1. DL manuals
  2. RACOM
  3. Wireless Router
  4. M!DGE
  5. Operating Manual

RACOM M!DGE Operating Manual

Manual is about: GPRS/EDGE/UMTS routers

Summary of M!DGE

  • Page 1

    Operating manual . Gprs/edge/umts routers m!Dge, mg102 . 1.1 11/16/2011 www.Racom.Eu racom s.R.O. • mirova 1283 • 592 31 nove mesto na morave • czech republic tel.: +420 565 659 511 • fax: +420 565 659 512 • e-mail: racom@racom.Eu.

  • Page 3

    Table of contents introduction .......................................................................................................................................... 5 1. Product description ............................................................................................................

  • Page 4

    1.1. Mg model overview ..................................................................................................................... 6 1.2. M!Dges interfaces and status indicators ..................................................................................... 7 1.3. Pin assignment of s...

  • Page 5: Introduction

    Introduction thank you for purchasing m!Dge/mg102 wireless router from racom. This chapter gives you an in- troduction to m!Dge/mg102 wireless router. The following chapters describe the installation and the configuration. In next description is used the notation router instead of gprs/edge/umts rou...

  • Page 6: 1. Product Description

    1. Product description 1.1. The m!Dge – mg102 family the handling of the different mg models is very similar. All models run mg software which adapts itself to the mg hardware. The software will not allow you to configure options the hardware does not offer (e.G. Gps or digital i/o). The below table...

  • Page 7

    1.2. Product description m!Dge fig. 1.2: front panel and terminal panel of m!Dge the following table describes the meaning of the status indicators: tab. 1.2: m!Dges interfaces and status indicators function state color label the caption on the green side apply start up, maintenance solid green stat...

  • Page 8

    Please find the description of each interface in the following table: 1.2.1. Pin assignments screw terminal tab. 1.3: pin assignment of screw terminal signal pin v gnd 1 v1+ (12–48 v=) 2 v gnd 3 v2+ (12–48 v=) 4 rxd 5 txd 6 gnd 7 out1: dry contact relay normally open with m!Dge without powering 8 9 ...

  • Page 9

    1.3. Product description mg102 1.3.1. The front panel the front panel has 10 status indicators. In addition there are two sim card slots and a reset button at the front panel. Fig. 1.3: the front panel the following table describes the components on the front panel: 9 © racom s.R.O. – gprs/edge/umts...

  • Page 10

    Tab. 1.4: components on the front panel function state color label panel the device is powered on green power front power is missing off this indicates one of the following conditions: - the device is starting up - loading a new configuration - factory reset initiated by web manager blinking slowly ...

  • Page 11

    1.3.2. The back panel the back panel has the interfaces described in the table below: fig. 1.4: the back panel of 2009 model fig. 1.5: the back panel of 2010 model tab. 1.5: components on the back panel function state color label panel gps antenna connector impedance: 50 Ω connector: sma female mg10...

  • Page 12

    1.4. M!Dge/mg102 software all m!Dge/mg102 wireless routers run m!Dge/mg102 software. Software offers the following key features: • interfaces and connection management (section section 3.1.4, “interfaces”) ○ dial-out (on demand, permanent) ○ connection monitoring ○ fallback to backup profile or sim ...

  • Page 13

    1.5.1. Mobile internet access m!Dge/mg102 can be used for mobile internet access. Supported services include: • universal mobile telecommunications system (umts), high speed packet access (hspa) including hsdpa and hsupa • general packet radio service (gprs), enhanced data rates for gsm evolution (e...

  • Page 14: 2. Installation

    2. Installation 2.1. Environmental conditions the following precaution must be taken before installing m!Dge/mg102: • avoid direct solar radiation • protect the device from humidity, steam and aggressive fluids • grant sufficient circulation of air around m!Dge/mg102 • for indoor use only • temperat...

  • Page 15

    2.2.3. Installation of the gps antenna mg102 require passive gps antennas. The router needs to put the antenna with a good view of satellites. 2.2.4. Installation of the local area network up to four ethernet devices can directly be connected to the mg102, maximal two to m!Dge. 2.2.5. Installation o...

  • Page 16: 3. Configuration

    3. Configuration m!Dge/mg102 holds different configurations, such as the factory configuration and the user configur- ation. The user configuration can be modified by the user as follows: • using the forms on the web pages of web manager (chapter section 3.1, “configuration via the m!Dge/mg102 web m...

  • Page 17

    Description step please connect the ethernet interfaces of your computer and the m!Dge/mg102. 1. If not yet enabled, please enable the dynamic host configuration protocol (dhcp) so that your computer can lease an ip address from m!Dge/mg102. Wait a moment until your pc has re- ceived the parameters ...

  • Page 18

    3.1.3. Home this page gives you a system overview. It helps you when initially setting up device but also functions as dashboard during normal operation. Gprs/edge/umts routersm!Dge, mg102 – © racom s.R.O. 18 configuration.

  • Page 19

    3.1.4. Interfaces in the section the physical interfaces of m!Dge/mg102 are configured. Details for all enabled connec- tions are displayed on its own section appendix a, connectors and cables wan • link management fw 3.4 introduces a wan link manager. Depending on your hardware, you can choose from...

  • Page 20

    • link management – setings ip health check – this feature is prepared for switching between profiles or lines. Mg102 is checking availability of monitored host 1 (optionaly 2). If the host (hosts) is (are) not reachable the second profile (link) will be switched to. Note this functionality has a cl...

  • Page 21

    • maximum segment size the maximum segment size (mss) is the largest amount of data, specified in bytes, that a computer or communications device can handle in a single, unfragmented piece. For optimum communications, the number of bytes in the data segment and the headers must not add up to more th...

  • Page 22

    Combined mode (lan) mg102 ip address network ports 192.168.1.1 192.168.1.0/24 port 1, 2, 3, 4 mixed mode ( lan / wan) mg102 ip address network ports 192.168.1.1 192.168.1.0/24 port 1–3 (mg102) 192.168.2.1 192.168.2.0/24 port 4 (mg102) m!Dge uses two ethernet interfaces. It is possible set the same l...

  • Page 23

    • port settings for every ethernet port the link negotiation can be set. In most cases auto negotiation will work. • ip settings define the m!Dge/mg102 lan. Usually the first address within that lan is assigned to the router. Provide that ip address and net mask in dot-decimal notation or use the de...

  • Page 24

    ○ wan description parameter disabled means that the ip interface will be left unconfigured. Static configuration allows you to set the ip parameters. Dhcp means that the ip configuration will be retrieved automatically from an external dhcp server. Ip mode: enable or disable the pppoe connection sta...

  • Page 25

    Description parameter pppoe password password: specifies the service name set on the access concentrator. Leave it blank unless you have many services and need to specify the one you need to connect to. Service name: this may be left blank and the client will connect to any access concentrator. Acce...

  • Page 26

    Mobile • administration after the configuration (e.G. Setting the apn), the mobile connection is enabled here. We recommend using the ´pernament´ option. The umts/gsm led is blinking during the connection establishment and goes on as soon as the connection is up. See the troubleshooting section and ...

  • Page 27

    • configuration description parameter specify the sim card that shall be used for this profile. Sim used: set the phone number that is to dial. This should be *99***1# for packet services (gprs/umts). For isdn and csd connections use the phone number to dial. Phone num- ber: user name (get this info...

  • Page 28

    Description parameter enable or disable fixed ip address on the mobile interface. Enable specif- ic client ip ad- dress: specify a fixed client ip address on the mobile interface. Specific client ip address: specifies the condition for a profile switch to the other profile. Primary profile profile s...

  • Page 29

    • sim this section lets you store the pin code. With the correct pin code deposited you will be able to enable or disable pin protection. M!Dge/mg102 can only read sim cards if the correct pin code is provided or if pin protection is disabled. It is not recommended to disable pin protection since a ...

  • Page 30

    Description parameter choose automatic or manual provider network selection. For manual selection, please specify the provider. Network selec- tion: com port description parameter rs232 or rs485. Consider the pin assignments on chapter appendix a, connectors and cables physical pro- tocol: this prop...

  • Page 31

    Description parameter this property specifies the number of data bits contained in each frame. Data bits: in xon/xoff software flow control, either end can send a stop (xoff) or start (xon) character to the other end to control the rate of incoming data. Software flow control: in rts/cts hardware fl...

  • Page 32

    Description parameter digital inputs levels: 0 to 5.6 vdc logical level 0 7.2 to 40 vdc logical level 1 note negative input voltage is not recognised. Digital outputs parametres: 1 a maximal continuous current 60 vdc, 42 vac (vrms) maximal switching voltage 60 w maximal switching capacity • digital ...

  • Page 33

    ○ monitor the digital inputs and outputs every change of digital inputs triggers a message of the above format to be sent. It also contains the valid states of the outputs. ○ set digital outputs to set the states of the digital i/o send the following pattern as ascii characters description pattern t...

  • Page 34

    3.1.5. Routing static routing is the term used to refer to a manual method that is used to set up routing between net- works. Static routing has the advantage of being predictable and simple to set up. This section lists the routing table and lets the user add and delete routes. Description paramete...

  • Page 35

    Description parameter displays whether a particular route is persistent or not. Persistent displays whether a particular route is active or not. Active 3.1.6. Firewall access control lists • access control for local host – the access from the wan interface to m!Dge/mg102 itself and its local applica...

  • Page 36

    You can set both wan and open vpn rules. Description parameter enter the ip address of the device that is to expose. Leave this field blank to disable the feature. Exposed host: • access control for vpn tunnels and wan from lan – having the ethernet ports split into multiple lans this filter manages...

  • Page 37

    Napt this page lets you set the options for network address and port translation (napt). Napt is a feature that translates tcp or udp communications made between hosts on a private network and hosts on a public network. It allows a single public ip address to be used by many hosts on the private net...

  • Page 38

    • napt on openvpn interface the same settings as above, but for other interface expert mode upload text files with firewall rules. Gprs/edge/umts routersm!Dge, mg102 – © racom s.R.O. 38 configuration.

  • Page 39

    3.1.7. Vpn openvpn install an openvpn server or subscribe to the appropriate service. If you have your own openvpn server the first step in building an openvpn 2.0 configuration is to establish a pki (public key infrastructure). The pki consists of: ○ a separate certificate (also known as a public k...

  • Page 40

    • openvpn configuration (standard client configuration) description parameter set the active configuration configuration mode: use certificates or user name / password authentication meth- od: first openvpn server address first server address first openvpn server port, default 1194 first server port...

  • Page 41

    • openvpn client certificates description file type certificate file master certificate authority (ca) certificate and key which is used to sign each of the server and client certificates. *.Crt root certificate file separate certificate (also known as a public key) *.Crt client certificate file pri...

  • Page 42

    Openvpn configuration (server expert configuration) this configuration mode lets you run an openvpn server on m!Dge/mg102. The configuration upload takes a zip file which may include one or more openvpn server configurations. Typically such a zip file includes files such as: • server.Conf (the clien...

  • Page 43

    • ipsec administration description parameter enable or disable ipsec. Ipsec administrative status: • ipsec configuration 43 © racom s.R.O. – gprs/edge/umts routersm!Dge, mg102 configuration.

  • Page 44

    Gprs/edge/umts routersm!Dge, mg102 – © racom s.R.O. 44 configuration.

  • Page 45

    Description parameter ip address or host name of ipsec peer / responder / server. Remote server address: the remote private network. Provide an ip address in dotted decimal notation. Remote lan address: the remote private network. Provide a subnet mask in dotted decimal notation. Remote lan subnet m...

  • Page 46

    Pptp server the point-to-point tunneling protocol (pptp) is a method for implementing virtual private networks. Pptp is popular because it is easy to configure and it was the first vpn protocol that was supported by microsoft dial-up networking. Users that are allowed to connect to the pptp server a...

  • Page 47

    Dial-in server on this page the dial-in server of m!Dge/mg102 can be administrated and configured. Users that are allowed to dial-in are defined under the section “user accounts”. • dial-in server administration description parameter the dial-in server can be enabled or disabled. Consequently the de...

  • Page 48

    3.1.8. Services com server / gateway max packet size: limits the package size to the configured value • max packet timeout: if data is received on serial line, waits for more data for the configured time to avoid to much segmentation which would lead on inefficiency • max latency timeout: limits the...

  • Page 49

    • com server administration description parameter the com server / modbus gateway can be enabled or disabled. Com server status: • com server configuration description parameter “telnet” or “tcp raw” for com server applications, “modbus tcp” for modbus gateway protocol on tcp/ip: the protocol implic...

  • Page 50

    Description parameter udp port of remote remote port max. Lenght of packet max. Packet size if data is received on serial line, waits for more data for the configured time to avoid to much segmentation which would lead on inefficiency max. Packet timeout limits the maximum latency if the above crite...

  • Page 51

    Description parameter reference host 1 to which ip connectivity is checked by sending probes. Host 1: reference host 2 to which ip connectivity is checked by sending probes (optional). The test is considered successful if host 1 or 2 answers. Host 2: source ip address to be used as source of the pin...

  • Page 52

    Dhcp server the dhcp server assigns the following information: 1. Any ip address out of the configured range 2. As default gateway the ip address of m!Dge/mg102 is assigned 3. As dns server the ip address of m!Dge/mg102 is assigned or manually configured dns servers • dhcp server administration desc...

  • Page 53

    Description parameter address range size for dhcp server address range size: manually configured first dns server dns server 1: manually configured second dns server dns server 2: propagate dns proxy server as third dns server dns server 3: dns proxy server the dns proxy enabled m!Dge/mg102 forwards...

  • Page 54

    Dynamic dns the dynamic dns client of m!Dge/mg102 is completely compatible to the dynamic network services provided by the organization dyndns (www.Dyndns.Com). • dynamic dns administration description parameter enable or disable the dynamic dns client dynamic dns status: • dynamic dns configuration...

  • Page 55

    Description parameter username user name: password password: optional support e-mail address support e-mail: e-mail client • e-mail client administration description parameter sending e-mail can be enabled or disabled. Disabling the e-mail client means that no notification via e-mail will be perform...

  • Page 56

    Event manager • events there are several predefined system events. If such an event occurs a notification message to sms or e-mail recipients if such an events description parameter ppp connection up. Ppp0 interface address: %ppp_ip%. Ppp connection established ppp connection down. Ppp connection do...

  • Page 57

    Description parameter dial-in failure to connect. Dial-in connection failure dyndns update with %dyndns_ip% address. Dynamic dns registration dyndns failure to reach server. Dynamic dns failure to reach server log-in to the configuration gui, by the user: %login_user%. Login to the web manager faile...

  • Page 58

    Description parameter reason why a restart happened %restart_reas- on% status of digital input 1, possible values include [on, off] %dst_in1% status of digital input 2, possible values include [on, off] %dst_in2% status of digital output 1, possible values include [on, off] %dst_out1% status of digi...

  • Page 59

    • event processor notifications can be generated or digital outputs can be set based on the occurrence of several events. 59 © racom s.R.O. – gprs/edge/umts routersm!Dge, mg102 configuration.

  • Page 60

    Gps this feature is available on mg102xgx. If valid gps data is available (at least 3 satellites available) it will be sent as udp payload to the con- figured host. The content of such a data package is separated into two lines. The first line contains gps data in the gpgga format; the second line c...

  • Page 61

    Sms sms can be used to control m!Dge/mg102 and for event notification. Description parameter sending sms can be enabled or disabled. Disabling sending sms means that no notification via sms will be performed. Sms notification: receiving sms can be enabled or disabled. Disabling receiving sms means t...

  • Page 62

    Description parameters com- mand this will initiate a dial-out connection over gsm and the vpn connection (if enabled) and trigger sending an sms with the following information: • current ip address of the ppp interface • current ip address of the vpn interface (if enabled) the profile name is an op...

  • Page 63

    Ssh server description parameter ssh server port port: the standard port 22 is used. For higher security change it to different number. This number shall be used as parametr in ssh command. 63 © racom s.R.O. – gprs/edge/umts routersm!Dge, mg102 configuration.

  • Page 64

    Snmp agent description parameter enable or disable the snmp agent. Snmp agent status: snmp agent port. Listening port: an snmp community is the group that devices and management stations running snmp belong to. Community: system maintainer. Contact: location of the device. Location: the host where t...

  • Page 65

    • startup of the m!Dge/mg102 • shutdown of the m!Dge/mg102 • vpn connected • vpn disconnected • signal strength below „signal strength trap threshold“ the startup trap is implemented using the standard coldstart & warmstart traps. The system-shutdown trap is sent, when the system is rebooted via the...

  • Page 66

    Udp message receiver description parameter udp message receiver port port: the upd message receiver is a service that listens on the configured port (default 2157) for arriving udp packets with a string in the payload. If an upd package is arriving, the event “arriving udp message” is fired (see cha...

  • Page 67

    Unstructured supplementary services data (ussd) unstructured supplementary services data (ussd) is a gsm service that allows high speed interactive communication between the subscribers and applications across a gsm network. A sample ussd service is the bill status service accessed by dialing *141# ...

  • Page 68

    Web server description parameter web server port for http connections http port: web server port for https connections https port: gprs/edge/umts routersm!Dge, mg102 – © racom s.R.O. 68 configuration.

  • Page 69

    Captive portal the captive portal is used to redirect unauthorized wlan/lan clients to a login page where they have to authenticate against locally configured users or remotely over radius. Description parameter enable or disable the captive portal. Administrative status: define whether user must ac...

  • Page 70

    3.1.9. System authentication gprs/edge/umts routersm!Dge, mg102 – © racom s.R.O. 70 configuration.

  • Page 71

    User accounts this page lets you manage the user accounts on the device. The user admin is a built-in power user that has permission to access both the web manager and the dial-in server. Any other user-defined user only has permission for dial-in connections. Description parameter define a user nam...

  • Page 72

    • automatic file configurration description parameter enable/disable automatic configuration update status: every day at this time m!Dge/mg102 will do a check for updates time of day: update over mobile or ethernet interface? Mode: specify the protocol used to transfer the new user configuration fil...

  • Page 73

    • manual file configuration description parameter press [download] will download a zip file name user-config.Zip containing • user-config.Cfg • ca.Crt.Credential_mode • ca.Crt.Certificate_mode • client.Crt.Certificate_mode • client.Key.Certificate_mode • templateprofiles if available. Current config...

  • Page 74

    • factory reset press [reset] to set the device to factory default. Your current configuration will be lost. This action can also be initiated by pressing and holding the reset button for at least five seconds. The factory reset will also set the ip address of the ethernet interface to 192.168.1.1. ...

  • Page 75

    Troubleshooting • network debugging 75 © racom s.R.O. – gprs/edge/umts routersm!Dge, mg102 configuration.

  • Page 76

    • log files log files can be viewed a downloaded here. Please provide these files when placing a support re- quest. • system log redirection gprs/edge/umts routersm!Dge, mg102 – © racom s.R.O. 76 configuration.

  • Page 77

    Description parameter the host where the syslog messages will be forwarded to. A syslog server has to be running on this ip address. You can use free tftp server tftpd32 for example. Ip address: • restart • tech support 77 © racom s.R.O. – gprs/edge/umts routersm!Dge, mg102 configuration.

  • Page 78

    Note for using of this feature a connection to internet is required. • system information: provide this information when placing a support request. Gprs/edge/umts routersm!Dge, mg102 – © racom s.R.O. 78 configuration.

  • Page 79

    Time and region the network time protocol (ntp) is a protocol for synchronizing the clocks of computer systems over packet-switched, variable-latency data networks. M!Dge/mg102 can synchronize its system time with a ntp server. If enabled, time synchronisation is done after the mobile interface is u...

  • Page 80

    • automatic software update description parameter enable/disable automatic software update status: every day at this time m!Dge/mg102 will do a check for updates time of day: update over mobile or ethernet interface? Mode; specify the protocol used to transfer the new software to m!Dge/mg102. You wi...

  • Page 81

    Description parameter update over mobile or ethernet interface? Mode: specify the protocol used to transfer the new software to m!Dge/mg102. You will need an appropriate server. Protocol: provide a host name and a path to a server which hosts the new software. For local updates (tftp) this value is ...

  • Page 82

    Description para- meter download the recommended tftp server “tftpd32” from our website, install it on your pc and start it. Configure the tftp server as follows: -in the dialog „tftpd32: settings“ choose the base directory (e.G. „c:\tftp“). Create a new directory if there is none. - unpack the new ...

  • Page 83

    Licensing 3.1.10. Logout log out from web manager 3.2. Configuration parameters of the m!Dge/mg102 the information in this chapter is needed to configure m!Dge/mg102 via the command line interface or file configuration. If you are using the web manager and its forms to configure m!Dge/mg102, you may...

  • Page 84

    Racom has defined some types of parameters that are often used. The table below shows the defined parameter types. In addition other types of parameters may exist. Description format allowed charac- ters parameter type string must include “@” second part must be a valid hostname user@hostname a–z a–...

  • Page 85

    Description range default value parameter 0 = pin protection disabled 1 = pin protection enabled [0,1] 0 simcard.Sim2.Pinstatus [automatic,manual] automatic networkselection.Mode select the network provider defined by the supplied local area identity (lai) numeric value (lai) void networkselection.N...

  • Page 86

    Description range default value parameter acess point name hostname void dialout.Profiles.1.Apn 0 = off 1 = enable ip header compression [0,1] void dialout.Profiles.1.Iphc 0 = off 1 = enable software compression [0,1] void dialout.Profiles.1.Ipsc 0 = do not query dns server 1 = query dns server [0,1...

  • Page 87

    3.2.2. Routing related parameters description range d e f a u l t value parameter hostname void with l = [0..20] static_routes..Interface hostname void static_routes..Target netmask void static_routes..Mask hostname void static_routes..Gateway default is 0. [0..32766] void static_routes..Metric 3.2....

  • Page 88

    Napt on openvpn interface description range d e f a u l t value parameter 0 = napt off 1 = napt on [0,1] 1 with j = [0..49] napt_openvpn.Status external port range start [1 .. 65535] void napt_openvpn..Extport external por range end [1 .. 65535] void napt_openvpn..Intport ipaddress void napt_openvpn...

  • Page 89

    Access control list for exposed host on openvpn interface description range d e f a u l t value parameter 0 = deny all 1 = permit entries 0 = permit all [0,1,2] 1 firewall_exposed_host_openvpn.Policy the exposed host hostname void firewall_exposed_host_openvpn.Host source host / net hostname void wi...

  • Page 90

    Description range default value parameter openvpn server fqhn netmask 255.255.0.0 ipsec.Remote.Lanmask openvpn server port password void ipsec.Ike.Psk [identity-protec- tion, aggressive] identity-protec- tion ipsec.Ike.Mode 3des 3des ipsec.Ike.Encryption [sha1, md5] md5 ec.Ike.Hash [ m o d p 1 0 2 4...

  • Page 91

    3.2.5. Services related parameters com server description range default value parameter 0 = disabled 1= enabled [0,1] void serial_srv.Status [raw, telnet, modbus] telnet serial_srv.Opt.Protocol [1 .. 65535] 2000 serial_srv.Opt.Port [300, 1200, 2400, 4800, 9600, 19200, 38400, 115200] 115200 serial_sr...

  • Page 92

    Dynamic dns description range default value parameter dyndns = dynamic dns dyndns-static = static dns dyndns-custom = custom dns [dyndns, dyndns-static, dyndns-custom] dyndns dyndns.Servicetype hostname void dyndns.Hostname username void dyndns.Username password void dyndns.Password e-mail void dynd...

  • Page 93

    Gps parameters description range default value parameter 0 = dial-in disabled 1= dial-in enabled [0,1] 0 gps.Status hostname void gps.Destination.Hostname [1 .. 65535] void gps.Destination.Port [3..∞] 3 gps.Updatecycle event manager • events description range default value parameter event message pa...

  • Page 94

    Description range default value parameter event message password void events.Testevent.Message • subscribers description range d e f a u l t value parameter name of subscriber hostname void with k = [0..19] subscriber..Name phone number for sms phone number void subscriber..Sms.Destination e-mail ad...

  • Page 95

    Ssh server description range default value parameter [1 .. 65535] 22 sshserver.Port telnet server description range default value parameter [1 .. 65535] 23 telnetserver.Port web server description range default value parameter [1 .. 65535] 80 webserver.Http.Port [1 .. 65535] 80 webserver.Https.Port ...

  • Page 96

    Time synchronisation description range default value parameter 0 = disabled 1= enabled [0,1] 1 network.Ntp.Status ntp server hostname swisstime.Ethz.Ch ??? Network.Ntp.Server backup ntp server hostname void network.Ntp.Server2 time zone [ u t c - 1 2 … utc+12] utc+2 network.Timezone software update ...

  • Page 97

    Logon via telnet via windows telnet client logon via ssh with putty after authentication, type “cli help” into the shell to learn about the usage of the command line interface. Cli will stop after every call. You have to include ‘cli’ for every new call. 3.3.1. Cli overview the command line interfac...

  • Page 98

    Usage and return value command note cli set = returns no error message cli set = returns no error message, no range check is performed not for end user use! Root rights are required. Cli configure not for end user use! Root rights are required. Cli configureall ‘cli network’ provides mobile network ...

  • Page 99

    Usage and return value command ‘cli select manual’ selects the network provider defined by the supplied local area identity (lai) for the specified sim card usage: select manual [sim1/sim2] cli select manual note the following commands are identical: ‘cli select manual ’ and ‘cli select manual sim1 ...

  • Page 100

    Usage and return value command show the state of the napt service on the vpn if cli status overview networks napt_state_ovpn show the state of the openvpn connection cli status overview networks open- vpn_state show the state of the ipsec connection cli status overview networks ipsec_state show the ...

  • Page 101

    Usage and return value command not for end user use! Root rights are required. Exit 101 © racom s.R.O. – gprs/edge/umts routersm!Dge, mg102 configuration.

  • Page 102: 4. Software Interfaces

    4. Software interfaces 4.1. Gps server 4.1.1. Berlios gps server this is a tcp server which provides gps data in various formats. Find more information under ht- tp://gpsd.Berlios.De 4.1.2. Mg102 gps server if valid gps data is available it will be sent as udp payload to the configured host. The con...

  • Page 103

    Description data name no. Recommended minimum specific gps/transit data $gpgga sentence identifier 1 utc of position fix time 2 a = data ok v = navigation receiver warning data status 3 latitude of fix latitude 4 longitude of fix longitude 6 speed over ground in knots speed 8 track made good in degr...

  • Page 104: 5. Troubleshooting

    5. Troubleshooting 5.1. Error messages the web manager show error messages in the status bar in the footer of a certain web page. Common error messages are: problem solving error message insert a sim card sim missing insert the pin code on the “sim” page pin code required see the “debug log” under c...

  • Page 105

    105 © racom s.R.O. – gprs/edge/umts routersm!Dge, mg102 troubleshooting.

  • Page 106: 6. Customer Service

    6. Customer service 6.1. Support please send questions or comments about m!Dge/mg102 to: support@racom.Eu gprs/edge/umts routersm!Dge, mg102 – © racom s.R.O. 106 customer service.

  • Page 107

    Appendix a. Connectors and cables a.1. Pin assignments for the communication interfaces fig. A.1: serial connector sub-d 9pol plug female (dsub9f) tab. A.1: pin assignment com interface rs232 com – rs232 dsub9f in/ out signal pin o cd 1 o rxd 2 i txd 3 i dtr 4 gnd 5 o dsr 6 i rts 7 o cts 8 — ri 9 ta...

  • Page 108

    A.2. Ethernet plug (eth; rj-45) fig. A.2: rj-45 plug tab. A.3: pin assignment ethernet interface eth (ethernet 10ba- set and 100baset) rj-45 socket signal pin tx+ 1 tx− 2 rx+ 3 rx− 6 a.3. Power plug mg102 fig. A.3: power connector tab. A.4: pin assignment power plug power mstb 2,5/ 2-st-5,08 (phoeni...

  • Page 109

    Appendix b. Safety instructions the m!Dge/mg102 wireless router must be used in compliance with any and all applicable interna- tional and national laws and in compliance with any special restrictions regulating the utilization of the communication module in prescribed applications and environments....

  • Page 110

    B.2. Rohs and weee compliance the ray is fully compliant with the european commission‟s rohs (restriction of certain hazardous substances in electrical and electronic equipment) and weee (waste electrical and electronic equipment) environmental directives). Restriction of hazardous substances (rohs)...

  • Page 111: Appendix C. Glossary

    Appendix c. Glossary apn access point name / access point node ce consumer electronic label by consumer electronic association cea (www.Ce.Org 1 ) cs coding scheme csd circuit switched data dhcp dynamic host configuration protocol dmz demilitarized zone dns domain name system edge enhanced data serv...

  • Page 112

    Ppp point to point protocol ras remote access service (dial-in networking ppp) rohs restriction of hazardous substances sim subscriber identity module sw software tcp transmission control protocol tftp trivial file transfer protocol udp user datagram protocol umts universal mobile telecommunications...

  • Page 113

    Appendix d. Revision history 2011-11-01 revision 1.1 1. Xml version 113 © racom s.R.O. – gprs/edge/umts routersm!Dge, mg102 revision history.