Fa-200 alarm bar user’s guide rev. A october 2009 p/n f05-4030-000
© copyright 2009 rae systems by honeywell.
Fa-200 alarm bar user’s guide 1 contents warnings ............................................................................. 3 1 standard contents .............................................................. 4 2 general information .......................................................... 4 2....
Fa-200 alarm bar user’s guide 2 read before operating this manual must be carefully read by all individuals who have or will have the responsibility of using, maintaining, or servicing this product. The product will perform as designed only if it is used, maintained, and serviced in accordance with ...
Fa-200 alarm bar user’s guide 3 warnings use only in non-hazardous locations. For safety reasons, this equipment must be operated and serviced by qualified personnel only. Read and understand instruction manual completely before operating or servicing. Avertissement utiliser uniquement en zone non-d...
Fa-200 alarm bar user’s guide 4 1 standard contents • fa-200 alarm bar • integral 10-meter (33-foot) connection cable • user’s guide 2 general information the fa-200 alarm bar works with rae systems fmc2000 controller and other compatible devices. It provides bright visible and loud audible notifica...
Fa-200 alarm bar user’s guide 5 3 physical description the fa-200 alarm bar comes pre-assembled and requires only connection via its integrated cord to a controller with relays. It has mounting flanges at the top and bottom with four holes that accept screws for attaching the fa-200 alarm bar to a w...
Fa-200 alarm bar user’s guide 6 4. Hold the fa-200 alarm bar firmly against the wall and insert and tighten the screws. The fa-200 alarm bar is now ready to be connected to the controller. 4.2 drilling chart when mounting the fmc2000 on a wall, make sure to use heavy-duty steel screws spaced as indi...
Fa-200 alarm bar user’s guide 7 4.4 connecting to an fmc2000 controller the fmc2000 has a female 6-pin connector on the bottom that is designed for connection with a rae systems fa-200 alarm bar. Note: the internal wires from the fmc2000 connector are pre- wired to the no (normally open) connection ...
Fa-200 alarm bar user’s guide 8 4.5 positioning the siren horn if the fa-200 alarm bar is to be used outdoors or in other environments where it may become wet, point the horn slightly downward to allow drainage. This will prolong its life and ensure its effectiveness. 5 maintenance no periodic maint...
Fa-200 alarm bar user’s guide 9 6 specifications size 8" x 33" x 4.5" (20.3 cm x 84 cm x 11.5 cm), including siren horn weight 14.5 lbs (6.6 kg), excluding cable enclosure material stainless steel with stainless steel protection bars over each strobe light audible alarm 112db @ 3 m ( 10′) visual ala...
Fa-200 alarm bar user’s guide 10 special servicing note if the instrument needs to be serviced, contact either: the rae systems distributor from whom the instrument was purchased; they will return the instrument on your behalf. Or the rae systems technical service department. Before returning the in...
Fa-200 alarm bar user’s guide 11 7 troubleshooting problem possible reasons & solutions siren inoperative reasons: wiring problem. Alarm level set too low at controller. Solutions: make sure cable is connected to controller. Make sure cable is not damaged. Check siren horn for obstruction. Test rela...
Fa-200 alarm bar user’s guide 12 7.1 checking fmc2000 relay continuity each relay in an fmc2000 controller has a common terminal and a normally open (no) and normally closed (nc) terminal. If you think the wiring to the fa-200 alarm bar is correct and that the fa-200 alarm bar is in working order, b...
Fa-200 alarm bar user’s guide 13 3. In the relay diagnostic menu, toggle the relay by pressing the keypad’s corresponding key (1, 2, 3, 4. 5). 4. Touch the probes to the nc and com terminals on the relay block. 5. Again, toggle the relay by pressing the corresponding key on the keypad. Each time you...
Fa-200 alarm bar user’s guide 14 note: make sure the jumpers (marked jp for each of the five relays) are in place on the printed circuit board that includes the five alarm relay connection blocks in the fmc2000. If any of the jumpers is missing, the relay is in “dry contact” configuration, and no vo...
Fa-200 alarm bar user’s guide 15 8 technical support to contact rae systems technical support team: monday through friday, 7:00am to 5:00pm pacific (us) time phone (toll-free): +1 888-723-4800 phone: +1 408-952-8461 email: tech@raesystems.Com.
Fa-200 alarm bar user’s guide 16 9 rae systems contacts rae systems by honeywell world headquarters 3775 n. First st. San jose, ca 95134-1708 usa phone: +1 408.952.8200 fax: +1 408.952.8480 e-mail: customerserv@raesystems.Com web site: www.Raesystems.Com rae systems technical support monday through ...
Fa-200 alarm bar user’s guide 17 rae systems uk ltd d5 culham innovation centre culham science centre abingdon, oxon ox14 3db united kingdom phone: +44 1865408368 fax: +44 1235531119 mobile: +44 7841362693 email: raeuk@raeeurope.Com rae systems france 336, rue de la fée des eaux 69390 vernaison fran...
Fa-200 alarm bar user’s guide 18 rae systems spain, s.L. Av. Remolar, 31 08820 el prat de llobregat spain phone: +34 933 788 352 fax: +34 933 788 353 mobile: +34 687 491 106 email: spainsales@raesystems.Com web: www.Raespain.Com rae systems middle east lob 7, ground floor, office 19 jebel ali free z...
Fa-200 alarm bar user’s guide 19 rae systems korea 101-1301, bucheon technopark iii, samjungdong 36-1, oh jung-gu, bucheon-si, gyeong gi-do korea 421-741 phone: +82.32.624.0460 fax: +82.32.624.0463 email: krsales@raesystems.Com.
Rae systems by honeywell world headquarters 3775 n. First st. San jose, ca 95134-1708 usa phone: 408.952.8200 fax: 408.952.8480 e-mail: customerserv@raesystems.Com web site: www.Raesystems.Com rev. A october 2009 p/n f05-4030-000
