1. DL manuals
  2. Radio Shack
  3. Soldering Gun
  4. 64-2185
  5. Owner's Manual

Radio Shack 64-2185 Owner's Manual

Summary of 64-2185

  • Page 1

    Www.Radioshack.Com ™ owner’s manual — please read before using this equipment. 64-2185 © 2002 radioshack corporation. All rights reserved. Radioshack and radioshack.Com are trademarks used by radioshack corporation. &kikvcn"5qnfgtkpi 5vcvkqp thank you for purchasing a radioshack digital soldering st...

  • Page 2

    Importa nt safety instr u ctions 2 +/2146#06" 5#('6;" +05647%6+105" we have taken every precaution in designing this soldering station to ensure that it is as safe as we can make it. However, safe operation depends on you, the operator. We recommend that you follow these simple safety rules. For you...

  • Page 3

    Impor tant safety instruction s 3 • never cover the ventilating slots when using the station. Place the station on a hard, flame resistant base. • always observe the manufacturer’s directions concerning soldering paste, solder creams, and fluxes. • never heat plastic materials or liquids (solvents, ...

  • Page 4: Bottom View

    4 prep aration 24'2#4#6+10" 2. Use a screwdriver to loosen the larger screw at the top of the soldering iron and fully insert the supplied soldering tip into it. Then tighten the screw securely. . . . . ± ± ± ± 3. Insert the soldering iron’s plug into the 5-pole socket on the soldering station. The ...

  • Page 5: –/o

    5 prepa ration 4. Insert the soldering iron into the spring support in the soldering iron stand. 5. Soak the supplied sponge with water and then put it in the tray on the stand. 6. Set –/o at the side of the station to o before plugging it into an ac outlet. & '6#%*+0) " 6*' "5 6#0& 1. Gently pull t...

  • Page 6: –/o

    6 setting the t e mperat ure to reattach the stand, simply place the large tab on the side of the stand in the notch on the side of the station and slide the stand down until it clicks into place. 5'66+0)"6*'" 6'/2'4#674' set the temperature before soldering materials. ± ± ± ± 1. Plug the station in...

  • Page 7: Mode

    S e tting the tempe rature 7 4. Press mode once to change the mode (reading versus setting). 5. The station senses the heating element’s temperature. The soldering tip’s current temperature appears. If the temperature is below 300 ° f (150 ° c), ed ed ed ed appears. ± ± ± ± if the temperature exceed...

  • Page 8

    8 soldering 51.&'4+0) when the soldering iron has reached the desired temperature, you can start to solder. 1. Remove the soldering iron from the stand. 2. Clean the tip on the sponge in the iron stand, so impurities and oxides are removed from the soldering tip. 3. Tin the soldering iron’s tip. ° °...

  • Page 9

    9 r eplacing the f u se 7. Clean and tin the soldering iron. Then put the soldering iron back into the stand. 4'2.#%+0)"6*'" (75' 1. Disconnect the soldering iron from ac power. 2. Use a screwdriver to push and rotate the fuse holder cap on the back of the station counterclockwise. 3. Remove the old...

  • Page 10: Temperature-

    R e setting the s o ldering s tation 10 4'5'66+0)"6*'" 51.&'4+0)" 56#6+10 if the soldering station works improperly or if the display is blank, press temperature- h and temperature- g at the same time to reset the station. %#4' keep the soldering station dry; if it gets wet, wipe it dry immediately....

  • Page 11

    11 spe c ifications 52'%+(+%#6+105 operating voltage ......................... 120v ac/60hz power input ........................................... 80w max. Temperature setting range .......... 350 ° to 840 ° f (200 ° to 450 ° c) display ................................................ 3-digit lcd t...

  • Page 12: Tip Tinner/

    Radioshack corporation fort worth, texas 76102 64-2185 08a02 printed in china 2#465"#0&"#%%'5514+'5 if you need to replace the soldering iron’s tip (cat. No. 910- 3919), the supplied sponge (cat. No. 910-5607), or if you need other parts and accessories, visit your local radioshack store or www.Radi...