Operation manual notice d’emploi bedienungsanleitung p-7654-564 qxpdqxdoc 4/06 © 2006 by c.E. Studio-2 s.L. - spain (eec) http://www.Ramaudio.Com e-mail: support@ramaudio.Com professional power amplifiers s series 1500-2000-3000-4000-6000 3004-4004-4044-6004-6044.
Warning: the exclamation point inside an equilateral triangle indicates the existen- ce of internal components whose substi- tution may affect safety. The lightning and arrowhead symbol warns about the presence of uninsula- ted dangerous voltage. To avoid fire or electrocution risk do not expose the...
0 safety precautions 1 general information 1.1 introduction 1.2 main characteristics 2 controls: where and what? 2.1 front panel 2.2 rear panel 3 installation and operation 3.1 connections 3.1.1 dual channel mode 3.1.2 link channel mode 3.1.3 bridge channel mode 3.2 configuration 3.3 troubleshooting...
The s series power amps is ram audio's response to our discerning clients' needs for a series of powerful, compact, versatile and rugged ampli- fiers characterised by no-compromise electronic and mechanical specifica- tions. The s series range offers the bonus of optional add-on modules that extend ...
Lokalisierung der funktionen see figure signal attenuation level control knobs: permit independent control of each channel’s attenuation (21 steps). Signal: this led indicates pre- sence of signal at the inputs. Temp: this led shows temperatu- re protection is active. Pms: led indicating pms in oper...
See figure signal input: female neutrik ® xlr connectors for the amplifier’s signal input. Signal link: (2 channels models only) male neutrik ® xlr connectors for daisy chaining input signal to other amplifiers (parallel connected to female input connectors). Link / dual switch: in link mode you can...
The power switch must always be on the “off” position before plugging the amp to a properly earthed mains soc- ket (220-240v ac / 110v-120v ac). The input signal fed to the amplifier can be either balanced or un-balanced. The drawing below describes both ways to wire an xlr connector for the purpose...
Installation and operation installation et mise en service the amplifier can operate on three diffe- rent configurations: dual, link or bridge. The connections for the three modes are different. See figure - switch “off” the amp. - set the mode switch on the rear panel to “dual”. - select the chosen...
3 4 dual channel 2 channel models 2 channel models 8 5 link inputs bridge mode 2 channel models.
3 4 dual channel 4 channel models 4 channel models 4 channel models 5 link inputs bridge mode bridge + dual mode 3 channels mode 9.
The amplifier has an ensemble of mini- dips on the back panel, which allow for the following configurations: the high- pass subsonic filter, the icl deactivation and the bridge mode. All these configu- rations can be cross-set in any way, independently from the others. The basic configuration possib...
In the event of incorrect connection or misfunctioning, the amp will activate one or more of its led to warn about the problem. Correct function: sgnl lights to indi- cate signal presence. Icl: the intelligent clip limiter is ope- rating (see page 10). No signal: no input signal is reaching the amp....
This is a complete set of protections that monitors the main amp parameters (load status, signal input, temperature, current, etc.) in order to draw from the power supply only the precise amount of current required to maintain safe operation during hazardous or extreme working conditions. This syste...
4.2 data 4.2 données techniques 4.2 technische daten technical specifications spécifications technische spezifikationen 13 technical specifications s-1500 s-2000 s-3000 s-4000 s-6000 s-3004 s-4004 s-4044 s-6004 s-6044 output power 1khz, 1.0% thd+n @ 2 Ω 2x 880 w 2x 1190 w 2x 1570 w 2x 1950 w 2x 2950...
Manufactured in the eec by c.E. Studio-2 s.L. Pol. Ind. La lloma - c/sierra perenxisa nº28 46960 aldaya - valencia - spain phone: +34 96 127 30 54 fax: +34 96 127 30 56 http://www.Ramaudio.Com e-mail: support@ramaudio.Com.
