℉=61.451Ω 86℉=39.522Ω.

  • Page 39

    S.

  • Page 40

    Problem with drain make sure drain hose is not clogged or frozen..

  • Page 41

    3 3.

  • Page 42

    Mounting plate securely. Make sure the unit is mounted on a non-combustible material. It may cause mounting screw corrosion and result in failure. From unit falling. From unit falling. Mounting bracket is not strong enough, the appliance can fall..

  • Page 43

    Mounting bracket. Mounting bracket.With wall plug mounting bracket.

  • Page 44

    Or.

  • Page 46

    3" or 4" 3" or 4".

  • Page 47

    Dpw-199c multiple vent terminals vertically in-line. Do not cover the vent terminal with any type of protective screen or enclosure. In-line or blocked terminals can cause abnormal combustion resulting undesired performance from the water heater..

  • Page 48

    3" or 4" see table 1 below. Max. Flue length equivalent model vent size dpw-199c 3" pvc 4" pvc 38 feet 45 feet table 1. Dpw-199c 5. Minimum pipe length of 10ft is recommended to prevent freezing air entering the unit in cold climate. ( one elbow is equal to 5ft length ) pvc pipe extension is recomme...

  • Page 49

    Vent size 3" pvc 4" pvc.

  • Page 50

    Turn 90 degree elbow away from exhaust side..

  • Page 51

    Vent size 3" pvc 4" pvc.

  • Page 52

    #1 other venting option it is allowed to run exhaust flue pipe through a different wall from air intake pipe side. Maximum allowed flue length remains the same. (table on page 52) the 90 degree elbow must be installed to the air intake pipe..

  • Page 53

    #2 (single pipe venting) dpw-199c : 3" or 4" schejule 40 pvc dpw model see table 1 below. 53 5. Minimum pipe length of 10ft is recommended to prevent freezing air entering the unit in cold climate. Max. Flue length equivalent model vent size dpw-199c 3" pvc 4" pvc 38 feet 45 feet table 1. ( one elbo...

  • Page 54

    #3 (concentric vent termination) 2" & 4" concentric vent schedule 40 pvc 6" & 4" concentric vent schedule 40 pvc 38 min. 1ft 38 dpw-199c dpw model 54 other venting option 5. Minimum pipe length of 10ft is recommended to prevent freezing air entering the unit in cold climate. ( one elbow is equal to ...

  • Page 55

    Dpw-199c other venting design #4 (snorkel flue) 38 feet dpw model 55 5. Minimum pipe length of 10ft is recommended to prevent freezing air entering the unit in cold climate. ( one elbow is equal to 5ft length ) pvc pipe extension is recommended to prevent recirculation of flue gas. Max. Flue length ...

  • Page 56

    38 (11.6meters) 38 (11.6meters) 38 (11.6meters) 32 27 22 of 4" pvc typical venting & non-direct venting concentric vent termination & 3" vent 56.

  • Page 57

    #4 (snorkel flue) other venting option #5 (vertical venting) please note exhaust gas flue connetor for odw-180 & 199 is on the opposite side from odw-099 & 120 (reference : page 8 & 9) see table 1 below. ( one elbow is equal to 5ft length ) 4. Minimum pipe length of 10ft is recommended to prevent fr...

  • Page 58

    58 the below reference. The below reference.

  • Page 59

    59.

  • Page 60

    60

  • Page 61

    61.

  • Page 62

    62.

  • Page 63

    63.

  • Page 64

    Insulation 64.

  • Page 65

    65 dsr-420f.

  • Page 66

    66.

  • Page 67

    Dpw-199c 67.

  • Page 68

    68.

  • Page 69

    69.

  • Page 70

    70

  • Page 71

    71.

  • Page 72

    72 dsr-420f.

  • Page 73

    73.

  • Page 74

    74.

  • Page 75

    75.

  • Page 76

    76.

  • Page 77

    77 d s r -4 2 0 f dsr-420f ℉ auto.Eco.

  • Page 78

    78 d s r -4 2 0 f dsr-420f ℉ auto.Eco.

  • Page 79

    79 d s r -4 2 0 f dsr-420f ℉ auto.Eco.

  • Page 80

    80 d s r -4 2 0 f dsr-420f ℉ auto.Eco.

  • Page 81

    Quiteside corp - midwest office 3001 northern cross blvd #361 fort worth tx 76137 phone : 817-838-6066 fax : 817-838-8670 quiteside corp - east coast office 6 pine hill dr carlisle pa 17013 phone : 866-243-6498 fax : 717-243-7917 website : www.Quietside.Com quiteside corp - corporate office 8750 pio...