- DL manuals
- RadioLink
- Remote Control
- T6EAP
- Instruction manual
RadioLink T6EAP Instruction manual
Summary of T6EAP
Page 1
T6eap t6eap for radiolink t6eap 6-channel ppm(fm) modulation radio control system for aircraft instruction manual technical support available at : http://www.Radiolink.Com.Cn radiolink electronic.
Page 2
Table of contents introduction..................................................................................................1 contents and specifications......................................................................................2 glossary..................................................
Page 3
Contents and specifications transmitter: t6eap t6eap transmitter with programmable mixing and 6-model memory. Transmitting on 2,400 mhz band. Operating system: 2-stick, 6-channel system modulation: fhss power supply: 9.6v ni-cd battery or 12v alkaline battery current drain: 250ma receiver: r6eh 6ch ...
Page 4
Introduction to the t6eap system important!: always turn on the transmitter first, then the receiver. When turning off the system, always turn off the receiver first. The object is never to have the receiver on by itself. Otherwise, the servos or control surfaces could be damaged, or in the case of ...
Page 5
Trim levers (all) - used to shift the neutral or center position of each servo as labeled in the diagram. Note: the throttle trim lever is intended for fine tuning the throttle servo when the engine is at idle. Throttle trim does not affect the throttle servo when the throttle control stick is all t...
Page 6
* after the servos are installed, operate each servo over its full travel and check that the pushrods and servo arms do not bind or contact each other. Also make sure the controls do not require excess force to operate. If there is an objectionable buzzing sound coming from a servo, there is probabl...
Page 7
Liquid chip display (lcd) & programming controls mdl 1 ppm 1 10.6 v mode button - use to select desired function while programm data input button - use to input memory or setting. Select button- use to select items within function to be set or changed in the screen power switch modulation indicator ...
Page 8
Programming the t6eap radio anytime you wish to view or change any of the current settings in the transmitter, the programming mode must first be entered by, of course, turning on the power, then by pressing the 2“mode” keys simultaneously and holding them down for one second. Once “in the program” ...
Page 9
3. Choose a character for the first digit by using data input lever. Then move to the next digit by pressing the select key and choose a character in the same way. Continue choosing characters for the third and fourth digits. You can use up to four characters for the name. Revr - servo reversing the...
Page 10
4. Position the dual rate switch where desired for the value you wish to change. 5. Enter the amount of exponential with the data input lever. (as stated above, an exponential value with a “-” in front of it makes the initial servo movement less, or “softer.”) 6. Flip the switch to the other positio...
Page 11
To adjust the trim settings: once the servos and control surfaces have been connected and the control throws have been set using the end points and dual rates, get the model airborne. Adjust the trims as necessary to get the model to fly straight-and-level. If much trim is required on any one contro...
Page 12
Wing mixing type selection with the programmable mix (previously described) the user determines the two channels to be mixed. The wing mixing function is another mix that may be used, but the channels mixed are predetermined. There are three different wing mixing functions to select from: aileron op...
Page 13
Ppm fltr on ppm fltr 0 % 2. If “inh” is blinking, push data input lever upward. Then you will see that the blinking “inh” changes to “on”. Your flap trim is now turned on. 3. Set the travel of the flap control dial at between -100% and +100% by using data input lever. V-tl v-tail mixing intended for...
Page 14
Elvn elevon mixing intended for tailless, “flying wing” models such as delta wings and flying wings, elevon mixing mixes channel 1 (aileron) to channel 2 (elevator) allowing the elevons to operate in unison (as elevators) or in opposition (as ailerons). This function requires that each elevon be ope...
Page 15
Ppm modl i ppm modl 6 [model 2-5] ppm rest clr ppm mol 1 ppm revr i ch [ch 2-5] ppm revr 6 ch ppm d/r i ch 100 % ppm d/r 2 ch 100 % ppm d/r 4 ch 100 % ppm expo 1 ch 0 % ppm expo 2 ch 0 % ppm expo 4 ch 0 % [ch 2-5] ppm epa i ch 100 % ppm epa 6 ch 100 % [ch 2-3] ppm trim i ch 0 % + - ppm trim 4 ch 0 %...
Page 16
Trainer switch to utilize the trainer function, the appropriate trainer cord (available separately) and a second futaba transmitter (usually provided by your flight instructor or r/c club) will be required. When two radios are connected with the trainer cord, they are both capable of operating the m...
Page 17
Each transmitter has an individually assigned, unique id code. In order to start operation, the receiver must be linked with the id code of the transmitter with which it is being paired. Once the link is made, the id code is stored in the receiver and no further linking is necessary unless the recei...
Page 18
T6eap t6eap for radiolink t6eap 6-channel ppm(fm) modulation radio control system for aircraft instruction manual technical support available at : http://www.Radiolink.Com.Cn radiolink electronic.