1. DL manuals
  2. RadiSys
  3. Network Card
  4. ATCA-5400 RTM
  5. Reference

RadiSys ATCA-5400 RTM Reference

Other manuals for ATCA-5400 RTM: Reference
Manual is about: Promentum rear transition module

Summary of ATCA-5400 RTM

  • Page 1

    Www.Radisys.Com promentum ® rear transition module reference atca-5400 007-03301-0000 • august 2009.

  • Page 2

    2 release date description -0000 august 2009 first release. Copyright © 2009 by radisys corporation. All rights reserved. Radisys and promentum are registered trademarks of radisys corporation. Advancedtca, atca, and pigmg are registered trademarks of pci industrial computer manufacturers group. Lsi...

  • Page 3: Table of Contents

    3 table of contents preface ................................................................................................................................................................ 5 about this manual...............................................................................................

  • Page 4

    4 table of contents chapter 4: leds and external interfaces ...................................................................................................... 19 face plate interfaces ...................................................................................................................

  • Page 5: Preface

    5 preface about this manual this manual describes the promentum ® atca-5400, a rear transition module (rtm) that is fully compliant with advancedtca ® (picmg 3.0 advanced telecommunications computing architecture r3.0). The rtm is designed to mate with a compatible front module, such as the atca-450...

  • Page 6

    6 where to get more product information please visit the radisys web site at www.Radisys.Com for product information and other resources. Downloads (manuals, release notes, and software) are available at www.Radisys.Com/downloads . Related promentum manuals the following manuals are available to hel...

  • Page 7

    Electrostatic discharge 7 picmg amc.0 r2.0 advanced mezzanine card base specification , pci industrial computer manufacturers group, november 15, 2006 pm8380 quadsmx 3g quad sata/sas mux/demux for 3g, pmc-2031101 , issue 8, pmc- sierra, april 2005 serial ata revision 2.5 , serial ata international o...

  • Page 8

    8.

  • Page 9: Product Overview

    9 1 product overview this chapter briefly describes the atca-5400 rtm. Block diagram figure 1. Atca-5400 rtm block diagram atca-5400 rtm zone 3 p30 zone 3 p31 +12_rtm +3_3_mp rtm_present note: zone 3 pins that are not shown are not connected . Rtm_en * ipmb-l usb jtag_tck jtag_tdi jtag_tdo jtag_tms ...

  • Page 10

    1 product overview 10 rtm overview the atca-5400 rtm is an optional compatible rear transition module for the atca-4500 cpm front module that supplies the cpm with additional data storage and connectivity options. The rtm has an on-board sas/sata controller and can host an optional sas hard disk dri...

  • Page 11: Installing Frus

    11 2 installing frus installing sfps the rtm has sockets that accept sfp (small form-factor pluggable) transceiver modules. If sfp transceivers are installed, they can provide external connections to the ethernet interfaces. The sockets are located on the face plate of the rtm, as shown in figure 4 ...

  • Page 12

    2 installing frus 12 5. Hold the transceiver near the cable end and turn the connector side to the correct position depending on the rtm orientation: if the rtm is vertical, turn the transceiver so the connector side is on the right. If the rtm is horizontal, turn the transceiver so the connector si...

  • Page 13

    2 installing a hard disk drive 13 attaching the drive sled to the hdd 1. Obey the esd procedures in electrostatic discharge on page 7 and make sure you are adequately grounded. 2. Place the drive sled on a static-free surface with the retaining screw (screw head up) at the left. See figure 2 . 3. Pl...

  • Page 14

    2 installing frus 14 mounting the hard disk drive and sled onto the rtm 1. Align the four sled keyhole screws over the rtm keyholes and simultaneously guide all four screws down into the keyholes. 2. Slide the sled along the keyhole slot toward the rtm face plate and then toward the rtm sas/sata con...

  • Page 15

    15 3 configuring a redundant disk array this chapter explains the rtm’s support for raid (redundant array of inexpensive disks) and how to configure a raid from the available hard disk drives. Hard disk drive arrays can be configured in the sas bios, which is the bios for the sas/sata controller. So...

  • Page 16

    3 configuring a redundant disk array 16 preparing hard disk drives to participate in an array table 1 identifies the locations of hard disk drives that can be used by the rtm sas/sata controller in an array. It also shows the physical sas connection that must be present before you can include the ha...

  • Page 17

    3 configuring a hard disk drive array in the sas bios 17 in figure 3 , the top illustration shows the connections between hard disk drives on two rtms and the cpms in the front slots. The bottom illustration shows the connections between a hard disk drive array and hard disk drives on the rtm, with ...

  • Page 18

    3 configuring a redundant disk array 18 4. Select the raid properties option and press enter. 5. Select the option for the type of raid to create: a. Select create im volume to set up a raid 1 mirroring volume. Select two raid hard disk drives to act as the primary and secondary mirror hard disk dri...

  • Page 19: Leds and External Interfaces

    19 4 leds and external interfaces face plate interfaces the external interfaces on the rtm face plate include a usb port, two external sas ports, an rs-232 serial port, two sfp sockets, and a reset button. Figure 4 shows the location of the interfaces on the rtm face plate. Figure 4. Rtm face plate ...

  • Page 20

    4 leds and external interfaces 20 leds table 2 describes the face plate leds. Table 2. Face plate leds label led id definition color led explanation and states oos led1 out of service red or amber a controlled by the mmc. Red or amber: rtm is oos off: rtm is operating normally pwr led2 power good gr...

  • Page 21

    4 face plate interfaces 21 face plate connectors table 3 describes the face plate connectors on the rtm: reset button the rtm face plate includes a reset button, which causes the rtm mmc to issue a cold reset to the cpm’s ipmc over the ipmb-l. The ipmc then resets the cpm and the rtm payload. The re...

  • Page 22

    4 leds and external interfaces 22 zone 3 interface two zone 3 connectors (p30 and p31) provide the following connections to the rtm: two sas lanes to provide access to a sas hard disk drive on the cpm, connected to: amc port 2 amc port 3 x4 pcie gen2 connection from the cpm (which serves the rtm’s p...

  • Page 23

    4 zone 3 interface 23 alignment keys the rtm is mechanically keyed to prevent accidental insertion of the rtm into an incompatible front module. The zone 2 alignment block (k1) is assigned a keying value of 11. The zone 3 alignment block (k2) is assigned a keying value of 55. Table 5. Rtm connector ...

  • Page 24

    4 leds and external interfaces 24.

  • Page 25: Components and Subsystems

    25 5 components and subsystems sas/sata controller the rtm includes an lsi logic lsisas1064e, which is a serial attached scsi/serial advanced technology attachment (sas/sata) controller. The controller has four sas/sata ports that operate at 3 gbps and connect to the rtm’s optional hard disk drive, ...

  • Page 26

    5 components and subsystems 26 hardware management the rtm includes a module management controller (mmc), which enables the rtm to provide local ipmc functions for self-control and monitoring. The ability to provide these functions makes the rtm an intelligent fru. It connects to the cpm’s local ipm...

  • Page 27

    5 upgradeable components 27 reset the mmc supports the cold reset ipmi command, which can be issued from the cpm (specifying the fru id that corresponds to the rtm). See the atca-4500 compute processing module reference for the correct fru id. An rtm reset includes the sas/sata controller, the pm838...

  • Page 28

    5 components and subsystems 28.

  • Page 29: Specifications

    29 a specifications environmental specifications the rtm is designed to meet the following environmental specifications. The operating environment must provide sufficient airflow across the module to keep it within its temperature specification. Table 7. Environmental specifications characteristic s...

  • Page 30

    A specifications 30 safety specifications the safety specifications are measured under laboratory ambient temperature and humidity (approximately 25c and humidity between 30% and 50%). Testing is performed in partnership with a nationally recognized testing laboratory (nrtl) accredited to provide ...

  • Page 31

    A electromagnetic compatibility (emc) 31 electromagnetic compatibility (emc) the module has been evaluated against the following standards while installed in a representative shelf: emissions standards fcc part 15 (class a digital device) en 55022:2006 + a1 + a2 immunity standards en 55024:1998 + a1...

  • Page 32

    A specifications 32 power consumption fast transient/burst operating en 61000-4-4 0.5 kv, 5/50 ns, 5 khz repetition frequency dc power (host chassis), copper sfp interface. Objective to also evaluate management fe and serial ports. Performance criteria b surge voltages operating en 61000-4-5 (cwg - ...

  • Page 33

    A mean time between failures (mtbf) 33 mean time between failures (mtbf) calculation type: mtbf/fit rate standard: telcordia standard sr-332 issue 2 methods: method i, case iii, quality level ii the calculation results in table 12 were generated using the references and assumptions listed. This spec...

  • Page 34

    A specifications 34.

  • Page 35

    35 b ipmi commands and managed sensors supported ipmi commands the rtm supports the ipmi commands in table 13 . Additional commands can be added if suitable in future versions of the firmware. Table 13. Supported ipmi commands message commands netfn cmd get device id app (0x06) 0x01 broadcast “get d...

  • Page 36

    B ipmi commands and managed sensors 36 managed sensors the rtm manages sensors with sensor data record (sdr) support. The rtm implements a type 12h (0x12) management controller device locator record for identifying the management controller and a type 1h (0x01) full sensor record for describing the ...

  • Page 37

    B managed sensors 37 table 14 shows the threshold definitions. Supported sensors table 15 lists the sensors managed by the mmc. Table 14. Threshold types threshold type description unr upper non-recoverable thresholds generate a critical alarm on the high side. Uc upper critical thresholds generate ...

  • Page 38

    B ipmi commands and managed sensors 38 5 version change version change sensor specific discrete n/a n/a reports version changes as defined in the ipmi v2.0 specification 6 sas1064e temp temp threshold 25 minor, major, critical this sensor measures temperature in °c hysteresis: 2°c default thresholds...