- DL manuals
- RAD
- Modem
- ASM-40
- Installation And Operation Manual
RAD ASM-40 Installation And Operation Manual
Summary of ASM-40
Page 1
Asm-40 high-speed short-range modem version 1.0 instal lation and operati on manual innovative access solutions.
Page 3: Asm-40
Asm-40 high-speed short-range modem version 1.0 installation and operation manual notice this manual contains information that is proprietary to rad data communications ltd. ("rad"). No part of this publication may be reproduced in any form whatsoever without prior written approval by rad data commu...
Page 4: Limited Warranty
Limited warranty rad warrants to distributor that the hardware in the asm-40 to be delivered hereunder shall be free of defects in material and workmanship under normal use and service for a period of twelve (12) months following the date of shipment to distributor. If, during the warranty period, a...
Page 5: General Safety Instructions
General safety instructions the following instructions serve as a general guide for the safe installation and operation of telecommunications products. Additional instructions, if applicable, are included inside the manual. Safety symbols this symbol may appear on the equipment or in the text. It in...
Page 6: Handling Energized Products
Handling energized products general safety practices do not touch or tamper with the power supply when the power cord is connected. Line voltages may be present inside certain products even when the power switch (if installed) is in the off position or a fuse is blown. For dc-powered products, altho...
Page 7
Before connecting the dc supply wires, ensure that power is removed from the dc circuit. Locate the circuit breaker of the panel board that services the equipment and switch it to the off position. When connecting the dc supply wires, first connect the ground wire to the corresponding terminal, then...
Page 8
There are restrictions on the diameter of wires in the telecom cables, between the equipment and the mating connectors. To reduce the risk of fire, use only no. 26 awg or larger telecommunication line cords. Pour réduire les risques s’incendie, utiliser seulement des conducteurs de télécommunication...
Page 9: Fcc-15 User Information
Fcc-15 user information this equipment has been tested and found to comply with the limits of the class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial envir...
Page 10: Declaration of Conformity
Declaration of conformity manufacturer's name: rad data communications ltd. Manufacturer's address: 24 raoul wallenberg st., tel aviv 69719, israel declares that the product: product name: asm-40 conforms to the following standard(s) or other normative document(s): emc: en 55022: 1998 information te...
Page 11: Quick Start Guide
Asm-40 ver. 1.0 installing asm-40 1 quick start guide installation of asm-40 should be carried out only by an experienced technician. If you are familiar with asm-40, use this quick start guide to set it up for operation. This guide describes the standalone version of the modem. Perform the installa...
Page 12
Quick start guide installation and operation manual 2 installing asm-40 asm-40 ver. 1.0 dip switch function possible settings factory setting the front panel pushbuttons off – the diagnostic tests cannot be activated via the front panel v54e section, sw3/2 controls activation of the local digital lo...
Page 13
Installation and operation manual quick start guide asm-40 ver. 1.0 operating asm-40 3 dip switch function possible settings factory setting j4, chass controls the connection between the asm-40 signal ground and the frame (chassis) ground con – signal ground is connected to the frame ground dis – si...
Page 14
Quick start guide installation and operation manual 4 operating asm-40 asm-40 ver. 1.0 • dcd: on • test: off..
Page 15: Contents
Asm-40 ver. 1.0 i contents chapter 1. Introduction 1.1 overview.................................................................................................................... 1-1 versions ..............................................................................................................
Page 16
Table of contents installation and operation manual ii asm-40 ver. 1.0 chapter 5. Asm-40/r card 5.1 asm-mn-214 card cage ............................................................................................. 5-1 line connector .....................................................................
Page 17: Chapter 1
Asm-40 ver. 1.0 overview 1-1 chapter 1 introduction 1.1 overview asm-40 is a high speed, synchronous short-range modem operating at full-duplex over unconditioned lines. Asm-40 also functions as a baud rate and interface converter. Product options the following versions of the modem are available: •...
Page 18
Chapter 1 introduction installation and operation manual 1-2 overview asm-40 ver. 1.0 features asm-40 operates at 13 selectable rates of up to 2048 kbps, for a line attenuation of up to 40 db on twisted pair or coax cable. This provides an approximate operating range of up to 1.75 km (1 mile). Asm-4...
Page 19
Installation and operation manual chapter 1 introduction asm-40 ver. 1.0 functional description 1-3 1.2 physical description asm-40 is available as a standalone unit or as a rack-mount card for the asm-mn-214 hub. Figure 1-3 shows the 3d view of the asm-40 standalone unit. Figure 1-3. Asm-40 standal...
Page 20
Chapter 1 introduction installation and operation manual 1-4 functional description asm-40 ver. 1.0 timing generator this circuit is a pll circuit. Asm-40 transmits data to the line at the following baud rates: 2048, 1544, 1536, or 1920 kbps. The baud rates support different data rates, which enable...
Page 21
Installation and operation manual chapter 1 introduction asm-40 ver. 1.0 functional description 1-5 tx int txd rxd rxd txd ext rcv tx fifo tx tx tx txd rxd tc & rc ext clk rx rx rx rx rc rx fifo fifo fifo asm-40 asm-40 asm-40 clock recovery rc tc & rc clock recovery clock recovery td rd pll tc & rc ...
Page 22
Chapter 1 introduction installation and operation manual 1-6 functional description asm-40 ver. 1.0 xmt fifo rcv fifo xmt g.703-hdb3 rcv g.703-hdb3 g.703-hdb3 interface basic asm-40 data and clk (input) data and clk (output) tx rx internal external data data receive data data ext or hdb internal, re...
Page 23
Installation and operation manual chapter 1 introduction asm-40 ver. 1.0 technical specifications 1-7 receiver an agc end equalizer provides the received signal for the clock and data recovery circuitry. Nrz interface the digital side provides an interface choice of v.35, x.21, rs-232, rs-530, v.36 ...
Page 24
Chapter 1 introduction installation and operation manual 1-8 technical specifications asm-40 ver. 1.0 connector db-15 or 5-clip terminal block: • 100Ω for 1544 kbps and 1536 kbps balanced • 120Ω for 2048 kbps and 1920 kbps balanced bnc coax: • 75Ω for 2048 and 1920 kbps unbalanced dte interface data...
Page 25
Installation and operation manual chapter 1 introduction asm-40 ver. 1.0 technical specifications 1-9 diagnostics v.54 loopbacks local loopback (llb): activated by a front panel pushbutton or by the dte interface signal (v.24, v.35 and rs-530 only) remote loopback (rem): activated by a front panel p...
Page 26
Chapter 1 introduction installation and operation manual 1-10 technical specifications asm-40 ver. 1.0
Page 27: Chapter 2
Asm-40 ver. 1.0 site requirements and prerequisites 2-1 chapter 2 installation and setup this chapter describes installation and setup procedures for the standalone asm-40 modem. Asm-40 is delivered completely assembled. It is designed for tabletop or 19-inch rack installation. For rack installation...
Page 28
Chapter 2 installation and setup installation and operation manual 2-2 installation and setup asm-40 ver. 1.0 2.2 package contents the asm-40 package includes the following items: • one asm-40 unit • last mile access and intelligent modems cd • cbl-530/449 adapter cable for the asm-40 units with v.3...
Page 29
Installation and operation manual chapter 2 installation and setup asm-40 ver. 1.0 installation and setup 2-3 3. Select the line code (sw4). The line code must be the same for both local and remote units. Hdb3 – select the 32, 64, 128, 256, 512, 1024, 1920 and 2048 kbps data rate. In this case the b...
Page 30
Chapter 2 installation and setup installation and operation manual 2-4 installation and setup asm-40 ver. 1.0 table 2-1. Asm-40 internal jumpers and switches dip switch function possible settings factory setting ex/r and int sections, sw4/1, 2 select the transmit clock int – on, internal clock. Ex/r...
Page 31
Installation and operation manual chapter 2 installation and setup asm-40 ver. 1.0 installation and setup 2-5 table 2-1. Asm-40 internal jumpers and switches (cont.) dip switch function possible settings factory setting rlbe section, sw3/6 enables remote digital loopback activation from the dte (via...
Page 32
Chapter 2 installation and setup installation and operation manual 2-6 installation and setup asm-40 ver. 1.0 connecting the line the asm-40 line connector may be optionally db-15 female or a 5-port terminal block or two bnc coax connections. Refer to the appropriate section below for the descriptio...
Page 33
Installation and operation manual chapter 2 installation and setup asm-40 ver. 1.0 installation and setup 2-7 connector pin allocations for the ir-eth, ir-ip, and ir-eth/qn interface modules appear in appendix b , appendix c , appendix d and appendix e respectively; pin assignments for the rest of t...
Page 34
Chapter 2 installation and setup installation and operation manual 2-8 installation and setup asm-40 ver. 1.0
Page 35: Chapter 3
Asm-40 ver. 1.0 front panel controls and indicators 3-1 chapter 3 operation this chapter provides the following information for the asm-40 standalone modem: • asm-40 front-panel indicators and controls • operating procedures (turn-on, front-panel indications, performance monitoring and turn-off). In...
Page 36
Chapter 3 operation installation and operation manual 3-2 operating procedure asm-40 ver. 1.0 table 3-1. Asm-40 front panel controls and indicators (cont.) name type function dig pushbutton the digital loopback pushbutton causes the local asm-40 to loop received data to its transmitter. Data set rea...
Page 37
Installation and operation manual chapter 3 operation asm-40 ver. 1.0 operating procedure 3-3 normal indications if the local and remote asm-40 units are in operation and transmitting/receiving data, the following indicator conditions exist: • pwr: on • rts: on • td: flashing when transmitting • rd:...
Page 38
Chapter 3 operation installation and operation manual 3-4 operating procedure asm-40 ver. 1.0
Page 39: Chapter 4
Asm-40 ver. 1.0 v.54 loopback tests 4-1 chapter 4 troubleshooting and diagnostics this chapter contains procedures for performing system diagnostic tests for asm-40. Use the test procedures provided in this chapter to: • verify normal system operation • isolate faulty equipment • identify other sour...
Page 40
Chapter 4 troubleshooting and diagnostics installation and operation manual 4-2 v.54 loopback tests asm-40 ver. 1.0 local analog loopback (llb) the local analog loopback (llb) test checks the performance of the local asm-40 modem, the local data terminal, and the connections between them (see figure...
Page 41
Installation and operation manual chapter 4 troubleshooting and diagnostics asm-40 ver. 1.0 v.54 loopback tests 4-3 local dte remote dte link interface link interface transmit rem pressed receive receive local asm-40 remote asm-40 transmit data data clock clock figure 4-2. Remote digital loopback to...
Page 42
Chapter 4 troubleshooting and diagnostics installation and operation manual 4-4 internal bert asm-40 ver. 1.0 local dte remote dte link interface link interface transmit dig pressed receive receive transmit data data clock clock local asm-40 remote asm-40 figure 4-3. Local digital loopback to activa...
Page 43
Installation and operation manual chapter 4 troubleshooting and diagnostics asm-40 ver. 1.0 internal bert 4-5 2. Press the patt pushbutton. Verify that: test led is lit err led lights up momentarily. If errors are encountered, the err led lights (for continuous errors) or blinks (for intermittent er...
Page 44
Chapter 4 troubleshooting and diagnostics installation and operation manual 4-6 internal bert asm-40 ver. 1.0 pattern generator pattern generator patt pressed (disconnects external bert) patt pressed (disconnects external bert) line interface line interface asm-40 asm-40 pattern tester pattern teste...
Page 45: Chapter 5
Asm-40 ver. 1.0 asm-mn-214 card cage 5-1 chapter 5 asm-40/r card this chapter describes the asm-40/r card version, designed for installation in the asm-mn-214 card cage. The chapter contains the following sections: • the asm-mn-214 card cage • the asm-40/r card version • power supply to asm-40/r car...
Page 46
Chapter 5 asm-40/r card installation and operation manual 5-2 power supply asm-40 ver. 1.0 asm-40/r with one of the ethernet interfaces (ir-eth or ir-eth/qn) uses a cia/eth interface adapter, which converts one db-25 connector to an rj-45 connector. The adapter cable and interface attachments are al...
Page 47
Installation and operation manual chapter 5 asm-40/r card asm-40 ver. 1.0 asm-40/r front panel 5-3 dc supply the dc power supply is -48 vdc (-36 to -72 vdc) or 24 vdc (18 to 32 vdc). It uses a dc/dc converter module to provide the power required for the cards. Power supply with redundancy this speci...
Page 48
Chapter 5 asm-40/r card installation and operation manual 5-4 asm-40/r front panel asm-40 ver. 1.0 td rd dcd test err dig ana rem patt asm-40 pwr rts figure 5-2. Asm-40/r front panel.
Page 49
Installation and operation manual chapter 5 asm-40/r card asm-40 ver. 1.0 installing the asm-40/r card 5-5 figure 5-3. Asm-mn-214 front panel 5.4 installing the asm-40/r card setting internal jumpers and switches the asm-40/r internal dip switches are similar in their functionality to those of the s...
Page 50
Chapter 5 asm-40/r card installation and operation manual 5-6 installing the asm-40/r card asm-40 ver. 1.0 fu s e 2 5 0 v 1a fu s e 2 5 0 v 1a f1 f2 chas s j5 dis con figure 5-4 asm-40/r pcb layout, component side installing asm-40/r into the asm-mn-214 card cage to install the asm-40/r card in the ...
Page 51
Installation and operation manual chapter 5 asm-40/r card asm-40 ver. 1.0 installing the asm-40/r card 5-7 connecting the interfaces asm-40/r uses the asm-mn-214 rear panel terminal block ports for the line connections. The 25-pin d-type female connector serves as a dte port. 1. Remove the protectio...
Page 52
Chapter 5 asm-40/r card installation and operation manual 5-8 installing the asm-40/r card asm-40 ver. 1.0
Page 53: Appendix A
Asm-40 ver. 1.0 v.24, v.35, x.21 and rs-530 dte interface connectors a-1 appendix a pinouts a.1 v.24, v.35, x.21 and rs-530 dte interface connectors table a-1 lists the pin assignments of the v.24/rs-232, v.35, x.21 and rs-530 interface connectors. Table a-1. Dte interface signal assignments rs-232 ...
Page 54
Appendix a pinouts installation and operation manual a-2 v.24, v.35, x.21 and rs-530 dte interface connectors asm-40 ver. 1.0 rs-232 v.35 rs-530 x.21 description signal function db-25 standalone and card cage db-25 card cage 34-pin standalone pin circuit db-25 standalone and card cage pin circuit db...
Page 55
Installation and operation manual appendix a pinouts asm-40 ver. 1.0 v.24, v.35, x.21 and rs-530 dte interface connectors a-3 rs-232 v.35 rs-530 x.21 description signal function db-25 standalone and card cage db-25 card cage 34-pin standalone pin circuit db-25 standalone and card cage pin circuit db...
Page 56
Appendix a pinouts installation and operation manual a-4 v.36 interface connector asm-40 ver. 1.0 a.2 v.36 interface connector the asm-40 v.36 interface is provided via an adapter cable converting between 25-pin rs-530 connector and 37-pin v.36 connector. Table a-2 lists the cable wiring. Table a-2....
Page 57
Installation and operation manual appendix a pinouts asm-40 ver. 1.0 asm-40/r with g.703-hdb3 interface a-5 a.3 asm-40/r with ethernet interface, dte connection asm-40/r with the ir-eth or ir-eth/qn ethernet interface module uses a cia/eth interface adapter, which converts one db-25 connector to an ...
Page 58
Appendix a pinouts installation and operation manual a-6 asm-40/r with g.703 codirectional interface asm-40 ver. 1.0 chassis ground rcv1* (input) rcv2 (input) xmt1 (output) xmt2* (output) figure a-2. Terminal block line connector table a-4. Db-25 connector pinout (g.703-hdb3 interface) pin function ...
Page 59
Installation and operation manual appendix a pinouts asm-40 ver. 1.0 db-15 line connector (standalone asm-40) a-7 table a-5. Db-25 and rj-45 pinout, g.703 codirectional pin signal rj-45 db-25 rcv (+) 3 9 rcv (-) 6 11 xmt (+) 4 2 xmt (-) 5 16 gnd 2 7 a.6 db-15 line connector (standalone asm-40) line ...
Page 60
Appendix a pinouts installation and operation manual a-8 db-15 line connector (standalone asm-40) asm-40 ver. 1.0
Page 61: Appendix B
Asm-40 ver. 1.0 ir-eth connector options b-1 appendix b ir-eth interface module ir-eth is an interface module for rad modems, used for converting the ethernet (10baset or 10base2) electrical levels to the modem ttl levels. It also converts the ethernet protocol to hdlc to enable long-distance transm...
Page 62
Appendix b ir-eth interface module installation and operation manual b-2 technical specifications asm-40 ver. 1.0 xmt rcv gnd 10base-2 rx tx coll figure b-3. Asm-40 rear panel with ir-eth/bnc table b-1. Rj-45 connector pinout pin signal 3 rcv (+) 6 rcv (-) 1 xmt (+) 2 xmt (-) – gnd b.2 technical spe...
Page 63
Installation and operation manual appendix b ir-eth interface module asm-40 ver. 1.0 installation and operation b-3 b.3 installation and operation figure b-4 shows the ir-eth layout, the locations of the dip switch, and the rear panel components for the utp version. 1 2 3 4 figure b-4. Ir-eth module...
Page 64
Appendix b ir-eth interface module installation and operation manual b-4 installation and operation asm-40 ver. 1.0 setting the dip switch set the ir-eth dip switch according to table b-2 . Table b-2. Dip switch settings switch number name description default setting 1 sq/fd on – ethernet full-duple...
Page 65
Installation and operation manual appendix b ir-eth interface module asm-40 ver. 1.0 installation and operation b-5 connecting the lan for 10baset installation, either a straight cable or a cross cable may be required. Use a cross cable when connecting to a port that does not implement the crossover...
Page 66
Appendix b ir-eth interface module installation and operation manual b-6 installation and operation asm-40 ver. 1.0
Page 67: Appendix C
Asm-40 ver. 1.0 introduction c-1 appendix c ir-eth/qn (ir-eth/q) interface module c.1 introduction the ir-eth/qn interface module includes a high performance self-learning fast ethernet bridge, which is connected to the lan via a single 10baset or 100baset port, operating in full or half duplex and ...
Page 68
Appendix c ir-eth/qn (ir-eth/q) interface module installation and operation manual c-2 technical specifications asm-40 ver. 1.0 c.2 ir-eth/qn connector figure c-2 shows the rear panel of asm-40, equipped with ir-eth/qn module. Table c-1 lists the module's rj-45 connector pinout. G.703 xmt rcv gnd ac...
Page 69
Installation and operation manual appendix c ir-eth/qn (ir-eth/q) interface module asm-40 ver. 1.0 installation and operation c-3 connector rj-45 wan protocol point-to-point data rate up to 2048 kbps c.4 installation and operation to set the internal switch on the ir-eth/qn interface board, you have...
Page 70
Appendix c ir-eth/qn (ir-eth/q) interface module installation and operation manual c-4 installation and operation asm-40 ver. 1.0 sw2 on 5. 6. 4. 3. 2. An fdx bpr mul nc 1. 100 sw1 5. 7. 6. 8. 4. 3. 2. Lc1 lc2 flc nc nc nc nc 1. Mdi on figure c-3. Location of dip switches sw1 and sw2 setting the dip...
Page 71
Installation and operation manual appendix c ir-eth/qn (ir-eth/q) interface module asm-40 ver. 1.0 installation and operation c-5 table c-3. Dip switch sw2 settings section name description possible settings factory setting 1 100 selects the lan speed on – lan speed is set to 10 mbps off – lan speed...
Page 72
Appendix c ir-eth/qn (ir-eth/q) interface module installation and operation manual c-6 installation and operation asm-40 ver. 1.0 connecting the lan use either a straight cable or a cross cable for the lan connection. Use a cross cable when connecting to a port that does not implement the crossover ...
Page 73: Appendix D
Asm-40 ver. 1.0 introduction d-1 appendix d ir-ip interface module d.1 introduction overview ir-ip is a high-performance, miniature ip router based on rad's unique ip router chip, the chiprouter. Ir-ip works by taking each ethernet frame from the lan and determining whether the ip packet is destined...
Page 74
Appendix d ir-ip interface module installation and operation manual d-2 physical description asm-40 ver. 1.0 application figure d-1 shows a typical application of the asm-40 modem equipped with the ir-ip interface module. Asm-40 with ir-ip asm-40 with v.35 interface router figure d-1. Typical applic...
Page 75
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 physical description d-3 ir-ip leds ir-ip contains three leds, which indicate module activity. Table d-1 lists the leds functions. Table d-1. Ir-ip leds functions name type function int green led on – lan integrity i...
Page 76
Appendix d ir-ip interface module installation and operation manual d-4 physical description asm-40 ver. 1.0 ir-ip dip switch (card version) ir-ip interface module on the card version of asm-40 contains a six-section dip switch, as seen in figure d-3 . Table d-2 lists the dip switch functions. Figur...
Page 77
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 ir-ip management subsystem, general d-5 d.4 ir-ip management subsystem, general introduction the ir-ip interface module management subsystem supports the following functions: • preliminary configuration • configurati...
Page 78
Appendix d ir-ip interface module installation and operation manual d-6 performing preliminary configuration asm-40 ver. 1.0 after configuring ir-ip, it starts normal operation and routes the traffic in accordance with the user-selected configuration parameters. To change the parameters of an alread...
Page 79
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 performing preliminary configuration d-7 4. Establish again communication with ir-ip and continue the preliminary configuration in accordance with the quick setup menu section below. Connecting the telnet host before...
Page 80
Appendix d ir-ip interface module installation and operation manual d-8 performing preliminary configuration asm-40 ver. 1.0 the ip learning mechanism enables ir-ip to learn its lan interface ip address by receiving frames sent by a ping utility to the prescribed lan ip address. To use the ip learni...
Page 81
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 performing preliminary configuration d-9 the err indicator must turn off. At this stage, the communication with ir-ip router is lost, because its ip address has been changed. Therefore, you must reconfigure the desti...
Page 82
Appendix d ir-ip interface module installation and operation manual d-10 ir-ip management utility asm-40 ver. 1.0 no ping replies from ir-ip • if your host does not begin to receive ping replies after three unsuccessful attempts, check the physical connection path between the telnet host ethernet in...
Page 83
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 ir-ip management utility d-11 ir_ip s/w ver. 1.00 31/ir (date) 1. Quick setup 2. Management access 3. Advanced setup 4. Device control 5. View 6. Diagnostic tool (ping terminal) press one of the numbers to select or ...
Page 84
Appendix d ir-ip interface module installation and operation manual d-12 quick setup menu asm-40 ver. 1.0 d.7 quick setup menu the quick setup menu is used to select the main parameters’ values that must be defined before you start using ir-ip. Use the advanced setup menu (see the advanced setup men...
Page 85
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 quick setup menu d-13 asm-40 with ir-ip .6 .5 .4 .3 192.168.1.2 lan ip address: 192.168.1.2 ip address .248 .248 .248 .248 255.255.255.248 mask: 255.255.255.248 mask 192.168.1.1 192.168.1.1 192.168.1.1 192.168.1.1 19...
Page 86
Appendix d ir-ip interface module installation and operation manual d-14 management access menu asm-40 ver. 1.0 read protocol from dip switches selecting yes for this parameter forces ir-ip router card to use the wan protocol selected by section 2 of its dip switch: ppp or frame relay. If you want t...
Page 87
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 advanced setup menu d-15 since the ip router card does not support snmp management, the snmp read community, snmp write community, snmp trap community, and snmp management table parameters are not used. Telnet passwo...
Page 88
Appendix d ir-ip interface module installation and operation manual d-16 advanced setup menu asm-40 ver. 1.0 device identification menu the device identification menu is used to define and store in the ir-ip logistic information: the logical name of ir-ip, information on the contact person and devic...
Page 89
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 advanced setup menu d-17 ir_ip s/w ver. 1.00 31/ir (date) quick setup management access advanced setup ................................................................. Device identification interface parameters ====...
Page 90
Appendix d ir-ip interface module installation and operation manual d-18 advanced setup menu asm-40 ver. 1.0 aging timeout used to specify the time after which inactive lan stations are removed from the ir-ip arp table. A station is defined as inactive when no ip traffic is received from it by the i...
Page 91
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 advanced setup menu d-19 ir_ip s/w ver. 1.00 31/ir (date) quick setup management access advanced setup ..................................................................... Device identification interface parameters ...
Page 92
Appendix d ir-ip interface module installation and operation manual d-20 advanced setup menu asm-40 ver. 1.0 user name to send the name by which an ip router card configured as guest identifies itself. Password to send the password by which an ip router card configured as guest identifies itself. Us...
Page 93
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 advanced setup menu d-21 multicast ip menu the multicast ip menu is used to specify the ip multicast frame forwarding parameters, and to access the static multicast groups’ table. To access the multicast ip menu: • f...
Page 94
Appendix d ir-ip interface module installation and operation manual d-22 device control menu asm-40 ver. 1.0 static groups select this parameter to access the static multicast groups table. The table is used to specify the ip addresses for up to 10 ip multicast groups. You can add, change, or delete...
Page 95
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 device control menu d-23 ir_ip s/w ver. 1.00 31/ir (date) quick setup management access advanced setup device control ---------------------------------------------------------- 1. New software download 2. View error ...
Page 96
Appendix d ir-ip interface module installation and operation manual d-24 device control menu asm-40 ver. 1.0 server ip address used to enter the ip address of the tftp server. File name used to enter the name and path of the file to be transferred from the tftp server. Total timeout used to enter th...
Page 97
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 device control menu d-25 ir_ip s/w ver. 1.00 31/ir (date) quick setup management access advanced setup device control ..................................................................... New software download view e...
Page 98
Appendix d ir-ip interface module installation and operation manual d-26 view menu asm-40 ver. 1.0 d.11 view menu the view menu is used to view the ir-ip configuration data, and display information on its arp tables, multicast groups tables and statistics. To access the view menu: • from the main me...
Page 99
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 view menu d-27 ir_ip s/w ver. 1.00 31/ir (date) view configuration ------------------ boot version :1.06 18.03.1999 device name :ip router card system location :the location of this device contact person :name of con...
Page 100
Appendix d ir-ip interface module installation and operation manual d-28 view menu asm-40 ver. 1.0 to access the multicast groups table screen: • in the view menu, type 3. The multicast groups table screen appears ( figure d-23 ). Ir_ip s/w ver. 1.00 31/ir (date) multicast groups table -------------...
Page 101
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 diagnostic tool (ping terminal) menu d-29 ir_ip s/w ver. 1.00 31/ir (date) system statistics ----------------- counter name val counter name val wan in octets 83504 wan alignment errors 0 wan out octets 1950 wan abor...
Page 102
Appendix d ir-ip interface module installation and operation manual d-30 diagnostic tool (ping terminal) menu asm-40 ver. 1.0 ir_ip s/w ver. 1.00 31/ir (date) quick setup management access advanced setup device control view diagnostic tools (ping terminal) ===========================================...
Page 103
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 erasing user’s configuration d-31 ir_ip s/w ver. 1.00 31/ir (date) quick setup management access advanced setup device control view diagnostic tools (ping terminal) ===================================================...
Page 104
Appendix d ir-ip interface module installation and operation manual d-32 erasing ir-ip software asm-40 ver. 1.0 if you do not set sections 1 and 2 to off within 15 seconds of power-up, the ip router card ignores the setting of all the four sections to on and starts normal operation. In this case, it...
Page 105
Installation and operation manual appendix d ir-ip interface module asm-40 ver. 1.0 erasing ir-ip software d-33 to enable the downloading, ir-ip automatically activates its tftp server application with the following factory-default ip parameters: • ip address: 192.168.205.1 • subnet mask: 255.255.25...
Page 106
Appendix d ir-ip interface module installation and operation manual d-34 erasing ir-ip software asm-40 ver. 1.0
Page 107: Appendix E
Asm-40 ver. 1.0 introduction e-1 appendix e ir-g.703 interface module e.1 introduction ir-g.703 is an interface module for rad modems, converting g.703 64 kbps codirectional signals to ttl levels. The converted data is sent over the modem link using the modem modulation technique and converted back ...
Page 108
Appendix e ir-g.703 interface module installation and operation manual e-2 selecting the ir-g.703 timing asm-40 ver. 1.0 table e-1. Rj-45 connector pinouts pin function 3 rcv (+) 6 rcv (-) 4 xmt (+) 5 xmt (-) 2 gnd e.2 selecting the ir-g.703 timing the ir-g.703 interface module can operate with ext ...
Page 109
Installation and operation manual appendix e ir-g.703 interface module asm-40 ver. 1.0 selecting the ir-g.703 timing e-3 timing source tx data tx tx rx rx rx data g.703 codirectional 64 kbps network fifo ext clock mode rcv clock mode clock in clock out modem a modem b clock recovery data data clk cl...
Page 110
Appendix e ir-g.703 interface module installation and operation manual e-4 selecting the ir-g.703 timing asm-40 ver. 1.0
Page 111: Customer Response Form
24 raoul wallenberg street, tel aviv 69719, israel tel: +972-3-6458181, fax +972-3-6483331, +972-3-6498250 e-mail: erika_y@rad.Com , web site: http://www.Rad.Com customer response form rad data communications would like your help in improving its product documentation. Please complete and return thi...
Page 113
Error report incompatibility with product difficulty in understanding text regulatory information (safety, compliance, warnings, etc.) difficulty in finding needed information missing information illogical flow of information style (spelling, grammar, references, etc.) appearance type of error(s) or...
Page 116
Publication no. 606-200-05/07 international headquarters 24 raoul wallenberg street tel aviv 69719, israel tel. 972-3-6458181 fax 972-3-6498250, 6474436 e-mail market@rad.Com north america headquarters 900 corporate drive mahwah, nj 07430, usa tel. 201-5291100 toll free 1-800-4447234 fax 201-5295777...