1. DL manuals
  2. RAM
  3. Automobile
  4. 2015 ProMaster City
  5. Owner's Manual

RAM 2015 ProMaster City Owner's Manual

Summary of 2015 ProMaster City

  • Page 1

    P r o m a s t e r c i t y o w n e r ’ s m a n u a l 2 0 1 5 2015 promaster city 15vm-126-ac third edition printed in u.S.A. Fca us llc.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .4 䡵 warnings and cautions . . . . . . . . . . . . . .6 䡵 van conversions/campers . . . . . . . . . . . .6 䡵 vehicle identification number . . . . . . . .6 䡵 vehic...

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engine...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importan...

  • Page 9

    Frame and underbody as well as the automobile infor- mation disclosure label affixed to a window on your vehicle, the vehicle registration and title. Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seri...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 sentry ke...

  • Page 12

    ▫ unlock the doors from the outside . . . . . . . .23 ▫ unlocking the rear cargo area from inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 ▫ sliding side doors. . . . . . . . . . . . . . . . . . . . . .23 ▫ child lock system — if equipped . . . . . . . . . .24 ▫ auto u...

  • Page 13

    䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . .86 ▫ transporting passengers. . . . . . . . . . . . . . . . . .86 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .87 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 14

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key, simply push the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized ...

  • Page 15

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park and re- move the key fob from the vehicle. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children t...

  • Page 16

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unatt...

  • Page 17

    Note: a key which has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. If the vehicle security light is on after the key is turned to the on/run position, it indicates that there is a problem with the electronics. Cau...

  • Page 18

    General information the sentry key® system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference ...

  • Page 19

    To arm the system to arm the system, the vehicle security alarm will set when you use the remote keyless entry (rke) transmit- ter to lock the doors. If a door or the hood is not properly shut, the alarm system will exclude the related door from protection. To disarm the system use the rke transmitt...

  • Page 20

    To unlock the doors cargo vehicle push and release the unlock button on rke transmit- ter to unlock the front two doors depending. Push and release the cargo unlock button on rke transmitter to unlock the cargo area (side lateral sliding doors and rear doors). The turn signal lights will flash to ac...

  • Page 21

    To lock the doors push and release the lock button on the rke transmit- ter to lock all doors. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Programming additional transmitters refer to “sentry key” in “things to know before start- ing” for further information....

  • Page 22

    General information this device complies with part 15 of the fcc rules and rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 23

    Door locks the door locks can be locked or unlocked from inside the vehicle by using the door handle. • to lock the doors, push down on the door handle. • to unlock the doors, pull up on the door handle. Power door locks 2 things to know before starting your vehicle 21.

  • Page 24

    Locking the doors from the outside locking with an rke transmitter push and release the lock button on the rke transmit- ter to lock all doors. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Locking with the rke key blade 1 – mechanical key release button 2 – dr...

  • Page 25

    Push the mechanical key release button (item #1 shown above) to expose the rke key blade, insert the key blade into the doors exterior lock cylinder and turn the key clockwise to lock the front door. Unlock the doors from the outside unlocking with an rke transmitter on the passenger vehicle, push a...

  • Page 26

    The vehicle until it locks into place and cannot go any further. The turn signal lights will flash to acknowledge the unlock signal. Unlocking with the rke key blade push the mechanical key release button to expose the rke key blade, insert the key blade into the driver exterior door lock cylinder a...

  • Page 27

    To engage or disengage the child-protection door lock system 1. Open the rear door. 2. Insert the tip of the emergency key into the lock and rotate to the lock or unlock position. 3. Repeat steps 1 and 2 for the opposite rear door. The device remains engaged even if the doors are un- locked remotely...

  • Page 28

    Windows power windows — if equipped the control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control. Note: the key off power delay feature will al...

  • Page 29

    Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pe...

  • Page 30

    Warning! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Power windows system initialization the power windows may be reset if any of the following occurs: • on the front doors • fuse or battery are disconnected • on th...

  • Page 31

    Sliding side door on cargo versions, the sliding side door is fitted with a spring-loaded latch that stops the door from opening any further. To lock it, simply push the door as far as it will go; to unlock it, pull forward firmly. Opening and closing from outside the vehicle opening/unlocking with ...

  • Page 32

    Opening and closing from the inside opening: pull the interior door handle switch to unlock the door, then pull the handle and slide the door towards the rear of the vehicle until it can go no further. Closing: pull the interior door handle switch to release the door and then push it towards the fro...

  • Page 33

    The device is released and thus the doors can be opened as follows: if the power is restored: • by remote control. • opening a front door by inserting the key into the key pawl. If the power is not restored: • opening the driver side door by key pawl and the other doors (passenger’s side and sliding...

  • Page 34

    Opening/closing the first swing door from the outside to open the door, turn the key in the lock or push the cargo lock button on the remote control and then pull the exterior handle to the left. To close the door, turn the key in the lock or push the lock button on the remote keyless (rke) transmit...

  • Page 35

    2. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (refer to “child restraints”) 3. Children that are not big enough to wear the vehicle seat belt properly (refer...

  • Page 36

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 37

    If the driver or outboard front seat passenger seat belt is unbuckled once the vehicle speed is over 12.5 mph (20 km/h) or when travelling at a speed from 6 to 12.5 mph (10 to 20 km/h) for few seconds, the beltalert warning sequence begins by blinking the seat belt re- minder light and sounding an i...

  • Page 38

    Will lock and reduce your risk of striking the inside of the vehicle or being thrown out of the vehicle. Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t ...

  • Page 39

    Warning! (continued) • two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. • a lap belt worn too high c...

  • Page 40

    Warning! (continued) your strongest bones will take the force in a colli- sion. • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to b...

  • Page 41

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 42

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automaticall...

  • Page 43

    Adjustable upper shoulder belt anchorage — cargo van in the driver and front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck. Push or squeeze the anchorage button to release the anchorage, and move it up or down to the po...

  • Page 44

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 45

    Seat belt pretensioner the front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision. Pretensione...

  • Page 46

    • alr = switchable automatic locking retractor if the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, yo...

  • Page 47

    Sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occupant’s mid-section. Slide the latch plate into the buckle until you hear a ⬙click.⬙ in automatic locking mode, the...

  • Page 48

    Mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the seat belt assembly must be replaced if the switchable automatic locking retractor (alr) fea- ture or any other seat belt function is not working properly when checked according to the proce- dures in the service manual....

  • Page 49

    • seat belt pretenioners • seat belt buckle switch advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s advanced front air bag is mounted in the center of the steering wheel. The pass...

  • Page 50

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 51

    Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bags to inflate. • do not put anything on or around the air bag covers or attempt to op...

  • Page 52

    Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away f...

  • Page 53

    Provides enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and advanced front air bags. Supplemental side air bags your vehicle is equipped with two types of supplemental side air bags: 1. Supplemental seat-mounted side air bags (sabs): located in th...

  • Page 54

    Deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure you if you are not seated properly, or if items are positioned in the area where the sab inflates. Children are at an even greater risk o...

  • Page 55

    The sabic deploys downward, covering the side win- dows. An inflating sabic pushes the outside edge of the headliner out of the way and covers the window. The sabics inflate with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the sa...

  • Page 56

    The side impact sensors aid the orc in determining the appropriate response to impact events. The system is calibrated to deploy the side air bags on the impact side of the vehicle during impacts that require side air bag occupant protection. In side impacts, the side air bags deploy independently; ...

  • Page 57

    Warning! • side air bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • being too close to the side air bags during deploy- ment could cause you to be severely injured or killed. • relying on the side air bags alone could lead to more severe in...

  • Page 58

    • as the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the are...

  • Page 59

    Enhanced accident response system in the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the orc will determine whether to have the enhanced accident response sys- tem perform the following functions: • cut off fuel...

  • Page 60

    The orc contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. The orc turns on the air bag warning light in the instrument panel for approximately four to eight seconds for a self-check when the ignition swi...

  • Page 61

    Warning! Ignoring the air bag warning light in your instru- ment panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first placed in the on position, and stays on after you start the vehicle, or if it comes on...

  • Page 62

    Warning! (continued) upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or add aftermarket side steps or running boards. • it is dangerous to try to repair any part of the air bag system yourself. Be sure to tell anyone who works on your vehicle that it...

  • Page 63

    • how far (if at all) the driver was depressing the accelerator and/or brake pedal • how fast the vehicle was traveling these data can help provide a better understanding of the circumstances in which crashes and injuries occur. Note: edr data are recorded by your vehicle only if a non-trivial crash...

  • Page 64

    Warning! In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in you...

  • Page 65

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 66

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 67

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 68

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 69

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 70

    Lower anchors and tethers for children (latch) restraint system (passenger vehicle) your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equip...

  • Page 71

    Latch positions for installing child restraints in this vehicle lower anchor / top tether locations (passenger vehicle) • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to know before starting your vehicle 69.

  • Page 72

    Child restraint latch positions what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5...

  • Page 73

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 74

    Locating latch anchorages (passenger vehicle) the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will...

  • Page 75

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing child restraints...

  • Page 76

    Always follow the directions of the child restraint manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. To install a latch-compatible child restraint: if the selected seating position has a switchable auto- matic locking retractor (...

  • Page 77

    6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. How to stow an unused alr seat belt: when using the latch attaching system to install a child restraint, stow all alr se...

  • Page 78

    Installing child restraints using the vehicle seat belt (passenger vehicle) the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not ...

  • Page 79

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restrai...

  • Page 80

    Installing a child restraint with a switchable automatic locking retractor (alr): 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and ...

  • Page 81

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 82

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 83

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 84

    Not necessary to use a locking clip. The alr retractor can be “switched” into a locked mode by pulling all of the webbing out of the retractor and then letting the webbing retract back into the retractor. If it is locked, the alr will make a clicking noise while the webbing is pulled back into the r...

  • Page 85

    Installing a child restraint with a switchable automatic locking retractor (alr): commercial 1. Place the child seat in the center of the seating position. 2. Pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child restraint. Do not twist the belt webbin...

  • Page 86

    Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. Installing child restraints using the top tether anchorage (commercial vehicle) this vehicle is equipped with a tether strap anchorage located behind the front passenger seatback, near the flo...

  • Page 87

    Transporting pets air bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by sea...

  • Page 88

    Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave c...

  • Page 89

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 90

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 91

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 92

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 93: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 ▫ inside day/night mirror — if equipped . . . . .94 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . .94 ▫ manual folding door mirrors . . . . . . . . . . . . .95 ▫ ...

  • Page 94

    ▫ parking lights . . . . . . . . . . . . . . . . . . . . . . .112 ▫ turn signals . . . . . . . . . . . . . . . . . . . . . . . . .112 ▫ lane change assist . . . . . . . . . . . . . . . . . . . .112 ▫ follow me home/headlight delay . . . . . . . . .112 ▫ front fog lights — if equipped . . . . . . . ....

  • Page 95

    䡵 parkview® rear back up camera — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .129 䡵 power outlets . . . . . . . . . . . . . . . . . . . . .131 䡵 cigar lighter and ash receiver — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .134 䡵 cupholder . . . . . . . . . . ...

  • Page 96

    Mirrors inside day/night mirror — if equipped a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the vi...

  • Page 97

    Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or...

  • Page 98

    Manual outside mirror adjustment — if equipped from the inside of the vehicle, use the control lever to adjust the mirror. Power outside mirrors — if equipped the power mirror controls are located on the mirror flag trim above the driver’s door trim panel. To adjust a mirror, turn the control knob t...

  • Page 99

    Sun visors the driver and passenger sun visors are located on the headliner, near the front windshield. The sun visor can be rotated downward or up against the door glass. Your vehicle may be equipped with courtesy mirror located on the passenger sun visor. Power mirror controls 1 — driver mirror se...

  • Page 100

    “slide-on-rod” of sun visor to use the “slide-on-rod” feature of the sun visor, rotate the sun visor downward and swing the sun visor so it is parallel to the side window, grabbing the sun visor with your left hand pull rearwards until the sun visor is in the desired position. Seats seats are a part...

  • Page 101

    Manual seat adjustments the front driver and passenger seats can be adjusted forward and rearward and if equipped may be reclined and the height and lumbar can be adjusted. Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which c...

  • Page 102

    Forward and rearward adjustment the adjusting bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rear- ward. Release the bar once the seat is in the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the se...

  • Page 103

    Folding rear seat — if equipped to provide additional storage area, each rear seat can be folded flat to allow for extended cargo space. 1. Locate the release lever (upper outboard side of seat), and lift it upward until the seatback releases. 2. Slowly fold down the seatback. 3. Pull forward on the...

  • Page 104

    4. Reverse order for original setting. Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the lower outboard side of the seat. Push the button onc...

  • Page 105

    Note: • this features is allowed only with ignition key at mar (acc/on/run) position. • once a heat setting is selected, heat will be felt within two to five minutes. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, me...

  • Page 106

    Warning! (continued) never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision. Front head restraints to raise the head restraint, push the adjustment button, located on ...

  • Page 107

    Warning! • a loose head restraint thrown forward in a colli- sion or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow removed head restraints in a location outside the occupant compartment. • all the head restraints must be reinstalled in the vehicle to...

  • Page 108

    The center head restraint is adjustable and removable. To raise the head restraint, push and hold the adjustment button, located on the base of the head restraint and pull upward on the head restraint. To lower the head restraint, push and hold the adjustment button, and push down- ward on the head ...

  • Page 109

    Warning! All the head restraints must be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat. To open and close the hood to open the hood, two latches must be released. 1. Pull the release leve...

  • Page 110

    2. Move to the outside of the vehicle, reach into the opening beneath the center of the hood and push up the safety latch lever to release it, before raising the hood. 3. Raise the hood and place the hood prop rod in hood slot to secure the hood in the open position. Hood release lever hood safety l...

  • Page 111

    Caution! Be sure to disengage the rod and secure it in close position before closing the hood. Damage may occur. Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 inches (15 cm), and then drop it. This should secure both latches....

  • Page 112

    Lights multifunction lever the multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, high beams, parking lights, passing light and turn sig- nals. Note: the external lights can only be turned on with the ignition in the on/run position. Headli...

  • Page 113

    Note: when the headlights are turned on, the daytime running lights will be deactivated. Daytime running lights — if equipped to activate the daytime running lights (drl), rotate the end of the multifunction lever to the o symbol. Note: • the low beams and side/tail lights will not be on with drl. T...

  • Page 114

    Parking lights to turn on the parking lights, remove the key or turn the ignition to off/lock position and turn on the headlights. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn sign...

  • Page 115

    Deactivation pull the multifunction lever toward the steering wheel and hold it for more than two seconds. Front fog lights — if equipped the fog light switch is located on the center stack of the instrument panel, just below the radio. Push the switch once to turn the front fog lights on. Push the ...

  • Page 116

    Windshield wipers and washers the windshield wiper/washer lever is located on the right side of the steering column. Note: the windshield wipers/washers will only oper- ate with the ignition in the on/run position. Front windshield wiper operation there are five different modes of operation for the ...

  • Page 117

    Windshield wiper off this is the normal position of the wiper lever. Intermittent speed rotate the end of the lever upward to the first detent. The wipers will operate at intermittent speed. Low speed rotate the end of the lever upward to the second detent. The wipers will operate at low speed. High...

  • Page 118

    From a passing vehicle. This operation will continue until the lever is released. When the lever is released, the wipers will return to the off position and automatically shut off. Front windshield washer operation pull the windshield wiper/washer lever toward the steering wheel to activate the wash...

  • Page 119

    Rear window wiper/washer rear windshield wiper operation rotate the windshield wiper lever center ring upwards to operate the rear window wiper as follows: • in intermittent mode when the rear window wiper is not operating. • in synchronous mode (at half the speed of the rear window wiper) when the ...

  • Page 120

    To unlock the steering column, pull the control handle down. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, pull the...

  • Page 121

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the on/off button and resetting the des...

  • Page 122

    To set a desired speed turn the electronic speed control on. When the vehicle has reached the desired speed, push the set (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. Note: the vehicle should be traveling at a steady speed and on level ground be...

  • Page 123

    • if the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed will be established. Metric speed (km/h) • pushing the res (+) button once will result in a 1 km/h increase in set speed. Each subsequent tap of the button results in a...

  • Page 124

    To accelerate for passing press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using electronic speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the electronic speed control system ma...

  • Page 125

    The parksense® rear park assist is automatically acti- vated when the transmission is placed into reverse. As the distance from an obstacle behind the vehicle de- creases, the audible alert becomes more frequent. Interaction with trailer towing the rear park assist system is automatically deactivate...

  • Page 126

    If several obstacles are detected, the parksense® rear park assist system indicates the nearest obstacle. The minimum height of a detectable obstacle corre- sponds to the maximum height of an obstacle that would clear the underside of the car during the parking maneu- ver. Parksense® rear park assis...

  • Page 127

    Audible and visual signals supplied by the parksense® rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loudspeaker) • sound pulses emitted at a rate that increases as the distance decreases. • emits...

  • Page 128

    While audible signals are emitted, the audio system is not muted. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the distance measured by the inner sensors is constant. If this condition occurs for the external sensors, the signal is turned...

  • Page 129

    Parksense® rear park assist system usage precautions note: • ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the rear park assist system operating properly. • jackhammers, large trucks, and other vibrations co...

  • Page 130

    Warning! • drivers must be careful when backing up even when using parksense®. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue...

  • Page 131

    Parkview® rear back up camera — if equipped your vehicle may be equipped with the parkview® rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the touchscreen display alon...

  • Page 132

    Zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 3 ft (30 cm - 1 m) green 3 ft or greater (1 m or greater) warning! Drivers must be careful when backing up even when using the parkview® rear back up camera. Always check carefully behind your vehicle, and be sure to che...

  • Page 133

    Note: if snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Power outlets passenger compartment power outlets the cigar lighter and the power socket are located in the center console, and both ope...

  • Page 134

    Note: do not connect devices with power higher than 180w to the outlet. Using unsuitable adaptors may damage the outlet. Load compartment power outlet underhood power outlet fuse locations 1 — #85 fuse 15a blue rear power outlet 12v 2 — #86 fuse 15a blue ip power outlet 12v 132 understanding the fea...

  • Page 135

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 136

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 137

    Cupholder a cupholder is located in the front and rear of the center console. Storage glove compartment the glove compartment is located on the passenger side of the instrument panel. Pull on the release handle to open the glove compartment. Note: the glove compartment handle is equipped with a lock...

  • Page 138

    Dash storage the dash storage is located on the right side of the instrument panel above the glove compartment. Overhead console storage there is additional shelf storage above the front sun visors. Dash storage overhead console storage location 136 understanding the features of your vehicle.

  • Page 139

    Cargo area features rear cargo tie-downs to make it easier to secure your load, there are hooks (if equipped) fixed to the floor. Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes (c...

  • Page 140

    Warning! (continued) only, not for passengers, who should sit in seats and use seat belts. • cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or accident, a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only...

  • Page 141

    Position and the lights are always on. Leave the lens in the center position, and the light is turned on and off when the doors are opened or closed. Cargo compartment light — if equipped the cargo compartment light comes on automatically when the swing doors are opened and turns off when the doors ...

  • Page 142

    Rear window features rear window defroster — if equipped the rear window defroster button is located in the center of the instrument panel, below the radio. Push this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indica- tor in the button will illuminat...

  • Page 143

    Roof luggage rack — if equipped the crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Note: if not equipped with crossbars, your authorized ...

  • Page 144

    Caution! • to prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without the crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other ...

  • Page 145: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .145 䡵 instrument cluster . . . . . . . . . . . . . . . . .146 䡵 instrument cluster descriptions . . . . .147 䡵 electronic vehicle information center (evic) . . . . . . . . . . . . . . . . . . . . . . .160 ▫ c...

  • Page 146

    䡵 radio operation and mobile phones . .180 ▫ general information . . . . . . . . . . . . . . . . . . .180 䡵 climate controls . . . . . . . . . . . . . . . . . . .181 ▫ manual climate controls . . . . . . . . . . . . . . . .181 䡵 uconnect® voice recognition quick tips . . . . . . . . . . . . . . . . ...

  • Page 147

    Instrument panel features 1 — air outlet 7 — upper dash storage 13 — climate controls 2 — multifunction lever (external lights 8 — radio 14 — usb charger/aux 3 — instrument cluster 9 — passenger air bag 15 — driver air bag 4— horn 10 — lower dash storage 16 — uconnect® phone buttons 5— electronic sp...

  • Page 148

    Instrument cluster 146 understanding your instrument panel.

  • Page 149

    Instrument cluster descriptions 1. Speedometer the speedometer shows the vehicle speed in miles per hour (mph) and/or kilometers per hour (km/h). 2. Low fuel light the low fuel light will come on when approximately 2–6 gal (9–11 l) remains in the tank, the light will stay on and a single chime will ...

  • Page 150

    7. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or w...

  • Page 151

    8. Generic warning light the generic warning light will illuminate if any of the following conditions occur: • air bag warning light fault, (if the generic warning light starts flashing have your vehicle serviced by an authorized dealer immediately) • engine oil pressure sensor failure • parking sen...

  • Page 152

    To switch the headlights to high beam. Pull the lever a second time to switch the headlights back to low beam. Note: if the driver’s door is open, and the headlights or park lights are left on, the high beam indicator light will remain illuminated and a chime will sound until lights have been turned...

  • Page 153

    15. Seat belt reminder light when the ignition switch is first turned to on/run, if the driver seat belt is unbuckled, a chime will sound. When driving, if the driver or front passenger(s) is unbuckled, a chime will sound and this light will turn on. The seat belt reminder light will flash or remain...

  • Page 154

    Indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) as an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one...

  • Page 155

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 156

    20. Charging system light — if equipped this light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first turned to on/run and remain on briefly as a bulb check. If the charging system light remains on, or comes on while driving, it means tha...

  • Page 157

    Caution! (continued) driveability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can ...

  • Page 158

    Transmission gear range (prnd) the transmission gear range (p,r,n,d) is displayed. When operating in electronic range select (ers) mode, the actual top gear limit (1,2,3, etc.) is displayed. For further information on ers, refer to “nine-speed auto- matic transmission” in “starting and operating.” 2...

  • Page 159

    28. Transmission temperature warning light — if equipped this light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on while driving, safely pull over and stop the vehicle. Then, shift the transmission in...

  • Page 160

    Problem is related to the brake booster, the abs pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure of a portion of the hydraulic system. A leak in either half of the du...

  • Page 161

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 30. Transmission fault indicator this light will illuminate (together with...

  • Page 162

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. This system allows the driver to select a variety of useful information by pushing the switches mounted on the instrument p...

  • Page 163

    • service • daylights • exit menu the system allows the driver to select information by pushing the following buttons mounted on the instru- ment panel to the right of the steering column: note: if equipped with uconnect(r) 5.0/5.0n radio, some customer programmable features will display and managed...

  • Page 164

    • up arrow button push and release the up arrow button to scroll upward through the main menu and submenus. • down arrow button push and release the down arrow button to scroll downward through the main menu and submenus. Dimmer: with headlights on and without entering in the menu, push the up or do...

  • Page 165

    Change engine oil indicator system change engine oil your vehicle is equipped with an engine oil change indicator system. The “change engine oil” message will display in the evic display. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluct...

  • Page 166

    Trip button the trip button, located on the right steering column stalk, can be used to display and to reset the previously described values. • a short button push displays the different values. • a long button push resets the system and then starts a new trip. New trip to reset: • push and hold the...

  • Page 167

    Trip functions both trip functions are resettable (reset — start of new trip). “trip a” can be used to display the figures relating to: • range • trip distance a • average economy a • instantaneous economy • average speed a • travel time a (driving time) • reset trip a “trip b” can be used to displa...

  • Page 168

    Note: the range depends on several factors: driving style, type of route (freeway, residential, mountain roads, etc.), conditions of use of the car (load, tire pressure, etc.). Trip planning must take into account the above notes. Distance traveled this value shows the distance covered since the las...

  • Page 169

    Uconnect® 5.0 buttons on the touchscreen and buttons on the faceplate 1 — uconnect® buttons on the touchscreen 2 — uconnect® buttons on the faceplate uconnect® 5.0n buttons on the touchscreen and buttons on the faceplate 1 — uconnect® buttons on the touchscreen 2 — uconnect® buttons on the faceplate...

  • Page 170

    Buttons on the faceplate buttons on the faceplate are located below the uconnect® system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.E., 30, 60, 90), push the ...

  • Page 171

    When making a selection, press the button on the touch- screen to enter the desired mode. Once in the desired mode, press and release the preferred setting. Once the setting is complete, either press the back arrow button on the touchscreen or the back button on the faceplate to return to the previo...

  • Page 172

    The desired language button. The button will highlight showing that setting has been selected. Press the arrow back/done button on the touchscreen to return to the previous menu. • units — if equipped press the units button to select the correct unit for temperature (°f or °c), distance (mi or km) a...

  • Page 173

    “sync with gps time” button on the touchscreen. The button will highlight showing that setting has been selected. Press the back arrow/done button on the touchscreen to return to the previous menu, or push the back button on the faceplate. • set time hours this feature allows you to adjust the hours...

  • Page 174

    Previous menu. If 24h is selected, the am/pm buttons on the touchscreen will be greyed out (unavailable). • set date this feature will allow you to set the date manually. Press the set date button on the touchscreen and using the “up” and “down” arrows, set the date. Press the back arrow/done button...

  • Page 175

    Lights after pressing the lights button on the touchscreen the following settings will be available: • daytime running lights — if equipped when this feature is selected, the headlights will turn on whenever the engine is running. To make your selection, press the daytime running lights button on th...

  • Page 176

    “no.” the button will highlight indicating that the set- ting has been selected. Press the back arrow/done button on the touchscreen to return to the previous menu. • flash lights with lock when this feature is selected, the exterior lights will flash when the doors are locked with the remote keyles...

  • Page 177

    Note: bass/mid/treble allow you to simply slide your finger up or down to change the setting as well as press directly on the desired setting. • speed adjusted volume this feature increases or decreases volume relative to vehicle speed. To change the speed adjusted volume press the off, 1, 2 or 3 bu...

  • Page 178

    Phone/bluetooth® after pressing the “phone/bluetooth®” button on the touchscreen the following settings will be available: • paired phones this feature shows which phones are paired to the phone/bluetooth® system. For further information, refer to the uconnect® supplement manual. • paired audio sour...

  • Page 179

    Write down the sirius id numbers for your receiver. To reactivate your service, either call the number listed on the screen or visit the provider online. Note: siriusxm travel link is a separate subscription and is available for u.S. Residents only. Restore settings — if equipped after pressing the ...

  • Page 180

    Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support the ipod® control features. Please visit apple’s website for software updates. For further information, refer to the uconnect® supple- ment manual. Steering wheel audio cont...

  • Page 181

    The right hand control is a rocker type switch with a push-button in the center. Pushing the top of the switch will increase the volume, and pushing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to radio, aux or other ...

  • Page 182

    Radio operation and mobile phones under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the mobile phone. This condition is not harmful to the radio. If your radio perform...

  • Page 183

    Climate controls manual climate controls the manual climate controls consist of a series of rotary dials, and three push buttons. 1. Temperature control rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial counter clockwise into the blue area...

  • Page 184

    Economy mode if economy mode is desired, push the a/c button to turn off the indicator light and the a/c compressor. Then, move the temperature control to the desired temperature. 3. Recirculation control push this control button to change the system between recirculation mode and outside air mode. ...

  • Page 185

    • panel air is directed through the outlets in the instrument panel. These outlets can be ad- justed to direct airflow. Note: the center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear. • bi-level air is directed through...

  • Page 186

    Speed increases as you move the control to the right from the “0” (off) position. There are four blower speeds. Rear window/mirror defrosting push, and release the rear window defrost button to turn the function on/off. The activation of the rear defroster is indicated by the rear defrost warning li...

  • Page 187

    Air distribution selection rotate the mode control knob to manually select one of the five possible air distribution settings in the passenger compartment: air flow to the front windshield, front side win- dow and front/rear footwell diffusers. Air flow to the front/rear footwell diffusers. This air...

  • Page 188

    Uconnect® voice recognition quick tips introducing uconnect® start using uconnect® voice recognition with these helpful quick tips. It provides the key voice commands and tips you need to know to control your uconnect® 5.0 system. Key features: • 5.0” full color touchscreen display • bluetooth® with...

  • Page 189

    1. Visit uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing in- structions. 2. Reduce background noise. Wind and passenger con- versations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing straight a...

  • Page 190

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect® system. Push the vr button . After the beep, say ѧ • cancel to stop a current voice session • help to hear a list of suggested voice commands • repeat to listen to the system prompts again notice...

  • Page 191

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio® stations you would like to hear. (sub- scription or included siriusxm satellite radio trial re- quired.) push the vr button . After the beep, say ѧ • tune to ninety-five-point-five fm • tune to satellite channel hits 1 ti...

  • Page 192

    Media uconnect® offers connections via usb, bluetooth® and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod® devices. (cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands and follow t...

  • Page 193

    Phone making and answering hands-free phone calls is easy with uconnect®. When the phonebook button is illumi- nated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the foll...

  • Page 194

    Voice text reply uconnect® will announce incoming text messages. Push the phone button and say listen. (must have com- patible mobile phone paired to uconnect® system.) 1. Once an incoming text message is read to you, push the phone button . After the beep, say: “reply” 2. Listen to the uconnect® pr...

  • Page 195

    Additional information © 2015 fca us llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of fca us llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. Yelp, yelp logo, yelp...

  • Page 197: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .199 ▫ automatic transmission . . . . . . . . . . . . . . . .199 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .199 ▫ extreme cold weather (below –20°f or −29°c) . . . . . . . . . . . . . . . .200 ▫ ex...

  • Page 198

    䡵 power steering . . . . . . . . . . . . . . . . . . . . .216 ▫ power steering fluid check . . . . . . . . . . . . . .217 䡵 parking brake . . . . . . . . . . . . . . . . . . . . . .218 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . .220 䡵 electronic brake control system . . . .221 ▫ four...

  • Page 199

    ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . .250 ▫ tread wear indicators . . . . . . . . . . . . . . . . . .250 ▫ life of tire . . . . . . . . . . . . . . . . . . . . . . . . .251 ▫ replacement tires . . . . . . . . . . . . . . . . . . . . .251 䡵 tire chains (traction devices) . . ...

  • Page 200

    䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . . . .283 ▫ towing this vehicle behind another vehicle . .283 ▫ recreational towing — automatic transmission . . . . . . . . . . . . . . . . . . . . . . . . .284 198 starting and operating.

  • Page 201

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 202

    Extreme cold weather (below –20°f or −29°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. To prevent possible engine damage while starting at low temperatures, this vehicle will i...

  • Page 203

    If engine fails to start warning! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. Caution! • do not attempt to push or tow your vehicle to get it started. Vehicl...

  • Page 204

    The engine block heater cord is routed under the hood, behind to the driver’s side headlamp. Follow the steps below to properly use the engine block heater: 1. Locate the engine block heater cord (behind the driv- er’s side headlamp). 2. Undo the velcro strap that secures the heater cord in place. 3...

  • Page 205

    Warning! (continued) your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake ...

  • Page 206

    Caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into or out of park or reverse only after the vehicle has come to a complete stop. • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting i...

  • Page 207

    Lock button on the shift lever and move the lever rear- ward or forward. You must also press the brake pedal to shift the transmission out of park, or to shift from neutral into drive or reverse when the vehicle is stopped or moving at low speeds (refer to ⬙brake/ transmission shift interlock system...

  • Page 208

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 209

    Downhill grade and away from the curb on an uphill grade. Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and oth...

  • Page 210

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 211

    • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral (n) use this range when the vehicle is standing for prolonged periods with the...

  • Page 212

    Automatically upshifts through all forward gears. The drive position provides optimum driving characteris- tics under all normal operating conditions. When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading condi- tions, in hilly terrain or traveling into s...

  • Page 213

    Mode is activated. In this mode, the transmission remains in fourth gear regardless of which forward gear is selected. Park, reverse, and neutral will continue to operate. The malfunction indicator light (mil) may be illuminated. Limp home mode allows the vehicle to be driven to an authorized dealer...

  • Page 214

    Note: the torque converter clutch will not engage until the transmission fluid is warm [usually after 1 to 3 miles (2 to 5 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting properly when cold. This ...

  • Page 215

    Note: to select the proper gear position for maximum deceleration (engine braking), move the shift lever into the ers position, then simply press and hold it forward (-). The transmission will shift to the range from which the vehicle can best be slowed down. Driving on slippery surfaces acceleratio...

  • Page 216

    Traction when driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observ...

  • Page 217

    Shallow standing water although your vehicle is capable of driving through shallow standing water, consider the following cautions and warnings before doing so. Warning! • driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through ...

  • Page 218

    Caution! (continued) operate the vehicle if any fluid appears contami- nated, as this may result in further damage. Such damage is not covered by the new vehicle limited warranty. • getting water inside your vehicle’s engine can cause it to lock up and stall out, and cause serious internal damage to...

  • Page 219

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Power steering fluid check checking the power steering fluid level at a define...

  • Page 220

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave an automatic transmission in park, or manual transmission in reverse or first gear. The parking brake lever is located in the center console. To apply the parking brake, pull the le...

  • Page 221

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 222

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic trans- mission in park, a manual transmission in re- verse or first gear. Failure to do so may cause the vehicle to roll and cause...

  • Page 223

    Electronic brake control system your vehicle is equipped with a advanced electronic brake control system that includes the anti-lock brake system (abs), brake assist system (bas), traction con- trol system (tcs), hill start assist (hsa), and electronic stability control (esc). All systems work toget...

  • Page 224

    Warning! (continued) • the abs cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • the capabilities of an abs-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize t...

  • Page 225

    Warning! • the brake assist system (bas) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevail- ing road conditions. • the bas cannot prevent collisions, including those resulting from excessive speed in turns, driving on very sli...

  • Page 226

    Pressure and the vehicle will roll down the hill. The system will release brake pressure in proportion to the amount of throttle applied as the vehicle starts to move in the intended direction of travel. Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehic...

  • Page 227

    Electronic stability control (esc) this system enhances directional control and stability of the vehicle under various driving conditions. Esc cor- rects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteering or und...

  • Page 228

    Esc activation/malfunction indicator light and esc off indicator light the esc activation/malfunction indicator light in the instrument cluster will come on when the ignition switch is turned to the mar (on/run) position for four seconds. If the esc activation/malfunction indicator light comes on co...

  • Page 229

    Esc operating modes the esc system has two available operating modes. Full on this is the normal operating mode for esc. Whenever the vehicle is started the system will be in this mode. This mode should be used for most driving situations. Esc should only be turned to “partial off” for specific reas...

  • Page 230

    Note: to improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow, sand, or gravel, it may be desirable to switch to the “partial off” mode by momentarily pressing the “esc off” button. Once the situation requiring “partial off” mode is overcome, turn esc back ...

  • Page 231

    Warning! Many factors, such as vehicle loading, road condi- tions, and driving conditions, influence the chance that wheel lift or rollover may occur. Erm cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. The capabili...

  • Page 232

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 233

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ....Blank....ⴖ = passenger car tire based on european design standards, or lt = light truck tire based o...

  • Page 234

    Example: r = construction code – ⬙r⬙ means radial construction, or – ⬙d⬙ means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the r...

  • Page 235

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 236

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 237

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 238

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 236 starting an...

  • Page 239

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 240

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this manual. To determine the maximum loading conditions of your v...

  • Page 241

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 242

    240 starting and operating.

  • Page 243

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 244

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 245

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 246

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits ...

  • Page 247

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 248

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 249

    Run flat tires — if equipped run flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the run flat mode. A run flat mode occurs when the tire inflation pressure is of/or below 14 psi...

  • Page 250

    Rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looki...

  • Page 251

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 252

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 253

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. L...

  • Page 254

    Wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed. Refer to the paragraph on “tread wear indicator”. Refer to the tire and loading information placard or ...

  • Page 255

    Warning! (continued) • never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • failure to equip your vehicle wi...

  • Page 256

    Tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a smooth, quiet ride. Refer to the “maintenance schedule” for the proper maintenance intervals. The reasons for any rapid or unusual wear should be corrected prior to rotation being perfor...

  • Page 257

    The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after th...

  • Page 258

    Pressure is sufficiently low enough to turn on the tire pressure monitoring telltale light. Driving the vehicle may cause the tire pressure to rise to approximately 27 psi (186 kpa), but the tire pressure monitoring telltale light will still be on. In this situation, the tire pressure monitoring tel...

  • Page 259

    • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handlin...

  • Page 260

    Tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster, an audible chime will be activated, and a proper text message will be displayed when one or more of the four active road tire pressures are low. Should this occur, ...

  • Page 261

    Note: your vehicle can be equipped with either tire service kit, compact spare tire or regular size spare tire (with or without original tpms sensor). 1. Tire service kit (original tire sealant – if equipped): after fixing the punctured tire with original tire seal- ant, the original situation will ...

  • Page 262

    General information this device complies with part 15 of the fcc rules and rss-210 of industry canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may caus...

  • Page 263

    Than 87 can cause engine failure and may void or not be covered by the new vehicle limited warranty. Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consid- ering service for the vehicle...

  • Page 264

    Are not the responsibility of the manufacturer and may void or not be covered under new vehicle limited warranty. E-85 usage in non-flex fuel vehicles non-flex fuel vehicles (ffv) are compatible with gaso- line containing up to 15% ethanol (e-15). Gasoline with higher ethanol content may void the ne...

  • Page 265

    Materials added to fuel besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended. Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle perfor- mance....

  • Page 266

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the respon...

  • Page 267

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel the gas cap is located behind the fu...

  • Page 268

    5. Remove gasoline nozzle, reinstall fuel cap and close fuel filler door. Caution! • damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap. A poorly fitting cap could let impurities into the fuel system and may cause the “malfunction indi...

  • Page 269

    • if the gas cap is not tightened properly, the mil may come on. Be sure the gas cap is tightened every time the vehicle is refueled. Vehicle loading as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door ...

  • Page 270

    Evenly. Make sure that you do not exceed either front or rear gawr. Warning! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle...

  • Page 271

    The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to ensure that it is not over the gvwr. Figure out the weight on the front and rear of the vehicle separately. It is important that you distribut...

  • Page 272

    Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load ...

  • Page 273

    Tongue weight (tw) the tongue weight is the downward force exerted on the hitch ball by the trailer. The recommended tongue weight is 10% to 15% of the vehicle’s gtw for a conventional hitch. You must consider this as part of the load on your vehicle. Frontal area the frontal area is the maximum hei...

  • Page 274

    Weight-distributing hitch a weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s direc...

  • Page 275

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 276

    Trailer towing weights (maximum trailer weight ratings) note: for additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • ramtrucks.Com/en/towing_guide/ • ramtruck.Ca (canada) • rambodybuilder.Com trailer and tongue weight always load a tr...

  • Page 277

    Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weight of the driver and all passengers. Note: remember that everything put into or on the...

  • Page 278

    Perform the maintenance listed in the “maintenance schedule.” refer to “maintenance schedule” for the proper maintenance intervals. When towing a trailer, never exceed the gawr or gcwr ratings. Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as s...

  • Page 279

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized. Towing requirements — tires • do not attempt to tow a trailer while ...

  • Page 280

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • an electronically actuated trailer brake controller is required when towing a trailer w...

  • Page 281

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing requirements — trailer lights an...

  • Page 282

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 283

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic transmission the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. ...

  • Page 284

    Electronic speed control — if equipped • do not use in hilly terrain or with heavy loads. • when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. • use speed control in flat terrain and with light loads to maxim...

  • Page 285

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground automatic transmission flat tow none not allowed dolly tow front ok rear not allowed on trailer all ok note: when recreationally towing your vehicle, always follow applicabl...

  • Page 286

    Recreational towing — automatic transmission recreational towing is allowed only if the front wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure: 1. Properly secure the dolly to the tow vehicle, following the dolly ma...

  • Page 287: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .287 䡵 if your engine overheats . . . . . . . . . . . .287 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .288 ▫ torque specifications . . . . . . . . . . . . . . . . . . .289 䡵 tire se...

  • Page 288

    ▫ front tow eye installation . . . . . . . . . . . . . . .319 ▫ rear tow eye installation . . . . . . . . . . . . . . . .319 䡵 towing a disabled vehicle . . . . . . . . . . .320 䡵 shift lever override . . . . . . . . . . . . . . . .321 䡵 ignition key removal override . . . . . . .323 286 what to do ...

  • Page 289

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel above the climate controls. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency....

  • Page 290

    Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads hot (h), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on hot (h), and you hear conti...

  • Page 291

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 63 ft-lbs (86 n·m) steel wheels only 89 ft-lbs (120 n·m) aluminum wheels only m12 x 1.25 17 mm **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. ...

  • Page 292

    After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may ...

  • Page 293

    Tire service kit storage — if equipped the tire service kit is located under the passenger seat. Tire service kit usage if a tire is punctured, you can make a first emergency repair using the tire service kit located under the passenger seat. Tire punctures of up to 1/4” (6 mm) can be repaired; the ...

  • Page 294

    Warning! • do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the tire service kit. • do not use tire service kit or drive the vehicle under the following circumstances: – if the puncture in the tire t...

  • Page 295

    Warning! (continued) • tire service kit sealant solution contains latex. In case of an allergic reaction or rash, consult a phy- sician immediately. Keep tire service kit out of reach of children. If swallowed, rinse mouth imme- diately with plenty of water and drink plenty of water. Do not induce v...

  • Page 296

    Warning! (continued) failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, and others around you. Have the tire checked as soon as possible at an authorized dealer. If the pressure is at 19 psi (1.3 bar) or above repeat the inflation process to reac...

  • Page 297

    Warning! Store the sealant canister in its special compartment, away from sources of heat. Failure to follow this warning may result in sealant canister rupture and serious injury or death. Jacking and tire changing — if equipped warning! • do not attempt to change a tire on the side of the vehicle ...

  • Page 298

    Removing the spare tire 1. Remove the spare tire before attempting to jack up the vehicle. Attach the wrench handle to the winch exten- sion. Jack/tools location jack tools 1 — wrench handle 2 — tow eye 3 — winch extension 4 — emergency screwdriver 5 — bolt install wrench 6 — wheel chock 7 — jack 29...

  • Page 299

    2. To access the winch mechanism open the rear doors of the vehicle to expose the winch mechanism access cover. Remove the access cover and install the winch extension into the winch mechanism. 3. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable...

  • Page 300

    4. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. 5. Remove the retainer nut prior to removing the retainer from the wheel. Spare tire retainer nut 298 what to do in emergencies.

  • Page 301

    6. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. 7. Pull the retainer through the center of the wheel. Lifting spare tire retainer 6 what to do in emergencies 299.

  • Page 302

    Preparations for jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operati...

  • Page 303

    Warning! (continued) • turn on the hazard warning flasher. • block the wheel diagonally opposite the wheel to be raised. • set the parking brake firmly and set an automatic transmission in park; a manual transmission in reverse. • never start or run the engine with the vehicle on a jack. • do not le...

  • Page 304

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Loosen (but do not remove) the wheel lug bolts with the wrench handle by turning them to the left one turn while the wheel is still on the ground. 2. There...

  • Page 305

    Note: place the jack underneath the jack engagement location that is closest to the flat tire. Jack engaged to body flange front jacking location 6 what to do in emergencies 303.

  • Page 306

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated. Warning! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you...

  • Page 307

    4. Raise the vehicle by turning the jack screw to the right until the tire just clears the surface and enough clear- ance is obtained to install the spare tire. Minimum tire lift provides maximum stability. Front jacking location engaged rear jacking location engaged 6 what to do in emergencies 305.

  • Page 308

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel lug bolts. For vehicles with wheel covers, remove the cover from the wheel by hand. Do not p...

  • Page 309

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. 7. Lower the vehicle by turning the jack screw to the left. 8. Refer to “torque specifications” in this...

  • Page 310

    Note: for vehicles with alloy wheels remove the adapter bracket and bolts from the storage bag in the glove compartment. Take the adapter and fit the plastic spacer between the spring and the flange of the bracket. The plastic fin must be directed downwards and per- fectly coincide with the flange c...

  • Page 311

    11. Stow the jack and tools under the drivers seat. 12. Check the spare tire pressure as soon as possible. Correct the tire pressure, as required. Adapter/bracket 1 — adapter 2 — bracket 3 — pin alloy wheel mounting 6 what to do in emergencies 309.

  • Page 312

    Vehicles equipped with wheel covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two wheel bolts on the wheel. Install the wheel bolts with the threaded end of the bolt toward the wheel. Lightly tighten the wheel bolts. 3. Align ...

  • Page 313

    Snapping the cover over the two wheel bolts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining wheel bolts with the threaded end of the wheel bolt toward the wheel. Lightly tighten the wheel bolts. Warning! To avoid the risk of forcing the vehicle off the jack, do...

  • Page 314

    Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electrical system may occur. Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode ...

  • Page 315

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 316

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end...

  • Page 317

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the dis- charged battery. 2. Disconnect the opposite end of the negative (-) jumper cable...

  • Page 318

    Caution! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the en- gine to idle with the transmission in neutral for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure d...

  • Page 319

    Warning! (continued) explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping when you are stuck. And do not let anyone near a spinning wheel, no matter what the speed. Tow eye usage — if equipped your ...

  • Page 320

    • the tow eye is recommended for use with an approved tow bar and or rope. • do not use the tow eye to pull the vehicle onto a flatbed truck. • do not use the tow eye to free a stuck vehicle. Refer to “freeing a stuck vehicle” in this section for further information. Warning! Stand clear of vehicles...

  • Page 321

    Caution! • the tow eye must be used exclusively for roadside assistance operations. Only use the tow eye with an appropriate device in accordance with the highway code (a rigid bar or rope) to flat tow the vehicle for a short distance to the nearest service location. • tow eyes must not be used to t...

  • Page 322

    Insert the wheel bolt wrench handle through the eye and tighten, refer to “jacking and tire changing” for further information. The tow eye must be fully seated to the attaching bracket through the lower rear fascia. If the tow eye is not fully seated to the attaching bracket, the vehicle should not ...

  • Page 323

    If the ignition key is unavailable, or the vehicle’s battery is discharged, refer to “shift lever override” in this section for instructions on shifting the transmission out of park for towing. Caution! • do not use sling-type equipment when towing. Vehicle damage may occur. • when securing the vehi...

  • Page 324

    4. Push and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool down into the shift lever override access hole (at the right front corner of the shift lever assembly) then push and hold the override release lever down. 6. Move the shift lever to the neutral posit...

  • Page 325

    Ignition key removal override this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. To remove the key manually, proceed as follows: 1. Firmly apply the parking brak...

  • Page 326

    7. Once the key is removed, reinstall the steering column cover. Caution! It is advisable to contact your authorized dealer to have the reinstall procedure carried out. If you would like to proceed in performing the reinstall procedure special attention must be paid to the correct coupling of the cl...

  • Page 327: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.4l . . . . . . . . . .327 䡵 onboard diagnostic system — obd ii . .328 ▫ loose fuel filler cap message . . . . . . . . . . . .328 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . . .329 䡵 replace...

  • Page 328

    ▫ automatic transmission . . . . . . . . . . . . . . . .352 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .354 䡵 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .360 ▫ underhood fuses. . . . . . . . . . . . . . . . . . . . . .361 ...

  • Page 329

    Engine compartment — 2.4l 1 — air cleaner filter 5 — power distribution center (fuses) 2 — power steering fluid reservoir 6 — washer fluid reservoir 3 — oil fill cap 7 — engine coolant pressure cap 4 — brake fluid reservoir 8 — engine oil dipstick 7 maintaining your vehicle 327.

  • Page 330

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 331

    “electronic vehicle information center (evic)” in ”un- derstanding your instrument panel” for further informa- tion. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tight- ened. Push the odometer reset button to turn the message off. If the p...

  • Page 332

    Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station. To check if your vehicle’s obd ii system is ready, you must do the following: 1. Cycle the ignition switch to the on position, but do not crank or start the engine. Note: if you crank or start the...

  • Page 333

    Before going to the i/m station. The i/m station can fail your vehicle because the mil is on with the engine running. Replacement parts use of genuine mopar® parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by th...

  • Page 334

    Besides those maintenance items specified in the fixed “maintenance schedule”, there are other components which may require servicing or replacement in the future. Caution! • failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs...

  • Page 335

    On the dipstick. Adding 1 quart (0.9 l) of oil when the reading is at the bottom of the safe zone will result in a reading at the top of the safe zone on these engines. Caution! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Chan...

  • Page 336

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity (sae grade) — 2.4l engine mopar® sae 0w-20 engine oil or equivalent pennzoil® or shell helix® is recommended for all o...

  • Page 337

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 338

    Used to assure most efficient service. Mopar® engine air cleaner filters are a high quality filter and are recom- mended. Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fl...

  • Page 339

    Caution! (continued) (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. • if a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables be- fore connecting the charger to the...

  • Page 340

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r134a — if equipped r-134a air conditioning refrigerant is a hydrofl...

  • Page 341

    The application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, t...

  • Page 342

    2. Turn the ignition to the mar-on position then to stop. 3. After turning the ignition to the stop, within two minutes move the right stalk upward, into the un- stable (“anti-panic”) position, for at least half of a second. The windshield wiper then executes part of a stroke; at each command, appro...

  • Page 343

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine ...

  • Page 344

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 345

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 346

    For any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiat...

  • Page 347

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 348

    Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze) that meets the requirements of fca material standard ms.90032. When adding engine coolant (antifreeze): • we recommend using mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic...

  • Page 349

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery tank. The cap should be inspected and cleaned if there is any accumulation of foreign mater...

  • Page 350

    Engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Coolant level the coolant expansion bottle provides a quick visual method for determining that the coolant l...

  • Page 351

    • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (anti- freeze) needs to be added, the contents of the coolant expansion bottle must also be protected against freez- ing. • if frequent engine coolant (antifreeze) additions are required, the cool...

  • Page 352

    Warning! (continued) high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency. Brake master cylinder the fluid in the master cylinder should be checked when performing under hood services or immediately if the “brake war...

  • Page 353

    Warning! (continued) cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or pro- longed braking, resulting in sudden brake failure. This could result in a col...

  • Page 354

    Automatic transmission selection of lubricant it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “fluids, lubricants, and genuine parts” in this section for fluid specifications....

  • Page 355

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 356

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons a...

  • Page 357

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover to remove. • use a high quality cleaner wax, such as mopar® cleaner wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • av...

  • Page 358

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • use mopar® touch up paint on scratches as soon as possible. You...

  • Page 359

    Stain repel fabric cleaning procedure — if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar® total clean, or a mild ...

  • Page 360

    Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar® total clean o...

  • Page 361

    Cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or windows equipped with radio antennas. Do not use scrapers or other sharp instrument that may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or cloth that you are usi...

  • Page 362

    Warning! (continued) assemblies must be replaced after a collision if they have been damaged (i.E., bent retractor, torn web- bing, etc.). Fuses warning! • when replacing a blown fuse, always use an ap- propriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse wi...

  • Page 363

    Underhood fuses the front distribution unit is located on the right side of the engine compartment, next to the battery. To access the fuses, remove fasteners and remove the cover. The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Front dis...

  • Page 364

    Cavity maxi fuse mini fuse description f01 60 amp blue body controller f02 40 amp orange front heated seats, second 12 volt ip outlet f02 60 amp blue rear power window including front heated seats, second 12 volt ip outlet f03 20 amp yellow ignition switch f04 40 amp orange bsm system module f05 50 ...

  • Page 365

    Cavity maxi fuse mini fuse description f15 15 amp blue available f16 5 amp tan ecm and transmission shifter f17 25 amp clear ecm power loads f18 5 amp tan ecm load, main relay f19 7.5 amp brown air conditioning f20 30 amp green rear defroster f21 5 amp tan key unlock f22 10 amp red primary ecm loads...

  • Page 366

    Cavity maxi fuse mini fuse description f84 15 amp blue at module f85 15 amp blue rear power outlet 12v f86 15 amp blue ip power outlet 12v f87 5 amp tan ibs f88 7.5 amp brown external mirror defrost 364 maintaining your vehicle.

  • Page 367

    Interior fuses the interior fuse panel is part of the body control module (bcm) and is located on the driver’s side under the instrument panel. Fuse panel cover 7 maintaining your vehicle 365.

  • Page 368

    Fuse panel cavity locations 366 maintaining your vehicle.

  • Page 369

    Cavity mini fuse description f53 5 amp beige kl 30 (+30) - ipc f38 20 amp yellow central doors locking f36 10 amp red kl 30 (+30) - tpms, eobd, hvac, radio f43 15 amp blue bi-directional washer pump f48 20 amp yellow passenger power windows f50 7.5 amp brown kl 15 (+15) - air-bag f51 7.5 amp brown k...

  • Page 370

    Central unit fuse panel the central power fuse panel is located on the driver’s side under the instrument panel. Fuse panel cover fuse panel 368 maintaining your vehicle.

  • Page 371

    Cavity mini fuse description f1 10 amp red front heated seat driver f2 10 amp red front heated seat passenger f3 20 amp yellow rear power window driver side f4 20 amp yellow rear power window passenger side f5 15 amp blue 2nd instrument panel power outlet 12v vehicle storage if you are leaving your ...

  • Page 372

    Replacement bulbs interior bulbs bulb number front courtesy lamps c10w rear courtesy lamps c10w luggage lamp c5w exterior bulbs bulb number front low beam headlamp h11 front high beam headlamps hb3 front side marker lamps led (see your authorized dealer) front parking/daytime running lamps w21w fron...

  • Page 373

    Bulb number rear tail lamps p21/5w rear side marker lamps led (see your authorized dealer) center mount brake lamp w5w reverse light w16w front fog lamps h11 note: numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your aut...

  • Page 374

    4. Install the bulb and rotate clockwise to lock in place. 5. Reinstall the plastic cap. Front turn signal lamps front to change the bulb, proceed as follows: 1. Remove the cap from the back of the outer upper headlamp housing. 2. Rotate the bulb counter clockwise and remove. 3. Install the bulb int...

  • Page 375

    Rear tail, stop, backup and turn signal lamps the rear light clusters contain taillight, brake light, direction indicator and reverse/rear fog light bulbs. To access the light clusters, proceed as follows: 1. Open the rear doors. Or liftgate 2. Remove the screws and remove the tail lamp assem- bly. ...

  • Page 376

    License plate lights proceed as follows to replace the bulbs: 1. Disengage the holding tabs and remove the lens by lifting to the left. 2. Remove the bulbs by releasing them from the side contacts; insert the new bulbs and make sure they are correctly clamped between these contacts. Fluid capacities...

  • Page 377

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of fca material standard ms.90032. Engine oil –...

  • Page 378

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 379

    Chassis component fluid, lubricant, or genuine part automatic transmission use only mopar® zf 8&9 speed atf™ automatic transmission fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Brake master cylinder we recommend you use mopar® do...

  • Page 381: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . .380 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .382 8.

  • Page 382

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 383

    • check tire pressure and look for unusual wear or damage. Rotate tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. • check the fluid levels of the coolant reservoir and brake master cylinder, fill as needed. • check function of all interior and e...

  • Page 384

    Maintenance chart mileage: 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 a...

  • Page 385

    Mileage: 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 change brake fluid ...

  • Page 386

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 387: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .387 ▫ prepare for the appointment. . . . . . . . . . . . .387 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .387 ▫ be reasonable with requests ....

  • Page 388

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .393 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .393 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .393 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .394 386 if...

  • Page 389

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 390

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 391

    In mexico contact av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has instal...

  • Page 392

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 393

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 394

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 395

    Call toll free at: • 1-800-890-4038 (u.S.) • 1-800-387-1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 396

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 397: Index

    Index 10

  • Page 398

    Adding engine coolant (antifreeze) . . . . . . . . . . . .345 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .263 air bag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46, 47 air bag advance front air bag . . . . . . . . . . . . . . . . .47, 48 air bag components ....

  • Page 399

    Adding fluid . . . . . . . . . . . . . . . . . . . . . . .353, 377 fluid and filter changes . . . . . . . . . . . . . . . . . .353 fluid change . . . . . . . . . . . . . . . . . . . . . . . . . .353 fluid level check . . . . . . . . . . . . . . . . . . .352, 353 fluid type . . . . . . . . . . . . . ...

  • Page 400

    Car washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .354 cellular phone . . . . . . . . . . . . . . . . . . . . . . . . . . .180 certification label. . . . . . . . . . . . . . . . . . . . . . . . .267 chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253 chart, tir...

  • Page 401

    Corrosion protection . . . . . . . . . . . . . . . . . . . . . . .354 cruise light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135 customer assistance . . . . . . . . . . . . . . . . . . . . . . .387 customer progra...

  • Page 402

    Trip functions . . . . . . . . . . . . . . . . . . . . . . . . .165 emergency, in case of freeing vehicle when stuck . . . . . . . . . . . . . . . .315 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .311 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .320 emission ...

  • Page 403

    Engine oil disposal . . . . . . . . . . . . . . . . . . . . .334 flashers hazard warning . . . . . . . . . . . . . . . . . . . . . . . .287 turn signal . . . . . . . . . . . . . . . . . . . . . . . . .90, 147 flash-to-pass . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 flooded engine sta...

  • Page 404

    Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . .147 tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206 gear select lever override . . . . . . . . . . . . . . . . . .321 general information . . ...

  • Page 405

    Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ipod® control . . . . . . . . . . . . . . . . . . . . . . . . . . .177 ipod®/usb/mp3 control . . . . . . . . . . . . . . . . . . .177 bluetooth® streaming audio . . . . . . . . . . . . . . .177 jump starting . . . . . . . . . ...

  • Page 406

    Tire pressure monitoring (tpms) . . . . . . . . . . . .147 traction control . . . . . . . . . . . . . . . . . . . . . . . .226 turn signal . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 wait to start . . . . . . . . . . . . . . . . . . . . . . . . . . .147 warning (instrument cluster desc...

  • Page 407

    Oil, engine . . . . . . . . . . . . . . . . . . . . . . . . . .332, 375 capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .374 change interval . . . . . . . . . . . . . . . . . . . . . . . .333 checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .332 dipstick . . . . . . ...

  • Page 408

    Radiator cap (coolant pressure cap) . . . . . . . . . . .347 radio operation . . . . . . . . . . . . . . . . . . . . . . . . . .180 rear camera . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 rear parksense system . . . . . . . . . . . . . . . . . . . . .122 rear window defroster . . . . ...

  • Page 409

    Seat belt pretensioner . . . . . . . . . . . . . . . . . . . . .43 seat belt reminder . . . . . . . . . . . . . . . . . . . . . . .34 seat belt system . . . . . . . . . . . . . . . . . . . . . . . . .32 seat belt maintenance . . . . . . . . . . . . . . . . . . . . . .359 seat belt reminder . . . . ....

  • Page 410

    Specifications fuel (gasoline) . . . . . . . . . . . . . . . . . . . . . . . . .375 oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .375 speed control (cruise control). . . . . . . . . . . . . . . .118 speedometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 star...

  • Page 411

    Pressure warning light . . . . . . . . . . . . . . . . . . .147 quality grading . . . . . . . . . . . . . . . . . . . . . . . .393 radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .244 replacement . . . . . . . . . . . . . . . . . . . . . . . . . . .251 rotation . . . . . . . . . ....

  • Page 412

    Transporting pets . . . . . . . . . . . . . . . . . . . . . . . . . .85 tread wear indicators . . . . . . . . . . . . . . . . . . . . . .250 turn signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 uconnect® voice command. . . . . . . . . . . . . . . . . .186 uniform tire quality gr...

  • Page 413

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 414

    P r o m a s t e r c i t y o w n e r ’ s m a n u a l 2 0 1 5 2015 promaster city 15vm-126-ac third edition printed in u.S.A. Fca us llc.