1. DL manuals
  2. Qvis
  3. Security Camera
  4. HDCVI-EYE1
  5. User Manual

Qvis HDCVI-EYE1 User Manual

Manual is about: 1 Megapixel HDCVI Bullet

Summary of HDCVI-EYE1

  • Page 1

    Hdcvi-mb1 hdcvi-eye1 1 megapixel hdcvi bullet & dome cameras user’s manual v1.0 06 / 2014.

  • Page 2

    I.

  • Page 3: Welcome

    Ii welcome thank you for purchasing either the hdcvi bullet or eyeball dome cameras. This user’s manual is designed to be a reference tool for the installation and operation of your camera setup. Here you can find information about the corresponding hdcvi camera’s features and functions, as well as ...

  • Page 4

    Iii important safeguards and warnings 1 ．electrical safety  all installation and operation here should conform to your local electrical safety codes.  the power supply shall conform to the requirement in the selv (safety extra low voltage) and must make sure that the limited power source is rated ...

  • Page 5

    Iv  please make sure the ccd (cmos) component is away from the radiation of the laser beam device. Otherwise it may result in ccd (cmos) optical component damage.  it is recommended that the grounding studs of the product should be grounded, so to further enhance the reliability of the camera. 6. ...

  • Page 6: Table Of Contents

    V table of contents 1 general introduction..........................................................................................................1 1.1 overview...................................................................................................................1 1.2 features............

  • Page 7

    © copyright qvis ®. All documentation rights reserved. 1 1general introduction 1.1overview our megapixel hd camera conforms to the hdcvi standard. It supports high speed transfer of video signals over long distance transmissions without any delay. It can be controlled by a dvr that also conforms to ...

  • Page 8

    © copyright qvis ®. All documentation rights reserved. 2 auto gain function this outputs the standard video signal under different illumination environments. The amplifier can automatically adjust within a wide range. The system can enhance the camera sensitivity in low illumination and enhance the ...

  • Page 9

    © copyright qvis ®. All documentation rights reserved. 3 1.4specifications 1.4.1 performance please refer to the following sheet for network camera performance specification: parameter hdcvi-mb1 hdcvi-eye1 video processor 1/2.9" 1.0 mega pixels cmos video format pal/ntsc effective pixel 1280 (h) x 7...

  • Page 10

    © copyright qvis ®. All documentation rights reserved. 4 2framework & dimensions 2.1hdcvi-mb1 please refer to the following figures for dimension information. The unit is mm. See figure 2-1 and figure 2-2. Figure 2-1 figure 2-2 please refer to the following sheet for detailed information. Sn name fu...

  • Page 11

    © copyright qvis ®. All documentation rights reserved. 5 2.2 hdcvi-eye1 please refer to the following figure for dimension information. The unit is mm. See figure 2-3 and figure 2-4. Figure 2-3 figure 2-4 sn name function 1 ir lights these are to send out the ir compensation light to enhance the nig...

  • Page 12

    © copyright qvis ®. All documentation rights reserved. 6 3installation important: please make sure the installation surface can support a minimum of 3x weight of the camera and the bracket. 3.1 hdcvi-mb1 (bullet camera) step 1: drill three holes into the installation surface (wall or the ceiling). I...

  • Page 13

    © copyright qvis ®. All documentation rights reserved. 7 figure 3-2 step 4: connect the device’s video output port to the dvr device. Then connect the power cable to the device. Now you have completed the device installation and cable connection. You can use the terminal encoding device to monitor t...

  • Page 14

    © copyright qvis ®. All documentation rights reserved. 8 figure 3.3 step 3 adjust the lens to get the clearest monitor video quality. See figure 3-4. Use a crosshead screwdriver to loosen the screw and the turn the camera body to the proper position manually. Fix the screw again. Important: do not r...

  • Page 15

    © copyright qvis ®. All documentation rights reserved. 9 step 4 line up the bulge of the decoration ring to the nick found on the camera body and install along the tilt installation. Push and then turn decoration ring clockwise. The installation is complete after you secure the decoration ring. You ...

  • Page 16

    © copyright qvis ®. All documentation rights reserved. 10 for more information about our other analogue cameras and other available hdcvi equipment, dvrs, nvrs & accessories, please visit our website: www.Adata.Co.Uk alternatively scan this qr code with your smart phone to be directed instantly to o...