- DL manuals
- RadioLink
- Controller
- RC3S
- Instruction Manual
RadioLink RC3S Instruction Manual
Summary of RC3S
Page 1
Digital 4-channel proportional rc system instruction manual radiolink electronics co., ltd http://www.Radiolink.Com.Cn ce fcc rohs *.This manual also appllies to rc4g.
Page 2: Menu
1 1. Introduction and service………………………………………………………….2 2. Safety guides……………………………………………………………….....…. 2 3. Battery recharge notice……………………………………………………..….…3 4. Contents and specifications………………………………………………..…..….4 5. Receiver installation and binding…………………………………………………5 7. Display when power switch ...
Page 3: Important Safety Notice
2 thank you for choosing radiolink rc system, if you are the first time to use this type of products, please read this statement carefully and strictly in accordance with the requirements of operation. You could refer to the manual if you meet any problems during the operation . Please well keep the...
Page 4: Recharge Steps
3 the sequence to shut down is that turn off the receiver power first, and then shut down the transmitter. If the above operations are reverse, it might lead to uncontrolled situation and cause accidents the transmitter needs to be powered by 4 aa alkaline 5# batteries or ni-mh batteries. Please che...
Page 5
106mm 4.6-10 4 contents and specifications ： contents ： 1.Antenna 2.Binding key 3.Channel connection pin specs ： size ： 51.5*24*15 （ mm ） channel number ： 4 channels power standard ： v frequency ： 2.4ghz weight ： 5g contents ： 1. Antenna 2. Lcd 3. Menu key 4. Turning wheel 5. Function key a throttle...
Page 6: Notice
Range, 5 power standard ： 6vdc (1.5aa*4) rf power ： less than 10dbm power extending: jst port 2s~3s lipo/lifepo battery modulation: fhss low voltage alert ： yes （ lower than 4.6v ） data resolution ： 2048 frequency ： 2.4ghz rf range: 300meters on ground failsafe: in 1 second receiver fail getting sig...
Page 7: Display Whenpower
6 was not damaged, large circuit occurred. 4 ． do not cut off or bind the receiver antenna, and try the best to keep it far away from metal and carbon graphite material. 5 ． receiver is made up from precise electronic components, it need to be protected from vibration by packaged with sponge or othe...
Page 8: Powered
Powered button twice, the phase correction is completed. Press code in this situation, short when to the right,wheel left correction. When rotating the car to the left,wheel to observe whether the gyro is correcting wheel. Turn around the car forward direction. , then the code button for once(less t...
Page 9
Lcd screen when you power on the transmitter, lcd screen shows battery voltage, r/c control system name, model name,steering trim,throttle trim model name can store the data for 10 models, model name will show on the lcd when you power on the transmitter. Please make sure the model name the screen d...
Page 10: Model Select "model"
System, 9 both english and chinese version menu are available for which is convenient for chinese and english-speaking players to personalize function menus. 1. Access the function menu (by pressing “exit” and “enter” buttons simultaneously and holding them down for one second), the language select ...
Page 11: End Point Adjustment
) 10 use this when performing left and right steering angle adjustments, throttle high side/brake side operation amount adjustment, and channel 3 servo up side/down side operation amount adjustment during linkage. Correct the maximum steering angle and left and right steering angles when there is a ...
Page 12: Steering Exp "stexp"
11 button to select the desired setting item , press “enter” key the initial value of your selected setting item will blink, then you can press “dec(-)” or “inc(+)” button to adjust the value of your selected setting item. (note: in the interface of adjusting the value, return to the initial value "...
Page 13: Steering Servo Delay
12 3. Press “enter” button, the adjusted value of the rate stops blinking, now the value of the rate has been set. 4.Return to the initial screen by pressing“ exit” button twice. Note:the vertical cursor shown in the figure moves in step with steering wheel operation. Quick steering operation will c...
Page 14: Throttle Curve Adjustment
Ment. The curve can be divided into :five dots throttle curve adjustment,single point adjust- 13 4. Press “enter”button, the adjusted value of the selected setup item stops blinking, now the value of the selected setup item has been set. 5.Return to the initial screen by pressing “exit” button twice...
Page 15
14 “fwd-vtr” function. 2. Press “dec(-)” or “inc(+)” button to select rate for forward side adjustment that you want, when the “mode” value is “int” the vtr will not work, only the “mode” value set to “act” the vtr function is available. From the graph you will clearly see the changes you have made ...
Page 16: Throttle Servo Delay
Throttle 15 side when you want to make the rise milder. (note: in the interface of adjusting the value, return to the initial value"0" by pressing “dec(-)” and “inc(+)” buttons simultaneously for about 1 second.) (2). Press “enter” button, the adjusted brk value stops blinking,now the brkvalue has b...
Page 17
16 function. 2. Press “enter” button to get into thspd function interface. 3.If initial mode setup item is speed1,{ if initial mode setup item is speed 2 or off, you need to select speed 1 by pressing “dec(-)” or “inc(+)” button to select mode setup item , then press “enter” key, speed 2 or off will...
Page 18: Pulse Brake
17 3.If initial mode setup item is speed 2,{ if initial mode setup item is speed 1, you need to select speed 2 by pressing “dec(-)” or “inc(+)” button to select mode setup item , then press “enter” key, speed 1 or off will blink, press “dec(-)” or “inc(+)” button,when the blinking speed 1 or off cha...
Page 19: A.B.S Function Adjustment
18 dly:delay amount cyc: cycle speed tgp:operation point dty:cycle duty ratio stm:steering mixing -abp : amount of brake returnsets the rate at which the ser-vo returns versus trigger oper-ation for brake release. When set to 0%, the abs function is not performed. When set to 50%, the servo returns ...
Page 20
19 select the setting item "abp" by pressing “dec(-)” or “inc(+)” button,then press “enter” key and the initial value of “abp” will blink. Use “dec(-)” or “inc(+)” button to adjust the return amount. (note: in the interface of adjusting the value, return to the initial value"50" by pressing “dec(-)”...
Page 21
20 3. (pulse speed adjustment) select setting item "cyc" by pressing “dec(-)” or “inc(+)” button, then press “enter” key and the initial value of “cyc” will blink. Use “dec(-)” or “inc(+)” button to adjust the pulse speed (cycle). (note: in the interface of adjusting the value, return to the initial...
Page 22
21 (note: in the interface of adjusting the value, return to the initialvalue"0"by pressing “dec(-)” and “inc(+)” buttons simultaneously for about 1 second.) press “enter” button, the adjusted value stops blinking, now the value has been set. "-3":brake application time becomes shortest. (brakes loc...
Page 23: Neutral Position
22 7. When ending setting, return to the initial screen by pressing “exit” button twice. Function which adjusts the movement characteristic from the throttle neutral position the servo will jump to the input position at its maximum possible speed. Unlike exponential, which adjusts the whole throttle...
Page 24: Idle Up At Engine Start
23 initial value: 0 2. (brake side acceleration amount adjustment) press “dec(-)” or “inc(+)” button to select “brak”, press“enter”key to confirm and the initial value of “brak” will blink,then use“dec(-)”or“inc(+)”button adjust the acceleration amount. (note: in the interface of adjusting the value...
Page 25: Subtrim "subtr"
24 1.Enter the function menu and use “dec(-)” or “inc(+) ” button to access idlup function. 2.Press “enter” button to get into idlup function interface. 3.Press “enter” key, and the initial value of rate will blink. Use “ dec(-)” or “inc(+)” button to adjust the value. (note: in the interface of adj...
Page 26: Servo Operation Reversing
25 3. Use “dec(-)” or “inc(+)” button to select st channel, press “enter”key,and the initial value of st will blink. Use “dec(-)” or “inc(+)” button to adjust the center. (note: in the interface of adjusting the value, return to the initial value"0"bypressing “dec(-)” and “inc(+)” buttons simultaneo...
Page 27
26 dual rate the steering left and right servo travels are adjusted simultaneously.When you want to increase the servo travel, adjust the + side.When you want to decrease the servo travel, adjust the – side. Setup item steering d/r rate throttle d/r rate steering d/r rate (rate) 0~100% initial value...
Page 28: Brake Side Adjustment
27 brake side adjustment this function decreases the set value when the braking effect is strongand increases the set value when the braking effect is weak. Setup item rate:brake amount brake amount (rate) 0~100% initial value: 100% 1.Enter the function menu and use “dec(-)” or “inc(+)” button to ac...
Page 29
28 mxmd:mix mode enter the function menu and use “ dec(-)” or “inc(+)” buttonto access pmix function, then press “enter” button to get into pmix function interface. 1.(master channel) channel selection (mst) st, th, ch3 initial value: st select setup item"mst" by pressing “dec(-)” or “inc(+)”button,...
Page 30
29 “dec(-)” and “inc(+)” buttons simultaneously for about 1 second.) press “enter” key, the adjusted value stops blinking,the selected mixing amount has been adjusted. 4.(right, brake or down side mixing amount adjustment) mixing amount -100~0~+100 select the setting item "rght", "brak", or "down"(t...
Page 31: Model Name "name"
30 thechannel 3 and channel 4 servo position can be set from the transmitter.When ch3is assignedto the 3rd channel key,this setting is linked to the key.When ch3 and ch4 is not assigned to the 3 rd channel key, it can be set with this screen. You can also set the ch3 and ch4 as vr at the same time, ...
Page 32: Reset Function "reset"
Lower volt on depands it adjustable, 31 3.After accomplish ment of naming,all characters of current name will stop blinking, the new namewill be stored automatically. 4.When ending setting,return to the initial screenby pressing“exit” button twice.(the new setting model name will appear on the initi...
Page 33
31 be sure to reset press “enter” key, the symbol “yes” will stop blinking, and return to the initial screen. Now the model data is reset to the initial setting that is the default value set at the factory. Not to reset press “dec(-)” or “inc(+)” button, the symbol “yes” will stop blinking and the s...