Radio Shack 5W 8 Channel 2-Way Business Band Radio Owner's Manua

Manual is about: 5W 8 Channel 2-Way Business Band Radio

Summary of 5W 8 Channel 2-Way Business Band Radio

  • Page 1

    © 2001 radioshack corporation. All rights reserved. Radioshack and radioshack.Com are trademarks used by radioshack corporation. Owner’s manual — please read before using this equipment. 5w 8 channel 2-way business band radio your radioshack 5w 8 channel 2- way business band radio is a porta- ble, e...

  • Page 2

    2 for other questions concerning the li- cense application, contact the fcc at 717-337-1212, or write: fcc p.O. Box 1040 gettysburg, pa 17325 for the latest fcc application form and instructions, call the fcc's fax-on- demand service at 1-202-418-0177 from a fax machine and request one or more of th...

  • Page 3

    3 during periods of continuous oper- ation. • you must keep a written record of any maintenance or modification made to the transceiver, and you must make this record available for inspection upon demand by the fcc. Violating any of the provisions of part 90 can result in fines and/or confisca- tion...

  • Page 4: A Quick Look At Your Radio

    4 to exceed 50%. In august 1996, the federal communications commis- sions (fcc) adopted rf exposure guidelines with safety levels for hand- held wireless devices. Caution: to maintain compliance with the fcc’s rf exposure guidelines hold the transmitter and antenna at least 2 inches (5 cms) from you...

  • Page 5: Preparation

    5 ˆ preparation charging the battery pack the transceiver comes with an 8.4v, 1300mah rechargeable ni-mh battery pack installed for power. Before you use the battery pack for the first time, you must use the supplied battery charger to charge it for about 14-16 hours. After it is fully charged, the ...

  • Page 6

    6 using an optional handstrap you can attach an optional hand strap (not supplied) to the transceiver. Slide the hand strap’s small loop under the hole at the side of the transceiver. (you might need to use a small screw- driver or a straightened paper clip to do this.) then pull the strap’s large l...

  • Page 7

    7 setting the channels channel 2 is preset to on. Follow these steps to set the channels to on or off. Note: if you do not set any channels besides ch 2 to on and you try to scan the channels, an error tone sounds. (see “selecting a channel” chart on page 10.) 1. To turn off the transceiver, rotate ...

  • Page 8

    8 sions that include the tone. If two different groups operate transceivers in the same area on the same frequen- cy, they do not hear each other’s broadcasts if they both use different quiet codes. Press quiet/q-scan to turn this fea- ture on or off. 48,(7 48,(7 48,(7 48,(7 and the code ap- pear wh...

  • Page 9: Operation

    9 quiet codes ˆ operation rotate off/vol to turn the transceiver on or off and adjust the volume. Hold down ¿ / to scan up through the channels, or À / skip to scan down through the channels. Set quiet/q-scan to the desired code to provide greater communication flexi- bility. If you did not set the ...

  • Page 10

    10 selecting a channel note: you can only select, or scan, channels when you set two or more channels. To manually select a channel , press ¿ / or À / skip . The selected channel number appears. To scan through the channels , hold down ¿ / or À / skip for about 2 sec- onds. 6&$1 6&$1 6&$1 6&$1 appea...

  • Page 11

    11 using key lock you can lock ¿ / , À / skip, quiet/q- scan , and apo/hi/lo on your trans- ceiver to avoid accidentally pressing them. Hold down mon/func , then press lock/ptt to lock or unlock these keys. When these keys are locked, /2&. /2&. /2&. /2&. Ap- pears. If the key tone is on, an error to...

  • Page 12

    Radioshack corporation fort worth, texas 76102 19-1208 63-1120811-a00 02a01 printed in hong kong specifications bandwidth ...................................................................................................................................... 12.5 khz frequency range .....................