- DL manuals
- Radyne
- Modem
- MM200
- Installation And Operation Manual
Radyne MM200 Installation And Operation Manual
Summary of MM200
Page 1
Mm200 high speed microwave modem installation and operation manual tm086 - rev. 4.1 comtech ef data • 2114 w 7 th st. • tempe, az 85281 • (480) 333-2200 • fax: (480) 333-2540 • www.Comtechefdata.Com.
Page 3
Mm200 high-speed microwave modem warranty policy tm086 - rev. 4.1 iii warranty policy wp comtech ef data products are warranted against defects in material and workmanship for a period of two years from the date of shipment. During the warranty period, comtech ef data will, at its option, repair or ...
Page 4
Warranty policy mm200 high-speed microwave modem iv tm086 - rev. 4.1 iv before a warranty repair can be accomplished, a repair authorization must be received. It is at this time that comtech ef data will authorize the product or part to be returned to the comtech ef data facility or if field repair ...
Page 5
Mm200 high-speed microwave modem preface tm086 - rev. 4.1 v preface p this manual provides installation and operation information for the radyne rcs20 m:n redundancy switch. This is a technical document intended for use by engineers, technicians, and operators responsible for the operation and maint...
Page 6
Preface mm200 high-speed microwave modem tm086 - rev. 4.1 vi product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Copyright 2008, comtech ef data this manual is proprietary to comtech ef data and is intended for...
Page 7: Toc
Mm200 high-speed microwave modem table of contents tm086 - rev. 4.1 vii table of contents toc warranty policy ............................................................................................................ Iii preface ........................................................................
Page 8
Table of contents mm200 high-speed microwave modem tm086 - rev. 4.1 viii 3.2.2 sample setups __________________________________________________ 3-4 3.2.2.1 transmitting g.703 t3 from interface slot 3 (other interfaces disabled) ___ 3-4 3.2.2.2 transmitting stm-1 from interface slot 1 (other interfac...
Page 9
Mm200 high-speed microwave modem table of contents tm086 - rev. 4.1 ix 4.4.8.2 latched alarms _______________________________________________ 4-28 4.4.8.3 clear alarms _________________________________________________ 4-28 4.4.9 system (menu) _______________________________________________ 4-28 4.4....
Page 10
Table of contents mm200 high-speed microwave modem tm086 - rev. 4.1 x 4.29 server host name ______________________________________________ 4-46 4.30 router ip address _______________________________________________ 4-47 4.31 ip address mask ________________________________________________ 4-47 4.32 ...
Page 11
Mm200 high-speed microwave modem table of contents tm086 - rev. 4.1 xi 5.11.3 ds03 15-pin female hd ‘d’ sub connector (j9) ________________________ 5-8 5.11.4 ds04 15-pin female hd ‘d’ sub connector (j10) _______________________ 5-8 5.11.5 ds05 15-pin female hd ‘d’ sub connector (j11) ______________...
Page 12
Table of contents mm200 high-speed microwave modem tm086 - rev. 4.1 xii section 6 - maintenance and troubleshooting ........................................................ 6-2 6.0 periodic maintenance ______________________________________________ 6-2 6.1 maintenance philosophy ____________________...
Page 13
Mm200 high-speed microwave modem introduction tm086 - rev. 4.1 1-1 introduction 1 1.0 description the radyne mm200 microwave modem is a high-speed, multi data rate modulator/demodulator. It is a single rack digital modem for point-to-point or point-to-multipoint communication links and is ideal for ...
Page 14
Introduction mm200 high-speed microwave modem 1-2 tm086 - rev. 4.1.
Page 15
Mm200 high-speed microwave modem installation tm086 - rev. 4.1 2-1 installation 2 2.0 installation requirements the mm200 is designed to be installed within any standard 19-inch equipment cabinet or rack, and requires 2 rack unit (ru) mounting spaces (3.5 inches) vertically and 19 inches of depth. I...
Page 16
Installation mm200 high-speed microwave modem 2-2 tm086 - rev. 4.1 2.2 removal and assembly if using a knife or cutting blade to open the carton, exercise caution to ensure that the blade does not extend into the carton, but only cuts the tape holding the carton closed. Carefully unpack the unit and...
Page 17
Mm200 high-speed microwave modem installation tm086 - rev. 4.1 2-3 2.4.1 initial power-up before initial power up of the mm200, it is a good idea to disconnect the transmit output from the operating ground station equipment. This is especially true if the current modem configuration settings are unk...
Page 18
Installation mm200 high-speed microwave modem 2-2 tm086 - rev. 4.1.
Page 19
Mm200 high-speed microwave modem theory of operation tm086 - rev. 4.1 3-1 theory of operation 3 3.0 theory of operation the mm200 microwave modem is a highly flexible platform for the transmission of high-speed data across links such as microwave and cable. The 2 ru-rack mount unit can be supplied i...
Page 20
Theory of operation mm200 high-speed microwave modem 3-2 tm086 - rev. 4.1 figure 3-1. Mm200 microwave modem block diagram 3.1.2 data muxiplexer the multiplexer works on a constant output data rate. This data rate is directly related to the symbol rate used by the modulators. The symbol rate is direc...
Page 21
Mm200 high-speed microwave modem theory of operation tm086 - rev. 4.1 3-3 data is always evenly divided between the number of channels selected i.E. Each rf modulator runs at the same rate. 3.1.3 rf modulators the number of active modulators (up to the maximum number installed in the chassis, from 1...
Page 22
Theory of operation mm200 high-speed microwave modem 3-4 tm086 - rev. 4.1 6. Modem should lock with snrs > 32 db. 3.2.2 sample setups 3.2.2.1 transmitting g.703 t3 from interface slot 3 (other interfaces disabled) sample setup 1. In system, user mode, set to ‘level 2’. 2. In modulator, set the frequ...
Page 23
Mm200 high-speed microwave modem theory of operation tm086 - rev. 4.1 3-5 this section is not yet complete. 3.3 calculating 3db bandwidth of mm200 modulated carrier 1. Find the combined interface data rate: dr c = interface 1 data rate + interface 2 data rate + interface 3 data rate + interface 4 da...
Page 24
Theory of operation mm200 high-speed microwave modem 3-6 tm086 - rev. 4.1.
Page 25
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-1 user interfaces 4 4.0 user interfaces there are four user interfaces available for the mm200. These are: front panel control. Command interface control. Terminal interface ethernet snmp any of these methods may be used separately ...
Page 26
User interfaces mm200 high-speed microwave modem 4-2 tm086 - rev. 4.1 4.1.1 front panel lcd display the front panel display is a 2 line by 16-character lcd display. The display is lighted and the brightness can be set to increase when the front panel is currently in use. The lcd display automaticall...
Page 27
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-3 4.1.4 front panel led indicators there are 12 leds on the mm200 front panel to indicate the status of the mm200’s operation (refer to table 4-3). The led colors maintain a consistent meaning. Green signifies that the indication is...
Page 28
User interfaces mm200 high-speed microwave modem 4-4 tm086 - rev. 4.1 4.2 front panel control screen menus the front panel control screen menus are listed below. The mm200 microwave modem may be operated in three different levels: level 0 - is for specialized factory configurations. Every screen is ...
Page 29
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-5 4.3.2 modulator (menu) * the modulator menu screens are listed below: screen name selections and descriptions l2 frequency (hz) {50 – 90 mhz} controls the current center band of the operating frequency width, or the individual cha...
Page 30
User interfaces mm200 high-speed microwave modem 4-6 tm086 - rev. 4.1 4.3.3 demodulator (menu) the demodulator menu screens are listed below: screen name selections and descriptions l2 frequency (hz) {50 – 90 mhz} displays the current center band of the operating frequency width. Rw channels {auto, ...
Page 31
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-7 acq control acq bw (khz) acq delay (sec) reacq delay (sec) acq step (khz) tracking step (hz) of time set in acq delay (sec). 3. Step the demodulator frequency up one step size programmed in acq step (khz). 4. Repeat steps 1 throug...
Page 32
User interfaces mm200 high-speed microwave modem 4-8 tm086 - rev. 4.1 monitor (menu): mux status fifo a status fifo b status channel a err channel b err channel ab err controls the diversity mode. Diversity channel and fifo status. {unused, channel a, channel b, null frames} specifies the multiplexe...
Page 33
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-9 receive (menu): rcv control level (dbm) hysteresis monitor (menu): xmt status rcv status apc receive settings. {rxdown, rxup, auto} controls the remote tx level. Desired rx power level. Apc hysteresis. Apc monitor. {nochange, txdo...
Page 34
User interfaces mm200 high-speed microwave modem 4-10 tm086 - rev. 4.1 clk polarity data invert bb loop volume pids on a framed interface. Note: only appears when using dvb framed interfaces such as l0i. {normal, inverted} sets the polarity of the clock. Note: only appears when supported by the inst...
Page 35
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-11 jit control null pid clk polarity data invert terr loop prbs buff enable clk source clk freq buff depth (ms) note: only appears when supported by the installed interface. {inch, slow, medium, fast, stamp2, stamp3} clock recovery ...
Page 36
User interfaces mm200 high-speed microwave modem 4-12 tm086 - rev. 4.1 press clr to center buffer volume byte gap centers the buffer. {0 - 255} allows the user to set volume level (orderwire only). Note: only appears when supported by the installed interface. {0 - 255} allows the user to set asi byt...
Page 37
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-13 operating frequency width, or the individual channel frequency if the system frequency control is set to ‘user’. Channels {auto, 1 - 4} controls the number of channel cards where 0 = auto, and 1 – 4 = the number of cards. Increas...
Page 38
User interfaces mm200 high-speed microwave modem 4-14 tm086 - rev. 4.1 screen name selections and descriptions l0 l1 l2 frequency (hz) {50 – 90 mhz} displays the current center band of the operating frequency width. Rw rw rw channels {auto, 1 - 4} controls the number of channel cards where 0 = auto,...
Page 39
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-15 acq control acq bw (khz) acq delay (sec) reacq delay (sec) acq step (khz) 1. Try to aquifer at the demodulator programmed frequency. 2. Continue to try to acquire for the length of time set in acq delay (sec). 3. Step the demodul...
Page 40
User interfaces mm200 high-speed microwave modem 4-16 tm086 - rev. 4.1 tracking step (hz) {10 – 100 hz} sets the step size that the demodulator will use to remove the frequency error of a locked signal. Normally set to 10 hz. Rw rw rw diversity (menu): mode monitor (menu): mux status fifo a status f...
Page 41
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-17 4.4.4 repeater (menu) the repeater menu screen is listed below: screen name selections and descriptions l0 l1 l2 mode {off, on} enables the repeater feature. Rw rw rw 4.3.4 apc (menu) the primary apc screen is listed below: scree...
Page 42
User interfaces mm200 high-speed microwave modem 4-18 tm086 - rev. 4.1 the primary tx interface screens and their sub-menus as listed below: screen name selections and descriptions l0 l1 l2 tx intrfc1 (menu): control data rate (bps) interface framing jit control null pid pid clk polarity data invert...
Page 43
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-19 volume implemented, for future expansion. {0 - 255} allows the user to set volume level (orderwire only). Rw rw rw tx intrfc2 (menu) transmit interface 2. Refer to tx intrfc1 (menu) for descriptions. Tx intrfc3 (menu) transmit in...
Page 44
User interfaces mm200 high-speed microwave modem 4-20 tm086 - rev. 4.1 4.4.6 rx interface (menu) the primary rx interface screens and their sub-menus as listed below: screen name selections and descriptions l0 l1 l2 rx intrfc1 control data rate (bps) interface framing jit control null pid pid clk po...
Page 45
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-21 terr loop buff enable clk source clk freq buff depth (ms) press clr to center buffer volume byte gap by the installed interface. {normal, loopback} not yet implemented, for future expansion. {disable, enable} not yet implemented,...
Page 46
User interfaces mm200 high-speed microwave modem 4-22 tm086 - rev. 4.1 tx enabled installed chs off, on} displays tx power control status {0 – 4} displays number of installed channels ro ro ro ro ro ro mon dmd (menu): dmd snr x 10 dmd agc level (dbm) level 1&2 (dbm) level 3&4 (dbm) pre fec1 ber post...
Page 47
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-23 offst frq1 offst frq2 offst frq3 offst frq4 installed chs displays channel 1 offset frequency displays channel 2 offset frequency displays channel 3 offset frequency displays channel 4 offset frequency {0 – 4} displays number of ...
Page 48
User interfaces mm200 high-speed microwave modem 4-24 tm086 - rev. 4.1 event buff {empty, number of events} displays the number of events that has occurred and the event log. The event log is the history of events recorded in the event buffer. A maximum of 40 events may be stored in the buffer. Upon...
Page 49
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-25 mdd1 plllock mdd2 plllock mdd3 plllock {masked, unmasked} rf pll not locked. {masked, unmasked} rf pll not locked. {masked, unmasked} rf pll not locked. Ro ro ro ro ro ro ro ro ro major rx (menu) dmd hw glue dmd hw data signal lo...
Page 50
User interfaces mm200 high-speed microwave modem 4-26 tm086 - rev. 4.1 major dmx (menu) dmx hw fpga int0 hw fpga int2 hw fpga int3 hw fpga int4 hw fpga an alarm that will terminate demux operations. Red led will illuminate. Fpga failure. Fpga failure. Fpga failure. Fpga failure. Fpga failure. Ro ro ...
Page 51
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-27 track fault channel 2 (menu) channel 3 (menu) channel 4 (menu) apc (menu) rcv overrun cmd invalid refer to channel 0 (menu) for descriptions. Refer to channel 0 (menu) for descriptions. Refer to channel 0 (menu) for descriptions....
Page 52
User interfaces mm200 high-speed microwave modem 4-28 tm086 - rev. 4.1 minor int2 (menu) minor int3 (menu) minor int4 (menu) buffer clock pll not locked. Refer to minor int0 (menu) for descriptions. Refer to minor int0 (menu) for descriptions. Refer to minor int0 (menu) for descriptions. Ro ro ro co...
Page 53
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-29 all alarms {no, yes} used for dispersive fading analyzer testing. Rw rw rw date {yy/mm/dd} allows the user to enter the current date. Rw rw rw time {hh:mm:ss} allows the user to enter the current time. Rw rw rw front panel (menu)...
Page 54
User interfaces mm200 high-speed microwave modem 4-30 tm086 - rev. 4.1 fw4459-- fw4459-- firmware version firmware date ro ro ro ro ro ro 4.4.10 test (menu) the test screens are listed below: screen name selections and descriptions l0 l1 l2 led test {on, off} illuminates all leds on front panel. Rw ...
Page 55
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-31 4.5.1 protocol structure when new features are added to radyne inc. Equipment, the control parameters are appended to the end of the non-volatile section of the remote communications specification, and status of the features, if ...
Page 56
User interfaces mm200 high-speed microwave modem 4-32 tm086 - rev. 4.1 the format and structure of the commspec message exchanges are described herein. Decimal numbers have no suffix; hexadecimal numbers end with a lower case h suffix and binary values have a lower case b suffix. Thus, 22 = 16h = 00...
Page 57
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-33 00h + 02h + f0h + 2ah + 09h + 00h + 03h + dfh + feh = 305h. Since the only concern is the modulo 256 (modulo 100h) equivalent (values that can be represented by a single 8-bit byte), the checksum is 05h. For a decimal checksum ca...
Page 58
User interfaces mm200 high-speed microwave modem 4-34 tm086 - rev. 4.1 4.5.4 global response operational codes in acknowledgment response packets, the operational code field of the message packet is set to 0 by the receiving devices when the message intended for the device is evaluated as valid. The...
Page 59
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-35 remote_pid_error 0x0211 remote_data_rate_error 0x0212 remote_interfacetype_error 0x0213 remote_subtype_error 0x0214 remote_clocksource_error 0x0215 remote_clockfrequency_error 0x0216 remote_framing_error 0x0217 remote_volume_erro...
Page 60
User interfaces mm200 high-speed microwave modem 4-36 tm086 - rev. 4.1 remote_symbolrate_perchannel_lo_error 0x0235 remote_symbolrate_perchannel_hi_error 0x0236 remote_notcompatible_error 0x0237 remote_mm200_in_repeater_mode_error 0x0238 remote_diversity_error 0x023a remote_clearber_error 0x023b 4.5...
Page 61
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-37 dmd - 4500/5000 demodulator section 09 rcu - 5000 m:n switch 10 dmd15 modulator 20 dmd15 demodulator 21 dmd15 modem 22 dvb3030 video modulator, dm240 23 reserved for future equipment types 24 – 31 note that multi - drop override ...
Page 62
User interfaces mm200 high-speed microwave modem 4-38 tm086 - rev. 4.1 4.5.7 rllp summary the rllp is a simple send-and-wait protocol that automatically re-transmits a packet when an error is detected, or when an acknowledgment (response) packet is absent. During transmission, the protocol wrapper s...
Page 63
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-39 4.9 mgmt {internet 2} 1.3.6.1.2 this area was reserved to describe objects in the standard mib. As rfcs defining new groups are ratified, the internet assigned numbers authority (iana) assigns new group ids. 4.10 experimental {in...
Page 64
User interfaces mm200 high-speed microwave modem 4-40 tm086 - rev. 4.1 figure 1. Object identifiers in the management information base (sheet 2 of 2) refer to appendix b for mib listing. 4.12 terminal port user interface the terminal port of the mm200 allows for complete control and monitoring of al...
Page 65
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-41 figure 1. 1. Verify that your emulation software is set to the following: vt100 9600 baud 8 data bits no parity 1 stop bit modify the mm200 selection, if necessary, to match the settings (the front panel ‘system’ sub-menu contain...
Page 66
User interfaces mm200 high-speed microwave modem 4-42 tm086 - rev. 4.1 4.15 snmp option 1. From the main menu, select ‘20’ for network configuration. Verify that selection 30, snmp option is enabled. The mm200 snmp option is enabled at the factory if purchased by the user. Please contact the radyne ...
Page 67
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-43 security controls screen: 1.Main menu 2.Control mode : terminal 12.Snmp/security 3.Term emulate : vt 100 13.Logon 4.Term baud : 9600 14.Logoff setup status 5.Traptype : version2 logon user : oper-md5 6.Primarytraphost : 192.168.0...
Page 68
User interfaces mm200 high-speed microwave modem 4-44 tm086 - rev. 4.1 security user logon password authentication password privacy password initial viewer viewer viewer oper–md5 oper oper oper viewer–sha viewer viewer oper-sha oper oper oper note: all entries are case sensitive 4.19 exiting snmp co...
Page 69
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-45 2. In the new password text box, enter the new password (case sensitive, only *’s appear for security). 3. Re-enter the new password to verify the desired setting. 4. Select ok 4.22 logging off 1. To log off the snmp configuratio...
Page 70
User interfaces mm200 high-speed microwave modem 4-46 tm086 - rev. 4.1 3. Re-enter the new password to verify desired setting. 4. Select ok 4.25 modem mm200 high-speed microwave modem ethernet address 1. The modem mm200 high-speed microwave modem ethernet address is configured at the factory. It is ...
Page 71
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-47 this section refers to the boot host. 1. Select 36, ‘server host name’. Enter the server host name and press . This is a descriptive entry only. Example: server 4.30 router ip address select 37, ‘router ip addr’. Enter the router...
Page 72
User interfaces mm200 high-speed microwave modem 4-48 tm086 - rev. 4.1 4.35 trace mode 1. For debugging purposes, a trace mode is specified by the operator users for various diagnostic levels. 4.36 snmp v1 & 2 access view the default access rights for version 1 and 2 snmp users are minimal. They are...
Page 73
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-49 group context/community security level read access write access null mib2 noauth/nopriv system view none viewer mib2 auth/nopriv mib-ii view none viewer dev auth/priv device view none oper mib2 auth/nopriv mib-ii view mib-ii view...
Page 74
User interfaces mm200 high-speed microwave modem 4-50 tm086 - rev. 4.1 4.42 ping program 1. Ping is an application that uses the icmp protocol to report if a host is responding. To check whether the mm200 modem is reachable, use the ping program installed on your computer along with the modem ip add...
Page 75
Mm200 high-speed microwave modem user interfaces tm086 - rev. 4.1 4-51 4.43 snmp test 1. Once it is determined that the mm200 is reachable, compile the custom management information base (mib) for use by the network management station (nms). The mib uses a hierarchical naming scheme. Each managed ob...
Page 76
User interfaces mm200 high-speed microwave modem 4-52 tm086 - rev. 4.1.
Page 77
Mm200 high-speed microwave modem electrical interfaces tm086 - rev. 4.1 5-1 electrical interfaces 5 5.0 mm200 connections all mm200 connections are made to labeled connectors, and to any optional interfaces installed in slots located on the rear of the unit. Any connection interfacing to the mm200 m...
Page 78
Electrical interfaces mm200 high-speed microwave modem 5-2 tm086 - rev. 4.1 refer to table 5-1 below for pinouts for optional dc power plug. Table 5-1. Dc power a - dc input b ground c + dc input 5.2 alarm port the alarm connector (j1) is used to indicate the fault condition of the modulator to exte...
Page 79
Mm200 high-speed microwave modem electrical interfaces tm086 - rev. 4.1 5-3 5.3 terminal port (i/o) the terminal port (j2) can be used for the monitor & control functions of the unit. The physical interface is a female 9-pin d-sub connector. This bi-directional port complies with rs-232 electrical s...
Page 80
Electrical interfaces mm200 high-speed microwave modem 5-4 tm086 - rev. 4.1 5.4.1 remote port cabling for a standard computer rs-232 com port a cable with the following pin-outs is used for remote port communications. Remote port cabling for a standard computer rs-232 com port - 9-pin ‘d’ male compu...
Page 81
Mm200 high-speed microwave modem electrical interfaces tm086 - rev. 4.1 5-5 6 +tx 1 +tx 8 -rx 13 -rx 9 +tx 3 +tx 7 to 12 +rx clk to +tx clk 8 to 11 -rx clk to -tx clk from the overhead to the remote port of the remote modem (cable b) 9-pin ‘d-sub’ 15-pin hd female ‘d-sub’ male 6 -tx 6 -tx 5 gnd 2 gn...
Page 82
Electrical interfaces mm200 high-speed microwave modem 5-6 tm086 - rev. 4.1 5.9 interface slots 1 through 4 several rear panel interfaces are available to slide into the base chassis to suit individual need. The overhead/ds0 audio rear panel interface fits only in interface slot 1 (the upper left sl...
Page 83
Mm200 high-speed microwave modem electrical interfaces tm086 - rev. 4.1 5-7 5.11 overhead/ds0 audio rear panel interface this rear panel interface (figure 5-4) provides eight 64 kbps ds0 interfaces or seven ds0 and one audio channels. Refer to tables 5-6 and 5-7 for pin assignments. Figure 5-4. Over...
Page 84
Electrical interfaces mm200 high-speed microwave modem 5-8 tm086 - rev. 4.1 table 5-7. Channels 2 – 8 (female 15-pin hd ‘d-sub’) ds0 pin signal direction 1 rx_ds0 + out 2 gnd 3 tx_ds0 + in 4 ref_clk + out 5 n/c 6 rx_ds0 - out 7 rx_clk + out 8 tx_clk - in 9 ref_clk - out 10 n/c 11 rx_clk - out 12 tx_...
Page 85
Mm200 high-speed microwave modem electrical interfaces tm086 - rev. 4.1 5-9 5.11.7 ds07 15-pin female hd ‘d’ sub connector (j13) provides channel 7 ds0 interface. 5.11.8 ds08 15-pin female hd ‘d’ sub connector (j14) provides channel 8 ds0 interface. 5.12 optical/oc3 stm-1 rear panel interface this r...
Page 86
Electrical interfaces mm200 high-speed microwave modem 5-10 tm086 - rev. 4.1 5.13 asi rear panel interface this rear panel interface (figure 5-6) provides asynchronous serial interface (asi). Figure 5-6. Asi rear panel interface 5.13.1 asi out female bnc connector (j15) provides asi data output from...
Page 87
Mm200 high-speed microwave modem electrical interfaces tm086 - rev. 4.1 5-11 5.14.2 out female bnc connector (j16) provides e1 data output from the receiver. 5.14.3 balanced 15-pin female ‘d’ sub connector provides t1 data input and output at the following pinouts: table 5-8. Balanced 15 pin female ...
Page 88
Electrical interfaces mm200 high-speed microwave modem 5-12 tm086 - rev. 4.1 5.15.1 parallel tx 25-pin female ‘d’ sub connector (j15) provides rs-422/lvds dvb demodulator output. Table 5-9. Parallel tx rs-422/dvds, dvb – 25-pin female ‘d’ sub connector pin number dvb signal j15 1 clk+ output 14 clk-...
Page 89
Mm200 high-speed microwave modem electrical interfaces tm086 - rev. 4.1 5-13 5.15.2 parallel rx 25-pin female ‘d’ sub connector (j16) accepts rs-422/lvds dvb modulator input. Table 5-10. Parallel rx rs-422/lvds, dvb – 25-pin female ‘d’ sub connector pin number dvb signal direction 1 clk+ input 14 cl...
Page 90
Electrical interfaces mm200 high-speed microwave modem 5-14 tm086 - rev. 4.1 5.16 parallel lvds/dvb, m2p this rear panel interface provides parallel rs-422/lvds m2p data. 5.16.1 parallel tx 25-pin female ‘d’ sub connector (j15) provides rs-422/lvds m2p demodulator output. Table 5-11. Parallel tx rs-...
Page 91
Mm200 high-speed microwave modem electrical interfaces tm086 - rev. 4.1 5-15 5.16.2 parallel rx 25-pin female ‘d’ sub connector (j16) accepts rs-422/lvds m2p modulator output. Table 5-11. Parallel rx rs-422/lvds, m2p – 25-pin female ‘d’ sub connector pin number m2p signal direction 1 outclk+ output ...
Page 92
Electrical interfaces mm200 high-speed microwave modem 5-16 tm086 - rev. 4.1 5.16.4 clk in female bnc connector (j18) accepts the reference clock input. 5.17 smpte/310m rear panel interface this rear panel interface (figure 5-9) provides smpte 310m data. Figure 5-9. Smpte/310m rear panel interface 5...
Page 93
Mm200 high-speed microwave modem electrical interfaces tm086 - rev. 4.1 5-17.
Page 94
Mm200 high-speed microwave modem troubleshooting and maintenance tm086 - rev. 4.1 6-1 maintenance and troubleshooting 6 6.0 periodic maintenance the mm200 contains a lithium battery. Danger of explosion exists if the battery is incorrectly replaced. Replace only with the same or equivalent type reco...
Page 95
Troubleshooting and maintenance mm200 high-speed microwave modem 6-2 tm086 - rev. 4.1 note: if a terminal is available it is easier to view all these parameters on a terminal screen (sw revisions 2.03 and above) see section 4.7 for more information. 6.3 troubleshooting problem: common alarms “glue h...
Page 96
Troubleshooting and maintenance mm200 high-speed microwave modem 6-4 tm086 - rev. 4.1.
Page 97
Mm200 high-speed microwave modem technical specifications tm086 - rev. 4.1 7-1 technical specifications 7 7.0 introduction this section defines the technical performance parameters and specifications for the mm200 high-speed microwave modem. 7.1 specifications total data rate variable from 1 to 200 ...
Page 98
Technical specifications mm200 high-speed microwave modem 7-2 tm086 – rev. 4.1 7.3 optional data interfaces g.703 t3, e3 or sts-1* dvb asi (normal or advanced) rs-422 parallel, dvb parallel, m2p* lvds parallel, dvb parallel, m2p* oc3 optical, stm1/ sts3 electrical* smpte other interfaces available u...
Page 99
Technical specifications mm200 high-speed microwave modem 7-2 tm086 - rev. 4.1.
Page 101
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-1 remote rllp a when new features are added to radyne equipment, the control parameters are appended to the end of the non-volatile section of the remote communications specification, and status of the features, if any, are added at the ...
Page 102
Appendix a mm200 high-speed microwave modem a-2 tm086 – rev. 4.1 configuration query mod tx enable 0x2054 returns the carrier enable status query mod tx carrier 0x2055 returns the carrier mode query mod channel status 0x2070 query selected modulator channel status query mod channel configuration 0x2...
Page 103
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-3 command repeater mode 0x220d selects the repeater mode command mod frequency 0x2240 set modulator frequency command mod data rate 0x2241 set modulator data rate command mod symbol rate 0x2242 set modulator symbol rate command mod modul...
Page 104
Appendix a mm200 high-speed microwave modem a-4 tm086 – rev. 4.1 a.3 detailed command descriptions opcode: query identification query response modem device id mm200 = 32 (0x20) opcode: query current mm200 control mode query response mode 0 = local 1 = terminal 2 = computer 3 = ethernet opcode: query...
Page 105
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-5 second 0 – 59 opcode: query current summary alarms query response modem summary fault mod summary fault demod summary fault bit 0 = mm200 global summary fault, set when the mm200 is faulted bit 1 = modulator summary fault, set when the...
Page 106
Appendix a mm200 high-speed microwave modem a-6 tm086 – rev. 4.1 demod summary fault bit 0 = demodulator fault bit 1 = demodulator channel 1 fault bit 2 = demodulator channel 2 fault bit 3 = demodulator channel 3 fault bit 4 = demodulator channel 4 fault bit 5 = demodulator interface 1 fault bit 6 =...
Page 107
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-7 query response selected channel number channel major alarm status channel minor alarm status channel latched major alarm status channel latched minor alarm status channel baud rate baud state reserved 0 = channel1 1 = channel2 2 = chan...
Page 108
Appendix a mm200 high-speed microwave modem a-8 tm086 – rev. 4.1 query response selected channel number channel major alarm mask channel minor alarm mask 0 = channel1 1 = channel2 2 = channel3 3 = channel4 0 = mask, 1 = allow bit 0 = mod daughter board fpga status bit 1 = rf pll lock detect status b...
Page 109
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-9 channel major alarm mask channel minor alarm mask 0 = mask, 1 = allow bit 0 = mod daughter board fpga status bit 1 = rf pll lock detect status bit 2 - 7 = spare 0 = mask, 1 = allow bit 0 = loop lock status bit 1 = fec lock status bit 2...
Page 110
Appendix a mm200 high-speed microwave modem a-10 tm086 – rev. 4.1 query response major alarm1 status major alarm2 status minor alarm1 status minor alarm2 status common alarm1 status common alarm2 status latched major alarm1 status latched major alarm2 status latched minor alarm1 status latched minor...
Page 111
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-11 utilization bandwidth apc minimum tx level % utilization, implied decimal point (i.E. 7985 means 79.85%) current bandwidth usage minimum apc transmit level (not yet implemented) opcode: query a modulator’s configuration query response...
Page 112
Appendix a mm200 high-speed microwave modem a-12 tm086 – rev. 4.1 minor alarm2 mask common alarm1 mask common alarm2 mask control mode prbs last rate control user mode apc control apc maximum tx level apc default tx level apc speed apc step size apc range bit 3 – 7 = spare 0 = mask, 1 = allow bit 0 ...
Page 113
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-13 bytes to index into the selected channel status area. The nonvolatile data might grow with future firmware revisions. Refer to discussion on forward/backward compatibility. Data rate symbol rate if frequency transmit power carrier con...
Page 114
Appendix a mm200 high-speed microwave modem a-14 tm086 – rev. 4.1 minor alarm2 mask common alarm1 mask common alarm2 mask control mode prbs last rate control user mode apc control apc maximum tx level apc default tx level apc speed apc step size apc range bit 3 – 7 = spare 0 = mask, 1 = allow bit 0 ...
Page 115
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-15 minor alarm1 status minor alarm2 status common alarm1 status common alarm2 status latched major alarm1 status latched major alarm2 status latched minor alarm1 status latched minor alarm2 status latched common alarm1 status latched com...
Page 116
Appendix a mm200 high-speed microwave modem a-16 tm086 – rev. 4.1 query response diversity mux status diversity fifo a status diversity fifo b status reserved channel a error counter channel b error counter channel ab error counter 0 = unused, 1 = channel a, 2 = channel b, 3 = null framer 0 = no fla...
Page 117
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-17 channel baud rate channel offset frequency channel agc integrator channel snr channel cba channel uba input level pre fec ber post fec ber bit 3 = fifo empty status bit 4 = sync lock status bit 5 = fifo reload status bit 6 = fifo pos ...
Page 118
Appendix a mm200 high-speed microwave modem a-18 tm086 – rev. 4.1 bit 7 = track fault status opcode: query a selected demodulator’s channel configuration and status command data field 1 byte selected channel number 0 = channel1 1 = channel2 2 = channel3 3 = channel4 query response selected channel n...
Page 119
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-19 channel latched major alarm status channel latched minor alarm status channel baud rate channel offset frequency channel agc integrator channel snr channel cba channel uba input level pre fec ber post fec ber bit 3 = fifo empty status...
Page 120
Appendix a mm200 high-speed microwave modem a-20 tm086 – rev. 4.1 status minor alarm1 status minor alarm2 status common alarm1 status common alarm2 status latched major alarm1 status latched major alarm2 status latched minor alarm1 status latched minor alarm2 status latched common alarm1 status latc...
Page 121
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-21 if frequency if separation demodulation spectrum channel setting major alarm1 mask major alarm2 mask minor alarm1 mask minor alarm2 mask common alarm1 mask common alarm2 mask control mode last rate control user mode 50000000 - 9000000...
Page 122
Appendix a mm200 high-speed microwave modem a-22 tm086 – rev. 4.1 acquisition control acquisition bandwidth acquisition delay acquisition step tracking step re-acquisition delay apc control apc hysteresis apc level 3 = level 2 0 = off, 1 = acquire 50 – 400 khz, 1 khz steps 10 – 255 sec, 1 sec steps ...
Page 123
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-23 channel setting major alarm1 mask major alarm2 mask minor alarm1 mask minor alarm2 mask common alarm1 mask common alarm2 mask control mode last rate control user mode acquisition control acquisition bandwidth acquisition delay acquisi...
Page 124
Appendix a mm200 high-speed microwave modem a-24 tm086 – rev. 4.1 apc control apc hysteresis apc level sets the apc receive control (not yet implemented) sets the apc receive hysteresis level (not yet implemented) sets the apc receive level in dbm (not yet implemented) status bytes major alarm1 stat...
Page 125
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-25 status max payload utilization bandwidth input level maximum payload at current demodulation % utilization. Implied decimal point (i.E. 7985 means 79.85%) current bandwidth usage aggregate input level in dbm. Signed implied decimal po...
Page 126
Appendix a mm200 high-speed microwave modem a-26 tm086 – rev. 4.1 reserved 5 = t1e1 6 = dso 7 = par 8 = oc3 9 = hssi 10 = smpte 11 = p10baset 12 = t2e2 spare opcode: query selected tx interface configuration command data field 1 byte selected interface number 0 = interface1 1 = interface2 2 = interf...
Page 127
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-27 interface volume interface clock polarity interface data polarity interface baseband loopback reserved interface prbs interface major alarm1 mask interface minor alarm1 mask 1 = mpeg 188 2 = mpeg 204 0 = 255 0 = normal 1 = inverted 2 ...
Page 128
Appendix a mm200 high-speed microwave modem a-28 tm086 – rev. 4.1 bytes to index into the selected interface status area. The nonvolatile data might grow with future firmware revisions. Refer to discussion on forward/backward compatibility. Interface pid interface data rate interface control interfa...
Page 129
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-29 reserved interface prbs interface major alarm1 mask interface minor alarm1 mask spare 0 = normal 1 = prbs_23 2 = prbs_23m 3 = prbs_15 4 = prbs_15m (not yet implemented) 0 = mask, 1 = allow bit 0 = interface test bit 1 - 7 = spare 0 = ...
Page 130
Appendix a mm200 high-speed microwave modem a-30 tm086 – rev. 4.1 reserved 4 = t3e3 5 = t1e1 6 = dso 7 = par 8 = oc3 9 = hssi 10 = smpte 11 = p10baset 12 = t2e2 spare opcode: query selected tx interface jitter control command data field 1 byte selected interface number 0 = interface1 1 = interface2 ...
Page 131
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-31 minor alarm1 status interface card reserved bit 0 = interface fifo full bit 1 = interface fifo empty bit 2 = pll lock bit 3 = interface data activity detect bit 4 = interface clock activity detect bit 5 - 7 = spare 0 = none 1 = asi/aa...
Page 132
Appendix a mm200 high-speed microwave modem a-32 tm086 – rev. 4.1 interface sub type interface clock source interface clock frequency interface framing interface volume interface clock polarity interface data polarity reserved interface terrestrial loopback interface prbs interface major alarm1 mask...
Page 133
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-33 bit 5 - 7 = spare opcode: query selected rx interface configuration and status command data field 1 byte selected interface number 0 = interface1 1 = interface2 2 = interface3 3 = interface4 query response selected interface number nu...
Page 134
Appendix a mm200 high-speed microwave modem a-34 tm086 – rev. 4.1 interface sub type interface clock source interface clock frequency interface framing interface volume interface clock polarity interface data polarity reserved interface terrestrial loopback interface prbs interface major alarm1 mask...
Page 135
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-35 interface latched major alarm1 status interface latched minor alarm1 status interface card reserved bit 1 = interface fifo empty bit 2 = pll lock bit 3 = interface data activity detect bit 4 = interface clock activity detect bit 5 - 7...
Page 136
Appendix a mm200 high-speed microwave modem a-36 tm086 – rev. 4.1 selected interface number 0 = interface1 1 = interface2 2 = interface3 3 = interface4 query response selected interface number byte gap 0 = interface1 1 = interface2 2 = interface3 3 = interface4 0 = burst mode, 1..255 = byte gap opco...
Page 137
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-37 opcode: command set common alarm mask command data common alarm1 mask common alarm2 mask 0 = mask, 1 = allow bit 0 = glue logic fpga fail bit 1 = test fpga fail bits 2 – 7 = spare 0 = mask, 1 = allow bit 0 – 7 = spare opcode: command ...
Page 138
Appendix a mm200 high-speed microwave modem a-38 tm086 – rev. 4.1 opcode: command modulator symbol rate command data symbol rate 3500000 - 28000000 opcode: command modulator modulation command data modulation 0 = qam4 1 = qam16 2 = qam32 3 = qam64 4 = qam128 5 = qam256 opcode: command modulator spec...
Page 139
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-39 opcode: command modulator carrier mode command data carrier mode 0 = normal 1 = cw 2 = offset 1hz 3 = 100khz 4 = 3.5mhz 5 = sweep up 6 = sweep down opcode: command modulator if separation command data if separation 100 - 150% opcode: ...
Page 140
Appendix a mm200 high-speed microwave modem a-40 tm086 – rev. 4.1 channel minor alarm mask bit 2 - 7 = spare 0 = mask, 1 = allow bit 0 = loop lock status bit 1 = fec lock status bit 2 = fifo full status bit 3 = fifo empty status bit 4 = fifo active status bit 5 - 7 = spare opcode: command selected t...
Page 141
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-41 interface data polarity interface baseband loopback reserved interface prbs interface major alarm1 mask interface minor alarm1 0 = normal, 1 = inverted 0 = disable, 1 = enable spare 0 = normal 1 = prbs_23 2 = prbs_23m 3 = prbs_15 4 = ...
Page 142
Appendix a mm200 high-speed microwave modem a-42 tm086 – rev. 4.1 demodulation 0 = qam4 1 = qam16 2 = qam32 3 = qam64 4 = qam128 5 = qam256 opcode: command demodulator spectrum command data spectrum 0 = normal, 1 = inverted opcode: command demodulator alarm mask command data major alarm1 mask major ...
Page 143
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-43 opcode: command demodulator bandwidth command data bandwidth available bandwidth note: command is only allowed in level 2 user mode. Along with the selected interfaces, and the number of channels, the modem calculates all relevant sys...
Page 144
Appendix a mm200 high-speed microwave modem a-44 tm086 – rev. 4.1 bit 4 = sync lock status bit 5 = fifo reload status bit 6 = fifo pos status bit 7 = track fault status opcode: command selected rx interface configuration command data selected interface number interface pid interface data rate interf...
Page 145
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-45 framing interface volume interface clock polarity interface data polarity reserved interface terrestrial loopback interface prbs interface major alarm1 mask interface minor alarm1 mask 1 = mpeg 188 2 = mpeg 204 3 = null 188 4 = null 2...
Page 146
Appendix a mm200 high-speed microwave modem a-46 tm086 – rev. 4.1 byte gap 3 = interface4 0 = burst mode, 1..255 = byte gap.
Page 147
Mm200 high-speed microwave modem appendix a tm086 – rev. 4.1 a-47.
Page 149
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-1 snmp mib b mm200-mib definitions ::= begin imports enterprises from rfc1155-smi module-identity, object-type from snmpv2-smi; mm200 module-identity last-updated "200611011000z" organization "radyne inc. Inc." contact-info "customer serv...
Page 150
Appendix b mm200 high-speed microwave modem b-2 tm086 – rev. 4.1 -- ------------------------------------------------------------------------------------------------------------------- -- textual conventions controltype ::= textual-convention status current description "represents a boolean control v...
Page 151
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-3 description "selects if user 2 frequency in hz." ::= { radmm200modnvstatus 5 } radmm200txifuser3frequency object-type syntax integer (50000000..90000000) max-access read-write status current description "selects if user 3 frequency in h...
Page 152
Appendix b mm200 high-speed microwave modem b-4 tm086 – rev. 4.1 description "inverts the direction of rotation for the modulation." ::= { radmm200modnvstatus 12 } radmm200txcarriermode object-type syntax integer { normal(1), cw(2), offset1hz(3), khz100(4), mhz35(5), sweepup(6), sweepdown(7) } max-a...
Page 153
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-5 description "minor alarm 1 mask: bit 0 = tx clock activity detect bit 1 = tx data activity detect bit 2 = frame lock bit 3 = spare bit 4 = spare bit 5 = spare bit 6 = spare bit 7 = spare 0 = mask, 1 = allow" ::= { radmm200modnvstatus 17...
Page 154
Appendix b mm200 high-speed microwave modem b-6 tm086 – rev. 4.1 radmm200txminoralarm1status object-type syntax alarmbytetype max-access read-only status current description "a bit field. On startup, the agent initializes this to the value '00000000'b bit 0 = tx clock activity detect bit 1 = tx data...
Page 155
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-7 bit 7 = spare 0 = pass, 1 = fail" ::= { radmm200modstatus 7 } radmm200txlatchedminoralarm2status object-type syntax alarmbytetype max-access read-only status current description "a bit field. On startup, the agent initializes this to th...
Page 156
Appendix b mm200 high-speed microwave modem b-8 tm086 – rev. 4.1 "mm200 tx channel non-volatile status structure" index { radmm200txchannelnvindex } ::= { radmm200txchannelnvstatustable 1 } radmm200txchannelnvstatusentry ::= sequence { radmm200txchannelnvindex integer, radmm200txchannelmajoralarmmas...
Page 157
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-9 radmm200txchannelstatusentry ::= sequence { radmm200txchannelindex integer, radmm200txchannelmajoralarmstatus integer, radmm200txchannelminoralarmstatus integer, radmm200txchannellatchedmajoralarmstatus integer, radmm200txchannellatched...
Page 158
Appendix b mm200 high-speed microwave modem b-10 tm086 – rev. 4.1 bit 3 = fifo empty status bit 4 = fifo active bit 5-7 = spares 0 = pass, 1 = fail" ::= { radmm200txchannelstatusentry 5 } radmm200txchannelbaudrate object-type syntax integer (7000000..200000000) max-access read-only status current de...
Page 159
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-11 radmm200txinterfacemajoralarmmask integer, radmm200txinterfaceminoralarmmask integer, radmm200txinterfacejittercontrol integer } radmm200txinterfacenvindex object-type syntax integer (1..4) max-access read-only status current descripti...
Page 160
Appendix b mm200 high-speed microwave modem b-12 tm086 – rev. 4.1 smpt19(15) smpt38(16) } max-access read-write status current description "selects the tx interface type." ::= { radmm200txinterfacenvstatusentry 5 } radmm200txinterfacesubtype object-type syntax integer { spare(1) } max-access read-wr...
Page 161
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-13 ::= { radmm200txinterfacenvstatusentry 11 } radmm200txinterfaceprbs object-type syntax integer { normal(1), ones(2), pat001(3), prbs2047(4) } max-access read-write status current description "selects the pseudo-random bit sequence for ...
Page 162
Appendix b mm200 high-speed microwave modem b-14 tm086 – rev. 4.1 radmm200txinterfacestatusentry object-type syntax radmm200txinterfacestatusentry max-access not-accessible status current description "mm200 tx interface volatile status structure" index { radmm200txinterfaceindex } ::= { radmm200txin...
Page 163
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-15 radmm200txinterfacelatchedminoralarmstatus object-type syntax alarmbytetype max-access read-only status current description "minor alarm status: bit 0 = interface fifo full bit 1 = interface fifo empty bit 2 = interface pll lock bit 3 ...
Page 164
Appendix b mm200 high-speed microwave modem b-16 tm086 – rev. 4.1 radmm200rxifuser3frequency object-type syntax integer (50000000..90000000) max-access read-write status current description "selects if user 3 frequency in hz." ::= { radmm200demodnvstatus 4 } radmm200rxifuser4frequency object-type sy...
Page 165
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-17 ::= { radmm200demodnvstatus 10 } radmm200rxchannelsetting object-type syntax integer { auto(1), onechannel(2), twochannel(3), threechannel(4), fourchannel(5) } max-access read-write status current description "selects the total number ...
Page 166
Appendix b mm200 high-speed microwave modem b-18 tm086 – rev. 4.1 0 = mask, 1 = allow" ::= { radmm200demodnvstatus 15 } radmm200rxacquisitioncontrol object-type syntax integer { off(1), acquire(2) } max-access read-write status current description "enables acquisition and tracking." ::= { radmm200de...
Page 167
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-19 "major alarm 1 status. The agent initializes this to the value '00000000'b bit 0 = glue logic fpga status bit 1 = data fpga status bit 2 = signal lock detect bit 3 = sync lock detect bit 4 = data pll lock detect bit 5-7 = spares 0 = pa...
Page 168
Appendix b mm200 high-speed microwave modem b-20 tm086 – rev. 4.1 radmm200rxlatchedmajoralarm2status object-type syntax alarmbytetype max-access read-only status current description "a bit field. On startup, the agent initializes this to the value '00000000'b. Bit 0..7 = spares 0 = pass, 1 = fail" :...
Page 169
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-21 max-access read-only status current description "aggregate input level in dbm. Signed implied decimal point. (i.E. -265 mean -26.5dbm)" ::= { radmm200demodstatus 12 } -- -----------------------------------------------------------------...
Page 170
Appendix b mm200 high-speed microwave modem b-22 tm086 – rev. 4.1 bit 5 = fifo reload bit 6 = fifo active bit 7 = track fault 0 = mask, 1 = allow" ::= { radmm200rxchannelnvstatusentry 3 } -- -------------------------------------------------------------------------------------------------------------...
Page 171
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-23 description "minor alarm status: bit 0 = qam lock status bit 1 = fec lock status bit 2 = fifo full status bit 3 = fifo empty status bit 4 = sync lock status bit 5 = fifo reload bit 6 = fifo active bit 7 = track fault 0 = pass, 1 = fail...
Page 172
Appendix b mm200 high-speed microwave modem b-24 tm086 – rev. 4.1 radmm200rxchannelsnr object-type syntax integer (0..100) max-access read-only status current description "channel snr, signal to noise ratio." ::= { radmm200rxchannelstatusentry 9 } radmm200rxchannelcba object-type syntax integer (0.....
Page 173
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-25 radmm200rxinterfacedatainvert integer, radmm200rxinterfaceterrestrialloopback integer, radmm200rxinterfaceprbs integer, radmm200rxinterfacemajoralarmmask integer, radmm200rxinterfaceminoralarmmask integer, radmm200rxinterfacejittercont...
Page 174
Appendix b mm200 high-speed microwave modem b-26 tm086 – rev. 4.1 paralleldvb(10), parallelm2p(11), oc3(12), stm1(13), hssi(14), smpt19(15) smpt38(16) } max-access read-write status current description "selects the rx interface type." ::= { radmm200rxinterfacenvstatusentry 5 } radmm200rxinterfacesub...
Page 175
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-27 max-access read-write status current description "sets the volume on the audio channel on the ds0 interfaces" ::= { radmm200rxinterfacenvstatusentry 10 } radmm200rxinterfaceclockpolarity object-type syntax integer { normal(1), inverted...
Page 176
Appendix b mm200 high-speed microwave modem b-28 tm086 – rev. 4.1 bit 0 = interface fifo full bit 1 = interface fifo empty bit 2 = interface pll lock bit 3 = interface data activity detect bit 4 = interface clock activity detect bit 5 = interface tx input framing valid, added for aasi bit 6 = interf...
Page 177
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-29 max-access read-only status current description "index into the mm200 rx interface volatile table." ::= { radmm200rxinterfacestatusentry 1 } radmm200rxinterfacemajoralarmstatus object-type syntax alarmbytetype max-access read-only stat...
Page 178
Appendix b mm200 high-speed microwave modem b-30 tm086 – rev. 4.1 t3e3(4), t1e1(5), ds0(6), parallel(7), oc3(8), hssi(9), smpte(10) } max-access read-only status current description "interface card type." ::= { radmm200rxinterfacestatusentry 6 } -- ---------------------------------------------------...
Page 179
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-31 radmm200commonalarm1mask object-type syntax alarmbytetype max-access read-write status current description "common alarm 1 mask: bit 0 = glue logic fpga status bit 1 = test fpga status bit 2-7 = spares 0 = mask, 1 = allow" ::= { radmm2...
Page 180
Appendix b mm200 high-speed microwave modem b-32 tm086 – rev. 4.1 radmm200commonlatchedalarm1status object-type syntax alarmbytetype max-access read-only status current description "a bit field. On startup, the agent initializes this to the value '00000000'b bit 0 = glue logic fpga status bit 1 = te...
Page 181
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-33 status current description "demodulator minor alarm trap." ::= { radmm200mibtrapprefix 6 } radmm200commonalarmtrap notification-type status current description "common alarm trap." ::= { radmm200mibtrapprefix 7 } -- -------------------...
Page 182
Appendix b mm200 high-speed microwave modem b-34 tm086 – rev. 4.1 "modulator channel non-volatile status group." ::= { mm200groups 3 } mm200modchannelstatusgroup object-group objects { radmm200txchannelindex, radmm200txchannelmajoralarmstatus, radmm200txchannelminoralarmstatus, radmm200txchannellatc...
Page 183
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-35 radmm200rxminoralarm2mask } status current description "demodulator non-volatile status group." ::= { mm200groups 7 } mm200demodstatusgroup object-group objects { radmm200rxmajoralarm1status, radmm200rxmajoralarm2status, radmm200rxmino...
Page 184
Appendix b mm200 high-speed microwave modem b-36 tm086 – rev. 4.1 radmm200rxinterfacedatainvert, radmm200rxinterfaceterrestrialloopback, radmm200rxinterfaceprbs, radmm200rxinterfacemajoralarmmask, radmm200rxinterfaceminoralarmmask, radmm200rxinterfacejittercontrol, radmm200rxinterfacebytegapping } s...
Page 185
Mm200 high-speed microwave modem appendix b tm086 – rev 4.1 b-37 } status current description "modulator traps group." ::= { mm200groups 16 } mm200demodnotificationsgroup notification-group notifications { radmm200demodmajoralarmtrap, radmm200demodminoralarmtrap, radmm200commonalarmtrap } status cur...
Page 186
Appendix b mm200 high-speed microwave modem b-38 tm086 – rev. 4.1.
Page 187
Mm200 high-speed microwave modem glossary tm086 – rev. 4.1 g-1 glossary g a a ampere ac alternating current adc analog to digital converter agc automatic gain control ais alarm indication system. A signal comprised of all binary 1s. Ansi american national standards institute ascii american standard ...
Page 188
Glossary mm200 high-speed microwave modem g-2 tm086 – rev. 4.1 d dac digital to analog converter db decibels dbc decibels referred to carrier dbm decibels referred to 1.0 milliwatt dc direct current dce data communications equipment demod demodulator or demodulated dpll digital phase locked loop dte...
Page 189
Mm200 high-speed microwave modem glossary tm086 – rev. 4.1 g-3 h hssi high speed serial interface hw hardware hz hertz (unit of frequency) i ibs intelsat business services idr intermediate data rate i/o input/output ieee international electrical and electronic engineers iess intelsat earth station s...
Page 190
Glossary mm200 high-speed microwave modem g-4 tm086 – rev. 4.1 n nc normally closed no normally open ns nanoseconds nvram non-volatile random access memory n/c no connection or not connected o oqpsk offset quadrature phase shift keying p pc personal computer pll phase locked loop ppb parts per billi...
Page 191
Mm200 high-speed microwave modem glossary tm086 – rev. 4.1 g-5 t tbd to be designed or to be determined tm technical manual tpc turbo product codes tre trellis tx transmit (transmitter) txd transmit data u uart universal asynchronous receiver/transmitter uut unit under test v v volts vac volts, alte...
Page 192
Glossary mm200 high-speed microwave modem g-6 tm086 – rev. 4.1.