1. DL manuals
  2. RadiSys
  3. Switch
  4. PROMENTUM ATCA-2210
  5. Installation Manual

RadiSys PROMENTUM ATCA-2210 Installation Manual

Manual is about: SWITCH AND CONTROL MODULE

Summary of PROMENTUM ATCA-2210

  • Page 1

    Promentum™ switch and control module installation guide atca-2210 this document describes how to install and to set up the promentum™ atca-2210 switch and control module (scm). Obey esd precautions w arning ! Obey the electrostatic discharge (esd) procedures described at www.Radisys.Com when you ins...

  • Page 2

    Installation guide 2 configuration recommendations standard scm configurations come without sfp or xfp transceivers installed. To protect the internal components of the scm, transceivers or filler plugs must be installed in all empty sockets: the base ethernet configuration supports up to four sfp t...

  • Page 3

    Install sfps or xfps on the scm 3 filler plug installation if xfp or sfp transceivers are removed, install either replacement transceivers or filler plugs in the sockets to protect the internal components of the scm. Additional filler plugs can be ordered from the applicable manufacturer; for a list...

  • Page 4

    Installation guide 4 scm installation checklist the following table describes the possible installation scenarios for the scm, the appropriate tasks to complete for the scenarios, and the order to complete the tasks: scm is being..... Configuration tasks to complete and order to complete them instal...

  • Page 5

    Install the scm in the shelf 5 install the scm in the shelf 1. Follow esd precautions and make sure you are adequately grounded before handling the transceivers and the scm. 2. Remove the scm from its antistatic bag. 3. Open both ejector latches outward. W arning ! Never force open an ejector latch....

  • Page 6

    Installation guide 6 connect to the scm the scm can be accessed by an external computer through the serial and the ethernet maintenance ports. Use the serial port to perform diagnostic and verification procedures or to enable or disable the shelf manager. Use the ethernet maintenance port to connect...

  • Page 7

    Verify switch operation 7 verify switch operation use these steps to view port status and to enable ports on the base ethernet and the fabric ethernet switches. View port status 1. Verify you are at this prompt. Atca-2210# if you are not at the appropriate prompt, see connect to the scm on page 6 fo...

  • Page 8

    Installation guide 8 enable all ports 1. Verify you are at the applicable switch prompt. If you are not at the appropriate prompt, see view port status for instructions on how to get there. 2. Enter this series of commands to enable all ports. A. Configure b. No shutdown all c. Spanning-tree port mo...

  • Page 9

    Verify switch operation 9 b. Enter the specific port (interface) number to enable. The s variable represents the specified slot. The p variable represents an individual port within the group of ports for the specified slot. Interface where s and p have the following values: note: see the atca-5010 s...

  • Page 10

    Installation guide 10 3. Enter the exit command again, to log off the scm. 4. If you have two scms installed, repeat these steps on the other scm. Verify shelf management operation these steps confirm that shelf management is operating when the scm is installed in a radisys shelf. If the scm is inst...

  • Page 11

    Disable the shelf manager on the scm 11 6. To determine the version of scm’s on-board shelf manager, enter: rsys_debug -h 7. After determining the version, enter the appropriate command. 8. Once the software tool has completed its initialization, the host address is displayed. Make a note of this ad...

  • Page 12

    Installation guide 12 enable the shelf manager on the scm if you plan to remove an scm from a non-radisys shelf and reinstall it in a radisys shelf, enable the on-board shelf manager before removing the scm. Important: if the scm is removed from the non-radisys shelf without having its on-board shel...

  • Page 13

    Rear i/o connectivity 13 13. The following text displays: get scm shmgr mode - enter address (in hex): enter the same host address you entered for step 10 . If the on-board shelf manager is disabled, this message displays: scm shmgr mode: enabled 14. Enter q to exit the rsys_debug mode. 15. Remove t...

  • Page 14

    Installation guide 14 where to get more product information please visit the radisys web site at www.Radisys.Com for product information and other resources. Downloads (manuals, release notes, software, etc.) are available via the technical support library product links at www.Radisys.Com/support or...