Quiko QK-Intkey User Manual - page 3
3
E
N
G
L
I
S
H
Storing a new access code
Enter the programming code: if not changed is: 123456 confirm with *, the green led will blink. Now the following
sequence should be entered: memory cell number (2 digits), access code (2-6 digits),and for verification again the same
memory cell number, the same access code. Confirm with *. To finish press:
. You can add more access codes in cells
01-98 in the same way. To use the access code: press the access code followed by *. For example storing the code 9124
in cell number:01. Press: 123456 *, 01 then 9124 and again 01 and 9124 confirm with *. To finish press:
.
Changing the programming code
Enter the programming code: if not changed is: 123456 confirm with *, the green led will blink. now the following sequence
should be entered: memory cell number 99 , new programming code ,and for verification again the memory cell number 9,
the same new programming code. Confirm with *. Now you can add access codes in cells 01-98 as described or exit. To
finish press:
. For example changing the programming code to: 649731. Press: 123456 *, 99 then 649731 and again
99 and 649731 confirm with *. To finish press:
. You should keep this code because this is the only way to enter the
programming mode!
Back to Initiate status – default
Using an internal jumper the initial programming code can be restored. The access codes will not be changed.Turn the
power off. dismount the panel. Install a jumper on pins labeled: DEFAULT turn on the power, a long “Beep” will be sound
for confirmation. Turn off the power and take out the jumper. Reinstall the panel. The Intercom Encoder returns to normal
condition. The Programming code now is: 123456 *.
Canceling an access code
A particular access code could be cancel if its memory cell location is known. Enter the programming code: if not changed
is: 123456 *, the green led will blink. now the following sequence should be entered: memory cell number to cancel(2
digits), and
.for verification again the same memory cell number, and
. Confirm with *. For example:
canceling the code stored in cell number 37: press the following sequence:
123456 *, 37
37,
*. To finish
press:
.
Setting opening times values
A different opening time value can be set to opening via the keyboard and via the optional bypass pushbutton. The times
values are from 1 second till 9 seconds. Enter the programming code: if not changed is: 123456 *, the green led will blink.
Now the following sequence should be entered: memory cell number 00, opening time via keyboard (1 digit) followed by
opening time via bypass pushbutton (1 digit). for verification repeat the same sequence of memory cell number 00
opening times values. Confirm with *. To finish press:
. Remark: when setting the keyboard opening time, a value to the
bypass pushbutton must be set also, even if not installed. For example setting the keyboard opening time to 5 sec. And
pushbutton to 7 sec. Press: 123456 *,00 then 5 then 7 and again 00 and 5 and 7 confirm with *. To finish press:
.
Examples
Programming option
Execution
Default
Entering programming code
123456 *
Changing programming code
For example: new code 777456
Enter programming code, *
99-777456 99-777456 *
123456
Storing a new access code
For example: cell number 01 access code: 2040
Enter programming code, *
01-2040 01-2040 *
All the cells are empty (not 0)
Cancelling access code stored in cell number 37 Enter programming code, *
37-
37-
*
Setting opening time from keyboard to 2
seconds and from bypass pushbutton to 5
seconds
Enter programming code, *
00-25 00-25 *
3 seconds from keyboard,
3 seconds from bypass pushbutton
Microphone and speaker volume adjustments
The Intercom Encoder unit leaves the manufacturer site adjusted. Sometimes because of the location (opened or closed
space), acoustical problems occur. If the Encoder’s speaker sound level is too high or low, gently rotate the internal SP
potentiometer.(clockwise to lower volume). If the sound level of the Encoder in the handset is too high or low, gently rotate
the internal MIC potentiometer. (clockwise to lower volume)
Operation
Calling at the door: Press shortly on the Bell
. Wait for vocal answer. If authorized, the lock will buzz and you may
enter.
Opening the lock using the keyboard: Enter the access code confirm with *. The lock will be open for the time value it was
programmed. Each key stroke is followed by a Beep sound, entering a false code or invalid pressing is followed by a
“Beep-Beep-Beep” sound sequence. When exit the secured area press the bypass pushbutton, the lock will be open for
the programmed time value (could be set to different value than entering).