Quirky R-INS-TAPT-WH02 Installation Instructions

SMART  

SWITCH

TAPT

IN THE BOX

•  Wall switch assembly kit with pre-stripped,  

stranded wires (green, red, white, and black), 

and 4 wire connectors (for wires up to  

12 gauge)

•  Faceplate (hides visible screws)

•  Snap plate (pre-attached)

•  User guide 

Note: The included faceplate and snap plate  

are intended for single gang box installations 

only. If installing in a double gang box, use a 

double gang wall plate (not included) without  

the faceplate and snap plate. 

WHAT YOU’LL NEED

•  A Wink HUB or ZigBee-enabled, Wink-

certified hub (sold separately) 

•  Apple® or Android™ smart device (tablets  

and desktops not supported)

•  The Wink app downloaded to your mobile 

device from the iTunes® App Store or Google 

Play™. If you already have the Wink app 

installed, please download the latest version  

to ensure you have the most updated support.

•  A Wi-Fi® network connection with a router 

using WPA-PSK security. WEP security is 

not supported. Please refer to your router’s 

manual for instructions on converting your 

router to WPA security.

•  Slotted screwdriver and Phillips head 

screwdriver  

IMPORTANT SAFETY INFORMATION

•  Read all instructions and warnings prior to 

using Tapt. Failure to comply with instructions 

and warnings constitutes improper use of Tapt. 

Save all instructions.

•  Quirky, Inc. not responsible for improper  

use, which may result in personal injury or 

product damage.

•  Not a toy. Keep away from children.

•  WARNING: RISK OF ELECTRIC SHOCK  

OR FIRE. Before installing, servicing, or 

removing Tapt, TURN OFF POWER AT THE 

CIRCUIT BREAKER THAT CONTROLS THE 

SWITCH. After power has been turned off, 

make sure the light switch you are going to 

replace with Tapt is powered down before 

continuing installation. It is recommended to 

use a circuit tester to make sure the circuit 

is off. Exercise extreme caution when using 

devices controlled via Tapt.

•  This device is intended for installation and 

use in accordance with the National Electric 

Code (NEC) and local regulations in the United 

States, or the Canadian Electrical Code (CEC) 

and local regulations in Canada.

 If you are 

unsure or uncomfortable about performing 

this installation, consult a qualified electrician.

•  Tapt is a single pole switch and a neutral 

connection is required.

•  Tapt is not compatible with a 3-way light switch. 

•  NOT FOR USE WITH MEDICAL OR LIFE 

SUPPORT EQUIPMENT. App-enabled 

devices should never be used to supply power 

to or control the On/Off status  

of medical and/or life support equipment.

•  Do not use to control electric heaters or 

any other appliances which may present a 

hazardous condition due to unattended or 

unintentional or automatic power on control.

•  120VAC. Must not exceed 600 watts 

(Incandescent); 15 Amps, 1800W (Resistive);  

or 1⁄2 HP (Motor). The maximum rating for 

entire switch is 1800W (15A) Resistive.

•  There are no user-serviceable parts.

•  Only use this device with copper or copper- 

clad wires.

COMPLIANCE

This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 

(1) this device may not cause harmful interference, and 

(2) this device must accept any interference received, 

including interference that may cause undesired 

operation.

Changes or modifications not expressly approved by the 

party responsible for compliance could void the user’s 

authority to operate the equipment.

NOTE: This equipment has been tested and found 

to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against 

harmful interference in a residential installation. This 

equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful 

interference to radio communications. However, there 

is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause 

harmful interference to radio or television reception, 

which can be determined by turning the equipment 

off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment  

and receiver.

•  Connect the equipment into an outlet on a circuit 

different from that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV 

technician for help. 

This equipment complies with FCC radiation exposure 

limits set forth for an uncontrolled environment. This 

equipment should be installed and operated with minimum 

distance 20cm between the radiator & your body.

The country code selection is for non-US models only  

and is not available to all US models. Per FCC 

regulations, all Wi-Fi products marketed in US must be 

fixed to US operation channels only. 

This device complies with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the 

following two conditions: 

(1) this device may not cause interference, and (2) 

this device must accept any interference, including 

interference that may cause undesired operation of 

the device.

LIMITED ONE-YEAR WARRANTY

Quirky, Inc. (“Quirky”) Original Purchase Product 

Warranty: 

Quirky warrants to the original purchaser (“Purchaser”) of 

this Quirky product, for the period of one (1) year following 

the date on which Purchaser purchases the product, that 

the product shall be free of defects in design, assembly, 

material, or workmanship.

Quirky will refund or replace, at its option, any defective 

product free of charge.

In order to qualify for this warranty, the Purchaser must 

provide the defective product and a copy of the original 

receipt of purchase to Quirky for inspection. The receipt of 

purchase must indicate the product purchased, price paid, 

date of purchase, and name of merchant.

To request service under this warranty, contact Quirky at 

866-5-QUIRKY or questions@quirky.com and a Quirky 

representative will provide instruction on how to proceed.

This warranty shall be null and void if Quirky determines 

that the product has been improperly installed, altered 

or tampered with in any way. This warranty does not 

protect against normal use, wear and tear, or damage due 

to abuse.

THIS WARRANTY CONTAINS THE SOLE WARRANTY 

OF QUIRKY. THERE ARE NO OTHER WARRANTIES, 

EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED 

WARRANTY OR CONDITION OF QUALITY, 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR 

PURPOSE, AND SUCH IMPLIED WARRANTIES, IF 

ANY, ARE LIMITED IN DURATION TO THE TERM OF 

THIS WARRANTY. IN NO EVENT SHALL QUIRKY 

BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, 

INDIRECT OR CONSEQUENTIAL DAMAGES SUCH AS, 

BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS 

ARISING OUT OF THE SALE OR USE OF ANY QUIRKY 

PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF 

SUCH DAMAGES.

Some jurisdictions do not allow exclusions or limitations 

on implied warranties or incidental, consequential or other 

damages, so the above exclusions and limitations may not 

apply to you.

COPYRIGHT AND TRADEMARK NOTICES

©2014 Quirky, Inc. All rights reserved.

Quirky is a registered trademark of Quirky, Inc.

Wink is a trademark of Wink, Inc.

GE is a registered trademark of General Electric Company 

and is under license by Quirky, Inc.

Wi-Fi is a registered trademark of the Wi-Fi Alliance.

ZigBee is a registered trademark of ZigBee Alliance.

Apple and iTunes are registered trademarks of Apple, Inc.

App Store is a service mark of Apple, Inc.

Android and Google Play are trademarks of Google, Inc.  

SUPPORT

Need help?

Email questions@quirky.com 

Call 1-866-5QUIRKY

•  Switches can be used to turn standard  

or smart bulbs on or off 

•  Programmable features within the Wink app 

allow switches to dim smart bulbs

•  Tapt can trigger other smart products with  

one touch (e.g., Push one of its buttons when 

you wake up to open all of your smart blinds, 

adjust the smart thermostat to a desired 

temperature, and turn on smart light bulbs)

•  Switches allow you to schedule standard  

bulbs to turn on/off

R-I

NS-

TA

PT-

WH

02  |  r

ev1

20

914

 INVENTED BY 

Michael Taylor

+2020 INFLUENCERS

Tapt was invented by Michael Taylor,  

a business analyst from Canton, GA.

An energy-conscious dad of three, 

Michael was constantly following  

his kids around to make sure they  

turned off lights, TVs, and ceiling fans. 

He came up with Tapt so he could 

manage his household at a glance. 

These days, you’re likely to find  

Michael practicing taekwondo,  

running a Spartan race, or listening  

to Weird Al Yankovic.

PART # : R-INS-TAPT-WH02

SPEC : 100gsm bright white C2S, Matte UV

FLAT DIMS : 220 x 336 mm

FINISHING : Z-fold both ways

PANTONE

115 C