RAM 2012 1500 Owner's Manual

Page 1

R a m t r u c k g a s 1 5 0 0 / 2 5 0 0 / 3 5 0 0 chrysler group llc o w n e r ’ s m a n u a l 2 0 1 2 2 0 12 r a m t r u c k g a s 1 5 0 0 /2 5 0 0 /3 5 0 0 12d241-126-aa first edition printed in u.S.A. 875256 ram truck gas om cover.Indd 1 3/16/11 4:33 pm.

Page 3: Table Of Contents

Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

Page 6

Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

Page 8

Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

Page 11: Contents

Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ wireless ignition node (win) — if equipped . . . . . . . . . . . . . . . . . . 12 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ removing key fob from ignition...

Page 13

▫ seat belt extender . . . . . . . . . . . . . . . . . . . . . 55 ▫ supplemental restraint system (srs) — air bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 ▫ air bag system components . . . . . . . . . . . . . 57 ▫ advanced front air bag features . . . . . . . . . . 58 ▫ air ba...

Page 15

Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key ...

Page 17

(evic)/personal settings (customer-programmable features)” in “understanding your instrument panel” for further information. Caution! • if your vehicle battery becomes low or dead, your key fob will become locked in the ignition. • do not attempt to remove the key fob while in this condition, damage...

Page 19

Note: a key fob that has not been programmed is also considered an invalid key. During normal operation, after turning on the ignition switch, the vehicle security light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a proble...

Page 21

Vehicle security alarm — if equipped the vehicle security alarm monitors the vehicle doors and ignition for unauthorized operation. When the ve- hicle security alarm is activated, interior switches for door locks are disabled. The system provides both au- dible and visible signals, for the first thr...

Page 23

• the illuminated entry system will not operate if the dimmer control is in the “dome defeat” position (extreme bottom position). Remote keyless entry (rke) — if equipped the rke system allows you to lock or unlock the doors and activate the panic alarm from distances up to approximately 66 ft (20 m...

Page 25

Flash lamps with remote key lock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to “...

Page 27

The panic alarm will stay on for three minutes unless you turn it off by either pressing the panic button a second time or drive the vehicle at a speed of 5 mph (8 km/h) or greater. Note: • the interior lights will turn off if you turn the ignition switch to the acc or on/run position while the pani...

Page 29

How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switch • battery at an acceptable cha...

Page 31

Note: to avoid unintentional shut downs, the system will disable the one time press of the remote start button for two seconds after receiving a valid remote start request. To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, press and release the unlock button on t...

Page 33

Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

Page 35

To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to engage and disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the u...

Page 37

The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of quad cab 威, mega cab威 and crew cab models. The windows wi...

Page 39

2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Window lockout switch — 4–door models the window lockout switch on the driver’s door allows you to disable the w...

Page 41

If you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for children (latch) feature also can be used to hold infant and child restraint systems. For more information on latch, refer to lower anchors and tether for children (latch). Note:...

Page 43

Warning! (continued) • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • supplemen...

Page 45

2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch...

Page 47

4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in an accident. War...

Page 49

Regular cab front center three point belt 1. The front center seat belt on the regular cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger ...

Page 51

Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold ...

Page 53

Warning! • a lap belt worn too loose or too high is dangerous. • a belt worn too loose can allow you to slip down and under the belt in a collision. • a belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal inju...

Page 55

Warning! • the belt and retractor assembly must be replaced if the seat belt assembly automatic locking re- tractor (alr) feature or any other seat belt func- tion is not working properly when checked ac- cording to the procedures in the service manual. • failure to replace the belt and retractor as...

Page 57

Beltalert 威 can be enabled or disabled by your authorized dealer. Chrysler group llc does not recommend deac- tivating beltalert 威. Note: although beltalert 威 has been deactivated, the seat belt reminder light will continue to illuminate while the driver’s or front passenger (if equipped with belt a...

Page 59

The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of t...

Page 61

Warning! • no objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • do not put anything on or around the air bag covers or attempt to open them manually. Y...

Page 63

• being too close to the sab and sabic air bags during deployment could cause you to be severely injured or killed. The system includes side impact sensors that are cali- brated to deploy the side air bags during impacts that require air bag occupant protection. Warning! • if your vehicle is equippe...

Page 65

Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all acci- dents, and also are needed to help keep you in position, away fr...

Page 67

Based on the severity and type of collision, the side air bag inflator on the crash side of the vehicle may be triggered, releasing a quantity of non-toxic gas. The inflating sab exits through the seat seam into the space between the occupant and the door. The sab fully inflate in about 10 milliseco...

Page 69

Bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow...

Page 71

Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of t...

Page 73

Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

Page 75

Children too large for booster seats children who are large enough to wear the shoulder belt comfortably and whose legs are long enough to bend over the front of the seat when their back is against the seatback should use the lap/shoulder belt in a rear seat. • make sure that the child is upright in...

Page 77

Lower anchors and tether for children (latch) each vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tether for children. The latch system provides for the installation of the child restraint without using the vehicle seat belt, instead ...

Page 79

Installing the child restraint system warning! Do not install child restraint systems equipped with latch mechanisms in the center position of a quad cab 威 rear seat, or crew cab model with a bench rear seat. A child may be placed in the rear center seating position of a quad cab 威, or crew cab benc...

Page 81

Installing a child restraint with an alr: 1. To install a child restraint with alr, first, pull enough of the seat belt webbing from the retractor to route it through the belt path of the child restraint. Slide the latch plate into the buckle until you hear a “click.” next, extract all the seat belt...

Page 83

Multiple child restraint installation sequence (quad cab 威/crew cab/mega cab威 - rear seats) mega cab 威 1. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat. Regular cab tether st...

Page 85

2. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint, through the outboard tether strap loop, then route it to the tether strap loop located directly behind the center rear seat. 3. Pass each tether strap hook under the head...

Page 87

Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

Page 89

Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Floor mat safety information always use floor mats designed ...

Page 91: Contents

Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 96 ▫ automatic dimming mirror — if equipped . . . 96 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 97...

Page 93

▫ automatic headlights — if equipped . . . . . . 161 ▫ headlights on with wipers (available with automatic headlights only) . . . . . . . . . . . . 162 ▫ headlight delay . . . . . . . . . . . . . . . . . . . . . 162 ▫ parking lights and panel lights . . . . . . . . . 162 ▫ fog lights — if equipped ....

Page 95

▫ using homelink威 . . . . . . . . . . . . . . . . . . . 196 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 ▫ troubleshooting tips . . . . . . . . . . . . . . . . . . 197 ▫ general information . . . . . . . . . . . . . . . . . . 198 䡵 power sunroof — if equipped . . . . . . . . ...

Page 97

䡵 slide-in campers . . . . . . . . . . . . . . . . . . . . . . 238 ▫ camper applications . . . . . . . . . . . . . . . . . . 238 䡵 easy-off tailgate . . . . . . . . . . . . . . . . . . . . . . 238 ▫ disconnecting the rear camera — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 238 ▫...

Page 99

To the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. Note: this feature is disabled when the vehicle is moving in reverse. Caution! To avoid damage to the mirror during cleaning, never spray any cleani...

Page 101

Power mirrors — if equipped the controls for the power mirrors are located on the driver’s door trim panel. The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a mirror, press either the l (left) or r (right) button to select the mirror that y...

Page 103

“slide-on-rod” features of sun visor — if equipped the sun visor “slide-on-rod” feature allows for addi- tional flexibility in positioning the visor to block out the sun. To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until...

Page 105

Uconnect™ phone — if equipped uconnect™ phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ phone al- lows you to dial a phone number with your mobile phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s a...

Page 107

Operation voice commands can be used to operate the uconnect™ phone and to navigate through the uconnect™ phone menu structure. Voice commands are required after most uconnect™ phone prompts. You will be prompted for a specific command and then guided through the available options. • prior to giving...

Page 109

Phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the uconnect™ phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at an...

Page 111

Phonebook. Specific bluetooth 威 phones with phone book access profile may support this feature. See uconnect™ website for supported phones. • to call a name from the uconnect™ phonebook or downloaded phonebook, follow the procedure in “call by saying a name” section. • automatic download and update,...

Page 113

From which you choose. To select one of the entries from the list, press the button while the uconnect™ phone is playing the desired entry and say “delete”. • after you enter the name, the uconnect™ phone will ask you which designation you wish to delete: home, work, mobile, other, or all. Say the d...

Page 115

Note: the uconnect™ phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making a second call while current call is in progress to make a second call while you are cu...

Page 117

Uconnect™ phone features language selection to change the language that the uconnect™ phone is using: • press the button to begin. • after the “ready” prompt and the following beep, say the name of the language you wish to switch to english, espanol, or francais. • continue to follow the system prom...

Page 119

Paging to learn how to page, refer to “working with automated systems”. Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the uconnect™ phone. Voice mail calling to learn how to access your voice mail, refer to “working with automate...

Page 121

Dialing using the mobile phone keypad you can dial a phone number with your mobile phone keypad and still use the uconnect™ phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth 威 mobil...

Page 123

• the selected phone will be used for the next phone call. If the selected phone is not available, the uconnect™ phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. Delete uconnect™ phone paired mobile phones • press the button to ...

Page 125

• fully closed windows, • dry weather condition. • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system such as voice mail, or when sending a page, at the...

Page 127

Send messages: you can send messages using uconnect™ phone. To send a new message: • press the button. • after the “ready” prompt and the following beep, say “sms send” or “send message.” • you can either say the message you wish to send or say “list messages.” there are 20 preset messages. To send ...

Page 129

3 understanding the features of your vehicle 127.

Page 131

3 understanding the features of your vehicle 129.

Page 133

Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

Page 135

If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system is speaking is known as “barging in.” the system will be interrupted, and after the beep, you can add or chan...

Page 137

• “menu radio” (to switch to the radio menu) • “main menu” (to switch to the main menu) satellite radio to switch to satellite radio mode, say “sat” or “satellite radio”. In this mode, you may say the following com- mands: • “channel number” (to change the channel by its spoken number) • “next chann...

Page 139

Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect™ voice “voice training” feature may be used. 1. Press the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your...

Page 141

Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting the seat up or down the height of the seats...

Page 143

Warning! (continued) • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a col...

Page 145

Note: • once a heat setting is selected, heat will be felt within two to five minutes. • the engine must be running for the heated seats to operate. The heated seats switch from high to low and from low to off automatically, based on time and tempera- ture of the seat. The heated seats can operate o...

Page 147

Press the switch once to choose high, press it a second time to choose low. Pressing the switch a third time will turn the ventilated seat off. When high speed is selected both lights on the switch will be illuminated. When low speed is selected one light will be illuminated. Note: the engine must b...

Page 149

To adjust the seatback, lift upward on the handle, lean back on the seatback and when you reach the desired position, release the handle. To return the seatback, lift upward on the handle, lean forward and release the handle at the desired position. Warning! Do not ride with the seatback reclined so...

Page 151

2. Fold the seatback forward. 3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place. Folding rear seat — if equipped both the outboard rear seats will drop and move forward when the seatback is folded flat. Table mode handle table mode 3 understand...

Page 153

3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place. Warning! An improperly latched seat could cause serious in- jury or death. Make sure that the seatback is securely locked into position. If the seatback in not securely locked into position the sea...

Page 155

Rear head restraints the two outboard seat are equipped with adjustable head restraints. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the adjustment button, located on the base of the head restraint, and push downward on the head restraint. Note:...

Page 157

1. Insert the ignition key, and turn the ignition switch to the on/run position. 2. Press the driver door memory button number 1 if you are setting the memory for driver 1, or button number 2 if you are setting the memory for driver 2. The system will recall any stored settings. Wait for the system ...

Page 159

5. Within five seconds, press and release the unlock button on the rke transmitter. To disable another rke transmitter linked to either memory position, repeat steps 1 through 5 for each rke transmitter. Note: once programmed, all rke transmitters linked to memory can be easily enabled or disabled a...

Page 161

2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, before raising the hood. Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latc...

Page 163

Headlights to turn on the headlights, rotate the headlight switch clockwise to the headlight position. When the headlight switch is on, the parking lights, taillights, license plate light and instru- ment panel lights are also turned on. To turn off the headlights, rotate the headlight switch back t...

Page 165

The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pushed a second time, when the headlight sw...

Page 167

Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is opened. Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. I...

Page 169

High/low beam switch push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off. Windshield wipers and washers windshield wipers the wipers and wa...

Page 171

Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist feature when...

Page 173

The heated steering wheel switch is located on the switch bank below the climate controls. Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on. Pressing the switch a second time will turn off the heated steering w...

Page 175

Warning! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked. Electronic speed control when engaged, the electronic speed control takes over accelerator operations at speeds greater than 25 mph (40 km...

Page 177

To resume speed to resume a previously set speed, push the res (+) button and release. Resume can be used at any speed above 20 mph (32 km/h). To vary the speed setting when the electronic speed control is set, you can in- crease speed by pushing the res (+) button. If the button is continually pres...

Page 179

Parksense 姞 sensors the four parksense 威 sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 in (30 cm) up to 79 in (200 cm) from the rear fascia/bumper in the horizontal di...

Page 181

Slow tone fast tone 3 understanding the features of your vehicle 179.

Page 183

Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none single 1/2 second tone slow fast continuous display message park assist system on warning object detected warning object de...

Page 185

Cleaning the parksense 姞 system clean the parksense 威 sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. Parksense 姞 system usage precautions note: • ensure that the rear bumper is free o...

Page 187

Warning! • drivers must be careful when backing up even when using the parksense 威 rear park assist sys- tem. Always check carefully behind your vehicle, look behind you, and be sure to check for pedes- trians, animals, other vehicles, obstructions, and blind spots before backing up. You are respons...

Page 189

Warning! Drivers must be careful when backing up even when using the parkview 威 rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your...

Page 191

Courtesy/reading lights both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the unlock button is pressed on the remote keyless ent...

Page 193

Note: homelink 威 is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink 姞 be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is rec...

Page 195

3. Simultaneously press and hold both the homelink 威 button you want to program and the hand-held transmit- ter button. 4. Continue to hold buttons until the evic display changes from “channel # training” to “chan- nel # trained”, then release both buttons. Note: • it may take up to 30 seconds or lo...

Page 197

5. Press and hold the programmed homelink 威 button. The evic will display “channel # transmit”. If the garage door opener/device activates, programming is complete. To program the remaining two homelink 威 buttons, repeat each step for each remaining button. Do not erase the channels. Reprogramming a...

Page 199

Security it is advised to erase all channels before you sell or turn in your vehicle. To erase the channels press and hold the two outside homelink 威 buttons (i and iii) for up 20 seconds. The electronic vehicle information center (evic) will display “clearing channels”. Release the buttons when the...

Page 201

Power sunroof — if equipped the power sunroof switch is located on the overhead console between the courtesy/reading lights. Warning! • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fata...

Page 203

Venting sunroof — express press and release the “vent” button, and the sunroof will open to the vent position. This is called “express vent”, and will occur regardless of sunroof position. During express vent operation, any movement of the switch will stop the sunroof. Sunshade operation the sunshad...

Page 205

• inside the top storage tray — with floor mounted shifter. • inside the upper lid of the center storage compartment — if equipped. Power outlet — floor shifter power outlet — upper lid 3 understanding the features of your vehicle 203.

Page 207

Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

Page 209

For vehicles equipped with an optional floor shifter. Power inverter — if equipped a 115 volt (150 watts maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power u...

Page 211

The power inverter switch is located on the switch bank below the climate controls. To turn on the power outlet, press the switch once. Press the switch a second time to turn the power outlet off. Note: • when the power inverter switch is pressed, there will be a delay of approximately one second be...

Page 213

Front instrument panel cupholders — floor mounted shifter for vehicles equipped with bucket seats and a floor mounted shifter there are two cupholders located in the floor console. Rear cupholder — quad cab 姞 quad cab 威 vehicles may be equipped with a rear cup- holder that consists of two cup wells ...

Page 215

To open the upper glove box push upward on the handle release. The glove box door will automatically open. To open the lower glove box, pull on the handle to release the latch and lower the door. Upper glove box lower glove box 3 understanding the features of your vehicle 213.

Page 217

Center storage compartment — if equipped the center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Warning! • this armrest is not a seat. Anyone seated on the armrest could be seri...

Page 219

Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injur...

Page 221

Storage and seats (crew cab) the crew cab models provide additional storage under the rear seats. Lift the seats to access the storage com- partment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Caution! Always lift the storage compartment lids by using ...

Page 223

Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

Page 225

2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3. Reverse the procedure to store the load floor. Positioning the load floor for storage access under the seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap locat...

Page 227

Rambox 姞 integrated box side storage bins cargo storage bins are located on both sides of the pickup box. The cargo storage bins provide watertight, lockable, illuminated storage for up to 150 lbs (68 kg) of evenly distributed cargo. Caution! Failure to follow the following items could cause damage ...

Page 229

Caution! Leaving the lid open for extended periods of time could cause the vehicle battery to discharge. If the lid is required to stay open for extended periods of time, it is recommended that the bin lights be turned off manually using the on/off switch. The rambox 威 storage bins can be locked usi...

Page 231

Note: in the event of an individual being locked inside the storage bin, the storage bin cover can be opened from inside of the bin by pulling on the glow-in-the-dark lever attached to the storage bin cover latching mechanism. Bed extender — if equipped the bed extender has three functional position...

Page 233

5. Lock the center handle using the vehicle key to secure the panel into place and assist against theft. Divider position the divider position is intended for managing your cargo and assisting in keeping cargo from moving around the bed. There are 11 divider slots along the bed inner panels which al...

Page 235

4. Rotate the center handle horizontally to secure the side gates in the closed position. 5. Lock the center handle to secure the panel into place and assist against theft. Extender position the extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add...

Page 237

Warning! To reduce the risk of potential injury or property damage: • cargo must be secured. • do not exceed cargo load rating of your vehicle. • secure all loads to truck utilizing cargo tie downs. • extender should not be used as cargo tie down. • when vehicle is in motion do not exceed 150 lbs (6...

Page 239

Out on the cleat and slide it to the detent nearest the desired location. Make sure the cleat is seated in the detent and tighten the nut. To remove the cleats from the utility rail, remove the end cap by pushing up on the locking tab, located on the bottom of the end cap. Slide the cleat off the en...

Page 241

3. Disconnect the chassis wiring harness, ensuring the connector bracket does not fall into the sill. 4. Connect the chassis plug and bracket (provided in the glove box) to the chassis wiring harness and insert the bracket back into the sill. 5. Connect the tailgate plug (provided in the glove box) ...

Page 243: Contents

Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 245 䡵 switch bank button description . . . . . . . . . . . 246 ▫ upper switch bank . . . . . . . . . . . . . . . . . . . 246 ▫ lower switch bank . . . . . . . . . . . . . . . . . . . 247 䡵 instrume...

Page 245

䡵 ipod威/usb/mp3 control — if equipped . . . . . 314 ▫ connecting the ipod威 or external usb device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ using this feature . . . . . . . . . . . . . . . . . . . 316 ▫ controlling the ipod威 or external usb device using radio buttons . . . . . . ...

Page 247

Instrument panel features 1 — headlight switch 7 — 115v power inverter outlet 13 — transfer case position switch 2 — instrument cluster 8 — power outlet 14 — ignition switch 3 — radio 9 — lower switch bank 15 — hood release 4 — upper switch bank 10 — cup holders 16 — parking brake release 5 — upper ...

Page 249

Lower switch bank the lower switch bank is located on the center of the instrument panel. 1. Heated seats refer to “understanding the features of your vehicle” for more information. 2. Ventilated seats refer to “understanding the features of your vehicle” for more information. 3. Heated steering whe...

Page 251

Instrument cluster — premium 4 understanding your instrument panel 249.

Page 253

Caution! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear cont...

Page 255

9. 4wd auto indicator the 4wd auto indicator will be illuminated whenever the four-wheel drive mode is auto- matically engaged. 10. Svc (service) 4wd the svc 4wd light monitors the electric shift four-wheel drive system. If the svc 4wd light stays on or comes on during driving, it means that the fou...

Page 257

16. Odometer display / electronic vehicle information center (evic) display area — if equipped odometer display the odometer display shows the total distance the ve- hicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser t...

Page 259

A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). Low tire when the appropriate condition exists, the odometer display will toggle between lo and tire for three cycles. Nofuse if the vehicle diagnostic system determines that the ignitio...

Page 261

19. Low fuel light when the fuel level reaches approximately 3.0 gal (11.0 l) this light will turn on, and remain on until fuel is added. For vehicles equipped with a premium cluster this indi- cator will display in the electronic vehicle information center (evic). Refer to ”electronic vehicle infor...

Page 263

Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the abs, are also equipped with electronic brake force dist...

Page 265

Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and...

Page 267

Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to...

Page 269

31. Seat belt reminder light when the ignition switch is first turned to on/ run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s seat belt rema...

Page 271

• customer programmable features (system setup) • trip information (in odometer line) press and release the up button to scroll upward through the main menus and sub- menus. Press and release the down button to scroll downward through the main menus and sub- menus. Select button press and release th...

Page 273

• remote start aborted — fuel low • remote start active — key to run • remote start disabled — system fault • system setup unavailable — vehicle in motion (manual transmission) • remote start disable — start vehicle to reset • service four wheel drive system • clean park assist sensors • front park ...

Page 275

• electronic speed control light this light will turn on when the electronic speed control is on. • electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. The light will come on when the ignition is first turned on and remain on...

Page 277

• loose gascap indicator if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the telltale display area. Tighten the fuel filler cap properly and press the select button to turn off the message. If t...

Page 279

Distance to empty (dte) distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. Dte cannot be re...

Page 281

Tire psi press and release the up or down button until “tire psi” displays in the evic and press the select button. This will display the tire pressure monitor system (shows the current pressure of all four road tires). For additional information, refer to “tire pressure monitor system” in “starting...

Page 283

Note: a good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Manual compass calibration if the compass appears erratic and the cal indicator does not appear in the evic display, you must pu...

Page 285

Press and release the up or down button until system setup displays in the evic. Press the select button to enter the system setup sub-menu. Use the up or down button to display one of the following choices. Select language when in this display you may select one of five lan- guages for all display ...

Page 287

Seat features will automatically turn on when tempera- tures are below 40° f (4.4° c). When temperatures are above 80° f (26.7° c) the driver vented seat will turn on when remote start is activated. These features will stay on through the duration of remote start or until the key is turned to run. T...

Page 289

Been deactivated. When this feature is deactivated, the system reverts to the standard intermittent wiper operation. Easy entry/exit seat — if equipped when this feature is selected it provides automatic driver seat positioning to enhance driver mobility when enter- ing and exiting the vehicle. To m...

Page 291

Media center 730n/430/430n (rhr/rer/rbz/ rhb) cd/dvd/hdd/nav — if equipped note: the sales code is located on the lower right side of the unit’s faceplate. Refer to your uconnect™ multimedia rhr, rer, rbz or rhb user’s manual for detailed operating instructions. Operating instructions (voice command...

Page 293

4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the ...

Page 295

Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

Page 297

Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek button to move to the next ran- domly selected track. Press the ...

Page 299

Playlist files are not supported. Mp3 pro files are not supported. Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading time...

Page 301

Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the o...

Page 303

Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either am or fm frequencies. Tune control turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decre...

Page 305

By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

Page 307

Caution! • this cd player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • the res media center is a single cd player. Do not attempt to insert a second c...

Page 309

• maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. With a maximum number of files, exce...

Page 311

List button (cd mode for mp3 play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that folde...

Page 313

Using the tune/scroll control knob until sirius id is selected. Press the tune/scroll control knob and the sirius id number will display. The sirius id number display will time out in two minutes. Press any button on the radio to exit this screen. Selecting uconnect™ multimedia (satellite) mode pres...

Page 315

If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset channel. Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button ...

Page 317

Note: the glove compartment will have a position where the ipod 威 or consumer electronic audio device cable can be routed through without damaging the cable when closing the lid. This allows routing of the cable without damaging it while closing the lid. If a cut out is not available in the glove co...

Page 319

• jump backward in the current track by pressing and holding the rw button. Holding the rw button long enough will jump to the beginning of the current track. • jump forward in the current track by pressing and holding the ff >> button. • a single press backward rw or forward ff >> will jump backwar...

Page 321

• preset 6 – podcasts • pressing a preset button will display the current list on the top line and the first item in that list on the second line. • to exit list mode without selecting a track, press the same preset button again to go back to play mode . • list button: the list button will display t...

Page 323

Uconnect™ multimedia video entertainment system (ves)™ — if equipped getting started • screen located in the overhead console : unfold the overhead lcd screen by pushing the button on the overhead console behind the screen. • with the ignition switch in the on or acc position, turn the radio on by p...

Page 325

Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list appears on the right side of the screen, touch the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 so...

Page 327

Play video games connect the video game console to the auxiliary rca input jacks located on the back of the center console. When connecting an external source to the aux input, be sure to follow the standard color coding for the ves™ jacks: note: certain high-end video games, such as playsta- tion3 ...

Page 329

3. Touch the 1 or 2 based on the headphone channel you want to change. To exit press the back arrow soft-key at the top of the screen. Listen to an audio source on channel 2 while a video is playing on channel 1 ensure the remote control and headphone switch is on channel 2. Using the remote control...

Page 331

3. To listen to an audio source on channel 2 while a video is playing on channel 1, touch the 2 soft-key and choose an audio source. To exit touch the back arrow soft-key at the top left of the left screen. Important notes for single video screen system • ves™ is able to transmit two channels of ste...

Page 333

Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 or 2 soft-key based on the ch...

Page 335

The channel 2, position the remote controls the function- ality of headphone channel 2 (left side of the screen). 5. 䉴䉴 – in radio modes, press to seek the next tunable station. In disc modes, press and hold to fast forward through the current audio track or video chapter. In menu modes use to navig...

Page 337

Locking the remote control all remote control functionality can be disabled as a parental control feature. • to disable the remote control from making any changes, press the video lock button add follow the radio’s instructions (select menu, rear ves, lock). If the vehicle is not equipped with a dvd...

Page 339

Controls the headphone power indicator and controls are located on the right ear cup. Note: the rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video sys...

Page 341

Nature whatsoever. Some states and jurisdictions may not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights, which vary from jurisdiction to jurisdiction...

Page 343

5. Channel 2 shared status 6. Channel 2 audio only/mute 7. Channel 1 enter button action 8. Channel 2 enter button action 9. Clock 10. Video lock 11. Not available / error 12. Disc changer status numeric keypad menu numeric keypad menu 4 understanding your instrument panel 341.

Page 345

Disc menu when listening to a cd audio or cd data disc, pressing the remote control’s menu button displays a list of all commands which control playback of the disc. Using the options you can activate or cancel scan play and random play. Display settings when watching a video source (dvd video with ...

Page 347

Disc formats the ves™ dvd player is capable of playing the follow- ing types of discs (12 mm or 8 mm diameter): • dvd-video discs (mpeg-2 video compression) (see notes about dvd region codes) • dvd-audio discs (2 channel audio output only) • audio compact discs (cds) • cd data discs with mp3 and wma...

Page 349

End with the extension ⬙.Mp3⬙ or ⬙.Mp3⬙ and wma files must always end with the extension ⬙.Wma⬙ or ⬙.Wma⬙. To prevent incorrect playback, do not use these extensions for any other types of files. • for mp3 files, only version 1 id3 tag data (such as artist name, track title, album, etc.) are support...

Page 351

All of the language settings have a special ⬙other⬙ setting to accommodate languages other than japanese or eng- lish. These languages are selected using a special four- digit code. To enter a new language code, activate the dvd setup menu. To enter dvd setup menu stop the dvd, enter radio disc mode...

Page 353

To set the password, activate the dvd setup menu and follow these additional instructions: • using the remote control left and right cursor but- tons, select the rating tab. • highlight ⬙change password⬙, and then press the remote control’s enter button. • enter the current password. Select a digit,...

Page 355

• using the remote control’s up and down cursor buttons, select the new rating level, and then press the remote control’s enter button to accept the change. Product agreement this product incorporates copyright protection technol- ogy that is protected by u.S. Patents and other intellec- tual proper...

Page 357

The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pre-set pushbuttons. Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginnin...

Page 359

Dials and inner push knobs. These comfort controls can be set to obtain desired interior conditions. Front blower control there are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control ...

Page 361

Mix mode air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort, while reducing moisture on the windshield. Defrost mode air is directed thr...

Page 363

Max a/c for maximum cooling, when max a/c is selected the a/c is turned on automatically and the air is recircu- lated. Note: a/c cannot be deselected when in max a/c position. The led will blink three times if the a/c button is pushed. Automatic temperature control (atc) — if equipped • the automat...

Page 365

Automatic operation 1. Position the mode control knob to the auto position on the automatic temperature control (atc) panel. 2. Position the blower control knob in the auto posi- tion on the atc panel. 3. Next, adjust the temperature you would like the system to maintain by adjusting the driver and ...

Page 367

Floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix mode air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while k...

Page 369

Vacation/storage any time you store your vehicle or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in fresh air with the blower setting in high. This will ensure adequate system lubrication to minimize the possibility of ...

Page 371: Starting And Operating

Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 375 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 375 ▫ automatic transmission . . . . . . . . . . . . . . . 375 ▫ extreme cold weather (below –20°f or ⫺29°c) . . . . . . . . . . . . . . . 376...

Page 373

䡵 driving on slippery surfaces . . . . . . . . . . . . . 451 ▫ acceleration . . . . . . . . . . . . . . . . . . . . . . . . 451 ▫ traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 452 䡵 driving through water . . . . . . . . . . . . . . . . . 452 ▫ flowing/rising water . . . . . . . . . ...

Page 375

䡵 snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . 513 䡵 tire rotation recommendations . . . . . . . . . . . 514 ▫ directional tires – if equipped . . . . . . . . . . . 515 ▫ dual rear wheels – if equipped . . . . . . . . . 515 䡵 tire pressure monitor system (tpms) . . . . . . . 516 ▫ ...

Page 377

Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Warnin...

Page 379

Warning! (continued) • if the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly. Refer to “jump starting” in “what to do in emergen- cies” for further informa...

Page 381

Warning! • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, and remove the key fob. Once the key f...

Page 383

The transmission shift lever has only park, reverse, neutral, and drive shift positions. Manual down- shifts can be made using the electronic range select (ers) shift control (described later in this section). Press- ing the ers (-/+) switches (column shift) or moving the shift lever to the left or ...

Page 385

Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

Page 387

Range of torque converter clutch engagement. This is done to prevent transmission damage due to overheat- ing. If the transmission becomes extremely hot, the “trans- mission temperature warning light” may illuminate and the transmission may downshift out of overdrive until the transmission cools dow...

Page 389

To exit ers mode, simply press and hold the shift lever to the right (+) (console shift) or the ers (+) switch (column shift) until “d” is once again displayed in the shift lever position indicator in the instrument cluster. Column shift lever console shift lever 5 starting and operating 387.

Page 391

Haul mode. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in tow/haul mode, the transmission will downshift into third gear. Note: tow/haul mode locks out overdrive. The “tow/haul indicator light” will illumina...

Page 393

Shift) while in the drive position will select the highest available transmission gear, and will display that gear in the instrument cluster as 6, 5, 4, 3, 2, 1. Gear ranges do not race the engine when shifting from park or neutral into another gear range. Park this range supplements the parking bra...

Page 395

Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

Page 397

If the transmission operating temperature exceeds normal operating limits, the powertrain controller will modify the transmission shift schedule and expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating. If the transmission becomes ext...

Page 399

Use of ers (or tow/haul mode) also enables an additional underdrive gear which is not normally used during through-gear accelerations. This additional gear can improve vehicle performance and cooling capability when towing a trailer on certain grades. In ers mode, gears 1 though 3 are underdrive gea...

Page 401

Overdrive operation the automatic transmission includes an electronically controlled overdrive (fourth and fifth gears). The trans- mission will automatically shift into the overdrive gear if the following conditions are present: • the shift lever is in the drive position, • the transmission fluid h...

Page 403

Six–speed automatic transmission (5.7l engine) — 2500 models only the shift lever position display (located in the instrument panel cluster) indicates the transmission gear range. The shift lever is mounted on the right side of the steering column. You must press the brake pedal to move the shift le...

Page 405

Warning! (continued) • it is dangerous to move the shift lever out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone ...

Page 407

Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

Page 409

To operate. Limp home mode allows the vehicle to be driven to an authorized dealer for service without dam- aging the transmission. In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following steps: 1. Stop the vehicle. 2. Shift the tran...

Page 411

Overdrive operation the automatic transmission includes an electronically controlled overdrive (fifth and sixth gears). The trans- mission will automatically shift into the overdrive gear if the following conditions are present: • the shift lever is in the drive position, • the transmission fluid ha...

Page 413

Four-wheel drive operation — if equipped four-wheel drive trucks are equipped with either a manually shifted transfer case or an electronically shifted transfer case. Refer to the operating instructions for your transfer case, located in this section for further informa- tion. Manually shifted trans...

Page 415

2h rear-wheel drive high range - this range is for normal street and highway driving on dry hard surfaced roads. 4h four-wheel drive high range - this range locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. Additional traction for loose, sli...

Page 417

This electronically shifted transfer case provides four mode positions: • two-wheel drive high range (2wd) • four-wheel drive lock range (4wd lock) • four-wheel drive low range (4wd low) • neutral (neutral) this electronically shifted transfer case is designed to be driven in the two-wheel drive pos...

Page 419

The “svc 4wd warning light” monitors the electronic shift four-wheel drive system. If this light remains on after engine start up or illuminates during driving, it means that the four-wheel drive system is not function- ing properly and that service is required. Warning! Always engage the parking br...

Page 421

Shifting procedure note: • if any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The position indicator light for the previous position will remain on and the newly selected posi- tion indicator light will continue to flash until all t...

Page 423

• the ignition switch must be in the on position for a shift to take place and for the position indicator lights to be operable. If the ignition switch is not in the on position, the shift will not take place and no position indicator lights will be on or flashing. Electronically shifted transfer ca...

Page 425

Transfer case position indicator lights the transfer case position indicator lights (4wd, 4low, and 4wd auto) are located on the instrument cluster and indicate the current and desired transfer case selection. When you select a different transfer case posi- tion, the position indicator lights will d...

Page 427

For additional information on the appropriate use of each transfer case mode position, see the information below: 2wd rear-wheel drive high range - this range is for normal street and highway driving on dry hard surfaced roads. 4wd auto four-wheel drive auto range - this range sends power to the rea...

Page 429

2. Shift the transmission into neutral. 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is on (not flashing), shift the transmission back into gear. Alternate procedure 1. Bring the vehicle to complete stop. 2. Wi...

Page 431

Position, the rear axle is locked. In the front/rear lock position, the front and rear axles are locked. Note: even when the axles are in the axle unlock position, the limited slip differential in the rear axle still provides torque biasing capability for moderate low traction environments. During t...

Page 433

The switch has two positions; on-road and off-road. The system is normally in the on-road mode, indicated by a solid green light. The stabilizer/sway bar should remain in the on-road mode during normal driving conditions. Warning! Do not disconnect the stabilizer bar and drive on hard surfaced roads...

Page 435

(orv) trails or recreation areas. You should always tread lightly and only use established roads, trails or orv recreational areas. The national forest service, bureau of land management or local department of natural re- sources are a wealth of information and usually have maps with marked trails. ...

Page 437

Warning! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When to use low range when driving off-road, shift into 4l (low range) for additional traction or to improve handling and control on slippery or difficult terrain. Due to t...

Page 439

Caution! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneu- vers. Crossing obstacles (rocks and other high points) while driving off road, you...

Page 441

Accelerator to avoid spinning the log out from under your tires. Then ease the vehicle off the log using your brakes. Caution! Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high centered. Getting high centered if you get hung up or...

Page 443

Ability to proceed then make sure you are in 4l (low range) with the transmission in first gear (manually select first gear on automatic transmissions) and pro- ceed with caution. Allow engine braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock. Warn...

Page 445

Caution! Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components and your brakes will be less effective once wet and/or mudd...

Page 447

Form to the ground contour. Different terrain, tires, and vehicles require different tire pressure. Hard surfaces like rock and heavier vehicles require higher pressures than softer surfaces such as sand and lighter vehicles. You will need to experiment to determine what is right for your situation....

Page 449

Caution! Damage can occur when spinning your tires at an excessive high speed. Do not spin your tires faster than an indicated 35 mph (56 km/h). • using the tow hooks with a tow strap – tow straps are a quick and easy way to recover your vehicle from minor situations if you have a secondary vehicle ...

Page 451

As you power the winch in. Be careful not to allow slack in the cable as you recover the vehicle. Do not try to guide the cable into the drum. If it starts to bunch up on one end, let it. You can re-spool the cable afterwards. Never use a winch cable as a tow strap and always stand back while winchi...

Page 453

Warning! On vehicles equipped with a limited-slip differential never run the engine with one rear wheel off the ground since the vehicle may drive through the rear wheel remaining on the ground. You could lose control of the vehicle. Care should be taken to avoid sudden accelerations when both rear ...

Page 455

Shallow standing water although your vehicle is capable of driving through shallow standing water, consider the following caution and warning before doing so. Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the...

Page 457

Always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiato...

Page 459

Low voltage interrupt your winch is equipped with a device that will interrupt winch function if the vehicle charging system voltage drops to a low level. The winch will not power-in or out for 30 seconds if this device is tripped. If the interrupt is tripped, the vehicle should be operated at high ...

Page 461

1. Motor: the winch motor is powered by the vehicle charging system and features a thermal protection switch that automatically stops motor function in the power-in direction if the motor gets too hot. 2. Remote socket: the remote socket allows the remote control to be attached to the control pack t...

Page 463

Clevis/d-shackles: the d-shackle is a safe means of connecting the looped ends of cables, straps and snatch blocks. The shackle’s pin is threaded to allow easy re- moval. Tree trunk protector: typi- cally made of tough, high- quality nylon, it provides the operator an attachment point for the winch ...

Page 465

3. Use the right equipment for the situation. 4. Always wear leather gloves and do not allow the wire rope to slip through your hands when handling the rope. 5. Only the operator should handle the wire rope and remote control. 6. Think safety at all times. Vehicle recovery using the winch caution! •...

Page 467

4. Free the winch hook and attach the hook strap. Free the winch hook from its anchor point. Attach the hook strap to the hook (if not attached). Free spool hook strap 5 starting and operating 465.

Page 469

Caution! Always be certain the anchor you select will with- stand the load. Note: how to choose an anchor point: a secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural an- chors include trees, stumps and rocks. Hook the cable as low as pos...

Page 471

11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure. 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope. 5 starting and operating 469.

Page 473

For additional assistance, the winched vehicle can be slowly driven while being pulled by the winch. Continue pulling until the vehicle is on stable ground. If you are able to drive the vehicle, the winching operation is complete. Note: • avoid overheating the winch motor. For extended winching, sto...

Page 475

Note: how to spool under no load: arrange the remote control lead so it cannot be caught in the winch. Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered. Tighten and straighten the layer if necessa...

Page 477

All winching operations should have a straight line from the winch to the object being pulled. This minimizes the wire rope collecting on one side of the drum affecting pulling efficiency and damaging wire rope. A snatch block, secured to a point directly in front of the vehicle will enable you to c...

Page 479

Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Power steering fluid check checking the power steering fluid level at a define...

Page 481

Note: • when the parking brake is applied and the transmis- sion is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that the park...

Page 483

Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes anti-lock brake sys- tem (abs), traction control system (tcs), brake assist system (bas), hill start assist (hsa), electronic stability control (esc) and trailer sway control (tsc)...

Page 485

Warning! • the bas cannot prevent the natural laws of phys- ics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the bas cannot prevent collisions, including those resulting from exces...

Page 487

Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision w...

Page 489

The intended path, esc applies the brake of the appro- priate wheel to assist in counteracting the oversteer or understeer condition. • oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • understeer - when the vehicle is turning less than appropriate for ...

Page 491

And the “esc off” message will appear in the odometer. Press and release the trip odometer button located on the instrument cluster to clear this message. Note: the “esc off” message will display and the audible chime will sound when the shift lever is placed into the park position from any other po...

Page 493

Trailer sway control (tsc) – if equipped the tsc system uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appro- priate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appropriate wheel(s) to counteract the sw...

Page 495

Compact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Ex- ample: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing chart...

Page 497

Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

Page 499

Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire and loading information placard this placard tells you important information about the: ...

Page 501

3. Subtract the combined weight of the driver and pas- sengers from xxx lbs or xxx kg. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the ...

Page 503

Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

Page 505

Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire infl...

Page 507

Spare tire matching original equipped tire and wheel – if equipped your vehicle may be equivalent with a spare tire and wheel in look and function as the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehic...

Page 509

Your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than ...

Page 511

Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold ...

Page 513

Tire chains use “class s” chains, or other traction aids that meet sae type “s” specifications. Use “class u” chains on 2500/3500 model trucks, or other traction aids that meet sae type “u” specifica- tions. Note: chains must be the proper size for the vehicle as recommended by the chain manufacture...

Page 515

Caution! Do not use tire chains on the front wheels of any model except for 3500 drw (dual rear wheel) trucks equipped with lt235/80r17 tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle. Do not use tire chains on the rear wheels o...

Page 517

Directional tires – if equipped for the r/t package with 22” tires & wheels, tire rotation must be performed with consideration of the tire rotation direction. The recommended rotation pattern for direc- tional tires is shown below. Dual rear wheels – if equipped the tires used on dual wheel assembl...

Page 519

The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire. The tpms will continue to warn the driver of low tire pressure as long as the condition e...

Page 521

• seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system the tire pressure monitor system (tpms) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wh...

Page 523

Premium system – if equipped the tire pressure monitor system (tpms) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the receiver module. Note: it is particu...

Page 525

Should this occur, you should stop as soon as possible and inflate the tires with a low pressure condition (those flashing in the evic graphic) to the vehicle’s recom- mended cold placard pressure inflation value. Once the system receives the updated tire pressures, the system will automatically upd...

Page 527

Vehicles with full size spare 1. The matching full size spare wheel and tire assembly has a tpm sensor that can be monitored by the tpms. 2. If you install the full size spare in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition switch cycle, a chi...

Page 529

Tire light load inflation switch operation – if equipped • this vehicle may have different recommended tire pressure values between the front and rear tires as shown in both the tire loading information label and the supplemental tire pressure information label. It is also equipped to be driven with...

Page 531

To switch back to the max load inflation pressure (cold) low pressure warning threshold, press the tire light load inflation switch. It is not necessary to first fill the tires to the max load inflation pressure (cold) values to switch the tpms system to the max load inflation pressure (cold) low pr...

Page 533

Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” reformulated gasolines contain oxygenates and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of ref...

Page 535

Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost. There- fore, you should not have to add anything to the fue...

Page 537

Caution! Only vehicles with the e-85 fuel filler door label can operate on e-85. E-85 fuel cap e-85 badge 5 starting and operating 535.

Page 539

• some additives used in regular gasoline are not fully compatible with e-85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as mopar 威 injector cleanup or techron may be used. Selection of engine oil...

Page 541

Note: when removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler door. Caution! • damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • a poorly fitting gas cap could let impurities into the...

Page 543

Gross axle weight rating (gawr) the gawr is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the gawr of each axle is not exceeded. Each axle gawr is determined by the components in the system with the lowest load carrying capacity (axl...

Page 545

Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load ...

Page 547

Equalizing) hitch are recommended for heavier tongue weights (tw) and may be required depending on vehicle and trailer configuration/loading to comply with gawr requirements. Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability and braking performance and...

Page 549

Gooseneck hitch the gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer hitch classification the following chart provides the industry standard for th...

Page 551

Ram 1500 4x4 st slt/outdoorsman/sport laramie 4.7l v-8 6–speed automatic transmission towing: 5,000 lbs (2268 kg) - std 7,400 lbs (3356 kg) - max payload: 1,540 lbs (698 kg) - max towing: 5,000 lbs (2268 kg) - std 7,450 lbs (3379 kg) - max payload: 1,560 lbs (708 kg) - max — 5.7l hemi 威v-8 6–speed a...

Page 553

Note: for additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http://www.Ramtrucks.Com. • http://www.Ramtruck.Ca (canada). Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This ...

Page 555

Warning! (continued) • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision. •...

Page 557

Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

Page 559

Manual brake control lever slide the manual brake control lever to the right to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes. If the manual brake control lever is activated while the brake is also applied, the greater of the two inputs determines the power ...

Page 561

6. Press the select button and then press the up or down buttons until the proper trailer brake type appears on the screen. Note: 1500 models only – light electric and heavy electric will only be available due to the tow capacities of the vehicle. 7. Use the gain adjustment (+/-) buttons to increase...

Page 563

Compatible with itbm. To determine the type of brakes on your trailer and the availability of control- lers, check with your trailer manufacturer or dealer. • removal of the itbm will cause errors and it may cause damage to the electrical system and electronic modules of the vehicle. See your author...

Page 565

Note: using “tow/haul” mode or a lower gear range while operating the vehicle under heavy operating conditions will improve performance and extend trans- mission life by reducing excessive shifting and heat build up. This action will also provide better engine braking. The automatic transmission flu...

Page 567

Builders guide. See your authorized dealer, installer or snowplow manufacturer for this information. There are unique electrical systems that must be connected to properly assure operator safety and prevent overloading vehicle systems. Warning! Attaching a snowplow to this vehicle could adversely af...

Page 569

Operating tips under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating speed. The operator should be familiar with the area and surface to be cleaned. Reduce speed and use extreme caution when plowing unfamiliar areas or under poor visibility. Note: during snowplow usage on...

Page 571

Recreational towing – two-wheel drive models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is allowed only if the rear wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly...

Page 573

Shifting into neutral (n) – manual shift transfer case (if equipped) use the following procedure to prepare your vehicle for recreational towing. Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engagin...

Page 575

7. Shift the transmission into park. 8. Release the brake pedal. 9. Disconnect vehicle from the tow vehicle. 10. Start the engine. 11. Press and hold the brake pedal. 12. Release the parking brake. 13. Shift the transmission into gear, release the brake pedal, and check that the vehicle operates nor...

Page 577

Caution! Damage to the transmission may occur if the trans- mission is shifted into park with the transfer case in neutral and the engine running. With the transfer case in neutral, ensure that the engine is off prior to shifting the transmission into park. 15. Remove the key fob from the ignition s...

Page 579

Note: • steps 1 through 5 are requirements that must be met prior to pressing the transfer case neutral button and must continue to be met until the shift has been completed. If any of these requirements are not met prior to pressing the neutral button, or are no longer met during the shift, the neu...

Page 582

▫ center console shifter — if equipped . . . . . 609 䡵 towing a disabled vehicle . . . . . . . . . . . . . . . 610 ▫ towing without the ignition key fob . . . . . 612 ▫ two-wheel drive models . . . . . . . . . . . . . . 612 ▫ four-wheel drive vehicles . . . . . . . . . . . . . . 613 580 what to do i...

Page 584

• you can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling system could damage ...

Page 586

Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat. Jack and tools (1500 series) jack and tools (2500/3500 series) 584 what to do in emergencies.

Page 588

3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows) and tie to the jack using the tie straps. Folding flap and rolling bag tying bag to jack with straps 586 what to do in emergencies.

Page 590

Removing the spare tire remove the spare tire before attempting to jack up the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube. Rotate the wheel wrench handle cou...

Page 592

4. Place the shift lever into park. On four-wheel drive vehicles, shift the transfer case to the 4l position. 5. Turn the ignition off. 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear ...

Page 594

3. Placement of the jack: • 1500 series trucks when changing a front wheel, place the scissors jack under the rear portion of the lower control arm as shown below. Operate the jack using the jack drive tube and the wheel wrench. The tube extension may be used but is not required. 4x2 jacking locatio...

Page 596

• 2500/3500 series trucks for 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame. Operate the jack using the jack drive tube and the wheel wrench. The tube...

Page 598

Caution! Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. Note: if the bottle jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to low...

Page 600

Caution! • use a back-and-forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap finish may occur. • the rear hub caps on the dual rear wheel has two pry-off notches. Make sure that the hook of the jack handle driver is located squarely in t...

Page 602

8-stud — dual rear wheels dual wheels are flat-mounted and center-piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer. Slots in the wheels will assist in properly o...

Page 604

Warning! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immedi- ately. Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and position it proper...

Page 606

Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

Page 608

8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle. If frequent jump-starting is required to start your vehicle you should have ...

Page 610

Warning! • chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • stand clear of vehicles when pulling with tow hooks. Tow straps may become disengaged, caus- ing serious injury. Caution! Tow hooks are for emergency use only to rescue a vehicle s...

Page 612

4. Using a screwdriver or similar tool, press and hold the override tab through the access port on the center con- sole. 5. Move the shift lever into the neutral position. 6. The vehicle may then be started in neutral. 7. Reinstall the shift lever override access cover. Towing a disabled vehicle thi...

Page 614

Caution! Do not attempt to use sling type equipment when towing. When securing the vehicle to a flat bed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. Towing without the ignition key fob special care must be taken when the vehicl...

Page 617: Maintaining Your Vehicle

Maintaining your vehicle contents 䡵 engine compartment — 3.7l . . . . . . . . . . . . . 618 䡵 engine compartment — 4.7l . . . . . . . . . . . . . 619 䡵 engine compartment — 5.7l . . . . . . . . . . . . . 620 䡵 onboard diagnostic system (obd ii) . . . . . . . 621 ▫ loose fuel filler cap message . . ....

Page 619

▫ side marker lamps (dual rear wheels) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 671 䡵 fluid capacities . . . . . . . . . . . . . . . . . . . . . . 672 䡵 fluids, lubricants and genuine parts . . . . . . . 674 ▫ engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67...

Page 621

Engine compartment — 4.7l 1 — air cleaner filter 7 — washer fluid reservoir 2 — automatic transmission dipstick 8 — power steering fluid reservoir 3 — engine oil dipstick 9 — engine oil fill 4 — brake fluid reservoir 10 — coolant pressure cap 5 — battery 11 — engine coolant reservoir 6 — integrated ...

Page 623

Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

Page 625

4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

Page 627

Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

Page 629

Lubricants which do not have both the engine oil certi- fication mark and the correct sae viscosity grade num- ber should not be used. Note: for 2500/3500 trucks with a 5.7l engine oper- ating under a gross combined weight rating of 14,000 lbs (6 350 kg) or greater, sae 5w-30 engine oil is recom- me...

Page 631

Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water. R...

Page 633

Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency (epa) and is an ozone-saving product. However, the manufacturer recommends that air condi- tioning service be performed by authorized dealers ...

Page 635

Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed up, operate the defroster for a few minutes to reduce the possibility of smearing or freezi...

Page 637

Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

Page 639

Refer to the “maintenance schedule” for the proper maintenance intervals. Selection of coolant use only the manufacturer’s recommended engine cool- ant (antifreeze). Refer to “fluids, lubricants, and genu- ine parts” in “maintaining your vehicle” for further information. Caution! • mixing of engine ...

Page 641

Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To p...

Page 643

Of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the...

Page 645

With disc brakes the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted. Use only the manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “mai...

Page 647

Note: the presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage. Limited-slip differ...

Page 649

Fluid level check the fluid level should be checked when the engine is fully warmed up and the fluid in the transmission is at normal operating temperature. Operation of the trans- mission with an improper fluid level will greatly reduce the life of the transmission and of the fluid. Check the fluid...

Page 651

Trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse affect ...

Page 653

• use mopar威 touch up paint or equivalent on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap ...

Page 655

Cleaning headlights your vehicle is equipped with plastic headlights and fog lights (if equipped) that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize...

Page 657

Warning! Do not use silicon-based protection products to clean your bedliner. Silicon-based products can become slippery and may result in personal injury. Spray-on bedliners are chemically-resistant to many different types of chemicals (including gasoline, oil, hydraulic fluids) for short periods o...

Page 659

Cavity cartridge fuse mini fuse description j03 30 amp pink diesel powertrain control module – if equipped j04 25 amp natural driver door node j05 25 amp natural passenger door node j06 40 amp green antilock brakes pump/stability con- trol system j07 30 amp pink antilock brakes valve/stability con- ...

Page 661

Cavity cartridge fuse mini fuse description m13 20 amp yellow main #2 instrument cluster/wireless con- trol module/itm/ siren/multifunction switch (steering col- umn module) m14 20 amp yellow back up camera (do- mestic only) m15 20 amp yellow power seat module(s)/audio telematics/daytime running lig...

Page 663

Caution! • when installing the totally integrated power mod- ule cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the totally integrated power module and possibly result in a electrical system failure. • when replacing ...

Page 665

Bulb replacement dual or quad headlamp/front park and turn signal — if equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the four plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges. 4. Remove the two pla...

Page 667

Fog lamps 1. Reach under and behind the front bumper to access the back of the front fog lamp housing. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise 1 ⁄ 4 turn to unlock the bulb from the housing. 4. Pull the bulb straight out from th...

Page 669

Center high-mounted stoplamp (chmsl) with cargo lamp 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn the desired bulb socket 1 ⁄ 4 turn and remove the socket and bulb from housing. 7 maint...

Page 671

Cab top clearance lamps — if equipped 1. Remove the two screws from the top of the lamp. 2. Rotate the socket 1 ⁄ 4 turn and pull it from the lamp assembly. 7 maintaining your vehicle 669.

Page 673

Side marker lamps (dual rear wheels) — if equipped 1. Push rearward on the side marker lamp assembly. 2. Pull the entire assembly from the fender. 3. Turn the socket 1 ⁄ 4 turn counterclockwise and remove from assembly to access the bulb. 4. Pull the bulb straight out from socket. 5. Reverse the pro...

Page 675

U.S. Metric cooling system 3.7l engine (mopar 威 antifreeze/coolant 5 year/100,000 mile formula or equivalent) 14 quarts 13 liters 4.7l engine (mopar 威 antifreeze/coolant 5 year/100,000 mile formula or equivalent) 14 quarts 13 liters 5.7l engine — 1500 models (mopar 威 antifreeze/ coolant 5 year/100,0...

Page 677

Component fluid, lubricant, or genuine part spark plugs – 4.7l engine upper bank — fr8te2 (gap 0.039 in [.99 mm]) lower bank — fr8t1332 (gap 0.051 in [1.30 mm]) spark plugs – 5.7l engine lzfr5c–11 (gap 0.043 in [1.1 mm]) fuel selection – 3.7l and 4.7l engines 87 octane fuel selection – 5.7l engine 8...

Page 679: Maintenance Schedules

Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 678 ▫ required maintenance intervals . . . . . . . . . . 680 8 m a i n t e n a n c e s c h e d u l e s.

Page 681

Note: • the oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is not illuminated. • change your engine oil more often if you drive your vehicle off...

Page 683

8,000 miles (13,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only). Odomet...

Page 685

40,000 miles (65,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only). Odo...

Page 687

64,000 miles (104,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). ❏ replace the engine air cleaner filter. ❏ replace the ignition cable...

Page 689

88,000 miles (143,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only). O...

Page 691

104,000 miles (169,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only)....

Page 693

128,000 miles (208,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). ❏ replace the engine air cleaner filter. ❏ replace the ignition cab...

Page 695

Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • failure to properly inspect and mai...

Page 698

䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 703 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 703 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 703 ▫ temperature grades . . . . . . . . . . . . . . . . . . 70...

Page 700