1. DL manuals
  2. RAM
  3. Automobile
  4. 2011 Ram Truck Chassis Cab
  5. Owner's Manual

RAM 2011 Ram Truck Chassis Cab Owner's Manual

Other manuals for 2011 Ram Truck Chassis Cab: Owner's Manual
Manual is about: Chassis cab

Summary of 2011 Ram Truck Chassis Cab

  • Page 1

    C h a s s i s c a b chrysler group llc o w n e r ’ s m a n u a l 2 0 1 1 2 0 1 1 r a m t r u c k c h a s s is c a b 11dd43-126-ac second edition printed in u.S.A. Ram truck.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 4 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 6 䡵 van conversions/campers . . . . . . . . . . . . . . . . . 6 䡵 vehicle identifi...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Introduction 5.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 9

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Vehicle identification number 1 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ wireless ignition node (win) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 12 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ removing key fob f...

  • Page 12

    ▫ remote open window feature — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 24 ▫ using the panic alarm . . . . . . . . . . . . . . . . . 24 ▫ programming additional transmitters . . . . . . 24 ▫ transmitter battery replacement . . . . . . . . . . 25 ▫ general information . . . . . ....

  • Page 13

    ▫ driver and right front passenger supplemental restraint system (srs) – airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 ▫ airbag system components . . . . . . . . . . . . . . 53 ▫ advanced front airbag features . . . . . . . . . . 54 ▫ airbag deployment sensors and controls . . ...

  • Page 14

    A word about your keys key fob with remote keyless entry (rke) — if equipped your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a wireless ignition node (win) with integral ignition switch. You can insert the key fob into th...

  • Page 15

    Key fob the key fob operates the ignition switch. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the rke transmitter go dead. You can k...

  • Page 16

    To remove the emergency key, slide the mechanical latch at the top of the key fob sideways with your thumb and then pull the key out with your other hand. Note: you can insert the double-sided emergency key into the lock cylinder with either side up. Removing key fob from ignition place the shift le...

  • Page 17

    (evic)/personal settings (customer-programmable features)” in “understanding your instrument panel” for further information. Warning! • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fata...

  • Page 18

    Sentry key 姞 the sentry key 威 immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses a key fob with a factory-mated remot...

  • Page 19

    All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics. Replacement keys note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to ...

  • Page 20

    General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference...

  • Page 21

    The alarm is set, the vehicle security light will flash at a slower rate to indicate that the system is armed. Note: if the vehicle security light stays on continu- ously during vehicle operation, have the system checked by an authorized dealer. To disarm the system use the rke transmitter to unlock...

  • Page 22

    Note: • the front courtesy overhead console and door cour- tesy lights do not turn off if the dimmer control is in the interior lights on position (extreme right posi- tion). • the illuminated entry system will not operate if the dimmer control is in the extreme left position. Remote keyless entry (...

  • Page 23

    To unlock the doors press and release the unlock button on the rke transmitter once to unlock the driver’s door (if evic is setup for driver door first, otherwise this will unlock all doors), or twice within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unloc...

  • Page 24

    Note: pressing the lock button on the rke transmit- ter while you are inside the vehicle will activate the vehicle security alarm system. Opening a door with the vehicle security alarm system activated will cause the alarm to sound. Press the unlock button to deactivate the vehicle security alarm sy...

  • Page 25

    Security alarm system activated will cause the alarm to sound. Press the unlock button to deactivate the vehicle security alarm system. To lock the doors press and release the lock button on the rke transmit- ter to lock all doors. The turn signal lights will flash and the horn will chirp to acknowl...

  • Page 26

    Note: pressing the lock button on the rke transmit- ter while you are in the vehicle will activate the vehicle security alarm system. Opening a door with the vehicle security alarm system activated will cause the alarm to sound. Press the unlock button to deactivate the vehicle security alarm system...

  • Page 27

    Transmitter battery replacement the recommended replacement battery is one cr2032 battery. Note: • perchlorate material — special handling may apply. See www.Dtsc.Ca.Gov/hazardouswaste/perchlorate • do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With...

  • Page 28

    If your rke transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the rke transmitter. The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mo...

  • Page 29

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Car- bon monoxide is poisonous and can cause serious injury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 30

    • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the remote start mode. • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch must be cycled to the on/run position be...

  • Page 31

    Turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These features will stay on through the duration of remote start or until the ignition switch is turned to the on/run position. The remote start comfort system can ...

  • Page 32

    Power door locks — if equipped a power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. If you press the power door lock switch while the key fob is in the ignition, and any front door is open, the power locks will not operate. This prevents you from ac...

  • Page 33

    • for vehicles not equipped with the evic, perform the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt. (fastening the seat belt will cancel any chiming that may confuse you during this programming procedure.) 3. Place the key fob into the ignition. 4. Within...

  • Page 34

    • for vehicles not equipped with the evic, perform the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt. (fastening the seat belt will cancel any chimes that may be confusing during this programming procedure.) 3. Insert the key fob into the ignition. 4. Withi...

  • Page 35

    Child-protection door lock to provide a safer environment for children riding in the rear seat, the rear doors (if equipped) of your vehicle have the child-protection door lock system. To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to enga...

  • Page 36

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: • after setting the child-protection door lock system, always test the door from the inside to make certain it is in the des...

  • Page 37

    The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of the crew cab models. The windows will operate when the ig...

  • Page 38

    To open the window part way, press to the first detent and release it when you want the window to stop. Auto-up feature with anti-pinch protection (4-door models driver’s and front passenger door only) — if equipped lift the window switch to the second detent, release, and the window will go up auto...

  • Page 39

    Press the window lock button into the latched or down position. To enable the window controls, press the win- dow lock button again and return the switch to the released or up position. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type soun...

  • Page 40

    • knee bolsters/blockers for front seat occupants • all seat belt systems (except driver’s, first and second row center position) include automatic locking re- tractors (alr) if you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for chi...

  • Page 41

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in an accident. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 42

    Warning! (continued) • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of an accident best. Wearing your belt in the wrong place could make your injuries in an accident...

  • Page 43

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” pulling out latch plate and webbing latch plate to buckle 2 things to know before starting your vehicle 41.

  • Page 44

    Warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you properly. In a sudden stop you c...

  • Page 45

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in an accident. War...

  • Page 46

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in an accident and leave you with no protecti...

  • Page 47

    2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible “click”. For proper seatbelt usage, refer “lap/shoulder belt operating instructions”. Detaching buckle with sea...

  • Page 48

    Warning! • if the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in an accident. • when reattaching the black latch and black buckle, ensure the seat ...

  • Page 49

    Warning! • if the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in an accident. • when reattaching the black latch and black buckle, ensure the seat ...

  • Page 50

    Adjustable upper shoulder belt anchorage in the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that fits you best. As a guide, ...

  • Page 51

    Warning! • a lap belt worn too loose or too high is dangerous. • a belt worn too loose can allow you to slip down and under the belt in a collision. • a belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal inju...

  • Page 52

    Enhanced seat belt use reminder system (beltalert 姞) beltalert 威 is a feature intended to remind the driver to fasten their seatbelt. This feature is active whenever the ignition is on. If the driver is unbelted, the seat belt reminder light will turn on and remain on until the driver seatbelt is fa...

  • Page 53

    4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming. Beltalert 威 can be reactivated by repeating this procedure. Note: although beltalert 威 has been deactivated, the seat belt reminder light will continue to illuminate while the driver’s ...

  • Page 54

    Driver and right front passenger supplemental restraint system (srs) – airbag this vehicle has advanced front airbags for both the driver and front passenger (if equipped) as a supplement to the seat belt restraint systems. The driver’s advanced front airbag is mounted in the center of the steering ...

  • Page 55

    The advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the...

  • Page 56

    Advanced front airbag features the advanced front airbag system has multistage driver and front passenger (if equipped) airbags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint con- troller (orc). The first stage inflator is trigg...

  • Page 57

    Here are some simple steps you can take to minimize the risk of harm from a deploying airbag: children 12 years old and under should always ride buckled up in a rear seat. Warning! Infants in rear-facing child restraints should never ride in the front seat of a vehicle with a passenger advanced fron...

  • Page 58

    If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer center. Phone numbers are provided under ⬙if you need assistance ⬙. Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your s...

  • Page 59

    The advanced front airbags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, advanced front airbags...

  • Page 60

    It also includes diagnostics that will illuminate the instru- ment cluster airbag warning light if a malfunction is noted that could affect the airbag system. The diagnostics also record the nature of the malfunction. Warning! Ignoring the airbag warning light in your instru- ment panel could mean y...

  • Page 61

    Enhanced accident response system in the event of an impact causing airbag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the orc will determine whether to have the enhanced accident response system perform the follow- ing ...

  • Page 62

    Airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, fol...

  • Page 63

    Warning! (continued) • do not attempt to modify any part of your ad- vanced airbag system. The airbag may inflate accidentally or may not function properly if modi- fications are made. Take your vehicle to an autho- rized dealer for any advanced airbag system ser- vice. If your seat, including your ...

  • Page 64

    Check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good. Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to r...

  • Page 65

    To read data recorded by an edr, special equipment is required, and access to the vehicle or the edr is needed. In addition to the vehicle manufacturer, other parties such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. C...

  • Page 66

    Of child restraints can be used rearward-facing: infant carriers and ⬙convertible⬙ child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt. • the infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 ...

  • Page 67

    Warning! • rearward-facing child seats must never be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • improper installation can lead to failure of an infant or child restraint. It could come loos...

  • Page 68

    From the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. • if the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle,...

  • Page 69

    If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Lower anchors and tether for children (latch) each vehicle is equipped with the child restraint anchor- age system calle...

  • Page 70

    Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seat back tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-o...

  • Page 71

    Installing the child restraint system warning! Do not install child restraint systems equipped with latch attachments in the center position of a crew cab model rear seat. The latch anchorages in this seat are designed for the two outboard seating posi- tions only. A child may be placed in the rear ...

  • Page 72

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 73

    Warning! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor posi- tions directly be...

  • Page 74

    Multiple child restraint installation sequence (crew cab — rear seats) crew cab 1. The tether straps loops are located between the rear glass and the rear seat. There is a tether strap loop located behind each seating position. You can gain access to the center seating position tether strap loop by ...

  • Page 75

    3. Pass each tether strap hook under the head restraint and through the loop of webbing behind the child seat. 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the anchor loop. 5. Place a child restraint on the center rear seat and adjust the tether strap so t...

  • Page 76

    Transporting pets airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in an accident. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat...

  • Page 77

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- o...

  • Page 78

    Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, ...

  • Page 79

    Floor mat safety information always use floor mats designed to fit the foot well of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in ...

  • Page 80

    Warning! (continued) • always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • if required, mounting posts must be properly installed, if not equipped ...

  • Page 81: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 83 ▫ automatic dimming mirror — if equipped . . . 84 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 84...

  • Page 82

    ▫ things you should know about your uconnect™ phone . . . . . . . . . . . . . . . . . . . . 110 ▫ general information . . . . . . . . . . . . . . . . . . 121 䡵 voice command — if equipped . . . . . . . . . . . 121 ▫ voice command system operation . . . . . . . . 121 ▫ commands . . . . . . . . . . . ...

  • Page 83

    ▫ automatic headlights . . . . . . . . . . . . . . . . . 144 ▫ headlight delay . . . . . . . . . . . . . . . . . . . . . 145 ▫ parking lights and panel lights . . . . . . . . . 146 ▫ fog lights — if equipped . . . . . . . . . . . . . . 146 ▫ interior lights . . . . . . . . . . . . . . . . . . . . . ...

  • Page 84

    䡵 overhead console — if equipped . . . . . . . . . . 159 ▫ courtesy/reading lights . . . . . . . . . . . . . . 160 䡵 electrical power outlets . . . . . . . . . . . . . . . . . 161 䡵 cigar lighter and ash receiver — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 164 䡵 power inverter ...

  • Page 85

    Mirrors inside day/night mirror headlight glare can be reduced by moving the small control lever under the mirror to the night position (lever flipped toward the rear of vehicle). The mirror should be adjusted with the lever set in the day position (lever flipped toward the windshield). The mirror s...

  • Page 86

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. Ca...

  • Page 87

    Warning! Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or d...

  • Page 88

    Power mirrors — if equipped the controls for the power mirrors are located on the driver’s door trim panel. The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. Power mirror controls power mirror controls 1 — mirror select buttons 2 — mirror control 86 u...

  • Page 89

    To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Power folding outside mirrors — if equipped if equipped with power folding mirrors, they can...

  • Page 90

    The switch for the power folding mirrors is located between the power mirror switches l (left) and r (right). Press the switch once and the mirrors will fold in, pressing the switch a second time will return the mirrors to the normal driving position. Note: ten or more switch activations within one ...

  • Page 91

    “slide-on-rod” features of sun visor — if equipped the sun visor “slide-on-rod” feature allows for addi- tional flexibility in positioning the visor to block out the sun. To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until...

  • Page 92

    Trailer towing mirrors — if equipped these mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped in or out). Note: fold the trailer towing mirrors rearwa...

  • Page 93

    Uconnect™ phone — if equipped uconnect™ phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ phone al- lows you to dial a phone number with your mobile phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s a...

  • Page 94

    Linked (or paired) mobile phone can be used with the system at a time. The system is available in english, spanish, or french languages. Warning! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ...

  • Page 95

    Operation voice commands can be used to operate the uconnect™ phone and to navigate through the uconnect™ phone menu structure. Voice commands are required after most uconnect™ phone prompts. You will be prompted for a specific command and then guided through the available options. • prior to giving...

  • Page 96

    Cancel command at any prompt, after the beep, you can say “cancel” and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (link) uconnect™ phone to a mobile phone to begin using your uconnect™ phone, you must pair your compatib...

  • Page 97

    Phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the uconnect™ phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at an...

  • Page 98

    Add names to your uconnect™ phonebook note: adding names to the uconnect™ phonebook is recommended when the vehicle is not in motion. • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook new entry”. • when prompted, say the name of the new entry. Use of long...

  • Page 99

    • to call a name from downloaded (or uconnect™) phonebook, follow the procedure in “call by saying a name” section. • automatic download and update, if supported, begins as soon as the bluetooth 威 wireless phone connection is made to the uconnect™ phone, for example, after you start the vehicle. • a...

  • Page 100

    Object exchange profile (obex). Please see your phone owner’s manual for specific instructions on how to send these entries from your phone. Note: • the phone handset must support bluetooth威 obex transfers of phonebook entries to use this feature. • some phones cannot send phonebook entries if they ...

  • Page 101

    After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. “phonebook edit” can be used to add another phone number to a name entry that already exists in the phonebo...

  • Page 102

    Delete/erase “all” uconnect™ phonebook entries • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook erase all”. • the uconnect™ phone will ask you to verify that you wish to delete all the entries from the phonebook. • after confirmation, the phonebook entri...

  • Page 103

    Phone call features the following features can be accessed through the uconnect™ phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the uconnect™ phone. Check with your mobile se...

  • Page 104

    In progress. To go back to the first call, refer to “toggling between calls” in this section. To combine two calls, refer to “conference call” in this section. Place/retrieve a call from hold to put a call on hold, press the button until you hear a single beep. This indicates that the call is on hol...

  • Page 105

    Call termination to end a call in progress, momentarily press the button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is ...

  • Page 106

    Uconnect™ phone features language selection to change the language that the uconnect™ phone is using: • press the button to begin. • after the “ready” prompt and the following beep, say the name of the language you wish to switch to english, espanol, or francais. • continue to follow the system prom...

  • Page 107

    Canada and 060 for mexico). The number dialed may not be applicable with the available mobile service and area. • if supported, this number may be programmable on some systems. To do this, press the button and say “setup”, followed by “emergency”. • the uconnect™ phone does slightly lower your chanc...

  • Page 108

    Paging to learn how to page, refer to “working with automated systems”. Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the uconnect™ phone. Voice mail calling to learn how to access your voice mail, refer to “working with automate...

  • Page 109

    The uconnect™ phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone. Note: • you may not hear all of the tones due to mobile phone network configurations. This is normal. • some paging and voice mail systems have system time out settings tha...

  • Page 110

    Phone and network status indicators if available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your mobile phone, the uconnect™ phone will provide notification to inform you of your phone and network status when you are attempting to make a phone cal...

  • Page 111

    Advanced phone connectivity transfer call to and from mobile phone the uconnect™ phone allows ongoing calls to be trans- ferred from your mobile phone to the uconnect™ phone without terminating the call. To transfer an ongoing call from your uconnect™ phone paired mobile phone to the uconnect™ phone...

  • Page 112

    • after the “ready” prompt and the following beep, say “setup select phone” and follow the prompts. • you can also press the button at any time while the list is being played, and then choose the phone that you wish to select. • the selected phone will be used for the next phone call. If the selecte...

  • Page 113

    • press the button and say the “voice training, system training, or start voice training” command. You can either press the uconnect™ phone button to restore the factory setting or repeat the words and phrases when prompted by the uconnect™ phone. For best results, the voice training session should ...

  • Page 114

    • fully closed windows, • dry weather condition. • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system such as voice mail, or when sending a page, at the...

  • Page 115

    • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect™ phone. • echo at the phone far end can sometimes be reduced by lowering the in-veh...

  • Page 116

    Send messages: you can send messages using uconnect™ phone. To send a new message: • press the button. • after the “ready” prompt and the following beep, say “sms send” or “send messages.” • you can either say the message you wish to send or say “list messages.” there are 20 preset messages. To send...

  • Page 117

    16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and th...

  • Page 118

    116 understanding the features of your vehicle.

  • Page 119

    3 understanding the features of your vehicle 117.

  • Page 120

    118 understanding the features of your vehicle.

  • Page 121

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 3 understa...

  • Page 122

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 123

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 124

    Note: if you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system i...

  • Page 125

    Changing the volume 1. Start a dialogue by pressing the voice command button. 2. Say a command (e.G., “help”). 3. Use the on/off volume rotary knob to adjust the volume to a comfortable level while the voice command system is speaking. Please note the volume setting for voice command is different th...

  • Page 126

    • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “main menu” (to switch to the main menu) satellite radio to switch to satellite radio mode, say “sat” or “satellite radio”. In this mode, you may say the...

  • Page 127

    Memo to switch to the voice recorder mode, say “memo”. In this mode, you may say the following commands: • “new memo” (to record a new memo) — during the recording, you may press the voice command button to stop recording. You proceed by saying one of the following commands: − “save” (to save the me...

  • Page 128

    • “language french” • “language spanish” • “tutorial” • “voice training” note: keep in mind that you have to press the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice ...

  • Page 129

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Manual seat adjuster — if equipped both front seats are independently adjustable forward or r...

  • Page 130

    Warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Manual reclining seats — if equipped the recli...

  • Page 131

    Warning! • actuating the recliner handle will allow the seat- back to swing (dump) forward on manual recliner seats. Do not stand or lean in front of the seat while actuating the handle. The seatback may swing forward and hit you causing injury. This dump feature allows access to the storage bin beh...

  • Page 132

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 133

    Note: the rear center head restraint (crew cab only) is fixed and cannot be adjusted. Power seats — if equipped some models may be equipped with driver and passen- ger eight-way power seats. The power seat switches are located on the outboard side of the front seat cushions. There are two power seat...

  • Page 134

    Adjusting the sear forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting the seat up or down the height of the seats...

  • Page 135

    Warning! (continued) • do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Caution! Do not place any article under a power seat or impede its abili...

  • Page 136

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters in both the seat cushions and seatbacks. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- ha...

  • Page 137

    Press the switch once to select high- level heating. Press the switch a sec- ond time to select low-level heating. Press the switch a third time to shut the heating elements off. Note: • once a heat setting is selected, heat will be felt within two to five minutes. • the engine must be running for t...

  • Page 138

    Indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high- level heating. Press the switch a sec- ond time to select low-level heating. Press the switch a third time to shut the...

  • Page 139

    Press the switch once to choose high, press it a second time to choose low. Pressing the switch a third time will turn the ventilated seat off. When high speed is selected both lights on the switch will be illuminated. When low speed is selected one light will be illuminated. Note: the engine must b...

  • Page 140

    The memory seat buttons are located on the outboard side of the drivers seat cushion. The memory buttons 1 and 2 can be programmed to recall the driver’s seat position, driver’s outside mirror position, adjustable brake, accelerator pedals position, automatic temperature control (atc) temperature se...

  • Page 141

    1. Turn the vehicle key to the on/run position. 2. Adjust the driver’s seat, recliner, and both sideview mirrors to the desired positions. Note: not all motors may be moved at one time. Refer to “seats/eight-way power seat” in this section for further information. 3. Adjust the brake and accelerator...

  • Page 142

    To recall the memory settings for driver one, press memory button number 1 on the driver’s seat or the unlock button on the rke transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 on the driver’s seat or the unlock button on the rke tran...

  • Page 143

    Vehicles equipped with the electronic vehicle informa- tion center (evic), refer to “electronic vehicle informa- tion center (evic)/customer-programmable features” in “understanding your instrument panel” for further information. Self-limiting control the memory system includes a self-limiting contr...

  • Page 144

    To open and close the hood to open the hood, two latches must be released. 1. Pull the hood release lever located below the steering wheel at the base of the instrument panel. 2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, b...

  • Page 145

    Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle...

  • Page 146

    Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less suscep- tible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility ...

  • Page 147

    When the system is on, the headlight delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch to the off position. To turn the automatic headlights off, turn the headlight switch out of the auto position. Note: the engine must be runnin...

  • Page 148

    Parking lights and panel lights to turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the o (off) position. Fog lights — if equipped the fog lights are turned on by placing the headlight r...

  • Page 149

    Interior lights courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the bottom of the switch) is rotated to the far right detent position, or if equipped, when the unlock button is pressed on the remote keyless entry (rke) transmitter. W...

  • Page 150

    Cargo light the cargo lights are turned on by pressing on the cargo button. The cargo lights will also turn on for approximately 30 seconds when a rke transmitter unlock button is pressed, as part of the illuminated entry feature. Lights-on reminder if the headlights, parking lights, or cargo lights...

  • Page 151

    Daytime running lights — if equipped the headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except park. This provides a constant ⬙lights on⬙ condition until the ignition is turned off. The lights illuminate at less than 50% of normal intensity....

  • Page 152

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Flash-to-pass you can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer-...

  • Page 153

    Intermittent wiper system the intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay inter...

  • Page 154

    To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Warning! Sudden loss of visibility through the windshield could lead ...

  • Page 155

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this war...

  • Page 156

    The adjustable pedal switch is located to the left side of the steering column. Adjustment 1. Position the driver’s seat so that you are at least 10 in (25.4 cm) away from the airbag, located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch...

  • Page 157

    Caution! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path. Warning! Do not adjust the pedals while the vehicle is ...

  • Page 158

    On during a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further information. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol u...

  • Page 159

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 160

    Speed memory. Pushing the on/off button to the off position or turning off the ignition erases the set speed memory. To resume speed to resume a previously set speed, raise the electronic speed control lever (resume accel) upwards and release. Resume can be used at any speed above 30 mph (50 km/h). ...

  • Page 161

    Your vehicle may experience a downshift (automatic transmissions only) while climbing uphill or descending downhill. This downshift is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without electronic speed control. War...

  • Page 162

    Courtesy/reading lights both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the unlock button is pressed on the remote keyless ent...

  • Page 163

    Note: the courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the ignition is turned off, they will extinguish after 15 minutes. Electrical power outlets the auxili...

  • Page 164

    The auxiliary power outlets can be found in the following locations: • lower left and lower right of the center stack. • inside the top storage tray. • inside the upper lid of the center storage compartment — if equipped. • rear of the center console storage compartment — crew cab. Power outlet — fl...

  • Page 165

    The key symbol indicates that this outlet can supply power when the key is in the on or acc positions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge. Warning! To avoid serious injury or death: • only...

  • Page 166

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 167

    For vehicles equipped with a floor console the cuphold- ers may be used. Power inverter — if equipped a 115 volt (150 watts maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power device...

  • Page 168

    The power inverter switch is located on the switch bank below the climate controls. To turn on the power outlet, press the switch once. Press the switch a second time to turn the power outlet off. Note: • when the power inverter switch is pressed, there will be a delay of approximately one second be...

  • Page 169

    Cupholders front instrument panel cupholders — (40–20–40 seats) the cupholders are located in the pull-out tray on the center stack of the instrument panel. Front instrument panel cupholders — floor storage bin for vehicles equipped with bucket seats two cupholders are located in the floor storage b...

  • Page 170

    Rear cupholder — crew cab crew cab vehicles are equipped with rear cupholders located in the center armrest. Storage glove box storage the glove box is located on the passenger side of the instrument panel and features both an upper (if equipped) and lower storage area. Crew cab rear armrest cuphold...

  • Page 171

    To open the upper glove box push upward on the handle release. The glove box door will automatically open. To open the lower glove box, pull on the handle to release the latch and lower the door. Upper glove box lower glove box 3 understanding the features of your vehicle 169.

  • Page 172

    Door storage front door storage — if equipped storage areas and bottle holders (drivers side only) are located in the door trim panels. Rear door storage — crew cab storage compartments are located in both the driver and passenger door trim panels. Front door storage rear door storage 170 understand...

  • Page 173

    Center storage compartment — if equipped the center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Warning! • this armrest is not a seat. Anyone seated on the armrest could be seri...

  • Page 174

    Pull on the upper handle on the front of the armrest to raise the cover. The upper storage area contains a 12 volt power outlet that can be used to power small electrical devices, refer to “electrical power outlets” for further information. With the upper lid closed, pull on the lower handle to open...

  • Page 175

    Seatback storage located in the back of both the driver and passenger front seats are pockets that can be used for storage. Storage (regular cab) the storage bin is located behind the front seats and runs the length of the cab. Drivers side seatback storage storage bin 3 understanding the features o...

  • Page 176

    Storage and seats (crew cab) the crew cab models provide additional storage under the rear seats. Lift the seats to access the storage com- partment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Caution! Always lift the storage compartment lids by using ...

  • Page 177

    Rear window features rear window defroster the rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. T...

  • Page 178

    Caution! (continued) • do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • keep all objects a safe distance from the window. Power sliding rear window — if equipped the switch for the power sliding rear window is located on the overhead cons...

  • Page 179: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 181 䡵 instrument cluster — base . . . . . . . . . . . . . . . 182 䡵 instrument cluster — premium . . . . . . . . . . . 183 䡵 instrument cluster descriptions . . . . . . . . . . . 184 䡵 electronic v...

  • Page 180

    䡵 media center 730n/430/430n (rer/rbz/ rhb) cd/dvd/hdd/nav — if equipped . . . 216 ▫ operating instructions (voice command system) — if equipped . . . 216 ▫ operating instructions (uconnect™ phone) — if equipped . . . . . . . 216 䡵 media center 130 (sales code res) . . . . . . . . . 216 ▫ operating ...

  • Page 181

    ▫ list or browse mode . . . . . . . . . . . . . . . . . 244 䡵 uconnect™ multimedia (satellite radio) — if equipped (ren/rer/res radios only) . . . . 246 ▫ system activation . . . . . . . . . . . . . . . . . . . . 246 ▫ electronic serial number/sirius identification number (esn/sid) . . . . . . . . ....

  • Page 182

    ▫ summer operation . . . . . . . . . . . . . . . . . . . 262 ▫ winter operation . . . . . . . . . . . . . . . . . . . . 263 ▫ vacation/storage . . . . . . . . . . . . . . . . . . . . 263 ▫ window fogging and frosting . . . . . . . . . . 263 ▫ outside air intake . . . . . . . . . . . . . . . . . . . ...

  • Page 183

    Instrument panel features 1 — headlight switch 7 — 115v power inverter outlet 13 — transfer case position switch 2 — instrument cluster 8 — power outlet 14 — ignition switch 3 — radio 9 — lower switch bank 15 — hood release 4 — upper switch bank 10 — cup holders 16 — parking brake release 5 — upper ...

  • Page 184

    Instrument cluster — base 182 understanding your instrument panel.

  • Page 185

    Instrument cluster — premium 4 understanding your instrument panel 183.

  • Page 186

    Instrument cluster descriptions 1. Tachometer the tachometer indicates engine speed in revolutions per minute. Caution! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur. 2. Turn signal indicators the arrow will flash with the exterior tu...

  • Page 187

    Caution! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear continuo...

  • Page 188

    Rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels. 7. Electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. The light will come on when the ignition is first t...

  • Page 189

    For vehicles equipped with a premium cluster this indi- cator will display in the electronic vehicle information center (evic). Refer to ”electronic vehicle information center (evic) — if equipped” for further information. 10. Tow/haul the tow haul button is located on the center stack switch bank. ...

  • Page 190

    Before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero. The two trip odometers show individual trip...

  • Page 191

    If the vehicle diagnostic system deter- mines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the odometer display area. Tighten the fuel filler cap properly and press the trip button to turn off the message. If the problem continues, the...

  • Page 192

    2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. 15. Engine temp...

  • Page 193

    Lever to activate ers. Refer to “automatic transmission” in “starting and operating” for further information. 17. Low fuel light when the fuel level reaches approximately 3.0 gal (11.0 l) this light will turn on, and remain on until fuel is added. For vehicles equipped with a premium cluster this in...

  • Page 194

    20. Cargo light the cargo light will illuminate when the cargo light is activated by pressing the cargo light button on the headlight switch. 21. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, i...

  • Page 195

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the abs, are also equipped with electronic brake force dist...

  • Page 196

    For vehicles equipped with a premium cluster this indi- cator will display in the electronic vehicle information center (evic). Refer to ”electronic vehicle information center (evic) — if equipped” for further information. 23. Malfunction indicator light (mil) the malfunction indicator light (mil) i...

  • Page 197

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injur...

  • Page 198

    27. Transmission temperature warning light this light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation ...

  • Page 199

    28. Seat belt reminder light when the ignition switch is first turned to on/ run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s seat belt rema...

  • Page 200

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. Note: the compass on your vehicle is self-calibrating, eliminating the need to manually calibrate the compass...

  • Page 201

    • audio modes display steering wheel evic control button, as it appears on the left side of the steer- ing wheel. Press and release the up button to scroll up- ward through the main menus (dte, mi/gal, system info, messages, units, setup) and sub menus. Press and release the down button to scroll do...

  • Page 202

    Electronic vehicle information center (evic) displays when the appropriate conditions exist, the evic displays the following messages: • left front turn signal lamp out • right front turn signal lamp out • left rear turn signal lamp out • right rear turn signal lamp out • service air filter • check ...

  • Page 203

    • turn signal on • rke battery low • low washer fluid • oil change due > dealer info • park assist on • park assist off • warning object detected • left front turn signal light out • left rear turn signal light out • right front turn signal light out • right rear turn signal light out • service park...

  • Page 204

    • memory system unavailable — seatbelt buckled • memory 1 profile recall • memory 2 profile recall • adjustable pedals unavailable — vehicle in reverse • adjustable pedals unavailable — cruise engaged • to tow vehicle safely, read neutral shift procedure in owners manual evic warning lights • door a...

  • Page 205

    Vehicle is experiencing a problem with the charging system. Obtain service immediately. See an autho- rized dealer. • electronic speed control light this light will turn on when the electronic speed control is on. • electronic throttle control (etc) light this light informs you of a problem with the...

  • Page 206

    If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into neutral and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if...

  • Page 207

    • loose gascap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap icon will display in the telltale display area. Tighten the fuel filler cap properly and press the select button to turn off the message. If the prob...

  • Page 208

    Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. Dte cannot be reset through the return b...

  • Page 209

    The trip functions mode displays the following informa- tion. • trip a shows the total distance traveled for trip a since the last reset. • trip b shows the total distance traveled for trip b since the last reset. • elapsed time shows the total elapsed time of travel since the last reset when the ig...

  • Page 210

    • trans temperature displays the actual transmission temperature. • engine hours displays the hours of engine operation. • trailer brake — if equipped displays trailer brake output power and trailer brake status indicator. Units press and release the up or down button until “units” displays in the e...

  • Page 211

    Temperature sensor caused by the snowplow. In addi- tion, on vehicles equipped with automatic tempera- ture control (atc), it is suggested that the interior cabin temperature be manually controlled should the system not perform as desired while in automatic mode. Both the outside temperature display...

  • Page 212

    5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “cal” indicator turns off. The compass will now function normally. Compass variance compass variance is the difference between magnetic north and geographic north. To compensate for the differen...

  • Page 213

    3. Press the down button until the “compass variance” message is displayed in the evic, then press the select button. The last variance zone number displays in the evic. 4. Press and release the select button until the proper variance zone is selected, according to the map. 5. Press and release the ...

  • Page 214

    Auto lock doors when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated, or the check-mark...

  • Page 215

    Select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated. Horn with remote start when this feature is selected, a short horn sound will occur when the rke transmitter remote start button i...

  • Page 216

    Then press and release the select button until a check- mark appears next to the setting, showing that setting has been selected. Headlamps with wipers when this feature is selected and the headlight switch is in the auto position, the headlights will turn on approximately 10 seconds after the wiper...

  • Page 217

    Select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated. Note: the seat will return to the memorized seat location (if recall memory with remote key unlock is set to on) when the rke tran...

  • Page 218

    Media center 730n/430/430n (rer/rbz/rhb) cd/dvd/hdd/nav — if equipped note: the sales code is located on the lower right side of the unit’s faceplate. Refer to your uconnect™ multimedia rer, rbz or rhb user’s manual for detailed operating instructions. Operating instructions (voice command system) —...

  • Page 219

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 220

    4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the ...

  • Page 221

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button press the buttons to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button...

  • Page 222

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 223

    Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 224

    Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek button to move to the next ran- domly selected track. Press the ...

  • Page 225

    • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a three- character extension) • level 2: 31 (including a separator ⬙.⬙ and a three- character extension) multisession disc formats are supported by the radio. Multisession discs may contain combinations...

  • Page 226

    Playlist files are not supported. Mp3 pro files are not supported. Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading time...

  • Page 227

    Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for five seconds (when ignition is off). Media center 130 with satellite radio (sales code res+rsc) note: the radio sales code is located on the lower right side of the radio faceplate. ...

  • Page 228

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 229

    Phone button uconnect™ phone — if equipped press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in “under- standing the features if your vehicle”. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with...

  • Page 230

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either am or fm frequencies. Tune control turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decre...

  • Page 231

    Or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast music type information. Toggle the music type button to select the following format types: program type 16-digit character display no progra...

  • Page 232

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 233

    And 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to ...

  • Page 234

    Caution! • this cd player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • res is a single cd player. Do not attempt to insert a second cd if one is alrea...

  • Page 235

    Rw/ff press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am/fm button press the button to select either am or fm mode. Set/rnd button (random play button) press t...

  • Page 236

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 237

    Rates (vbr) are also supported. The majority of mp3 files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rates. Mpeg specification sampling frequency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio la...

  • Page 238

    List button (cd mode for mp3 play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that folde...

  • Page 239

    Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is off). Uconnect™ multimedia (satellite radio) — if equipped satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide c...

  • Page 240

    Using the tune/scroll control knob until sirius id is selected. Press the tune/scroll control knob and the sirius id number will display. The sirius id number display will time out in two minutes. Press any button on the radio to exit this screen. Selecting uconnect™ multimedia (satellite) mode pres...

  • Page 241

    Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without st...

  • Page 242

    By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same selected music type name. If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the prese...

  • Page 243

    Operating instructions - uconnect™ phone (if equipped) refer to “uconnect™ phone” in “understanding the features if your vehicle”. Universal consumer interface (uci) 0.5 — if equipped note: this section is for sales code res and req/ rel/ret radios only with uconnect™. For sales code rer, rbz, ren, ...

  • Page 244

    Connecting the ipod 姞 use the provided connection cable to connect an ipod 威 to the vehicle’s 16–pin connector port (which is located in the glove compartment on some vehicles). Once the ipod 威 is connected and synchronized to the vehicle’s uci system (ipod 威 may take a few seconds to connect), the ...

  • Page 245

    Play mode when switched to uci mode, the ipod 威 automatically starts play mode. In play mode, use the following buttons on the radio faceplate to control the ipod 威 and display data: • use the tune control knob to select the next or previous track. • turning it clockwise (forward) by one click, whil...

  • Page 246

    Screens have been viewed, the last info button press will go back to the play mode screen on the radio. • pressing the repeat button will change the ipod威 mode to repeat the current playing track. • press the scan button to use ipod威 scan mode, which will play the first five seconds of each track in...

  • Page 247

    • during all list modes, the ipod威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backwards (counter-clockwise) to get to the track faster. • in list mode, the radio preset buttons are used as shortcuts to the following lists on the ipod 威...

  • Page 248

    Caution! • leaving the ipod威 (or any supported device) any- where in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer’s guidelines. • placing items on the ipod威, or connections to the ipod 威 in the vehicle, can cause damage to the devic...

  • Page 249

    Information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www- .Siriuscanada.Ca for canadian residents. Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic ser...

  • Page 250

    Bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or...

  • Page 251

    Info button pressing the info button will cycle the display informa- tion between artist, song title, and composer (if avail- able). Also, pressing and holding the info button for an additional three seconds will make the radio display the song title all of the time (press and hold again to return t...

  • Page 252

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set button – to set the pushbutton memory when...

  • Page 253

    Steering wheel audio controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a pushbutton in the center. Pressing the top of the switch will incre...

  • Page 254

    The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pre-set pushbuttons. Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginnin...

  • Page 255

    Note: if you experience difficulty in playing a particu- lar disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile pho...

  • Page 256

    Manual heating and air conditioning system the controls for the manual heating and air conditioning system in this vehicle consist of a series of outer rotary dials and inner push knobs. These comfort controls can be set to obtain desired interior conditions. Front blower control there are four blow...

  • Page 257

    Temperatures. Rotating the knob clockwise, into the red area, indicates warmer temperatures. Note: if your air conditioning performance seems lower than expected, check the front of the a/c con- denser (located in front of the radiator), for an accumu- lation of dirt or insects. Clean with a gentle ...

  • Page 258

    Mix mode air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort, while reducing moisture on the windshield. Defrost mode air is directed thr...

  • Page 259

    • in cold or damp weather, the use of the recirculation mode will cause windows to fog on the inside because of moisture buildup inside the vehicle. For maximum defogging, select the outside air position. • the a/c can be deselected manually without disturb- ing the mode control selection by pressin...

  • Page 260

    Max a/c for maximum cooling, when max a/c is selected the a/c is turned on automatically and the air is recircu- lated. Note: a/c cannot be deselected when in max a/c position. The led will blink three times if the a/c button is pushed. Automatic temperature control (atc) — if equipped • the automat...

  • Page 261

    Automatic operation 1. Position the mode control knob to the auto position on the automatic temperature control (atc) panel. 2. Position the blower control knob in the auto posi- tion on the atc panel. 3. Next, adjust the temperature you would like the system to maintain by adjusting the driver and ...

  • Page 262

    Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to provide comfort as quickly as possible. • the temperature can be displayed in u.S. Or metric units by selecting the us/m customer-programmabl...

  • Page 263

    Selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode. The operator can also select the direction of the airflow by selecting one of the following positions. Panel mode air comes from the outlets in the instrument panel. Each of the...

  • Page 264

    The air conditioning (a/c) button allows the operator to manually activate or deactivate the air conditioning system. When in a/c mode and the atc is set to a cool temperature, dehumidified air flows through the air outlets. If economy mode is desired, press the a/c button to turn off the a/c mode i...

  • Page 265

    Winter operation to ensure the best possible heater and defroster perfor- mance, make sure the engine cooling system is function- ing properly and the proper amount, type, and concen- tration of coolant is used. Refer to “maintenance procedures” in “maintaining your vehicle” for proper coolant selec...

  • Page 266

    Operating tips 264 understanding your instrument panel.

  • Page 267: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 269 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 269 ▫ automatic transmission . . . . . . . . . . . . . . . 269 ▫ extreme cold weather (below 20°f or −7°c) . . . . . . . . . . . . . . . . . 2...

  • Page 268

    ▫ transfer case position indicator light . . . . . . 283 ▫ electronically shifted transfer case (four-position switch) – if equipped . . . . . . . 284 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . 288 䡵 limited-slip differential . . . . . . . . . . . . . . . . . 290 䡵 driving on slipper...

  • Page 269

    ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . 315 ▫ tread wear indicators . . . . . . . . . . . . . . . . . 316 ▫ life of tire . . . . . . . . . . . . . . . . . . . . . . . . 316 ▫ replacement tires . . . . . . . . . . . . . . . . . . . . 317 䡵 supplemental tire pressure information ...

  • Page 270

    ▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . 336 ▫ trailer and tongue weight . . . . . . . . . . . . . 336 ▫ towing requirements . . . . . . . . . . . . . . . . . 337 ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . 344 䡵 snowplow . . . . . . . . . . . . . ....

  • Page 271

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Warnin...

  • Page 272

    Extreme cold weather (below 20°f or ⫺7°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If engine fails to start if the engine fails to start after you have followed the “normal s...

  • Page 273

    If the engine has been flooded, it may start to run, but not have enough power to continue running when the key fob is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key fob once the engine is running smoo...

  • Page 274

    Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle spee...

  • Page 275

    Warning! (continued) • unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into park, remove the key fob from the ignition, a...

  • Page 276

    Shift lever out of the park position. To drive, move the shift lever from park or neutral to the drive position. Pull the shift lever toward you when shifting into reverse or park, or when shifting out of park. Electronic range select (ers) operation the electronic range select (ers) shift control a...

  • Page 277

    Are underdrive gears, and fourth gear is direct drive. Ers fifth gear (overdrive) is the same as the normal fourth gear. When in the drive position in first through fourth gear, the first tap down (-), will display the ers designation for the current gear (the transmission will not downshift). For e...

  • Page 278

    Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever in the p...

  • Page 279

    Neutral this range is for when the vehicle is standing for pro- longed periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. Drive this range provides all forward gears, including third gear direct and fourth and fifth gear ove...

  • Page 280

    Temperature warning light” may illuminate and the transmission may downshift out of overdrive until the transmission cools down. After cool down, the transmis- sion will resume normal operation. The transmission will downshift from overdrive to drive if the accelerator pedal is fully pressed at vehi...

  • Page 281

    The “tow/haul indicator light” will illuminate in the instrument cluster to indicate when the switch has been activated. Pressing the switch a second time restores normal operation. If the “tow/haul” mode is desired, the button must be pressed each time the engine is started. Torque converter clutch...

  • Page 282

    Four-wheel drive operation — if equipped four-wheel drive trucks are equipped with either a manually shifted transfer case or an electronically shifted transfer case. Refer to the operating instructions for your transfer case, located in this section for further informa- tion. Manually shifted trans...

  • Page 283

    When operating your vehicle in 4l, the engine speed is approximately three times that of the 2h or 4h positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circ...

  • Page 284

    2h rear-wheel drive high range - this range is for normal street and highway driving on dry hard surfaced roads. 4h four-wheel drive high range - this range locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. Additional traction for loose, sli...

  • Page 285

    2h or 4h ⇔ 4l with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift the transmission into neutral. While the vehicle is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position. Do not pause in transfer case neutral. Note: • pausing in transfer case ne...

  • Page 286

    Electronically shifted transfer case (four-position switch) – if equipped this is an electronic shift transfer case and is operated by the 4wd control switch (transfer case switch), which is located on the instrument panel. This electronically shifted transfer case provides four mode positions: • tw...

  • Page 287

    When additional traction is required, the transfer case 4wd lock and 4wd low positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed. This is accomplished by rotating the 4wd control switch to the desired position. Refer to...

  • Page 288

    2. The newly selected position indicator light will con- tinue to flash. 3. The transfer case will not shift. Note: before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob ba...

  • Page 289

    Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. ...

  • Page 290

    N neutral - this range disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “recreational towing” in starting and operating” for further information. Shifting procedure note: • if any of the requirements to select a new trans...

  • Page 291

    Note: the four-wheel drive system will not allow shifts between 2wd/4wd lock if the front and/or rear wheels are spinning (no traction). In this situation, the selected position indicator light will flash and the origi- nal position indicator light will remain on. At this time, reduce speed and stop...

  • Page 292

    Note: • if steps 1 or 2 of either the preferred or alternate procedure are not satisfied prior to attempting the shift, then the desired position indicator light will flash continuously while the original position indicator light is on, until all requirements have been met. • the ignition switch mus...

  • Page 293

    Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface. This could cause both rear wheels to spin, and allow the vehicle to slide sideways on the crowned surface of a road or in a turn. Driving on slippery surfaces acceleration rapid acceleration on snow c...

  • Page 294

    2. Slow down if the road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. Driving through water...

  • Page 295

    Shallow standing water although your vehicle is capable of driving through shallow standing water, consider the following caution and warning before doing so. Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the...

  • Page 296

    Warning! • driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • driving through standing water limits your vehi- cle’s braking capabilities, which increases stop- ping distances. Therefore, after driving thr...

  • Page 297

    System. This noise should be considered normal, and it does not in any way damage the steering system. Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the ...

  • Page 298

    If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Parking brake before leaving the vehicle, make sure that the parking...

  • Page 299

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 300

    Caution! If the “brake warning light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Brake system if power assist is lost for any reason (for example, repeated brake applications with the engine...

  • Page 301

    Four-wheel anti-lock brake system warning! The four-wheel anti-lock brake system contains sophisticated electronic equipment. It may be sus- ceptible to interference caused by improperly in- stalled or high output radio transmitting equipment. This interference can cause possible loss of anti-lock b...

  • Page 302

    Abs warning light the abs includes an amber warning light. When the light is illuminated, the abs is not functioning. The system reverts to standard, non-anti-lock brakes. Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stop...

  • Page 303

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 304

    Tires designed to this standard have the letter “t” molded into the sidewall preceding the size designa- tion. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing ...

  • Page 305

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 306

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 307

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire pressure cold tire inflation pressure is defined as the tire pressure after ...

  • Page 308

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar. Tire and loading information placard tire placard location tire and loading information placard 306 starting and operating.

  • Page 309

    This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the ...

  • Page 310

    Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx lbs or xxx kg” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined...

  • Page 311

    Starting and operating 309.

  • Page 312

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 313

    Warning! (continued) • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tir...

  • Page 314

    Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period. The cold tire inflation ...

  • Page 315

    4500/5500 tire inflation starting and operating 313.

  • Page 316

    When adjusting inflation pressure to a tire and wheel assembly mounted on a vehicle, use a remote mount automatic inflation kit or see your authorized dealer. Note: never attempt to re-inflate a tire and wheel assembly which has been run flat or is extremely under- inflated without first removing th...

  • Page 317

    Radial ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision result- ing in serious injury or death. Always use radial ply tires in sets of four (or six, in case of trucks with dual re...

  • Page 318

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 319

    Warning! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as ...

  • Page 320

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 321

    Supplemental tire pressure information — if equipped a light load vehicle condition is defined as two passen- gers [150 lbs (68 kg) each] plus 200 lbs (91 kg) of cargo. Cold tire inflation pressures for a lightly loaded vehicle will be found on the face of the driver’s door. Tire chains use “class u...

  • Page 322

    Caution! (continued) • observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower sug- gested operating speed of the chain manufacturer if different than the speed recommended by the manufacturer. These cautions apply...

  • Page 323

    Snow tires some areas of the country require the use of snow tires during the winter. All season tires satisfy this require- ment and can be identified by the m+s designation on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use s...

  • Page 324

    Refer to the “maintenance schedule” for the proper maintenance intervals. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. Note: on canadian vehicles only, if your vehicle is equipped with all-season ...

  • Page 325

    To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. Caution! 4500/5500 dual rear tires have only one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the on/off road tire. • when replaci...

  • Page 326

    Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) to define fuel properties necessary to deliver enhanced emissions, performance and durability for your vehicle. We recommend the use of gasolines that meet the wwfc s...

  • Page 327

    E-85 usage in non-flex fuel vehicles non-ffv vehicles are compatible with gasoline contain- ing 10% ethanol (e10). Gasoline with higher ethanol content may void the vehicle’s warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • ...

  • Page 328

    Allowed in the united states. Mmt is prohibited in federal and california reformulated gasoline. Materials added to fuel all gasolines sold in the united states are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal condition...

  • Page 329

    Caution! (continued) • the use of fuel additives which are now being sold as octane enhancers is not recommended. Many of these products contain high concentra- tions of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsi...

  • Page 330

    Warning! (continued) • guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel the fuel tank filler tube has a rest...

  • Page 331

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel to the vehicle when the engine is running. This is in violation of most state and federal fire regulations and may cause the mil to turn on. Note: tighten ...

  • Page 332

    Vehicle loading certification label as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle w...

  • Page 333

    Tire size the tire size on the label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim size this is the rim size that is appropriate for the tire size listed. Inflation pressure this is the cold tire inflation pressure for yo...

  • Page 334

    Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. Trailer towing in th...

  • Page 335

    Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Note: the gcwr rating includes a 150 lbs (68 kg) allowance for the presence of a driver. Gross axle weight rating (gawr) the gawr is the maximum capacity of the fr...

  • Page 336

    Hitches are the most popular on the market today and they are commonly used to tow small- and medium- sized trailers. Weight-distributing hitch a weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue...

  • Page 337

    Gooseneck hitch the gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer hitch classification your vehicle may be factory equipped for safe towing of t...

  • Page 338

    Trailer towing weights (maximum trailer weight ratings) note: for additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http:// www.Dodge.Com/bodybuilder. • http:// www.Dodge.Ca (canada). Trailer and tongue weight always load a trailer w...

  • Page 339

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to “tire safety information/tire and loading in- formation placard” i...

  • Page 340

    Warning! (continued) • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision. •...

  • Page 341

    Towing requirements – tires • do not attempt to tow a trailer while using a compact spare tire. • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation proce...

  • Page 342

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 343

    The user interface consists of the following: gain/ brake output power display shows the current gain setting. This display may also be used to display diagnostic information, if needed. • sc — short circuit to ground • sb — short to battery • cf — controller fault – if this message appears on the d...

  • Page 344

    The trailer and the vehicle’s brake lamps will come on when either vehicle braking or manual trailer brakes are applied. Trailer brake status indicator light this light indicates the trailer electrical connection status. If no electrical connection is detected after the ignition is turned on, pressi...

  • Page 345

    4. Use the gain adjustment (+/-) buttons to increase or decrease the gain setting to the desired starting point. A gain setting of 6 is a good starting point for heavier loads. 5. In a traffic-free environment, tow the trailer on a dry, level surface at a speed of 20–25 mph (30–40 km/h) and squeeze ...

  • Page 346

    Warning! The itbm module has been designed and verified for electric trailer brakes. Connecting a trailer that is not compatible with the itbm system may result in reduced or complete loss of trailer braking. There may be a increase in stopping distance or trailer instability which could result in p...

  • Page 347

    Automatic transmission the “drive” range can be selected when towing. How- ever, if frequent shifting occurs while in this range, select “tow/haul” mode (if equipped) or select a lower gear using the electronic range select (ers) feature. Note: using “tow/haul” mode or a lower gear range while opera...

  • Page 348

    Cooling system to reduce potential for engine and transmission over- heating, take the following actions: − city driving when stopped for short periods of time, shift the trans- mission into neutral and increase engine idle speed. − highway driving reduce speed. − air conditioning turn off temporari...

  • Page 349

    Before plowing • check the hydraulic system for leaks and proper fluid level. • check the mounting bolts and nuts for proper tight- ness. • check the runners and cutting edge for excessive wear. The cutting edge should be 1/4 to 1/2 in (6 cm to 1.2 cm) above ground in snow plowing position. • check ...

  • Page 350

    If necessary at the beginning and end of the snowplow season. This will help prevent uneven tire wear. The blade should be lowered whenever the vehicle is parked. Maintain and operate your vehicle and snowplow equip- ment following the recommendations provided by the specific snowplow manufacturer. ...

  • Page 351

    General maintenance snowplows should be maintained in accordance with the plow manufacturer’s instructions. Keep all snowplow electrical connections and battery terminals clean and free of corrosion. When plowing snow, to avoid transmission and drive- train damage, the following precautions should b...

  • Page 352

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models flat tow none not allowed see instructions • automatic transmission in park • manual transmission in gear (not in neutral (n) ...

  • Page 353

    Recreational towing – two-wheel drive models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is allowed only if the rear wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly...

  • Page 354

    Must be placed in gear (not in neutral) for recre- ational towing. Refer to the following for the proper transfer case neutral shifting procedure for your vehicle. Caution! • front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or r...

  • Page 355

    Shifting into neutral (n) – manual shift transfer case (if equipped) use the following procedure to prepare your vehicle for recreational towing. Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engagin...

  • Page 356

    8. Release the brake pedal (and clutch pedal on manual transmissions) for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with automatic transmission in drive or manual transmission in first gear. 10. Turn off the engine. 11. Firmly apply the parking brake. 12. Shi...

  • Page 357

    6. Shift the transfer case lever to the desired position. Note: when shifting out of transfer case neutral (n), turning the engine off may be required to avoid gear clash. 7. Shift the automatic transmission into park, or place manual transmission in neutral. 8. Release the brake pedal. 9. Disconnec...

  • Page 358

    Caution! It is necessary to follow these steps to be certain that the transfer case is fully in neutral before recre- ational towing to prevent damage to internal parts. 1. Bring the vehicle to a complete stop. Shift automatic transmission into park. 2. Turn off the engine. 3. Turn the ignition swit...

  • Page 359

    14. Shift the transmission into park or place manual transmission in gear (not in neutral). Caution! Damage to the transmission may occur if the trans- mission is shifted into park with the transfer case in neutral and the engine running. With the transfer case in neutral, ensure that the engine is ...

  • Page 360

    Shifting out of neutral – electronic shift transfer case (if equipped) use the following procedure to prepare your vehicle for normal usage: 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake. 3. Insert the key fob into the ignition ...

  • Page 361

    15. Shift the transmission into gear, release the brake pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally. Note: • steps 1 through 5 are requirements that must be met prior to pressing the transfer case neutral button and must continue to be met until the...

  • Page 363: Contents

    What to do in emergencies contents 䡵 hazard warning flasher . . . . . . . . . . . . . . . . 362 䡵 jacking and tire changing . . . . . . . . . . . . . . . 362 ▫ 3500 models — if equipped . . . . . . . . . . . . . 363 ▫ preparations for jacking . . . . . . . . . . . . . . . 364 ▫ jacking instructions ...

  • Page 364

    Hazard warning flasher the hazard warning flasher switch is located on the upper switch bank just below the radio. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press ...

  • Page 365

    3500 models — if equipped the jack and jack tools are stored under the front passenger seat. Lift the flap on the side of the seat for access. Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat. Warning! After using the jack and tools, always reinstall t...

  • Page 366

    Preparations for jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel...

  • Page 367

    Warning! (continued) • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the wheel diagonally opposite the wheel to be raised. • set the parking brake firmly and set an automatic transmission...

  • Page 368

    3. When changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube extension and wheel wrench. When changing a r...

  • Page 369

    Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. Note: if the jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. 4. ...

  • Page 370

    7. Install wheel center cap (if equipped) and remove wheel blocks. Do not install chrome or aluminum wheel center caps on the spare wheel. This may result in cap damage. 8. Lower the jack to its fully closed position. If the jack will not lower by turning the dial (thumbwheel) by hand, it may be nec...

  • Page 371

    Caution! • use a back and forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap; finish may occur. • the rear hub caps on the dual rear wheel has two pry off notches. Make sure that the hook of the jack handle driver is located squarely in ...

  • Page 372

    Slots in the wheels will assist in properly orienting the inner and outer wheels. Align these slots when assem- bling the wheels for best access to the tire valve on the inner wheel. The tires of both dual wheels must be completely off the ground when tightening to insure wheel centering and maximum...

  • Page 373

    1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 5...

  • Page 374

    Disc wheels type nut stud size torque ft lbs torque newton meters cone 9/16-18 120-150 160-200 flanged 9/16-18 130-160 190-220 to stow the flat or spare — if equipped refer to upfitters body builders guide for information on stowing your spare tire (if equipped). Hoisting a conventional floor jack m...

  • Page 375

    Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electrical system may occur. Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode ...

  • Page 376

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 377

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper c...

  • Page 378

    8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle. If frequent jump-starting is required to start your vehicle you should have ...

  • Page 379

    Caution! (continued) • when “rocking” a stuck vehicle by moving be- tween drive and reverse, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage...

  • Page 380

    Warning! • chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. Caution! Tow hooks are for emergency use only to rescue a vehicle stra...

  • Page 381

    6. Move the shift lever into the neutral position. 7. The vehicle may then be started in neutral. Towing a disabled vehicle proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equip- ment manufact...

  • Page 382

    Note: the transfer case must be in the neutral position, and the transmission must be in park (auto- matic transmission), or in gear (manual transmission) to tow a four-wheel drive vehicle, unless all its wheels are off the ground. The manufacturer recommends towing with all wheels off the ground. A...

  • Page 383: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 5.7l . . . . . . . . . . . . . 383 䡵 onboard diagnostic system (obd ii) . . . . . . . 384 ▫ loose fuel filler cap message . . . . . . . . . . . 384 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 384

    ▫ exhaust system . . . . . . . . . . . . . . . . . . . . . 397 ▫ cooling system . . . . . . . . . . . . . . . . . . . . . 399 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 404 ▫ rear axle and 4x4 front driving axle fluid level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 385

    Engine compartment — 5.7l 1 — air cleaner filter 7 — washer fluid reservoir 2 — automatic transmission dipstick 8 — integrated power module 3 — engine oil fill 9 — power steering fluid reservoir 4 — engine oil dipstick 10 — coolant pressure cap 5 — brake fluid reservoir 11 — engine coolant reservoir...

  • Page 386

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 387

    The select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). Emissions inspection and maintenance programs in some l...

  • Page 388

    4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 389

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 390

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 391

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for further informa- tion. Note: under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, w...

  • Page 392

    Engine oil viscosity (sae grade) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil fi...

  • Page 393

    Engine oil filter selection the manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high- quality filters should be used to assure most efficient service. Mopar 威 engine oil filters are a hig...

  • Page 394

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 395

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and are identified on the battery case. Cable clamps should b...

  • Page 396

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 397

    Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubri- cated periodically with a lithium based grease, such as mopar 威 spray white lube or equivalent, to assure qu...

  • Page 398

    Adding washer fluid the fluid reservoir is located under the hood and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (not ra- diator antifreeze). When refilling the washer fluid reser- voir, take some washer fluid and apply it to a clot...

  • Page 399

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 400

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions con- trol device and may seriously reduce engine per- formance and cause serious damage to the engine. • damage to the catalytic converter can r...

  • Page 401

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 402

    Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper va...

  • Page 403

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they may not be compatible with the engine coolant (antifreeze) and may plug the radiator. • this vehicle has not been designed for us...

  • Page 404

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze...

  • Page 405

    Disposal of used coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children do not store ethylene glycol-based e...

  • Page 406

    If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • do not overfill the coolant recovery bottle. • check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottl...

  • Page 407

    Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 408

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 409

    Drain and refill on 4500/5500 vehicles, remove the lower bolt to drain the axle fluid. Refer to the “maintenance schedule” for the proper maintenance intervals. Lubricant selection refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Note: the prese...

  • Page 410

    Transfer case drain and refill refer to the “maintenance schedule” for the proper maintenance intervals. Lubricant selection refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check this fluid level can be checked by removing the fille...

  • Page 411

    Caution! (continued) • using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid a...

  • Page 412

    To check the automatic transmission fluid level properly, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3. Fully apply the parking brake and press the brake pedal. 4. Place the shift lever momentari...

  • Page 413

    Caution! Be aware that if the fluid temperature is below 50°f (10°c) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission afte...

  • Page 414

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road...

  • Page 415

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder which will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty ...

  • Page 416

    Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use mopar 威 wheel cleaner or equivalent or select a nonabrasive, non-acidic...

  • Page 417

    Mopar 威 total clean or equivalent is specifically recom- mended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a dam...

  • Page 418

    Cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rearview mirror, spray cleaner on the towel...

  • Page 419

    Cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart. Cavity cartridge fuse mini fuse description j01 30 amp pink bat – presafe #1/ cm2200 j02 30 amp pink bat – trailer tow main j03 25 amp natural bat – passenger door node j04 40 amp ...

  • Page 420

    Cavity cartridge fuse mini fuse description j09 30 amp pink bat – plg/electric brake j10 40 amp green bat – l/bar/off-road j11 30 amp pink bat – sway/ thatchum/rear doors j12 40 amp green starter solenoid j13 60 amp yellow bat – rad fan #1/#2/ ssr j14 40 amp green bat – folding seat/ pzev j15 60 amp...

  • Page 421

    Cavity cartridge fuse mini fuse description m25 10 amp red bat – j1962 diag/ mirrors m26 10 amp red bat – ign sw, win, pass m27 15 amp blue bat – chmsl/brake sw m28 10 amp red bat – corax tpm/ pem/hvac htr pump m29 15 amp blue bat – folding mirror m30 25 amp natural bat – inverter m31 20 amp yellow ...

  • Page 422

    Cavity cartridge fuse mini fuse description m41 15 amp blue iod-sdars/ves 2–3/dvd/hfm/ ugdo/vanity lamp m42 10 amp red iod-hvac, u/hood lamp m43 10 amp red horn #2 m44 10 amp red ign r/s-orc/ocm m45 10 amp red ign r-orc/trail tow (bux) sense m46 20 amp yellow ign r-trail tow (bux) m47 10 amp red ign...

  • Page 423

    Caution! • when installing the totally integrated power mod- ule cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the totally integrated power module and possibly result in a electrical system failure. • when replacing ...

  • Page 424

    Note: • when reinstalling the iod fuse push firmly until fully seated; the gauges in the instrument cluster will do a full sweep when the ignition switch is turned to the run position. This is a normal condition. • when the vehicle is shipped from the factory, the iod fuse is in the up or extracted ...

  • Page 425

    Bulb replacement dual or quad headlamp/front park and turn signal – if equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the four plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges. 4. Remove the two pla...

  • Page 426

    8. Reach through the access hole of the wheel house splash shield and lift the slide lock upward far enough to disengage it from the lock post on the back of the front lamp unit housing. 9. Remove the headlamp assembly. Grasp the outboard edge of the lamp and pull it straight forward to disen- gage ...

  • Page 427

    Fog lamps – if equipped 1. Reach under and behind the front bumper to access the back of the front fog lamp housing. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise 1 ⁄ 4 turn to unlock the bulb from the housing. 4. Pull the bulb straig...

  • Page 428

    2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn the desired bulb socket 1 ⁄ 4 turn and remove the socket and bulb from housing. 4. Pull the desired bulb straight from the socket. 426 maintaining your vehicle.

  • Page 429

    Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • outside bulbs: cargo lamps • inside bulb: center high-mounted stop lamp 5. Reverse the procedure for installation of bulbs and housing. Cab...

  • Page 430

    2. Rotate the socket 1 ⁄ 4 turn and pull it from the lamp assembly. 3. Pull the bulb straight from it’s socket and replace. 428 maintaining your vehicle.

  • Page 431

    Fluid capacities u.S. Metric fuel (approximate) standard rear tank 52 gallons 197 liters optional midship tank 22 gallons 83 liters engine oil with filter 5.7l engine (sae 5w-20, api certified) 7 quarts 6.6 liters cooling system 5.7l engine (mopar 威 antifreeze/coolant 5 year/100,000 mile formula) or...

  • Page 432

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5–year/100,000 mile formula hoat (hy- brid organic additive technology) or equivalent. Engine oil – 5.7l engine use api certified sae 5w-20 engine oil, meeting the requir...

  • Page 433

    Chassis component fluid, lubricant, or genuine part automatic transmission (five-speed 545rfe) mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Transfer case mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Front and rear axle flu...

  • Page 435: Maintenance Schedules

    Maintenance schedules contents 䡵 emissions control system maintenance . . . . . . 434 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 434 ▫ 5.7l gas engine . . . . . . . . . . . . . . . . . . . . . 434 ▫ required maintenance intervals . . . . . . . . . . 436 8 m a i n t e n a n c e s c h ...

  • Page 436

    Emissions control system maintenance the scheduled maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done t...

  • Page 437

    Note: • the oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been 6 months since your last oil change even if the oil change indicator message is not illumi- nated. • change your engine oil more often if you drive your vehicle off-r...

  • Page 438

    Once a month • check tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and add as needed. • check all lights and other electri...

  • Page 439

    8,000 miles (13,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). ❏ lube the front drive shaft fitting (4x4 only). Odometer reading date rep...

  • Page 440

    24,000 miles (39,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). ❏ lube the front drive shaft fitting (4x4 only). ❏ inspect the cv joint...

  • Page 441

    32,000 miles (52,000 km) or 24 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 32,000 miles (52 000 km). ❏ replace the engine air cleaner filter. ❏ replace the spark plugs. ❏ l...

  • Page 442

    48,000 miles (78,000 km) or 36 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 48,000 miles (78 000 km). ❏ if using your vehicle for any of the following: dusty or off-road con...

  • Page 443

    64,000 miles (104,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). ❏ replace the engine air cleaner filter. ❏ replace the spark plugs. ❏...

  • Page 444

    72,000 miles (117,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ lube the front drive shaft fitting (4x4 only). ❏ inspect the cv joi...

  • Page 445

    80,000 miles (130,000 km) or 60 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 80,000 miles (130 000 km). ❏ if using your vehicle for any of the following: dusty or off-road c...

  • Page 446

    96,000 miles (156,000 km) or 72 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏ replace the engine air cleaner filter. ❏ replace the spark plugs. ❏...

  • Page 447

    104,000 miles (169,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ lube the front drive shaft fitting (4x4 only). ❏ flush and replac...

  • Page 448

    120,000 miles (195,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏ lube the front drive shaft fitting (4x4 only). ❏ inspect the cv j...

  • Page 449

    128,000 miles (208,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). ❏ replace the engine air cleaner filter. ❏ replace the spark plugs....

  • Page 450

    144,000 miles (234,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). ❏ if using your vehicle for any of the following: dusty or off-roa...

  • Page 451

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about...

  • Page 453: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453 ▫ prepare for the appointment . . . . . . . . . . . 453 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 453 ▫ be reasonable with r...

  • Page 454

    䡵 publication order forms . . . . . . . . . . . . . . . . 457 䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 459 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 459 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 4...

  • Page 455

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 456

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 457

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 458

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 459

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 460

    • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, and/or...

  • Page 461

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 462

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 463: Index

    Index 10

  • Page 464

    Adding engine coolant (antifreeze) . . . . . . . . . . 401 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 328 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . 153 air cleaner, engine (engine air cleaner filter) . . . 391 air conditioner maintenance . . . . . . . . ....

  • Page 465

    Automatic transmission adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . 410 fluid and filter changes . . . . . . . . . . . . . . . . . 411 fluid level check . . . . . . . . . . . . . . . . . . . 408,409 fluid type . . . . . . . . . . . . . . . . . . . . . . . . 408,431 shifting . . . ....

  • Page 466

    Carbon monoxide warning . . . . . . . . . . . . . . . 75,327 cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 cellular phone . . . . . . . . . . . . . . . . . . . . . . . . 91,253 center high mounted stop light . . . . . . . . . . . . 425 center lap belts . . . . . . . . . . ....

  • Page 467

    Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 403 points to remember . . . . . . . . . . . . . . . . . . . . 403 pressure cap . . . . . . . . . . . . . . . . . . . . . . . . . 402 radiator cap . . . . . . . . . . . . . . . . . . . . . . . . . 402 selection of coolant (antifreeze) ...

  • Page 468

    Tow hooks . . . . . . . . . . . . . . . . . . . . . . . . . . 377 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 emission control system maintenance . . . . . . 385,434 engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 air cleaner . . . . . . . . . . . . ...

  • Page 469

    Fluid level checks automatic transmission . . . . . . . . . . . . . . . . . 409 brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405 power steering . . . . . . . . . . . . . . . . . . . . . . . . 295 fluids, lubricants and genuine parts . . . . . . . . . . 430 fog lights . . . . . ....

  • Page 470

    Gross vehicle weight rating . . . . . . . . . . . . . . . . 332 guide, body builders . . . . . . . . . . . . . . . . . . . . . . 6 gvwr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330 hands-free phone (uconnect™) . . . . . . . . . . . . . . 91 hazard driving through flowing, rising...

  • Page 471

    Instrument cluster . . . . . . . . . . . . . . . . . . . . 182,184 instrument panel and controls . . . . . . . . . . . . . . 181 instrument panel lens cleaning . . . . . . . . . . . . . 416 integrated power module (fuses) . . . . . . . . . . . . 416 integrated trailer brake controls . . . . . . . . ...

  • Page 472

    Bulb replacement . . . . . . . . . . . . . . . . . . . 422,423 cap top clearance . . . . . . . . . . . . . . . . . . . . . 427 cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 center mounted stop . . . . . . . . . . . . . . . . . . . 425 check engine (malfunction indicator) . . ...

  • Page 473

    Lubrication, body . . . . . . . . . . . . . . . . . . . . . . . 395 lug nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . 367,369 maintenance free battery . . . . . . . . . . . . . . . . . . 392 maintenance procedures . . . . . . . . . . . . . . . . . . . 387 maintenance schedule . . . . . ...

  • Page 474

    Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390,430 filter disposal . . . . . . . . . . . . . . . . . . . . . . . . 390 identification logo . . . . . . . . . . . . . . . . . . . . . 389 materials added to . . . ....

  • Page 475

    Pregnant women and seat belts . . . . . . . . . . . . . . 51 programmable electronic features . . . . . . . . . . . . 211 programming transmitters (remote keyless entry) . . . . . . . . . . . . . . . . . . . . 20 radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . 315 radiator cap (co...

  • Page 476

    Safety, exhaust gas . . . . . . . . . . . . . . . . . . . . . . . 75 safety information, tire . . . . . . . . . . . . . . . . . . . 301 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 satellite radio antenna . . . . . . . . . . . . . . . . . 238,247 satellite radio (uconnect...

  • Page 477

    Transfer case, shifting into transfer case neutral (n) . . . . . . . . . . . . . . . . . . . . . . . 353,355 transfer case, shifting out of transfer case neutral (n) . . . . . . . . . . . . . . . . . . . . . . . 354,358 shoulder belt upper anchorage . . . . . . . . . . . . . . 48 shoulder belts . . ...

  • Page 478

    Temperature gauge, engine coolant . . . . . . . . . . 184 tether anchor, child restraint . . . . . . . . . . . . . 67,70 tilt steering column . . . . . . . . . . . . . . . . . . . . . 152 tip start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269 tire and loading information placard ....

  • Page 479

    Towing assistance . . . . . . . . . . . . . . . . . . . . . . . 105 traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . 332 cooling system tips . . . . . . . . . . . . . . . . . . . . 346 hitches . . . . . . . . ...

  • Page 480

    Voice recognition system (vr) . . . . . . . . . . . . . . 121 voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 warning lights (instrument cluster description) . . . . . . . . . . . . . 184 warnings and cautions . . . . . . . . . . . . . . . . . . . . . 6 warranty information ....

  • Page 481

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 482

    Dakota chrysler group llc o w n e r ’ s m a n u a l 2 0 1 1 2011 dakota 11 dd43-126-ad fourth edition printed in u.S.A..