- DL manuals
- RAD
- Modem
- 4-Wire Symmetrical VDSL Modem ASM-60
- Installation And Operation Manual
RAD 4-Wire Symmetrical VDSL Modem ASM-60 Installation And Operation Manual - page 49
ASM-60
Installation and Operation Manual
Appendix A IR-ETH Interface Module
Installation and Operation
A-3
A.3 Installation and Operation
Figure A-4
shows the Ethernet bridge layout, the location of the DIP switch, and
the rear panel components of the IR-ETH interface module with RJ-45 connector.
Figure A-4. IR-ETH Layout (UTP Option)
DIP Switch Settings
Table A-2
describes functions and default settings of the DIP switch SW-1 sections.
Table A-2. DIP Switch Settings
Section
Number
Name Description
Default
Setting
1
SQ/FD
ON – Full-duplex operation
OFF – Half-duplex operation
OFF
2
CMP
ON – Strips padding bits inserted in 64-byte frame
OFF – Transmits frames over WAN as is
OFF
3
FIL
ON – Passes only frames destined for another LAN
OFF – Disables LAN filter; passes all frames transparently
OFF
4
(nc)
Summary of 4-Wire Symmetrical VDSL Modem ASM-60
Page 1
Asm-60 installation and operation manual 4-wire symmetrical vdsl modem.
Page 3: Notice
Asm-60 4-wire symmetrical vdsl modem installation and operation manual notice this manual contains information that is proprietary to rad data communications ltd. ("rad"). No part of this publication may be reproduced in any form whatsoever without prior written approval by rad data communications. ...
Page 4: Limited Warranty
Limited warranty rad warrants to distributor that the hardware in the asm-60 to be delivered hereunder shall be free of defects in material and workmanship under normal use and service for a period of twelve (12) months following the date of shipment to distributor. If, during the warranty period, a...
Page 5: General Safety Instructions
General safety instructions the following instructions serve as a general guide for the safe installation and operation of telecommunications products. Additional instructions, if applicable, are included inside the manual. Safety symbols this symbol may appear on the equipment or in the text. It in...
Page 6: Handling Energized Products
Handling energized products general safety practices do not touch or tamper with the power supply when the power cord is connected. Line voltages may be present inside certain products even when the power switch (if installed) is in the off position or a fuse is blown. For dc-powered products, altho...
Page 7
Connection of data and telecommunications cables data and telecommunication interfaces are classified according to their safety status. The following table lists the status of several standard interfaces. If the status of a given port differs from the standard one, a notice will be given in the manu...
Page 8: Fcc-15 User Information
To reduce the risk of fire, use only no. 26 awg or larger telecommunication line cords. Pour réduire les risques s’incendie, utiliser seulement des conducteurs de télécommunications 26 awg ou de section supérieure. Some ports are suitable for connection to intra-building or non-exposed wiring or cab...
Page 9
Canadian emission requirements this class a digital apparatus meets all the requirements of the canadian interference-causing equipment regulation. Cet appareil numérique de la classe a respecte toutes les exigences du règlement sur le matériel brouilleur du canada. Warning per en 55022 (cispr-22) t...
Page 10
Asm-60 with ir-eth/qh interface module installation instructions for compliance with emc requirements to comply with electromagnetic compatibility requirements, use a shielded cable (stp) for connecting a 10/100baset lan to the rj-45 connector of the ir-eth/qh interface module..
Page 11: Declaration of Conformity
Declaration of conformity manufacturer's name: rad data communications ltd. Manufacturer's address: 24 raoul wallenberg st. Tel aviv 69719 israel declares that the product: product name: asm-60 conforms to the following standard(s) or other normative document(s): emc : en 55022: 1998 information tec...
Page 13: Quick Start Guide
Installing asm-60 1 quick start guide installation of asm-60 should be carried out only by an experienced technician. If you are familiar with asm-60, use this guide to prepare the units for operation. 1. Installing asm-60 setting the internal switches to set internal switches: 1. Disconnect the pow...
Page 14
Quick start guide asm-60 installation and operation manual 2 configuring asm-60 2. Operating asm-60 normal indications the table below shows the correct status of the indicators a few seconds after power-up. Indicator status pwr on td depends on dte data transmission rd depends on dte data transmiss...
Page 15: Contents
Asm-60 installation and operation manual i contents chapter 1. Introduction 1.1 overview..................................................................................................................... 1-1 versions.....................................................................................
Page 16
Table of contents ii asm-60 installation and operation manual chapter 5. Diagnostics 5.1 error detection............................................................................................................ 5-1 power-up self-test....................................................................
Page 17: List of Figures
Table of contents asm-60 installation and operation manual iii list of figures 1-1. Typical asm-60 application .................................................................................................. 1-1 1-2. 3d view of asm-60 ..................................................................
Page 18
Table of contents iv asm-60 installation and operation manual.
Page 19: Chapter 1
Overview 1-1 chapter 1 introduction 1.1 overview asm-60 is a vdsl (very high-bitrate digital subscriber line) modem handling high data rates. Asm-60 supports hssi dte interface, and several ethernet interface modules, which allow lan-to-lan connectivity using vdsl technology. Working in full duplex ...
Page 20
Chapter 1 introduction asm-60 installation and operation manual 1-2 overview features asm-60 utilizes the qam vdsl technology to extend the range of data transmission over 4-wire 24 awg line up to 2.0 km (1.2 miles). Asm-60 operates at the following data rates: 4.096 mbps, 6.144 mbps and 10.24 mbps....
Page 21
Asm-60 installation and operation manual chapter 1 introduction physical description 1-3 1.2 physical description figure 1-2 shows a 3d view of the asm-60 standalone modem. Figure 1-2. 3d view of asm-60 the front panel includes nine leds, which display the status of power, data flow, control signals...
Page 22
Chapter 1 introduction asm-60 installation and operation manual 1-4 functional description 1.3 functional description this section provides a functional description ( figure 1-3 ) of asm-60 in the form of block diagrams. Cpu additional decoder latch/buffer d8-d15 vdsl framer dte interface txd, rxd i...
Page 23
Asm-60 installation and operation manual chapter 1 introduction technical specifications 1-5 1.4 technical specifications line interface protocol very high-bit-rate digital subscriber line (vdsl) type 4-wire, unconditioned dedicated lines (twisted pair), cat.3 and cat.5, 19 awg to 26 awg line coding...
Page 24
Chapter 1 introduction asm-60 installation and operation manual 1-6 technical specifications indicators pwr (green) power rts (yellow) request to send td (yellow) transmit data rd (yellow) receive data dcd (yellow) data carrier detect tst (red) test alm (red) alarm sync a (green/red) synchronization...
Page 25: Chapter 2
Site requirements and prerequisites 2-1 chapter 2 installation and setup this chapter describes installation and setup procedures for the standalone asm-60 modem. Asm-60 is delivered completely assembled. It is designed for tabletop or 19-inch rack installation. After installing the unit: • refer to...
Page 26
Chapter 2 installation and setup asm-60 installation and operation manual 2-2 installation and setup 2.2 package contents the asm-60 package includes the following items: • one asm-60 unit • last mile access and intelligent modems cd • ac power cord • rm-28 rack installation kit (if ordered). 2.3 in...
Page 27
Asm-60 installation and operation manual chapter 2 installation and setup installation and setup 2-3 opening the asm-60 case to open the asm-60 case: 1. Disconnect the power cord from the power source. 2. Slide the blue side panel forward to detach it from the case. 3. Unscrew the two screws located...
Page 28
Chapter 2 installation and setup asm-60 installation and operation manual 2-4 installation and setup connecting the dte the asm-60 dte interface provides interface for input/output data, clock reference and control signals between the modem and the dte. The asm-60 dte interface can be either hssi in...
Page 29
Asm-60 installation and operation manual chapter 2 installation and setup installation and setup 2-5 connecting the power before switching on this unit and connecting any other cable, the protective earth terminals of this unit must be connected to the protective ground conductor of the power cord. ...
Page 30
Chapter 2 installation and setup asm-60 installation and operation manual 2-6 installation and setup.
Page 31: Chapter 3
Front panel indicators 3-1 chapter 3 operation this chapter provides the description of the asm-60 front-panel indicators, and details the modem's operating procedures (turn-on, front-panel indications, performance monitoring and turn-off). Installation procedures given in chapter 2 must be complete...
Page 32
Chapter 3 operation asm-60 installation and operation manual 3-2 operating asm-60 table 3-1. Led indicators (cont.) name function sync a (red/green) on (red) – data link a is not synchronized with the remote modem on (green) – data link a is synchronized with the remote modem sync b (red/green) on (...
Page 33: Chapter 4
Preparing for the control session 4-1 chapter 4 management from a terminal the configuration of asm-60 is performed via menu-driven embedded software using a standard ascii terminal or a pc running a terminal emulation application connected to the front panel control dce port. This terminal can be u...
Page 34
Chapter 4 management from a terminal asm-60 installation and operation manual 4-2 navigating the management menus table 4-1. Control port control signals control line interface type dce dte cts out not used dcd out out dsr out out dtr in in ri not used in rts in in data terminal ready (dtr) when con...
Page 35
Asm-60 installation and operation manual chapter 4 management from a terminal starting the control session 4-3 terminal management menus figure 4-1 show s a map of the management menus in the asm-60 embedded software. The second level menus (configuration, display, reset) are described in its own se...
Page 36
Chapter 4 management from a terminal asm-60 installation and operation manual 4-4 configuring asm-60 asm-60/co main menu 1. Configuration 2. Display 3. Test 4. Reset 5. Debug > esc - previous menu ; ! - main menu ; & - exit terminal ------------------------------------------------------- figure 4-2....
Page 37
Asm-60 installation and operation manual chapter 4 management from a terminal displaying the asm-60 system information 4-5 data rate (current value) enter the devise bit rate 1. 4096 kbps 2. 6144 kbps 3. 10240 kbps > esc - previous menu ; ! - main menu ; & - exit terminal ---------------------------...
Page 38
Chapter 4 management from a terminal asm-60 installation and operation manual 4-6 displaying the asm-60 system information displaying the asm-60 status you can display the current status of the local and remote asm-60 modems. To display the asm-60 status: • from the display menu, type 1 . The status...
Page 39
Asm-60 installation and operation manual chapter 4 management from a terminal resetting asm-60 4-7 4.6 resetting asm-60 you can perform reset of the main components of asm-60, or reset the modem to its factory settings. To reset asm-60: 1. From the main menu, type 4 . The reset menu appears ( figure...
Page 40
Chapter 4 management from a terminal asm-60 installation and operation manual 4-8 resetting asm-60
Page 41: Chapter 5
Error detection 5-1 chapter 5 diagnostics this chapter describes the asm-60 diagnostic functions, which include: • status indications, alarms, power-up self-test • vdsl performance diagnostics • led testing. 5.1 error detection this section explains how to detect and fix errors and other problematic...
Page 42
Chapter 5 diagnostics asm-60 installation and operation manual 5-2 error detection alarms dcd failed > esc - previous menu ; ! - main menu ; & - exit terminal ------------------------------------------------------- figure 5-1. Alarms screen the display of the alarms screen includes only the name of ...
Page 43
Asm-60 installation and operation manual chapter 5 diagnostics displaying the vdsl performance diagnostics 5-3 table 5-1. Asm-60 alarms number terminal message description severity 1 fpga download failed failure to download programming to the asm-60 fpga microprocessor major 2 self test error a prob...
Page 44
Chapter 5 diagnostics asm-60 installation and operation manual 5-4 displaying the vdsl performance diagnostics vdsl performance line a lock status: sync line a avg. Snr.: 34 line a ber pre fec: 0.000e+00 line a ber after fec: 0.000e+00 line b lock status: sync line b avg. Snr.: 34 line b ber pre fec...
Page 45
Asm-60 installation and operation manual chapter 5 diagnostics running the diagnostic tests 5-5 5.3 running the diagnostic tests running the leds test the asm-60 modem can perform the front-panel indicators test to verify that the unit leds are functioning properly. To run the leds test: 1. From the...
Page 46
Chapter 5 diagnostics asm-60 installation and operation manual 5-6 running the diagnostic tests.
Page 47: Appendix A
Ir-eth connector options a-1 appendix a ir-eth interface module ir-eth is an interface module for rad modems, used for converting the ethernet (10baset or 10base2) electrical levels to the modem ttl levels. It also converts the ethernet protocol to hdlc to enable long-distance transmission and avoid...
Page 48
Appendix a ir-eth interface module asm-60 installation and operation manual a-2 technical specifications a-1 2 4 5-b : for continued type and rating of fuse. Fire, replace only with same protection against risk of caution 100 -23 0 v a c 0. 25 0a t 2 50v 10base-2 tx coll rx line figure a-3. Rear pan...
Page 49
Asm-60 installation and operation manual appendix a ir-eth interface module installation and operation a-3 a.3 installation and operation figure a-4 shows the ethernet bridge layout, the location of the dip switch, and the rear panel components of the ir-eth interface module with rj-45 connector. Fi...
Page 50
Appendix a ir-eth interface module asm-60 installation and operation manual a-4 installation and operation led indicators table a-3 lists the ir-eth led indicators and describes their functions. Table a-3. Ir-eth bridge led indicators led name description location color link on – good link integrity...
Page 51: Appendix B
Ir-eth/qh connector b-1 appendix b ir-eth/qh interface module b.1 introduction the ir-eth/qh interface module includes a high performance self-learning fast ethernet bridge, which is connected to the lan via a single 10baset or 100baset port, operating in full duplex and providing offer simple and c...
Page 52
Appendix b ir-eth/qh interface module asm-60 installation and operation manual b-2 installation and operation table b-1. Rj-45 connector pinout pin signal function 1 rd (+) receive data (positive) 2 rd (-) receive data (negative) 3 td (+) transmit data (positive) 6 td (-) transmit data (negative) b....
Page 53
Asm-60 installation and operation manual appendix b ir-eth/qh interface module installation and operation b-3 setting the dip switch configure the ir-eth/qh module by setting the dip switch in accordance with table b-2 . The dip switch is located on the reverse side of the ir-eth/qh module. To chang...
Page 54
Appendix b ir-eth/qh interface module asm-60 installation and operation manual b-4 installation and operation connecting the lan use either a straight cable or a cross cable for the lan connection. Use a cross cable when connecting to a port that does not implement the crossover function internally....
Page 55: Appendix C
Introduction c-1 appendix c ir-ip interface module c.1 introduction overview ir-ip is a high-performance, miniature ip router based on rad's unique ip router chip, the chiprouter. Ir-ip works by taking each ethernet frame from the lan and determining whether the ip packet is destined for the ip net ...
Page 56
Appendix c ir-ip interface module asm-60 installation and operation manual c-2 physical description application figure c-1 shows a typical application of the asm-60 modem equipped with the ir-ip interface module. Asm-60 with v.35 interface router asm-60 with ir-ip figure c-1. Typical application of ...
Page 57
Asm-60 installation and operation manual appendix c ir-ip interface module physical description c-3 ir-ip leds ir-ip contains three leds, which indicate the module activity. Table c-1 lists the leds functions. Table c-1. Ir-ip leds functions name type function int green led on – lan integrity is est...
Page 58
Appendix c ir-ip interface module asm-60 installation and operation manual c-4 ir-ip management subsystem, general c.4 ir-ip management subsystem, general introduction the ir-ip interface module management subsystem supports the following functions: • preliminary configuration • configuration of man...
Page 59
Asm-60 installation and operation manual appendix c ir-ip interface module performing preliminary configuration c-5 default ip communication parameters the default ip communication parameters of the interface module are: • the default ip address of the ir-ip ethernet port is 192.168.205.1, and the d...
Page 60
Appendix c ir-ip interface module asm-60 installation and operation manual c-6 performing preliminary configuration connecting the telnet host before starting the management and configuration activities, it is necessary to establish ip communication between your telnet host and the ir-ip interface m...
Page 61
Asm-60 installation and operation manual appendix c ir-ip interface module performing preliminary configuration c-7 the ip address is actually retrieved from the arp frames sent during pinging to locate the ping destination, not from the ping frames. To ensure that the process is correctly performed...
Page 62
Appendix c ir-ip interface module asm-60 installation and operation manual c-8 performing preliminary configuration after changing the destination ip address of the telnet host, it is recommended to turn asm-60 off for a few seconds and then back on, before continuing the configuration of the ip rou...
Page 63
Asm-60 installation and operation manual appendix c ir-ip interface module ir-ip management utility c-9 c.6 ir-ip management utility general operating procedures the ir-ip interface module is managed via a simple, menu-driven utility that uses a basic terminal user interface. A typical screen is sho...
Page 64
Appendix c ir-ip interface module asm-60 installation and operation manual c-10 quick setup menu menu structure of management utility figure c-5 shows the menu structure of the ir-ip management utility. Main menu 1. Quick setup 1. Lan ip address 2. Lan ip mask 3. Wan ip address 4. Wan ip mask 5. Def...
Page 65
Asm-60 installation and operation manual appendix c ir-ip interface module quick setup menu c-11 lan ip address used to enter the ip address for the ip router lan interface. This is the address to which nodes connected to the local lan send packets addressed to the wan. Lan ip mask used to enter the...
Page 66
Appendix c ir-ip interface module asm-60 installation and operation manual c-12 quick setup menu operation with default gateway you can instruct ir-ip to send packets with destinations not located on the local lan to a specific router, which is called the default gateway . The default gateway must b...
Page 67
Asm-60 installation and operation manual appendix c ir-ip interface module management access menu c-13 c.8 management access menu the management access menu is used to enable the use of passwords to protect the access to ir-ip management utility, and control the inactivity time-out interval. When pa...
Page 68
Appendix c ir-ip interface module asm-60 installation and operation manual c-14 advanced setup menu c.9 advanced setup menu the advanced setup menu is used to select the desired group of ir-ip configuration parameters. The parameters accessed through advanced setup menu supplement the parameters ava...
Page 69
Asm-60 installation and operation manual appendix c ir-ip interface module advanced setup menu c-15 device name select this parameter to assign an arbitrary name to ir-ip for identification by the system manager (up to eight characters). The assigned name is displayed in the screen header. Contact p...
Page 70
Appendix c ir-ip interface module asm-60 installation and operation manual c-16 advanced setup menu wan throttle this parameter specifies the maximum data rate at which frames are sent to the wan (i.E., to the asm-60 line). The available selections are: • 64 kbps • 128 kbps • 256 kbps • 512 kbps • 1...
Page 71
Asm-60 installation and operation manual appendix c ir-ip interface module advanced setup menu c-17 eir used to specify the maximum amount of data, in bits, that the frame relay network will attempt to deliver during the measurement interval. The value of this parameter is obtained from the frame re...
Page 72
Appendix c ir-ip interface module asm-60 installation and operation manual c-18 advanced setup menu security host/guest this option can be used to configure the ip router either as a guest unit, to be authenticated by another router, or as a host unit, that authenticates other routers. User name to ...
Page 73
Asm-60 installation and operation manual appendix c ir-ip interface module advanced setup menu c-19 multicast ip menu the multicast ip menu is used to specify the ip multicast frame forwarding parameters, and to access the static multicast groups’ table. To access the multicast ip menu: • from the a...
Page 74
Appendix c ir-ip interface module asm-60 installation and operation manual c-20 device control menu static groups select this parameter to access the static multicast groups table. The table is used to specify the ip addresses for up to 10 ip multicast groups. You can add, change, or delete each ent...
Page 75
Asm-60 installation and operation manual appendix c ir-ip interface module device control menu c-21 new software download menu ir-ip operates as a tftp client, and therefore it is possible to update its software by downloading new software from another computer that operates as a tftp server. The ne...
Page 76
Appendix c ir-ip interface module asm-60 installation and operation manual c-22 device control menu view error log screen this item of the device control submenu is used to view the error log file. This file logs errors detected in ir-ip for debug and technical support purposes. Resets menu the rese...
Page 77
Asm-60 installation and operation manual appendix c ir-ip interface module view menu c-23 reset wan to reset the wan interface: • from the resets menu, type 3 . You will be prompted to confirm the reset operation. Resetting the wan interface causes the wan controller to be restarted. This results in...
Page 78
Appendix c ir-ip interface module asm-60 installation and operation manual c-24 view menu ir_ip s/w ver. 1.00 31/ir (date) view configuration ------------------ boot version :1.06 18.03.1999 device name :ip router card system location :the location of this device contact person :name of contact pers...
Page 79
Asm-60 installation and operation manual appendix c ir-ip interface module view menu c-25 ir_ip s/w ver. 1.00 31/ir (date) multicast groups table ---------------------- group ip address status group ip address status press any key for exit figure c-22. Multicast groups table screen statistics screen...
Page 80
Appendix c ir-ip interface module asm-60 installation and operation manual c-26 diagnostic tool (ping terminal) menu ir_ip s/w ver. 1.00 31/ir (date) system statistics ----------------- counter name val counter name val wan in octets 83504 wan alignment errors 0 wan out octets 1950 wan aborted frame...
Page 81
Asm-60 installation and operation manual appendix c ir-ip interface module diagnostic tool (ping terminal) menu c-27 using the ping function the ping option is used to confirm ip connectivity by pinging other ip hosts. Connectivity is confirmed by receiving a reply from the remote (pinged) ip host. ...
Page 82
Appendix c ir-ip interface module asm-60 installation and operation manual c-28 erasing ir-ip software c.13 erasing user’s configuration the user-defined configuration parameters are stored in the ip router card flash memory. After the user-defined configuration parameters are erased, the ip router ...
Page 83
Asm-60 installation and operation manual appendix c ir-ip interface module erasing ir-ip software c-29 erasing application software to erase the application software: 1. Turn asm-60 off. 2. Set all the four sections of ir-ip dip switch to on. 3. Turn asm-60 on and monitor the ip router err indicator...
Page 84
Appendix c ir-ip interface module asm-60 installation and operation manual c-30 erasing ir-ip software.
Page 85: Customer Response Form
24 raoul wallenberg st., tel aviv 69719, israel tel: +972-3-6458181, fax: +972-3-6483331, +972-3-6498250 e-mail: , web site: customer response form rad data communications would like your help in improving its product documentation. Please complete and return this form by mail or by fax or send us a...
Page 87: Error Report
Error report type of error(s) ❒ incompatibility with product or problem(s): ❒ difficulty in understanding text ❒ regulatory information (safety, compliance, warnings, etc.) ❒ difficulty in finding needed information ❒ missing information ❒ illogical flow of information ❒ style (spelling, grammar, re...
Page 90
900 corporate drive, mahwah, n.J. 07430, tel: (201) 529-1100 24 raoul wallenberg street, tel aviv 69719, israel, tel: 972-3-6458181 u.S. Headquarters: international headquarters: publication no. 145-200-11/02 www.Rad.Com fax: 972-3-6498250, 972-3-6474436, email: rad@rad.Co.Il toll free: 1-800-444-72...