Radio Shack 5.8 GHz Cordless Handset Owner's Manual - Using Ac Power

Page of 8

Download

Print this page

Bookmark us

ing AC Power

USING AC POWER

You can power the handset using the

supplied 9V, 210 mA AC adapter.

Insert the

supplied AC

adapter’s barrel

plug into the

IN 9V

jack on

the back of the

charger. Route

the cord

through the

strain relief slot

and plug the

adapter into a standard AC outlet.

CONNECTING/

CHARGING THE

BATTERY

The phone comes with a rechargeable

nickel metal hydride (Ni-MH) battery

pack. Before using your phone, you

must install the battery pack, and then

charge it for about 15-20 hours.

1. Press down and slide the battery

compartment cover off.

CAUTION

You must use

a Class 2

power source

that supplies 9V DC and

delivers at least 210 mA.

Its center tip must be set

to positive and its plug

must fit the charger’s

DC IN 9V jack. The

supplied adapter meets

these specifications.

Using an adapter that

does not meet these

specifications could

damage the handset or

the adapter.

43-3705.fm Page 3 Monday, July 26, 2004 10:14 AM

« ‹ Prev 1 2 3 4 5 6 7 Next › »

Summary of 5.8 GHz Cordless Handset

Page 1
© 2004 radioshack corporation. All rights reserved. Radioshack and radioshack.Com are trademarks used by radioshack corporation. Owner’s manual please read before using this equipment. © 2004 radioshack corporation. All rights reserved. Radioshack and radioshack.Com are trademarks used by radioshack...
Page 2: Selecting A
Sele cting a location 2 the lightning symbol is intended to alert you to the presence of uninsulated dangerous voltage within this product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case. The exclamation symbol is intended to i...
Page 3: Using Ac Power
Us ing ac power 3 using ac power you can power the handset using the supplied 9v, 210 ma ac adapter. ! Insert the supplied ac adapter’s barrel plug into the dc in 9v jack on the back of the charger. Route the cord through the strain relief slot and plug the adapter into a standard ac outlet. Connect...
Page 4: Important
C onnecting/c harging the batt ery 4 2. Plug the battery pack’s connector into the socket in the compartment (the connector fits only one way). Then place the battery pack in the compartment. Place handset on main base to register appears. 3. Replace the cover. To charge the battery pack, place the ...
Page 5: Registering The
R egistering the handset 5 the supplied battery pack should last for about a year. If the battery pack does not hold a charge for more than 2 hours after an overnight charge, replace it with a new 3.6-volt, 750 mah battery pack with a connector that fits the socket in the battery compartment. You ca...
Page 6: Care
Care 6 3. While the handset is registering, handset registering will appear in the lcd. When registration complete is displayed, the handset has been registered to the base. If registration failed appears, please try these steps again. Ô the handset is ready to operate. Use it as described in the ow...
Page 7: The Fcc Wants
Th e fcc wa nts you t o know 7 the fcc wants you to know this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference tha...
Page 8
Radioshack corporation fort worth, texas 76102 43-3705 uuzz01880bz 06a04 printed in china • reorient or relocate the receiving antenna. • increase the separation between the equipment and receiver. • connect the equipment into an outlet on a circuit different from that to which the receiver is conne...