- DL manuals
- Qvis
- DVR
- APOLLO PRO DC LX
- User manual
Qvis APOLLO PRO DC LX User manual - page 7
7
5). Connect SATA data wire
6). Connect the power wire
7). Put the top back on
8). Screw on the cover
2.3 Rack mount installation
ThisseriesofDVRisinastandard2Ucase,soitcanberackmounted.
Step:
1. Make sure the room temperature is lower than 35°C (95°f)
2.Keepatleast15cmspacearoundtheDVRtoallowairtoflow
3. Installation is from bottom to top
2.4 Front panel (may vary on some models)
(1) Direction/OK
(2) Play Pause/1
(3)Previousfile/2
(4) Nextfile/3
(5) Playback Pause/4 (6) Indication light
(7) Playback Stop / 5 (8) IR remote receiver
(9) Record search/ 6 (A) Alarm Output / 7
(B) Assistant
(C) Zoom out/8
(D) Zoom in/9
(E) Preset point setup/0 (F) USB
(G) ESC
(H) ScreenSwitch
(I) Record
(J) PTZ
(K) MainMenu
(L) Shift
(M) Power switch
Summary of APOLLO PRO DC LX
Page 1
Apollo pro dc lx 2 u 8 - 16 channel dvr user’s manual ®.
Page 2: Our Products Are Fully
Dont settle for less, all our products carry logos enhance your dvr with our wide range of cameras our products are fully tested to work together eyeball domes vandal domes p400 cameras ptz cameras internal domes mini cameras.
Page 3: Directory
3 directory 1 welcome ...................................................................................... 5 2 open-package check and cable connections ....................................6 2.1 initial check ............................................................6 2.2 hard disk installation ....
Page 4
4 4.4 system .............................................................................33 4.4.1 general ........................................................................33 4.4.2 encode .........................................................................34 4.4.3 network ..................
Page 5: 1. Welcome
5 1. Welcome thank you for purchasing our dvr! This manual is designed to be a reference tool for the installation and operation of your qvis dvr series dvr system. Youwillfindinformationaboutthisqvisdvrseriesdvr'sfeaturesandfunctions, as well as a detailed menu tree. Before you begin installation a...
Page 6
6 2 initial check and cable connections 2.1 initial check whenyoufirstreceiveyourdvr,pleasecheckthefollowing: 1. Please check whether there is any visible damage to the package appearance. The protective materials used for the package of the dvr can protect the dvr against most accidental damage dur...
Page 7
7 5). Connect sata data wire 6). Connect the power wire 7). Put the top back on 8). Screw on the cover 2.3 rack mount installation thisseriesofdvrisinastandard2ucase,soitcanberackmounted. Step: 1. Make sure the room temperature is lower than 35°c (95°f) 2.Keepatleast15cmspacearoundthedvrtoallowairto...
Page 8
8 front panel function table serial no key mark function 1 direction inthemenu,pressupordowntomovecursor changeconfigurationinthedrop-downmenu pressupordowntoselectrecordfileintheplayback status inthepreviewscreen,pressupordowntogointo 1/4/8/9/16 multiple channels screen inthemenu,pressleftorrightto...
Page 9
9 2.6 audio and video input and output connections 2.6.1 video input connections the video input port is a bnc connector plug. The type of input signal is pal/ ntscbnc(1.0vp-p,75Ω). The video signal must be of the correct standard and have a high signal to noise ratio,lowaberrationandlowinterference...
Page 10
10 2.6.4 audio signal output commonly the output parameter of a dvr audio signal is greater than 200mv 1kΩ(bnc)whichcanconnectalowimpedanceearphoneandactivesoundbox orotheraudiooutputequipmentsthroughapoweramplifier.Ifthesoundboxand thetonearmcannotbeisolated,ahowlingphenomenaisoftenexperienced. Her...
Page 11
11 (1,6,8)alarminput(2,7)grounding(3)alarm(5)rs485(4)rs232 parameter meaning g grounding (earth) c1,no1 alarm output interface(constant open type) t,r rs232 port a,b 485 communication interface which is connected with the recording control equipments such as the decoder 2.7.1 alarm input port specif...
Page 12
12 2.7.3 alarm output port relay parameters type:jrc-27f interface material silver rating (resistance load) rating switch capacity 30vdc2a,125vac1a maximalswitchpower 125va 160w maximalswitchvoltage 250vac,220vdc maximalswitchcurrent 1a isolation homo-polarityinterface 1000vac 1minute inhomo-polarit...
Page 13: 3 Basic Operation
13 3 basic operation note: the button in gray display indicates nonsupport. 3.1 turn on plug in and turn on the power supply switch. If the power supply indicator light lights up then the video recorder has turned on. After startup you will hear a beep. The default setting of the video output is a m...
Page 14
14 picture 3.1 system login password protection: if the password is entered continuously wrong for three times, the alarm will start. If the password is continuously wrong five times, the account will be locked. (through a reboot or after half an hour, the account can be unlocked automatically). For...
Page 15
15 picture 3.2 shortcut menu 3.5.1 main menu whenyoulogin,thesystemmainmenuisshownasbelow. Picture 3.3 main menu.
Page 16
16 3.5.2 playback therearetwomethodsforyoutoplaythevideofilesintheharddisk. 1). In the desktop shortcut menu. 2).Mainmenu>record->playback note: the hard disk that saves the video files must be set as read-write or read- only state. (4.5.1) picture 3.4 video playback 1).Listedfiles 2). File informat...
Page 17
17 detect: detect the storage connected with the dvr such as hard disk or universal disk. Erasure:choosethefiletodeleteandclickerasuretodeletethefile. Stop: stop the backup. Backup:clickbackupbuttonandthedialogboxispoppedup.Youcanchoose thebackupfileaccordingtothetype,channelandtime. Picture 3.6 rec...
Page 18
18 button function button function / play/pause backward stop slow play fast play previous frame nextframe previousfile nextfile circulation full screen table 3.2 playback control key note: frame by frame playback is only performed in the pause playback state. (operation hint) display the function o...
Page 19
19 3.5.4 alarm output pleasecheckcurrentchannelstatus:“o”meansitisnotinalarmingstatus,“ • ” means it is in alarming status. You can use desktop shortcut menu or click [main menu]> [alarm function]> [alarm output] to enter the alarm output interface. Picture 3.9 alarm output (configuration)alarmisona...
Page 20
20 speed:settheptzrotationrange.Defaultrange:1~8. Zoom:click/buttontoadjustthezoommultipleofthecamera. Focus:click/buttontoadjustthefocusofthecamera. Iris:click/buttontoadjusttheirisofthecamera. Direction control:controltheptzrotation.8directionscontrolissupportive. (4 directions in front panel is s...
Page 21
21 picture 3.12 ptz control 2: cruise between points a ptz camera can be set to cruise between a series of preset points. This is called acruise.Tosettheptzuptodothisisasfollows: 1). Cruise between points settings acruiselineisasetupofmultiplepresetconnectedpoints,thesetupprocedure isasfollows: step...
Page 22
22 3: scan the ptz can also work on the preset scan line repeatedly. 1). Scan setup step 1: inpicture3.10,clickthesetupbutton,whichtakesyoutopicture3.14; step 2: clickthepatternbuttonandinputapatrolvalueinthepatternvalue blank; step 3: clickthebeginbuttonandenterpicture3.10,hereyoucansetthe followin...
Page 23
23 2). Boundary scan calls inpicture 3.10,click thepageshiftbutton toentertheptzcontrol menuasshown inpicture3.12.Pleaseinputthenumberofthescaninthevalueblank,thenclickthe autoscanbutton,theptzwillbegintoworkonthescanline.Clickthestopbuttontostop. 5: rotating the horizontal click the horizontally ro...
Page 24
24 3.5.7 output adjust adjust tv output area parameters. You can use the desktop shortcut menu or enter [main menu]> [management tools]> [output adjust]. Picture 3.19 output adjust 3.5.8 logout tologout,shutdownthesystemorrebootthesystem.Youcanusethedesktop shortcut menu or enter [main menu]. Pictur...
Page 25: 4 Main Menu
25 4 main menu 4.1 main menu navigation main menu sub menu function record config settherecordingconfiguration,recordingtype,recording time section playback setrecordinglook-up,recordingplay,videofilestorage backup detectorformatbackupequipment,backtheselectivefiles snapshot storage setpresnapshot,r...
Page 26
26 main menu sub menu function management tools hard disk management setappointedharddiskasread-writedisc,read-onlydisc orredundantdisc,cleardata,resumedateandsoon user management modifyuser,teamorpassword.Adduserorteam.Delete user or team. Online user break the connection with the already login use...
Page 27
27 (prerecord)record1-30secondsbeforetheaction.(timelengthisdecidedby the code stream) (record mode)setthevideostate:schedule,manualorstop. Schedule:recordaccordingtothesetvideotype(common,detectionandalarm) and time section. Manual:clickthebuttonandtherelevantchannelwillstartrecordingnomatter what ...
Page 28
28 manual: no matter what the present channel is doing, once you choose the "manual"button,itwillonlytakeasnapshotwhenyoutellitto. Stop: nomatterwhatthepresentchannelisinastate,onceyouchoosethe "stop"button,itwillstopthesnapshotfunction. (period)setnormalrecordperiod,(setsthefrequencythatasnapshotis...
Page 29
29 remove:clearthefileinformation. Add:showthefileinformationtosatisfythesetfileattributes. Start/pause:clicktheplaybuttontostartthebackupandclickthepausebutton to stop the backup. Cancel:duringbackupyoucanexitthepagelayouttocarryoutotherfunctions. 4.3 alarm function alarmfunctionsinclude:motiondete...
Page 30
30 (period) trigger the motion detect signal in the set time section. You can set according to week or set uniformly. Each day is divided into four time sections. Means the setup is valid. Picture 4.6 set the time section (interval) only one alarm signal is turned on even if there are several motion...
Page 31
31 (send email) means sending an email to the user when the alarm is turned on. Note:setinthe[netservice]andsendemail. (buzzer) buzzering when alarm is actived (ftp upload)uploadrecordfiletoftpserverwhenalarmisactived note: set in the [netservice] and send ftp. 4.3.2 video blind whenthevideoimageisi...
Page 32
32 4.3.4 alarm input whenthesystemgetsanexternalalarmsignal,thealarmfunctionisturnedon. Picture 4.11 alarm input setmethod:refertochapter4.3.1.Motiondetect note:"advanced" button is the same as right-click. 4.3.5 alarm output refer to chapter 3.5.4. 4.3.6 abnormal analysing and inspecting current so...
Page 33
33 4.4 system setup setthesystemparameterssuchasgeneral,encode,network,netservice, guidisplay,ptzconfig,rs232andtoursetup. 4.4.1 general picture 4.13 general setup (system time) set the system data and time. (date format)choosethedataformat:ymd,mdy,dmy. (date separator) choose list separator of the ...
Page 34
34 4.4.2 encode setup setthevideo/audiocodeparameters:videofile,remotemonitoringandsoon. Seteveryindependentchannel’scodingparameterintheleftpart,andsetthe combine encode parameter in the right part. Note:combineencodeintroducesvideocompressiontechniquewhichcombines andcompressesmulti-channel’svideo...
Page 35
35 4.4.3 network setup picture 4.17 network (net card) you can choose cable network card or wireless network card. (dhcp enable) obtain ip address automatically (not suggested) note:dhcpserverispreinstalled. (ip address)settheipaddress.Default:192.168.1.10. (subnet mask)setthesubnetmaskcode.Default:...
Page 36
36 (pppoe setup) picture 4.19 pppoe input the user name and password that the isp (internet service provider) provides. After saving it reboot your system. Then the dvr will build a network connection based on pppoe. The ip address will change into a dynamic ip address after the above operation is d...
Page 37
37 (email setup) ifthealarmisturnedonorthealarmlinkagephotosaretaken,thesystemcan send an email of the alarm information and the photos to an appointed address. Picture 4.21 email smtp server:emailserveraddress.Thiscouldbeanipaddressoradomain name.Adomainnamecanonlybeusedifithasthecorrectdnsconfigur...
Page 38
38 (ddns) (dynamic domain name server). Local domain name:insertthedomainnameregisteredbytheddns. User name:inserttheusername. Password:insertthepassword. When the ddns is successfully configured and started, you can connect the domain name in the ie address column to visit. Note:thednssetupmustbeco...
Page 39
39 (arsp) startup ddns server to add devices and manage it in the ddns server type:choose"dns" enable: means it is chosen severip:ipaddressofddnsserver port: (wireless config)adslthrough3gnetcard,usecmstovisitandconfigthedevice picture4.25wirelessconfig (enable) choose enable to make all settings a...
Page 40
40 (enable) select this to make sure the abnormal function is working (port) this is the port to enable mobile monitoring. You will need to make a router map of it if you want to view everything by mobile (upnp)upnpprotocolcansetautoportforwardingontherouter,makesure upnp is running on the router be...
Page 41
41 4.4.5 gui display configurethevideooutputparametersincludingthefrontoutputmodeandcode output mode. Front output:inthelocalpreviewmodeandincludes:channeltitle,timedisplay, recordstatus,alarmstatus,bitrateinfo,transparencyandregioncover. Code output:inthenetworksurveillanceandvideofilemodeinclude:c...
Page 42
42 4.4.6 ptz setup picture 4.29 ptz setup (channel) choose the dome camera input channel. (protocol)choosethecorrespondingdomeprotocol.(pelcodasanexample) (address) set as the corresponding dome address. Default:1. (note:theaddressmustbeconsistentwiththedomeaddress.) (baud rate) choose the correspon...
Page 43
43 4.4.8 tour setup set the patrol display. means that the tour mode is turned on. You can choose thesinglewindow,fourwindows,ninewindows,sixteenwindowspatroldisplay or single display. Picture 4.31 tour setup (interval)setthepatrolswitchinterval.Thesetrangeis5-120seconds. Note:/meansturnoff/onthep...
Page 44
44 4.5.2 account manage the user purview. Note: 1.Themaximumcharacterlengthis8bytesforthefollowinguserand user team name. A blank ahead of or behind a character string is invalid. A middle blank in the character string is valid. Legal charactersinclude:letters,numbers,underline,subtractionsign,dot. ...
Page 45
45 (add user) to add a user to the team and set the user authority. Enter the menu interface and input the user name and password. Choose the team and choose whether cover using is to be activated. Cover using means that the account can be used by multiple users at the same time. Onceyouchoosethetea...
Page 46
46 4.5.3 online user look up the network user information in the local dvr. You can choose the networkuserandcuttheconnection.Thentheuserislockeduntilnextboot- strap. Picture 4.38 online user 4.5.4 tv adjust refer to chapter 3.5.7. 4.5.5 auto maintain theusercansettheautoreboottimeandautofiledeletin...
Page 47
47 4.5.7 upgrade picture 4.41 upgrade (upgrade) choose usb interface. (upgrade file)choosethefilewhichneedsupgraded. 4.5.8 device info providedeviceinterfaceinfolikeaudioin,alarmin/outtobeconvenientlyused for user. Picture 4.42 device info. 4.6 info 4.6.1 hdd info displaytheharddiskstate:harddisktyp...
Page 48
48 clue: means that the hard disk is normal. X means that the hard disk is not working. - means that there is no hard disk. If the user needs to change the damaged hard disk then you must shut down the dvr and remove all the damaged hard disks before installing a new one. * behind serial number me...
Page 49
49 4.6.4 version display the basic information such as hardware information, software edition, issue data and so on. Picture 4.46 version 4.7 shut down system refer to chapter 3.5.8..
Page 50: 5 Faq and Maintenance
50 5 faq and maintenance 5.1 faq ifyourproblemsisnotlisted,pleasecontactyourlocalinstallerforservice. 1). The dvr does not boot up normally. Possible reasons are as followed: 1 the power supply is not correct. 2 switch power supply line is not in good connection. 3 switch power supply is damaged. 4 ...
Page 51
51 5). Real-time image problems such as the image color or the brightness distortion. Possible reasons are as followed: 1 whenusingthebncoutput,theoptionbetweenthenmodeorpal mode is wrong and the image becomes black and white. 2 the dvr is not matched the monitor impedance. 3 the video transmission ...
Page 52
52 11). The dvr can not control the ptz. Possible reasons are as followed: 1 there is something wrong with the frontal ptz. 2 thesetting,connectionortheinstallationoftheptzdecoderisnot correct. 3 the connections are not correct. 4 the ptz setting of the dvr is not correct. 5 the protocols of the ptz...
Page 53
53 15). Network connection is unstable. Possible reasons are as followed: 1 network is not stable. 2 ipaddressisconflicted. 3 macaddressisconflicted. 4 the net card of the dvr is bad. 16). There is something wrong with the usb backup or writing a cd. Possible reasons are as followed: 1 the rewritabl...
Page 54
54 21). The storage time is not enough. Possible reasons are as followed: 1 front monitor quality is bad. The lens is too dirty. The monitor is in back lighting installation. 2 the hard disk capability is not enough. 3 the hard disk is damaged. 22). The downloading files can not play. Possible reaso...
Page 55: Appendix 2.Mouse Operation
55 appendix 1.Remote controller operation serial number name function 1 multi-windowbutton samefunctionasmulti-windowbuttoninthefrontpanel 2 numeric button code input/number input/channel switch 3 (esc) same function as (esc) button in the front panel 4 direction button same function as direction bu...
Page 56
56 appendix 3.Technique parameters type 8ch 16ch system main processor high performance embedded microprocessor operation system embedded linux operation system system resource synchronousmulti-channelrecording,synchronousmulti- channelsub-codestream,synchronousmulti-channel playback,synchronousnetw...
Page 57
57 type 8ch 16ch other power supply 12v/6aexternalpowersupply power consumption working temperature 0ºc~55ºc working humidity 10%–90% air pressure 86kpa–106kpa size 442x430.1x91mm weight 7.5kg (without hard disk) installation desktop general features • 8/16channelvideoinputs&8/16simultaneousplayback...