Summary of ZZ Cruiser
Page 1
Owner’s manual.
Page 2
Important note to parents about safe riding your child's safety will depend on your commitment to always provide a safe riding environment and a properly maintained vehicle. As with any moving vehicle there are possible safety risks; be sure to heed to the following precautions. 1. Always equip your...
Page 3
Safety precautions 1. Review all the instructions carefully before operations. 2. Follow all rules and regulations in your area for operating an electric scooter. 3. Do not allow others to use the scooter without proper instructions. 4. Ride only in good weather and on smooth surfaces. 5. Remember t...
Page 4
List of parts m. Throttle - a brake handle - b airless tires - c brake cable - d deck - e front fork - f hub/rim - g kickstand - h folding quick release – i handle bar quick release - j rear tire assembly - k switch box - l tool kit - m 1. Allen wrench (3 different sizes) 2. Wrench (2) 3. Screw driv...
Page 5
Assembly instructions 1. Carefully take your scooter out of the box. 2. Assemble the handle bar. ** see photo’s on page 6 a. Lift handle bar up. Do not put any pressure on the front tire while raising the handle bar. (see figure a) b. Tighten the folding quick release bolt by turning it clockwise. (...
Page 6
(a) (b) (c) (d) 6.
Page 7
Charging 1. Turn power switch in the ‘off’ position. 2. Do not plug the charger into the outlet first, for safety reasons plug the charger cord into the scooter first, then into a 110 v outlet. 3. Charge your scooter for 6-8 hours. The led will be red during charging and once it is fully complete th...
Page 8
Procedure for changing rear tire of zz cruiser • tools required: - phillips screwdriver - 8mm wrench - 2 x 16mm wrench ensure power switch is in the "off" position before beginning any work on the scooter. Fig. 1 step 1) remove the 3 screws from the deck, use the medium size allen wrench to remove s...
Page 9
Fig. 3 step 3.) remove the axle nut located on the right side of the rear tire as seen in fig 3. Fig. 4 step 4.) loosen the brake adjustment bolt as seen in fig 4. Do not completely remove this bolt. It should loosen to the point where the line traveling through the “brake spring” can be removed. Ne...
Page 10
Fig. 5 step 5.) remove the axle bolt from the rear wheel; take not of where the spacers are located. Fig. 6 step 6.) remove the allen bolts from the rim of the tire; you must first cut ½” off of the medium size allen wrench (use hack saw). The rim will split into 2 pieces. Once apart, replace the ol...
Page 11
Fig. 7 step 7.) place the brake shield back on the wheel’s slide axle brake into the tire and remember to place the pacer between the brake shield and brake drum. Fig. 8 step 8.) next place the wheel hub back into the rear fork and reinstall the drive belt. Retighten the axle bolts. 11.
Page 12
Fig. 9 step 9.) insert the “l”-shaped bracket onto the brake shield. The hole for this bracket is located farthest from the wheel axle on the bracket itself. The bracket should be placed on the “tire-side” of the shield (as opposed to the outer side). (wheel shown as removed to better display “l”-sh...
Page 13
Troubleshooting chart problem cause solution the power light by the on/off switch does not light up when the scooter is turned on. 1. Battery is discharged. 2. Loose connection inside the scooter. 1. Recharge your scooter. 2. Remove (3) screws that hold the deck on and remove the deck. Visually insp...
Page 14
List of parts throttle (1) small star screws (2) lock washers (2) drive belt (1) controller (1) brake handle (1) airless tires (2) valve extension (1) brake cable (1) deck (1) front fork (1) front tire assembly (1) hub/rim (2) kickstand (1) motor 300 watt (1) folding quick release (1) handle bar qui...
Page 15
Your insurance policies may not provide coverage for accidents involving the use of this scooter. To determine if coverage is provided, you should contact your insurance company or agent 15.
Page 16
Warranty. Rad2go warrants each new rad2go product for thirty (30) days according to the following terms. This warranty extends to the original retail purchaser only and commences on the date of the original retail purchase. Any part of the rad2go product manufacture or supplied by rad2go and found i...
Page 17
Rad2go electric scooter warranty this warranty registration is to be completed by the dealer or customer at the time of purchase and submitted to rad2go, inc., within 10 days of the date of purchase for warranty entitlement. This warranty is void if the serial number or the safety warning labels on ...
Page 18
3. This warranty does not apply to tire wear, operation under abnormal circumstances or contrary to the requirements described in the owner’s manual or damage to the vehicle brought on by improper use. Racing or competitive use shall void this warranty. 4. Warranty services may be obtained by contra...
Page 19
19 _________ never permit a guest to ride your rad2go electric scooter without reading the owner’s manual and all labels. _________ rad2go electric scooters should not be used by persons unwilling or unable to take responsibility for their actions. _________ read all additional warnings and product ...