- DL manuals
- RAD
- Modem
- ASMi-52
- Installation And Operation Manual
RAD ASMi-52 Installation And Operation Manual
Summary of ASMi-52
Page 1
Asmi-52 installation and operation manual 2/4-wire shdsl modem.
Page 3: Notice
Asmi-52 2/4-wire shdsl modem installation and operation manual notice this manual contains information that is proprietary to rad data communications ltd. ("rad"). No part of this publication may be reproduced in any form whatsoever without prior written approval by rad data communications. Right, t...
Page 4: Limited Warranty
Limited warranty rad warrants to distributor that the hardware in the asmi-52 to be delivered hereunder shall be free of defects in material and workmanship under normal use and service for a period of twelve (12) months following the date of shipment to distributor. If, during the warranty period, ...
Page 5: General Safety Instructions
General safety instructions the following instructions serve as a general guide for the safe installation and operation of telecommunications products. Additional instructions, if applicable, are included inside the manual. Safety symbols this symbol may appear on the equipment or in the text. It in...
Page 6: Handling Energized Products
Handling energized products general safety practices do not touch or tamper with the power supply when the power cord is connected. Line voltages may be present inside certain products even when the power switch (if installed) is in the off position or a fuse is blown. For dc-powered products, altho...
Page 7
Connection of data and telecommunications cables data and telecommunication interfaces are classified according to their safety status. The following table lists the status of several standard interfaces. If the status of a given port differs from the standard one, a notice will be given in the manu...
Page 8: Fcc-15 User Information
To reduce the risk of fire, use only no. 26 awg or larger telecommunication line cords. Pour réduire les risques s’incendie, utiliser seulement des conducteurs de télécommunications 26 awg ou de section supérieure. Some ports are suitable for connection to intra-building or non-exposed wiring or cab...
Page 9
Canadian emission requirements this class a digital apparatus meets all the requirements of the canadian interference-causing equipment regulation. Cet appareil numérique de la classe a respecte toutes les exigences du règlement sur le matériel brouilleur du canada. Warning per en 55022 (cispr-22) t...
Page 11: Quick Start Guide
Configuring asmi-52 1 quick start guide installation of asmi-52 should be carried out only by an experienced technician. If you are familiar with asmi-52, use this guide to prepare the units for operation. 1. Installing asmi-52 connecting the interfaces 1. Connect the line to the rj-45 rear panel co...
Page 12
Quick start guide asmi-52 installation and operation manual 2 configuring asmi-52 configuring the master clock to configure the master clock: • from the system configuration menu (main menu > configuration > system configuration > master clock ), configure the central asmi-52 clock to external or in...
Page 13
Asmi-52 installation and operation manual quick start guide configuring asmi-52 3 to configure e1 parameters: • from the e1 port configuration menu (main menu > configuration > port configuration > e1 port configuration ), configure the following e1 parameters: framing mode timeslot assignment. • yo...
Page 14
Quick start guide asmi-52 installation and operation manual 4 configuring asmi-52.
Page 15: Contents
Asmi-52 installation and operation manual i contents chapter 1. Introduction 1.1 overview..................................................................................................................... 1-1 versions....................................................................................
Page 16
Table of contents ii asmi-52 installation and operation manual configuring the shdsl interface......................................................................................... 4-25 configuring the serial dte interface..............................................................................
Page 17: Chapter 1
Overview 1-1 chapter 1 introduction 1.1 overview asmi-52 is an shdsl modem, which operates in full duplex over 2/4-wire lines and offers a cost-effective solution for delivering digital data to customer premises over the existing copper cables. Asmi-52 handles multiple data rates in the range of 64–...
Page 18
Chapter 1 introduction asmi-52 installation and operation manual 1-2 overview applications figure 1-1 illustrates a typical asmi-52 application, in which standalone modems operate opposite each other. Figure 1-2 shows a typical application of the remote asmi-52 units with a centrally located asmi-52...
Page 19
Asmi-52 installation and operation manual chapter 1 introduction overview 1-3 line interface asmi-52 extends the range of data transmission over 2/4-wire lines up to 7.0 km (4.3 miles), by employing shdsl tc-pam technology. Asmi-52 operation complies with the requirements of the itu-t g.991.2 standa...
Page 20
Chapter 1 introduction asmi-52 installation and operation manual 1-4 overview asmi-52 supports multiple data rates in the range between 64 kbps and 4608 kbps. Data rate depends on the following factors: • unit rate mode (regular or low speed) • line interface type (2-wire or 4-wire) • dte interface ...
Page 21
Asmi-52 installation and operation manual chapter 1 introduction overview 1-5 timing asmi-52 supports three clock modes: • internal, derived from its internal oscillator (co mode) • external, supplied by the attached dte • receive, recovered from the received line signal (cpe mode). Management asmi-...
Page 22
Chapter 1 introduction asmi-52 installation and operation manual 1-6 physical description diagnostics asmi-52 supports activation of the following: • local loopback • remote loopback • remote loopback at shdsl repeater (activated from the local unit). All tests can be activated from the local unit o...
Page 23
Asmi-52 installation and operation manual chapter 1 introduction functional description 1-7 1.3 functional description this section provides a functional description of asmi-52 in the form of block diagrams ( figure 1-4 and figure 1-5 ). Modem glue logic data & clock leds and terminal interface cont...
Page 24
Chapter 1 introduction asmi-52 installation and operation manual 1-8 technical specifications the asmi-52 modem consists of the following major modules: dte interface – prepares the digital data coming from the dte into a data stream for the modem glue logic. In addition it translates the data from ...
Page 25
Asmi-52 installation and operation manual chapter 1 introduction technical specifications 1-9 control port type dte/dce format 8 bits, no parity baud rate 9.6, 19.2, 38.4, 57.6, 115.2 kbps connector 9-pin, d-type female interface 10/100baset ethernet control port protocol mac connector rj-45 timing ...
Page 26
Chapter 1 introduction asmi-52 installation and operation manual 1-10 technical specifications physical plastic enclosure height 43.7 mm / 1.7 in width 240 mm / 9.4 in depth 170.5 mm / 6.7 in weight 0.5 kg / 1.1 lb metal enclosure height 47.3 mm / 1.8 in width 215 mm / 8.4 in depth 147 mm / 5.8 in w...
Page 27: Chapter 2
Site requirements and prerequisites 2-1 chapter 2 installation and setup this chapter describes installation and setup procedures for the standalone asmi-52 modem. After installing the unit: • refer to chapter 3 for the operating instructions. • refer to chapter 4 for the detailed system configurati...
Page 28
Chapter 2 installation and setup asmi-52 installation and operation manual 2-2 installation and setup 2.2 package contents the asmi-52 package includes the following items: • one asmi-52 unit • technical documentation cd • power connection accessories (depending on which power option was ordered): p...
Page 29
Asmi-52 installation and operation manual chapter 2 installation and setup installation and setup 2-3 connecting the interfaces figure 2-1 illustrates the rear panel of asmi-52 in a plastic enclosure with a 4-wire line interface, e1 dte interface, user lan interface, alarm relay port and the control...
Page 30
Chapter 2 installation and setup asmi-52 installation and operation manual 2-4 installation and setup to connect the dte: • connect the dte to the appropriate rear panel dte interface connector of the asmi-52 modem. Appendix a specifies the dte connector pinouts. Connecting the alarm relay connector...
Page 31: Chapter 3
Indicators 3-1 chapter 3 operation this chapter provides the following information for the asmi-52 modem: • asmi-52 front-panel indicators • operating procedures (turn-on, front-panel indications, performance monitoring and turn-off). • asmi-52 default settings. Installation procedures given in chap...
Page 32
Chapter 3 operation asmi-52 installation and operation manual 3-2 operating asmi-52 table 3-1. Asmi-52 front panel leds name function pwr (green) on – power is on tst (red) on – a loopback test is active in local or remote unit sync a (red/green) on (red) – link a is not synchronized on (green) – li...
Page 33
Asmi-52 installation and operation manual chapter 3 operation default settings 3-3 normal indications upon turning on asmi-52, the pwr led in the front panel lights to indicate that asmi-52 is on. Table 3-3 shows the correct status of the indicators a few seconds after the units were synchronized. T...
Page 34
Chapter 3 operation asmi-52 installation and operation manual 3-4 default settings table 3-4. Default settings (cont.) parameter default value telnet allowed access allowed web allowed access allowed bootp state off dts ip address 0.0.0.0 dts ip mask 0.0.0.0 lan operation mode transparent encapsulat...
Page 35
Asmi-52 installation and operation manual chapter 3 operation default settings 3-5 table 3-4. Default settings (cont.) parameter default value shdsl interface transmission mode annex b power backoff enable snext margin disable current margin disable asym psd symmetrical line prob fixed rate note: as...
Page 36
Chapter 3 operation asmi-52 installation and operation manual 3-6 default settings.
Page 37: Chapter 4
Preparing for a control session 4-1 chapter 4 managing asmi-52 via a terminal the configuration of asmi-52 is performed via menu-driven embedded software, using a standard ascii terminal or a pc running a terminal emulation application connected to the rear panel control port. Alternatively, asmi-52...
Page 38
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-2 preparing for a control session preparing the terminal any standard ascii terminal (a “dumb” terminal or a personal computer running a terminal emulation application) equipped with a v.24 (rs-232) communication i...
Page 39
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal preparing for a control session 4-3 figure 4-1. Configurad login managing asmi-52 via dedicated timeslot asmi-52 modems with e1 or t1 interface can be managed via dedicated e1/t1 timeslot (dts) (see figure 4-2 ). The...
Page 40
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-4 navigating the management menus 4.2 navigating the management menus this section provides a general description of the software menu operation and conventions for navigating the menus. Appendix c shows a map of t...
Page 41
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal entering the user name and password 4-5 navigating the configurad menus configurad is a web-based remote access terminal management software. It provides a user-friendly interface for configuring, collecting statisti...
Page 42
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-6 entering the user name and password asmi-52 user name: password: figure 4-3. Password request screen (terminal session) figure 4-4. Password request screen (configurad session) to enter the user name and password...
Page 43
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal displaying the asmi-52 inventory 4-7 figure 4-6. Main menu (configurad session) 4.4 displaying the asmi-52 inventory the asmi-52 inventory displays information on the functional blocks of the local or remote modem. A...
Page 44
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-8 configuring asmi-52 system parameters asmi-52 inventory 1 index 1001 description rad-local asmi-52_m shdsl modem vendor type contained in 0 class 3 rel pos 0 name shdsl modem hw ver 0.00 sw ver 1.00e54 ->> > esc-...
Page 45
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring asmi-52 system parameters 4-9 to display the system configuration menu: • from the configuration menu, select system configuration. The system configuration menu appears (see figure 4-9 ). Asmi-52 system ...
Page 46
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-10 configuring asmi-52 system parameters configuring low speed operation asmi-52 can be configured to work at 64/128 kbps (2-wire) and 64/128/192/256 kbps (4-wire) when operating opposite devices with e1 dte interf...
Page 47
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring asmi-52 system parameters 4-11 2. From the device info menu, select sys contact and enter name of a contact person; select sys location and enter description of the asmi-52 location; select sys name and e...
Page 48
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-12 configuring asmi-52 system parameters 4. Press to return to the management menu (see figure 4-11 ). 5. From the management menu, select save to save your changes. Asmi-52 host ip 1. Host ip address (0.0.0.0) 2. ...
Page 49
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring asmi-52 system parameters 4-13 asmi-52 manager list 1. Mng 1 ip ... (0.0.0.0) 12. Mng 2 mask ... (0.0.0.0) 2. Mng 2 ip ... (0.0.0.0) 13. Mng 3 mask ... (0.0.0.0) 3. Mng 3 ip ... (0.0.0.0) 14. Mng 4 mask ....
Page 50
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-14 configuring asmi-52 system parameters asmi-52 management access 1. Snmp allowed (access allowed) 2. Telnet allowed (access allowed) 3. Web allowed (access allowed) > esc-prev.Menu; !-main menu; &-exit; @-scroll ...
Page 51
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring asmi-52 system parameters 4-15 asmi-52 rem agent table source ip destination ip port 172.17.161.30 255.255.255.255 dts 172.17.161.34 224.0.0.9 dsl 172.17.161.182 224.0.0.9 dsl 172.17.160.104 172.17.161.18...
Page 52
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-16 configuring asmi-52 system parameters asmi-52 lan configuration operation mode (bridge) bridging mode (switching) 1. Bridge table []> 2. Aging timeout(sec)[10 - 1000000] (10) 3. Auto negotiation (enable) 4. Max ...
Page 53
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring asmi-52 system parameters 4-17 6. Select save all to save the changes. 7. Press to exit the editing mode. To remove mac address from the table: 1. From the bridge table, select mac address that you intend...
Page 54
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-18 configuring asmi-52 system parameters asmi-52 data rate (2304 kbps) 1. 64 kbps 12. 768 kbps 23. 1472 kbps 2. 128 kbps 13. 832 kbps 24. 1536 kbps 3. 192 kbps 14. 896 kbps 25. 1600 kbps 4. 256 kbps 15. 960 kbps 26...
Page 55
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring asmi-52 system parameters 4-19 10baset full duplex 100baset half duplex 100baset full duplex. 6. From the lan configuration menu, select save. Configuring fault indication if asmi-52 fault indication is e...
Page 56
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-20 configuring asmi-52 system parameters 3. Select save to save the changes. Asmi-52 rate (9600 kbps) 1. 9600 kbps 2. 19200 kbps 3. 38400 kbps 4. 57600 kbps 5. 115200 kbps > esc-prev.Menu; !-main menu; &-exit; @-sc...
Page 57
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring asmi-52 system parameters 4-21 to access the port control menu: • path: main menu > configuration > control port > port control. The port control menu appears (see figure 4-24 ). Asmi-52 port control 1. P...
Page 58
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-22 configuring asmi-52 system parameters to access terminal menu: • from the port control menu, select terminal. The terminal menu appears (see figure 4-26 ). Asmi-52 terminal 1. Change access > 2. Pop alarm (off) ...
Page 59
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring asmi-52 system parameters 4-23 to configure the security timeout: 1. From the terminal menu, select security timeout to configure the timeout: forever (timeout is disabled) or 10 min (idle disconnect time...
Page 60
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-24 configuring the physical ports 4 to select the dialing mode. Tone, the dial-out modem is instructed to use dtmf dialing. Pulse, the dial-out modem is instructed to use pulse dialing. 5 to control the use of an a...
Page 61
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring the physical ports 4-25 configuring the shdsl interface the asmi-52 configuration software allows you to change the modem’s transmission mode (annex a or annex b). Examples given below illustrate the loca...
Page 62
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-26 configuring the physical ports asmi-52 shdsl local port configuration 1. Power backoff (enable) 2. Snext margin (disable) 3. Current margin (disable) 4. Asym psd (symmetrical) 5. Line prob (adaptive rate) 6. Con...
Page 63
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring the physical ports 4-27 asmi-52 snext margin (disable snext margin) 1. -10 12. 1 2. -9 13. 2 3. -8 14. 3 4. -7 15. 4 5. -6 16. 5 6. -5 17. 6 7. -4 18. 7 8. -3 19. 8 9. -2 20. 9 10. -1 21. 10 11. 0 22. Dis...
Page 64
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-28 configuring the physical ports to configure the power spectral density: 1. From the shdsl port configuration menu, select asym psd to choose the power spectral density value: symmetrical or asymmetrical. The dis...
Page 65
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring the physical ports 4-29 setting the snr margin threshold you can set signal-to-noise ratio threshold. Asmi-52 generates minor alarm (snr margin over line a/b), if the signal-to-noise ratio on the line exc...
Page 66
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-30 configuring the physical ports configuring llb/rlb activation from the dte to enable/disable the llb/rlb activation from the dte: 1. From the physical ports configuration menu, select dte configuration. The dte ...
Page 67
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring the physical ports 4-31 2. Select the data rate by typing the number corresponding to the desired value, and press . The dte port configuration menu appears. 3. Select save to save the changes. Asmi-52 da...
Page 68
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-32 configuring the physical ports to access the e1 port configuration menu: 1. From the physical ports configuration menu, select e1 configuration. The e1 configuration menu appears. 2. From the e1 configuration me...
Page 69
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring the physical ports 4-33 selecting resynchronization time you can define time required for the e1 port operating in the framed mode to normal operation after loss of synchronization: • ccitt – as per requi...
Page 70
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-34 configuring the physical ports mapping e1 timeslots when working with framed e1, you can assign each timeslot to carry data or transmit idle code. To assign the mng timeslot, dts mode must be set to enable (see ...
Page 71
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal configuring the physical ports 4-35 asmi-52 time slot map 1. Ts0 trans 17. Ts16 data 33. Full 2. Ts1 mng 18. Ts17 data 34. Clear 3. Ts2 data 19. Ts18 data 4. Ts3 data 20. Ts19 data 5. Ts4 data 21. Ts20 data 6. Ts5 da...
Page 72
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-36 configuring the physical ports configuring the t1 interface asmi-52 units with t1 interface require configuration of the following parameters: • framing mode: unframed – stream of bits at 1.544 mbps esf – 24 fra...
Page 73
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal displaying the asmi-52 status 4-37 the t1 port configuration menu appears (see figure 4-39 ). Asmi-52 t1 local port configuration 1. Framed mode >(unframed) 2. Line code (b8zs) 3. Receive gain (long) 4. Interface > 5...
Page 74
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-38 displaying the asmi-52 status displaying the system status to display the system information: 1. Display the system status menu. (path: monitoring >system monitoring > system local/remote status) 2. Select syste...
Page 75
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal accessing the remote asmi-52 4-39 asmi-52 port local status shdsl (standard annex unknown, wire mode 2w) shdsl line (status: not sync, state: idle mode) framer type (slotted t1) eoc compatible (standard) actual psd (...
Page 76
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-40 updating software releases 4.9 updating software releases this section presents procedures for installing new software releases into the asmi-52 units, as well as swapping existing software versions in a local o...
Page 77
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal updating software releases 4-41 select tftp total timeout and specify the tftp connection timeout (in seconds). Select save to save the tftp configuration. Select transfer command to start downloading file to asmi-52...
Page 78
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-42 updating software releases to display the software version: 1. From the sw files menu, (file utilities menu > file system > sw files), select local sw files to display software revision of the local asmi-52, or ...
Page 79
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal resetting asmi-52 4-43 4.10 resetting asmi-52 asmi-52 supports four types of reset: • reset to the default setting • shdsl interface reset • shdsl repeater line reset. • overall reset resetting to default settings yo...
Page 80
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-44 resetting asmi-52 resetting the asmi-52 modem you can reset the shdsl interface of the modem or repeater, or perform the overall reset of the modem. To reset the shdsl interface or perform the overall device res...
Page 81
Asmi-52 installation and operation manual chapter 4 managing asmi-52 via a terminal exiting the control session 4-45 3. From the repeater number menu, select repeater that you intend to reset. 4. From the repeater reset menu, select repeater shdsl line reset to reset the shdsl line interface of the ...
Page 82
Chapter 4 managing asmi-52 via a terminal asmi-52 installation and operation manual 4-46 exiting the control session.
Page 83: Chapter 5
Overview 5-1 chapter 5 configuring a typical application 5.1 overview this chapter provides detailed instructions for setting up two asmi-52 modems in a typical application. Configuration of asmi-52 is performed via menu-driven embedded software, using a standard ascii terminal or a pc running a ter...
Page 84
Chapter 5 configuring a typical application asmi-52 installation and operation manual 5-2 configuring the asmi-52 units 5.2 configuring the asmi-52 units two asmi-52 units must be configured for this application. Both units have the same configuration parameters, except for the host ip address and t...
Page 85
Asmi-52 installation and operation manual chapter 5 configuring a typical application configuring the asmi-52 units 5-3 3. Select save to save the changes. To set the device host ip address: 4. Display the host ip menu (main menu > configuration > system configuration > management > host ip. The hos...
Page 86
Chapter 5 configuring a typical application asmi-52 installation and operation manual 5-4 configuring the asmi-52 units asmi-52 shdsl local port configuration 1. Power backoff (enable) 2. Snext margin (disable) 3. Current margin (disable) 4. Asym psd (symmetrical) 5. Line prob (adaptive rate) 6. Con...
Page 87: Chapter 6
Error detection 6-1 chapter 6 troubleshooting and diagnostics this chapter describes the asmi-52 diagnostic functions, which include: • status indications, alarms, power-up self-test • statistics collection • diagnostic tests (loopbacks and leds test). 6.1 error detection power-up self-test asmi-52 ...
Page 88
Chapter 6 troubleshooting and diagnostics asmi-52 installation and operation manual 6-2 error detection remains in the log file, enabling you to view the alarm history. Events enter only the log file. Displaying all alarms asmi-52 allows you to display all alarms, irrespective of their origin (syste...
Page 89
Asmi-52 installation and operation manual chapter 6 troubleshooting and diagnostics error detection 6-3 displaying system alarms to display the system alarms: 1. From the main menu, select monitoring. 2. From the monitoring menu, select system monitoring. The systemmonitoring menu appears (see figur...
Page 90
Chapter 6 troubleshooting and diagnostics asmi-52 installation and operation manual 6-4 error detection 2. Type y and press . All the system log file entries are deleted from the log file. Displaying port alarms 1. Follow the path: main menu > monitoring > physical port monitoring > physical port st...
Page 91
Asmi-52 installation and operation manual chapter 6 troubleshooting and diagnostics error detection 6-5 to display the log file: 1. From the monitoring menu, select physical ports monitoring. The physical ports monitoring menu appears. 2. Select physical port local status to display the local port s...
Page 92
Chapter 6 troubleshooting and diagnostics asmi-52 installation and operation manual 6-6 error detection table 6-1. Asmi-52 alarms and warnings number terminal message port description severity 1 self test error – failure occurred during self-test major 2 software download – software download is in p...
Page 93
Asmi-52 installation and operation manual chapter 6 troubleshooting and diagnostics error detection 6-7 table 6-1. Asmi-52 alarms and warnings (cont.) number terminal message port description severity 26 e1-ts not rate comp t1-ts not rate comp dte current line rate does not support the number of ass...
Page 94
Chapter 6 troubleshooting and diagnostics asmi-52 installation and operation manual 6-8 error detection table 6-1. Asmi-52 alarms and warnings (cont.) number terminal message port description severity 42 wire mode not comp shdsl mismatch between line interface types (2/4-wire) between local and remo...
Page 95
Asmi-52 installation and operation manual chapter 6 troubleshooting and diagnostics displaying shdsl statistics 6-9 table 6-2. Asmi-52 events (cont.) terminal message description gs out of sync abort shdsl framer out of sync gs loss of carrier detect shdsl carrier loss gs sq error detect shdsl signa...
Page 96
Chapter 6 troubleshooting and diagnostics asmi-52 installation and operation manual 6-10 displaying shdsl statistics asmi-52 shdsl statistics 1. Shdsl current performances ... 2. Shdsl all intervals performances ... 3. Shdsl current day performances ... 4. Shdsl all days performances ... 5. Shdsl cl...
Page 97
Asmi-52 installation and operation manual chapter 6 troubleshooting and diagnostics displaying shdsl statistics 6-11 asmi-52 shdsl current day performance port number (1) 24 hour es (0) 24 hour uas (0) 24 hour ses (0) 24 hour lows (0) 24 hour crc (0) cur. Day timer (10 hour) day intervals (10) esc-p...
Page 98
Chapter 6 troubleshooting and diagnostics asmi-52 installation and operation manual 6-12 displaying e1/t1 statistics asmi-52 shdsl all intervals performances ... Interval crc losws es ses uas 1 0 0 0 0 0 esc-prev.Menu; !-main menu; &-exit; ?-help; @-scroll figure 6-12. Shdsl all intervals performanc...
Page 99
Asmi-52 installation and operation manual chapter 6 troubleshooting and diagnostics displaying e1/t1 statistics 6-13 • for the details on enabling the crc-4 function, refer to enabling crc-4 code generation in chapter 4. • for the details on configuring t1 framing, refer to configuring t1 interface ...
Page 100
Chapter 6 troubleshooting and diagnostics asmi-52 installation and operation manual 6-14 displaying e1/t1 statistics asmi-52 e1 current day performance current es (0) current uas (0) current ses (0) current bes (1) current lofc (0) current css (0) 24 hour degrade min (0) 24 hour last degrade min (0)...
Page 101
Asmi-52 installation and operation manual chapter 6 troubleshooting and diagnostics displaying e1/t1 statistics 6-15 table 6-4. E1 statistics parameters (cont.) range display description 15 min 24 hour current uas number of unavailable seconds in which a failed signal occurred during the current int...
Page 102
Chapter 6 troubleshooting and diagnostics asmi-52 installation and operation manual 6-16 performing the diagnostic tests asmi-52 e1 all intervals performances ... Interval es ses uas bes lofc css dm 1 0 0 0 0 0 0 0 esc-prev.Menu; !-main menu; &-exit; @-scroll; ?-help figure 6-18. E1 all intervals pe...
Page 103
Asmi-52 installation and operation manual chapter 6 troubleshooting and diagnostics performing the diagnostic tests 6-17 local dte data local asmi-52 data clock clock line interface glue logic transmit receive figure 6-19. Local loopback to run the local loopback: 1. From the main menu, select diagn...
Page 104
Chapter 6 troubleshooting and diagnostics asmi-52 installation and operation manual 6-18 performing the diagnostic tests asmi-52 local test or remote test llb from dte: off rlb from dte: off 1. Llb (on) 2. Loop timeout (min)(0-4095) ...(5) 3. Leds test 4. Clear all 5. Save > esc-previous menu ; !–ma...
Page 105
Asmi-52 installation and operation manual chapter 6 troubleshooting and diagnostics performing the diagnostic tests 6-19 2. Select rlb. The rlb value in parenthesis changes to on. Also, an additional parameter, loop timeout, is displayed for the local asmi-52. 3. Select loop timeout, if you want to ...
Page 106
Chapter 6 troubleshooting and diagnostics asmi-52 installation and operation manual 6-20 technical support asmi-52 repeater test 1. Rlb network (on) 2. Loop timeout(min)[0 - 4095] ... (5) 3. Repeater number > (1) 4. Save > esc-previous menu ; !–main menu ; &–exit figure 6-24. Repeater test menu deac...
Page 107: Appendix A
Dte interface connectors a-1 appendix a interface connector specifications a.1 dte interface connectors v.35, x.21 and rs-530 interface connectors the v.35 interface of the asmi-52 modem terminates in a 34-pin female connector. The x.21 interface terminates in a 15-pin, d-type female connector. The ...
Page 108
Appendix a interface connector specifications asmi-52 installation and operation manual a-2 dte interface connectors table a-1. V.35, x.21 and rs-530 connector pinouts (cont.) v.35 rs-530 x.21 description 34-pin db-25 db-15 signal function pin circuit pin circuit pin circuit (function) data set read...
Page 109
Asmi-52 installation and operation manual appendix a interface connector specifications dte interface connectors a-3 e1 and t1 interface connector the balanced e1 and t1 interfaces terminate in rj-45 connector. Table a-2 lists the balanced connector pin assignment. Table a-2. E1/t1 connector pinout ...
Page 110
Appendix a interface connector specifications asmi-52 installation and operation manual a-4 control connector a.2 control connector the control terminal interface terminates in a v.24/rs-232 9-pin d-type female connector which can be configured as dce or dte (see the selecting the control port inter...
Page 111
Asmi-52 installation and operation manual appendix a interface connector specifications alarm relay connector a-5 table a-6. Cross cable pinout db-9 pin db-9 pin 2 3 3 2 4 6 5 5 6 4 7 8 8 7 a.3 alarm relay connector the asmi-52 alarm relay terminates in a 9-pin female connector, designated alarm. Fi...
Page 112
Appendix a interface connector specifications asmi-52 installation and operation manual a-6 alarm relay connector.
Page 113: Appendix B
Introduction b-1 appendix b ir-ip interface module table of contents b.1 i ntroduction ..............................................................................................................B-1 overview..............................................................................................
Page 114
Appendix b ir-ip interface module asmi-52 installation and operation manual b-2 introduction b.1 introduction overview ir-ip is a high-performance, miniature ip router based on rad's unique ip router chip, the chiprouter. Ir-ip has a 10baset (utp) interface and complies with ieee 802.3. The router i...
Page 115
Asmi-52 installation and operation manual appendix b ir-ip interface module technical specifications b-3 b.2 technical specifications router local ip net capacity supports up to 256 hosts on the local lan ip net filtering rate 35,000 packets per second ir-ip:technical specifications forwarding rate ...
Page 116
Appendix b ir-ip interface module asmi-52 installation and operation manual b-4 physical description b.3 physical description figure b-2 shows the rear panels of asmi-52 with the ir-ip interface module. Control alarm line b line a 1 4 2 5 act link act link err setup 1 2 3 4 ir-ip e1/t1 shdsl tx rx 1...
Page 117
Asmi-52 installation and operation manual appendix b ir-ip interface module physical description b-5 ir-ip leds ir-ip contains three leds, which indicate the module activity. Table b-3 explains the functions of the ir-ip interface indicators. Table b-3. Ir-ip interface indicators led name function c...
Page 118
Appendix b ir-ip interface module asmi-52 installation and operation manual b-6 ir-ip management subsystem b.4 ir-ip management subsystem the ir-ip interface module management subsystem supports the following functions: • preliminary configuration • configuration of management access parameters • ad...
Page 119
Asmi-52 installation and operation manual appendix b ir-ip interface module performing preliminary configuration b-7 default ip communication parameters the factory-default ip communication parameters of the interface module are: • the default ip address of the ir-ip ethernet port is 192.168.205.1, ...
Page 120
Appendix b ir-ip interface module asmi-52 installation and operation manual b-8 performing preliminary configuration connecting the telnet host before starting the management and configuration activities, it is necessary to establish ip communication between your telnet host and the ir-ip interface ...
Page 121
Asmi-52 installation and operation manual appendix b ir-ip interface module performing preliminary configuration b-9 the ip address is actually retrieved from the arp frames sent during pinging to locate the ping destination, not from the ping frames. To ensure that the process is correctly performe...
Page 122
Appendix b ir-ip interface module asmi-52 installation and operation manual b-10 performing preliminary configuration changing the lan ip address of a configured ir-ip the lan ip address of an already-configured ir-ip can be changed while it operates. This means it is not necessary to turn asmi-52 o...
Page 123
Asmi-52 installation and operation manual appendix b ir-ip interface module ir-ip management utility b-11 b.6 ir-ip management utility general operating procedures the ir-ip interface module is managed via a simple, menu-driven utility that uses a basic terminal user interface. A typical screen is s...
Page 124
Appendix b ir-ip interface module asmi-52 installation and operation manual b-12 quick setup guide menu structure of management utility figure b-4 shows the menu structure of the ir-ip management utility. Main menu 1. Quick setup 1. Lan ip address 2. Lan ip mask 3. Wan ip address 4. Wan ip mask 5. D...
Page 125
Asmi-52 installation and operation manual appendix b ir-ip interface module quick setup guide b-13 2. Enter addresses for lan ip, lan ip mask, wan ip, wan ip mask, default gateway and dhcp server. Lan ip address – the lan ip address for the ip router lan interface, is the address to which nodes conn...
Page 126
Appendix b ir-ip interface module asmi-52 installation and operation manual b-14 quick setup guide to use this option, enter the ip address of another router attached to the local lan in the default gateway field. It is very important to obtain the correct parameters from the system administrator or...
Page 127
Asmi-52 installation and operation manual appendix b ir-ip interface module defining management access b-15 b.8 defining management access the management access menu is used to enable the use of passwords to protect the access to ir-ip management utility, and control the inactivity time-out interval...
Page 128
Appendix b ir-ip interface module asmi-52 installation and operation manual b-16 advanced setup b.9 advanced setup the advanced setup menu is used to select the desired group of ir-ip configuration parameters. The parameters accessed through advanced setup menu supplement the parameters available on...
Page 129
Asmi-52 installation and operation manual appendix b ir-ip interface module advanced setup b-17 ir_ip s/w ver. 1.21 (date) quick setup management access advanced setup ................................................................. Device identification interface parameters =======================...
Page 130
Appendix b ir-ip interface module asmi-52 installation and operation manual b-18 advanced setup defining the wan protocol parameters frame relay protocol the frame relay protocol parameters menu is used to configure the parameters frame relay wan for protocol (the wan protocol is selected by means o...
Page 131
Asmi-52 installation and operation manual appendix b ir-ip interface module advanced setup b-19 ppp protocol menu the ppp protocol parameters menu is used to configure the parameters ppp wan for protocol (the wan protocol is selected by means of the (the wan protocol is selected by means of the quic...
Page 132
Appendix b ir-ip interface module asmi-52 installation and operation manual b-20 advanced setup defining the multicast parameters the multicast ip menu is used to specify the ip multicast frame forwarding parameters, and to access the static multicast groups’ table. To define the multicast parameter...
Page 133
Asmi-52 installation and operation manual appendix b ir-ip interface module using the device control menu b-21 ir_ip s/w ver. 1.21 (date) static multicast groups table ----------------------------- group ip address 1. ................ 2. ................ 3. ................ 4. ................ 5. .....
Page 134
Appendix b ir-ip interface module asmi-52 installation and operation manual b-22 using the device control menu the new software download menu is used to specify the software downloading parameters. To download new software: 1. From the device control submenu, type 1. New software download menu appea...
Page 135
Asmi-52 installation and operation manual appendix b ir-ip interface module using the device control menu b-23 resetting ir-ip the reset menu allows you to perform reset of ir-ip, or its interfaces. This operation can be used to restore normal operation after service is disrupted by an abnormal cond...
Page 136
Appendix b ir-ip interface module asmi-52 installation and operation manual b-24 viewing ir-ip configuration data resetting the wan interface causes the wan controller to be restarted. This results in renegotiation of the wan protocol parameters. To continue your telnet session, press any key within...
Page 137
Asmi-52 installation and operation manual appendix b ir-ip interface module viewing ir-ip configuration data b-25 ir_ip s/w ver. 1.21 (date) view configuration ------------------ boot version :1.06 18.03.1999 device name :ip router card system location :the location of this device contact person :na...
Page 138
Appendix b ir-ip interface module asmi-52 installation and operation manual b-26 viewing ir-ip configuration data ir_ip s/w ver. 1.21 (date) multicast groups table ---------------------- group ip address status group ip address status press any key for exit figure b-21. Multicast groups table screen...
Page 139
Asmi-52 installation and operation manual appendix b ir-ip interface module using diagnostic tools (ping terminal) b-27 ir_ip s/w ver. 1.21 (date) system statistics ----------------- counter name val counter name val wan in octets 83504 wan alignment errors 0 wan out octets 1950 wan aborted frames 0...
Page 140
Appendix b ir-ip interface module asmi-52 installation and operation manual b-28 erasing user’s configuration using the ping function the ping option is used to confirm ip connectivity by pinging other ip hosts. Connectivity is confirmed by receiving a reply from the remote (pinged) ip host. To ping...
Page 141
Asmi-52 installation and operation manual appendix b ir-ip interface module erasing ir-ip software b-29 • when you cannot configure ir-ip because its current lan-interface ip address and/or the telnet password, are not known. To erase the user’s configuration: 1. Turn asmi-52 off. 2. Set all the fou...
Page 142
Appendix b ir-ip interface module asmi-52 installation and operation manual b-30 erasing ir-ip software if you do not set sections 3 and 4 to off within 15 seconds of power-up, ir-ip ignores the setting of all the four sections to on and starts normal operation. In this case, it is recommended to tu...
Page 143
Asmi-52 installation and operation manual appendix b ir-ip interface module erasing ir-ip software b-31.
Page 144: Appendix C
C-1 appendix c configuration menus this appendix lists all menus of the asmi-52 management software. 3. Shdsl repeater configuration 1. Power backoff network side 2. 3. Loop attenuation 4. Snr margin power backoff customer side threshold threshold 5. Repeater number 2. Configuration main menu 1. Inv...
Page 145
Appendix c configuration menus asmi-52 installation and operation manual c-2 some of the management menu options depend on the type of the dte interface installed in asmi-52: • dts configuration (main menu > configuration > management) is available only for the units with e1 or t1 interface. • lan r...
Page 146: Index
I-1 index —a— adapter cable, 1-3 aging timeout, 4-17 alarm relay, 1-9 connecting, 2-4 alarms clearing, 6-3 displaying, 6-2 index of, 6-6 masking, 6-4 asmi-52 menu map, c-1 autonegotiation, 4-18 —b— baud rate, 1-9 bridge table, 4-16 —c— clock modes, 1-5, 4-9 configurad, 1-5 connector dte, a-1 e1/t1, ...
Page 147
Index asmi-52a installation and operation manual i-2 reset wan, b-23 static groups, b-20 statistics, b-26 technical specifications, b-3 —l— lan aging timeout, 4-17 autonegotiation, 4-18 configuration, 4-15 fault indication, 4-19 operation mode, 4-15 rate, 4-17 led test, 6-20 line interface, 1-3, 1-8...
Page 148: Customer Response Form
24 raoul wallenberg st., tel aviv 69719, israel tel: +972-3-6458181, fax: +972-3-6483331, +972-3-6498250 e-mail: , web site: customer response form rad data communications would like your help in improving its product documentation. Please complete and return this form by mail or by fax or send us a...
Page 150: Error Report
Error report type of error(s) ❒ incompatibility with product or problem(s): ❒ difficulty in understanding text ❒ regulatory information (safety, compliance, warnings, etc.) ❒ difficulty in finding needed information ❒ missing information ❒ illogical flow of information ❒ style (spelling, grammar, re...
Page 153
900 corporate drive, mahwah, n.J. 07430, tel: (201) 529-1100 24 raoul wallenberg street, tel aviv 69719, israel, tel: 972-3-6458181 u.S. Headquarters: international headquarters: publication no. 148-201-08/04 www.Rad.Com fax: 972-3-6498250, 972-3-6474436, email: market@rad.Com toll free: 1-800-444-7...