1. DL manuals
  2. Qvis
  3. Security Camera
  4. IPTZ-P400-10X
  5. User Manual

Qvis IPTZ-P400-10X User Manual

Manual is about: 2MP IR MINI PTZ CAMERA

Summary of IPTZ-P400-10X

  • Page 1

    © copyright qvis ®. All documentation rights reserved. 2mp ir mini ptz camera iptz-p400-10x v 1.0 08.2015 user manual.

  • Page 2

    © copyright qvis ®. All documentation rights reserved..

  • Page 3: Welcome

    © copyright qvis ®. All documentation rights reserved. Welcome thank you for purchasing the 2mp ir mini ptz camera . This user ’s manual is designed to be a reference tool for the installation and operation of your system. Here you can find information about the corresponding ip camera ’s features a...

  • Page 4: Precautions

    © copyright qvis ®. All documentation rights reserved. Precautions 1 ． electrical safety all installation and operation here should conform to your local electrical safety codes. The power supply shall conform to the requirement in the selv (safety extra low voltage) and must make sure that the limi...

  • Page 5

    © copyright qvis ®. All documentation rights reserved. Do not allow the water and other liquid to penetrate into the device if casing has been compromised. This series product complies with the ip66 standard specified in the degrees of protection provided by enclosure. Ensure lightning surge protect...

  • Page 6: Table Of Contents

    © copyright qvis ®. All documentation rights reserved. Table of contents 1 general and technical features......................................................................................... 1 1.1 special features ……………………………………………….. ....................................... 1 1.2 function introd...

  • Page 7

    © copyright qvis ®. All documentation rights reserved. 3 osd menu function ................................................................................................................ 37 3.1 information.................................................................................................

  • Page 8

    © copyright qvis ®. All documentation rights reserved. 1 1. General and technical features 1.1 special features high definition footage shoot video footage using mpeg h.264 compression at varying frame rates, which allows you to save network bandwidth without compromising on footage quality. You wil...

  • Page 9

    © copyright qvis ®. All documentation rights reserved. 2 1.2 function introduction infinitely variable speed, softened zoom and automatic speed matching technology lowest manual operational movement speed:0.01º/s, fastest manual operational movement speed with precise positioning: 12º/s 256 tour pre...

  • Page 10

    © copyright qvis ®. All documentation rights reserved. 3 1.5 preset position set up and call up within the preset function the camera stores the current pan/tilt angle, zoom, and other position parameters into memory. When necessary the camera recalls these parameters and adjusts the camera to a par...

  • Page 11

    © copyright qvis ®. All documentation rights reserved. 4 1.9 technical parameters 1.10 osd menu operation call up osd menu call preset 95 to enter the main osd menu; call preset 96 to close the osd menu or select ‘exit’ confirm the ‘left ‘and ‘right ‘button is controlled by ptz can change the requir...

  • Page 12

    © copyright qvis ®. All documentation rights reserved. 5 2. Web browser operation guide 2.1 common operations 2.1.1 factory settings an ip camera is classified as a type of network equipment, you need to configure its network ip address, gateway, and other information to fit within the network it is...

  • Page 13

    © copyright qvis ®. All documentation rights reserved. 6 to find the ‘cmd’ console in windows, firstly search for ‘cmd’ on your computer, the icon for it should look like this: once loaded, the format of the command needs to be: ping 192.168.0.99 if the camera is correctly setup and connected the cm...

  • Page 14

    © copyright qvis ®. All documentation rights reserved. 7 2.2 web login 2.2.1 login open up web browser within the windows interface, enter default factory ip address (192.168.0.99) to open the camera’s web interface. A dialog box will be shown as follows: user name ： admin password ： admin port ： de...

  • Page 15

    © copyright qvis ®. All documentation rights reserved. 8 after you have installed the plug-in; input user name, code, and then click the ‘login ‘button to enter the ‘preview ‘screen. See 2.2.2-2 picture 2.2.2-2 preview screen picture 2.2.2-1 plug-in installation sheet 2.2.2-3 preview screen informat...

  • Page 16

    © copyright qvis ®. All documentation rights reserved. 9 sheet 2.2.2-4 ptz control screen information in the preview scr een, you can control the camera’s streamed video, which includes control over video recording, snapshot, intercom, and the on/off of the sound. The size of the image can be adjust...

  • Page 17

    © copyright qvis ®. All documentation rights reserved. 10 operation methods for pattern scanning 1. Enter the pattern scan screen, it will show the current pattern scan path. See 2.2.2-5 2. Start recording the scanning; click start to record the pattern scan, and the start using the camera direction...

  • Page 18

    © copyright qvis ®. All documentation rights reserved. 11 auto scanning setting enter the auto scan screen to set scan speed, left boundary, right boundary, start scan, and to stop scan. Auto scanning include 8 scanning paths. See 2.2.2-7 picture 2.2.2-8 auto scans settings 1. Scanning speed: from 1...

  • Page 19

    © copyright qvis ®. All documentation rights reserved. 12 picture 2.2.3-1 video playback note: playback function can only be used under the circumstance when the camera has an sd card installed. If the camera has sd card, and it is using it for the first time you must click the ‘storage’ key to init...

  • Page 20

    © copyright qvis ®. All documentation rights reserved. 13 2.2.5 configuration 2.2.5.1 parameter configuration click ‘configuration’, enter configuration interface. To set local configuration select ‘local configuration from the options list on the right side of the screen, as shown in picture 2.2.5-...

  • Page 21

    © copyright qvis ®. All documentation rights reserved. 14 2.2.5.2 system system → device information in device information screen, users can set the device name, model, serial no., firmware version, encoding version, number of channels, number of hdds, and number of alarm input and output. See pictu...

  • Page 22

    © copyright qvis ®. All documentation rights reserved. 15 picture 2.2.5-4 time settings system→ maintenance enter system maintenance interface, see picture 2.2.6-5. Click ‘reboot’ to reboot the device. Click ‘restore’ to restore device parameters. It will easily restore the other parameters except i...

  • Page 23

    © copyright qvis ®. All documentation rights reserved. 16 picture 2.2.5-5 system maintenance interface 2.2.5.3 network network → tcp/ip in the ‘tcp/ip’ screen, users can set ‘ipv4 address’,’ipv4 subnet mask ’,’ipv4 default gateway’,’ipv4 dns server’, and ’ipv4 mode’. When ticking ‘auto’, the device ...

  • Page 24

    © copyright qvis ®. All documentation rights reserved. 17 system → port ‘port’ screen includes: ‘http port’ (the default is 80), ‘rtsp port’ (the default is 554), and ‘https port’ (the default is 443). Through network access to the device, users can set the corresponding port. After modifying the pa...

  • Page 25

    © copyright qvis ®. All documentation rights reserved. 18 network →pppoe tick ‘enable pppoe’, this enables the pppoe function. Input the pppoe user name and pppoe password, click ‘save’ and restart camera. Camera will now gain a public ip address. After modifying the related parameters, need to clic...

  • Page 26

    © copyright qvis ®. All documentation rights reserved. 19 picture 2.2.5-10 ftp setting network → upnp tick ‘enable upnp’ and this function will make the device to be automatically located within the lan. For a camera located within an internal network the upnp function will make a gateway or instruc...

  • Page 27

    © copyright qvis ®. All documentation rights reserved. 20 network → email enter email settings, you will to fill in the following details; sender, sender address, smtp server , smtp port, tick start ssl or authentication, user name, password & password confirm, receiver, and receiver address, see pi...

  • Page 28

    © copyright qvis ®. All documentation rights reserved. 21 network → port mapping tick ‘enable port mapping’ to automatically open port, see picture 2.2.5-14 sheet 2.2.5-14 audio settings network → wifi to enable wifi connection you need to input wifi connection parameter s in to the relevant input f...

  • Page 29

    © copyright qvis ®. All documentation rights reserved. 22 2.2.5.4 audio/video audio/video → video enter ‘video’ setting screen, these options will allow the user to set camera stream type, resolution, bitrate type, etc. See picture 2.2.6-16, video settings detailed information, see picture 2.2.5-17....

  • Page 30

    © copyright qvis ®. All documentation rights reserved. 23 after modifying the related parameter you need to click ‘save’ to save settings. See picture 2.2.5-18 for the audio configuration interface, audio configuration parameters shown in picture 2.2.5-19 note: after modifying audio encoding, please...

  • Page 31

    © copyright qvis ®. All documentation rights reserved. 24 picture 2.2.5-20 roi 2.2.5.5 image image → display settings enter the image configuration interface, see picture 2.2.5-21, image configuration illustration see sheet 2.2.5-22 picture 2.2.5-21 display settings.

  • Page 32

    © copyright qvis ®. All documentation rights reserved. 25 sheet 2.2.5-22 image parameters ‘sharpness ‘: the higher the value, the clearer the image edge will be. Although if you raise the sharpness value, it may make the picture look distorted. ‘focus mode:’ in ‘auto’ mode, the device automatically ...

  • Page 33

    © copyright qvis ®. All documentation rights reserved. 26 ‘mirror’ : direction of symmetry includes ‘left/right’, ‘up/down’, center. The video adjustment option is used to switch symmetry direction of image. ‘wdr’ : on/off ‘white balance’ : auto/mwb ‘digital noise reduction’ : this is used to adjust...

  • Page 34

    © copyright qvis ®. All documentation rights reserved. 27 image → text overlay camera supports text overlay within the image. Supports a maximum of 40 characters, see picture 2.2.5-24. Input the text overlay characters into box, and then tick corresponding character number. The user can preview the ...

  • Page 35

    © copyright qvis ®. All documentation rights reserved. 28 2.2.5.6 safety safety → user enter the safety configuration menu; the user can set user information, select administrator ‘admin’, and also create other user accounts according to how many users will have access to the camera. A maximum of 8 ...

  • Page 36

    © copyright qvis ®. All documentation rights reserved. 29 picture 2.2.5-28 modify user security → rtsp authentication the authentication can be set as either ‘disable’ or ‘basic’ from the drop down list options. ‘disable’ : closes rtsp authentication. ‘basic’ : enables rtsp authentication. After mod...

  • Page 37

    © copyright qvis ®. All documentation rights reserved. 30 camera web interface. When the user logs in as anonymous they will only have access to the live preview video footage from the camera. The will not have access to the playback, log, and configuration interface. See picture 2.2.5-30. When you ...

  • Page 38

    © copyright qvis ®. All documentation rights reserved. 31 picture 2.2.5-31 ip address filter event → motion detection area setting: hold down left mouse key and drag it across the live preview footage window, then release mouse left key, this will finish drawing the area. When user finishes drawing ...

  • Page 39

    © copyright qvis ®. All documentation rights reserved. 32 click [edit] to edit the arming schedule for the whole week or for selected days within the week. User can also set start time and end times for four specific periods per day, see picture 2.2.5-33. Picture 2.2.5-33 arming schedule/linkage met...

  • Page 40

    © copyright qvis ®. All documentation rights reserved. 33 slider sensitivity scale (‘sensitivity): 0-100 after related parameter has been revised, click [save] to save related settings. Picture 2.2.5-34 video tampering event → exception ‘exception type’ includes ‘hdd full ‘, ‘hdd error’, ‘network di...

  • Page 41

    © copyright qvis ®. All documentation rights reserved. 34 storage → record schedule tick the ‘enable record schedule’, then click ‘editor’ button to edit the record schedule. Appoint record period(s) and the choose record type. See picture 2.2.5-36. For edit schedule, see picture 2.2.5-37. Record ti...

  • Page 42

    © copyright qvis ®. All documentation rights reserved. 35 picture 2.2.5-37 edit schedule storage → storage management storage management menu is used to view the status and the capacity of the storage medium. You can also carry out format operations on the storage medium. Select the inserted tf card...

  • Page 43

    © copyright qvis ®. All documentation rights reserved. 36 storage → capture setup snapshot capture to coincide with the record schedule’s parameters. See picture 2.2.5-39. ‘format’ provides the option to capture snapshot in the jpeg image format. ‘resolution’ is current main stream’s resolution. ‘qu...

  • Page 44: 3   Osd Menu Function

    © copyright qvis ®. All documentation rights reserved. 37 3 osd menu function the osd (on screen display) menu of the camera can be viewed either within the live footage preview screen on the web connection interface or via a display monitor connected to an nvr that has a connection to the camera. Y...

  • Page 45

    © copyright qvis ®. All documentation rights reserved. 38 3.2 language main menu information [camera] image motion restart default exit [language] ir led idle mask alarm ptz display back exit camera the user can choose and set osd menu language. The device supports either chinese/english. Location a...

  • Page 46

    © copyright qvis ®. All documentation rights reserved. 39 3.3 ir led information [ camera ] image motion restart default exit main menu language [ ir led ] idle mask alarm ptz display back exit camera [illumination 34] mode auto sensitivity 4 switch delay 5 near power 10 far power 10 near compensati...

  • Page 47

    © copyright qvis ®. All documentation rights reserved. 40 3.4 idle information [ camera ] image motion restart default exit main menu language ir led [ idle ] mask alarm ptz display back exit camera action off delay 10min back exit idle user could set camera to idle via the ‘camera’ osd menu options...

  • Page 48

    © copyright qvis ®. All documentation rights reserved. 41 3.5 mask information [ camera ] image motion restart default exit main menu language ir led idle [ mask ] alarm ptz display back exit camera [mask no. 1] enable off mask set back exit mask camera supports mask protection, supports a maximum o...

  • Page 49

    © copyright qvis ®. All documentation rights reserved. 42 3.6 alarm information [ camera ] image motion restart default exit main menu language ir led idle mask [ alarm ] ptz display back exit camera input mode n/o alarm mode off action off alarm out off reset delay 30sec back exit alarm camera supp...

  • Page 50

    © copyright qvis ®. All documentation rights reserved. 43 3.7 ptz display information [ camera ] image motion restart default exit main menu language ir led idle mask alarm [ptz display] back exit camear camera supports ptz function, ptz display includes on/off option. Method as follows: click up/do...

  • Page 51

    © copyright qvis ®. All documentation rights reserved. 44 3.8 image information camera [ image ] motion restart default exit main menu [image adjustment] exposure focus wdr white balance image enhancement video adjustment default back exit image [brightness 50] contrast 50 saturation 50 sharpness 50...

  • Page 52

    © copyright qvis ®. All documentation rights reserved. 45 3.9 exposure information camera [ image ] motion restart default exit main menu image adjustment [ exposure ] focus wdr white balance image enhancement video adjustment default back exit image [mode auto] iris f2.0 shutter 1/25 gain 50 exposu...

  • Page 53

    © copyright qvis ®. All documentation rights reserved. 46 3.10 focus information camera [ image ] motion restart default exit main menu [imageadjustment] exposure [ focus ] wdr white balance image enhancement video adjustment default back exit image focus mode auto focus distance 1.5m back exit focu...

  • Page 54

    © copyright qvis ®. All documentation rights reserved. 47 3.11 wdr information camera [ image ] motion restart default exit main menu image adjustment exposure focus [ wdr ] white balance image enhancement video adjustment default back exit image [wdr off] level 0 back exit wdr camera supports wdr (...

  • Page 57

    © copyright qvis ®. All documentation rights reserved. 50 3.14 image adjustment information camera [ image ] motion restart default exit main menu image adjustment exposure focus wdr white balance image enhancement [video adjustment] default back exit image [mirror off] back exit video adjustment ‘v...

  • Page 58

    © copyright qvis ®. All documentation rights reserved. 51 3.15 default information camera [ image ] motion restart default exit main menu image adjustment exposure focus wdr white balance image enhancement video adjustment [ default ] back exit image restore default settings ？ [ ok ] cancel default ...

  • Page 59

    © copyright qvis ®. All documentation rights reserved. 52 3.16 scan information camera image [ motion ] restart default exit main menu [ scan ] sequence pattern back exit motion [scan no. 1] scan speed 14 left limit set right limit set scan start back exit scan auto scan function is for repeated aut...

  • Page 60

    © copyright qvis ®. All documentation rights reserved. 53 3.17 sequence information camera image [ motion ] restart default exit main menu scan [ sequence ] pattern back exit motion [sequence no. 1] start preset 1 stop preset 10 duration 5sec sequence start back exit motion auto sequence sets device...

  • Page 61

    © copyright qvis ®. All documentation rights reserved. 54 3.18 pattern information camera image [ motion ] restart default exit main menu scan sequence [ pattern ] back exit motion [pattern no. 1] pattern set pattern delete pattern start back exit pattern the pattern function means the camera can op...

  • Page 62

    © copyright qvis ®. All documentation rights reserved. 55 3.19 restart information camera image motion [ restart ] default exit main menu restart system [ ok ] cancel restart camera allows user to remotely restart the system via the osd menu. Operation method: open osd menu, click up/down to ‘restar...

  • Page 63

    © copyright qvis ®. All documentation rights reserved. 56 3.20 default information camera image motion restart [ default ] exit main menu [ restore ] default back exit default setting reset settings, except ip [ ok ] cancel restore camera default function restores all modified camera parameters to d...

  • Page 64

    © copyright qvis ®. All documentation rights reserved. 57 for more information about our ip cameras and other available cameras, nvrs & accessories, please visit our website: www.Adata.Co.Uk alternatively scan this qr code with your smart phone to be directed instantly to our website:.