1. DL manuals
  2. Qvis
  3. Security Camera
  4. APO-VANIR-2
  5. User Manual

Qvis APO-VANIR-2 User Manual

Manual is about: 1.3 & 2 MEGA PIXEL VANDAL DOME IP CAMERAS

Summary of APO-VANIR-2

  • Page 1

    Apoip-van apo-vanir-2 1.3 & 2 mega pixel vandal dome ip cameras user’s manual v1.0 08 / 2013.

  • Page 2

    I.

  • Page 3: Welcome

    Ii welcome thank you for purchasing the 1.3 or 2mp vandal dome ip camera . This user ’s manual is designed to be a reference tool for the installation and operation of your system. Here you can find information about the corresponding ip camera ’s features and functions, as well as a detailed instal...

  • Page 4

    Iii important safeguards and warnings 1 ． electrical safety all installation and operation here should conform to your local electrical safety codes. The power supply shall conform to the requirement in the selv (safety extra low voltage) and must make sure that the limited power source is rated 12v...

  • Page 5

    Iv please make sure the ccd (cmos) component is away from the radiation of the laser beam device. Otherwise it may result in ccd (cmos) optical component damage. It is recommended that the grounding studs of the product should be grounded, so to further enhance the reliability of the camera. 6. Dail...

  • Page 6: Table Of Contents

    V table of contents 1 general introduction ...................................................................................................... 1 1.1 overview ........................................................................................................... 1 1.2 features ...................

  • Page 7

    © copyright qvis ®. All documentation rights reserved. 1 1 general introduction 1.1 overview this network camera integrates traditional camera and network video technology. It adopts both audio and video data collection and transmission simultaneously. Because of inbuilt internal hardware it can con...

  • Page 8

    © copyright qvis ®. All documentation rights reserved. 2 network management allows network camera configuration and management via ethernet. Supports device management via web or client-end. Power external power adapter dc12v. Power over ethernet (poe). Conforms to the ieee802.3af standard. Connect ...

  • Page 9

    © copyright qvis ®. All documentation rights reserved. 3 exposure mode manual/auto pal: ranges from 1/3 to 1/10000. Video compression standard h.264/mjpeg video frame rate pal: main stream(1280*960@25fps) extra stream(352*288@25fps), main stream(1280*720@25fps ） extra stream(352*288@25fps ） pal: mai...

  • Page 10

    © copyright qvis ®. All documentation rights reserved. 4 smtp, ftp, dhcp, dns, ddns, pppoe, upnp, ntp, bonjour, snmp. Max. Ir leds length 20 metres aux port power dc 12v and poe(802.3af) g en eral p ar amet er power consumption 6w max working temperature -10 o c~+60 o c protection level ip66 & ik10 ...

  • Page 11: 2  Structure

    © copyright qvis ®. All documentation rights reserved. 5 2 structure 2.1 dimensions you can refer to the following figures for dimension information. The unit is mm (see figure 2- 1 & figure 2- 2 ) . Figure 2- 1 dimension illustration 1 figure 2- 2 dimension illustration 2.

  • Page 12

    © copyright qvis ®. All documentation rights reserved. 6 2.2 port description the port is shown in figure 2 – 3 and figure 2 – 4. Figure 2 - 3 port 1 figure 2 - 4 port 2.

  • Page 13

    © copyright qvis ®. All documentation rights reserved. 7 please refer to the following sheet for external connection port definition information: sn port port name connector function description 1 power ac 24v power port / connect to ac 24v power. Only some series support ac 24v. 2 power dc 12v powe...

  • Page 14

    © copyright qvis ®. All documentation rights reserved. 8 2.3 bidirectional talk 2.3.1 device-end to pc-end device connection 1. Please connect the speaker or the mic to the audio input port found in the device rear panel. Then connect the earphone to the audio output port in the pc. 2. Login to the ...

  • Page 15

    © copyright qvis ®. All documentation rights reserved. 9 2.4 alarm setup the alarm interface is shown in figure 2 – 5. Please follow the steps listed below for local alarm input and output connection. 1. Connect the alarm input device to the alarm input port (no.4 pin) of the i/o cable. 2. Connect t...

  • Page 16

    © copyright qvis ®. All documentation rights reserved. 10 figure 2 – 6 alarm input please refer to the following figure for alarm output information (see figure 2 – 7). Port alarm_c and port alarm_no composes an on-off button to provide the alarm output. If the type is no, this button is normal open...

  • Page 17

    © copyright qvis ®. All documentation rights reserved. 11 3 installation important: before you complete the installation and setup, do not remove the electrostatic attraction film on the transparent enclosure. Otherwise it may result in injury. After removal electrostatic attraction film, do not tou...

  • Page 18

    © copyright qvis ®. All documentation rights reserved. 12 3.2 device installation steps 3.2.1 general installation the general interface is shown as in figure 3 – 2. Figure 3- 2 general installation 1 step 1: take the installation position diagram from the accessories bag and then paste it on the in...

  • Page 19

    © copyright qvis ®. All documentation rights reserved. 13 figure 3- 3 general installation 2 step 3: adjust the device chassis and pull the cable through the exit hole. Make the fixture hole on chassis face the three plastic expansion bolts (in step 1). Take 3 x st3.0 self-tapping screws out from th...

  • Page 20

    © copyright qvis ®. All documentation rights reserved. 14 3.2.2 manual zoom lens focus operation the manual zoom lens focus interface is shown as in figure 3 – 4. Figure 3 – 4 manual zoom lens step 1: slightly loosen the adjusting screw e and push the adjust screw e to make it swing. Adjust the lens...

  • Page 21

    © copyright qvis ®. All documentation rights reserved. 15 3.2.4 cable connection there are two reserve cable exits provided on the camera’s chassis. The pin diameter should be no less than 15mm. One of the cable exits has a m22 screw thread and can work with the default combination cable to remove t...

  • Page 22

    © copyright qvis ®. All documentation rights reserved. 16 3.3 micro sd card installation warning! Please unplug the device power cable and then shut-down the device before you install the micro sd card. Step 1 please refer to step 2 in chapter 3.2.1 to open the device protection enclosure. Step 2 pl...

  • Page 23

    © copyright qvis ®. All documentation rights reserved. 17 4 quick configuration tool 4.1 overview quick configuration tool can search current ip address and modify ip address. At the same time, you can use it to upgrade the device. Please note: the tool only applies to the ip addresses in the same s...

  • Page 24

    © copyright qvis ®. All documentation rights reserved. 18 figure 4-2 search interface 2 select the ‘open device web’ item; you can go to the corresponding web login interface (see figure 4-3 ) . Figure 4-3 web login if you want to modify the device ip address without logging in to the device web int...

  • Page 25

    © copyright qvis ®. All documentation rights reserved. 19 please note the port information here shall be identical with the port value you set in tcp port in web network interface. Otherwise, you cannot login the device. If you are using device background upgrade port 3800 to login, other setups are...

  • Page 26

    © copyright qvis ®. All documentation rights reserved. 20 5 web operation this ip camera product supports the web access and management using a pc. Web includes several modules: monitor channel preview, system configuration, alarm, etc. 5.1 network connection please follow the steps listed below for...

  • Page 27

    © copyright qvis ®. All documentation rights reserved. 21 figure 5-2 web login if it is your first time logging in, the system pops up warning information to ask you whether to install the control ‘ webrec.Cab ’ or not, after you have logged in for one minute. Please click ok button, the system can ...

  • Page 28

    © copyright qvis ®. All documentation rights reserved. 22 after you logged in, you can see the main window. See figure 5-4: figure 5-4 web monitoring window.

  • Page 29

    © copyright qvis ®. All documentation rights reserved. 23 6 faq bug solution / reason i cannot boot up the device or operate it properly. Please click the reset button for at least five seconds to restore factory default setup. The water has leaked into the camera casing the unauthorised front or re...

  • Page 30

    © copyright qvis ®. All documentation rights reserved. 24 for more information about our ip cameras and other available cameras, nvrs & accessories, please visit our website: www.Adata.Co.Uk alternatively scan this qr code with your smart phone to be directed instantly to our website:.