- DL manuals
- Radyne
- Switch
- RCS11
- Installation And Operation Manual
Radyne RCS11 Installation And Operation Manual - page 23
RCS11 1:1 Redundancy Switch
Installation
TM061 Rev. 1.3
Page 2-9
12
DTR (A) -
Input
13
Receive Ready (A) -
Output
14
NC
17
Terminal Timing (A) -
Input
19
Signal GND
GND
20
Common
GND
21
External FIFO Buffer Output
Clock (B) +
Input
22
Transmit Data (B) +
Input
23
Transmit Clock (B) +
Output
24
Receive Data (B) +
Output
25
RTS (B) +
Input
26
Receive Clock (B) +
Output
27
CTS (B) +
Output
29
Data Mode (B) +
Output
30
DTR (B) +
Input
31
Receive Ready (B) +
Output
33
NC
35
Terminal Timing (B) +
Input
Table 2-6. J7 (Modem A) /J11 (Modem B) RS422 Data Interface
Modem A and Modem B Connector Pin Assignment
Pin #
Signal Name
Direction
1
Shield
3
External FIFO Buffer Output
Clock (A) -
Output
4
Transmit Data (A) -
Output
5
Transmit Clock (A) -
Input
6
Receive Data (A) -
Input
7
RTS (A) -
Output
8
Receive Clock (A) -
Input
9
CTS (A) -
Input
11
Data Mode (A) -
Input
12
DTR (A) -
Output
13
Receive Ready (A) -
Input
14
Mod Fault Alarm
OC TTL Input
Summary of RCS11
Page 1
Rcs11 1:1 redundancy switch installation and operation manual tm061 rev. 1.3 march, 1998 - notice - 1998, radyne corporation. All rights reserved. Unauthorized reproduction of this manual in any form without the expressed written approval of radyne corporation is strictly prohibited. This manual may...
Page 3
Rcs11 1:1 redundancy switch warranty policy tm061 rev. 1.3 ii radyne warranty policy warranty and service radyne (seller) warrants the items manufactured and sold by radyne to be free of defects in material and workmanship for a period of two (2) years from date of shipment radyne's obligation under...
Page 4
Warranty policy rsc11 1:1 redundancy switch tm061 rev. 1.3 iii statements made by any person, including representatives of radyne, which are inconsistent or in conflict with the terms of this warranty, shall not be binding upon radyne unless reduced to writing and approved by an officer of radyne. W...
Page 6: Rcs11 1:1 Redundancy Switch
Rcs11 1:1 redundancy switch record of revisions tm061 rev. 1.3 iv rcs11 1:1 redundancy switch installation and operation manual tm061 - record of revisions radyne corporation is constantly improving its products and therefore the information in this document is subject to change without prior notice...
Page 7
Rcs11 1:1 redundancy switch table of contents tm061 rev. 1.3 v table of contents 1.0 introduction………………….……………………………………………………………………………….. 1- 1 1.1 manual format…………………..…………………………………………………………………………… 1- 1 1.2 cautions and warnings.…………………………………..………………………………………………… 1- 1 2.0 installation requirements....
Page 8
Rcs11 1:1 redundancy switch table of contents tm061 rev. 1.3 vi 2.8 rcs11/dmd2400 sync v.35 interface rear panel connectors……………………………………… 2- 14 2.9 rcs11/dvb3000 radyne parallel interface rear panel connections……………………………… 2- 17 2.10 rcs11 radyne parallel interface rear panel connections……………………………...
Page 9
Dmd2400 scpc satellite modem table of contents tm050 - rev. 2 vii 5.1.2 front panel board…………………………..…………………………………………………………..…… 5-1 5.1.3 redundant power supplies.………..…………………………………..………………………………….. 5-1 5.2 rcs11 general operation.……..……………………………………………….…………………………. 5-1 5.2.1 signals………………………………..………...
Page 11
Rcs11 1:1 redundancy switch description tm061 rev. 1.3 page 1-1 section 1 - rcs11 1:1 redundancy switch description 1.0 description the radyne rcs11 1:1 redundancy switch provides simple backup redundancy protection for all configurations of dmd15 and dmd2400 satellite modems as well as the dvb3000 ...
Page 12
Description rcs11 1:1 redundancy switch page 1-2 tm061 rev. 1.3 1.4 cautions and warnings caution: a caution identifies and also defines a procedure which must be followed precisely in order to ensure the proper use of the equipment. Warning: a warning identifies and also defines a procedure which r...
Page 13
Rcs11 1:1 redundancy switch description tm061 rev. 1.3 page 1-3.
Page 15
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-1 section 2 - installation 2.0 installation requirements this chapter instructs the user in the methods for setting up and installing an rcs11 1:1 redundancy switch into a satellite modem system. The cabling configurations for two dmd240...
Page 16
Installation rcs11 1:1 redundancy switch page 2-2 tm061 rev. 1.3 grounding is achieved automatically when the three prong power plug is inserted into a power receptacle. This should be checked by testing that there is no voltage present between the chassis of the switch and the power line ground. **...
Page 17
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-3.
Page 18
Installation rcs11 1:1 redundancy switch page 2-4 tm061 rev. 1.3.
Page 19
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-5.
Page 20
Installation rcs11 1:1 redundancy switch page 2-6 tm061 rev. 1.3.
Page 21
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-7 2.5 rcs11 rear panel connectors and pinouts all modem connections are made to the labeled connectors located on the rear of the rcs11. The connector definitions and pinouts below are those on the rcs11 unit. Any connection interfacing ...
Page 22
Installation rcs11 1:1 redundancy switch page 2-8 tm061 rev. 1.3 5 ground gnd 6 rx_a (-) input 7 rx_b (-) input 8 tx_a (-) output 9 tx_b (-) output 2.6 rcs11/dmd2400 sync/rs422 satellite modem rear panel connectors table 2-4. Rcs11 rear panel connectors (dmd2400 sync rs422 interface configuration) c...
Page 23
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-9 12 dtr (a) - input 13 receive ready (a) - output 14 nc 17 terminal timing (a) - input 19 signal gnd gnd 20 common gnd 21 external fifo buffer output clock (b) + input 22 transmit data (b) + input 23 transmit clock (b) + output 24 recei...
Page 24
Installation rcs11 1:1 redundancy switch page 2-10 tm061 rev. 1.3 17 terminal timing (a) - output 19 signal gnd gnd 20 common gnd 21 external fifo buffer output clock (b) + output 22 transmit data (b) + output 23 transmit clock (b) + input 24 receive data (b) + input 25 rts (b) + output 26 receive c...
Page 25
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-11 7 rts request to send (pin 7 & 8 tied together) 3 txd-a transmit data a 8 cts clear to send 4 txd-b transmit data b 9 nc no connection 5 ground signal ground 2.7 rcs11/dmd2400 sync rs232 interface rear panel connectors table 2-9. Rcs1...
Page 26
Installation rcs11 1:1 redundancy switch page 2-12 tm061 rev. 1.3 24 tt a (-) output no connection nc 9, 10, 11, 12, 13, 14, 16, 18, 21, 22, table 2-11. J7/j11 modem ‘a’ / modem ‘b’ rs232 data interface 25-pin ‘d-sub’ female connector pin assignment pin # name direction 1,7 shield/signal common gnd ...
Page 27
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-13 9 nc no connection 5 ground signal ground table 2-13. J18 es ‘a’ and j19 es ‘b’ channel connection 9-pin female ‘d’ connector pin # signal name description 1 rxd-b receive data b 6 dsr date set ready 2 rxd-a receive data a 7 rts reque...
Page 28
Installation rcs11 1:1 redundancy switch page 2-14 tm061 rev. 1.3 1 chassis gnd 7 sig gnd gnd 15 sct a (st) output 12 sct b (st) output 2 sd a (sd) input 14 sd b (sd) input 24 scte a (tt) input 11 scte b (tt) input 17 scr a (rt) output 9 scr b (rt) output 3 rd a (rd) output 16 rd b (rd) output 4 rts...
Page 29
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-15 16 rd b (rd) input 4 rts output 5 cts input 6 dsr input 8 cd input 25 mod fault alarm oc ttl input 23 demod fault alarm oc ttl input 21 ext fifo clock b (+) output 19 ext fifo clock a (-) output 20 dtr output table 2-17. Terrestrial e...
Page 30
Installation rcs11 1:1 redundancy switch page 2-16 tm061 rev. 1.3 4 txd-b transmit data b 9 nc no connection 5 ground signal ground 2.9 rcs11/dvb3000 radyne serial interface rear panel connections table 2-19. Rcs11 rear panel connectors (dvb3000/rs-449/rs-422 serial interface configuration) connecto...
Page 31
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-17 25 ready to send (rts) b input 26 receive timing (rt) b output 27 clear to send (cts) b output 29 data mode (dm) b output 33 ext ref int b input 35 serial clock transmit external (scte) b input 37 common gnd table 2–21. J7/j11 - mod ‘...
Page 32
Installation rcs11 1:1 redundancy switch page 2-18 tm061 rev. 1.3 2.10 rcs11 radyne parallel interface rear panel connections table 2-22. Rcs11 rear panel connectors (radyne rs422 parallel interface configuration) connector id nomenclature description j7 data a rs422 parallel 25-pin ‘d’ data connect...
Page 33
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-19 7 d2+ input 20 d2- input 8 d3+ input 21 d3- input 9 d4+ input 22 d4- input 10 d5+ input 23 d5- input 11 d6+ input 24 d6- input 12 d7+ input 25 d7- input 13 not connected --------------- table 2-24. J7/j11 - mod ‘a’/mod ‘b’ radyne rs-4...
Page 34
Installation rcs11 1:1 redundancy switch page 2-20 tm061 rev. 1.3 10 d5+ output 23 d5- output 11 d6+ output 24 d6- output 12 d7+ output 25 d7- output 13 not connected --------------- table 2-25. J18 fault ‘a’ and j19 fault ‘b’ connection 9-pin female ‘d’ connector pin # signal name direction 6 mod f...
Page 35
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-21 3 d7 + input 4 d6 + input 5 d5 + input 6 d4 + input 7 d3 + input 8 d2 + input 9 d1 + input 10 d0 + input 11 dvalid + input 12 psync + input 13 cable shield input 14 clock - input 15 system gnd ground 16 d7 - input 17 d6 - input 18 d5 ...
Page 36
Installation rcs11 1:1 redundancy switch page 2-22 tm061 rev. 1.3 9 d1 + output 10 d0 + output 11 dvalid + output 12 psync + output 13 cable shield output 14 clock - output 15 system gnd ground 16 d7 - output 17 d6 - output 18 d5 - output 19 d4 - output 20 d3 - output 21 d2 - output 22 d1 - output 2...
Page 37
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-23 2.11 rcs11/dmd15 universal interface module (uim) connectors the following tables contain the pinouts, signals, descriptions and directions for the connectors located on the rcsd11 to dmd15 uim. J23 - sd - send data j23 is the unbalan...
Page 38
Installation rcs11 1:1 redundancy switch page 2-24 tm061 rev. 1.3 27 cs-b clear to send b (+) output 11 dm-a data mode a (-) output 29 dm-b data mode b (+) output 13 rr-a receiver ready a (-) output 31 rr-b receiver ready b (+) output 15 bal exc- a external clock a (-) input 33 bal exc- b external c...
Page 39
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-25 j7/j11 - switch connector table 2-33. J7/j11 - switch connector - 68-pin high-density female pin no. Signal description directio n 1 g.703b sd-a g.703 send data input a input 2 sync sd-a synchronous data send data input -a input 3 esc...
Page 40
Installation rcs11 1:1 redundancy switch page 2-26 tm061 rev. 1.3 23 es dsr ibs es data set ready (rs232 only) output 24 esctxc-a idr esc transmit 8 kbps output clock output 25 esctxd-a idr esc transmit 8 kbps output data input 26 escrxc-a idr esc receive 8 kbps output clock output 27 escrxd-a idr e...
Page 41
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-27 55 dmd flt demod fault open collector output output open collector 56 es rxd-b ibs es receive data input - b output 57 gnd ground 58 esctxc-b idr esc transmit 8 kbps output clock b output 59 esctxd-b idr esc transmit 8 kbps output dat...
Page 42
Installation rcs11 1:1 redundancy switch page 2-28 tm061 rev. 1.3 13 nc 14 escbwo 1c backward alarm out-1 c 15 escbwo 1nc backward alarm out-1 nc 16 escbwo 2c backward alarm out- 2 c 17 escbwo 2nc backward alarm out- 2 nc 18 escbwo 3c backward alarm out- 3 c 19 escbwo 3nc backward alarm out- 3 nc 20...
Page 43
Rcs11 1:1 redundancy switch installation tm061 rev. 1.3 page 2-29 14 esctxc-b tx clock-b output 15 esctxo-b tx octet-b output j16 - esc audio table 2-36. J16 - esc audio - 9-pin female ‘d’ pin no. Signal description direction 1 escaudtx 1a tx audio 1a input 2 escaudrx 1a rx audio 1a output 3 gnd 4 e...
Page 44
Installation rcs11 1:1 redundancy switch page 2-30 tm061 rev. 1.3 interconnecting the modems and the rcs11. 2. Interconnect the units as shown in figure 2-3, 2-4 or 2-5 depending upon the equipment type being configured. 3. Attach the ac line cords to the modems and the rcs11. 4. Using the on/off sw...
Page 45
Rcs11 1:1 redundancy switch operation tm061 rev. 1.3 page 3-1 section 3 - operation 3.1 operating procedures the rcs11 is designed to require minimal operator intervention and control during normal operation. After initial setup, the unit should operate in a relatively ‘transparent’ manner, providin...
Page 46
Operation rcs11 1:1 redundancy switch page 3-2 tm061 rev. 1.3 table 3-1. Rcs11 front panel controls and indicators nomenclature description function power 1 indicates ps1 has power applied led illuminates green for power available power 2 indicates ps2 has power applied led illuminates green for pow...
Page 47
Rcs11 1:1 redundancy switch operation tm061 rev. 1.3 page 3-3.
Page 49
Rcs11 1:1 redundancy switch maintenance tm061 rev. 1.3 page 4-1 section 4 - basic troubleshooting and maintenance 4.1 basic troubleshooting and maintenance this chapter provides information on the basic troubleshooting and repair procedures for the rcs11 1:1 switch that may be performed on-site by q...
Page 50
Maintenance rcs11 1:1 redundancy switch 4-2 tm061 rev. 1.3 a read-only memory (rom) failure in the switch; a random access memory (ram) failure in the switch; a loss of carrier detect on a demodulator channel where this attribute is monitored; a loss of terrestrial input clock on a channel where thi...
Page 51
Rcs11 1:1 redundancy switch principles of operation tm061 rev. 1.3 page 5-1 section 5 - principles of operation 5.0 principles of operation this chapter provides additional basic information on the rcs11. 5.1 rcs11 major assemblies the rcs11 redundancy control unit contains the modules that control ...
Page 52
Principles of operation rcs11 1:1 redundancy switch page 5-2 tm061 rev. 1.3 5.2.2 fail-safe if the rcs11 has a non-recoverable internal fault, the mod and demod both revert back to modem a, the switch fault led is illuminated, and the switch fault relay switches to a faulted state. If power supply 1...
Page 53
Rcs11 1:1 redundancy switch technical specifications tm061 rev. 1.3 a-1 appendix a rcs11 1:1 redundancy switch technical specifications a.1 introduction this section defines the technical performance parameters for the rcs11 1:1 redundancy switch..
Page 54
Rcs11 1:1 redundancy switch technical specifications tm061 rev. 1.3 a-2 rcs11 1:1 redundancy switch technical specifications general specifications online modulators: 1 unit online demodulators: 1 unit backup modulators: 1 unit backup demodulators: 1 unit uplink transponders: 1 unit downlink transpo...
Page 55
Rcs11 1:1 redundancy switch technical specifications tm061 rev. 1.3 a-3 power and environmental prime power: 100/240 vac, 50-60 hz, 40 watts (one bank) operating temp: 0 to 50 degrees c, 95% humidity, non-condensing storage temp: -20 to 70 degrees c, 99% humidity, non-condensing physical size: 19 w ...
Page 56
Appendix c – rcs11 dip switch configuration tables.
Page 57
Rcs11 configuration how to use this table all reserved switches should be left in the off position. Select 'soft' setting to allow changes in terminal mode. Select for any setting that doesn't seem to apply. Config s2-2 s2-1 s2-8 .. S2-3 are reserved for future expansion and should be left in the of...
Page 58
41 off off on off off on 42 off off on off on off 43 off off on off on on 44 off off on on off off 45 off off on on off on 46 off off on on on off 47 off off on on on on 48 off on off off off off 49 off on off off off on 50 off on off off on off 51 off on off off on on 52 off on off on off off 53 of...
Page 59
77 on off on on off on 78 on off on on on off 79 on off on on on on 80 on on off off off off 81 on on off off off on 82 on on off off on off 83 on on off off on on 84 on on off on off off 85 on on off on off on 86 on on off on on off 87 on on off on on on 88 on on on off off off 89 on on on off off ...
Page 60
4.