1. DL manuals
  2. RAM
  3. Automobile
  4. 2013 Cargo Van
  5. Owner's Manual

RAM 2013 Cargo Van Owner's Manual

Other manuals for 2013 Cargo Van: Owner's Manual

Summary of 2013 Cargo Van

  • Page 1

    1207472cv1 13mzz-126-ab chrysler 1" gutter 06/13/2012 17:12:08 r a m c v c a r g o v a n chrysler group llc o w n e r ’ s m a n u a l 2 0 1 3 2 0 13 ram c argo v an 13mzz-126-ab second edition printed in u.S.A. R a m c v c a r g o v a n chrysler group llc o w n e r ’ s m a n u a l 2 0 1 3 2 0 13 ram...

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of acci- dents. Your driving ability...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .4 䡵 warnings and cautions . . . . . . . . . . . . . .6 䡵 van conversions/campers . . . . . . . . . . . .6 䡵 vehicle identification number . . . . . . . .7 䡵 vehic...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 9

    Operating instructions for the special equipment in- stalled by the conversion/camper manufacturer should also be supplied with your vehicle. If these instructions are missing, please contact your authorized dealer for assistance in obtaining replacement documents from the applicable manufacturer. F...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Vehicle identification number 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ wireless ignition node (win) . . . . . . . . . . . . .12 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ removing key fob from ignition . . . . . . . . . .14 ▫ key-in-i...

  • Page 12

    䡵 remote keyless entry (rke) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .21 ▫ using the rke transmitter . . . . . . . . . . . . . . .21 䡵 remote starting system — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .30 ▫ how to use remote start . . . . . . . . . . . . ...

  • Page 13

    ▫ supplemental active head restraints (ahr) . . .68 ▫ enhanced seat belt use reminder system (beltalert®) . . . . . . . . . . . . . . . . . . . . . . . . . .73 ▫ seat belts and pregnant women . . . . . . . . . . .74 ▫ seat belt extender . . . . . . . . . . . . . . . . . . . . .74 ▫ supplemental rest...

  • Page 14

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a wireless ignition node (win) with integral ignition switch. You can insert the key fob into the ignition switch with either side up. Wireless igniti...

  • Page 15

    Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key ...

  • Page 16

    Removing key fob from ignition place the shift lever in park. Turn the key fob to the off position and then remove the key fob. Note: power window switches will also remain active for up to 10 minutes after the ignition switch has been turned to off, depending upon the accessory delay setting. Openi...

  • Page 17

    Caution! An unlocked car is an invitation to thieves. Always remove the key fob from the ignition and lock all doors when leaving the vehicle unattended. Key-in-ignition reminder opening the driver’s door when the key fob is in the ignition and the ignition switch position is off or acc, a chime wil...

  • Page 18

    The bulb check, it indicates that someone used an invalid key fob to start the engine. Either of these conditions will result in the engine being shut off after two seconds. If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indica...

  • Page 19

    Note: when having the sentry key® immobilizer sys- tem serviced, bring all vehicle key fobs with you to the authorized dealer. Customer key programming programming key fobs or rke transmitters may be performed at an authorized dealer. General information the sentry key® system complies with fcc rule...

  • Page 20

    Rearming of the system the vehicle security alarm will rearm itself after the 15 additional minutes of headlights and vehicle security light flashing, if the vehicle security alarm has not been disabled. If the condition which initiated the alarm is still present, the vehicle security alarm will ign...

  • Page 21

    Note: • the driver’s door key cylinder and the liftgate button on the rke transmitter cannot arm or disarm the vehicle security alarm. • the vehicle security alarm remains armed during power liftgate entry. Pressing the liftgate button will not disarm the vehicle security alarm. If someone enters th...

  • Page 22

    Security system manual override the vehicle security alarm will not arm if you lock the doors using the manual door lock plunger. Illuminated entry — if equipped the courtesy lights will turn on when you use the remote keyless entry (rke) transmitter to unlock the doors or open any door. This featur...

  • Page 23

    Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors and liftgate, and activate the panic alarm, optional power liftgate, left power sliding door, and right power sliding door from distances up to approximately 66 ft (20 m) using a hand-held key fob with rke tr...

  • Page 24

    Seven-button rke transmitters will provide functions that allow the same basic operation as the three-button, but may also be used to operate the power liftgate (optional), power sliding doors, remote start feature (optional). Some fea- tures can be programmed to the customers preferences. For examp...

  • Page 25

    Remote key unlock on first press this feature lets you program the system to unlock either the driver’s side, or all doors, on the first press of the unlock button on the rke transmitter: note: • for vehicles equipped with an electronic vehicle in- formation center (evic), refer to “electronic vehic...

  • Page 26

    Remote lock doors and liftgate press and release the lock button on the rke transmit- ter to lock all doors and liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Sound horn with remote lock this feature will cause the horn to chirp when the doors are lock...

  • Page 27

    Note: pressing the lock button on the rke transmit- ter while you are in the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Press the unlock button to deactivate the vehicle security alarm. Using the panic ala...

  • Page 28

    If equipped with a rear interior switch on the left rear pillar, pushing this switch once will close the liftgate only. The liftgate cannot be opened from this switch. If the vehicle is locked and vehicle security alarm is armed, using rke transmitter to open the power liftgate does not unlock the v...

  • Page 29

    Turn off flash lights with rke lock — if equipped this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the...

  • Page 30

    Programming additional transmitters if you do not have a programmed rke transmitter, contact your authorized dealer for details. Transmitter battery replacement the recommended replacement battery is one cr2032 battery. Note: • perchlorate material — special handling may apply. See www.Dtsc.Ca.Gov/h...

  • Page 31

    3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it wit...

  • Page 32

    4. To assemble the rke transmitter case, snap the two halves together. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept ...

  • Page 33

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • liftgate closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switch • battery at...

  • Page 34

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 35

    • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the remote start mode. • the engine can be started two consecutive 15-minute cycles with the rke transmitter. However, the ignition switch must be turned to the on/run position. To enter the ...

  • Page 36

    Cancel remote start remote starting will also cancel if any of the following occur: • the engine stalls or engine speed exceeds 2500 rpm • any engine warning lights come on • low fuel light turns on • the hood is opened • the hazard switch is pressed • the shift lever is moved out of park • the engi...

  • Page 37

    Door locks manual door locks lock the front doors by pushing down on the lock knobs on each door trim panel. If the lock knob is down when you shut either front door, the door will lock. Make sure the keys are not inside the vehicle before closing the door. If the lock knob is rearward when you shut...

  • Page 38

    Warning! • for personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. (continued) warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in ...

  • Page 39

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave a vehicle equipped with keyless enter-n- go™ in the acc or on/run position. A child could operate power windows, other controls, or move the vehicle. Power door locks — i...

  • Page 40

    Operate. A chime will sound if the key fob is in the ignition switch and a door is open, as a reminder to remove the key fob. If you press the power door lock switch while the sliding door is open, the sliding door will lock. Automatic door locks — if equipped when enabled, the door locks will lock ...

  • Page 41

    The unlock doors automatically on exit feature will not operate if there is any manual operation of the power door locks (lock or unlock). On vehicles equipped with the optional electronic ve- hicle information center (evic), refer to “electronic vehicle information center (evic)/personal settings (...

  • Page 42

    Note: power window switches will also remain active for up to 10 minutes after the ignition switch has been turned to off, depending upon the accessory delay setting. Opening a front door will cancel this feature. Power window lockout switch — if equipped the driver may lock out the rear power windo...

  • Page 43

    Front passenger power window switch there is a single switch on the front passenger’s door trim panel which operates the passenger door window and a set of switches that lock and unlock all doors. The switches will operate only when the ignition switch is in the on/run or acc position and during pow...

  • Page 44

    Auto-down feature — if equipped the front window switches may be equipped with an auto-down feature. Press the window switch past the detent, release, and the window will go down automati- cally. To open the window part way, press the window switch part way and release it when you want the window to...

  • Page 45

    Note: • if the window runs into any obstacle during auto- closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. • any impact due to rough road conditions may trigger the auto reverse function unexpectedly during auto- closu...

  • Page 46

    The switches will operate only when the ignition switch is in the on/run or acc position and during power accessory delay. Note: the switches will not operate if the driver has activated the power window lockout. Note: the sliding door windows do not fully open, stopping several inches above the win...

  • Page 47

    Rocking forward and back. Rocking the handle back- wards opens the door and rocking forward releases the hold open latch in order to close the door. To keep your door operating properly, observe the fol- lowing guidelines: • always open the door smoothly. • avoid high impacts against the door stop w...

  • Page 48

    Note: pulling the outside power sliding door handle a second time while the sliding door is power opening or power closing will allow the sliding door to be opened or closed manually. Press the button on the rke transmitter twice within 5 seconds to open a power sliding door. When the door is fully ...

  • Page 49

    Master lock button, located in the overhead console, to disable the switches and handles for the rear seat passengers. Note: • the power sliding side door switches will not open the power sliding door if the shift lever is in gear or the vehicle speed is above 0 mph (0 km/h). To close the power slid...

  • Page 50

    Power sliding side door open flash the left and right exterior hazard lights will flash for 12 seconds when either sliding door is opened. This will alert other drivers in the area that passenger(s) could be entering or exiting the vehicle. The sliding side door open flash can be enabled or disabled...

  • Page 51

    Sliding side door child protection lock to provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a child protection door lock system. Note: when the child protection door lock system is engaged, the door can be opened only by using the outside d...

  • Page 52

    3. Repeat steps 1 and 2 on the opposite sliding door. Note: • after engaging the child protection door lock, always test the door from the inside to make certain it is in the desired position. • when the child protection door lock system is en- gaged, (even if the inside door lock is in the unlocked...

  • Page 53

    Warning! Avoid trapping anyone in the vehicle in a collision. Remember that the sliding doors can only be opened from the outside door handle or the switches located on the trim panel just in front of the power sliding door when the child protection door locks are engaged. To disengage the child pro...

  • Page 54

    Liftgate on vehicles equipped with power locks, the liftgate can be unlocked using the remote keyless entry (rke) transmitter button, or by activating the power door lock switches located on the front doors. To open the liftgate, press the liftgate release handle located on the underside of the lice...

  • Page 55

    Power liftgate — if equipped the power liftgate may be opened manually or by using the button on the remote keyless entry (rke) transmit- ter. Press the button on the transmitter twice within five seconds, to open the power liftgate. When the liftgate is fully open, pressing the button twice within ...

  • Page 56

    The power liftgate may be closed by pressing the button, located in the upper left trim in the liftgate opening. Pushing once will only close the liftgate. This button cannot be used to open the liftgate. When the rke transmitter button is pressed and the flash lights feature is enabled, the tail li...

  • Page 57

    • during power operation, whether liftgate is fully open or fully closed, the liftgate chime will beep several times indicating power operation is in progress. • the power liftgate must be in the full open or close positions for any of the buttons to operate. If the liftgate is not in the full open ...

  • Page 58

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for all seating positions • advanced front air bags for driver and front passen- ger • supplemental active head restraints (ahr) located on top of the front ...

  • Page 59

    If you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for children (latch) feature also can be used to hold infant and child restraint systems. For more information on latch, refer to lower anchors and tether for children (latch). Note:...

  • Page 60

    If a child from 1 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (refer to “child restraints”) you should read the instructions provided with your child restraint to make sure that you...

  • Page 61

    Warning! (continued) • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • supplemen...

  • Page 62

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 63

    Warning! (continued) • wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • two pe...

  • Page 64

    Warning! • a belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause inter- nal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so...

  • Page 65

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden st...

  • Page 66

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt may not protect you properly. In a collisi...

  • Page 67

    Pull the strap down and secure the small latch plate of the lap belt into the small buckle until you hear a “click”. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. When the belt is long enough to fit , insert the large latch plate into the buckle unt...

  • Page 68

    You will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Seat belts in passenger seating positions the seat belts in the passenger seating positions are equipped with an automatic locking retractor (alr) or a cinching la...

  • Page 69

    Position that has a belt with this feature. Children 12 years old and under should always be properly re- strained in the rear seat. How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extr...

  • Page 70

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 71

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 72

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: for more information on properly adjusting and positi...

  • Page 73

    2. Position the hands on the top of the deployed ahr at a comfortable position. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand positioning points on ahr 1 — downward movement 2 — rearward movement 2 things to know before starting your vehic...

  • Page 74

    4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an autho...

  • Page 75

    Enhanced seat belt use reminder system (beltalert®) beltalert® is a feature intended to remind the driver and front passenger (if equipped with front passenger beltalert®) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted...

  • Page 76

    Beltalert® can be enabled or disabled by your autho- rized dealer. Chrysler group llc does not recommend deactivating beltalert®. Note: although beltalert® has been deactivated, the seat belt reminder light will continue to illuminate while the driver’s or front passenger (if equipped with beltalert...

  • Page 77

    Supplemental restraint system (srs) — air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s advanced front air bag is mounted in the center of the steering wheel. The passenger’s advanced front air b...

  • Page 78

    Note: the driver and front passenger advanced front air bags are certified to the new federal regulations for advanced air bags. The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severit...

  • Page 79

    Air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • supplemental driver side knee air bag • knee impact bolster • driver advanced front air ...

  • Page 80

    Warning! • no objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • do not put anything on or around the air bag covers or attempt to open them manually. Y...

  • Page 81

    When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental side air bag inflatable curtain (sabic) — if equi...

  • Page 82

    Warning! • your vehicle is equipped with left and right supplemental side air bag inflatable curtain (sabic), do not stack luggage or other cargo up high enough to block the location of the sabic. The area where the sabic is located should remain free from any obstructions. • do not use accessory se...

  • Page 83

    Always sit upright as possible with your back against the seat back, use the seat belts properly, and use the appropriate sized child restraint, infant restraint or booster seat recommended for the size and weight of the child. Supplemental driver side knee air bag the supplemental driver side knee ...

  • Page 84

    Collisions depending on several factors, including the severity and type of collision. Advanced front air bags are not expected to reduce the risk of injury in rear, side, or rollover collisions. The advanced front air bags and supplemental driver side knee air bag will not deploy in all frontal col...

  • Page 85

    The orc contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. Also, the orc turns on the air bag warning light in the instrument panel for approxi- mately four to eight seconds for a self-check when the igni...

  • Page 86

    Driver and passenger advanced front air bag inflator units the driver and passenger advanced front air bag inflator units are located in the center of the steering wheel and on the right side of the instrument panel. When the orc detects a collision requiring the ad- vanced front air bags, it signal...

  • Page 87

    Supplemental seat-mounted side air bag (sab) inflator units the supplemental seat-mounted side air bags (sab) are designed to activate only in certain side collisions. The orc determines if a side collision requires the side air bags to inflate, based on the severity and type of collision. Based on ...

  • Page 88

    Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an air bag should have deployed. Note: in a rollover the pretensioners and/or sab and sabic air bags may deploy on both sides of the vehicle. Front and side impact sensors in f...

  • Page 89

    If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or al...

  • Page 90

    Warning! Deployed air bags and seat belt pretensioners can not protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retrac- tor assemblies replaced by an authorized dealer im- mediately. Also, have the occupant restraint con- troller (orc) system serv...

  • Page 91

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion,...

  • Page 92

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of t...

  • Page 93

    These data can help provide a better understanding of the circumstances in which crashes and injuries occur. Note: edr data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the edr under normal driving conditions and no per- sonal data (e.G., name, g...

  • Page 94

    Before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. You should also make sure that you can install it in the vehicle where you will use it. Note: for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. Ca...

  • Page 95

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 96

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 97

    Have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above t...

  • Page 98

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 99

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 100

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 101

    Latch positions for installing child restraints in this vehicle second row captains chairs lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol second row bench lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol 2 things to know befor...

  • Page 102

    Child restraint latch positions what is the weight limit (child’s weight + weight of the child re- straint) for using the latch an- chorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (...

  • Page 103

    Can two child restraints be at- tached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchor- ages, use the seat belt to install a child seat in the center position next to a child...

  • Page 104

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between ...

  • Page 105

    Locating the latch anchorages in addition, there are tether strap anchors lo- cated behind each rear seatback, near to the floor. Latch anchorages (third row 60/40 anchorages shown) latch anchorages (third row 60/40 anchorage shown) 2 things to know before starting your vehicle 103.

  • Page 106

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing infant restraint...

  • Page 107

    Center seat latch if a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard latch anchors or seat belt, do not install a child seat in that outb...

  • Page 108

    4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 109

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using...

  • Page 110

    Lap/shoulder belt systems for installing child restraints in this vehicle second row captains chair second row bench 108 things to know before starting your vehicle.

  • Page 111

    Lap/shoulder belt systems what is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forwar...

  • Page 112

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. 2. Pull enough of the seat belt webbing fro...

  • Page 113

    8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “lower anchors and tethers for chil- dren (latch) restraint system” for directions to attach a tether anchor. 9. Test...

  • Page 114

    4. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat. 5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether str...

  • Page 115

    Installing child restraints using the top tether anchorage 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for t...

  • Page 116

    4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child res...

  • Page 117

    Commercial cargo vehicles (no factory installed rear seats) — if equipped commercial cargo vehicles are not designed for use as a family vehicle and are not intended for carrying children in the front passenger seat. However, if you must carry a child in a vehicle without a rear seat, the passenger ...

  • Page 118

    Restraining infants and small children in commercial cargo vehicles there are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child. Refer to “child restraints” in the “occupa...

  • Page 119

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 120

    Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 121

    The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, hav...

  • Page 122

    Air bag warning light the light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned on. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked...

  • Page 123

    Warning! (continued) • never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfer- ing with the pedals or the ability to control the vehicle. • never put floor mats or other floor coverings on top of already inst...

  • Page 124

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 125: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 ▫ inside day/night mirror — if equipped . . . .130 ▫ automatic dimming mirror — if equipped . . .131 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . .132 ▫ driver’s ou...

  • Page 126

    ▫ phone call features . . . . . . . . . . . . . . . . . . . .155 ▫ uconnect® phone features . . . . . . . . . . . . . . .158 ▫ advanced phone connectivity . . . . . . . . . . . .163 ▫ things you should know about your uconnect® phone . . . . . . . . . . . . . . . . . . . . .165 ▫ general information...

  • Page 127

    䡵 driver memory seat — if equipped . . . .214 ▫ setting memory positions and linking rke transmitter to memory . . . . . . . . . . . . .215 ▫ easy entry/exit seat (available with memory seat only) . . . . . . . . . . . . . . . . . . .218 䡵 to open and close the hood . . . . . . . . .219 䡵 lights . ....

  • Page 128

    䡵 tilt/telescoping steering column . . .232 䡵 heated steering wheel — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .233 䡵 adjustable pedals — if equipped . . . . . .234 䡵 electronic speed control — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .236 ▫ to activate . . . . ...

  • Page 129

    ▫ turning parkview® on or off — without navigation/multimedia radio . . . . . . . . . . . .251 䡵 overhead consoles . . . . . . . . . . . . . . . . .251 ▫ front overhead console. . . . . . . . . . . . . . . . .251 ▫ courtesy/interior lighting . . . . . . . . . . . . . .252 ▫ sunglass storage (non-sun...

  • Page 130

    ▫ venting sunroof — express . . . . . . . . . . . . . .268 ▫ sunshade operation. . . . . . . . . . . . . . . . . . . .268 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . .268 ▫ sunroof maintenance . . . . . . . . . . . . . . . . . . .268 ▫ ignition off operation . . . . . . . . . . . . ...

  • Page 131

    䡵 console features . . . . . . . . . . . . . . . . . . .286 ▫ basic console . . . . . . . . . . . . . . . . . . . . . . . .287 ▫ premium console — if equipped . . . . . . . . . .288 ▫ super console — if equipped. . . . . . . . . . . . .292 䡵 ram cargo van features . . . . . . . . . . . .294 ▫ ram ca...

  • Page 132

    Mirrors inside day/night mirror — if equipped a two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (towa...

  • Page 133

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 134

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really...

  • Page 135

    Power mirrors — if equipped the power mirror controls are located on the driver-side door trim panel. The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a mirror, press either the l (left) or r (right) to select the mirror that you want to ad...

  • Page 136

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Some vehicles may not be equipped with rear window defroster, in this case the heated mirrors will still function as intended. Refer...

  • Page 137

    Note: if the vehicle speed is greater than 10 mph (16 km/h) the folding feature will be disabled. If the mirrors are in the folded position, and vehicle speed is equal or greater than 10 mph (16 km/h), they will automatically unfold. Resetting the power folding outside mirrors you may need to reset ...

  • Page 138

    Blind spot monitoring (bsm) — if equipped the blind spot monitoring (bsm) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicl...

  • Page 139

    When the vehicle is started, the bsm warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational. Automatic transmission vehicles the bsm system sensors operate when the vehicle is in any forward gear or reverse and enters stand-b...

  • Page 140

    Note: • the bsm system does not alert the driver about rapidly approaching vehicles that are outside the de- tection zones. • the bsm system detection zone does not change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer bef...

  • Page 141

    The bsm system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary. The bsm system will issue an alert during these types of zone entries. Entering from the side vehicles that move into your adjacent lanes from either side o...

  • Page 142

    Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Overtaking traffic if you pass another vehicle slowly (with a relative speed of less than 15 mph (24 km/h) and the vehicle remai...

  • Page 143

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects t...

  • Page 144

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm (continued) warning! (continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicle’s ...

  • Page 145

    Rcp monitors the rear detection zones on both sides of the vehicle, for objects that are moving toward the side of the vehicle with a minimum speed of approximately 3 mph (5 km/h), to objects moving a maximum of approximately 20 mph (32 km/h), such as in parking lot situations. Note: in a parking lo...

  • Page 146

    Modes of operation modes of operation with evic three selectable modes of operation are available in the electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)/personal settings (customer-programmable features)” in “under- standing your instrument panel”...

  • Page 147

    Note: • whenever an audible alert is requested by the bsm system, the radio is also muted. • if the hazard flashers are on, the system will request the appropriate visual alert only. When the system is in rcp, the system shall respond with both visual and audible alerts when a detected object is pre...

  • Page 148

    For uconnect® customer support: • u.S. Residents - visit www.Uconnectphone.Com or call 1–877–855–8400. • canadian residents - visit www.Uconnectphone.Com or call, 1-800-465–2001 (english) or 1-800-387-9983 (french). Uconnect® phone allows you to transfer calls between the system and your mobile phon...

  • Page 149

    Uconnect® phone button the radio or steering wheel controls (if equipped) will contain the two control buttons (uconnect® phone button and voice com- mand button) that will enable you to access the system. When you press the button you will hear the word uconnect® followed by a beep. The beep is you...

  • Page 150

    • for certain operations, compound commands can be used. For example, instead of saying “setup” and then “pair a device”, the following compound command can be said: “pair a bluetooth® device”. • for each feature explanation in this section, only the compound form of the voice command is given. You ...

  • Page 151

    To complete the pairing process, you will need to refer- ence your mobile phone owner’s manual. The uconnect® website may also provide detailed instruc- tions for pairing. The following are general phone to uconnect® phone pairing instructions: • press the button to begin. • after the “ready” prompt...

  • Page 152

    Dial by saying a number • press the button to begin. • after the “ready” prompt and the following beep, say “dial”. • the system will prompt you to say the number you want to call. • for example, you can say “151-1234 -5555”. • the uconnect® phone will confirm the phone number and then dial. The num...

  • Page 153

    • when prompted, say the name of the new entry. Use of long names helps the voice command and it is recom- mended. For example, say “robert smith” or “robert” instead of “bob”. • when prompted, enter the number designation (e.G., “home”, “work”, “mobile”, or “other”). This will allow you to store mu...

  • Page 154

    • a maximum of 1000 entries per phone will be down- loaded and updated every time a phone is connected to the uconnect® phone. • depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previou...

  • Page 155

    After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. “phonebook edit” can be used to add another phone number to a name entry that already exists in the phonebo...

  • Page 156

    Delete/erase “all” uconnect® phonebook entries • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook erase all”. • the uconnect® phone will ask you to verify that you wish to delete all the entries from the phonebook. • after confirmation, the phonebook entri...

  • Page 157

    Phone call features the following features can be accessed through the uconnect® phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the uconnect® phone. Check with your mobile se...

  • Page 158

    In progress. To go back to the first call, refer to “toggling between calls” in this section. To combine two calls, refer to “conference call” in this section. Place/retrieve a call from hold to put a call on hold, press the button until you hear a single beep. This indicates that the call is on hol...

  • Page 159

    Active call is terminated by the phone far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the button until you hear a single beep. Redial • press the button to begin. • after the “ready” prompt and the following...

  • Page 160

    Uconnect® phone features language selection to change the language that the uconnect® phone is using: • press the button to begin. • after the “ready” prompt and the following beep, say the name of the language you wish to switch to english, espanol, or francais. • continue to follow the system prom...

  • Page 161

    Note: • the emergency number dialed is based on the country where the vehicle is purchased (911 for the u.S. And canada and 060 for mexico). The number dialed may not be applicable with the available mobile service and area. • if supported, this number may be programmable on some systems. To do this...

  • Page 162

    Note: you should program the desired towing assis- tance phone number using the voice command system. To do this, press the button and say “setup”, followed by “towing assistance”. When prompted say 1-800-528- 2069 for the u.S., say 1-800-363-4869 for canada, say 55-14- 3454 for mexico city and 1-80...

  • Page 163

    “send”, is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored uconnect® phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wi...

  • Page 164

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G., the uconnect® phone will not repeat a phone number before you dial it). • press the button to begin. • after the “ready” prompt and the following beep, say one of the followi...

  • Page 165

    Mute/un-mute (mute on/off) when you mute the uconnect® phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect® phone: • press the button. • following the beep, say “mute”. In order to un-mute...

  • Page 166

    • when prompted, say “list phones”. • the uconnect® phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “se- lect” or “delete”. Also, see the next two sections f...

  • Page 167

    Things you should know about your uconnect® phone uconnect® phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect® tutorial.” voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect® pho...

  • Page 168

    This will delete all phone pairing, phone book entries, and other settings in all language modes. The system will prompt you before resetting to factory settings. Voice command • for best performance, adjust the rearview mirror to provide at least ½ in (1 cm) gap between the overhead console (if equ...

  • Page 169

    • it is not recommended to store similar sounding names in the uconnect® phonebook. • phonebook (downloaded and uconnect® phone lo- cal) name recognition rate is optimized when the entries are not similar. • numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight h...

  • Page 170

    Recent calls if your phone supports “automatic phonebook down- load”, uconnect® phone can list your outgoing, incom- ing and missed calls. Voice text reply uconnect® phone can read or send new messages on your phone. Read messages: if you receive a new text message while your phone is connected to u...

  • Page 171

    Uconnect® phone will prompt you to say the name or number of the person you wish to send the message to. List of preset messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L o l 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See you in 15 minutes 12. I am on my way...

  • Page 172

    Turn voice text reply incoming announcement on/ off turning the voice text reply incoming announcement off will stop the system from announcing the new incoming messages. • press the button. • after the “ready” prompt and the following beep, say “setup, incoming message announcement”, you will then ...

  • Page 173

    3 understanding the features of your vehicle 171.

  • Page 174

    172 understanding the features of your vehicle.

  • Page 175

    3 understanding the features of your vehicle 173.

  • Page 176

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location voice commands primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais 174 understanding ...

  • Page 177

    Voice commands primary alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book voice commands primary alternate (s) previous record again redial return to main menu return or main menu select phone select...

  • Page 178

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 179

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When you press the voice command button, you...

  • Page 180

    To hear the first available menu, press the voice com- mand button and say “help” or “main menu”. Commands the voice command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the volum...

  • Page 181

    Radio am to switch to the am band, say “am” or “radio am”. In this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “m...

  • Page 182

    Disc mode to switch to the disc mode, say “disc”. In this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) usb mode to switch to usb mode, s...

  • Page 183

    • “play memos” (to play previously recorded memos) — during the playback you may press the voice com- mand button to stop playing memos. You pro- ceed by saying one of the following commands: – “repeat” (to repeat a memo) – “next” (to play the next memo) – “previous” (to play the previous memo) – “d...

  • Page 184

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect® voice “voice training” feature may be used. 1. Press the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your...

  • Page 185

    Power seats — if equipped some models may be equipped with eight-way power seats for the driver and front passenger. The power seat switches are located on the outboard side of the seat. The switches control the movement of the seat cushion and the seatback. Driver power seat switch 1 — seat switch ...

  • Page 186

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 187

    Tilting the seat up or down the angle of the seat cushion can be adjusted in four directions. Pull upward or push downward on the front or rear of the seat switch, the front or rear of the seat cushion will move in the direction of the switch. Release the switch when the desired position has been re...

  • Page 188

    Caution! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power lumbar — if equipped vehicles equipped with power driver or passenger seat...

  • Page 189

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters located in the seat cushions. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or o...

  • Page 190

    You can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high-level heating. Press the switch a second time to select low-l...

  • Page 191

    You can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high-level heating. Press the switch a second time to select low-l...

  • Page 192

    When the high-level setting is selected, the heater will provide a boosted heat level during the initial stages of operation. Then, the heat output will drop to the normal high-level. If the high-level setting is selected, the system will automatically switch to low-level after approximately 60 minu...

  • Page 193

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 194

    Normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched. Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result i...

  • Page 195

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 196

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. Active head restraint (normal position) active head restraint (tilted) 194 understanding the features of your vehi...

  • Page 197

    • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head restraints (ahr)” in “things to know before starting your vehicle” for further information. Warning! • do not place items over the top of the active head restraint, such as coats, seat cov...

  • Page 198

    Head restraints — second row bench to raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. Head restraints — third row the head restraint in the center posi...

  • Page 199

    Note: seat will not stow in the storage bin unless the armrests are raised. 4. Slide the storage bin locking mechanism to the “lock” position and then pull up on the storage bin latch to open the cover. 5. Pull upward on the seatback recliner lever located on the outboard side of the seat. The non-a...

  • Page 200

    The seat will automatically tumble into position for easy storage. Non-adjustable head restraint automatic folding seatback 198 understanding the features of your vehicle.

  • Page 201

    6. Push the seat into the storage bin. 7. Close the storage bin cover. Caution! The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. Tumbled second row seat seat in storage bin 3 understanding the features o...

  • Page 202

    Warning! In a collision, serious injury could result if the seat storage bin covers are not properly latched. • do not drive the vehicle with the storage bin covers open. • keep the storage bin covers closed and latched while the vehicle is in motion. • do not use a storage bin latch as a tie down. ...

  • Page 203

    2. Return the head restraint to the upright position. 3. Pull up on the seatback recliner lever on the outboard side of the seat to fold head rest and seatback and tumble seat forward. Raising the seatback raising the head restraint 3 understanding the features of your vehicle 201.

  • Page 204

    Easy entry second row the second row stow ’n go® seats allow easy entry to the third row seat or rear cargo area. Pull up on the seatback recliner lever on the outboard side of the seat. The seat will automatically fold into position for easy entry into the third row. Warning! In the event of a coll...

  • Page 205

    While sitting in the seat, pull up on the handle and slide the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! • adjusting a seat while dri...

  • Page 206

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Fold-flat to fold the seat, lift the recliner lever to the full upward position and pu...

  • Page 207

    Easy entry the quad seats can be tilted forward for easy entry into the third row. With the quad seat in the fold-flat position, lift up on the easy entry lever located near the bottom of the seat and lift the seat forward. For passengers seated in the third row, there is a pull strap located on the...

  • Page 208

    Removal the quad seats can be removed if additional storage is needed. With the seat in the easy entry position, lift the cross beam forward and up to release the front anchor latches. Second row bench seat — if equipped while the bench seat does not stow in the floor, it is removable for added carg...

  • Page 209

    Indicator button pops up when the seat is unlocked. The seat assembly can now be removed from the vehicle and moved on its easy out® rollers. To reinstall the seat, align the seat into the detent posi- tions on the floor. Squeeze the release handle and rotate upward until the lock indicator button r...

  • Page 210

    Third row power folding seat — if equipped a one-touch power folding seat switch is located in the left rear trim panel as part of a switch bank. Note: lower the head restraint by pulling on the release strap marked “1” located on the outboard side of the head restraint. The switch is only functiona...

  • Page 211

    The rear switch bank allows multiple power folding and unfolding positions for the third row seats. Left and right third row seats can be folded individually or together. The third row power folding seat adjusts to the following positions using the switch bank located on the left rear trim panel: on...

  • Page 212

    Note: • disconnect the center shoulder belt from the small buckle and lower the head restraints before attempting to fold/stow the power third row seats. • to abort seat operation while seat is in motion, press a different seat position selector switch to stop the seat. Once the seat stops moving, t...

  • Page 213

    3. Pull release strap marked “2” located on the rear of the seat to lower the seatback. 4. Pull release strap marked “3” to release the anchors. Head restraint release strap “1” release strap “2” 3 understanding the features of your vehicle 211.

  • Page 214

    5. Pull release strap marked “4” and tumble the seat rearward into the storage bin. Release strap “3” release strap “4” 212 understanding the features of your vehicle.

  • Page 215

    To unfold third row seats 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. 2. Pull release strap marked “2” to unlock the recliner. 3. Pulling strap “4” releases the seatback to return to its full upright position. 4. Raise the...

  • Page 216

    Tailgate mode 1. Pull release strap “3”, then pull release strap “4” to rotate the entire seat rearward. 2. To restore the seat to its upright position, lift up on the seatback and push forward until the anchors latch. Warning! To avoid serious injury or death, never operate the vehicle with occupan...

  • Page 217

    Your vehicle may have been delivered with two rke transmitters. Only one rke transmitter can be linked to each of the memory positions. Setting memory positions and linking rke transmitter to memory note: each time the set (s) button and a numbered button (1 or 2) is pressed, you erase the memory se...

  • Page 218

    5. Turn on the radio and set the radio station presets (up to 10 am and 10 fm stations can be set). 6. Turn the ignition switch to the off position and remove the key. 7. Press and release the set (s) button located on the driver’s door. 8. Within five seconds, press and release memory button 1 or 2...

  • Page 219

    To recall the memory setting for driver two, press memory button 2 on the driver’s door or the unlock button on the rke transmitter linked to memory position 2. A recall can be cancelled by pressing any of the memory buttons on the driver’s door during a recall (s, 1, or 2). When a recall is cancell...

  • Page 220

    Note: once programmed, all rke transmitters linked to memory can be easily enabled or disabled at one time. Refer to “electronic vehicle information center (evic)/ customer-programmable features ⬙ in “understanding your instrument panel” for further information. Easy entry/exit seat (available with ...

  • Page 221

    Note: the easy entry/easy exit feature can be enabled or disabled through the programmable features in the electronic vehicle information center (evic). If your vehicle is not equipped with an evic, your dealership can activate/deactivate this feature for you. For details, refer to “electronic vehic...

  • Page 222

    Use the hood prop rod to secure the hood in the open position. Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 12 in (30 cm) and then drop it. This should (continued) safety lever location hood prop rod 220 understanding the feat...

  • Page 223

    Caution! (continued) secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. ...

  • Page 224

    Automatic headlights — if equipped this system automatically turns your headlights on or off based on ambient light levels. To turn the system on, turn the headlight switch to the extreme counterclockwise position aligning the indicator with the auto on the headlight switch. When the system is on, t...

  • Page 225

    The headlight delay time is programmable on vehicles equipped with an evic. Refer to “electronic vehicle information center (evic)/customer-programmable features” in “understanding your instrument panel” for further information. If the headlights are turned off before the ignition, they will turn of...

  • Page 226

    Dimmer controls the dimmer switch is located next to the headlight switch. With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights. Interior lighting on rotate the left dimmer control completely upward to the second det...

  • Page 227

    Note: the key must be out of the ignition switch or the ignition switch must be in the off position for this feature to operate. Interior lighting off rotate the left dimmer control to the off position (extreme bottom). The interior lights will remain off when the doors or liftgate are open. Parade ...

  • Page 228

    Multifunction lever the multifunction lever is located on the left side of the steering column. The multifunction lever controls the: • turn signals • headlight beams low/high • flash-to-pass (optical horn) • front and rear wipers — washer functions turn signals move the multifunction lever up or do...

  • Page 229

    Turn signal warning if the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about 1 mile (1.6 km) with the turn signals on, a chime will sound to alert the driver. Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn sig...

  • Page 230

    Windshield wiper and washers the wipers and washers are operated by a switch within the multifunction lever. Rotate the end of the multifunc- tion lever to select the desired wiper speed. Note: always remove any buildup of snow that pre- vents the windshield wiper blades from returning to the off po...

  • Page 231

    Intermittent wiper system use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause be- tween cycles desirable. Rotate the end of the multifunc- tion lever to the first detent position, and then turn the end of the lever to select the desired delay interval....

  • Page 232

    Rear wiper and washer rotating the rotary ring to the first detent activates the rear intermittent wipers. To activate the washers, rotate the rotary ring fully forward and the washers will spray until the ring is released, and then resume the intermit- tent interval. Note: rear window wipers functi...

  • Page 233

    • the rain sensing feature can be turned on and off through the evic (if equipped). Refer to “electronic vehicle information center (evic)/personal settings (customer-programmable features)” in “understand- ing your instrument panel” for further information. The rain sensing system has protective fe...

  • Page 234

    Tilt/telescoping steering column this feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column. To unlock the steering column, pus...

  • Page 235

    Heated steering wheel — if equipped the steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate for approximately 30 to 80 minutes before automa...

  • Page 236

    Vehicles equipped with remote start on models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further information. Warning! • person...

  • Page 237

    Press the switch forward to move the pedals forward (toward the front of the vehicle). Press the switch rearward to move the pedals rearward (toward the driver). • the pedals can be adjusted with the ignition off. • the pedals cannot be adjusted when the vehicle is in reverse or when the electronic ...

  • Page 238

    Caution! Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path. Warning! Do not adjust the pedals while the vehicle is...

  • Page 239

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 240

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate electronic speed control without erasing the set speed memory. Pressing the on/off button or turning the ignition switch off erases the set speed memory. To resu...

  • Page 241

    Pressing the set (-) button once will result in a 1 mph (1.6 km/h) decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph (1.6 km/h). To accelerate for passing press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set...

  • Page 242

    Parksense® will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the on/run position. Parksense® can be active only when the shift lever is in reverse. If parksense® is enabled at this shift lever position, the system will remain active ...

  • Page 243

    Parksense® display when the vehicle is in reverse, the warning display will turn on indicating the system status. Parksense® warning display park assist system on 3 understanding the features of your vehicle 241.

  • Page 244

    The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the evic display will show fewer arcs and the sound tone will change from slow, to fast, to continuous. Park assist system off slow tone 242 und...

  • Page 245

    Fast tone continuous tone 3 understanding the features of your vehicle 243.

  • Page 246

    The vehicle is close to the obstacle when the evic display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) 39-25...

  • Page 247

    Enabling/disabling parksense® parksense® can be enabled and disabled through the customer-programmable features section of the evic. The available choices are: off, sound only, or sound and display. Refer to “electronic vehicle information center (evic)/personal settings (customer-programmable fea- ...

  • Page 248

    If “parksense unavailable wipe rear sen- sors” appears in the electronic vehicle information center (evic) make sure the outer surface and the underside of the rear fascia/bumper is clean and clear of snow, ice, mud, dirt or other obstruction and then cycle the ignition. If the message continues to ...

  • Page 249

    • parksense®, when on, will mute the radio when it is sounding a tone. • clean the parksense® sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The ...

  • Page 250

    Warning! • drivers must be careful when backing up even when using parksense®. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue...

  • Page 251

    Parkview® rear back up camera — if equipped your vehicle may be equipped with the parkview® rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the navigation/multimedia ra...

  • Page 252

    Warning! Drivers must be careful when backing up even when using the parkview® rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your ...

  • Page 253

    4. Enable or disable the rear camera feature by selecting the “enable rear camera in reverse” soft-key. 5. Press the “save” soft-key. Turning parkview® on or off — without navigation/multimedia radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Enable or disable the rear camer...

  • Page 254

    Courtesy/interior lighting at the forward end of the console are two courtesy lights (standard dome light has two buttons). The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with remote keyless entry (rke) the lights will also turn on when th...

  • Page 255

    Sunglass storage (non-sunroof only) at the front of the overhead console, a compartment is provided for the storage of two pairs of sunglasses. From the closed position, press the door latch to open the compartment. The door will slowly rotate to the full open position. From this position, the door ...

  • Page 256

    Note: from the “conversation mirror” position, the door can only be closed. To return to the full open position, the door must first be closed and then opened by pressing the latch again to release. Rear courtesy/reading lights — if equipped the overhead console has two sets of courtesy lights. The ...

  • Page 257

    Rear overhead consoles — if equipped the rear overhead storage system is available in two versions: with or without sunroof. An additional led at the front of the rear console shines down on the front foot-well area while in courtesy mode, for added convenience. Reading lights overhead compartment f...

  • Page 258

    Rear console halo lighting the rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “lights/ halo lights — if equipped” in “understanding the fe...

  • Page 259

    Note: homelink® is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recom...

  • Page 260

    Programming a rolling code for programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “learn” or “train” button located where the hanging antenna is attached to the garage door opener. It is not the button that is normally used to open...

  • Page 261

    2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light in view. 3. Simultaneously press and hold both the homelink® button you want to program and the hand-held trans- mitter button. 4. Continue to hol...

  • Page 262

    Note: if the garage door opener/device does not acti- vate, press the button a third time (for two seconds) to complete the training. To program the remaining two homelink® buttons, repeat each step for each remaining button. Do not erase the channels. Programming a non-rolling code for programming ...

  • Page 263

    Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink® button until the indicator light begins to flash after 20 seconds. Do not release the butto...

  • Page 264

    It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. 1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keepin...

  • Page 265

    Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Press and hold the desired homelink® button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. ...

  • Page 266

    Troubleshooting tips if you are having trouble programming homelink®, here are some of the most common solutions: • replace the battery in the original hand-held transmit- ter. • press the learn button on the garage door opener to complete the training for a rolling code. • did you unplug the device...

  • Page 267

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 268

    Power sunroof — if equipped the power sunroof switch is located between the sun visors on the overhead console. Warning! • never leave children unattended in a vehicle, and do not leave the key in the ignition switch. Occu- pants, particularly unattended children, can be- come entrapped by the power...

  • Page 269

    Opening sunroof — express press the switch rearward and release it within one-half second. The sunroof and sunshade will open automati- cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “express open”. During express open operation, any movement...

  • Page 270

    Venting sunroof — express press and release the vent button within one half second and the sunroof will open to the vent position. This is called “express vent”, and it will occur regardless of sunroof position. During express vent operation, any movement of the switch will stop the sunroof. Sunshad...

  • Page 271

    Ignition off operation for vehicles not equipped with the electronic vehicle information center (evic) the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. For vehicles equipped with t...

  • Page 272

    Note: to ensure proper operation a mopar® cigar knob and element must be used. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • power outlets are designed for ac...

  • Page 273

    On vehicles equipped with the super console the power outlets are located under the retractable cover. To access the power outlets push down on the cover and slide it toward the instrument panel. The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are ...

  • Page 274

    The power outlets include tethered caps, labeled with a key or battery symbol indicating the power source. The power outlet, located on the lower instrument panel, is powered directly from the battery. Items plugged into this power outlet may discharge the battery and/or prevent the engine from star...

  • Page 275

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 276

    Caution! (continued) • power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Improper use of the power outlet can cause damage. Power inverter — if equipped a 110 volt, 150 watt inverter outlet (if equipped) converts dc current t...

  • Page 277

    This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such as playsta- tion3 and xbox360 will exceed this power limit, as will most power tools. The power inverter is designed with built-in overload protection. I...

  • Page 278

    Instrument panel cupholders the instrument panel cupholders are located in a pull-out drawer just above the lower storage bin. Pull the drawer out firmly until it stops, and place the container to be held in either one of the cupholder wells. The cupholders are designed to accommodate a wide variety...

  • Page 279

    For rear passengers two cupholders are located in the pull-out drawer, located in the back of the super console. Pull the drawer out to the first position to use the cupholders. Premium console cupholders — if equipped on models equipped with premium center consoles, there are four cupholders locate...

  • Page 280

    Interior bottle holders there are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommo- dates up to a 20 oz (.6 l) plastic bottle. Warni...

  • Page 281

    Smoker’s package kit — if equipped with the optional authorized dealer-installed smoker’s package kit, a removable ash receiver is inserted into one of the two cupholders in the center front instrument panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rear...

  • Page 282

    Upper glove compartment to open the upper compartment, press in on the button, located on the left side of the upper door. The door will automatically open. To close the compartment door, push downward on the door’s surface to latch the door closed. Lower glove compartment to open the lower compartm...

  • Page 283

    Door trim panel storage front door storage both interior front door panels have multiple pockets for storage. Driver seatback storage — if equipped the driver’s seatback has a primary storage pocket on all models and an optional secondary mesh pocket. Driver’s seatback storage 1 — bag holder 2 — sta...

  • Page 284

    Umbrella holder an umbrella holder has been conveniently molded into the left front door entry scuff molding. Second row seat storage bins — if equipped the seat storage bins are located on the floor in front of the second row seats. The area below the covers can be used for storage when the second ...

  • Page 285

    Caution! Note: the storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. Warning! In a collision, serious injury could result if the seat storage bin covers are not properly latched. • do not drive the vehicle wi...

  • Page 286

    Storage bin safety warning carefully follow these warnings to help prevent personal injury or damage to your vehicle: warning! • always close the storage bin covers when your vehicle is unattended. • do not allow children to have access to the second row seat storage bins. Once in the storage bin, y...

  • Page 287

    Note: in the event of an individual being locked inside the storage bin, the storage bin cover can be opened from inside of the bin by pushing on the glow-in-the-dark lever attached to the storage bin cover latching mecha- nism. Coat hooks coat hooks are located along the headliner for the second an...

  • Page 288

    Note: with all rear seats stowed or removed, 4 x 8 foot sheets of building material will fit on the vehicle floor with the liftgate closed. The front seats must be moved slightly forward of the rearmost position. Console features there are three consoles available: basic, premium and super. Warning!...

  • Page 289

    Basic console basic console features consist of the following: • the basic console profile allows vehicle occupants to easily pass through the first row to the second. • four cupholders accept up to extra large size beverage cups or 20 oz (.6 l) plastic bottles. Cupholders are dishwasher safe for cl...

  • Page 290

    4. Reinstall the clip first and then while pushing down- ward on the console with slight pressure, reinstall the cover plug. 5. Pull up on the console to be sure it is firmly latched. Warning! In an accident, serious injury could result if the removable floor console is not properly installed. Alway...

  • Page 291

    The top and center console sections slide forward and rearward to provide added user comfort. A one-piece cup holder insert for both cavities can easily be removed for cleaning. The cupholders will also accommodate large size cups and 20 oz (.6 l) bottles. Position 1 shows the console closed with fo...

  • Page 292

    Dual storage bins position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console. This provides easy access to the storage area below and provides two of the four cupholders for the second row passengers. Posit...

  • Page 293

    To remove the premium floor console 1. Pull up on the bottom release handle in the front of the console. 2. Lift the rear of the console up several inches/ centimeters. 3. Pull rearward to disengage from floor and remove console. To reinstall the premium floor console: 1. Position the console at a s...

  • Page 294

    4. Push down on the rear of the console until it is seated in the rear floor bracket. 5. Pull up on the console to be sure it is firmly latched. Warning! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console i...

  • Page 295

    Note: the front cupholder light ring and pass through lighting is controlled by a dimming switch located on the instrument panel, refer to “lights” in “understanding the features of your vehicle” for further information. Located in the back of the super console is a storage drawer and cupholders for...

  • Page 296

    Ram cargo van features ram cargo van load floor the ram cargo van receives a structural aluminum rear load floor. Two load floor options are available, the standard floor with a flat aluminum surface and non skid strips or an optional deluxe floor with a flat aluminum surface and non skid strips, th...

  • Page 297

    Standard load floor deluxe load floor storage bin locations (rear view) 3 understanding the features of your vehicle 295.

  • Page 298

    Rear window features rear window defroster the rear window defroster button is located on the climate control (mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is...

  • Page 299

    Note: • you can turn off the heated mirror feature at anytime by pressing the rear window defroster switch a second time. • to prevent excessive battery drain, use the rear win- dow defroster only when the engine is operating. Caution! Failure to follow these cautions can cause damage to the heating...

  • Page 300

    Load leveling system — if equipped the automatic load leveling system will provide a level- riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6...

  • Page 301

    The crossbars and side rails are designed to carry weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Note: • crossbars are error-proofed and cannot be deployed or stowed in the incorrect pos...

  • Page 302

    Caution! Use care when removing and handling the crossbars to prevent damage to the vehicle. Bend the crossbar supports at each end, taking care to keep hand clear of pivoting joint. Slide the thumb screw down. Loosening crossbars 300 understanding the features of your vehicle.

  • Page 303

    Then, position the crossbars across the roof. Note: the crossbars are identical and can be placed in any two of the three deploy positions. Stowed position deployed position 3 understanding the features of your vehicle 301.

  • Page 304

    Make sure the directional arrows on the crossbars align with the directional arrows on the side rails. Set the crossbars into the deployed positions. Once the crossbars are set into position, tighten the thumb screws completely. Deploy positions – choose two of three crossbar to side rail installati...

  • Page 305

    Stowing the crossbars reverse the procedure to stow the crossbars, again, taking care to keep hand clear of pivoting joint. Crossbars are identical and can be stowed in either rail nest. Once the crossbars are stowed, tighten the thumb screws completely. Note: load should always be secured to crossb...

  • Page 306

    Caution! • check deployed crossbars frequently and retighten thumb screws as necessary. (continued) caution! (continued) • to avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lb (68 kg). Always distribute heavy loads as evenly as possible and secure...

  • Page 307

    Caution! (continued) • long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof ra...

  • Page 308

    Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window. Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window. To lower the sun screen, ...

  • Page 309: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .312 䡵 instrument cluster — base . . . . . . . . . .313 䡵 instrument cluster — premium . . . . . . .314 䡵 instrument cluster descriptions . . . . .315 䡵 electronic vehicle information center (evic) — if equipp...

  • Page 310

    䡵 uconnect® 730n/430/430n cd/dvd/hdd/ nav — if equipped . . . . . . . . . . . . . . . . . . .353 ▫ operating instructions (voice command system) — if equipped . . . . . . . . . . . . . . . . .353 ▫ operating instructions (uconnect® phone) — if equipped. . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 311

    ▫ play mode . . . . . . . . . . . . . . . . . . . . . . . . . .383 ▫ list or browse mode . . . . . . . . . . . . . . . . . . .385 ▫ bluetooth streaming audio (btsa) . . . . . . . . .387 䡵 uconnect® multimedia — video entertainment system (ves™) — if equipped. . . . . . . . . . . . . . . . . . . . . ...

  • Page 312

    ▫ headphones operation . . . . . . . . . . . . . . . . .412 ▫ blu-ray headphones operation . . . . . . . . . . . .413 ▫ controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .414 ▫ replacing the headphone batteries. . . . . . . . .415 ▫ unwired® stereo headphone lifetime limited warranty . ...

  • Page 313

    ▫ rear manual climate control — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .443 ▫ automatic temperature control (atc) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .446 ▫ summer operation . . . . . . . . . . . . . . . . . . . .458 ▫ winter operation. . . . . . . . . ...

  • Page 314

    Instrument panel features 1 — air vents 5 — upper glove compartment 9 — storage bin 13 — hood release 2 — instrument cluster 6 — lower glove compart- ment 10 — cup holders 14 — dimmer switch 3 — shift lever 7 — climate controls 11 — switch bank 15 — headlight switch 4 — radio 8 — dvd – if equipped 1...

  • Page 315

    Instrument cluster — base 4 understanding your instrument panel 313.

  • Page 316

    Instrument cluster — premium 314 understanding your instrument panel.

  • Page 317

    Instrument cluster descriptions 1. Tachometer this gauge measures engine revolutions per minute (rpm x 1000). Before the pointer reaches the red area, ease up on the accelerator to prevent engine damage. 2. Front fog light indicator — if equipped this indicator will illuminate when the front fog lig...

  • Page 318

    Odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repai...

  • Page 319

    Note: some of the above warnings will be displayed in the electronic vehicle information center display area located in the instrument cluster. Refer to ”electronic vehicle information center (evic) display — if equipped” for further information. Low tire when the appropriate condition exists, the o...

  • Page 320

    Unless reset, this message will continue to display each time you turn the ignition switch to the on/run position. To turn off the message temporarily, press and release the step button on the steering wheel. To reset the oil change indicator system (after performing the scheduled maintenance), perf...

  • Page 321

    If the abs light is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the abs light does not turn on when the ignition switch is turned to the on/run position, have the light inspected by an authorized dealer. 8. Tire pressure monitoring tell...

  • Page 322

    Illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur for a variety of reasons, includi...

  • Page 323

    9. Malfunction indicator light (mil) the malfunction indicator light (mil) is part of an onboard diagnostic system, called obd, that monitors engine and automatic transmission con- trol systems. The light will illuminate when the key is in the on/run position, before engine start. If the bulb does n...

  • Page 324

    10. Electronic stability control (esc) activation/ malfunction indicator light — if equipped the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is turned to the on/run position. It should go out with the engine running. If the “esc activa...

  • Page 325

    11. Electronic stability control (esc) off indicator light — if equipped this light indicates the electronic stability con- trol (esc) is off. 12. Speedometer indicates vehicle speed. 13. Fuel door reminder the arrow in this symbol is a reminder that the fuel filler door is located on the left side ...

  • Page 326

    16. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: • you must apply the brakes before shifting from park. • the highest available transmission gear is displayed in the lower right cor...

  • Page 327

    In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the abs pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the ev...

  • Page 328

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 19. Seat belt reminder light when the ignition switch is first turned to o...

  • Page 329

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “maintaining your vehicle”. Follow the warnings unde...

  • Page 330

    23. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate...

  • Page 331

    If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rou...

  • Page 332

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. This system conveniently allows the driver to select a variety of useful information by pressing the switches...

  • Page 333

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: up button press and release the up button to scroll up- ward through the main menus (fuel economy, vehicle info, tire psi, cruise, messages, units, system setup) and sub-menus. Down bu...

  • Page 334

    Back button press the back button to scroll back to a previous menu or sub-menu. Electronic vehicle information center (evic) displays the evic display consists of three sections: 1. The top line where compass direction, odometer line and outside temperature are displayed. 2. The main display area w...

  • Page 335

    • unstored messages this message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are ⬙turn signal on⬙ (if a turn signal is left on) and ⬙lights on⬙ (if driver leaves the vehicle). • unstored messages until run these messages ...

  • Page 336

    • vehicle not in park • press brake pedal and push button to start • door(s) ajar (with a single chime, if vehicle is in motion) • liftgate ajar (chime will sound when vehicle starts moving) • low tire pressure • service tpm system (refer to “tire pressure monitor- ing system” in “starting and opera...

  • Page 337

    • blind spot system not available — this message is displayed to indicate the blind spot monitor (bsm) system is temporarily unavailable due to sensor block- age, electronic interference, or other ⬙temporary⬙ con- ditions. When this message is displayed both outside rear view icons will be illuminat...

  • Page 338

    • electronic speed control set this light will turn on when the electronic speed control is set. For further information, refer to “electronic speed control” in “under- standing the features of your vehicle.” evic amber telltale lights this area will show reconfigurable amber caution tell- tales. Th...

  • Page 339

    Evic red telltale lights this area will show reconfigurable red telltales. These telltales include: • door ajar this light will turn on to indicate that one or more doors may be ajar. • oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when...

  • Page 340

    • electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. The light will come on when the ignition is first turned on and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked b...

  • Page 341

    • transmission temperature warning light this light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmission into neutral and run the engine ...

  • Page 342

    Unless reset, this message will continue to display each time you turn the ignition switch to the on/run position. To turn off the message temporarily, press and release the menu button. To reset the oil change indicator system (after performing the scheduled maintenance), perform the following step...

  • Page 343

    Average fuel economy display distance to empty (dte) this display shows the estimated distance that can be traveled with the fuel remaining in the tank. This esti- mated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank lev...

  • Page 344

    Vehicle speed press and release the up or down button until “vehicle speed” displays highlighted in the evic and press the select button. Press the select button to display the current speed in mph or km/h. Pressing the select button a second time will toggle the unit of measure between mph or km/h....

  • Page 345

    Tire psi press and release the up or down button until “tire psi:” displays highlighted in the evic. Press the select button to view a graphic of the vehicle with a tire pressure value at each corner of the graphic. Units press and release the up or down button until “units” displays highlighted in ...

  • Page 346

    Messages # select from main menu using the up or down buttons. This feature shows the number of stored warning mes- sages (in the # place holder). Pressing the select button will allow you to see what the stored messages are. Press and release the up and down buttons if there is more than one messag...

  • Page 347

    Manual compass calibration if the compass appears erratic and the cal indicator does not appear in the evic display, you must put the compass into the calibration mode manually, as follows: 1. Turn on the ignition switch. 2. Press the up or down button until the setup (customer-programmable features...

  • Page 348

    Compass variance map 1. Turn the ignition switch on. 2. Press the up or down button until the setup (customer-programmable features) menu is reached, then press the select button. 3. Press the down button until the “compass variance” message is displayed in the evic, then press the select button. Th...

  • Page 349

    Press and release the up or down button until ⬙system setup ⬙ is highlighted in the main menu of the evic. Then press the select button to enter the system setup sub-menu. Press and release the up or down button to select a feature form the following choices: select language when in this display you...

  • Page 350

    Refer to “rear park assist system” in “understanding the features of your vehicle” for system function and operating information. Auto unlock doors – if equipped when on is selected, all doors will unlock when the vehicle is stopped and the transmission is in the park or neutral position and the dri...

  • Page 351

    Remote start comfort sys. – if equipped when this feature is selected and the remote start is activated, the heated steering wheel and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote st...

  • Page 352

    A check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Headlamp off delay when this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the ...

  • Page 353

    Intermittent wiper options — if equipped when on is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield. To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been a...

  • Page 354

    Next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Easy entry/exit seat – if equipped this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your se...

  • Page 355

    Mode, in this mode the blind spot monitor (bsm) will show a visual alert in the outside mirrors as well as an audible alert when the turn signal is on. When “blind spot alert off” is selected the blind spot monitor (bsm) system is deactivated. To make your selection, press and release the select but...

  • Page 356

    Uconnect® 130 operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electron...

  • Page 357

    Time button press the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, press the right side tune/ s...

  • Page 358

    Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary tune/scroll control knob a fourth time and balance will display. Turn the tune/ scroll control knob to the r...

  • Page 359

    And 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to ...

  • Page 360

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 361

    Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pressing and holding the seek ...

  • Page 362

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 363

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 364

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 365

    Uconnect® 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to tur...

  • Page 366

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 367

    Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the mi...

  • Page 368

    Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control...

  • Page 369

    Toggle the music type button to select the following format types: program type 16-digit character dis- play no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news ne...

  • Page 370

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 371

    And 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to ...

  • Page 372

    If you insert a disc with the ignition on/run and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player wil...

  • Page 373

    Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pressing and holding the seek ...

  • Page 374

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 375

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 376

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 377

    Info button (cd mode for mp3 play) pressing the info button repeatedly will scroll through the following tag information: song title, artist, file name, and folder name (if available). Press the info button once more to return to ⬙elapsed time ⬙ priority mode. Press and hold the info button for thre...

  • Page 378

    Sports, news, entertainment, and programming for chil- dren, directly from its satellites and broadcasting studios. Note: sirius service is not available in hawaii and has limited coverage in alaska. System activation sirius satellite radio service is pre-activated, and you may begin listening immed...

  • Page 379

    Selecting uconnect® (satellite) mode press the sat button until ⬙sat⬙ appears in the display. A cd may remain in the radio while in the satellite radio mode. Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within...

  • Page 380

    Operating instructions - uconnect® (satellite) mode note: the ignition switch must be in the on/run or acc position to operate the radio. Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch to seek do...

  • Page 381

    Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Toggle the music type button again to select the music type. ...

  • Page 382

    You may add a second channel to each pushbutton by repeating the above procedure with this exception: press the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2. This allows a total of 12 satellite channels to be stored into pushbutton memory. Th...

  • Page 383

    Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support the ipod® control features. Please visit apple’s website for software updates. Note: • if the radio has a usb port, refer to the appropriate uconnect® multimedia radio user’...

  • Page 384

    Note: the glove compartment will have a position where the ipod® or consumer electronic audio device cable can be routed through without damaging the cable when closing the lid. This allows routing of the cable without damaging it while closing the lid. If a cut out is not available in the glove com...

  • Page 385

    Controlling the ipod® or external usb device using radio buttons to get into the ipod®/usb/mp3 control mode and access a connected audio device, either press the “aux” button on the radio faceplate or press the vr button and say ⬙usb⬙ or ⬙switch to usb⬙. Once in the ipod®/usb/ mp3 control mode, audi...

  • Page 386

    • use the seek and seek>> buttons to jump to the previous or next track. Pressing the seek>> button during play mode will jump to the next track in the list, or press the vr button and say ⬙next or previous track ⬙. • while a track is playing, press the info button to see the associated metadata (ar...

  • Page 387

    List or browse mode during play mode, pressing any of the buttons described below, will bring up list mode. List mode enables scrolling through the list of menus and tracks on the audio device. • tune control knob: the tune control knob functions in a similar manner as the scroll wheel on the audio ...

  • Page 388

    • list button: the list button will display the top level menu of the ipod® or external usb device. Turn the tune control knob to list the top-menu item to be selected and press the tune control knob. This will display the next sub-menu list item on the audio device, then follow the same steps to go...

  • Page 389

    Bluetooth streaming audio (btsa) music can be streamed from your cellular phone to the uconnect® phone system. Controlling btsa using radio buttons to enter btsa mode, press either “aux” button on the radio or press the vr button and say “bluetooth stream- ing audio”. Play mode when switched to btsa...

  • Page 390

    Browse browsing is not available on a bluetooth streaming audio (btsa) device. Only the current song that is playing will display info. Uconnect® multimedia — video entertainment system (ves™) — if equipped getting started • screen(s) located in the overhead console: unfold the overhead lcd screen(s...

  • Page 391

    • turn on the player (if equipped on dual screen sys- tem) by pushing the power button, located on the far left, or by pressing the button on the remote control. • when the video screen(s) are open and a dvd/blu- ray disc is inserted into the ves™ player, the screen(s) turn(s) on automatically, the ...

  • Page 392

    Using the remote control • select an audio channel (channel 1 for 2nd row screen and channel 2 for 3rd row screen), then press the source key and select ves™ disc from the menu. • press popup/menu key to navigate disc menu and options. Note: due to the size of the content on a blu-ray disc, the disc...

  • Page 393

    When connecting an external source to the aux input, be sure to follow the standard color coding for the ves™ jacks: note: certain high-end video games, such as playsta- tion3 and xbox360 will exceed the power limit of the vehicle’s power inverter. Refer to the power inverter section in your vehicle...

  • Page 394

    2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 soft-key and then touch either aux 1 or aux 2 in the ves column (depending which aux input is used). To exit press the...

  • Page 395

    Listen to an audio source on channel 2 while a video is playing on channel 1 ensure the remote control and headphone switch is on channel 2. Using the remote control 1. Press the source button on the remote control and the mode select screen will display, unless a video is playing then only a small ...

  • Page 396

    2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. To listen to an audio source on channel 2 while a video is playing on channel 1, touch the 2 soft-key and choose an audio source. ...

  • Page 397

    Dual video screen note: typically there are two different ways to operate the features of the video entertainment system (ves™). • the remote control • the touch-screen radio (if equipped) play a dvd using the touch-screen radio note: headunit dvd player does not play blu-ray discs. 1. Press the ope...

  • Page 398

    Note: • channel/screen 1 select mode information is shown on the left side of the screen. • channel/screen 2 select mode information is shown on the right side of the screen. • the ves™ will retain the last setting when turned off. Using the touch-screen radio controls 1. Press the menu hard-key on ...

  • Page 399

    3. Touch the 1 or 2 soft-key and then the disc soft-key in the media column. To exit touch the back arrow at the top left of the screen. Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key and then the view video soft-key. • vie...

  • Page 400

    Play a dvd using the ves™ player (if equipped) 1. Insert the dvd with the label facing up. The ves™ player automatically selects the appropriate mode after the disc is recognized and starts playing the dvd. Note: the ves™ player has basic dvd control func- tion such as menu, play, pause, ff, rw and ...

  • Page 401

    Note: • channel/screen 1 select mode information is shown on the left side of the screen. • channel/screen 2 select mode information is shown on the right side of the screen. • the ves™ will retain the last setting when turned off. Using the touch-screen radio controls 1. Press the menu hard-key on ...

  • Page 402

    Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key and then the view video soft-key. • viewing a dvd on the touch-screen radio screen is not available in all states/provinces. If available, the vehicle must be stopped and the s...

  • Page 403

    Play a blu-ray disc using the blu-ray player (if equipped) 1. Insert the blu-ray disc with the label facing up. The blu-ray player automatically selects the appropriate mode after the disc is recognized and starts playing the blu-ray disc. Note: the blu-ray player has basic control functions such as...

  • Page 404

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves™ soft-key to display the rear ves™ controls. If a channel list is displayed, touch the hide list soft-key to display the rear ves™ controls screen. 3. Touch the 1 or 2 soft-key and then the...

  • Page 405

    Listen to an audio source while a video is playing ensure the remote control and headphone switch are on the same channel. If watching a video on screen 1 (second row), then channel 2 could be used for audio. If watching a video on screen 2 (third row), then channel 1 could be used for audio. Using ...

  • Page 406

    2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. To listen to an audio source on channel 2 while a video is playing on channel 1, touch the 2 soft-key and choose an audio source. ...

  • Page 407

    Important notes for dual video screen system • ves is able to transmit two channels of stereo audio and video simultaneously. • the blu-ray disc player can play cds, dvds and blu-ray discs. • the dvd player can play cds and dvds. • in split screen mode the left side equates to channel 1 and the righ...

  • Page 408

    Ves™ remote control – if equipped controls and indicators 1. Power – turns the screen and wireless headphone transmitter for the selected channel on or off. To hear audio while the screen is closed, press the power button to turn the headphone transmitter on. 2. Channel selector indicators – when a ...

  • Page 409

    6. 䉲 / prev – in radio modes, press to select to the previous station. In disc modes, press to advance to the start of the current or previous audio track or video chapter. In menu modes, use to navigate in the menu. 7. Pop up/menu – press to return to the main menu of a dvd disc, to select a satell...

  • Page 410

    12. Slow – if equipped – press to slow playback of a dvd disc. Press play ( 䉴) to resume normal play. 13. Status – if equipped – press to display the current status. 14. Mode/source – press to change the mode of the selected channel. See the mode selection section of this manual for details on chang...

  • Page 411

    Blu-ray player remote control – if equipped controls and indicators 1. Power – turns the screen and wireless headphone transmitter for the selected channel on or off. To hear audio while the screen is closed, press the power button to turn the headphone transmitter on. 2. Channel selector indicators...

  • Page 412

    7. 䉴䉴 – press and release to jump to the next available audio track or video chapter. Press and hold to fast forward through the current audio track or video chapter. 8. 䉴 / 㥋 (play/pause) – begin/resume or pause disc play. 9. Four colored buttons – press to access blu-ray disc features. 10. Popup/m...

  • Page 413

    Remote control storage the video screen(s) come with a built in storage compart- ment for the remote control which is accessible when the screen is opened. To remove the remote, use your index finger to pull and rotate the remote towards you. Do not try to pull the remote straight down as it will be...

  • Page 414

    Locking the remote control all remote control functionality can be disabled as a parental control feature. • to disable the remote control from making any changes, press the video lock button on the dvd player (if equipped). If the vehicle is not equipped with a dvd player, follow the radio’s instru...

  • Page 415

    Blu-ray headphones operation the headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to do...

  • Page 416

    Controls the headphone power indicator and controls are located on the right ear cup. Note: the rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video sys...

  • Page 417

    Note: • when both switches are on channel 1, the remote is controlling channel 1 and the headphones are tuned to the audio of the ves™ channel 1. • when both switches are on channel 2, the remote is controlling channel 2 and the headphones are tuned to the audio of the ves™ channel 2. 2. Press the s...

  • Page 418

    Unwired® stereo headphone lifetime limited warranty who does this warranty cover? This warranty covers the initial user or purchaser ( ⬙you⬙ or ⬙your⬙) of this particular unwired technology llc ( ⬙unwired⬙) wire- less headphone ( ⬙product⬙). The warranty is not transfer- able. How long does the cove...

  • Page 419

    What will unwired® do? Unwired®, at its option, will repair or replace any defective product. Unwired® re- serves the right to replace any discontinued product with a comparable model. This warranty is the sole warranty for this product, sets forth your exclusive remedy regarding defective products,...

  • Page 420

    The ves™ has the ability to switch tuner (am/fm), seek, scan, tune, and recall presets in radio modes as long as it is not in shared mode. When in shared disc mode both the radio and the ves™ have control of the video functions. The ves™ has the ability to control the following video modes: 1. Cd: a...

  • Page 421

    4. Channel 2 mode 5. Channel 2 shared status 6. Channel 2 audio only/mute 7. Channel 1 enter/ok button action 8. Channel 2 enter/ok button action 9. Clock 10. Video lock 11. Not available / error numeric keypad menu when the display for either channel 1 or channel 2 shows direct tune, pressing the r...

  • Page 422

    Makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Press the remote control’s navigation buttons ( 䉱, 䉲, 䉴, 䉳) to navigate to the desired digit. 2. When the digit is highlighted, press the remote con- trol’s enter/ok button to select...

  • Page 423

    Disc menu when listening to a cd audio or cd data disc, pressing the remote control’s pop up/menu button displays a list of all commands which control playback of the disc. Using the options you can activate or cancel scan play and random play. Display settings when watching a video source (dvd vide...

  • Page 424

    Listening to audio with the screen closed to listen to only audio portion of the channel with the screen closed: • set the audio to the desired source and channel. • close the video screen. • to change the current audio mode, press the remote control’s source button. This will automatically se- lect...

  • Page 425

    The blu-ray player is capable of the playing the follow- ing types of discs (12 cm diameter): • bd: bdmv (profile 1.1), bdav (profile 1.1), • dvd: dvd-video, dvd-audio, avcrec, avchd, dvd-vr • cd: cd-da, vcd, cd-text • dvd/cd: mp3, wma, aac, divx (versions 3 – 6) profile 3.0 dvd/bd region codes the ...

  • Page 426

    If you record a disc using a personal computer, there may be cases where the ves™ dvd player may not be able to play some or the entire disc, even if it is recorded in a compatible format and is playable on other players. To help avoid playback problems, use the following guide- lines when recording...

  • Page 427

    Compressed audio files (mp3 and wma) the dvd player is capable of playing mp3 (mpeg-1 audio layer 3) and wma (windows media audio) files from a cd data disc (usually a cd-r or cd-rw). • the dvd player always uses the file extension to determine the audio format, so mp3 files must always end with the...

  • Page 428

    Disc errors if the dvd player is unable to read the disc, a ⬙disc error⬙ message is displayed on the ves™ and radio displays and the disc is automatically ejected. A dirty, damaged, or incompatible disc format are all potential causes for a ⬙disc error⬙ message. If a disc has a damaged track which r...

  • Page 429

    Display other language setup all of the language settings have a special ⬙other⬙ setting to accommodate languages other than japanese or eng- lish. These languages are selected using a special four- digit code. To enter a new language code, activate the dvd setup menu. To enter dvd setup menu stop t...

  • Page 430

    • using the remote control up and down cursor but- tons, select a digit for the current position. After selecting the digit, press the remote control’s right cursor button to select the next digit. Repeat this digit selection sequence for all four digits. • when the entire four-digit code is entered...

  • Page 431

    Not all dvd discs encode a rating, so it is still possible that discs designed for adult audiences can still play without requiring a password. The default rating is level 8 (play all discs without a password) and the default password is 0000. Dvd password entry 4 understanding your instrument panel...

  • Page 432

    To set the password, activate the dvd setup menu and follow these additional instructions: • using the remote control left and right cursor but- tons, select the rating tab. • highlight ⬙change password⬙, and then press the remote control’s enter/ok button. • enter the current password. Select a dig...

  • Page 433

    To set the rating, activate the dvd setup menu and follow these additional instructions: • using the remote control’s left and right cursor buttons, select the rating tab. • highlight ⬙change rating⬙, and then press the remote control’s enter/ok button. • enter the current password. Select a digit, ...

  • Page 434

    Product agreement software this product contains software licensed under gnu general public license (gpl) or gnu lesser general public license (lgpl), etc. You have the right of acqui- sition, modification, and distribution of the source code of the gpl/lgpl software. You may download source code fr...

  • Page 435

    And/or (ii) decode vc-1 video that was encoded by a consumer engaged in a per- sonal and non-commercial activity and/or was obtained from a video pro- vider licensed to provide vc-1 video. No license is granted or shall be implied for any other use. Additional information may be obtained from mpeg l...

  • Page 436

    • manufactured under license under u.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other u.S. And worldwide patents issued & pending. Dts is a registered trademark and the dts logos, symbol and dts 2.0 channel are trademarks of dts, inc. © 1996-2007 dts, inc. All rights rese...

  • Page 437

    Steering wheel audio controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel, at the three and nine o’clock positions. The right-hand rocker switch has a pushbutton in the center, and controls the volume and mode of the sound system. Pressing the...

  • Page 438

    Radio operation pressing the top of the switch will seek up for the next listenable station, and pressing the bottom of the switch will seek down for the next listenable station. The button located in the center of the left-hand switch will tune to the next preset station that you have pro- grammed ...

  • Page 439

    Note: if you experience difficulty in playing a particular disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile phone...

  • Page 440

    When the front control is in any position other than rear, the front control operates all the rear functions. The rear airflow modes will mirror the front unit opera- tion. Rear panel mode is automatically selected when the front control is in the panel mode. When the front unit is in bi-level mode,...

  • Page 441

    2. Rear blower control — if equipped • use this control to regulate the amount of air forced through the rear system in any mode you select. The rear blower speed increases as you move the control to the right from the “o” (off) position. There are seven blower speeds. To allow the rear overhead con...

  • Page 442

    6. Mix mode air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort, while reducing moisture on the windshield. 7. Front defrost mode air is ...

  • Page 443

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 444

    • in cold or damp weather, the use of the recirculation mode will cause windows to fog on the inside because of moisture buildup inside the vehicle. For maximum defogging, select the outside air position. • in order to prevent fogging, when the recirculation button is pressed and the mode control is...

  • Page 445

    Note: there is a difference in temperature (in any conditions other than full cold or full hot), between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. 13. Panel mode button air is directe...

  • Page 446

    Rear blower control the primary control for the rear blower is on the front climate control unit, located on the instrument panel. Only when the front control for the rear blower is in the rear position do the second row seat occupants have control of the rear blower speed. The rear blower control, ...

  • Page 447

    Caution! (continued) just behind the sliding door. Do not block or place objects directly in front of the inlet grille or heater outlets. The electrical system could overload, causing damage to the blower motor. Rear temperature control the rear mode selection rear, allows the settings to be control...

  • Page 448

    Automatic temperature control (atc) — if equipped • front three-zone atc allows both driver and front passenger seat occupant, and rear seat occupants to select individual comfort settings. • when occupants in the vehicle select the auto mode operation, a comfort temperature can be set by using the ...

  • Page 449

    1. Air conditioning (a/c) button press and release to change the current air conditioning (a/c) setting, the indicator illuminates when a/c is on. Performing this function will cause the atc to switch into manual mode. 2. Left front seat occupant temperature display this display shows the temperatur...

  • Page 450

    10. Rear control button provides toggle operation between front control screen and rear control screen. Push the button to activate the rear climate control screen and allow the front seat occupants control over the rear climate settings. 11. Rear lock press and release the rear lock button on the f...

  • Page 451

    16. Recirculation control button press and release to change the current setting, the indicator illuminates when on. 17. Sync button press and release to control the temperature setting for all three zones from the driver temperature control. 18. Driver temperature control up/down button provides th...

  • Page 452

    3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experi- ence the greatest efficiency by simply allowing the system to function automatically. Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system au...

  • Page 453

    • air conditioning (a/c) the air conditioning (a/c) button allows the operator to manually activate or deactivate the air conditioning system. When in a/c mode and the atc is set to a cool temperature, dehumidified air flows through the air outlets. If economy mode is desired, press the a/c button t...

  • Page 454

    1. Mode display this display shows the current mode selection. 2. Rear temperature display this display shows the temperature setting for the rear seat occupants. 3. Blower control display this display shows the current blower speed selection. 4. Rear auto indicator this indicates when the system is...

  • Page 455

    Rear mode control headliner mode air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vanes of the outlets to one side will shut off the airflow. Bi-level mode air comes from both the headliner outlets and the floor...

  • Page 456

    1. Press the rear temperature lock button on the front atc panel. This turns off the rear temperature lock icon in the rear temperature knob. 2. Rotate the rear blower, rear temperature and the rear mode control knobs to suit your comfort needs. 3. Atc is selected by adjusting the rear blower knob c...

  • Page 457

    Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to provide comfort as quickly as possible. • the temperature can be displayed in english or metric units by selecting the “display units of meas...

  • Page 458

    Rear temperature control to change the temperature in the rear of the vehicle, rotate the temperature knob counterclockwise to lower the temperature, and clockwise to increase the tempera- ture. The rear temperature settings are displayed in the front atc panel. When rear controls are locked by the ...

  • Page 459

    • bi-level mode air comes from both the headliner outlets and the floor outlets. Note: in many temperature positions, the bi-level mode is designed to provide cooler air out of the head- liner outlets and warmer air from the floor outlets. • floor mode air comes from the floor outlets. Recirculation...

  • Page 460

    Summer operation the engine cooling system must be protected with a high-quality antifreeze coolant to provide proper corro- sion protection and to protect against engine overheating. A solution of 50% ethylene glycol antifreeze coolant and 50% water is recommended. Refer to “maintenance pro- cedure...

  • Page 461

    Window fogging vehicle windows tend to fog on the inside in mild, rainy and/or humid weather. To clear the windows, select defrost or mix mode and increase the front blower speed. Do not use the recirculation mode without a/c for long periods, as fogging may occur. Outside air intake make sure the a...

  • Page 462

    Operating tips chart 460 understanding your instrument panel.

  • Page 463: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .465 ▫ automatic transmission . . . . . . . . . . . . . . . .465 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .465 ▫ extreme cold weather (below –20°f or −29°c) . . . . . . . . . . . . . . . . . . . ....

  • Page 464

    䡵 power steering . . . . . . . . . . . . . . . . . . . . .485 ▫ power steering fluid check . . . . . . . . . . . . . .486 䡵 parking brake . . . . . . . . . . . . . . . . . . . . . .487 䡵 anti-lock brake system (abs) . . . . . . . . .489 ▫ anti-lock brake warning light. . . . . . . . . . . .491 䡵 ele...

  • Page 465

    ▫ compact spare tire – if equipped . . . . . . . . .520 ▫ full size spare – if equipped . . . . . . . . . . . . .520 ▫ limited-use spare – if equipped . . . . . . . . . .521 ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . .522 ▫ tread wear indicators . . . . . . . . . . . . . . . . . ....

  • Page 466

    ▫ selection of engine oil for flexible fuel vehicles (e-85) and gasoline vehicles . . . . . . .545 ▫ starting . . . . . . . . . . . . . . . . . . . . . . . . . . . .545 ▫ cruising range . . . . . . . . . . . . . . . . . . . . . . .545 ▫ replacement parts . . . . . . . . . . . . . . . . . . . .546 ▫ ...

  • Page 467

    Starting procedures before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your ve...

  • Page 468

    3. If the engine fails to start, the starter will disengage automatically in 10 seconds. If this occurs, turn the ignition switch to the off position, wait 10 to 15 seconds, then repeat the “normal starting” procedure (steps 1–3 above). Note: this vehicle is equipped with a transmission shift interl...

  • Page 469

    Warning! (continued) • if the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly. Refer to “jump starting” in “what to do in emergen- cies” for further informa...

  • Page 470

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 471

    Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift ...

  • Page 472

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 473

    Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the transmission shifter in park unless the brakes are applied. To shift the transmission out of park, the engine must be running and the brake pedal must be pressed....

  • Page 474

    When the fuel economy (econ) mode is engaged, the vehicle control systems will change the following: • the transmission will upshift sooner and downshift later. • the transmission will skip select gears during shifts to allow the engine to operate at lower speeds. • the torque converter clutch will ...

  • Page 475

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has only park, reverse, neutral, and drive shift positions. Manual down- shifts can...

  • Page 476

    Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. When parking on a level surface, you may shift the transmissio...

  • Page 477

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 478

    Warning! (continued) • allowing children to be alone in a vehicle unat- tended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the park- ing brake, brake pedal or the shift lever. • do not leave the key fob in or n...

  • Page 479

    Reverse this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift ...

  • Page 480

    Drive this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through underdrive first, second, third, and fourth gears, direct fifth gear and overdrive sixth gear. The drive ...

  • Page 481

    Park, reverse, and neutral will continue to oper- ate. The malfunction indicator light (mil) may be illu- minated. Limp home mode allows the vehicle to be driven to an authorized dealer for service without dam- aging the transmission. In the event of a momentary problem, the transmission can be rese...

  • Page 482

    You can switch between drive and ers mode at any vehicle speed. When the shift lever is in the drive position, the transmission will operate automatically, shifting between all available gears. Tapping the shift lever to the left (-) will activate ers mode, display the current gear in the instrument...

  • Page 483

    Note: to select the proper gear position for maximum deceleration (engine braking), tap the shift lever to the left (-) repeatedly as the vehicle slows. The transmission will shift to the range from which the vehicle can best be slowed down. Overdrive operation the automatic transmission includes an...

  • Page 484

    Driving on slippery surfaces acceleration rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the driving wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. Warning! ...

  • Page 485

    Driving through water driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow...

  • Page 486

    Caution! (continued) • driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.E., engine oil, trans- mission, axle, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through stan...

  • Page 487

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 488

    Power steering fluid check checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an aut...

  • Page 489

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the park position. The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal ful...

  • Page 490

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 491

    Caution! If the brake system warning light remains on with the parking brake released, a brake system malfunc- tion is indicated. Have the brake system serviced by an authorized dealer immediately. Anti-lock brake system (abs) the anti-lock brake system (abs) provides increased vehicle stability and...

  • Page 492

    Warning! • the anti-lock brake system contains sophisti- cated electronic equipment that may be susceptible to interference caused by improperly installed, or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equ...

  • Page 493

    Anti-lock brake warning light the “anti-lock brake warning light” moni- tors the anti-lock brake system. The light will come on when the ignition switch is turned to the on position and may stay on for as long as four seconds. If the “anti-lock brake warning light” remains on or comes on while drivi...

  • Page 494

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes the traction control system (tcs), brake assist system (bas) and electronic stability control (esc), trailer sway control (tsc), and hill start assist (hsa). These systems compleme...

  • Page 495

    Warning! (continued) • the tcs cannot prevent collisions, including those resulting from excessive speed in turns, or hydro- planing. • the capabilities of a tcs-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of othe...

  • Page 496

    Electronic stability control (esc) the electronic stability control (esc) enhances direc- tional control and stability of the vehicle under various driving conditions. Esc corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the ov...

  • Page 497

    Warning! (continued) resulting from loss of vehicle control due to inappro- priate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an esc equipped vehicle must never be exploited in a reckless or dangerous manner which could jeo...

  • Page 498

    Traction. To turn esc on again, momentarily press the “esc off” switch. This will restore the normal “esc on” mode of operation. Warning! • when in ⴖpartial offⴖ mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the ⴖesc o...

  • Page 499

    Light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. The “esc activation/malfunction indicator light” (lo- cate...

  • Page 500

    Trailer sway control (tsc) tsc uses sensors in the vehicle to recognize an exces- sively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appro- priate wheel(s) to counteract the sway of the trailer. Tsc ...

  • Page 501

    Hill start assist (hsa) the hsa system is designed to assist the driver when starting a vehicle from a stop on a hill. Hsa will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply th...

  • Page 502

    Hsa will work in reverse and all forward gears when the activation criteria have been met. The system will not activate if the vehicle is placed in neutral or park. Warning! There may be situations on minor hills (i.E., less than 8%), with a loaded vehicle, or while pulling a trailer, when the syste...

  • Page 503

    7. Press the “esc off” switch (located in the lower switch bank below the climate controls) four times within 20 seconds. The “esc activation/malfunction indicator light” should turn on and turn off two times. 8. Rotate the steering wheel back to center and then an additional half-turn to the right....

  • Page 504

    Warning! (continued) • hsa is not a parking brake. If you stop the vehicle on a hill without putting the transmission in park and using the parking brake, it will roll down the hill and could cause a collision with another ve- hicle or object. Always remember to use the park- ing brake while parking...

  • Page 505

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 506

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 215 ...

  • Page 507

    Example: r = construction code — ⬙r⬙ means radial construction — ⬙d⬙ means diagonal or bias construction 15 = rim diameter in inches (in) service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of spee...

  • Page 508

    Example: load identification: ⴖ....Blank....ⴖ = absence of any text on the sidewall of the tire indicates a standard load (sl) tire extra load (xl) = extra load (or reinforced) tire light load (ll) = light load tire c, d, e, f, g = load range associated with the maximum load a tire can carry at a sp...

  • Page 509

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 510

    Example: dot ma l9 abcd 0301 abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) — 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) — 01 means the year ...

  • Page 511

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 512

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire and loading information placard this placard tells you important information about the: ...

  • Page 513

    3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to th...

  • Page 514

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 515

    5 starting and operating 513.

  • Page 516

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 517

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns t...

  • Page 518

    Tire inflation pressures at least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire we...

  • Page 519

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits ...

  • Page 520

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat, • the damage is only on the tread section of your tire (sidewall damage is not repairable) and • the puncture is no greater than ¼⬙ (6 mm) consult an authoriz...

  • Page 521

    Snow tires some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a mountain/snowflake symbol on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of fou...

  • Page 522

    Compact spare tire – if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on the tire and loading information placard located on the driver’s side door opening or on the sidewall ...

  • Page 523

    Your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Limited-use spare – if equipped the limited-use spare tire is for temporary emergency use only. This tire is identified by a label located on the limited-use spare whe...

  • Page 524

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping when you are stuck. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warnin...

  • Page 525

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to replacement tires in this section for further informa- tion. Life of tir...

  • Page 526

    Information placard or the vehicle certification label for the size designation of your tire. The load index and speed symbol for your tire will be found on the original equipment tire sidewall. See the tire sizing chart ex- ample found in the tire safety information section of this manual for more ...

  • Page 527

    Warning! (continued) • failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire chains (tract...

  • Page 528

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 529

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation a...

  • Page 530

    Tire pressure monitor system (tpms) the tpms will warn the driver of a low tire pressure based on the cold inflation tire placard pressure require- ments found on the tire placard label located on the driver’s-side b-pillar. The tire pressure will vary with temperature by about 1 psi (7 kpa) for eve...

  • Page 531

    For example, your vehicle may have a recommended cold (parked for more than three hours) tire placard pressure of 35 psi (241 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressure is 30 psi (207 kpa), a temperature drop to 20°f (-7°c) will decrease the tire pressure to appro...

  • Page 532

    Note: • the tpms is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat ...

  • Page 533

    Tire pressure monitoring low tire pressure warnings the “tire pressure monitoring telltale light” will illuminate in the instrument cluster, a “low tire pressure” message will display in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pres...

  • Page 534

    3. Accumulation of excessive snow and/or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpms sensors. Vehicles with compact spare 1. The compact spare tire (if equipped) does not have a tpms sensor. Therefore the tpms will not mo...

  • Page 535

    Premium system – if equipped the tpms uses wireless technology with wheel rim- mounted electronic sensors to monitor tire pressure lev- els. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the receiver module. Note: it is particularly important to regularly...

  • Page 536

    Note: the vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this infor- mation. Service tpm system message the “tire pressure monitoring telltale light” will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will...

  • Page 537

    Message is then followed by a graphic display with pressure values still shown. This indicates that the pres- sure values are still being received from the tpm sensors but they may not be in the correct vehicle position. The system still needs to be serviced as long as the “service tpm system” messa...

  • Page 538

    5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the tpms will update automatically. In addition, the “tire pressure monitoring telltale light” will turn off and the graphic in the evic will display a new pressure value instead of d...

  • Page 539

    Fuel requirements 3.6l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high-quality unleaded “regular” gaso- line having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide a...

  • Page 540

    Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” reformulated gasolines contain oxygenates and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of ref...

  • Page 541

    E-85 usage in non-flex fuel vehicles non-ffv vehicles are compatible with gasoline contain- ing 10% ethanol (e10). Gasoline with higher ethanol content may void the new vehicle limited warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these sy...

  • Page 542

    Therefore, you should ask your gasoline retailer whether the gasoline contains mmt. Mmt is prohibited in federal and california reformulated gasoline. Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or ...

  • Page 543

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the respon...

  • Page 544

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Flexible fuel — if equipped e-85 general informa...

  • Page 545

    Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap)...

  • Page 546

    Fuel requirements if your vehicle is e-85 compatible, it will operate on unleaded gasoline with an octane rating of 87, or e-85 fuel, or any mixture of these two fuels. For best results, a refueling pattern that avoids alternat- ing between e-85 and unleaded gasoline is recom- mended. When you do sw...

  • Page 547

    Selection of engine oil for flexible fuel vehicles (e-85) and gasoline vehicles ffv vehicles operated on e-85 require specially formu- lated engine oils. These special requirements are included in mopar® engine oils, and in equivalent oils meeting chrysler specification ms-6395. The manufacturer onl...

  • Page 548

    Replacement parts many components in your flexible fuel vehicle (ffv) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol com- patible parts. Caution! Replacing fuel system components with non-ethanol compatible components can damage your veh...

  • Page 549

    Note: the driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door. Caution! • damage to the fuel system or emissions control system could result from using an improper fuel tank filler tu...

  • Page 550

    • tighten the fuel filler cap until you hear a “clicking” sound. This is an indication that the fuel filler cap is properly tightened. • if the gas cap is not tightened properly, the mil may come on. Be sure the gas cap is tightened every time the vehicle is refueled. Loose fuel filler cap message i...

  • Page 551

    The label contains the following information: • name of manufacturer • month and year of manufacture • gross vehicle weight rating (gvwr) • gross axle weight rating (gawr) front • gross axle weight rating (gawr) rear • vehicle identification number (vin) • type of vehicle • month day and hour of man...

  • Page 552

    Rim size this is the rim size that is appropriate for the tire size listed. Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids,...

  • Page 553

    Loading to load your vehicle properly, first figure out its empty weight, axle-by-axle and side-by-side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely before driving. If weighing the loaded vehicle shows that you have exceed...

  • Page 554

    Exceed the gvwr. Refer to “vehicle loading/vehicle certification label” in “starting and operating” for further information. Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer ...

  • Page 555

    Trailer sway control the trailer sway control can be a mechanical telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable fric- tion associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveli...

  • Page 556

    Warning! • an improperly adjusted weight-distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • weight-distributing hitch systems may not be com- patible with surge brake couplers. Consult with an authorized hitch and trailer manufacturer or...

  • Page 557

    With weight-distributing hitch (correct) improper adjustment of weight-distributing hitch (incorrect) 5 starting and operating 555.

  • Page 558

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 559

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission gcwr (gross combined weight rating) frontal area max. Gtw (gross trailer weight) max. Tongue weight 3.6l/automatic 8,750 lbs...

  • Page 560

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further information. Trailer and ton...

  • Page 561

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the maximum combine...

  • Page 562

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 563

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Trailer tongue weight rating for the trailer hitch utilized. Towing requirements – tires • do not attempt to tow a trailer ...

  • Page 564

    • an electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • trailer brakes are recommended for trailers over...

  • Page 565

    Towing requirements – trailer lights and wiring whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The trailer tow package may include a four- and seven- pin wiring harness. Use a factory approved trailer har- nes...

  • Page 566

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic transmission the drive gear can be selected when towing. However, if frequent shifting occurs while in drive, use the electronic range select (ers) s...

  • Page 567

    Or frequent trailer towing.” refer to the “maintenance schedule” for the proper maintenance intervals. Electronic speed control – if equipped • do not use in hilly terrain or with heavy loads. • when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage unti...

  • Page 568

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground all models flat tow none not allowed dolly tow front ok rear not allowed on trailer all ok 566 starting and operating.

  • Page 569

    Recreational towing – all models recreational towing is allowed only if the front wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure: 1. Properly secure the dolly to the tow vehicle, following the dolly manufacturer’s...

  • Page 571: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .570 䡵 if your engine overheats . . . . . . . . . . . .570 䡵 jacking and tire changing . . . . . . . . . .571 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . .572 ▫ spare tire removal. . . . . . . . . . . ...

  • Page 572

    Hazard warning flashers the hazard warning flasher switch is located in the lower center area of the instrument panel. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 573

    Caution! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “h”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h”, turn the engine off immedi...

  • Page 574

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack location the jack, jack handle and winch handle...

  • Page 575

    Spare tire removal the spare tire is stowed inside a protective cover located under the center of the vehicle between the front doors by means of a cable winch mechanism. The “spare tire drive” nut is located on the floor, under a plastic cap at the front of the floor console or under front super co...

  • Page 576

    To access spare tire winch drive nut to access the spare tire winch drive nut and lower the spare tire, you will need to refer to one of the following center console configurations. Super console for vehicles equipped with the super console, the spare tire winch assembly drive nut is located beneath...

  • Page 577

    2. Open the front drawer to expose the storage compart- ment. 3. Remove the liner from the console’s storage compart- ment to access the spare tire winch drive nut. Premium/base/cargo center console pull the winch cover assembly plug (if equipped) to access the winch drive nut. Drive nut access winc...

  • Page 578

    Spare tire tools the tool pouch contains three pieces and can be as- sembled into a spare tire hook; to remove the compact spare tire/cover assembly from under the vehicle, or a winch t-handle; to raise/lower the compact spare tire/ cover assembly. Assembled t-handle a — spare tire hook/t-handle b —...

  • Page 579

    Spare tire removal instructions the spare tire is located under the vehicle beneath the center console area. 1. Assemble the spare tire tools into a t-handle and place the square end over the spare tire winch drive nut. Assembling the spare tire hook a — spare tire hook/t-handle b — extension 1 c — ...

  • Page 580

    2. Rotate the nut to the left until the winch mechanism stops turning freely. This will allow enough slack in the cable to allow you to pull the spare tire out from underneath the vehicle. Caution! The winch mechanism is designed for use with the winch t-handle only. Use of an air wrench or other po...

  • Page 581

    4. Stand the tire/cover assembly upright and remove the wheel spacer by squeezing the winch retaining tabs together. Push the retainer through the spare tire to release it from the wheel. Preparations for jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. Warning! Do ...

  • Page 582

    6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jacking instructions warning! Carefully follow these t...

  • Page 583

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 584

    2. There are two jack engagement locations on each side of the vehicle body. These locations are on the sill flange of the vehicle body. Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated. Rear jack locations are between a pair of down-facing tabs on the ...

  • Page 585

    Front jack location is on the sill flange of the vehicle body and is located 6 in (150 mm) from door edge. Note: in some situations the jack may need to be placed on its side in order to be pushed under the vehicle. Return the jack to its correct orientation once it is under the vehicle. Warning! Be...

  • Page 586

    4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. Warning! Raising the vehicle higher than neces...

  • Page 587

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Note: do not install the wheel cover on the compact spare. 7. Lower the vehicle by turning the jack sc...

  • Page 588

    9. Lower the jack to its fully-closed position. Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately...

  • Page 589

    Securing the spare tire 1. Assemble the winch handle extensions to form a t-handle and fit the winch t-handle over the drive nut. Rotate the nut to the left until the winch mecha- nism stops turning freely. This will allow enough slack in the cable to allow you to pull the wheel spacer out from unde...

  • Page 590

    Caution! The compact spare tire/cover assembly must be used when the compact spare tire is stored. Failure to use this cover could drastically reduce the life of the compact spare tire. Warning! Verify that both retainer tabs of the wheel spacer have been properly extended through the center of the ...

  • Page 591

    Road tire installation vehicles equipped with wheel covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two lug nuts on the mounting studs which are on each side of the valve stem. Install the lug nuts with the cone shaped end of...

  • Page 592

    3. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Ligh...

  • Page 593

    Vehicles without wheel covers 1. Mount the road tire on the axle. 2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicl...

  • Page 594

    Jump-starting if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. Note:...

  • Page 595

    Preparations for jump-start the battery in your vehicle is located on the left side of the engine compartment. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any m...

  • Page 596

    3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-start...

  • Page 597

    Warning! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then st...

  • Page 598

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse while gently pressing the accelerator. Use t...

  • Page 599

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 600

    4. Press and maintain firm pressure on the brake pedal. 5. Insert the screwdriver or similar tool into the access hole, and push and hold the override release lever forward. 6. Move the shift lever to the neutral position. 7. The vehicle may then be started in neutral. 8. Reinstall the shift lever o...

  • Page 601

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. Towing condition wheels off the ground all models flat tow none if transmission is operable: • transmission in neutral • 25 mph (40 km/h) max speed • 15 miles (24 km) max dis...

  • Page 602

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 603

    The manufacturer recommends towing your vehicle with all four wheels off the ground using a flatbed. If flatbed equipment is not available, and the transmission is operable, the vehicle may be flat towed (with all four wheels on the ground) under the following conditions: • the transmission must be ...

  • Page 605: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . .605 䡵 onboard diagnostic system — obd ii . . .606 ▫ loose fuel filler cap message . . . . . . . . . . . .607 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . .607 䡵 replacement parts . . . . . . ....

  • Page 606

    ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .633 ▫ cleaning the instrument panel cupholders . . .640 䡵 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .640 ▫ totally integrated power module . . . . . . . . . .640 䡵 vehicle stora...

  • Page 607

    Engine compartment — 3.6l 1 — air filter 6 — engine coolant reservoir 2 — power steering fluid reservoir 7 — engine oil dipstick 3 — brake fluid reservoir 8 — engine oil fill 4 — battery 9 — coolant pressure cap 5 — totally integrated power module (fuses) 10 — washer fluid reservoir 7 maintaining yo...

  • Page 608

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 609

    Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will display in the odometer or a “check gascap” message will be displayed in the electronic vehicle information center (evic). Refer to “...

  • Page 610

    Your vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. To check if your vehicle’s obd ii system is ready, you must do the following: 1. Cycle the ignition switch to the on position, but do not crank or start the engine. 2. If you crank or start th...

  • Page 611

    Regardless of whether your vehicle’s obd ii system is ready or not, if the mil is illuminated during normal vehicle operation you should have your vehicle serviced before going to the i/m station. The i/m station can fail your vehicle because the mil is on with the engine running. Replacement parts ...

  • Page 612

    Maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the futu...

  • Page 613

    Check the engine oil level is about five minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the min and max...

  • Page 614

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american petroleum institute (api). The manufacturer only recommends api certified engine oils. Caution! Do not use chemical flushes in your engine oil as the chemicals can da...

  • Page 615

    Materials added to engine oil the manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental addi- tives. Disposing of used engine oil and oil fil...

  • Page 616

    Engine air cleaner filter refer to the “maintenance schedule” for the proper maintenance intervals. Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unles...

  • Page 617

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 618

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 619

    Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water. R...

  • Page 620

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 621

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized dealer or othe...

  • Page 622

    5. Remove the a/c air filter by pulling it straight out of the housing. 6. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. Caution! The a/c air filter is identified with an arrow...

  • Page 623

    Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubri- cated periodically with a lithium based grease, such as mopar® spray white lube to assure quiet, easy opera-...

  • Page 624

    Adding washer fluid the fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few se...

  • Page 625

    Cooling system warning! • when working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at anytime the ignition switch is in the on position. • you or others can be badly burned by hot engine...

  • Page 626

    Cooling system – drain, flush, and refill if the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with oat coolant (antifreeze) (conforming to ms- 12106). Refer to the “maintenance schedule” for the proper maintenance intervals. Selection o...

  • Page 627

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 628

    • mix a minimum solution of 50% oat engine coolant that meets the requirements of chrysler material stan- dard ms-12106 and distilled water. Use higher concen- trations (not to exceed 70%) if temperatures below −34° f (−37° c) are anticipated. • use only high purity water such as distilled or deion-...

  • Page 629

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 630

    The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing cool- ant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle ne...

  • Page 631

    • if frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested for leaks. • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms- 12106) and distilled water for proper corrosion protec- tion of your engin...

  • Page 632

    Master cylinder – brake fluid level check the fluid level in the master cylinder should be checked when performing underhood services, or immediately if the “brake system warning light” indicates system failure. Clean the top of the master cylinder area before removing the cap. Add fluid to bring th...

  • Page 633

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 634

    Important to maintain the transmission fluid at the correct level using the recommended fluid. No chemical flushes should be used in any transmission; only the approved lubricant should be used. Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deteriora...

  • Page 635

    Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating conditions. Routine fluid level checks are not required, therefore the transmission filler tube is capped and no dipstick is provided. Your authorized dealer can check your trans- missio...

  • Page 636

    Hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion i...

  • Page 637

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 638

    Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use mopar® wheel cleaner or equivalent or select a non- abrasive, non-acid...

  • Page 639

    • for tough stains, apply mopar® total clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar® multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap resid...

  • Page 640

    Liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather condi- tioner is not required to maintain the original condition. Warning! Do not use volatile solvents for cleaning purposes. Many ar...

  • Page 641

    When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be...

  • Page 642

    Cleaning the instrument panel cupholders removal pull the flexible liner from the cupholder drawer starting at one edge to ease removal. Cleaning the liner is top shelf dishwasher safe, or you may follow the cleaning procedure below. Soak the liner in a mixture of medium hot tap water and one teaspo...

  • Page 643

    Caution! • when installing the totally integrated power mod- ule cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power module, and possibly result in a electrical system failure. • when replacing a blown...

  • Page 644

    Cavity car- tridge fuse mini- fuse description j1 40 amp green — power folding seat j2 30 amp pink — power liftgate module j3 30 amp pink — rear door module j4 25 amp natural — driver door node j5 25 amp natural — passenger door node j6 40 amp green — antilock brakes pump/stability control system ca...

  • Page 645

    Cavity car- tridge fuse mini- fuse description j11 30 amp pink — power sliding door module/anti–theft module – if equipped j12 30 amp pink hvac rear blower, radiator fan motor j13 60 amp yellow — ignition off draw (iod) – main j14 40 amp green — rear window de- fogger j15 40 amp green — front blower...

  • Page 646

    Cavity car- tridge fuse mini- fuse description m2 — 20 amp yellow front fog lamps m3 — 20 amp yellow front/rear axle locker, vacuum pump motor m4 — 10 amp red trailer tow m5 — 25 amp natural inverter m6 — 20 amp yellow power outlet #1 (acc), rain sensor, cigar lighter (in- strument panel or with con...

  • Page 647

    Cavity car- tridge fuse mini- fuse description m10 — 15 amp blue ignition off draw — video system, satellite radio, dvd, hands-free module, universal garage door opener, vanity lamp, streaming video module – if equipped m11 — 10 amp red climate control system m12 — 30 amp green amplifier/radio cavit...

  • Page 648

    Cavity car- tridge fuse mini- fuse description m16 — 10 amp red airbag module/ occupant classifi- cation module m17 — 15 amp blue left tail/license/ park lamp, run- ning lamps m18 — 15 amp blue right tail/park/ run lamp m19 — 25 amp natural powertrain cavity car- tridge fuse mini- fuse description m...

  • Page 649

    Cavity car- tridge fuse mini- fuse description m24 — 25 amp natural rear wiper m25 — 20 amp yellow fuel pump, diesel lift pump – if equipped m26 — 10 amp red power mirror switch, driver win- dow switch m27 — 10 amp red wireless control module, keyless entry module m28 — 10 amp red powertrain, trans-...

  • Page 650

    Cavity car- tridge fuse mini- fuse description m34 — 10 amp red park assist, heater climate control module, headlamp wash, compass, rear camera, door lamps, flashlight, relay diesel cabin heater, rad fan diesel – if equipped m35 — 10 amp red heated mirrors cavity car- tridge fuse mini- fuse descript...

  • Page 651

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take steps to protect your battery. You may do the following: • remove the 60 amp cartridge in the totally integrated power module (tipm) labeled ignition-off draw (iod). • or, disconnect the negative cabl...

  • Page 652

    Bulb number instrument cluster lamps pc74 liftgate lamp(s) 578 overhead console read- ing lamps pc579 removable console lamp – if equipped 194 visor vanity lamps 6501966 note: for lighted switches, see your authorized dealer for replacement instructions. Exterior bulbs bulb number headlamp h11 fog l...

  • Page 653

    Bulb replacement headlamps 1. Raise the hood to access the rear of the headlamp housing. 2. Slide the red lock tab rearward on the connector, then depress the tab and remove the connector from the bulb. 3. Twist the headlamp bulb and pull the bulb from the headlamp housing. 4. Install the new headla...

  • Page 654

    Fog lamps note: access to the fog lamp bulb is from the rear of the fascia. On the left rear side of the fascia, remove the push pin and lower the hinged access door on the air dam. 1. From behind the bumper fascia, or the access panel on the air dam, squeeze the two tabs on the side of the bulb soc...

  • Page 655

    Rear tail, stop, turn signal, side marker and backup lamps 1. Raise the liftgate. 2. Remove the tail lamp assembly by removing the two screws from the inboard side. Use a fiber stick or similar tool to gently pry the light on the outboard side to disengage the two ball studs. Note: • if a screwdrive...

  • Page 656

    3. Twist the socket and remove from the lamp assembly. 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the lamp assembly. Center high-mounted stop lamp (chmsl) the chmsl uses led lamps that are not serviceable separately. The chmsl must be repla...

  • Page 657

    Fluid capacities u.S. Metric fuel (approximate) 20 gallons 76 liters engine oil with filter 3.6l engine (sae 5w-20, api certi- fied) 6 quarts 5.6 liters cooling system * 3.6l engine (mopar® antifreeze/ engine coolant 10 year/150,000 mile formula or equivalent) 13.4 quarts 12.6 liters * includes heat...

  • Page 658

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) meeting the requirements of chrysler ma- terial standard ms-12106. Engine oil we recomm...

  • Page 659

    Chassis component fluid, lubricant, or genuine part automatic transmission we recommend you only use mopar® atf+4® automatic transmission fluid. Failure to use atf+4® fluid may affect the function or performance of your transmission. Brake master cylinder we recommend you use mopar® dot 3 and sae j1...

  • Page 661: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .660 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .661 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 662

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 663

    Required maintenance intervals . Refer to the maintenance schedules on the following page for the required maintenance intervals. At every oil change interval as indicated by oil change indicator system: • change oil and filter. • rotate the tires. Rotate at the first sign of irregu- lar wear, even ...

  • Page 664

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 665

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 666

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 667

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 669: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . .669 ▫ prepare for the appointment. . . . . . . . . . . . .669 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .669 ▫ be reasonable with requests . . . . ....

  • Page 670

    䡵 publication order forms . . . . . . . . . . . .674 䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .675 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .675 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .675 ▫ temperature gr...

  • Page 671

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 672

    Warranty service must be done by an authorized dealer. We strongly recommend that you take the vehicle to an authorized dealer. They know your vehicle the best, and are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trai...

  • Page 673

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 674

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 675

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 676

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 677

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 678

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 679: Index

    Index 10

  • Page 680

    Adding engine coolant (antifreeze) . . . . . . . . . . . .625 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .546 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .622 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .540 adjustable pedals . . . ....

  • Page 681

    Automatic transmission . . . . . . . . . . . . . . . . . . . .468 adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .633 fluid and filter changes . . . . . . . . . . . . . . . . . .633 fluid change . . . . . . . . . . . . . . . . . . . . . . . . . .633 fluid level check . . . . . . . . ...

  • Page 682

    Carbon monoxide warning . . . . . . . . . . . . . . . . . .118 cargo area features . . . . . . . . . . . . . . . . . . . . . . .294 cargo compartment . . . . . . . . . . . . . . . . . . . . . . .294 luggage carrier . . . . . . . . . . . . . . . . . . . . . . . .298 cargo (vehicle loading) . . . . . ...

  • Page 683

    Coolant pressure cap (radiator cap) . . . . . . . . . . .626 cooling system. . . . . . . . . . . . . . . . . . . . . . . . . . .623 adding coolant (antifreeze) . . . . . . . . . . . . . . .625 coolant capacity . . . . . . . . . . . . . . . . . . . . . . .655 coolant level . . . . . . . . . . . . . ....

  • Page 684

    E-85 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .542 economy (fuel) mode . . . . . . . . . . . . . . . . . . . . . .471 electrical power outlets. . . . . . . . . . . . . . . . . . . . .269 electric remote mirrors . . . . . . . . . . . . . . . . . . . . .133 electronic brake con...

  • Page 685

    Enhanced accident response feature . . . . . . . . . . . .86 entry system, illuminated . . . . . . . . . . . . . . . . . . . .20 ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .538 event data recorder . . . . . . . . . . . . . . . . . . . . . . . .90 exhaust gas caution. . . ....

  • Page 686

    Power steering . . . . . . . . . . . . . . . . . . . . . . . . .486 fluids, lubricants and genuine parts . . . . . . . . . . .656 fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 fog light service . . . . . . . . . . . . . . . . . . . . . . . . .652 fold in floor (stow ⬘n go...

  • Page 687

    Gasoline, reformulated . . . . . . . . . . . . . . . . . . . . .538 gauges coolant temperature . . . . . . . . . . . . . . . . . . . . .326 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323 speedometer . . . . . . . . . . . . . . . . . . . . . . . . . .323 tachometer . . . . ...

  • Page 688

    Hook, coat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .285 ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ignition key removal . . . . . . . . . . . . . . . . . . . . . . .14 illumin...

  • Page 689

    Life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .523 liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 light bulbs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12...

  • Page 690

    Security alarm (theft alarm) . . . . . . . . . . . . . . .324 service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .649 service engine soon (malfunction indicator) . . . .321 side marker . . . . . . . . . . . . . . . . . . . . . . . . . . .653 theft alarm (security alarm) . . . . . . ...

  • Page 691

    Mode fuel saver . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 modifications/alterations, vehicle . . . . . . . . . . . . . . .8 monitor, tire pressure system . . . . . . . . . . . . . . . .528 mopar parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .609 mtbe/etbe . . . . . ....

  • Page 692

    Paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .633 panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 parking brake. . . . . . . . . . . . . . . . . . . . . . . . . . . .487 park sense system, rear . . . . . . . . . . . . . . . . . . . .239 pedals, adjus...

  • Page 693

    Reclining front seats . . . . . . . . . . . . . . . . . . . . . . .191 recorder, event data . . . . . . . . . . . . . . . . . . . . . . .90 recreational towing . . . . . . . . . . . . . . . . . . . . . . .566 reformulated gasoline . . . . . . . . . . . . . . . . . . . . .538 refrigerant . . . . . . ...

  • Page 694

    Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . .68 rear seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182 adjustment ...

  • Page 695

    Steering power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .485 tilt column . . . . . . . . . . . . . . . . . . . . . . . . . . .232 wheel, heated . . . . . . . . . . . . . . . . . . . . . . . . .233 wheel, tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . .232 steering whee...

  • Page 696

    Life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . .523 load capacity . . . . . . . . . . . . . . . . . . . . . . . . .510 pressure monitor system (tpms) . . . . . . . . . . . .528 pressure warning light . . . . . . . . . . . . . . . . . . .319 quality grading . . . . . . . . . . . . ...

  • Page 697

    Trailer weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .557 transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . .631 automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .468 fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .631 transmitter ...

  • Page 698

    Water driving through . . . . . . . . . . . . . . . . . . . . . . . .483 wind buffeting. . . . . . . . . . . . . . . . . . . . . . . . . . . .44 window fogging . . . . . . . . . . . . . . . . . . . . . . . . .459 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 power . . . ....

  • Page 699

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 700

    300