1. DL manuals
  2. RAM
  3. Trucks
  4. 1500 2018
  5. Owner's Manual

RAM 1500 2018 Owner's Manual

Other manuals for 1500 2018: Service Supplement Manual

Summary of 1500 2018

  • Page 1

    Second edition printed in the u.S.A. ©2017 fca us llc. All rights reserved. Ram is a registered trademark of fca us llc. 18ds-126-ab o w n e r ’ s m a n u a l 2 0 1 8 1 5 0 0 / 2 5 0 0 / 3 5 0 0 r a m t r u c k stick with the specialists ® ram truck 1500/2500/3500 2018.

  • Page 2

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 graphical table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . . .5 ▫ essential information . . . . . . . . . . . . . . . . . . . . . .5 ▫ symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 䡵 warnings and...

  • Page 6

    Introduction dear customer, congratulations on selecting your new vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality. This is a specialized utility vehicle. It can go places and perform tasks that conventional passenger vehicles are not intended. It...

  • Page 7

    Described for technical and/or commercial reasons. For further information, contact an authorized dealer. If applicable, refer to the owners manual supplement for related information. Note: after reviewing the owner’s information, it should be stored in the vehicle for convenient referencing, and re...

  • Page 8

    Symbols consult the following table for a description of the symbols that may be used on your vehicle or throughout this owner’s manual: 6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may mi...

  • Page 11: Contents

    Graphical table of contents contents 䡵 front view . . . . . . . . . . . . . . . . . . . . . . . . . . .10 䡵 rear view. . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 䡵 instrument panel . . . . . . . . . . . . . . . . . . . . .12 䡵 interior . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 12

    Front view front view 1 — hood/engine compartment 4 — wheels/tires 2 — windshield 5 — doors 3 — headlights 6 — exterior mirrors 10 graphical table of contents.

  • Page 13

    Rear view rear view 1 — rear lights 2 — tailgate 2 graphical table of contents 11.

  • Page 14

    Instrument panel instrument panel 1 — air vents 4 — instrument cluster 2 — multifunction lever 5 — gear selector 3 — steering wheel 6 — radio 12 graphical table of contents.

  • Page 15

    Interior interior 1 — door locks/window switches 4 — radio controls 2 — seats 5 — storage compartment 3 — gear selector 2 graphical table of contents 13.

  • Page 17: Contents

    Getting to know your vehicle contents 䡵 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 ▫ key fobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 䡵 ignition switch . . . . . . . . . . . . . . . . . . . . . . .27 ▫ wireless ignition node (win) — if equipped. . . ...

  • Page 18

    ▫ automatic door locks — if equipped . . . . . . . .42 ▫ child-protection door lock . . . . . . . . . . . . . . . .43 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 ▫ manual front seat adjustment . . . . . . . . . . . . . .44 ▫ manual rear seat adjustment . . . . . . . . ....

  • Page 19

    ▫ tilt side mirrors in reverse — if equipped . . . . .71 ▫ illuminated vanity mirror — if equipped . . . . . .72 䡵 exterior lights . . . . . . . . . . . . . . . . . . . . . . .73 ▫ headlight switch . . . . . . . . . . . . . . . . . . . . . . .73 ▫ headlights . . . . . . . . . . . . . . . . . . . . ....

  • Page 20

    ▫ operating tips . . . . . . . . . . . . . . . . . . . . . . . .104 䡵 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 ▫ power windows — if equipped . . . . . . . . . . . .107 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . . .109 䡵 power sunroof — if equipped . . . . ...

  • Page 21

    ▫ auxiliary switches — if equipped . . . . . . . . . .138 䡵 pickup box . . . . . . . . . . . . . . . . . . . . . . . . . . .139 ▫ cargo camera — if equipped . . . . . . . . . . . . .140 䡵 rambox — if equipped . . . . . . . . . . . . . . . . .141 ▫ rambox integrated box side storage bins. . . . . .14...

  • Page 22

    Keys key fobs your vehicle uses either a wireless ignition node system or keyless ignition system. The ignition system consists of a key fob with a remote keyless entry (rke) and an ignition switch. The keyless ignition system consists of a key fob and keyless enter-n-go button. Note: the key fob ma...

  • Page 23

    The fourth position is start, during start run will illuminate. It also contains the key fob and an emergency key, which stores in the rear of the key fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the key fob go dead. You can keep the emergency key wit...

  • Page 24

    Note: inserting the key fob with integrated key into the ignition switch disables the system from responding to any button pushes from that key fob. Driving at speeds 5 mph (8 km/h) and above disables the system from responding to all key fob buttons for all key fobs. To unlock the doors and tailgat...

  • Page 25

    To lock the doors and tailgate push and release the lock button on the key fob to lock all doors, the tailgate and the rambox (if equipped). The turn signal lights will flash and the horn will chirp to acknowl- edge the signal. Sound horn with remote key lock this feature will cause the horn to chir...

  • Page 26

    Air suspension (remote lowering of the vehicle) — if equipped for easy entry and loading, your vehicle can be lowered by pushing the key fob air suspension lowering button two times. When key fob low- ering is requested, the vehicle will send a series of chirps and flashes to alert the customer that...

  • Page 27

    1. Remove the emergency key by sliding the mechanical latch on the back of the key fob sideways with your thumb and then pull the key out with your other hand. Emergency win key removal emergency key removal 3 getting to know your vehicle 25.

  • Page 28

    2. Separating key fob halves requires screw removal – if equipped, and gently prying the two halves of the key fob apart. Make sure not to damage the seal during removal. Remove screw from key fob case separating win key fob case 26 getting to know your vehicle.

  • Page 29

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the b...

  • Page 30

    Detents and one that is spring-loaded. The detent positions are off, acc, and on/run. The start position is a spring-loaded momentary contact position. When released from the start position, the switch automatically returns to the on/run position. Removing key fob from the (win) ignition place the g...

  • Page 31

    Warning! (continued) into reverse, apply the parking brake, turn the vehicle off, remove the key fobs from the vehicle, and lock all doors. If equipped with keyless enter- n-go, always make sure the keyless ignition node is in the off mode, remove the key fob from the vehicle and lock the vehicle. •...

  • Page 32

    Keyless push button ignition — if equipped this feature allows the driver to operate the ignition switch with the push of a button as long as the remote keyless entry key fob is in the passenger compartment. The keyless push button ignition has four operating positions; three of which are labeled an...

  • Page 33

    Note: • ⬙keyed⬙ ignition systems will chime in off or acc when the driver door is open. • “keyless⬙ ignition systems will chime in acc or run when the driver door is open. • the instrument cluster display will display “key in ignition.” remote start — if equipped how to use remote start all of the f...

  • Page 34

    • remote start disabled — start vehicle to reset the instrument cluster display message stays active until the ignition is turned to the on/run position. To enter remote start mode push and release the remote start button on the key fob twice within five seconds. The parking lights will flash, vehic...

  • Page 35

    Activated. These features will stay on through the duration of remote start or until the ignition switch is placed in the on/run mode. Note: the remote start comfort system can be activated and deactivated through the uconnect system. Refer to “uconnect settings” in “multimedia” for further informa-...

  • Page 36

    An invalid key fob to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds. If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electro...

  • Page 37

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 38

    Exterior zone (refer to ⬙keyless enter- n-go — passive entry ⬙ in ⬙getting to know your vehicle⬙ for further information). • push the lock button on the key fob. 3. If any doors are open, close them. The vehicle security alarm will set when you use the power door locks, or use the key fob to lock th...

  • Page 39

    Rearming of the system the vehicle security alarm will rearm itself after the 15 additional minutes of headlights and vehicle security light flashing, if the system has not been disabled. If the condi- tion which initiated the alarm is still present, the system will ignore that condition and monitor...

  • Page 40

    Warning! (continued) • for personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • before exiting a vehicle, always shift the automatic transmission into park or the manual transmission into first gear or revers...

  • Page 41

    If you push the power door lock switch while the key fob is in the ignition, and any front door is open, the power locks will not operate. This prevents you from accidentally locking your key fob in the vehicle. Removing the key fob or closing the door will allow the locks to operate. A chime will s...

  • Page 42

    To unlock from the driver’s side: with a valid passive entry key fob within 5 ft (1.5 m) of the driver door handle, grab the front driver door handle to unlock the driver’s door automatically. The interior door panel lock knob will raise when the door is unlocked. Note: if “unlock all doors 1st pres...

  • Page 43

    Automatically unlocks all vehicle doors and chirps the horn three times (on the third attempt all doors will lock and the passive entry key fob can be locked in the vehicle). To lock the vehicle’s doors: with one of the vehicle’s passive entry key fobs within 5 ft (1.5 m) of the driver or passenger ...

  • Page 44

    The vehicle doors can also be locked by using the key fob lock button or the lock button located on the vehicle’s interior door panel. General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the...

  • Page 45

    Child-protection door lock to provide a safer environment for children riding in the rear seat, the rear doors (if equipped) of your vehicle have the child-protection door lock system. To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to enga...

  • Page 46

    Note: • after setting the child-protection door lock system, always test the door from the inside to make certain it is in the desired position. • for emergency exit with the system engaged, move the door lock switch to the unlock position, roll down the window and open the door with the outside doo...

  • Page 47

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 48

    Warning! (continued) • to avoid injury, place your hand on the seatback and actuate the handle, then position the seatback in the desired position. 40-20-40 front bench seat — if equipped the seat is divided into three segments. The outboard seat portions are each 40% of the total width of the seat....

  • Page 49

    Outboard side of the driver’s seat cushion. There are two power seat switches that are used to control the movement of the seat cushion and the seatback. Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward. The seat will...

  • Page 50

    Warning! (continued) • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a col...

  • Page 51

    Adjusting the seat up or down the height of the seats can be adjusted up or down. Pull upward or push downward on the rear of seat switch, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Tilting the seat up or down the angle of the se...

  • Page 52

    3. Push and release the set (s) button on the memory switch. 4. Within five seconds, push and release either of the memory buttons (1) or (2). The instrument cluster dis- play will show which memory position has been set. Note: • memory profiles can be set without the vehicle in park, but the vehicl...

  • Page 53

    Memory position recall note: • for vehicles equipped with an automatic transmission, the vehicle speed must be lower than 5 mph to recall memory positions. If a recall is attempted when the vehicle speed is greater than 5 mph, a message will be displayed in the instrument cluster display. • for vehi...

  • Page 54

    Keyless enter-n-go), the driver’s seat will move about 2.4 inches (60 mm) rearward if the driver’s seat position is greater than or equal to 2.7 inches (67.7 mm) forward of the rear stop. The seat will return to its previously set position when you place the ignition into the acc or run position. • ...

  • Page 55

    Front heated seats the front heated seats control buttons are located on the center instrument panel below the climate controls. If your vehicle is equipped with a touchscreen, the front heated seats control buttons are also located within the climate or controls screen of the touchscreen. • press t...

  • Page 56

    There are two heated seat switches that allow the rear passengers to operate the seats independently. You can choose from hi, lo or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for hi, one for lo and none for off. Pu...

  • Page 57

    Vehicles equipped with remote start on models that are equipped with remote start, the venti- lated seats can be programmed to come on during a remote start. If your vehicle is equipped with a touchscreen, this feature can be programmed through the uconnect system. Refer to “uconnect settings” in “m...

  • Page 58

    2. Fold the seat back forward. Note: you may experience deformation in the seat cush- ion from the seat belt buckles if the seats are left folded for an extended period of time. This is normal and by simply opening the seats to the open position, over time the seat cushion will return to its normal ...

  • Page 59

    To fold either rear seat flat: 1. Lift the handle, located on the outboard side of either of the rear seats. 2. Fold the seatback down and push the seat forward. 3. Lift the seat back, to return the seat to the upright position. Be sure the seat is locked in place. Note: you may experience deformati...

  • Page 60

    Warning! An improperly latched seat could cause serious injury or death. Make sure that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. Plastic grocery bag retainers ...

  • Page 61

    Note: do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head. Rear head restraint adjustment the rear seats are equipped with adjustable and removable head restraints. To raise the head restraint, pull upward on t...

  • Page 62

    • do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clear- ance to the back of the head. Front head restraint removal to remove the head restraint, raise it up as far as it can go. Then, push the adjustment button and the release button at th...

  • Page 63

    Steering wheel tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the multifunction lever. Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wh...

  • Page 64

    • press the heated steering wheel button a second time to turn the heating element off. Note: the engine must be running for the heated steering wheel to operate. Vehicles equipped with remote start on models that are equipped with remote start, the heated steering wheel can be programmed to come on...

  • Page 65

    • the pedals can be adjusted with the ignition off. • the pedals cannot be adjusted when the vehicle is in reverse or when the speed control system is on. The following messages will appear on vehicles equipped with an instrument cluster display if the pedals are attempted to be adjusted when the sy...

  • Page 66

    Caution! Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjust- able pedal’s path. Mirrors inside day/night mirror — if equipped the mirr...

  • Page 67

    The automatic dimming feature can be turned on or off through the touchscreen. • press the mirror dimmer button once to turn the feature on. • press the mirror dimmer button a second time to turn the feature off. Caution! To avoid damage to the mirror during cleaning, never spray any cleaning soluti...

  • Page 68

    When the vehicle is placed into reverse gear, a video display illuminates to display the image generated by the rear view camera located on the tailgate handle. The auto dimming feature is also disabled to improve rear view viewing. Outside mirrors to receive maximum benefit, adjust the outside mirr...

  • Page 69

    Power mirrors — if equipped the controls for the power mirrors are located on the driver’s door trim panel. The power mirror controls consist of mirror select buttons and a four-way mirror control switch. Power mirror controls location power mirror controls 1 — mirror select buttons 2 — four-way mir...

  • Page 70

    To adjust a mirror, push either the l (left) or r (right) button to select the mirror that you want to adjust. Using the mirror control switch, push on any of the four arrows for the direction that you want the mirror to move. Power folding outside mirrors for standard and trailer tow — if equipped ...

  • Page 71

    Resetting the power folding outside mirrors you may need to reset the power folding mirrors if the following occurs: • the mirrors are accidentally blocked while folding. • the mirrors are accidentally manually folded/unfolded. • the mirrors come out of the unfolded position. • the mirrors shake and...

  • Page 72

    Outside mirrors folding feature all outside mirrors are designed to be able to be manually folded both forward and rearward to prevent damage. Caution! It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location. Trailer towing...

  • Page 73

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature will be activated whenever you turn on the rear window defroster (if equipped). Refer to “climate controls” in this section for further information. Tilt side mirrors in reverse — if equipped tilt side mirrors i...

  • Page 74

    Illuminated vanity mirror — if equipped illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the light. “slide-on-rod” features of sun visor ...

  • Page 75

    Exterior lights headlight switch the headlight switch is located on the left side of the instrument panel, next to the steering wheel. The headlight switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped). Your vehicle is eq...

  • Page 76

    Headlights to turn on the headlights, rotate the headlight switch clockwise to the headlight position. When the headlight switch is on, the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to ...

  • Page 77

    Automatic high beam headlamp control — if equipped the automatic high beam headlamp control system provides increased forward lighting at night by automat- ing high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera de- tects vehicle specific light an...

  • Page 78

    3. Push the multifunction lever away from you (toward front of vehicle) to engage the high beam mode. Note: this system will not activate until the vehicle is at or above 20 mph (32 km/h). To deactivate 1. Pull the multifunction lever toward you (or rearward in vehicle) to manually deactivate the sy...

  • Page 79

    Parking lights and panel lights to turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the o (off) position. Headlights on with wipers (available with automatic headlights only) when this f...

  • Page 80

    Fog lights — if equipped the fog lights are turned on by rotating the headlight switch to the parking light or headlight position and pushing in the headlight rotary control. The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator ...

  • Page 81

    Lane change assist — if equipped tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Cargo light with bed lights — if equipped the cargo light and bed lights (if equipped) are turned on by pushing th...

  • Page 82

    The cargo light and bed lights (if equipped) will turn on for approximately 60 seconds when a key fob unlock button is pushed, as part of the illuminated entry feature. Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. I...

  • Page 83

    Fob, if equipped. These lights are also operated individu- ally as reading lights by pushing on the corresponding lens. Note: the courtesy/reading lights will remain on until the switch is pushed a second time, so be sure they have been turned off before exitingthe vehicle. If the interior lights ar...

  • Page 84

    Ambient light the overhead console is equipped with an ambient light feature. This light casts illumination for improved visibility of the floor console area. Dimmer control the brightness of the instrument panel as well as the ambient lighting can be regulated by rotating the dimmer control to the ...

  • Page 85

    You hear a click. This feature is termed the “parade” mode and is useful when headlights are required during the day. Note: if your vehicle is equipped with a touchscreen, the dimming of the touchscreen is programmable through the uconnect system. Refer to “uconnect settings” in “multi- media” for f...

  • Page 86

    Rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation. Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper opera- tion. Intermittent wiper system the intermittent feature of this sy...

  • Page 87

    Mist feature when a single wipe to clear off road mist or spray from a passing vehicle is needed, push the washer knob, located on the end of the multifunction lever, inward to the first detent and release. The wipers will cycle one time and automatically shut off. Note: the mist feature does not ac...

  • Page 88

    • transmission in neutral position — when the igni- tion is on, and the transmission is in the neutral position, the rain sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the gear selector is moved out of the neutral position. • remote...

  • Page 89

    Manual climate control descriptions icon description max a/c setting rotate the temperature control knob counterclockwise until it is set to max a/c. This is the coldest setting and will put the a/c to its maximum power. A/c button push the a/c button to engage the air conditioning (a/c). A led will...

  • Page 90

    Icon description front defrost setting turn the mode control knob to the defrost mode. Air comes from the windshield and side win- dow demist outlets. Use defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging. Rear defrost button push and release...

  • Page 91

    Icon description modes control: rotate the mode control knob to change the airflow distribution mode. The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets. The mode settings are as follows: panel mode panel mo...

  • Page 92

    Economy mode if economy mode is desired, push the a/c button to turn off the led indicator and the a/c compressor. Rotate the temperature control knob to the desired temperature. Also, make sure to select only panel, bi-level or floor modes. Caution! Failure to follow these cautions can cause damage...

  • Page 93

    Manual climate controls with a touchscreen uconnect 4c/4c nav with manual temperature controls 3 getting to know your vehicle 91.

  • Page 94

    Manual climate control with touchscreen descriptions icon description max a/c setting press the button to select max a/c. This is the coldest setting and will put the a/c to its maximum power. A/c button push the a/c button on the touchscreen or faceplate to engage the air conditioning (a/c). A led ...

  • Page 95

    Icon description front defrost setting push the button to activate defrost mode. Air comes from the windshield and side window de- mist outlets. Use defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging. Rear defrost button push and release the r...

  • Page 96

    Icon description panel mode panel mode air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction. Th...

  • Page 97

    Economy mode if economy mode is desired, push the a/c button to turn off the led indicator and the a/c compressor. Rotate the temperature control knob to the desired temperature. Also, make sure to select only panel, bi-level or floor modes. Caution! Failure to follow these cautions can cause damage...

  • Page 98

    Automatic climate controls with a touchscreen uconnect 3 with 5–inch display with automatic temperature controls 96 getting to know your vehicle.

  • Page 99

    Uconnect 4c/4c nav with automatic temperature controls 3 getting to know your vehicle 97.

  • Page 100

    Control descriptions note: icons and descriptions can vary based upon vehicle equipment. Icon description max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manua...

  • Page 101

    Icon description auto button — if equipped automatically controls the interior cabin temperature by adjusting airflow distribution and amount. Toggling this function will cause the system to switch between manual mode and auto- matic modes. Refer to “automatic operation” for more information. Front ...

  • Page 102

    Icon description uconnect 3 uconnect 4c/4c nav driver and passenger temperature up and down buttons provides the driver and passenger with independent temperature control. Push the up arrow button on the faceplate, press the up arrow button on the touchscreen, or press and slide the temperature bar ...

  • Page 103

    Icon description faceplate knob touchscreen buttons blower control blower control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the t...

  • Page 104

    Icon description floor mode floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix mode mix mode air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy c...

  • Page 105

    Climate control functions a/c (air conditioning) the air conditioning (a/c) button allows the operator to manually activate or deactivate the air conditioning sys- tem. When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin. For improved fue...

  • Page 106

    Automatic temperature control (atc) — if equipped automatic operation 1. Push the auto button on the faceplate, or the auto button on the touchscreen on the automatic tempera- ture control (atc) panel. 2. Next, adjust the temperature you would like the system to maintain by adjusting the driver and ...

  • Page 107

    Summer operation the engine cooling system must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating. Oat coolant (conforming to ms.90032) is recommended. Winter operation to ensure the best possible heater and defroster...

  • Page 108

    Operating tips chart 106 getting to know your vehicle.

  • Page 109

    Windows power windows — if equipped the power window controls located on the driver’s door trim panel have up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passen- ger window control and on the rear do...

  • Page 110

    First detent, release, and the window will go down auto- matically. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly. To open th...

  • Page 111

    3. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Window lockout switch (4–door models only) the window lockout switch on the driver’s door allows you to disable ...

  • Page 112

    Power sunroof — if equipped the power sunroof switch is located on the overhead console between the courtesy/reading lights. Warning! • never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to ...

  • Page 113

    Manual to open the sunroof, push and hold the switch rearward to full open. Any release of the switch will stop the move- ment. The sunroof and sunshade will remain in a partially opened condition until the sunroof switch is pushed again. Closing sunroof express push the switch forward and release i...

  • Page 114

    Venting sunroof — express push and release the vent button within one half second and the sunroof will open to the vent position. This is called “express vent” and it will occur regardless of sunroof position. During express vent operation, any movement of the switch will stop the sunroof. Sunroof m...

  • Page 115

    2. Reach into the opening beneath the center of the hood and push the safety latch lever to the left to release it, before raising the hood. To close the hood lower the hood to approximately 12 inches (30 cm) from the engine compartment and drop it. Make sure that the hood is completely closed. Warn...

  • Page 116

    Garage door opener — if equipped homelink replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting or home security systems. The homelink unit is powered by your vehicles 12 volt battery. The homelink buttons that are located in the over...

  • Page 117

    Before you begin programming homelink ensure your vehicle is parked outside of the garage before you begin programming. For efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is ...

  • Page 118

    1. Turn the ignition switch to the on/run position. Note: for vehicles equipped with keyless enter-n-go, place the ignition in the run position with the engine on. Make sure while programming homelink with the engine on that your vehicle is outside of your garage, or that the garage door remains ope...

  • Page 119

    6. Return to the vehicle and push the programmed homelink button twice (holding the button for two seconds each time). The instrument cluster display will show “channel # transmit.” if the garage door opener/device activates, programming is complete. Note: if the garage door opener/device does not a...

  • Page 120

    5. Push and hold the programmed homelink button. The instrument cluster display will display “channel # transmit.” if the garage door opener/device acti- vates, programming is complete. To program the remaining two homelink buttons, repeat each step for each remaining button. Do not erase the channe...

  • Page 121

    4. Continue to hold both buttons until the instrument cluster display changes from “channel # train- ing” to “channel # trained,” then release both buttons. Note: • it may take up to 30 seconds or longer in some cases for the channel to train. • if the instrument cluster display shows “did not train...

  • Page 122

    Security it is advised to erase all channels before you sell or turn in your vehicle. To erase the channels press and hold the two outside homelink buttons (i and iii) for up 20 seconds. The instrument cluster display will display “clearing channels.” release the buttons when the instrument cluster ...

  • Page 123

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 124

    To open the upper glove compartment, push upward on the handle release. The glove compartment door will automatically open. To open the lower glove compartment, pull the release handle. Upper glove compartment lower glove compartment 122 getting to know your vehicle.

  • Page 125

    Door storage front door storage — if equipped storage areas and bottle holders (driver’s side only) are located in the door trim panels. Rear door storage — if equipped storage compartments are located in both the driver and passenger rear door trim panels. Center storage compartment — if equipped t...

  • Page 126

    Warning! • this armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or a collision. Only use the center seating position when the armrest is fully upright. • in a collision, the latch may open if the total weight of the items stored exceeds about ...

  • Page 127

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a colli- sion. The center console is equipped with a front storage bin located next to the cupholders. This storage bin may be equipped wi...

  • Page 128

    Seatback storage located in the back of both the driver and passenger front seats are pockets that can be used for storage. Second row in-floor storage bin — if equipped in-floor storage bins are located in front of the second row seats and can be used for extra storage. The storage bins have remova...

  • Page 129

    To open in-floor storage bin, lift upward on the handle of the latch and open the lid. Note: the front seat may have to be moved forward to fully open the lid. Storage bin (regular cab) the storage bin is located behind the front seats and runs the length of the cab. Opened storage bin storage bin 3...

  • Page 130

    Fold flat load floor — if equipped quad cab and crew cab models with a 60/40 rear seat may be equipped with a folding load floor. Warning! Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience abrupt stopping, rapid acceleration, or ...

  • Page 131

    3. Reverse the procedure to store the load floor. Unfolding the load floor/crew cab 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unfold both the legs using the straps. Load floor in open position load floor legs in stowed position 3 getting to know your vehicle 129.

  • Page 132

    3. Lift the front panel until the load floor unfolds into position. 4. Reverse the procedure to store the load floor. Positioning the load floor for storage access under the seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load ...

  • Page 133

    Warning! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury. Quad cab — if equipped crew cab — if equipped 4. Reverse the procedure to put the load floor back in the secured down position be...

  • Page 134

    To open the storage compartments, unsnap the securing snap located at either side of the load floor and lift upward on the fold flat lid. Note: for more information on storage and the fold flat floor, refer to “fold flat load floor” in this section. Cupholders front seat cupholders for vehicles equi...

  • Page 135

    Rear cupholders — if equipped some vehicles are equipped with rear cupholders located in the center armrest. Some vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passenger convenience. Electrical power outlets the auxiliary 12 volt (13 amp) power outlets can pr...

  • Page 136

    A key symbol indicates that the key must be in the on/run or acc positions for the outlet to provide power. The battery symbol indicates that the outlet is connected to the battery, and can provide power at all times. Note: to ensure proper operation, a mopar knob and element must be used. Caution! ...

  • Page 137

    • center console when equipped with bucket seats. • rear of the center console storage compartment — quad cab or crew cab. Power outlet — center console power outlet — rear center console 3 getting to know your vehicle 135.

  • Page 138

    When the vehicle is turned off, be sure to unplug any equipment as to not drain the battery of the vehicle. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge. Power outlet — rear center console fuse powe...

  • Page 139

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 140

    To turn on the power outlet, simply plug in the device. The outlet automatically turns off when the device is un- plugged. Note: • the power inverter will only turn on if the ignition is in the acc or on/run position • due to built-in overload protection, the power inverter will shut down if the pow...

  • Page 141

    You have the ability to configure the functionality of the auxiliary switches via the instrument cluster display. All switches can now be configured for setting the switch type operation to latching or momentary, power source of either battery or ignition, and ability to hold last state across key c...

  • Page 142

    Box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor. Warning! • the pickup box is intended for load carrying pur- poses only, not for passengers, who should sit in seats and use seat belts. • care should always be exercised when operating a vehicl...

  • Page 143

    A touchscreen button ⬙x⬙ to disable display of the camera image is made available when the vehicle is not in re- verse gear. A display timer is initiated when the cargo camera image is displayed. The image will continue to be displayed until the display timer exceeds 10 seconds and the vehicle speed...

  • Page 144

    Caution! Failure to follow the following items could cause damage to the vehicle: • assure that all cargo inside the storage bins is properly secured. • do not exceed cargo weight rating of 150 lb (68 kg) 1500 series vehicles or 300 lbs (136 kg) for 2500 and 3500 series vehicles per bin. To open a s...

  • Page 145

    Caution! Leaving the lid open for extended periods of time could cause the vehicle battery to discharge. If the lid is required to stay open for extended periods of time, it is recommended that the bin lights be turned off manually using the on/off switch. The interior of the rambox will automatical...

  • Page 146

    Be locked using the vehicle key. To lock and unlock the storage bin, insert the key into the keyhole on the push button and turn clockwise to lock or counterclockwise to unlock. Always return the key to the upright (vertical) position before removing the key from the push button. Caution! • ensure c...

  • Page 147

    Rambox storage bin cover emergency release lever — if equipped as a security measure, a storage bin cover emergency release is built into the storage bin cover latching mecha- nism. Note: in the event of an individual being locked inside the storage bin, the storage bin cover can be opened from insi...

  • Page 148

    To install the bed extender into the storage position, perform the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates. 2. With the side gates open, position the extender fully forward in the bed again...

  • Page 149

    3. Rotate the side gates closed allowing the outboard ends to be positioned in front of the cargo tie down loops. 4. Rotate the center handle horizontally to secure the side gates in the closed position. 5. Lock the center handle using the vehicle key to secure the panel into place. Divider position...

  • Page 150

    To install the bed extender into a divider position, perform the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates. 2. With the side gates open, position the extender so the outboard ends align with ...

  • Page 151

    5. Lock the center handle to secure the panel into place. Extender position the extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add an additional 15 inches (38 cm) in the back of the truck when additional cargo room is needed. The extender positi...

  • Page 152

    3. Fit the end of the side gate ends onto the pin and handle. 4. Rotate the handles to the horizontal position to secure into place. Warning! To reduce the risk of potential injury or property damage: • cargo must be secured. • do not exceed cargo load rating of your vehicle. • secure all loads to t...

  • Page 153

    Warning! (continued) • when vehicle is in motion do not exceed 150 lbs (68 kg) load on the tailgate. • the bed extender is not intended for off road use. • when not in use, the extender/divider should be in stowed or divider position with the tailgate closed. • when in use all handles are to be in t...

  • Page 154

    To remove the cleats from the utility rail, remove the end cap screw located in the center of the end cap, using a #t30 torx head driver. Remove the end cap and slide the cleat off the end of the rail. Slide-in campers camper applications certain truck models are not recommended for slide-in campers...

  • Page 155

    Easy-off tailgate to simplify mounting of a camper unit with an overhang, the tailgate can be removed. Note: if your vehicle is equipped with a rear camera or remote keyless entry, the electrical connector must be disconnected prior to removing the tailgate. Disconnecting the rear camera or remote k...

  • Page 156

    3. Disconnect the chassis wiring harness, ensuring the connector bracket does not fall into the sill. 4. Connect the chassis plug and bracket (provided in the glove compartment) to the chassis wiring harness and insert the bracket back into the sill. 5. Connect the tailgate plug (provided in the glo...

  • Page 157

    3. Position the tailgate on a 45 degree angle. 4. Raise the right side of the tailgate until the right side pivot clears the hanger bracket. 5. Slide the entire tailgate to the right to free the left side pivot. 6. Remove the tailgate from the vehicle. Note: do not carry the tailgate loose in the tr...

  • Page 158

    Note: the tonneau cover can be folded up and secured at the front of the box without removing completely. Tri-fold tonneau cover removal to remove the tonneau cover follow the following steps: 1. Lower the tailgate to gain access to the first set of two tonneau cover clamps located on the driver and...

  • Page 159

    Caution! Make sure the tonneau cover clamp and clamp wire are in the proper released position. If the clamp and clamp wire are not properly released, damage to the tonneau cover material will result. 4. Pick up on the tonneau cover and fold it back onto the second panel. 5. Pick up on the cover and ...

  • Page 160

    6. Once in the third panel position, pull down on the second set of clamps on both driver and passenger sides to the semi clamped position. 7. Pull down on the clamp wire and push the clamp up into the proper released position. Third panel position semi clamped position 158 getting to know your vehi...

  • Page 161

    8. Be sure to clip both stowage straps together to ensure the cover stays together. 9. With two people, remove the cover. Note: be sure the tonneau cover has been folded com- pletely before removing. Tri-fold tonneau cover installation to install the tonneau cover follow the following steps: 1. Posi...

  • Page 162

    2. Pull down on the first set of clamp handles to release the clamps from the stowed position. 3. Push clamp wires up and under the flange of box (or flange of ram box rail, if equipped) to the semi clamped position. Stowed position semi clamped position 160 getting to know your vehicle.

  • Page 163

    4. Push clamp handles upward to the clamped position to properly engage the clamps. Note: once clamped, be sure the clamps are not partially clamped to the truck bed flange. 5. Disengage the stowage straps. Clamped position improper clamp position 3 getting to know your vehicle 161.

  • Page 164

    6. Unfold tonneau cover to the intermediate position. Note: the vehicle cannot be driven when the tonneau cover is in this position. 7. Completely unfold the tonneau cover. Intermediate position (vehicle cannot be driven) fully unfolded position 162 getting to know your vehicle.

  • Page 165

    8. Pull down on the second set of clamp handles to release the clamps from the stowed position. 9. Push clamp wires up and under the flange of box (or flange of ram box rail, if equipped) to the semi clamped position. Stowed position semi clamped position 3 getting to know your vehicle 163.

  • Page 166

    10. Push clamp handles upward to the clamped position to properly engage the clamps. Note: once clamped, be sure the clamps are not partially clamped to the truck bed flange. Clamped position improper clamp position 164 getting to know your vehicle.

  • Page 167

    The tonneau cover clamps can be locked when in the clamped position by placing a lock through the locking hole. Caution! It is the driver’s responsibility to ensure the tonneau cover is properly installed on the vehicle. Failure to follow this procedure can result in detachment of the tonneau cover ...

  • Page 169: Contents

    Getting to know your instrument panel contents 䡵 base instrument cluster . . . . . . . . . . . . . .168 ▫ base instrument cluster descriptions . . . . . . . . .169 䡵 premium instrument cluster . . . . . . . . . .170 ▫ premium instrument cluster descriptions . . . . .171 䡵 instrument cluster display ...

  • Page 170

    Base instrument cluster base instrument clusters 168 getting to know your instrument panel.

  • Page 171

    Base instrument cluster descriptions 1. Tachometer • indicates the engine speed in revolutions per minute (rpm x 1000). 2. Instrument cluster display • when the appropriate conditions exist, this display shows the instrument cluster display messages. Refer to “instrument cluster display” in “getting...

  • Page 172

    Premium instrument cluster premium instrument clusters 170 getting to know your instrument panel.

  • Page 173

    Premium instrument cluster descriptions 1. Tachometer • indicates the engine speed in revolutions per minute (rpm x 1000). 2. Voltmeter • when the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the battery is charged. If the p...

  • Page 174

    Allowed to exceed the upper limits of the normal operating range. Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood ...

  • Page 175

    Instrument cluster display controls the instrument cluster display features a driver-interactive display that is located in the instrument cluster. The instrument cluster display menu items may consist of the following: • speedometer • vehicle info • fuel economy info • trip a • trip b • audio • tra...

  • Page 176

    • stored messages • screen setup • vehicle settings (not equipped with a uconnect touch- screen radio) the system allows the driver to select information by pushing the following instrument cluster display control buttons located on the left side of the steering wheel: • up arrow button push and rel...

  • Page 177

    Display menu screens the instrument cluster display screens are located in the center portion of the cluster and consists of seven sections: 1. Compass display displays the current direction. Refer to “uconnect set- tings” in “multimedia” for further information. 2. Temperature display displays the ...

  • Page 178

    The instrument cluster display screens are located in the center portion of the cluster and consists of eight sections: 1. Main screen — the inner ring of the display will illuminate in grey under normal conditions, yellow for non critical warnings, red for critical warnings, and white for on demand...

  • Page 179

    Of this message type are “turn signal on” (if a turn signal is left on) and “lights on” (if driver leaves the vehicle). • unstored messages until run these messages deal primarily with the remote start feature. This message type is displayed until the ignition is in the run state. Examples of this m...

  • Page 180

    2. Push and release the down arrow button to scroll downward through the main menu to “vehicle info.” 3. Push and release the right arrow button to access the “vehicle info” screen then scroll up or down to select “oil life.” 4. Push and hold the right arrow button to select “yes” by pushing the rig...

  • Page 181

    • service electronic throttle control • lights on • right turn signal light out • left turn signal light out • turn signal on • sound horn with remote lock: off; 1st press; 2nd press • vehicle not in park • key in ignition • key in ignition lights on • remote start active key to run • remote start a...

  • Page 182

    • engage park brake to prevent rolling • transmission too cold idle with engine on • washer fluid low • service air suspension system • heavy duty air suspension system disabled • selected ride height not permitted due to speed • selected ride height not permitted due to payload • selected ride heig...

  • Page 183

    Cluster display. Push and release the right arrow button to enter the submenus items of vehicle info. Follow the directional prompts to access or reset any of the following vehicle info submenu items: • tire pressure • transmission temp (automatic only) • oil temp • oil life • air suspension — if eq...

  • Page 184

    • output • type • gain audio push and release the up or down arrow button until the audio display icon is highlighted in the instrument cluster display. Push and release the right arrow button to display the active source. Stored messages push and release the up or down arrow button until the messag...

  • Page 185

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 1 language select language english, spanish, french, italian, german, dutch, portuguese, arabic (if equipped) 2 units units u.S.; metric 3 parksense parksense • notification — sound only; sound & display • f...

  • Page 186

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 12 auto lock doors auto lock doors on; off 13 auto unlock doors auto unlock doors on; off 14 sound horn with remote start horn w/ rmt start on; off 15 sound horn with remote lock horn w/ rmt lock off; 1st pr...

  • Page 187

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 22 commercial settings commercial • aux switches • power take-off • pin setup note: if the vehicle’s pin is forgotten or not known, see an authorized dealer to have the pin reset. 23 air suspension display a...

  • Page 188

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 32 trailer name trailer name • trailer # (# is equal to slot position) • boat • car • cargo • dump • equipment • flatbed • gooseneck • horse • livestock • motorcycle • snowmobile • travel • utility • 5th whe...

  • Page 189

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 36 park assist front chime volume park assist front chime volume on; off 37 park assist rear chime volume park assist rear chime volume on; off turn menu off — if equipped push and release the right arrow bu...

  • Page 190

    Note: • the charging system is independent from load reduc- tion. The charging system performs a diagnostic on the charging system continuously. • if the battery charge warning light is on it may indicate a problem with the charging system. Refer to “battery charge warning light” in “getting to know...

  • Page 191

    What to do when an electrical load reduction action message is present (“battery saver on” or “battery saver mode”) during a trip: • reduce power to unnecessary loads if possible: – turn off redundant lights (interior or exterior) – check what may be plugged in to power outlets +12v, 115v ac, usb po...

  • Page 192

    — brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system r...

  • Page 193

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run position. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. — vehicle security warning light — if equipped this light will flash at a fa...

  • Page 194

    And the transmission is placed in the park position. The light should turn off. If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible. Note: this light may turn on if the accelerator and brake pedals...

  • Page 195

    Come on when turning the ignition switch from off to on/run, have the condition checked promptly. Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several typical...

  • Page 196

    Your authorized dealer as soon as possible to have the problem diagnosed and corrected. • the “esc off indicator light” and the “esc indicator light” come on momentarily each time the ignition is placed in the on/run or acc/on/run position. • the esc system will make buzzing or clicking sounds when ...

  • Page 197

    On the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) as an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more o...

  • Page 198

    Caution! (continued) monitoring system (tpms) sensor to become inoper- able. After using an aftermarket tire sealant it is recommended that you take your vehicle to your au- thorized dealer to have your sensor function checked. — low fuel indicator light when the fuel level reaches approximately 3.0...

  • Page 199

    Warning! If you continue operating the vehicle when the trans- mission temperature warning light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. Caution! Continuous driving with the transmission tempera- ture warning ligh...

  • Page 200

    — air suspension ride height lowering indicator light— if equipped this light will blink and alert the driver that the vehicle is changing to a lower ride height. — air suspension entry/exit indicator light— if equipped this light comes on when the vehicle is automatically lowered from ride height p...

  • Page 201

    — speed control set indicator light — if equipped with 7 inch instrument cluster display this light will turn on when the speed control is set. Refer to “speed control” in “starting and operating” for further information. – 4wd auto indicator light — if equipped this light alerts the driver that the...

  • Page 202

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and transmission control systems. When these systems are operating prop- erly, your vehicle will provide excellent ...

  • Page 203

    Warning! (continued) vehicle control could occur that may result in an accident involving serious injury or death. • access, or allow others to access, information stored in your vehicle systems, including personal information. For further information, refer to “cybersecurity” in “mul- timedia”. Emi...

  • Page 204

    • the mil will not flash at all and will remain fully illuminated until you place the ignition in the off posi- tion or start the engine. This means that your vehicle’s obd ii system is ready and you can proceed to the i/m station. If your obd ii system is not ready, you should see your authorized d...

  • Page 205: Safety

    Safety contents 䡵 safety features . . . . . . . . . . . . . . . . . . . . . .204 ▫ anti-lock brake system (abs) . . . . . . . . . . . . .204 ▫ electronic brake control system . . . . . . . . . . . .205 䡵 auxiliary driving systems . . . . . . . . . . . . .216 ▫ tire pressure monitoring system (tpms) ...

  • Page 206

    Safety features anti-lock brake system (abs) the anti-lock brake system (abs) provides increased vehicle stability and brake performance under most brak- ing conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking. The abs performs a self-check cycle to ...

  • Page 207

    Warning! (continued) • the capabilities of an abs equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user’s safety or the safety of others. Abs is designed to function with the oem tires. Modifica- tion may result in degraded abs performance. Anti-lo...

  • Page 208

    Brake system warning light the red “brake system warning light” will turn on when the ignition is turned to the on/run mode and may stay on for as long as four seconds. If the “brake system warning light” remains on or comes on while driving, it indicates that the brake system is not functioning pro...

  • Page 209

    The following conditions must be met in order for hsa to activate: • the feature must be enabled. • the vehicle must be stopped. • park brake must be off. • driver door must be closed. • the vehicle must be on a sufficient grade. • the gear selection must match vehicle uphill direction (i.E., vehicl...

  • Page 210

    Warning! (continued) order to avoid rolling down an incline while resum- ing acceleration, manually activate the trailer brake or apply more vehicle brake pressure prior to releas- ing the brake pedal. • hsa is not a parking brake. Always apply the parking brake fully when exiting your vehicle. Also...

  • Page 211

    Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, the tcs may apply brake pressure to the spinning wheel(s) and/or reduce engine power to provide enhanced acceleration and stability. A feature of the tcs, brake limite...

  • Page 212

    Warning! (continued) road conditions. Esc cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slippery surfaces, or hydro- planing. Esc also cannot prevent accidents resulting from loss of vehicle control due to inappropriate driver input for the cond...

  • Page 213

    Note: for vehicles with multiple partial esc modes a momentary button push will toggle the esc mode. Mul- tiple momentary button pushed may be required to return to esc on. Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature described in the tcs ...

  • Page 214

    Warning! (continued) off” mode is only intended for off-highway or off- road use. • the electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent all accident...

  • Page 215

    • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation. The “esc off indicator light” indicates the customer has elected to have the electronic sta- bility control (...

  • Page 216

    Note: tsc cannot stop all trailers from swaying. Always use caution when towing a trailer and follow the trailer tongue weight recommendations. Refer to “trailer tow- ing” in “starting and operating” for further information. When tsc is functioning, the “esc activation/ malfunction indicator light” ...

  • Page 217

    • r = 0.6 mph (1 km/h) • n = 1.2 mph (2 km/h) • d = 0.6 mph (1 km/h) • 1st = 0.6 mph (1 km/h) • 2nd = 1.2 mph (2 km/h) • 3rd = 1.8 mph (3 km/h) • 4th = 2.5 mph (4 km/h) • 5th = 3.1 mph (5 km/h) • 6th = 3.7 mph (6 km/h) • 7th = 4.3 mph (7 km/h) • 8th = 5.0 mph (8 km/h) • 9th = 5.6 mph (9 km/h) – if e...

  • Page 218

    • the vehicle is driven greater than 20 mph (32 km/h) for greater than 70 seconds. • the vehicle is driven greater than 40 mph (64 km/h) (hdc exits immediately). • hdc detects excessive brake temperature. Feedback to the driver the instrument cluster has an hdc icon and the hdc switch has an led ico...

  • Page 219

    Refer to “tires” in “servicing and maintenance” for infor- mation on how to properly inflate the vehicle’s tires. The tire pressure will also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pressure. The tpms will warn the driver of a low tire ...

  • Page 220

    Caution! (continued) equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. • using aftermarket tire sealants may cause the tire pressure monit...

  • Page 221

    The tpms consists of the following components: • receiver module • four tire pressure monitoring sensors • various tire pressure monitoring system messages, which display in the instrument cluster • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the “tire pres...

  • Page 222

    Service tpms warning if a system fault is detected, the “tire pressure monitoring telltale light” will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime. In addition, the instrument cluster will display a ⬙service tpm system ⬙ message for a minimum of...

  • Page 223

    Flash and the tire pressure display screen will be displayed showing the tire pressure values the correct locations. Vehicles with non matching full size spare or compact spare • the non matching full size spare or compact spare tire does not have a tpm sensor. Therefore, the tpms will not monitor t...

  • Page 224

    Transmit tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the receiver module. Note: it is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure. The tp...

  • Page 225

    2. This device must accept any interference received, in- cluding interference that may cause undesired opera- tion. Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Occupant restraint systems some...

  • Page 226

    6. All occupants should always wear their lap and shoul- der belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate. 8. Do not lean against the door or window. If your vehicle has side air bags, and deployment occu...

  • Page 227

    A few seconds. If the driver or outboard front seat passen- ger (if equipped with outboard front passenger seat beltalert) is unbuckled when the ignition switch is first in the start or on/run position the seat belt reminder light will turn on and remain on until both outboard front seat belts are b...

  • Page 228

    Lap/shoulder belts all seating positions except the quad cab, mega cab and crew cab front center seating position have combination lap/shoulder belts. The seat belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoulder part of the seat belt to move...

  • Page 229

    Warning! • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not protect you pro...

  • Page 230

    Equipped with a rear seat). Grasp the latch plate and pull out the seat belt. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Positi...

  • Page 231

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automatically ...

  • Page 232

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 233

    Stored out of the way in the seat for added convenience to open up utilization of the storage areas behind the front seats when the seat is not occupied. 1. Remove the mini-latch plate and regular latch plate from its stowed position on the seat. 2. Grasp the mini-latch plate and pull the seat belt ...

  • Page 234

    6. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 7. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 235

    Warning! (continued) procedure to detach the mini-latch plate and mini- buckle, untwist the webbing, and reattach the mini- latch plate and mini-buckle. First row center lap belt operating instructions — if equipped the center seating position for the quad cab, mega cab and crew cab front seat has a...

  • Page 236

    Seat belts and pregnant women seat belts must be worn by all occupants including preg- nant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong...

  • Page 237

    Switchable automatic locking retractors (alr) the seat belts in the passenger seating positions may be equipped with a switchable automatic locking retractor (alr) which is used to secure a child restraint system. For additional information, refer to “installing child restraints using the vehicle se...

  • Page 238

    Webbing necessary to comfortably wrap around the occu- pant’s mid-section. Slide the latch plate into the buckle until you hear a ⬙click.⬙ in automatic locking mode, the shoulder belt is automati- cally pre-locked. The seat belt will still retract to remove any slack in the shoulder belt. Use the au...

  • Page 239

    Supplemental restraint systems (srs) some of the safety features described in this section may be standard equipment on some models, or may be optional equipment on others. If you are not sure, ask your autho- rized dealer. The air bag system must be ready to protect you in a collision. The occupant...

  • Page 240

    Light, either momentarily or continuously. A single chime will sound to alert you if the light comes on again after initial startup. The orc also includes diagnostics that will illuminate the instrument panel air bag warning light if a malfunction is detected that could affect the air bag system. Th...

  • Page 241

    Warning! • being too close to the steering wheel or instrument panel during front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. (continued) warning! (continued)...

  • Page 242

    Buckle switch may adjust the inflation rate of the ad- vanced front air bags. Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inf...

  • Page 243

    Inflate in less time than it takes to blink your eyes. The front air bags then quickly deflate while helping to restrain the driver and front passenger. Knee impact bolsters the knee impact bolsters help protect the knees of the driver and front passenger, and position the front occu- pants for impr...

  • Page 244

    And the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the sab inflates. Children are at an even greater risk of injury from a deploying air bag. Warning! Do not use acce...

  • Page 245

    Positioned in the area where the sabics inflate. Children are at an even greater risk of injury from a deploying air bag. The sabics may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain side impact events. Warning! • do not mount equipment, or...

  • Page 246

    Side air bags are a supplement to the seat belt restraint system. Side air bags deploy in less time than it takes to blink your eyes. Warning! • occupants, including children, who are up against or very close to side air bags can be seriously injured or killed. Occupants, including children, should ...

  • Page 247

    The side air bags will not deploy in all rollover events. The rollover sensing-system determines if a rollover event may be in progress and whether deployment is appropriate. A slower-developing event may deploy the seat belt preten- sioners on both sides of the vehicle. A faster-developing event ma...

  • Page 248

    And the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the sab inflates. Children are at an even greater risk of injury from a deploying air bag. Warning! Do not use acce...

  • Page 249

    Positioned in the area where the sabics inflate. Children are at an even greater risk of injury from a deploying air bag. The sabics (if equipped with sabics) may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain side impact events. Warning! • ...

  • Page 250

    Side air bags are a supplement to the seat belt restraint system. Side air bags deploy in less time than it takes to blink your eyes. Warning! • occupants, including children, who are up against or very close to side air bags can be seriously injured or killed. Occupants, including children, should ...

  • Page 251

    The side air bags will not deploy in all rollover events. The rollover sensing-system determines if a rollover event may be in progress and whether deployment is appropriate. A slower-developing event may deploy the seat belt preten- sioners on both sides of the vehicle. A faster-developing event ma...

  • Page 252

    • as the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the are...

  • Page 253

    Enhanced accident response system reset procedure in order to reset the enhanced accident response system functions after an event, the ignition switch must be changed from ignition start or on/run to ignition off. Carefully check the vehicle for fuel leaks in the engine compartment and on the groun...

  • Page 254

    And safety systems for a short period of time, typically 30 seconds or less. The edr in this vehicle is designed to record such data as: • how various systems in your vehicle were operating; • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if at all) the drive...

  • Page 255

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in...

  • Page 256

    Child size, height, weight or age recommended type of child restraint larger children children who have outgrown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt belt positioning booster seat and the vehicle seat belt, seated in the rear seat of the veh...

  • Page 257

    Warning! Do not install a rear-facing car seat using a rear support leg in this vehicle. The floor of this vehicle is not designed to manage the crash forces of this type of car seat. In a crash, the support leg may not function as it was designed by the car seat manufacturer, and your child may be ...

  • Page 258

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • after a child restraint i...

  • Page 259

    Warning! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death. A child must always wear both the lap and shoulder portions of the seat belt correctly. Recommendatio...

  • Page 260

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchorage system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch-equipped child seats. There ...

  • Page 261

    Crew/mega cabs 60/40 split bench latch positions top tether anchorage symbol lower anchorage symbol (2 anchorages per seating position) quad cab 60/40 split bench latch positions top tether anchorage symbol lower anchorage symbol (2 anchorages per seating position) 5 safety 259.

  • Page 262

    Frequently asked questions about installing child restraints with latch what is the weight limit (child’s weight + weight of the child re- straint) for using the latch anchor- age system to attach the child re- straint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the...

  • Page 263

    Frequently asked questions about installing child restraints with latch can the latch anchorages and the seat belt be used together to attach a rear-facing or forward-facing child restraint? No do not use the seat belt when you use the latch anchorage system to attach a rear-facing or forward-facing...

  • Page 264

    Frequently asked questions about installing child restraints with latch can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint ...

  • Page 265

    Locating the upper tether anchorages regular cab models have tether strap anchor- ages behind the front center and right seats. Quad cab, mega cab and crew cab models have tether strap anchorages located behind each of the rear seats. 1 — tether strap hook 2 — tether strap to child restraint 3 — tet...

  • Page 266

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear- facing child restraint...

  • Page 267

    Center seat latch regular cab, quad cab, or crew cab full bench rear seat: no lower center latch anchorages available warning! • do not install a child restraint in the center position using the latch system. This position is not ap- proved for installing child seats using the latch attachments. You...

  • Page 268

    Forward and rearward in the vehicle, you may wish to move it to its rear-most position to make room for the child seat. You may also move the front seat forward to allow more room for the child seat. 3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the select...

  • Page 269

    Warning! (continued) • child restraint anchorages are designed to withstand only those loads imposed by correctly-fitted child restraints. Under no circumstances are they to be used for adult seat belts, harnesses, or for attaching other items or equipment to the vehicle. Installing child restraints...

  • Page 270

    Please see the table below and the following sections for more information. Lap/shoulder belt systems for installing child restraints in this vehicle regular cab automatic locking retractor (alr) locations alr = switchable automatic locking retractor top tether anchorage symbol quad cab/mega cab/cre...

  • Page 271

    Frequently asked questions about installing child restraints with seat belts what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tethe...

  • Page 272

    1. For crew, mega, and quad cab models place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move ...

  • Page 273

    Installing a child restraint with a cinching latch plate (cinch) — if equipped: child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt. Warning! • improper installation or failure to properly secure a child restraint can lead t...

  • Page 274

    Plate into the buckle with the release button facing out, away from the child restraint. Repeat steps 4 to 6, above, to complete the installation of the child restraint. If the belt still cannot be tightened after you shorten the buckle, disconnect the latch plate from the buckle, turn the buckle ar...

  • Page 275

    2. Route the tether strap to provide the most direct path between the anchorage and the child seat. The tether strap should go between the head restraint posts under- neath the head restraint. You may need to adjust the head restraint to the upward position to pass the tether strap underneath the he...

  • Page 276

    Quad cab or crew cab trucks: the top tether anchorages in this vehicle are tether strap loops located between the rear glass and the back of the rear seat. There is a tether strap loop located behind each seating position. Follow the steps below to attach the tether strap of the child restraint. Rig...

  • Page 277

    4. Attach the hook to the center tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s instructions. Note: if there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connecte...

  • Page 278

    Center seat: 1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop. 2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint, through the tether strap loop behind the sea...

  • Page 279

    4. Attach the hook to the outboard tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s instructions. Installing three child restraints: 1. Place a child restraint on each outboard rear seat. Route the tether straps following the directions for right a...

  • Page 280

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly be- hind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tet...

  • Page 281

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can even- tually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confin...

  • Page 282

    Have the system inspected at your authorized dealer as soon as possible. After the bulb check, this light will illuminate with a single chime when a fault with the air bag system has been detected. It will stay on until the fault is cleared. If the light comes on intermittently or remains on while d...

  • Page 283

    Warning! (continued) vehicle properly parked with the engine off, fully depress the accelerator, the brake, and the clutch pedal (if present) to check for interference. If your floor mat interferes with the operation of any pedal, or is not secure to the floor, remove the floor mat from the vehicle ...

  • Page 284

    Door latches check for proper closing, latching, and locking. Fluid leaks check area under the vehicle after overnight parking for fuel, coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, or brake fluid leaks are suspected. The cause should be located and corrected ...

  • Page 285: Starting And Operating

    Starting and operating contents 䡵 starting the engine — gasoline engine . . . . . . . . . . . . . . . . . . . . .288 ▫ automatic transmission . . . . . . . . . . . . . . . . . .288 ▫ tip start feature . . . . . . . . . . . . . . . . . . . . . . .289 ▫ keyless enter-n-go — ignition . . . . . . . . . ...

  • Page 286

    ▫ four-position electronically shifted transfer case (eight speed transmission only) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .336 ▫ five-position electronically shifted transfer case (eight speed transmission only) — if equipped . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 287

    ▫ airing down for off-road driving . . . . . . . . . .371 ▫ vehicle recovery . . . . . . . . . . . . . . . . . . . . . . .372 ▫ after driving off-road. . . . . . . . . . . . . . . . . . .375 䡵 limited-slip differential . . . . . . . . . . . . . .375 䡵 winch usage — power wagon only (if equipped) . ....

  • Page 288

    ▫ parksense warning display. . . . . . . . . . . . . . . .405 ▫ parksense display . . . . . . . . . . . . . . . . . . . . . .405 ▫ enabling and disabling front and/or rear parksense . . . . . . . . . . . . . . . . . . . . . . . . . . . .407 ▫ service the parksense park assist system . . . . .407 ▫ c...

  • Page 289

    䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . . . . .436 ▫ towing this vehicle behind another vehicle. . . .436 ▫ recreational towing — two-wheel drive models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .437 ▫ recreational towing — four-wheel drive mode...

  • Page 290

    Starting the engine — gasoline engine before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 10-second intervals. Waiting a few seconds between such intervals will protect the starter from ov...

  • Page 291

    Tip start feature do not press the accelerator. Cycle the ignition switch briefly to the start position and release it. The starter motor will continue to run and will automatically disen- gage when the engine is running. Keyless enter-n-go — ignition this feature allows the driver to operate the ig...

  • Page 292

    3. If the gear selector is not in park, the engine start/ stop button must be held for two seconds or three short pushes in a row with the vehicle speed above 5 mph (8 km/h) before the engine will shut off. The ignition will remain in the acc mode until the gear selector is in park and the button is...

  • Page 293

    Warning! • driver inattention could lead to failure to place the vehicle in park. Always do a visual check that your vehicle is in park by verifying that a solid (not blinking) “p” is indicated in the instrument cluster display and near the gear selector. If the ⴖpⴖ indicator is blinking, your vehic...

  • Page 294

    Note: in some cases the parksense graphic will be displayed in the instrument cluster, causing the “ au- topark engaged shift to p then shift to gear ” to not be seen. In these cases, the shifter must be returned to “p” to select desired gear. If the driver shifts into park while moving, the vehicle...

  • Page 295

    Idle shutdown — 6.4l engine only this feature can be enabled so that the truck will automati- cally shutdown when the truck has been idling for a set period of time when the engine is at operating tempera- ture. Idle time can be set in 5 minute increments between 5 and 60 minutes. See your local aut...

  • Page 296

    If the engine has been flooded, it may start to run, but not have enough power to continue running when the ignition button/key is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the ignition button/key once th...

  • Page 297

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 298

    When the parking brake is applied with the ignition switch on, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound...

  • Page 299

    Warning! (continued) acc or on/run mode. A child could operate power windows, other controls, or move the vehicle. • be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • always fully apply the parking brake when leaving your vehi...

  • Page 300

    Warning! (continued) • when leaving the vehicle, always make sure the ignition is in the off mode, remove the key fob from the vehicle, and lock the vehicle. • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when exiting the vehicle to guard ag...

  • Page 301

    Ignition when the ignition is in the lock/off position, and the transmission is locked in park whenever the ignition is in the lock/off position. Note: if a malfunction occurs, the system will trap the key fob in the ignition to warn you that this safety feature is inoperable. The engine can be star...

  • Page 302

    May be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers). Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting betwee...

  • Page 303

    Never attempt to use park while the vehicle is in motion. Apply the parking brake when exiting the vehicle in this range. When parking on a level surface, you may shift the transmission into park first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting...

  • Page 304

    Warning! (continued) engine is idling normally and your foot is firmly pressing the brake pedal. • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always come to a...

  • Page 305

    The following indicators should be used to ensure that you have properly engaged the transmission into the park position: • look at the transmission gear position display and verify that it indicates the park position (p), and is not blinking. • with brake pedal released, verify that the gear select...

  • Page 306

    Towing a heavy trailer), select tow/haul mode or use the electronic range select (ers) shift control (refer to ⬙electronic range select (ers) operation⬙ in this section for further information) to select a lower gear range. Under these conditions, using a lower gear range will improve performance an...

  • Page 307

    Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnos- tic equipment to assess the condition of your transmission. If the transmission cannot be reset, authorized dealer service is r...

  • Page 308

    When to use tow/haul mode when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, push the tow/haul switch to activate tow/haul mode. This will improve performance and reduce the potential for transmission overheating or failure due to e...

  • Page 309

    The electronically-controlled transmission provides a pre- cise shift schedule. The transmission electronics are self- calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilom...

  • Page 310

    • shift the transmission into park. • turn the engine off. • remove the key fob. Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage. • your vehicle...

  • Page 311

    Warning! (continued) • do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition (in a vehicle equipped with keyless enter-n-go) in the acc or on/run mode. A child could operate power windows, other controls, or move the vehicle. Caution...

  • Page 312

    Caution! Towing the vehicle, coasting, or driving for any other reason with the transmission in neutral can cause severe transmission damage. Refer to “recreational towing” in “starting and operating” and “towing a disabled vehicle” in “in case of emergency” for further information. Drive (d) this r...

  • Page 313

    During cold temperatures, transmission operation may be modified depending on engine and transmission tempera- ture as well as vehicle speed. This feature improves warm up time of the engine and transmission to achieve maxi- mum efficiency. Engagement of both the torque converter clutch and the top ...

  • Page 314

    Electronic range select (ers) operation — six-speed transmission (1500 models only) the electronic range select (ers) shift control allows the driver to limit the highest available gear when the trans- mission is in drive. For example, if you set the transmis- sion gear limit to 4 (fourth gear), the...

  • Page 315

    To exit ers mode, simply hold the gear selector to the right (+) (console shift) or press and hold the ers (+) switch (column shift) until the gear limit display disappears from the instrument cluster. Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels co...

  • Page 316

    • vehicle speed is sufficiently high, • the tow/haul switch has not been activated, and • the driver is not heavily pressing the accelerator. When to use tow/haul mode when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, push the tow/...

  • Page 317

    Warning! Do not use the “tow/haul” feature when driving in icy or slippery conditions. The increased engine brak- ing can cause the rear wheels to slide, and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possibly result- ing in personal injury or ...

  • Page 318

    The electronically-controlled transmission provides a pre- cise shift schedule. The transmission electronics are self- calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilom...

  • Page 319

    Note: on four-wheel drive vehicles be sure that the transfer case is in a drive position. When exiting the vehicle, always: • apply the parking brake. • shift the transmission into park. • turn the engine off. • remove the key fob. Warning! • never use the park position as a substitute for the parki...

  • Page 320

    Warning! (continued) of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the trans- mission gear selector. • do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not...

  • Page 321

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 322

    Climbing a grade), or shifting to neutral (when stopped in heavy traffic) can help to reduce this excess heat generation. During cold temperatures, transmission operation may be modified depending on engine and transmission tempera- ture as well as vehicle speed. This feature improves warm up time o...

  • Page 323

    Electronic range select (ers) operation the electronic range select (ers) shift control allows the driver to limit the highest available gear when the trans- mission is in drive. For example, if you set the transmis- sion gear limit to 4 (fourth gear), the transmission will not shift above fourth ge...

  • Page 324

    Note: to select the proper gear position for maximum deceleration (engine braking), simply push and hold the ers (-) switch. The transmission will shift to the range from which the vehicle can best be slowed down. Caution! When using ers for engine braking while descending steep grades, be careful n...

  • Page 325

    The “tow/haul indicator light” will illuminate in the instrument cluster to indicate that tow/haul mode has been activated. Pushing the switch a second time restores normal operation. Normal operation is always the default at engine start-up. If tow/haul mode is desired, the switch must be pushed ea...

  • Page 326

    Transmission is not shifting properly when cold. This is normal. Using the electronic range select (ers) shift control, when the transmission is sufficiently warm, will demonstrate that the transmission is able to shift into and out of overdrive. • if the vehicle has not been driven for several days...

  • Page 327

    This transfer case is intended to be driven in the 2h position for normal street and highway conditions such as dry, hard surfaced roads. When additional traction is required, the 4h and 4l positions can be used to lock the front and rear driveshafts together and force the front and rear wheels to r...

  • Page 328

    Warning! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neu- tral position without first fully engaging the park- ing brake. The transfer case neutral position disen- gages both the front and rear drive shafts from the powertrain and will a...

  • Page 329

    • shifting into or out of 4l is possible with the vehicle completely stopped, however difficulty may occur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth align- ment and shift completion to occur. The preferred method is with the vehicle ...

  • Page 330

    For additional information on the appropriate use of each transfer case mode position, see the information below: 2wd rear wheel drive high range — this range is for normal street and highway driving on dry, hard surfaced roads. 4wd lock four-wheel drive lock high range — this range maximizes torque...

  • Page 331

    The 4wd lock and 4wd low positions are designed for loose, slippery road surfaces only. Driving in the 4wd lock and 4wd low positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline components. Note: the transfer case neutral button is located on the lower left h...

  • Page 332

    Warning! Always engage the parking brake when powering down the vehicle if the “svc 4wd warning light” is illuminated. Not engaging the parking brake may allow the vehicle to roll, which may cause personal injury. Note: do not attempt to make a shift while only the front or rear wheels are spinning,...

  • Page 333

    The transfer case will engage/disengage faster if you mo- mentarily release the accelerator pedal after turning the control switch. If the vehicle is stopped, the ignition switch must be in the on position with the engine either running or off. This shift cannot be completed if the ignition switch i...

  • Page 334

    Be operable. If the ignition switch is not in the on position, the shift will not take place and no position indicator lights will be on or flashing. Electronically shifted transfer case (five-position switch) — if equipped this is an electronic shift transfer case and is operated by the 4wd control...

  • Page 335

    4wd low four-wheel drive low range — this range provides low speed four-wheel drive. It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed. This range provides additional traction and maximum pulling power for loose, slippery road surfaces only. D...

  • Page 336

    Transfer case position indicator lights the transfer case position indicator lights (4wd, 4low, and 4wd auto) are located in the instrument cluster and indicate the current and desired transfer case selection. When you select a different transfer case position, the indicator lights will do the follo...

  • Page 337

    When operating your vehicle in 4wd low, the engine speed is approximately three times that of the 2wd, 4wd auto or 4wd lock positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equ...

  • Page 338

    Four-position electronically shifted transfer case (eight speed transmission only) — if equipped this is an electronic shift transfer case and is operated by the 4wd control switch (transfer case switch), which is located on the instrument panel. This electronically shifted transfer case provides fo...

  • Page 339

    Neutral (n) neutral — this range disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “recreational towing” in this section for further information. This electronically shifted transfer case is designed to be driven in the tw...

  • Page 340

    If one or more of the following shift conditions are not met: 1. The indicator light for the current position will remain on. 2. The newly selected position indicator light will continue to flash. 3. The transfer case will not shift. Note: before retrying a selection, make certain that all the neces...

  • Page 341

    Warning! • you or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engaging the parking brake. The transfer case neutral (n) position disengages both the front and rear drive shaft from the powertrain, and wi...

  • Page 342

    This electronically shifted transfer case provides five mode positions: • two-wheel drive high range (2wd) • four-wheel drive automatic high range (4wd auto) • four-wheel drive lock high range (4wd lock) • four-wheel drive low range (4wd low) • neutral (neutral) for additional information on the app...

  • Page 343

    Same speed. This range provides additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Neutral (n) neutral — this range disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle...

  • Page 344

    Indicate the current and desired transfer case selection. When you select a different transfer case position, the indicator lights will do the following: if all of the following shift conditions are met: 1. The current position indicator light will turn off. 2. The selected position indicator light ...

  • Page 345

    Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the drivetrain. Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do ...

  • Page 346

    Air suspension system (1500 models) — if equipped description the air suspension system provides full time load leveling capability along with the benefit of being able to adjust vehicle height by the push of a button. 1 — up button 2 — down button 3 — entry/exit mode indicator (customer selectable)...

  • Page 347

    • off-road 2 (or2) (raises the vehicle approximately 2 in (51 mm)) – this position is intended for off-roading use only where maximum ground clearance is required. To enter or2, push the “up” button twice from the nrh position or once from the or1 position while vehicle speed is below 20 mph (32 km/...

  • Page 348

    In entry/exit or drive the vehicle over 15 mph (24 km/h). Entry/exit mode may not be available due to vehicle payload, an instrument cluster message will be displayed when this occurs. Refer to “instrument clus- ter display” in “getting to know your instrument panel” for further information. Note: e...

  • Page 349

    Warning! (continued) injury or damage to the system, see your authorized dealer for service. Air suspension modes the air suspension system has multiple modes to protect the system in unique situations: aero mode to improve aerodynamics, the air suspension system has a feature which will put the veh...

  • Page 350

    Protection strategy in order to “protect” the air suspension system, the vehicle will disable load leveling as required (suspension over- loaded, battery charge low, etc.). Load leveling will auto- matically resume as soon as system operation requirements are met. See your authorized dealer if syste...

  • Page 351

    Flashing, the highest flashing indicator lamp is the position the system is working to achieve. When lowering, if multiple indicators are flashing, the lowest solid indicator lamp is the position the system is working to achieve. Pushing the “up” button once will move the suspension one position hig...

  • Page 352

    • transport mode – no indicator lamps will be illumi- nated. Transport mode is disabled by driving the ve- hicle. • tire/jack mode – indicator lamps 3 and 6 will be illuminated. Tire/jack mode is disabled by driving the vehicle. • wheel alignment mode – indicator lamps 3 and 4 will be illuminated. W...

  • Page 353

    • normal ride height (nrh) – this is the standard position of the suspension and is meant for normal driving. • off-road (or) (raises the vehicle approximately 1 in (26 mm)) – this position is intended for off-roading use only where maximum ground clearance is required. To enter or, push the “up” bu...

  • Page 354

    Below 15 mph (24 km/h) the vehicle height will begin to lower. If the vehicle speed remains between 15 mph (24 km/h) and 25 mph (40 km/h) for greater than 60 seconds, or the vehicle speed exceeds 25 mph (40 km/h) the entry/exit change will be cancelled. To return to normal height mode, push the “up”...

  • Page 355

    Warning! (continued) injury or damage to the system, see your authorized dealer for service. Air suspension modes the air suspension system has multiple modes to protect the system in unique situations: aero mode to improve aerodynamics, the air suspension system has a feature which will put the veh...

  • Page 356

    Protection strategy in order to “protect” the air suspension system, the vehicle will disable load leveling as required (suspension over- loaded, battery charge low, etc.). Load leveling will auto- matically resume as soon as system operation requirements are met. See your authorized dealer if syste...

  • Page 357

    Pushing the “up” button once will move the suspension one position higher from the current position, assuming all conditions are met (i.E. Key in on/run position, engine running, speed below threshold, etc). The “up” button can be pushed multiple times, each push will raise the re- quested level by ...

  • Page 358

    Air suspension system (2500/3500 models) — if equipped description this air suspension system is a rear leveling ride height system. The main purpose of this system is to maintain the truck’s rear ride height level. There are two selectable heights that can be chosen based on your operating condi- t...

  • Page 359

    Note: • most 3500 models will not lower to alternate trailer height (ath) when unloaded. • refer to “trailer towing” in “starting and operating” for further information. Ignition off behavior for a predetermined amount of time after the ignition is off the air suspension may adjust to maintain a pro...

  • Page 360

    To know your instrument panel” or “uconnect settings” in “multimedia” if equipped with a touch screen radio for further information. Note: this mode is intended to be enabled with engine running. Protection strategy in order to “protect” the air suspension system, the vehicle will disable load level...

  • Page 361

    Axle locker system — power wagon models only (if equipped) this vehicle is equipped with electronically locking front and rear differentials. These differentials, when engaged, mechanically lock together the axle shafts forcing the wheels to spin at an equal rate. This allows the vehicle to maintain...

  • Page 362

    The locking axles are controlled by the axle locker switch. The switch has three positions: • axle unlock – the front and rear axles are unlocked • rear lock – the rear axle is locked • front/rear lock – the front and rear axles are locked under normal driving conditions, the switch should be left i...

  • Page 363

    Note: the axle lockers could be torque locked due to side to side loads on the axle. Driving slowly while turning the steering wheel from a left hand turn to a right hand turn or driving in reverse for a short distance may be required to release the torque lock and unlock the axles. To unlock the re...

  • Page 364

    Warning! (continued) enhances vehicle stability and assists in maintaining control of the vehicle. The system monitors vehicle speed and will attempt to reconnect the stabilizer bar at speeds over 18 mph (29 km/h). This is indicated by a flashing off road light and solid on road light. Once vehicle ...

  • Page 365

    The national forest service, bureau of land management, or local department of natural resources are a wealth of information and usually have maps with marked trails. Skid plates and underbody protection steel skid plates protect the major driveline components of the truck including the fuel tank, t...

  • Page 366

    And ice. Every surface has a different effect on your vehicle’s steering, handling and traction. Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture. Avoid sudden accelerations, turns or brak...

  • Page 367

    Stop, try turning your steering wheel no more than a ¼ turn quickly back and forth, while still applying throttle. This will allow the tires to get a fresh ⬙bite⬙ and help maintain your momentum. Caution! On icy or slippery roads, do not downshift at high engine rpms or vehicle speeds because engine...

  • Page 368

    Crossing obstacles (rocks and other high points) while driving off road, you will encounter many types of terrain. These varying types of terrain bring different types of obstacles. Before proceeding review the path ahead to determine the correct approach and your ability to safely recover the vehic...

  • Page 369

    Large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover. If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires. Use the removed dirt to fill the rut ahead of the turnout you just created. You should...

  • Page 370

    Hill climbing hill climbing requires good judgment and a good under- standing of your abilities and your vehicle’s limitations. Hills can cause serious problems. Some are just too steep to climb and should not be attempted. You should always feel confident with the vehicle and your abilities. You sh...

  • Page 371

    Is it a straight descent? Is there plenty of distance at the base of the hill to regain control if the vehicle descends too fast? If you feel confident in your ability to proceed then make sure you are in 4lo (low range) with the transmission in first gear (manually select first gear on automatic tr...

  • Page 372

    Driving through water extreme care should be taken crossing any type of water. Water crossings should be avoided if possible and only be attempted when necessary, in a safe responsible manner. You should only drive through areas which are designated and approved. You should tread lightly and avoid d...

  • Page 373

    Water depth, approach angle, and bottom condition. Murky or muddy water holes are where you want to hook up tow straps prior to entering. This makes for a faster, cleaner and easier vehicle recovery. If you are able to determine you can safely cross, than proceed using the low and slow method. Cauti...

  • Page 374

    Start high and lower it as required. Remember you must return the tires to normal air pressure before driving on road or at highway conditions. Be sure you have a way to return the tires to their normal on road air pressure. Caution! Reduced tire pressure increases the risk of tire damage and may ca...

  • Page 375

    Each shift. During this process, for additional traction, try turning your steering wheel quickly left and right no more than a ¼ turn. If you are stuck in mud, sand, or snow try spinning your tires during this process to clean the debris from the tread and improve the traction. You want to create a...

  • Page 376

    Warning! Never use tow straps with end hooks or link two straps with a clevis pin. These heavy metal objects could become projectiles if a strap breaks, which could cause severe injury. Never leave more than 2 to 3 feet (.6 to 1 meter) of slack in the strap. More slack than this greatly increases th...

  • Page 377

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect...

  • Page 378

    Driving and cornering, the limited-slip unit performs simi- larly to a conventional differential. On slippery surfaces, however, the differential delivers more of the driving effort to the rear wheel having the better traction. The limited-slip differential is especially helpful during slippery driv...

  • Page 379

    Caution! Be certain the anchor will withstand the load required to tension the wire rope. 3. Apply at least 500 lbs (227 kg) of tension to the rope while winding the rope. Always use care to ensure the rope does not pile up on one side of the drum and is neatly wound onto the drum. Caution! Wire rop...

  • Page 380

    Understanding the features of your winch winch components 378 starting and operating.

  • Page 381

    1. Motor: the winch motor is powered by the vehicle charging system and features a thermal protection switch that automatically stops motor function in the power-in direction if the motor gets too hot. 2. Remote socket: the remote socket allows the remote control to be attached to the control pack t...

  • Page 382

    Winch accessories the following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: wire rope, through use, will develop ⬙barbs⬙ which can slice skin. It is extremely important to wear protec- tive gloves while operating the winch or han...

  • Page 383

    Operating your winch warning! Failure to observe any of these warnings regarding proper winch usage may result in severe injury. • always use supplied hook strap to hold the hook when spooling wire rope in or out. • never use as a hoist. • never use to move persons. • never exceed winch or wire rope...

  • Page 384

    General information practice using your winch before you get stuck. Some key points to remember when using your winch are: • always take your time to assess the situation and plan your pull carefully. • always take your time when using a winch. • use the right equipment for the situation. • always w...

  • Page 385

    1. Inspect the winch, winch mount, and wire rope for damage. Do not use the winch if the mount is loose or rope shows excessive wear or damage. 2. Put on gloves. 3. Disengage the clutch to allow free spooling of the winch drum, rotate the clutch lever on the winch to disengage. Freespooling conserve...

  • Page 386

    4. Free the winch hook and attach the hook strap. Free the winch hook from its anchor point. Attach the hook strap to the hook (if not attached). 5. Pull the wire to the anchor point. Pull out enough wire rope to reach your anchor point. Be sure to keep a certain amount of tension on the wire as it ...

  • Page 387

    6. Secure to the anchor point. Once you have established your anchor point, secure the tree-trunk protector or choker-chain around the object. Caution! Always be certain the anchor you select will withstand the load. Note: how to choose an anchor point: a secure anchor is critical to winching operat...

  • Page 388

    7. Attach the clevis/d-shackle and tree trunk protector. Attach the shackle to the two ends of the strap or chain and through the hook loop, being careful not to over tighten (tighten and back-off 1/2 turn). 8. Lock the clutch. Lock the winch drum by rotating the clutch lever on the winch to engage....

  • Page 389

    11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure. 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope. Pulling wire rope under tension wire ...

  • Page 390

    In certain situations you may decide to throw a heavy blanket or similar object over the wire rope. A heavy blanket can absorb energy should the wire rope break. Place it on the wire rope midway between the winch and the anchor point. Do this before the wire rope is put under tension. Do not approac...

  • Page 391

    14. Begin winching. With the winching vehicles engine on and light tension already on the wire rope, begin winching slowly and steadily. Be sure that the wire rope is winding evenly and tightly around the spooling drum. For additional assistance, the winched vehicle can be slowly driven while being ...

  • Page 392

    16. Disconnect the wire rope, and disconnect from the anchor. 17. Rewind the wire rope. The person handling the wire rope should walk the rope in and not let it slide through the hand, control the winch at all times. Warning! To prevent serious injury, never put your fingers inside the hook area as ...

  • Page 393

    19. Disconnect the remote control. Disconnect the remote control cord from the control box and store in a clean and dry place. Winching operations are now complete. Put the cap on the solenoid plug-in. Note: always store the remote control in a protected, clean, dry area. Rigging techniques various ...

  • Page 394

    You to change your pulling direction while still allowing the wire rope to be at 90° to wind properly onto the spooling drum. Increasing pulling power in some cases, you may find yourself needing more pulling power. The use of snatch blocks increases mechanical advantage and that increases your pull...

  • Page 395

    If the steering icon is flashing, it indicates that the vehicle needs to be taken to the dealer for service. It is likely the vehicle has lost power steering assistance. If the steering icon is displayed and the “power steer- ing system over temp” message is displayed on the instrument cluster scree...

  • Page 396

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Power steering fluid check — 2500/3500 models checking the power steering flui...

  • Page 397

    Speed control when engaged, the speed control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the speed control system has been designed to shut down i...

  • Page 398

    To set a desired speed turn the speed control on. When the vehicle has reached the desired speed, push the set (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. Note: the vehicle should be traveling at a steady speed and on level ground before pushin...

  • Page 399

    • if the button is continually pushed, the set speed will continue to decrease until the button is released, then the new set speed will be established. Metric speed (km/h) • pushing the set (-) button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a...

  • Page 400

    Parksense rear park assist — if equipped the parksense rear park assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to “parksense system usage precautions” in this section for li...

  • Page 401

    The system will indicate a detected obstacle by showing a single arc in the left and/or right rear regions based on the object’s distance and location relative to the vehicle. If an object is detected in the left and/or right rear region, the display will show a single solid arc in the left and/or r...

  • Page 402

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: warning alerts rear distance (inches/cm) greater than 79 inches (200 cm) 79-45 inches (...

  • Page 403

    Arc none 4th solid 3rd solid 2nd flashing 1st flashing radio volume reduced no yes yes yes yes note: parksense will reduce the volume of the radio, if on, when the system is sounding an audio tone. Adjustable chime volume settings the rear chime volume settings are programmable. • the settings may b...

  • Page 404

    Service the parksense rear park assist system during vehicle start up, when the parksense rear park assist system has detected a faulted condition, the instru- ment cluster display will actuate a single chime, once per ignition cycle, and it will show the ⬙parksense un- available wipe rear sensors ⬙...

  • Page 405

    • clean the parksense sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The parksense system might not detect an obstacle behind the fascia/bumper, ...

  • Page 406

    Caution! • parksense is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • the vehicle mu...

  • Page 407

    The six parksense sensors, located in the front fascia/ bumper, monitor the area in front of the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 inches (30 cm) up to 47 inches (120 cm) from the front fascia/bumper in the horizontal direction,...

  • Page 408

    The vehicle is close to the obstacle when the display shows one flashing arc and sounds a continuous tone. The follow- ing chart shows the warning alert operation when the system is detecting an obstacle: warning alerts rear distance (inches/cm) greater than 79 inches (200 cm) 79-45 inches (200-115 ...

  • Page 409

    Adjustable chime volume settings the front and rear chime volume settings are program- mable. • the settings may be programmed through the uconnect system. Refer to “uconnect settings ” in “multimedia” for further information. Enabling and disabling front and/or rear parksense front parksense can be...

  • Page 410

    A faulted condition, the instrument cluster display will display a ⬙parksense unavailable wipe rear sen- sors ⬙, ⬙parksense unavailable wipe front sen- sors ⬙ or ⬙parksense unavailable service re- quired ⬙ pop up message for five seconds. After five seconds, a vehicle graphic will be displayed with ...

  • Page 411

    You turn front or rear parksense off, it remains off until you turn it on again, even if you cycle the ignition key. • when you move the gear selector to the reverse position and front or rear parksense is turned off, the instrument cluster display will show the ⬙front parksense off ⬙ or ⬙rear parks...

  • Page 412

    Warning! (continued) hitch ball will be much closer to the obstacle than the rear fascia when the loudspeaker sounds the con- tinuous tone. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the...

  • Page 413

    Whenever the rear view camera image is activated through the ⬙backup camera⬙ button in the ⬙controls⬙ menu, a display timer for the image is initiated. The image will continue to be displayed until the display timer exceeds 10 seconds and the vehicle speed is above 8 mph (13 km/h) or the touchscreen...

  • Page 414

    Warning! Drivers must be careful when backing up even when using the parkview rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstruc- tions, or blind spots before backing up. You are re- sponsible for the safety of your...

  • Page 415

    Refueling the vehicle — gas engine the fuel filler cap (gas cap) is located behind the fuel filler door, on the left side of the vehicle. Open the fuel door and remove the fuel cap by turning it counter-clockwise. Note: when removing the fuel filler cap, lay the cap tether in the hook, located on th...

  • Page 416

    Note: • when the fuel nozzle “clicks” or shuts off, the fuel tank is full. • tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened properly. The mil in the instrument cluster may turn on if the gas cap is not secured properly. Make sure that the g...

  • Page 417

    Gross axle weight rating (gawr) the gawr is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the gawr of each axle is not exceeded. Each axle gawr is determined by the components in the system with the lowest load carrying capacity (axl...

  • Page 418

    Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way you...

  • Page 419

    Warning! If the gross trailer weight is 5,000 lbs (2,267 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle. If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision. Gross combination weight ra...

  • Page 420

    Hitches are the most popular on the market today and they are commonly used to tow small and medium sized trailers. Weight-distributing hitch a weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue wei...

  • Page 421

    Recommended distribution hitch adjustment towing with 1500 air suspension 1. Set air suspension to normal ride height. No action is required if already in normal ride height. Note: the vehicle must remain in the engine run position with all doors closed while attaching a trailer for proper leveling ...

  • Page 422

    3. Under the instrument cluster or touch screen radio settings, enable jack mode. Jack mode will be canceled and procedure must be restarted if the vehicle is driven at speeds above 5mph (8 kmh). 4. Measure the height of the top of the front wheel opening on the fender to ground, this is height h1. ...

  • Page 423

    Towing with 2500/3500 air suspension 1. Position the truck to be ready to connect to the trailer (do not connect the trailer). Note: normal ride height (nrh) or alternate trailer height (ath) can be used. The vehicle must remain in the engine running position while attaching a trailer for proper lev...

  • Page 424

    4. Measure the height of the top of the front wheel opening on the fender to ground, this is height h2. 5. Install and adjust the tension in the weight distributing bars per the manufacturers’ recommendations so that the height of the front fender is approximately (h2-h1)/ 2+h1 (about 1/2 the differ...

  • Page 425

    Trailer hitch type and maximum trailer weight hitch type max. Trailer weight / max. Tongue weight class iii bumper hitch - 1500 model 5,000 lbs (2,268 kg) / 500 lbs (226 kg) class iv - 1500 model 11,000 lbs (4,989 kg) / 1100 lbs (498 kg) class v - 2500/ 3500 models 18,000 lbs (8,164 kg) / 1800 lbs (...

  • Page 426

    Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weight of the driver and all passengers. Note: remember that everything put into or on the...

  • Page 427

    Warning! (continued) • when hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, sus- pension, chassis structure or tires. • safety chains must always be used b...

  • Page 428

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible per- sonal injury. • an electronically actuated trailer brake controller is required when towing a trailer...

  • Page 429

    The user interface consists of the following: manual brake control lever slide the manual brake control lever to the left to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes. If the manual brake control lever is activated while the brake is also applied, the gr...

  • Page 430

    Towing conditions change. Changes to towing conditions include trailer load, vehicle load, road conditions and weather. Adjusting gain note: this should only be performed in a traffic free environment at speeds of approximately 20–25 mph (30–40 km/h). 1. Make sure the trailer brakes are in good work...

  • Page 431

    Repeat steps 8 and 9 until the gain setting is at a point just below trailer wheel lockup. If towing a heavier trailer, trailer wheel lockup may not be attainable even with the maximum gain setting of 10. Light electric heavy electric light eoh heavy eoh type of trailer brakes electric trailer brake...

  • Page 432

    Note: • an aftermarket controller may be available for use with trailers with air or electric-over-hydraulic trailer brake systems. To determine the type of brakes on your trailer and the availability of controllers, check with your trailer manufacturer or dealer. • removal of the itbm will cause er...

  • Page 433

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic transmission the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. ...

  • Page 434

    Frequent trailer towing. ⬙ refer to the “maintenance plan” for the proper maintenance intervals. Note: check the automatic transmission fluid level be- fore towing (6-speed automatic only). Tow/haul mode to reduce potential for automatic transmission overheat- ing, activate tow/haul mode when drivin...

  • Page 435

    Snowplow 1500 models only note: do not use this model vehicle for snowplow applications. Warning! Snowplows and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structure. The airbags could deplo...

  • Page 436

    Before plowing • check the hydraulic system for leaks and proper fluid level. • check the mounting bolts and nuts for proper tightness. • check the runners and cutting edge for excessive wear. The cutting edge should be ¼ to ½ in (6 cm to 1.2 cm) above ground in snow plowing position. • check that s...

  • Page 437

    Over the road operation with snowplow attached the blade restricts air flow to the radiator and causes the engine to operate at higher than normal temperatures. Therefore, when transporting the plow, angle the blade completely and position it as low as road or surface conditions permit. Do not excee...

  • Page 438

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models flat tow none not allowed see instructions • automatic transmission in park • manual transmission in gear (not in neutral) • t...

  • Page 439

    Recreational towing — two-wheel drive models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is al- lowed only if the rear wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dol...

  • Page 440

    Caution! (continued) damage. Tow with all four wheels either on the ground, or off the ground (using a vehicle trailer). • tow only in the forward direction. Towing this vehicle backwards can cause severe damage to the transfer case. • before recreational towing, the transfer case must be in neutral...

  • Page 441

    1. Bring the vehicle to a complete stop on level ground, with the engine running. Firmly apply the parking brake. 2. Shift the transmission to neutral. Note: if vehicle is equipped with air suspension, ensure the vehicle is set to normal ride height. 3. Press and hold the brake pedal. 4. Depress the...

  • Page 442

    Note: with electronic shift transfer case: • steps 2 through 4 are requirements that must be met before pushing the neutral (n) button, and must continue to be met until the shift has been completed. If any of these requirements are not met before pushing the neutral (n) button or are no longer met ...

  • Page 443

    Note: when shifting out of transfer case neutral (n), turning the engine off is not required, but may be helpful to avoid gear clash. With the 8-speed automatic transmis- sion, the engine must remain running, since turning the engine off will shift the transmission to park (and the transmission must...

  • Page 444

    Difference in the surface traction under the rear (driving) wheels. Warning! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have a collision. Accelerate slowly and care- fully when...

  • Page 445

    Warning! (continued) • failure to follow these warnings may result in inju- ries that are serious or fatal to you, your passengers, and others around you. Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bot...

  • Page 446

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect...

  • Page 447: In Case Of Emergency

    In case of emergency contents 䡵 hazard warning flashers . . . . . . . . . . . .447 䡵 assist and sos mirror — if equipped . . . .447 䡵 bulb replacement . . . . . . . . . . . . . . . . . . . .452 ▫ replacement bulbs . . . . . . . . . . . . . . . . . . . . .452 ▫ replacing exterior bulbs. . . . . . . ....

  • Page 448

    䡵 towing a disabled vehicle . . . . . . . . . . . .510 ▫ two-wheel drive models . . . . . . . . . . . . . . . . .512 ▫ four-wheel drive models . . . . . . . . . . . . . . . . .512 ▫ emergency tow hooks — if equipped. . . . . . . .513 䡵 enhanced accident response system (ears) . . . . . . . . . . . ....

  • Page 449

    Hazard warning flashers the hazard warning flasher switch is located on the upper switch bank just below the radio. Push the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Push t...

  • Page 450

    Warning! (continued) siriusxm guardian features and applications in this vehicle. Only use uconnect features and siriusxm guardian services when it is safe to do so. Failure to do so may result in an accident involving serious injury or death. Note: • your vehicle may be transmitting data as authori...

  • Page 451

    3. Once a connection between the vehicle and a sos operator is made, the sos call system may transmit the following important vehicle information to a sos op- erator: • indication that the occupant placed a sos call. • the vehicle brand. • the last known gps coordinates of the vehicle. 4. You should...

  • Page 452

    Warning! (continued) emergency services agent. All occupants should exit the vehicle immediately and move to a safe location. • never place anything on or near the vehicle’s oper- able network and gps antennas. You could prevent operable network and gps signal reception, which can prevent your vehic...

  • Page 453

    • an in-vehicle audio message will state “vehicle device requires service. Please contact your dealer.” warning! • ignoring the rearview mirror light could mean you will not have sos call services. If the rearview mirror light is illuminated, have an authorized dealer service the sos call system imm...

  • Page 454

    Warning! (continued) guardian services when it is safe to do so. Failure to do so may result in an accident involving serious injury or death. Note: • your vehicle may be transmitting data as authorized by the subscriber. • never place anything on or near the vehicle’s lte (voice/data) or 4g (data) ...

  • Page 455

    Exterior bulbs bulb number base quad headlamp – low beam h11ll base quad headlamp – high beam 9005ll front turn signal lamp (base quad headlamp) 3157na premium bi halogen pro- jector headlamp - low beam 9005sl+ premium bi halogen pro- jector headlamp - high beam 9005ll front turn signal lamp (premiu...

  • Page 456

    Replacing exterior bulbs base quad / premium bi-halogen: low beam headlamp, high beam headlamp, front park and turn — if equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the six plastic push-in fasteners that secure the upper radiator seal to the grille supp...

  • Page 457

    9. Remove the headlamp assembly. Grasp the outboard edge of the lamp and pull it straight forward to disen- gage the ball stud from the plastic grommet. 10. Disconnect the wiring harness connectors from the bulb socket. 11. Replace bulb(s) as necessary. Caution! • do not contaminate the bulb glass b...

  • Page 458

    Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. Rear tail/stop, turn signal and backup lamps 1. Remove the two screws that pass through the bed sheet metal. 2. Pull the outboard side of the...

  • Page 459

    Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. 6. Reverse the procedure to install the bulb and housing. Center high-mounted stoplamp (chmsl) with cargo lamp 1. Remove the two screws holdi...

  • Page 460

    Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • outside bulbs: cargo lamps • inside bulb: center high-mounted stop lamp 5. Reverse the procedure for installation of bulbs and housing. Cab...

  • Page 461

    2. Rotate the bulb socket ¼ turn and pull it from the lamp assembly. 3. Pull the bulb straight from it’s socket and replace. Removing bulb socket from clearance lamp removing the bulb from the bulb socket 7 in case of emergency 459.

  • Page 462

    Rear lamp bar id marker (dual rear wheels) — if equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets. 2. Turn the socket ¼ turn counterclockwise to access the bulb. 3. Pull the bulb straight out from the socket. 4. Reverse the procedure for installation of the bulbs a...

  • Page 463

    Fuses warning! • when replacing a blown fuse, always use an appro- priate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Do not place a fuse inside a circu...

  • Page 464

    Cavity cartridge fuse micro fuse description f03 60 amp yellow – rad fan – if equipped f05 40 amp green – compressor for air suspension – if equipped f06 40 amp green – antilock brakes/electronic stability control pump f07 40 amp green – starter solenoid f08 20 amp blue (1500 ld/cummins diesel) – em...

  • Page 465

    Cavity cartridge fuse micro fuse description f19 20 amp blue (1500 ld diesel) 30 amp pink (cum- mins diesel) – scr – if equipped f20 30 amp pink – passenger door module f21 30 amp pink – drive train control module f22 20 amp blue 30 amp pink (cum- mins diesel) – engine control module f23 30 amp pink...

  • Page 466

    Cavity cartridge fuse micro fuse description f34 30 amp pink – vehicle system interface module #2 – if equipped f35 30 amp pink – sunroof – if equipped f36 30 amp pink – rear defroster – if equipped f37 30 amp pink – cummins diesel fuel heater #2 – if equipped f38 30 amp pink – power inverter 115v a...

  • Page 467

    Cavity cartridge fuse micro fuse description f54 – 20 amp yellow adjustable pedals f56 – 15 amp blue additional diesel content – if equipped f57 – 20 amp yellow transmission f58 – 20 amp yellow spare fuse f59 – 10 amp red scr relay – if equipped f60 – 15 amp blue underhood lamp f61 – 10 amp red (150...

  • Page 468

    Cavity cartridge fuse micro fuse description f71 – 25 amp clear amplifier f72 – 10 amp red pcm – if equipped f73 – 20 amp yellow fuel transfer pump (hd only) – if equipped f74 – 20 amp yellow (gas engine & 1500 ld diesel) brake vacuum pump gas/diesel – if equipped f75 – 10 amp red coolant temperatur...

  • Page 469

    Cavity cartridge fuse micro fuse description f87 – 10 amp red air suspension – if equipped / trailer tow / steering column control module f88 – 15 amp blue instrument panel cluster f90/f91 – 20 amp yellow power outlet (rear seats) customer selectable f93 – 20 amp yellow cigar lighter f94 – 10 amp re...

  • Page 470

    Caution! • when installing the power distribution center cover, it is important to ensure the cover is properly posi- tioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • when replacing a blown fus...

  • Page 471

    If your vehicle is not equipped with a touchscreen, this feature can be activated through the instrument cluster display. Refer to “instrument cluster display” in “getting to know your instrument panel” for further information. Jack location the jack and jack tools are stored under the front passeng...

  • Page 472

    Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat. Release the tool bag straps from the jack and remove tools from bag. Jack and tools (1500 series) jack and tool bag 470 in case of emergency.

  • Page 473

    There are two ways to assemble the tools: assembled for spare tire lowering/raising caution! • the lug wrench can only be attached to extension 2. • when attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism ad-...

  • Page 474

    Assembled for jack operation warning! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may expe- rience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with f...

  • Page 475

    2. Rotate the lug wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. 3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. Rotating the lug wrench handle pulling the s...

  • Page 476

    4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. 5. Pull the retainer through the center of the wheel. Note: the winch mechanism is designed for use with the extension tubes only. Use of an air wrench or other power tools is not recommended and can...

  • Page 477

    Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Place the gear selector into park. On four-wheel drive vehicles, shift the transfer case to the 4l position. ...

  • Page 478

    Warning! (continued) • if working on or near a roadway, be extremely careful of motor traffic. • to assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. Caution! Do not attempt to raise the vehicle by jacking on locations other ...

  • Page 479

    3. Placement of the jack is critical: note: keep the jack and tools aligned with raising the vehicle. 4x2 series trucks front jacking location there is a jack location indicator on the rear portion of the lower control arm. Jack / extensions placement 1500 4x2 front jacking location indicator 7 in c...

  • Page 480

    When changing a front wheel, place the scissor jack under the rear portion of the lower control arm as shown below. 4x4 series trucks front jacking location there is a jack location indicator on the rear portion of the lower control arm. 4x2 front jacking location 4x4 front jacking location indicato...

  • Page 481

    When changing a front wheel, place the scissor jack under the rear portion of the lower control arm as shown below. Rear jacking location operate the jack using the extension with jack hook and the lug wrench. The extension tubes may be used but is not required. When changing a rear wheel, assemble ...

  • Page 482

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the lug nuts and pull the wheel off. Install the spare wheel and lug nuts with the cone shaped end of ...

  • Page 483

    Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. 1. Turn the wheel so that the valve stem is faci...

  • Page 484

    3. Attach the lug wrench to the extension tubes with the curved angle facing away from the vehicle. Insert the extension tubes through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube. 4. Rotate the lug wrench handle clockwise until the wheel is ...

  • Page 485

    Reinstalling the jack and tools (1500 series) 1. Tighten the jack all the way down by turning the jack turn-screw counterclockwise until the jack is snug. 2. Position the jack and tool bag. Make sure the lug wrench is under the jack near the jack turn-screw. 3. Secure the tool bag straps to the jack...

  • Page 486

    4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor. Note: ensure that the jack slides into the front hold down location. 5. Turn the wing bolt clockwise to ...

  • Page 487

    Jacking and tire changing 2500 and 3500 series trucks warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dange...

  • Page 488

    Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat. Remove the jack and tools from the bracket assembly. Turn the jack-turn-screw counterclockwise to release jack from bracket assembly. Wing bolt/jack and tool...

  • Page 489

    There are two ways to assemble the tools: assembled for spare tire lowering/raising caution! • the lug wrench can only be attached to extension 2. • when attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is (continued) caution! (continued) positioned corre...

  • Page 490

    Warning! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious inju...

  • Page 491

    2. Rotate the lug wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. 3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. Rotating the lug wrench handle pulling the s...

  • Page 492

    4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. 5. Pull the retainer through the center of the wheel. Note: the winch mechanism is designed for use with the extension tubes only. Use of an air wrench or other power tools is not recommended and can...

  • Page 493

    Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Place the gear selector into park. On four-wheel drive vehicles, shift the transfer case to the 4l position. ...

  • Page 494

    Warning! (continued) • if working on or near a roadway, be extremely careful of motor traffic. • to assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. Caution! Do not attempt to raise the vehicle by jacking on locations other ...

  • Page 495

    Note: if your vehicle is equipped with hub caps/wheel covers they must be removed before raising the vehicle off the ground. Refer to ”hub caps/wheel covers — if equipped” in this section. Lug wrench adapter lug wrench adapter and wrench 7 in case of emergency 493.

  • Page 496

    3. Placement of the jack is critical: front jacking location when changing the front wheel, assemble the jack driver to the jack and connect the jack driver to the extension tubes. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the...

  • Page 497

    Rear jacking location when changing a rear wheel, assemble the jack driver to the jack and connect the jack driver to the extension tubes. Place the jack under the axle between the spring and the shock absorber with the extension tubes extending to the rear. Connect the extension tubes and lug wrenc...

  • Page 498

    5. Remove the lug nuts and pull the wheel off. On single rear-wheel (srw) trucks, install the spare wheel and lug nuts with the cone shaped end of the wheel nuts toward the wheel. On 3500 dual rear-wheel models (drw) trucks, if the outer tire is being replaced then leave the inner wheel on the vehic...

  • Page 499

    Warning! A loose tire or jack thrown forward in a collision or hard stop, could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 7. Install the wheel center cap and remove the wheel blocks. Do not install chrome or aluminum wheel center cap...

  • Page 500

    2. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable and position it properly across the wheel opening. 3. Attach the lug wrench to the extension tubes with the curved angle facing away from the vehicle. Insert the extensions through the access hole bet...

  • Page 501

    4. Rotate the lug wrench handle clockwise until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip, or click three or four times. It cannot be overtight- ened. Push against the tire several times to ensure it is firmly in pl...

  • Page 502

    Turn-screw. Snap tools into bracket assembly clips. In- stall the jack into bracket assembly and turn the jack- turn-screw clockwise until jack is snug into bracket assembly. 3. Place the jack and tool bracket assembly in the storage position holding the jack by the jack turn-screw, slip the jack an...

  • Page 503

    4. Turn the wing bolt clockwise to secure to the floor pan. Reinstall the plastic cover. Hub caps/wheel covers — if equipped the hub caps must be removed before raising the vehicle off the ground. Caution! Use extreme caution when removing the front and rear center caps. Damage can occur to the cent...

  • Page 504

    Caution! (continued) • the rear hub caps on the dual rear wheel has two pull off notches. Make sure that the hook of the jack handle driver is located squarely in the cap notch before attempting to pull off. You must use the flat end of the lug wrench to pull off the wheel skins. Locate the hub cap ...

  • Page 505

    Warning! • take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You coul...

  • Page 506

    Jump starting procedure warning! Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Con...

  • Page 507

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery. 2. Disconnect the opposite end of the negative (-) jumper cable f...

  • Page 508

    To the radiator and aids in removing heat from the engine cooling system. Warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Neve...

  • Page 509

    6. Move the gear selector to the neutral position. 7. The vehicle may then be started in neutral. Center console gear selector — if equipped 1. Turn the engine off. 2. Firmly apply the parking brake. 3. Using a small screwdriver or similar tool, remove the gear selector override access cover (locate...

  • Page 510

    Manual park release — 8 speed transmission warning! Always secure your vehicle by fully applying the parking brake before activating the manual park re- lease. In addition, you should be seated in the driver’s seat with your foot firmly on the brake pedal when activating the manual park release. Act...

  • Page 511

    5. While holding the locking tab in the disengaged posi- tion, pull the tether strap to rotate the lever rearward, until it locks in place pointing towards the driver’s seat. Release the locking tab and verify that the manual park release lever is locked in the released position. 6. The vehicle is n...

  • Page 512

    Warning! (continued) injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. Caution! • racing the engine or spinning the wheel...

  • Page 513

    Towing condition wheels off the ground 2wd models 4wd models flat tow none if transmission is operable: • transmission in neutral • 30 mph (48 km/h) max speed • 15 miles (24 km) max distance (6–speed transmission) • 30 miles (48 km) max distance (8–speed transmission) see instructions in “recreation...

  • Page 514

    Caution! • do not use sling type equipment when towing. Vehicle damage may occur. • when securing the vehicle to a flat bed truck, do not attach to front or rear suspension components. Dam- age to your vehicle may result from improper towing. Two-wheel drive models the manufacturer recommends towing...

  • Page 515

    If flatbed equipment is not available, and the transfer case is operable, the vehicle may be towed (in the forward direction, with all wheels on the ground), if the transfer case is in neutral and the transmission is in park (for automatic transmissions) or in gear (not in neutral, for manual transm...

  • Page 516

    Enhanced accident response system (ears) this vehicle is equipped with an enhanced accident response system. Please refer to “occupant restraint systems” in “safety” for further information on the enhanced accident re- sponse system (ears) function. Event data recorder (edr) this vehicle is equipped...

  • Page 517: Servicing And Maintenance

    Servicing and maintenance contents 䡵 scheduled servicing . . . . . . . . . . . . . . . . .517 ▫ maintenance plan . . . . . . . . . . . . . . . . . . . . . .518 ▫ heavy duty use of the vehicle . . . . . . . . . . . .522 䡵 engine compartment . . . . . . . . . . . . . . . . .523 ▫ 3.6l engine . . . . ....

  • Page 518

    ▫ tire safety information . . . . . . . . . . . . . . . . . .558 ▫ tires — general information . . . . . . . . . . . . . .568 ▫ tire types . . . . . . . . . . . . . . . . . . . . . . . . . . . .574 ▫ spare tires — if equipped . . . . . . . . . . . . . . . .575 ▫ wheel and wheel trim care . . . . . ....

  • Page 519

    Scheduled servicing your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This ...

  • Page 520

    Severe duty all models note: change engine oil at 4,000 miles (6,500 km) or 350 hours of engine run time if the vehicle is operated in a dusty and off road environment or is operated predomi- nantly at idle, or only very low engine rpm’s. This type of vehicle use is considered severe duty. Once a mo...

  • Page 521

    Mileage or time passed (which- ever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 522

    Mileage or time passed (which- ever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 523

    Mileage or time passed (which- ever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 524

    Warning! (continued) • failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident. Heavy duty use of the vehicle change engine oil at 4,000 miles (6,500 km) or 350 hours of engine run time if...

  • Page 525

    Engine compartment 3.6l engine 1 — air cleaner filter 2 — engine oil dipstick 3 — engine oil fill 4 — brake fluid reservoir 5 — battery 6 — washer fluid reservoir 7 — power distribution center (fuses) 8 — coolant pressure cap 9 — engine coolant reservoir 8 servicing and maintenance 523.

  • Page 526

    5.7l engine 1 — air cleaner filter 7 — washer fluid reservoir 2 — automatic transmission dipstick (6-speed trans only) 8 — power distribution center (fuses) 3 — engine oil fill 9 — power steering fluid reservoir (2500/3500 models only) 4 — engine oil dipstick 10 — coolant pressure cap 5 — brake flui...

  • Page 527

    6.4l engine 1 — coolant pressure bottle 6 — battery 2 — transmission dipstick 7 — power distribution center (fuses) 3 — engine oil fill 8 — washer solvent 4 — engine oil dipstick 9 — power steering fluid reservoir 5 — brake fluid reservoir 10 — air cleaner filter 8 servicing and maintenance 525.

  • Page 528

    Checking oil level — gas engine to assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed up ...

  • Page 529

    Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Ref...

  • Page 530

    Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. Engine oil — gas engine change engine ...

  • Page 531

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american pe- troleum institute (api). The manu- facturer only recommends api cer- tified engine oils. This symbol certifies 0w-20, 5w-20, 0w-30, 5w-30 and 10w-30 engine oils. ...

  • Page 532

    Engine oil viscosity (sae grade) — 6.4l engine use mopar sae 0w-40 engine oil approved to fca mate- rial standard ms-12633 such as pennzoil ultra equivalent is recommended for all operating temperatures. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For i...

  • Page 533

    Engine air cleaner filter refer to the “maintenance plan” in this section for the proper maintenance intervals. Note: be sure to follow the “severe duty conditions” maintenance interval if applicable. Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in...

  • Page 534

    2. Lift the air cleaner cover to access the air cleaner filter. 3. Remove the air cleaner filter element from the housing assembly. 6.4l air cleaner filter cover 1 — clean air hose clamp 2 — spring clips open air cleaner filter assembly 1 — air cleaner cover 2 — air cleaner filter 532 servicing and ...

  • Page 535

    Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleaner filter inspection surface facing downward. 2. Install the air clea...

  • Page 536

    Warning! (continued) damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condition- ing components. Such damage...

  • Page 537

    The cabin air filter is located in the fresh air inlet behind the glove compartment. Perform the following procedure to replace the filter: 1. Open the glove compartment and remove all contents. 2. With the glove compartment door open, remove the glove compartment tension tether and tether clip by s...

  • Page 538

    4. Disengage the glove compartment door from its hinges by opening the glove compartment past the travel stop and pulling it toward you. 5. Remove the filter cover by pushing in on the finger tabs on each end of the filter cover. Glove compartment 1 — glove compartment travel stops 2 — glove compart...

  • Page 539

    6. Remove the cabin air filter by pulling it straight out of the housing. Finger tabs finger tab 8 servicing and maintenance 537.

  • Page 540

    7. Install the cabin air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, press on each end until you hear an audible click. Caution! The cabin air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly...

  • Page 541

    Note: ensure the glove compartment door hinges and glove compartment travel stops are fully engaged. 10. Reattach the glove compartment tension tether by inserting the tether clip in the glove compartment and sliding the clip away from the face of the glove compartment door. Front driveshaft lubrica...

  • Page 542

    The grease fitting is located at the rear of the front driveshaft, near the centering mechanism of double cardan joint. Refer to the “maintenance plan” for the proper maintenance intervals. Use mopar type ms-6560 (lithium- based grease), or equivalent. Accessory drive belt inspection warning! • do n...

  • Page 543

    Conditions that would require replacement: • rib chunking (one or more ribs has separated from belt body) • rib or belt wear • longitudinal belt cracking (cracks between two ribs) • belt slips • “groove jumping⬙ (belt does not maintain correct posi- tion on pulley) • belt broken (note: identify and ...

  • Page 544

    The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant, such as mopar lock cylinder lubricant directly into the lock cylinder. Windshield wiper blades clean the rubber edges of the wiper blades and the windsh...

  • Page 545

    2. To disengage the wiper blade from the wiper arm, flip up the locking tab. 3. Tilt the lower end of the wiper blade away from the arm and use one finger push the release tab toward the wiper arm. Windshield wiper arm 1 — wiper 2 — locking tab 3 — wiper arm wiper locking assembly 1 — wiper 2 — lock...

  • Page 546

    4. Slide the wiper blade down towards the base of the wiper arm. 5. With the wiper blade disengaged, remove the wiper blade from the wiper arm by holding the wiper arm with one hand and separating the wiper blade from the wiper arm with the other hand (move the wiper blade down toward the base of th...

  • Page 547

    3. Insert the receiver bracket on the wiper assembly into the hook on the tip of the arm through the opening in the wiper blade under the locking tab. 4. Slide the wiper blade up into the hook on the wiper arm until it is latched (engagement will be accompanied by an audible click). Fold down the la...

  • Page 548

    Caution! (continued) the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible dam...

  • Page 549

    Appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the a/c condenser (if equipped) or radiator for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the a/c condenser (if e...

  • Page 550

    Caution! (continued) be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (anti- freeze) is not recommended. Adding coolant your veh...

  • Page 551

    Hoat and oat coolant are mixed in an emergency, have a authorized dealer drain, flush, and refill with oat coolant (conforming to ms.90032) as soon as pos- sible. Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coo...

  • Page 552

    To check the coolant level: 1. Open the coolant reservoir. 2. Lift and remove the plastic dipstick from the reservoir neck. 3. Check the coolant level on the dipstick. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (an...

  • Page 553

    Checking coolant level — 6.4l engine the level of the coolant in the pressurized coolant bottle should be between the “min” and “max” range on the bottle when the engine is cold. The radiator normally remains completely full, so there is no need to remove the cap unless checking for coolant freeze p...

  • Page 554

    The correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions. Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “maintenanc...

  • Page 555

    Warning! (continued) in a tightly closed container. Keep the master cylin- der reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged brak- ing, resulting in...

  • Page 556

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check — eight-speed transmission the fluid level is preset at the factory and does not require adjustment ...

  • Page 557

    3. Run the engine at normal idle speed for at least 60 seconds, and leave the engine running for the rest of this procedure. 4. Fully apply the parking brake, and press the brake pedal. 5. Place the gear selector momentarily into each gear position (allowing time for the transmission to fully engage...

  • Page 558

    Note: to prevent dirt and water from entering the transmission after checking or replenishing fluid, make sure that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tub...

  • Page 559

    Note: the presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage. Limited-slip differ...

  • Page 560

    Hoisting a conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking locations. However, a floor jack or frame hoist must never be used on any other parts of the underbody. Caution! Never use a floor jack directly under the differential housing of a loaded...

  • Page 561

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 562

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ....Blank....ⴖ = passenger car tire based on european design standards, or lt = light truck tire based o...

  • Page 563

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions – the maximum speed corr...

  • Page 564

    Tire identification number (tin) the tin may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 565

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located be- hind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hour...

  • Page 566

    Tire loading and tire pressure note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure...

  • Page 567

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 568

    Steps for determining correct load limit— (1) locate the statement “the combined weight of occupants and cargo should never exceed xxx kg or xxx lbs.” on your vehicle’s placard. (2) determine the combined weight of the driver and passengers that will be riding in your vehicle. (3) subtract the combi...

  • Page 569

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them. 8 servicing and maintenance 567.

  • Page 570

    Tires — general information tire pressure proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Four primary areas are affected by improper tire pressure: • safety and vehicle stability • economy • tread wear • ride comfort safety warning! • improperly i...

  • Page 571

    Fuel economy underinflated tires will increase tire rolling resistance resulting in higher fuel consumption. Tread wear improper cold tire inflation pressures can cause abnormal wear patterns and reduced tread life, resulting in the need for earlier tire replacement. Ride comfort and vehicle stabili...

  • Page 572

    Pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire ...

  • Page 573

    Run flat tires — if equipped run flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the run flat mode. A run flat mode occurs when the tire inflation pressure is of/or below 14 psi...

  • Page 574

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be re- placed. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (1.6 mm). When t...

  • Page 575

    Warning! (continued) you could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement tires the tires on your new vehicle p...

  • Page 576

    Warning! (continued) • never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • failure to equip your vehicle wi...

  • Page 577

    Snow tires some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a “mountain/snowflake” symbol on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the origi- nal equipment tires. Use snow tires only in sets of...

  • Page 578

    Spare by looking at the spare tire description on the tire and loading information placard located on the driver’s side door opening or on the sidewall of the tire. Compact spare tire descriptions begin with the letter “t” or “s” preceding the size designation. Example: t145/80d18 103m. T, s = tempo...

  • Page 579

    Warning! Compact and collapsible spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to f...

  • Page 580

    Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral ph) soap and water to maintain their luster and to prevent corrosion. Wash wheels with the same soap solution recommended for the body of the vehicle. Yo...

  • Page 581

    Dark vapor chrome, black satin chrome, or low gloss clear coat wheels caution! If your vehicle is equipped with these specialty wheels, do not use wheel cleaners, abrasives, or polishing compounds. They will permanently damage this finish and such damage is not covered by the new vehicle limited war...

  • Page 582

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 583

    The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Directional tires — if equipped for the r/t package with 22” tires and wheels, the rotational direction of the tire must be ...

  • Page 584

    Dual rear wheels — if equipped the tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. Note: if your vehicle is equipped with a ti...

  • Page 585

    Caution! (continued) the truck. For example, if the spare is used to replace an outer rear tire it will have to be remounted on the rim so that the wheel is dished inward. That way the tread design of asymmetrical tires and the white writing of the owl tires will maintain proper posi- tion. Departme...

  • Page 586

    Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade c corresponds to a level of performance, which all pas- senger vehicle tires must meet under the federal motor vehicle safety standar...

  • Page 587

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 588

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8,274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 589

    To help maintain the appearance of your spray-on bedliner, follow the steps below: 1. Rinse your truck bed out with water to remove any loose dirt and debris. 2. Mix a mild soap or detergent with water with a soft cloth or brush. 3. Rinse bedliner with water. 4. Once dry, apply a small amount of mop...

  • Page 590

    Stain repel fabric cleaning procedure — if equipped stain repel seats may be cleaned in the following manner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar total clean, or a mild soa...

  • Page 591

    Caution! (continued) painted, or decorated surfaces of the interior may causepermanent damage. Wipe away immediately. • damage caused by these type of products may not be covered by your new vehicle limited warranty. Cleaning plastic instrument cluster lenses the lenses in front of the instruments i...

  • Page 592

    Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar glass cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or windows equipped with radio anten...

  • Page 593: Technical Specifications

    Technical specifications contents 䡵 identification data. . . . . . . . . . . . . . . . . . .593 ▫ vehicle identification number . . . . . . . . . . . . .593 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . . .593 ▫ hydraulic brake assist — 2500/3500 models only (except power wagon) . . . ....

  • Page 594

    ▫ maintenance . . . . . . . . . . . . . . . . . . . . . . . . . .602 䡵 fluid capacities . . . . . . . . . . . . . . . . . . . . . .603 䡵 fluids and lubricants . . . . . . . . . . . . . . . .604 ▫ engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .604 ▫ chassis . . . . . . . . . . . . ...

  • Page 595

    Identification data vehicle identification number the vehicle identification number (vin) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the vehicle frame and underbody as well as the automobile informa- tion disclosure label af...

  • Page 596

    Wheel and tire torque specifications proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly cali- brated torque wrench using a hi...

  • Page 597

    Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it half- way). After 25 mil...

  • Page 598

    Fuel requirements 3.6l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when using high-quality unleaded “regular” gasoline having an octane rating of 87 as specified by the (r+m)/2 method. The use of higher octane “premium” gaso- ...

  • Page 599

    6.4l engine do not use e-85 flex fuel or ethanol blends greater than 15% in this engine. This engines is designed to meet all emissions regulations and provide satis- factory fuel economy and performance when using high quality unleaded gaso- line having a posted octane number range of 87 to 89 as s...

  • Page 600

    Gasoline is recommended. Visit www.Toptiergas.Com for a list of top tier detergent gasoline retailers. Indiscriminate use of fuel system cleaning agents should be avoided. Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients. These can harm ...

  • Page 601

    Cng and lp fuel system modifications modifications that allow the engine to run on compressed natural gas (cng) or liquid propane (lp) may result in damage to the engine, emissions, and fuel system compo- nents. Problems that result from running cng or lp are not the responsibility of the manufactur...

  • Page 602

    Note: intentional tampering with the emissions control system can result in civil penalties being assessed against you. Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon mon- oxide poisoning: • do not inhale exhaust gase...

  • Page 603

    Warning! (continued) materials lit or products that can cause spark in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use e-85 as a cleaning agent and never use it near an open flame. Fuel requirements if your vehicle is e-85 compatible, it will oper...

  • Page 604

    Starting the characteristics of e-85 fuel make it unsuitable for use when ambient temperatures fall below 0°f (-18°c). In the range of 0°f (-18°c) to 32°f (0°c), an increase in the time it takes for your engine to start may be experienced, and a deterioration in driveability (sags and/or hesitations...

  • Page 605

    Fluid capacities u.S. Metric fuel (approximate) 1500 regular cab shortbed/crew quad cab models 26 gallons 98 liters 1500 regular cab longbed/crew quad cab models (optional) 32 gallons 121 liters 2500/3500 shortbed models 31 gallons 117 liters 2500/3500 longbed models 32 gallons 121 liters engine oil...

  • Page 606

    U.S. Metric 5.7l engine – 2500/3500 models (we recommend you use mopar antifreeze/coolant 10 year/150,000 mile formula that meets the re- quirements of fca material standard ms.90032.) 18.3 quarts 17.3 liters 6.4 liter engine – 2500/3500 models (we recommend you use mopar antifreeze/coolant 10 year/...

  • Page 607

    Component fluid, lubricant, or genuine part engine oil – 5.7l engine we recommend you use api certified sae 5w-20 engine oil, meeting the requirements of fca material standard ms-6395 such as mopar, pennzoil, and shell helix. Refer to your engine oil filler cap for correct sae grade. Engine oil – 6....

  • Page 608

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine dam- age and may decrease corrosion protection. Organic additive technology (oat) engine coolant is differ- ent and should not be mixed with hyb...

  • Page 609

    Chassis component fluid, lubricant, or genuine part automatic transmission – eight-speed automatic use only mopar zf 8&9 speed atf automatic transmis- sion fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmis- sion. Automatic transmission – s...

  • Page 610

    Component fluid, lubricant, or genuine part front and rear axle – 2500/3500 models we recommend you use sae 75w-85 hd ram gl-5 synthetic axle lubricant. Limited slip additive is not required for limited-slip rear axles. Brake master cylinder we recommend you use mopar dot 3. If dot 3 brake fluid is ...

  • Page 611: Multimedia

    Multimedia contents 䡵 uconnect radios . . . . . . . . . . . . . . . . . . . .611 䡵 personalized menu bar . . . . . . . . . . . . . . .611 䡵 cybersecurity . . . . . . . . . . . . . . . . . . . . . . . .612 䡵 uconnect settings . . . . . . . . . . . . . . . . . . .613 ▫ customer programmable features —...

  • Page 612

    ▫ register (4c nav) . . . . . . . . . . . . . . . . . . . . . .668 ▫ mobile app (4c nav) . . . . . . . . . . . . . . . . . . .668 ▫ siriusxm travel link (4c nav). . . . . . . . . . . . .669 ▫ apple carplay — if equipped. . . . . . . . . . . . . .669 ▫ android auto — if equipped . . . . . . . . . . ....

  • Page 613

    Uconnect radios for detailed information about your uconnect radio, refer to your uconnect owner’s manual supplement. Note: uconnect screen images are for illustration pur- poses only and may not reflect exact software for your vehicle. Personalized menu bar the uconnect features and services in the...

  • Page 614

    Cybersecurity your vehicle may be a connected vehicle and may be equipped with both wired and wireless networks. These networks allow your vehicle to send and receive informa- tion. This information allows systems and features in your vehicle to function properly. Your vehicle may be equipped with c...

  • Page 615

    Note: • fca us llc or your dealer may contact you directly regarding software updates. • to help further improve vehicle security and minimize the potential risk of a security breach, vehicle owners should: • routinely check www.Driveuconnect.Com/software- update to learn about available uconnect so...

  • Page 616

    Uconnect 3 buttons on the touchscreen and buttons on the faceplate 1 — uconnect buttons on the touchscreen 2 — uconnect buttons on the faceplate uconnect 4c/4c nav buttons on the touchscreen and buttons on the faceplate 1 — uconnect buttons on the touchscreen 2 — uconnect buttons on the faceplate 61...

  • Page 617

    Customer programmable features — uconnect 3 personal settings push the more or settings button on the faceplate, then press the “settings” button on the touchscreen (if equipped) to display the settings menu screen. In this mode the uconnect system allows you to access program- mable features that m...

  • Page 618

    Display after pressing the “display” button on the touchscreen, the following settings will be available. Setting name selectable options display mode auto manual set language english, français, español touchscreen beep on off fuel saver display on off note: the “fuel saver display” feature will all...

  • Page 619

    Voice after pressing the “voice” button on the touchscreen, the following settings will be available: setting name selectable options voice response length brief detailed show command list always with help never clock & date after pressing the “clock & date” button on the touch- screen, the followin...

  • Page 620

    Safety/assistance after pressing the “safety/assistance” button on the touchscreen, the following settings will be available: setting name selectable options parksense — if equipped sound only sounds and display note: the parksense system will scan for objects behind the vehicle when the transmissio...

  • Page 621

    Setting name selectable options note: your vehicle may be equipped with the parkview rear back up camera active guidelines that allows you to see ac- tive guidelines over the parkview back up camera display whenever the gear selector is put into reverse. The im- age will be displayed on the radio to...

  • Page 622

    Setting name selectable options hill start assist — if equipped note: when the “hill start assist” feature is selected, the hill start assist (hsa) system becomes active. Lights after pressing the “lights” button on the touchscreen, the following settings will be available: setting name selectable o...

  • Page 623

    Setting name selectable options equipped flash lights with lock on off note: when the “flash lights with lock” feature is selected, the exterior lights will flash when the doors are locked or un- locked with the key fob. This feature may be selected with or without the sound horn on lock feature sel...

  • Page 624

    Setting name selectable options sound horn with lock off 1st press 2nd press remote door unlock all driver note: the “remote door unlock” feature will allow you to program your remote door locks to open “all doors” or only the “driver door” with the first push of the key fob or grabbing the passive ...

  • Page 625

    Setting name selectable options note: the “passive entry” feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons. It automatically unlocks the doors when the outside door handle is grabbed. Flash lights with lock on off note: when the “f...

  • Page 626

    Engine off options after pressing the “engine off options” button on the touchscreen, the following settings will be available: setting name selectable options easy exit seats — if equipped headlight off delay 0 sec 30 sec 60 sec 90 sec engine off power delay 0 sec 45 sec 5 min 10 min setting name s...

  • Page 627

    Setting name selectable options auto entry/exit suspension on off note: when the “auto entry/exit suspension” feature is selected, the vehicle automatically lowers from ride height posi- tion when vehicle shifted to park for easy entry/exit. Display suspension messages all warning only automatic aer...

  • Page 628

    Setting name selectable options wheel alignment mode note: the “wheel alignment mode” feature prevents auto leveling of the air suspension while performing a wheel align- ment service. Before performing a wheel alignment, this mode must be enabled. Refer to your authorized dealer for further informa...

  • Page 629

    Setting name selectable options note: the “balance/fade” feature allows you to adjust the balance and fade settings. Press and drag the speaker icon or use the arrows to adjust, tap the “c” icon to readjust to the center. Equalizer + – note: when in the “equalizer” display you may adjust the bass, m...

  • Page 630

    Setting name selectable options loudness — if equipped on off note: the “loudness” feature improves sound quality at lower volumes. Compass settings — if equipped after pressing the “compass settings” button on the touchscreen, the following settings will be available: setting name selectable option...

  • Page 631

    Setting name selectable options perform compass calibration on off note: press the “calibration” button on the touchscreen to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass. When the vehicle is new, the compass may appear erratic until ...

  • Page 632

    Phone/bluetooth after pressing the “phone/bluetooth” button on the touch- screen, the following settings will be available: setting name selectable options paired phones list of paired phones note: the “paired phones” feature shows which phones are paired to the phone/bluetooth system. For further i...

  • Page 633

    Setting name selectable options subscription info sirius id note: new vehicle purchasers or lessees will receive a free limited time subscription to siriusxm satellite radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the subscrip...

  • Page 634

    Clear personal data after pressing the “clear personal data settings” button on the touchscreen, the following settings will be available: setting name selectable options clear personal data yes cancel note: when this feature is selected it will remove all personal data including bluetooth devices a...

  • Page 635

    Customer programmable features — uconnect 4c/4c nav personal settings press the “apps” button on the touchscreen then press the “settings” button on the touchscreen to display the settings menu screen. In this mode the uconnect system allows you to access programmable features that may be equipped s...

  • Page 636

    Display after pressing the “display” button on the touchscreen, the following settings will be available: setting name selectable options display mode day night auto note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the di...

  • Page 637

    Setting name selectable options set theme pre-configured themes set language english, français, español touchscreen beep navigation turn-by-turn in cluster — if equipped controls screen time-out — if equipped fuel saver display — if equipped units — if equipped after pressing “units” on the touchscr...

  • Page 638

    Voice after pressing the “voice” button on the touchscreen, the following settings will be available: setting name selectable options voice response length brief detailed show command list always with help never clock after pressing the “clock” button on the touchscreen, the following settings will ...

  • Page 639

    Safety & driving assistance after pressing the “safety & driving assistance” button on the touchscreen, the following settings will be available: setting name selectable options parksense sound only sound and display note: the rear park assist system will scan for objects behind the vehicle when the...

  • Page 640

    Setting name selectable options parkview backup camera note: your vehicle may be equipped with the parkview rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is put into reverse. The image will be displayed on the radio ...

  • Page 641

    Setting name selectable options rain sensing auto wipers — if equipped on off note: when the “rain sensing auto wipers” feature is selected, the system will automatically activate the windshield wip- ers if it senses moisture on the windshield. Hill start assist — if equipped on off setting name sel...

  • Page 642

    Lights after pressing the “lights” button on the touchscreen, the following settings will be available: setting name selectable options headlight off delay + – note: when the “headlight off delay” feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 second...

  • Page 643

    Setting name selectable options auto dim high beams — if equipped note: when the “auto dim high beams” feature is selected, the high beam headlights will deactivate automatically under certain conditions. Flash lights with lock note: when the “flash lights with lock” feature is selected, the exterio...

  • Page 644

    Setting name selectable options auto unlock on exit note: when the “auto unlock on exit” feature is selected, all doors will unlock when the vehicle is stopped and the trans- mission is in the park or neutral position and the driver’s door is opened. Flash lights with lock note: when the “flash ligh...

  • Page 645

    Setting name selectable options • if the vehicle is programmed “1st press of key fob unlocks: all doors”, all doors will unlock no matter which passive entry equipped door handle is grasped. If “1st press of key fob unlocks: driver door” is programmed, only the driver’s door will unlock when the dri...

  • Page 646

    Auto comfort systems — if equipped after pressing the “auto-on comfort” button on the touchscreen, the following settings will be available: setting name selectable options auto-on driver heated/ ventilated seat & steering wheel with vehicle start — if equipped off remote start all starts note: when...

  • Page 647

    Setting name selectable options engine off power delay + – note: when the “engine off power delay” feature is selected, the power window switches, radio, uconnect phone system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to ten minutes after the igni- tion ...

  • Page 648

    Setting name selectable options flash lights with lower note: when the “flash lights with lower” feature is selected, the front and rear turn signals will flash when the key fob remote lower button is pressed twice. This feature may be selected with or without the sound horn on lower feature selecte...

  • Page 649

    Setting name selectable options wheel alignment mode note: before performing a wheel alignment, the “wheel alignment mode” must be enabled. Refer to your authorized dealer for further information. Trailer brake after pressing the “trailer brake” button on the touch- screen, the following settings wi...

  • Page 650

    Audio after pressing the “audio” button on the touchscreen, the following settings will be available: setting name selectable options balance/fade speaker icon (arrow buttons) c note: the “balance/fade” feature allows you to adjust the balance and fade settings. Press and drag the speaker icon or us...

  • Page 651

    Setting name selectable options aux volume offset — if equipped on off note: the “aux volume offset” feature provides the ability to tune the audio level for portable devices connected through the aux input. Phone settings after pressing the “phone settings” button on the touch- screen, the followin...

  • Page 652

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be available: setting name selectable options tune start on off note: the “tune start” feature begins playing the current song from the beginning when you tune to a music channel...

  • Page 653

    Setting name selectable options subscription info sirius id note: new vehicle purchasers or lessees will receive a free limited time subscription to siriusxm satellite radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the subscrip...

  • Page 654

    Clear personal data after pressing the “clear personal data” button on the touchscreen, the following settings will be available: setting name selectable options clear personal data ok cancel note: when the “clear personal data” feature is selected it will remove all personal data including bluetoot...

  • Page 655

    Steering wheel audio controls — if equipped the remote sound system controls are located on the back surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push-button in the center. Pushing the top of the switch will incre...

  • Page 656

    If you push the switch up or down twice, it plays the second track. If you push the switch up or down three times, it will play the third, etc. Ipod/usb/mp3 control — if equipped located inside the center console upper lid, this feature allows an ipod or external usb device to be plugged into the us...

  • Page 657

    Not harmful to the radio. If your radio performance does not satisfactorily “clear” by the repositioning of the an- tenna, it is recommended that the radio volume be turned down or off during mobile phone operation when not using uconnect (if equipped). Regulatory and safety information usa/canada e...

  • Page 658

    Note: • this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment gener- ates, uses and...

  • Page 659

    Get started all you need to control your uconnect system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing instruc- tions. Uconnect 3 uconnect 4c/4c nav 10 multimedia 657.

  • Page 660

    2. Reduce background noise. Wind noise and passenger conversations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is located in the head- liner and aimed at the driver. 4. Each time you give a voice command,...

  • Page 661

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect system. Push the vr button . After the beep, say: • “cancel” to stop a current voice session • “help” to hear a list of suggested voice commands • “repeat” to listen to the system prompts again no...

  • Page 662

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio stations you would like to hear. (subscrip- tion or included siriusxm satellite radio trial required.) push the vr button . After the beep, say: • “ tune to ninety-five-point-five fm” • “ tune to satellite channel hits 1” ...

  • Page 663

    Media uconnect offers connections via usb, bluetooth and auxil- iary ports (if equipped). Voice operation is only available for connected usb and aux devices. (remote cd player optional and not available on all vehicles.) uconnect 3 uconnect 4c/4c nav 10 multimedia 661.

  • Page 664

    Push the vr button . After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artist. • “ change source to bluetooth” • “ change source to aux” • “ change source to usb” • “ play artist beethoven”; “ play album greatest hits”; “ play song moon...

  • Page 665

    Phone making and answering hands-free phone calls is easy with uconnect. When the phonebook button is illuminated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Uconnect 3 uconnect 4c/4c nav 10 multimedia 663.

  • Page 666

    Push the phone button . After the beep, say one of the following commands: • “ call john smith” • “ dial 123-456-7890 and follow the system prompts” • “ redial (call previous outgoing phone number)” • “ call back (call previous incoming phone number)” tip: when providing a voice command, push the ph...

  • Page 667

    Climate (4c/4c nav) too hot? Too cold? Adjust vehicle temperatures hands-free and keep everyone comfortable while you keep moving ahead. (if vehicle is equipped with climate control.) push the vr button . After the beep, say one of the following commands: • “ set driver temperature to 70 degrees” uc...

  • Page 668

    • “ set passenger temperature to 70 degrees” tip: voice command for climate may only be used to adjust the interior temperature of your vehicle. Voice command will not work to adjust the heated seats or steering wheel if equipped. Navigation (4c nav) the uconnect navigation feature helps you save ti...

  • Page 669

    Siriusxm guardian (4c nav) — if equipped caution! Some siriusxm guardian services, including sos call and roadside assistance call will not work without an operable lte (voice/data) or 3g or 4g (data) net- work connection compatible with your device. Note: your vehicle may be transmitting data as au...

  • Page 670

    Vehicle health reports** vehicle health alert** performance pages plus** **if vehicle is equipped. Register (4c nav) to unlock the full potential of siriusxm guardian in your vehicle, you must activate your siriusxm guardian ser- vices. 1. Press the apps icon on the bottom of your in-vehicle touchsc...

  • Page 671

    • press the location button on the navigation bar at the bottom of the app to bring up a map to locate your vehicle or send a location to your vehicle’s navigation system. • press the settings button in the upper left corner of the app to bring up app settings and access the assist call centers. Not...

  • Page 672

    “phone” icon on the main menu bar to begin apple carplay. Press and hold the vr button on the steering wheel, or press and hold the “home” button within apple carplay, to activate siri, which recognizes natural voice commands to use a list of your iphone’s features: • phone • music • messages • maps...

  • Page 673

    Android auto — if equipped android auto allows you to use your voice to interact with android’s best-in-class speech technology through your vehicle’s voice recognition system, and use your smart- phone’s data plan to project your android powered smart- phone and a number of its apps onto your uconn...

  • Page 674

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 675

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 677: Customer Assistance

    Customer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . .676 ▫ prepare for the appointment . . . . . . . . . . . . . .676 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . .676 ▫ be reasonable with requests . . . ...

  • Page 678

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 679

    Any communication to the manufacturer’s customer center should include the following information: • owner’s name and address • owner’s telephone number (home and office) • authorized dealer name • vehicle identification number (vin) • vehicle delivery date and mileage fca us llc customer center p.O....

  • Page 680

    To a tdd or a conventional teletypewriter (tty) in the united states, can communicate with the manufacturer by dialing 1-800-380-chry. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by bell canada. For tty teletypewriter users, di...

  • Page 681

    Warranty information see the warranty information booklet for the terms and provisions of fca us llc warranties applicable to this vehicle and market. Mopar parts mopar fluids, lubricants, parts, and accessories are avail- able from an authorized dealer. They are recommended for your vehicle in orde...

  • Page 682

    Service manuals these comprehensive service manuals provide the infor- mation that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintain- ing, servicing, and repairing fca us llc vehicles. A complete working knowledge of the vehicle, system, and/or compo...

  • Page 683: Index

    Index 12.

  • Page 684

    Adding engine coolant (antifreeze) . . . . . . . . . . . . .548 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .413 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . .597 adjust down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47, 49 forwar...

  • Page 685

    Fluid level check . . . . . . . . . . . . . . . . . . . . .553, 554 fluid type . . . . . . . . . . . . . . . . . . . . . . . . . .553, 607 shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . .306, 315 special additives . . . . . . . . . . . . . . . . . . . . . . . . .553 automatic transmi...

  • Page 686

    Child restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . .252 child restraints booster seats . . . . . . . . . . . . . . . . . . . . . . . . . . . .256 child restraints . . . . . . . . . . . . . . . . . . . . . . . . .252 child seat installation . . . . . . . . . . . . . . . . . .268, 2...

  • Page 687

    Disposal antifreeze (engine coolant) . . . . . . . . . . . . . . . . .549 door ajar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 door ajar light. . . . . . . . . . . . . . . . . . . . . . . . . . . .192 door locks, automatic . . . . . . . . . . . . . . . . . . . . . . .42 door ...

  • Page 688

    Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 engine oil viscosity . . . . . . . . . . . . . . . . . . . . .529, 530 engine oil viscosity chart . . . . . . . . . . . . . . . . . . . .529 enhanced accident response feature . . . . . . . . .250, 514 entry system, illuminate...

  • Page 689

    Materials added . . . . . . . . . . . . . . . . . . . . . . . . .597 methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .598 octane rating . . . . . . . . . . . . . . . . . . . . . . . .596, 604 requirements . . . . . . . . . . . . . . . . . . . . . . . .596, 603 tank capacity . . . ...

  • Page 690

    Ignition key removal . . . . . . . . . . . . . . . . . . . . . . . .28 illuminated entry . . . . . . . . . . . . . . . . . . . . . . . . . . .83 immobilizer (sentry key) . . . . . . . . . . . . . . . . . . . . . .33 inside rearview mirror . . . . . . . . . . . . . . . . .64, 65, 447 instrument clust...

  • Page 691

    Daytime running . . . . . . . . . . . . . . . . . . . . . . . . .74 engine temperature warning . . . . . . . . . . . . . . . .191 exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .281 fog . . . . . . . . . . . . . . . . . . . . . . . . . . . .78, 197, 455 four-wheel drive indicat...

  • Page 692

    Memory seats and radio . . . . . . . . . . . . . . . . . . . . .44 methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .598 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 electric powered . . . . . . . . . . . . . . . . . . . . . . . . . .67 heated ....

  • Page 693

    Passive entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 pedals, adjustable . . . . . . . . . . . . . . . . . . . . . . . . . . .62 personalized menu bar . . . . . . . . . . . . . . . . . . . . . .611 personal settings . . . . . . . . . . . . . . . . . . . . . . . . . . .182 pets ...

  • Page 694

    Programming additional key fobs . . . . . . . . . .27, 34 remote sound system (radio) controls . . . . . . . . . . .653 remote starting exit remote start mode . . . . . . . . . . . . . . . . . . . . .32 uconnect customer programmable features . .623, 644 uconnect settings . . . . . . . . . . . . . ....

  • Page 695

    Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44, 49 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 rear folding . . . . . . . . . . . . . . . . . . . . . . . .44, 55, 56 reclining rear . . . . . . . . . . . . . . . . . . . . . . . . . . .46 seatback rele...

  • Page 696

    Steering wheel audio controls . . . . . . . . . . . . . . . . .653 steering wheel mounted sound system controls . . . .653 storage compartment, center seat . . . . . . . . . . . . . .123 storage, vehicle . . . . . . . . . . . . . . . . . . . . . . . .105, 584 storing your vehicle . . . . . . . . . ....

  • Page 697

    Tonneau cover . . . . . . . . . . . . . . . . . . . . . . . . . . . .585 tonneau cover cleaning . . . . . . . . . . . . . . . . . . . . .585 to open hood . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 torque converter clutch . . . . . . . . . . . . . . . . . .315, 323 towing . . . . . . ...

  • Page 698

    Universal garage door opener (homelink) programming homelink . . . . . . . . . . . . .115, 117, 118 unleaded gasoline . . . . . . . . . . . . . . . . . . . . . . . . .596 untwisting procedure, seat belt . . . . . . . . . . . . . . . .229 utility rails, rear cargo area . . . . . . . . . . . . . . . ....

  • Page 699

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 700

    Second edition printed in the u.S.A. ©2017 fca us llc. All rights reserved. Ram is a registered trademark of fca us llc. 18ds-126-ab o w n e r ’ s m a n u a l 2 0 1 8 1 5 0 0 / 2 5 0 0 / 3 5 0 0 r a m t r u c k stick with the specialists ® ram truck 1500/2500/3500 2018.