1. DL manuals
  2. RAM
  3. Automobile
  4. Chassi Cab 2011
  5. Owner's Manual

RAM Chassi Cab 2011 Owner's Manual

Summary of Chassi Cab 2011

  • Page 1

    C h a s s i s c a b chrysler group llc o w n e r ’ s m a n u a l 2 0 1 1 2 0 1 1 r a m t r u c k c h a s s is c a b 11dd43-126-ac second edition printed in u.S.A. Ram truck.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 4 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 6 䡵 van conversions/campers . . . . . . . . . . . . . . . . . 6 䡵 vehicle identifi...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 9

    Vehicle identification number the vehicle identification number (vin) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the auto- mobile information disclosure label affixed to a window on your vehicle, the vehicle registration and...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ wireless ignition node (win) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 12 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ removing key fob f...

  • Page 12

    ▫ remote open window feature — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . 24 ▫ programming additional transmitters . . . . . . 24 ▫ transmitter battery replacement . . . . . . . . . . 24 ▫ general information . . . ....

  • Page 13

    ▫ driver and right front passenger supplemental restraint system (srs) – airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 ▫ airbag system components . . . . . . . . . . . . . . 53 ▫ advanced front airbag features . . . . . . . . . . 54 ▫ airbag deployment sensors and controls . . ...

  • Page 14

    A word about your keys key fob with remote keyless entry (rke) — if equipped your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a wireless ignition node (win) with integral ignition switch. You can insert the key fob into th...

  • Page 15

    Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key ...

  • Page 16

    To remove the emergency key, slide the mechanical latch at the top of the key fob sideways with your thumb and then pull the key out with your other hand. Note: you can insert the double-sided emergency key into the lock cylinder with either side up. Removing key fob from ignition place the shift le...

  • Page 17

    (evic)/personal settings (customer-programmable features)” in “understanding your instrument panel” for further information. Warning! • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fata...

  • Page 18

    Sentry key 姞 the sentry key 威 immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses a key fob with a factory-mated remot...

  • Page 19

    All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics. Replacement keys note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to ...

  • Page 20

    General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference...

  • Page 21

    Note: if the vehicle security light stays on continu- ously during vehicle operation, have the system checked by an authorized dealer. To disarm the system use the rke transmitter to unlock the door. If something has triggered the system in your absence, the horn will sound three times when you unlo...

  • Page 22

    Note: • the front courtesy overhead console and door cour- tesy lights do not turn off if the dimmer control is in the “dome on” position (extreme top position). • the illuminated entry system will not operate if the dimmer control is in the “dome defeat” position (extreme bottom position). Remote k...

  • Page 23

    Setup for driver door first, otherwise this will unlock all doors), or twice within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote key unlock, driver door/all doors first this feature lets y...

  • Page 24

    Flash lamps with remote key lock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to “...

  • Page 25

    Sound horn with remote key lock this feature will cause the horn to chirp when the doors are locked with the rke transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to “elec- tronic vehicle informat...

  • Page 26

    Using the panic alarm to turn the panic alarm feature on or off, press and hold the panic button on the rke transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on. Th...

  • Page 27

    1. With the rke transmitter buttons facing down, use a flat blade screwdriver to pry the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. 2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterior...

  • Page 28

    Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m). Note: the vehicle must be equipped with an auto- matic...

  • Page 29

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted - door ajar • remote start aborted - hood ajar • remote start abor...

  • Page 30

    Note: to avoid unintentional shut downs, the system will disable the one time press of the remote start button for two seconds after receiving a valid remote start request. To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, press and release the unlock button on t...

  • Page 31

    Door locks manual door locks front and rear doors may be locked by moving the lock knob down or unlocked by moving the lock knob up. Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed. The emergency key will...

  • Page 32

    Power door locks — if equipped a power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. If you press the power door lock switch while the key fob is in the ignition, and any front door is open, the power locks will not operate. This prevents you from ac...

  • Page 33

    6. The doors were not previously locked using the power door lock switch or remote keyless entry (rke) transmitter automatic door locks programming — if equipped the automatic door locks feature can be enabled or disabled as follows: • for vehicles equipped with the electronic vehicle information ce...

  • Page 34

    Auto unlock doors — if equipped this feature unlocks all of the doors of the vehicle when either front door is opened. This will occur only after the vehicle has been shifted into the park position after the vehicle has been driven (shifted out of park and all doors closed). Auto unlock doors progra...

  • Page 35

    Child-protection door lock to provide a safer environment for children riding in the rear seat, the rear doors (if equipped) of your vehicle have the child-protection door lock system. To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to enga...

  • Page 36

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: • after setting the child-protection door lock system, always test the door from the inside to make certain it is in the des...

  • Page 37

    The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of the crew cab models. The windows will operate when the ig...

  • Page 38

    To open the window part way, press to the first detent and release it when you want the window to stop. Auto-up feature with anti-pinch protection (4-door models driver and front passenger door only) — if equipped lift the window switch fully upward to the second detent, release, and the window will...

  • Page 39

    2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Window lockout switch (4–door models only) the window lockout switch on the driver’s door allows you to disable ...

  • Page 40

    Normal occurrence and can be minimized. If the rear windows are open and buffeting occurs, open the front and rear windows together to minimize the buffeting. Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belt...

  • Page 41

    Warning! In an accident, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckl...

  • Page 42

    Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In an accident, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure ever...

  • Page 43

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as fa...

  • Page 44

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into...

  • Page 45

    Warning! (continued) • a shoulder belt placed behind you will not protect you from injury during an accident. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thigh...

  • Page 46

    Warning! • a lap belt worn too high can increase the risk of internal injury in an accident. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • a twisted belt will not protect you properly. In a coll...

  • Page 47

    Regular cab front center three point belt 1. The front center seat belt on the regular cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger ...

  • Page 48

    Warning! • if the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in an accident. • when reattaching the black latch and black buckle, ensure the seat ...

  • Page 49

    Warning! • if the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in an accident. • when reattaching the black latch and black buckle, ensure the seat ...

  • Page 50

    Adjustable upper shoulder belt anchorage in the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that fits you best. As a guide, ...

  • Page 51

    Warning! • a lap belt worn too loose or too high is dangerous. • a belt worn too loose can allow you to slip down and under the belt in a collision. • a belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal inju...

  • Page 52

    Warning! • the belt and retractor assembly must be replaced if the seat belt assembly automatic locking re- tractor (alr) feature or any other seat belt func- tion is not working properly when checked ac- cording to the procedures in the service manual. • failure to replace the belt and retractor as...

  • Page 53

    2. Turn the ignition switch to the on/run position and wait for the seat belt reminder light to turn off. 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4. Turn off the engine...

  • Page 54

    Warning! Using a seat belt extender when not needed can increase the risk of injury in an accident. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Driver and r...

  • Page 55

    The advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the...

  • Page 56

    Advanced front airbag features the advanced front airbag system has multistage driver and front passenger (if equipped) airbags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint con- troller (orc). The first stage inflator is trigg...

  • Page 57

    Here are some simple steps you can take to minimize the risk of harm from a deploying airbag: children 12 years old and under should always ride buckled up in a rear seat. Warning! Infants in rear-facing child restraints should never ride in the front seat of a vehicle with a passenger advanced fron...

  • Page 58

    If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer center. Phone numbers are provided under ⬙if you need assistance ⬙. Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your s...

  • Page 59

    Vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, advanced front airbags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. Becaus...

  • Page 60

    Warning! Ignoring the airbag warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an...

  • Page 61

    • flash hazard lights as long as the battery has power or until the ignition key is turned off. • turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • unlock the doors automatically. If a deployment occurs the front airbags are designe...

  • Page 62

    Do not drive your vehicle after the airbags have de- ployed. If you are involved in another collision, the airbags will not be in place to protect you. Warning! Deployed airbags cannot protect you in another col- lision. Have the airbags replaced by an authorized dealer immediately. Also, have the o...

  • Page 63

    Warning! (continued) • do not attempt to modify any part of your airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any airbag system service. If your seat including your trim cover and cushion need...

  • Page 64

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 65

    Child restraints everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the united states and all canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children...

  • Page 66

    • safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and ⬙convertible⬙ child seats. Both types of child restraints are held in the...

  • Page 67

    Warning! • rearward-facing child seats must never be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • improper installation can lead to failure of an infant or child restraint. It could come loos...

  • Page 68

    • if the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating ...

  • Page 69

    • check belt fit periodically. A child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Lower anchors and tet...

  • Page 70

    Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt. They will also have tether straps...

  • Page 71

    We urge you to carefully follow the directions of the manufacturer when installing your child restraint. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector, and a means for adjusting the tension in the strap. Forward-facing t...

  • Page 72

    To install a child restraint, first, pull enough of the seat belt webbing from the retractor to route it through the belt path of the child restraint and slide the latch plate into the buckle. Next, extract all the seat belt webbing out of the retractor and then allow the belt to retract into the re...

  • Page 73

    Tether anchorage points at the right and center front seat (regular cab - all seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat. 2. Lift the cover (if so equipped...

  • Page 74

    Multiple child restraint installation sequence (crew cab — rear seats) crew cab 1. The tether straps loops are located between the rear glass and the rear seat. There is a tether strap loop located behind each seating position. You can gain access to the center seating position tether strap loop by ...

  • Page 75

    3. Pass each tether strap hook under the head restraint and through the loop of webbing behind the child seat. 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the anchor loop. 5. Place a child restraint on the center rear seat and adjust the tether strap so t...

  • Page 76

    Transporting pets airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in an accident. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat...

  • Page 77

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- o...

  • Page 78

    Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, ...

  • Page 79

    Floor mat safety information always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in o...

  • Page 80

    Warning! (continued) • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • if required, mounting posts must be properly installed, if not equipped...

  • Page 81: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 83 ▫ automatic dimming mirror — if equipped . . . 84 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 85...

  • Page 82

    ▫ things you should know about your uconnect™ phone . . . . . . . . . . . . . . . . . . . . . 111 ▫ general information . . . . . . . . . . . . . . . . . . 122 䡵 voice command — if equipped . . . . . . . . . . . 122 ▫ voice command system operation . . . . . . . . 122 ▫ commands . . . . . . . . . . ...

  • Page 83

    ▫ automatic headlights . . . . . . . . . . . . . . . . . 146 ▫ headlight delay . . . . . . . . . . . . . . . . . . . . . 147 ▫ parking lights and panel lights . . . . . . . . . 147 ▫ fog lights — if equipped . . . . . . . . . . . . . . 148 ▫ interior lights . . . . . . . . . . . . . . . . . . . . . ...

  • Page 84

    䡵 electrical power outlets . . . . . . . . . . . . . . . . . 163 䡵 cigar lighter and ash receiver — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 167 䡵 power inverter — if equipped . . . . . . . . . . . . 168 䡵 cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 170 ▫ fr...

  • Page 85

    Mirrors inside day/night mirror headlight glare can be reduced by moving the small control lever under the mirror to the night position (lever flipped toward the rear of vehicle). The mirror should be adjusted with the lever set in the day position (lever flipped toward the windshield). The mirror s...

  • Page 86

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 87

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they ...

  • Page 88

    Power mirrors — if equipped the controls for the power mirrors are located on the driver’s door trim panel. The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. Power mirror controls power mirror controls 1 — mirror select buttons 2 — mirror control 86 u...

  • Page 89

    To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Power folding outside mirrors — if equipped if equipped with power folding mirrors, they can...

  • Page 90

    The switch for the power folding mirrors is located between the power mirror switches l (left) and r (right). Press the switch once and the mirrors will fold in, pressing the switch a second time will return the mirrors to the normal driving position. Note: ten or more switch activations within one ...

  • Page 91

    Illuminated vanity mirror — if equipped illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on auto- matically. Closing the mirror cover turns off the light. “slide-on-rod” features of sun viso...

  • Page 92

    To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until the sun visor is in the desired position. Trailer towing mirrors — if equipped these mirrors are designed with an adjustable mirror head to provide a greater vision range...

  • Page 93

    Note: fold the trailer towing mirrors rearward prior to entering an automated car wash. A small blindspot mirror is located next to main mirror and can be adjusted separately. Uconnect™ phone — if equipped uconnect™ phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™...

  • Page 94

    • www.Jeep.Com/uconnect • or call 1–877–855–8400 uconnect™ phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The uconnect™ phone is driven through your bluetooth 威 “h...

  • Page 95

    Voice command button actual button location may vary with the ra- dio. The individual buttons are described in the “operation” section. The uconnect™ phone can be used with any hands-free profile certified bluetooth 威 mobile phone. See the uconnect™ website for supported phones. Refer to your mobile...

  • Page 96

    Example, you can use the compound form voice command “phonebook new entry”, or you can break the compound form command into two voice com- mands: “phonebook” and “new entry”. Please re- member, the uconnect™ phone works best when you talk in a normal conversational tone, as if speaking to someone si...

  • Page 97

    • when prompted, after the beep, say “pair a phone” and follow the audible prompts. • you will be asked to say a four-digit personal identi- fication number (pin), which you will later need to enter into your mobile phone. You can enter any four-digit pin. You will not need to remember this pin afte...

  • Page 98

    • the uconnect™ phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by saying a name • press the button to begin. • after the “ready” prompt and the following beep, say “call”. • the system will prompt you to say the name of the person you...

  • Page 99

    • when prompted, enter the number designation (e.G., “home”, “work”, “mobile”, or “other”). This will allow you to store multiple numbers for each phone- book entry, if desired. • when prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an ent...

  • Page 100

    • depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previously downloaded phonebook is avail- able for use. • only the phonebook of the currently connected mobile phone is accessible. • ...

  • Page 101

    First disconnect or drop the bluetooth 威 connection to the uconnect™ phone, and then send the address book entry via bluetooth 威. Please see your phone owner’s manual for specific instructions on how to drop the bluetooth 威 connection. • if the phonebook entry is longer than 24 characters, it will o...

  • Page 102

    Delete uconnect™ phonebook entry note: editing phonebook entries is recommended when the vehicle is not in motion. • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook delete”. • after you enter the phonebook delete menu, you will then be asked for the name ...

  • Page 103

    • note that only the phonebook in the current language is deleted. • automatic downloaded phonebook entries cannot be deleted or edited. List all names in the uconnect™ phonebook • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook list names”. • the uconnec...

  • Page 104

    Call, press and hold the button until you hear a single beep, indicating that the incoming call was rejected. Answer or reject an incoming call — call currently in progress if a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting th...

  • Page 105

    Conference call when two calls are in progress (one active and one on hold), press and hold the button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-way calling to initiate three-way calling, press the button while a call is in progress, ...

  • Page 106

    • after the ignition key is switched to off, a call can continue on the uconnect™ phone either until the call ends, or until the vehicle battery condition dictates cessation of the call on the uconnect™ phone and transfer of the call to the mobile phone. • after the ignition key is switched to off, ...

  • Page 107

    If the phone is not reachable and the uconnect™ phone is operational, you may reach the emergency number as follows: • press the button to begin. • after the ⬙ready⬙ prompt and the following beep, say “emergency” and the uconnect™ phone will instruct the paired mobile phone to call the emergency num...

  • Page 108

    • after the “ready” prompt and the following beep, say “towing assistance”. Note: • the towing assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the u.S., 1-877-213-4525 for canada, 55-14- 3454 for mexico city and 1-800-712-3040 for outside mexico c...

  • Page 109

    On your mobile phone keypad, you can press the button and say the sequence you wish to enter, followed by the word “send”. For example, if required to enter your pin followed with a pound, (3 7 4 6 #), you can press the button and say, “3 7 4 6 # send”. Saying a number, or sequence of numbers, follo...

  • Page 110

    • press the button to begin. • after the “ready” prompt and the following beep, say one of the following: − “setup confirmation prompts on” − “setup confirmation prompts off” phone and network status indicators if available on the radio and/or on a premium display such as the instrument panel cluste...

  • Page 111

    • following the beep, say “mute”. In order to un-mute the uconnect™ phone: • press the button. • following the beep, say “mute off”. Advanced phone connectivity transfer call to and from mobile phone the uconnect™ phone allows ongoing calls to be trans- ferred from your mobile phone to the uconnect™...

  • Page 112

    • the uconnect™ phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “select” or “delete”. Also, see the next two sec- tions for an alternate way to “select” or “...

  • Page 113

    Things you should know about your uconnect™ phone uconnect™ phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect™ tutorial.” voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect™ pho...

  • Page 114

    Voice command • for best performance, adjust the rearview mirror to provide at least 1 ⁄ 2 in (1 cm) gap between the overhead console (if equipped) and the mirror. • always wait for the beep before speaking. • speak normally, without pausing, just as you would speak to a person sitting a few feet/me...

  • Page 115

    • numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • you can say “o” (letter “o”) for “0” (zero). • even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • in a ...

  • Page 116

    Sms uconnect™ phone can read or send new messages on your phone. Read messages: if you receive a new text message while your phone is connected to uconnect™ phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • press the button. • ...

  • Page 117

    3. Where are you? 4. I need more direction. 5. L o l 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See you in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to c...

  • Page 118

    Bluetooth 威 communication link mobile phones have been found to lose connection to the uconnect™ phone. When this happens, the connection can generally be reestablished by switching the phone off/on. Your mobile phone is recommended to remain in bluetooth 威 on mode. Power-up after switching the igni...

  • Page 119

    3 understanding the features of your vehicle 117.

  • Page 120

    118 understanding the features of your vehicle.

  • Page 121

    3 understanding the features of your vehicle 119.

  • Page 122

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 120 unders...

  • Page 123

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 124

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 125

    Note: if you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system i...

  • Page 126

    Changing the volume 1. Start a dialogue by pressing the voice command button. 2. Say a command (e.G., “help”). 3. Use the on/off volume rotary knob to adjust the volume to a comfortable level while the voice command system is speaking. Please note the volume setting for voice command is different th...

  • Page 127

    • “next station” (to select the next station) • “previous station” (to select the previous station) • “menu radio” (to switch to the radio menu) • “main menu” (to switch to the main menu) satellite radio to switch to satellite radio mode, say “sat” or “satellite radio”. In this mode, you may say the...

  • Page 128

    • “new memo” (to record a new memo) — during the recording, you may press the voice command button to stop recording. You proceed by saying one of the following commands: − “save” (to save the memo) − “continue” (to continue recording) − “delete” (to delete the recording) • “play memos” (to play pre...

  • Page 129

    Note: keep in mind that you have to press the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect™ voice “voice training” feature may be u...

  • Page 130

    Manual seat adjuster — if equipped both front seats are independently adjustable forward or rearward and are equipped with a seatback recliner. The manual forward or rearward seat adjustment handle is found under the seat cushion at the front edge of each seat. Pull up on the handle and slide the se...

  • Page 131

    Warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Manual reclining seats — if equipped the recli...

  • Page 132

    Warning! • actuating the recliner handle will allow the seat- back to swing (dump) forward on manual recliner seats. Do not stand or lean in front of the seat while actuating the handle. The seatback may swing forward and hit you causing injury. This dump feature allows access to the storage bin beh...

  • Page 133

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be ...

  • Page 134

    Rear head restraints the outboard head restraints can be adjusted. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint. Note: the rear center head restr...

  • Page 135

    Adjusting the sear forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting the seat up or down the height of the seats...

  • Page 136

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seatbelts and while the vehicle is parked. Serious injury or death could ...

  • Page 137

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters in both the seat cushions and seatbacks. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- ha...

  • Page 138

    Caution! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. Front heated seats there are two heated seat switches that allow the driver and passenger to operate the seats independently. The controls for each seat are located near the bottom cen...

  • Page 139

    Before automatically shutting off. The heated seats can shut off early or may not turn on when the seat is already warm. Vehicle equipped with remote start on models that are equipped with remote start, the driver’s heated seat can be programmed to come on during a remote start. Refer to “remote sta...

  • Page 140

    Heat for a maximum of 60 minutes before switching to low heat. Once a seat has switched to the low heat setting it may operate for a maximum of 45 minutes before automatically shutting off. The heated seats can shut off early or may not turn on when the seat is already warm. Ventilated seats — if eq...

  • Page 141

    40-20-40 front bench seat — if equipped the seat is divided into three segments. The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped). Driver memory seat — if equi...

  • Page 142

    Keyless entry (rke) transmitters can also be pro- grammed to recall the same positions when the un- lock button is pressed. Note: the power lumbar option is not programmable with driver memory seats. Your vehicle was delivered with two rke transmitters. One or both rke transmitters can be linked to ...

  • Page 143

    7. Within five seconds, press and release memory button 1 or 2 on the driver’s seat. The next steps must be performed within 10 seconds if you desire to also use a rke transmitter to recall memory positions. 8. Turn the ignition off and remove the key. 9. Press and release the lock button on one of ...

  • Page 144

    Note: a chime sound may be heard if setting memory was inhibited for any reason. To disable a rke transmitter linked to memory 1. Turn the ignition switch to the off position and remove the key. 2. Press and release the memory set button located on the driver’s seat. 3. Within 10 seconds, press and ...

  • Page 145

    Driver easy exit and easy entry control this additional feature provides automatic driver’s seat positioning which will enhance driver mobility into and out of the vehicle. The seat cushion will move rearward approximately 2.5 in (60 mm) when the key is removed from the ignition switch. The seat wil...

  • Page 146

    2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, before raising the hood. Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latc...

  • Page 147

    Lights the headlight switch is located on the left side of the instrument panel, next to the steering wheel. The head- light switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped). Your vehicle is equipped with plastic head...

  • Page 148

    Headlights to turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the o (off) position. Autom...

  • Page 149

    Note: the engine must be running before the head- lights will turn on in the automatic mode. Headlight delay to aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for approximately 90 seconds. This delay is initiated when the ignition is turned off wh...

  • Page 150

    Fog lights — if equipped the fog lights are turned on by placing the headlight rotary control in the parking light or headlight position and pushing in the headlight rotary control. The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An ind...

  • Page 151

    The brightness of the instrument panel lighting can be regulated by rotating the dimmer control right (brighter) or left (dimmer). When the headlights are on you can supplement the brightness of the odometer, trip odom- eter, radio and overhead console by rotating the control to the right until you ...

  • Page 152

    Cargo light the cargo lights are turned on by pressing on the cargo button. The cargo lights will also turn on for approximately 30 seconds when a rke transmitter unlock button is pressed, as part of the illuminated entry feature. Lights-on reminder if the headlights, parking lights, or cargo lights...

  • Page 153

    Daytime running lights — if equipped the headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except park. This provides a constant ⬙lights on⬙ condition until the ignition is turned off. The lights illuminate at less than 50% of normal intensity....

  • Page 154

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Flash-to-pass you can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer-...

  • Page 155

    Intermittent wiper system the intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay inter...

  • Page 156

    To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Warning! Sudden loss of visibility through the windshield could lead ...

  • Page 157

    Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Release the lever to lock the steering column firmly in place. Warning! Do not adjust the steering column while driving. Adjusting the ...

  • Page 158

    The adjustable pedal switch is located to the left side of the steering column. • the pedals can be adjusted with the ignition off. • the pedals cannot be adjusted when the vehicle is in reverse or when the electronic speed control sys- tem is on. The following messages will be displayed on vehicles...

  • Page 159

    Heated steering wheel — if equipped the steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate for approximately 58 to 70 minutes before automa...

  • Page 160

    Warning! (continued) • do not place anything on the steering wheel that insulates against heat, such as a blanket or cush- ion. This may cause the steering wheel heater to overheat. Electronic speed control — if equipped when engaged, electronic speed control takes over the accelerator operation at ...

  • Page 161

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 162

    Deactivating electronic speed control a soft tap on the brake pedal or pulling the electronic speed control lever (cancel) toward you will deacti- vate the electronic speed control without erasing the set speed memory. Pushing the on/off button to the off position or turning off the ignition erases ...

  • Page 163

    To accelerate for passing press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Your vehicle may experience a d...

  • Page 164

    • power sliding rear window switch — if equipped courtesy/reading lights both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the u...

  • Page 165

    Note: the courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the ignition is turned off, they will extinguish after 15 minutes. Electrical power outlets the auxili...

  • Page 166

    Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this...

  • Page 167

    • inside the upper lid of the center storage compartment — if equipped. • rear of the center console storage compartment — crew cab. Power outlet — upper lid power outlet — rear center console 3 understanding the features of your vehicle 165.

  • Page 168

    The key symbol indicates that this outlet can supply power when the key is in the on or acc positions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge. Warning! To avoid serious injury or death: • only...

  • Page 169

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 170

    For vehicles equipped with a floor console the cuphold- ers may be used. Power inverter — if equipped a 115 volt (150 watts maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power device...

  • Page 171

    The power inverter switch is located on the switch bank below the climate controls. To turn on the power outlet, press the switch once. Press the switch a second time to turn the power outlet off. Note: • when the power inverter switch is pressed, there will be a delay of approximately one second be...

  • Page 172

    Cupholders front instrument panel cupholders — (40–20–40 seats) the cupholders are located in the pull-out tray on the center stack of the instrument panel. Front instrument panel cupholders — floor storage bin for vehicles equipped with bucket seats two cupholders are located in the floor storage b...

  • Page 173

    Rear cupholder — crew cab crew cab vehicles are equipped with rear cupholders located in the center armrest. Storage glove box storage the glove box is located on the passenger side of the instrument panel and features both an upper (if equipped) and lower storage area. Crew cab rear armrest cuphold...

  • Page 174

    To open the upper glove box push upward on the handle release. The glove box door will automatically open. To open the lower glove box, pull on the handle to release the latch and lower the door. Upper glove box lower glove box 172 understanding the features of your vehicle.

  • Page 175

    Door storage front door storage — if equipped storage areas and bottle holders (drivers side only) are located in the door trim panels. Rear door storage — crew cab storage compartments are located in both the driver and passenger door trim panels. Front door storage rear door storage 3 understandin...

  • Page 176

    Center storage compartment — if equipped the center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Warning! • this armrest is not a seat. Anyone seated on the armrest could be seri...

  • Page 177

    Pull on the upper handle on the front of the armrest to raise the cover. The upper storage area contains a 12 volt power outlet that can be used to power small electrical devices, refer to “electrical power outlets” for further information. With the upper lid closed, pull on the lower handle to open...

  • Page 178

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injur...

  • Page 179

    Storage and seats (crew cab) the crew cab models provide additional storage under the rear seats. Lift the seats to access the storage com- partment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Caution! Always lift the storage compartment lids by using ...

  • Page 180

    Plastic grocery bag retainers (regular cab models) retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the seats. Rear window features rear window defroster the rear window defroster button is located on the climate control panel. Press this bu...

  • Page 181

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 182

    Manual sliding rear window — if equipped a locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. 180 understanding the features of your vehicle.

  • Page 183: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 184 䡵 instrument cluster — base . . . . . . . . . . . . . . . 185 䡵 instrument cluster — premium . . . . . . . . . . . 186 䡵 instrument cluster descriptions . . . . . . . . . . . 187 䡵 electronic v...

  • Page 184

    ▫ operating instructions (voice command system) — if equipped . . . . . . . . . . . . . . . . 219 ▫ operating instructions (uconnect™ phone) — if equipped . . . . . . . . . . . . . . . . . . . . . . 219 䡵 media center 130 (sales code res) . . . . . . . . . 219 ▫ operating instructions — radio mode ....

  • Page 185

    ▫ system activation . . . . . . . . . . . . . . . . . . . . 250 ▫ electronic serial number/sirius identification number (esn/sid) . . . . . . . . . 250 ▫ selecting uconnect™ multimedia (satellite) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 ▫ satellite antenna . . . . . . . . ...

  • Page 186

    Instrument panel features 1 — headlight switch 7 — 115v power inverter outlet 13 — transfer case position switch 2 — instrument cluster 8 — power outlet 14 — ignition switch 3 — radio 9 — lower switch bank 15 — hood release 4 — upper switch bank 10 — cup holders 16 — parking brake release 5 — upper ...

  • Page 187

    Instrument cluster — base 4 understanding your instrument panel 185.

  • Page 188

    Instrument cluster — premium 186 understanding your instrument panel.

  • Page 189

    Instrument cluster descriptions 1. Tachometer the tachometer indicates engine speed in revolutions per minute (rpm x 1000). Caution! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur. 2. Turn signal indicators the arrow will flash with th...

  • Page 190

    Caution! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear cont...

  • Page 191

    Rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels. 7. Electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. The light will come on when the ignition is first t...

  • Page 192

    For vehicles equipped with a premium cluster this indi- cator will display in the electronic vehicle information center (evic). Refer to ”electronic vehicle information center (evic) — if equipped” for further information. 10. Tow/haul the tow haul button is located on the center stack switch bank. ...

  • Page 193

    Mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero. The two trip odometers show indi...

  • Page 194

    If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the odometer display area. Tighten the fuel filler cap properly and press the trip button to turn off the message. If the problem continues, the m...

  • Page 195

    2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. 15. Engine tem...

  • Page 196

    Lever to activate ers. Refer to “automatic transmission” in “starting and operating” for further information. 17. Low fuel light when the fuel level reaches approximately 3.0 gal (11.0 l) this light will turn on, and remain on until fuel is added. For vehicles equipped with a premium cluster this in...

  • Page 197

    20. Cargo light the cargo light will illuminate when the cargo light is activated by pressing the cargo light button on the headlight switch. 21. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it...

  • Page 198

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the abs, are also equipped with electronic brake force dist...

  • Page 199

    Center (evic). Refer to ”electronic vehicle information center (evic) — if equipped” for further information. 23. Malfunction indicator light (mil) the malfunction indicator light (mil) is part of an onboard diagnostic (obdii) system which monitors the emissions and engine control sys- tem. If the v...

  • Page 200

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to...

  • Page 201

    27. Transmission temperature warning light this light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation ...

  • Page 202

    28. Seat belt reminder light when the ignition switch is first turned to on/ run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s seat belt rema...

  • Page 203

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. Note: the compass on your vehicle is self-calibrating, eliminating the need to manually calibrate the compass...

  • Page 204

    • audio modes display steering wheel evic control button, as it appears on the left side of the steer- ing wheel. Press and release the up button to scroll up- ward through the main menus (dte, mi/gal, system info, messages, units, setup) and sub- menus. Press and release the down button to scroll d...

  • Page 205

    Electronic vehicle information center (evic) displays when the appropriate conditions exist, the evic displays the following messages: • left front turn signal lamp out • right front turn signal lamp out • left rear turn signal lamp out • right rear turn signal lamp out • service air filter • check ...

  • Page 206

    • turn signal on • rke battery low • low washer fluid • oil change due > dealer info • park assist on • park assist off • warning object detected • left front turn signal light out • left rear turn signal light out • right front turn signal light out • right rear turn signal light out • service park...

  • Page 207

    • memory system unavailable — seatbelt buckled • memory 1 profile recall • memory 2 profile recall • adjustable pedals unavailable — vehicle in reverse • adjustable pedals unavailable — cruise engaged • to tow vehicle safely, read neutral shift procedure in owners manual evic warning lights • door a...

  • Page 208

    • electronic speed control light this light will turn on when the electronic speed control is on. • electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. The light will come on when the ignition is first turned on and remain on...

  • Page 209

    If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into neutral and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if...

  • Page 210

    • loose gascap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap icon will display in the telltale display area. Tighten the fuel filler cap properly and press the select button to turn off the message. If the prob...

  • Page 211

    Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. Dte cannot be reset through the return b...

  • Page 212

    The trip functions mode displays the following informa- tion: • trip a shows the total distance traveled for trip a since the last reset. • trip b shows the total distance traveled for trip b since the last reset. • elapsed time shows the total elapsed time of travel since the last reset when the ig...

  • Page 213

    • trans temperature displays the actual transmission temperature. • engine hours displays the number of hours of engine operation. • trailer brake — if equipped displays trailer brake output power and trailer brake status indicator. Units press and release the up or down button until “units” display...

  • Page 214

    Temperature sensor caused by the snowplow. In addi- tion, on vehicles equipped with automatic tempera- ture control (atc), it is suggested that the interior cabin temperature be manually controlled should the system not perform as desired while in automatic mode. Both the outside temperature display...

  • Page 215

    5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “cal” indicator turns off. The compass will now function normally. Compass variance compass variance is the difference between magnetic north and geographic north. To compensate for the differen...

  • Page 216

    3. Press the down button until the “compass variance” message is displayed in the evic, then press the select button. The last variance zone number displays in the evic. 4. Press and release the select button until the proper variance zone is selected, according to the map. 5. Press and release the ...

  • Page 217

    The feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Auto lock doors when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press and release t...

  • Page 218

    When the remote keyless entry (rke) transmitter un- lock button is pressed. If this feature is not selected then the memory seat, mirror, and radio settings can only return to the memory set position using the seat mounted switch. To make your selection, press and release the select button until a c...

  • Page 219

    Headlamp off delay when this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the select button until a check...

  • Page 220

    Easy exit seat — if equipped this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated or t...

  • Page 221

    Calibrate compass refer to “compass display” for more information. Media center 730n/430/430n (rhr/rer/rbz/ rhb) cd/dvd/hdd/nav — if equipped note: the sales code is located on the lower right side of the unit’s faceplate. Refer to your uconnect™ multimedia rhr, rer, rbz or rhb user’s manual for det...

  • Page 222

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 223

    4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the ...

  • Page 224

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button press the buttons to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button...

  • Page 225

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 226

    Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 227

    Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek button to move to the next ran- domly selected track. Press the ...

  • Page 228

    Exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a three- character extension) • level 2: 31 (including a separator ⬙.⬙ and a three- c...

  • Page 229

    Mpeg specification sampling frequency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and alb...

  • Page 230

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the dis...

  • Page 231

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 232

    Phone button uconnect™ phone — if equipped press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in “under- standing the features if your vehicle”. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with...

  • Page 233

    Info button press the info button for an rds station (one with call letters displayed). The radio will return a radio text message broadcast from an fm station (fm mode only). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the directi...

  • Page 234

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program for...

  • Page 235

    Program type 16-digit character display soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type...

  • Page 236

    Not selected within five seconds after pressing the set/ rnd button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will sh...

  • Page 237

    Radio display. If a cd does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded. If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the d...

  • Page 238

    Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pressing and holding the seek ...

  • Page 239

    Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded using formats other than iso 9660 level 1 and level 2, the radio may fail to read files properly and may be unable to play...

  • Page 240

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 241

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 242

    Press and hold the info button again for three seconds to return to ⬙elapsed time⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or cassette player and utilize the vehicle’s au...

  • Page 243

    Radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www- .Siriuscanada.Ca for ...

  • Page 244

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 245

    Additional three seconds will make the radio display the song title all of the time (press and hold again to return to normal display). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) tu...

  • Page 246

    Set button – to set the pushbutton memory when you are receiving a channel that you wish to commit to pushbutton memory, press the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a butt...

  • Page 247

    This feature allows an ipod 威 to be plugged into the vehicle’s sound system through a 16–pin connector, using the provided interface cable. Ipod 威 control supports mini, 4g, photo, nano, 5g ipod威 and iphone 威 devices. Some ipod威 software versions may not fully support the ipod 威 control features. Pl...

  • Page 248

    • the ipod威 audio can be played on the vehicle’s sound system, providing metadata (artist, track title, album, etc.) information on the radio display. • the ipod威 can be controlled using the radio buttons to play, browse, and list the ipod 威 contents. • the ipod威 battery charges when plugged into th...

  • Page 249

    • jump backward in the current track by pressing and holding the rw button. Holding the rw button long enough will jump to the beginning of the current track. • jump forward in the current track by pressing and holding the ff >> button. • a single press backward rw or forward ff >> will jump backwar...

  • Page 250

    Shuffle off modes for the ipod 威. If the rnd icon is showing on the radio display, then the shuffle mode is on. List or browse mode during play mode, pressing any of the buttons described below, will bring up list mode. List mode enables scrolling through the list of menus and tracks on the ipod 威. ...

  • Page 251

    • pressing a preset button will display the current list on the top line and the first item in that list on the second line. • to exit list mode without selecting a track, press the same preset button again to go back to play mode . • list button: the list button will display the top level menu of t...

  • Page 252

    Uconnect™ multimedia (satellite radio) — if equipped (ren/rer/res radios only) satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is sirius satellite radio. This service offers over 130 channel...

  • Page 253

    Sirius id number will display. The sirius id number display will time out in two minutes. Press any button on the radio to exit this screen. Esn/sid access with ren/rer radios while in sat mode, press the menu button on the radio faceplate. Next, touch the subscription tab on the touch screen. All t...

  • Page 254

    Operating instructions - uconnect™ multimedia (satellite) mode note: the ignition switch must be in the on or acc position to operate the radio. Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch to ...

  • Page 255

    Or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Toggle the music type button again to select the music type. By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same ...

  • Page 256

    Pushbutton memory. The channels stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the channels that you commit to pushbutton memory (12 satellite stati...

  • Page 257

    The button located in the center of the right hand control will switch modes to radio, cd or other valid audio source. The left hand control is a rocker type switch with a pushbutton in the center. The function of the left hand control is different depending on which mode you are in. The following d...

  • Page 258

    2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not...

  • Page 259

    Higher temperatures than the outside ambient tempera- ture. The higher displayed temperature is due to blocked or reduced airflow to the underhood ambient tempera- ture sensor caused by the snowplow. In addition, on vehicles equipped with automatic temperature control (atc), it is suggested that the...

  • Page 260

    Front blower control there are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position. Note: for vehicles equipped with remote start, the climate controls ...

  • Page 261

    Panel mode air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-level mode air is directed through the panel and floor outlets. Note: there is a difference in temperature (in any conditions other than full cold or full hot), between the upp...

  • Page 262

    Recirculation control press this button to choose between outside air intake or recirculation of the air inside the vehicle. A led will illuminate when you are in recircula- tion mode. Only use the recirculation mode to temporarily block out any outside odors, smoke, or dust, and to cool the interio...

  • Page 263

    Economy mode if economy mode is desired, press the a/c button to turn off the led indicator and the a/c compressor. Rotate the temperature control knob to the desired temperature. Air conditioning operation push this button to engage the air conditioning (a/c). A led will illu- minate when the a/c s...

  • Page 264

    • when occupants in the vehicle select an auto mode operation, auto blower operation is set by using rotary knobs on the control unit and a comfort temperature setting by using the temperature up and down but- tons. • the system provides set-and-forget operation for op- timum comfort and convenience...

  • Page 265

    Automatic operation 1. Position the mode control knob to the auto position on the automatic temperature control (atc) panel. 2. Position the blower control knob in the auto posi- tion on the atc panel. 3. Next, adjust the temperature you would like the system to maintain by adjusting the driver and ...

  • Page 266

    Manual operation this system offers a full complement of manual override features. Note: each of these features operate independently from each other. If any one feature is controlled manually, the temperature doors will continue to operate automati- cally. There are six fixed blower speeds. Use thi...

  • Page 267

    Floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix mode air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while k...

  • Page 268

    Recirculation mode should only be used temporarily. The recirculation led will illuminate on the blower control knob when this button is selected. Push the button a second time to turn off the recirculation mode led and allow outside air into the vehicle. Note: in cold weather, use of recirculation ...

  • Page 269

    Vacation/storage any time you store your vehicle or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in fresh air with the blower setting in high. This will ensure adequate system lubrication to minimize the possibility of ...

  • Page 270

    Operating tips 268 understanding your instrument panel.

  • Page 271: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 273 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 273 ▫ automatic transmission . . . . . . . . . . . . . . . 273 ▫ extreme cold weather (below –20°f or ⫺29°c) . . . . . . . . . . . . . . . 274...

  • Page 272

    ▫ transfer case position indicator light . . . . . . 287 ▫ electronically shifted transfer case (four-position switch) – if equipped . . . . . . . 288 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . 292 䡵 limited-slip differential . . . . . . . . . . . . . . . . . 294 䡵 driving on slipper...

  • Page 273

    ▫ spare tire matching original equipped tire and wheel – if equipped . . . . . . . . . . . . . . 320 ▫ compact spare tire – if equipped . . . . . . . . 321 ▫ full size spare – if equipped . . . . . . . . . . . . 322 ▫ limited-use spare – if equipped . . . . . . . . . 322 ▫ tire spinning . . . . . . ...

  • Page 274

    䡵 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . 340 ▫ common towing definitions . . . . . . . . . . . . 340 ▫ trailer hitch classification . . . . . . . . . . . . . . 343 ▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . 344 ▫ trailer and tongue weight . . . ...

  • Page 275

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Warnin...

  • Page 276

    Extreme cold weather (below –20°f or ⫺29°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If engine fails to start if the engine fails to start after you have followed the “normal...

  • Page 277

    If the engine has been flooded, it may start to run, but not have enough power to continue running when the key fob is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key fob once the engine is running smoo...

  • Page 278

    Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle spee...

  • Page 279

    Warning! (continued) • unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into park, remove the key fob from the ignition, a...

  • Page 280

    Five–speed automatic transmission (545rfe) — 5.7l engine only the shift lever display located in the instrument panel cluster indicates the transmission gear range. The shift lever is mounted either on the right side of the steering column (if equipped) or on the floor console (if equipped). You mus...

  • Page 281

    Accelerations. This additional gear improves vehicle perfor- mance and cooling capability when towing a trailer on certain grades. In ers mode, first through third gear are underdrive gears, and fourth gear is direct drive. Ers fifth gear (overdrive) is the same as the normal fourth gear. When in th...

  • Page 282

    Gear ranges do not race the engine when shifting from park or neutral position into another gear range. Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use park while the vehicle is in motion. Apply the parking brake when leav...

  • Page 283

    Neutral this range is for when the vehicle is standing for pro- longed periods with the engine running. The engine may be started in this range. Set the parking brake and shift the transmission into park if you must leave the vehicle. Drive this range provides all forward gears, including third gear...

  • Page 284

    Temperature warning light” may illuminate and the transmission may downshift out of overdrive until the transmission cools down. After cool down, the transmis- sion will resume normal operation. The transmission will downshift from overdrive to drive if the accelerator pedal is fully pressed at vehi...

  • Page 285

    The “tow/haul indicator light” will illuminate in the instrument cluster to indicate when the switch has been activated. Pressing the switch a second time restores normal operation. If the “tow/haul” mode is desired, the button must be pressed each time the engine is started. Torque converter clutch...

  • Page 286

    Four-wheel drive operation — if equipped four-wheel drive trucks are equipped with either a manually shifted transfer case or an electronically shifted transfer case. Refer to the operating instructions for your transfer case, located in this section for further informa- tion. Manually shifted trans...

  • Page 287

    When operating your vehicle in 4l, the engine speed is approximately three times that of the 2h or 4h positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circ...

  • Page 288

    For additional information on the appropriate use of each transfer case mode position, see the information below: 2h rear-wheel drive high range - this range is for normal street and highway driving on dry hard surfaced roads. 4h four-wheel drive high range - this range locks the front and rear driv...

  • Page 289

    2h or 4h ⇔ 4l with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift the transmission into neutral. While the vehicle is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position. Do not pause in transfer case neutral. Note: • pausing in transfer case ne...

  • Page 290

    Electronically shifted transfer case (four-position switch) – if equipped this is an electronic shift transfer case and is operated by the 4wd control switch (transfer case switch), which is located on the instrument panel. This electronically shifted transfer case provides four mode positions: • tw...

  • Page 291

    Desired position. Refer to “shifting procedure” for spe- cific shifting instructions. The 4wd lock and 4wd low positions are designed for loose, slippery road surfaces only. Driving in the 4wd lock and 4wd low positions on dry hard surfaced roads may cause in- creased tire wear and damage to the dri...

  • Page 292

    Note: before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob back to the current position, wait five seconds, and retry selection. To find the shift require- ments, refer to...

  • Page 293

    Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the drivetrain. Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do ...

  • Page 294

    N neutral - this range disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “recreational towing” in starting and operating” for further information. Shifting procedure note: • if any of the requirements to select a new trans...

  • Page 295

    Note: the four-wheel drive system will not allow shifts between 2wd/4wd lock if the front and/or rear wheels are spinning (no traction). In this situation, the selected position indicator light will flash and the origi- nal position indicator light will remain on. At this time, reduce speed and stop...

  • Page 296

    Note: • if steps 1 or 2 of either the preferred or alternate procedure are not satisfied prior to attempting the shift, then the desired position indicator light will flash continuously while the original position indicator light is on, until all requirements have been met. • the ignition switch mus...

  • Page 297

    Warning! On vehicles equipped with a limited-slip differential never run the engine with one rear wheel off the ground since the vehicle may drive through the rear wheel remaining on the ground. You could lose control of the vehicle. Care should be taken to avoid sudden accelerations when both rear ...

  • Page 298

    Traction when driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precau- tions shoul...

  • Page 299

    Shallow standing water although your vehicle is capable of driving through shallow standing water, consider the following caution and warning before doing so. Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the...

  • Page 300

    Warning! • driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • driving through standing water limits your vehi- cle’s braking capabilities, which increases stop- ping distances. Therefore, after driving thr...

  • Page 301

    • upon initial start-up in cold weather, the power steer- ing pump may make noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system. Warning! Continued operation with ...

  • Page 302

    Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid. If necessary, add fluid to restore to the proper indicated leve...

  • Page 303

    When the parking brake is applied with the ignition switch on, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime ...

  • Page 304

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic transmission in park, a manual transmission in reverse or first gear. Failure to do so may cause the vehicle to roll and cause dam...

  • Page 305

    Four-wheel anti-lock brake system warning! The four-wheel anti-lock brake system contains sophisticated electronic equipment. It may be sus- ceptible to interference caused by improperly in- stalled or high output radio transmitting equipment. This interference can cause possible loss of anti-lock b...

  • Page 306

    Abs warning light the abs includes an amber warning light. When the light is illuminated, the abs is not functioning. The system reverts to standard, non-anti-lock brakes. Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stop...

  • Page 307

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 308

    Tires designed to this standard have the letter “t” molded into the sidewall preceding the size designa- tion. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing ...

  • Page 309

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 310

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 311

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire pressure cold tire inflation pressure is defined as the tire pressure after ...

  • Page 312

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total wei...

  • Page 313

    3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to th...

  • Page 314

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 315

    5 starting and operating 313.

  • Page 316

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 317

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 318

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire infl...

  • Page 319

    Tire inflation pressure – 4500/5500 with steel carcass ply tires this type of tire utilizes steel cords in the sidewall. As such, they cannot be treated like normal light truck tires. Adjusting tire pressure must be performed by personnel trained, supervised and equipped accordingly. Inflation press...

  • Page 320

    4500/5500 tire inflation 318 starting and operating.

  • Page 321

    When adjusting inflation pressure to a tire and wheel assembly mounted on a vehicle, use a remote mount automatic inflation kit or see your authorized dealer. Note: never attempt to re-inflate a tire and wheel assembly which has been run flat or is extremely under- inflated without first removing th...

  • Page 322

    Radial ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision result- ing in serious injury or death. Always use radial ply tires in sets of four (or six, in case of trucks with dual re...

  • Page 323

    Caution! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a compact, full size or limited-use temporary spare installed. Damage to the vehicle may result. Compact spare tire – if equipped the compact spare is for temporary emergency use only. You c...

  • Page 324

    Full size spare – if equipped the full size spare is for temporary emergency use only. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the te...

  • Page 325

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Wa...

  • Page 326

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point. Life of tire the ...

  • Page 327

    Information” placard for the size designation of your tire. The load index and speed symbol for your tire will be found on the original equipment tire sidewall. See the tire sizing chart example found in the tire safety information section of this manual for more information relating to the load ind...

  • Page 328

    Warning! (continued) • never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision result- ing in serious injury or de...

  • Page 329

    Caution! (continued) • because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Bro- ken chains can cause serious vehicle damage. Stop the vehicle immediately if noise occurs that could suggest chain breakage. Remo...

  • Page 330

    • on 4x2 vehicles, class “u” snow chains are permitted on the rear wheels only of vehicles equipped with lt245/70r17, lt265/70r17, and lt235/80r17 size tires. • on 4x4 single rear wheel (srw) vehicles, class “u” snow chains are permitted on the rear wheels only on vehicles equipped with lt265/70r17....

  • Page 331

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Tire rotation recommendations tires on the fr...

  • Page 332

    Note: on canadian vehicles only, if your vehicle is equipped with all-season type tires on the front and on/off road type tires mounted on the rear, do not use a front to back rotation pattern. Instead, rotate your tires side to side at the recommended intervals. Dual rear wheels the tires used on d...

  • Page 333

    Caution! 4500/5500 dual rear tires have only one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the on/off road tire. • when replacing a flat, the spare tire may have to be remounted on the rim or installed at a different location to maintain the co...

  • Page 334

    Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) to define fuel properties necessary to deliver enhanced emissions, performance and durability for your vehicle. We recommend the use of gasolines that meet the wwfc s...

  • Page 335

    E-85 usage in non-flex fuel vehicles non-ffv vehicles are compatible with gasoline contain- ing 10% ethanol (e10). Gasoline with higher ethanol content may void the vehicle’s warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • ...

  • Page 336

    Allowed in the united states. Mmt is prohibited in federal and california reformulated gasoline. Materials added to fuel all gasolines sold in the united states are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal condition...

  • Page 337

    Caution! (continued) • the use of fuel additives which are now being sold as octane enhancers is not recommended. Many of these products contain high concentra- tions of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsi...

  • Page 338

    Warning! (continued) • guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel the fuel tank filler tube has a rest...

  • Page 339

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel to the vehicle when the engine is running. This is in violation of most state and federal fire regulations and may cause the mil to turn on. Note: tighten ...

  • Page 340

    Vehicle loading certification label as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle w...

  • Page 341

    Tire size the tire size on the label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim size this is the rim size that is appropriate for the tire size listed. Inflation pressure this is the cold tire inflation pressure for yo...

  • Page 342

    Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way you...

  • Page 343

    The recommended way to measure gtw is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Note: t...

  • Page 344

    That typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connec...

  • Page 345

    Fifth-wheel hitch the fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. It connects a vehicle and fifth-wheel trailer with a coupling king pin. Gooseneck hitch the gooseneck hitch employs a pivoted coupling arm which atta...

  • Page 346

    All trailer hitches should be professionally installed on your vehicle. Trailer towing weights (maximum trailer weight ratings) note: for additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http://www.Ramtrucks.Com. • http://www.Dodge....

  • Page 347

    • the weight of any other type of cargo or equipment put in or on your vehicle • the weight of the driver and all passengers. Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be con...

  • Page 348

    Warning! (continued) • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision. •...

  • Page 349

    Warning! (continued) 4. Trailer tongue weight rating for the trailer hitch utilized (this requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing requirements – tires • do not attempt to tow a trailer while using a co...

  • Page 350

    • an electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • trailer brakes are recommended for trailers over...

  • Page 351

    Note: this module has been designed and verified for electric trailer brakes. To determine the type of brakes on your trailer, check with your trailer manufacturer or dealer. The user interface consists of the following: gain/ brake output power display shows the current gain setting. This display m...

  • Page 352

    Lever is activated while the brake is also applied, the greater of the two inputs determines the power sent to the trailer brakes. The trailer and the vehicle’s brake lamps will come on when either vehicle braking or manual trailer brakes are applied. Trailer brake status indicator light this light ...

  • Page 353

    1. Make sure the trailer brakes are in good working condition, functioning normally, and properly adjusted. See your trailer dealer if necessary. 2. Hook up the trailer and make the electrical connec- tions according to the trailer manufacturer’s instructions. 3. When a trailer with electric brakes ...

  • Page 354

    Caution! The itbm module has been designed and verified for electric trailer brakes. Connecting a trailer that is not compatible with the itbm system may result in reduced or complete loss of trailer braking. There may be a increase in stopping distance or trailer instability which could result in d...

  • Page 355

    Warning! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automo- tive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. Towing tips before setting out on a trip, practice turni...

  • Page 356

    Electronic speed control – if equipped − do not use in hilly terrain or with heavy loads. − when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − use speed control in flat terrain and with light loads to maxim...

  • Page 357

    Warning! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in a collision. Do not expect that the airbag will perform as de- scribed earlier in this manual caution! The “lamp out” indicator could illuminate if exte- rior lamps are not properly installed. Be...

  • Page 358

    The loaded vehicle weight, including the snowplow system, all aftermarket accessories, driver, passengers, options, and cargo, must not exceed either the gross vehicle weight (gvwr) or gross axle weight (gawr) ratings. These weights are specified on the safety com- pliance certification label on the...

  • Page 359

    Note: during snowplow usage on vehicles equipped with outside temperature display, the display may show higher temperatures than the outside ambient tempera- ture. The higher displayed temperature is due to blocked or reduced airflow to the underhood ambient tempera- ture sensor caused by the snowpl...

  • Page 360

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models flat tow none not allowed see instructions • automatic transmission in park • manual transmission in gear (not in neutral (n) ...

  • Page 361

    This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure: 1. Properly secure the dolly to the tow vehicle, following the dolly manufacturer’s instructions. 2. Drive the rear wheels onto the tow dolly. 3. Firmly set the parking brake. Place automatic ...

  • Page 362

    Caution! • front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. • tow only in the forward direction. Towing this vehicle backwards can cause severe damage to the transfer case. • ...

  • Page 363

    Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engaging the parking brake. The transfer case neutral (n) position disengages both the front and rear driveshafts from the powertrain and will allow the ...

  • Page 364

    12. Shift the transmission into park or place manual transmission in gear (not in neutral). Caution! Damage to the transmission may occur if the trans- mission is shifted into park with the transfer case in neutral (n) and the engine running. With the trans- fer case in neutral (n) ensure that the e...

  • Page 365

    7. Shift the automatic transmission into park, or place manual transmission in neutral. 8. Release the brake pedal. 9. Disconnect vehicle from the tow vehicle. 10. Start the engine. 11. Press and hold the brake pedal. 12. Release the parking brake. 13. Shift the transmission into gear, release the b...

  • Page 366

    1. Bring the vehicle to a complete stop. Shift automatic transmission into park. 2. Turn off the engine. 3. Turn the ignition switch to the on/run position, but do not start the engine. 4. Press and hold the brake pedal. 5. Shift the automatic transmission into neutral or press the clutch pedal on a...

  • Page 367

    Caution! Damage to the transmission may occur if the trans- mission is shifted into park with the transfer case in neutral and the engine running. With the transfer case in neutral, ensure that the engine is off prior to shifting the transmission into park. 15. Remove the key fob from the ignition s...

  • Page 368

    1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake. 3. Insert the key fob into the ignition switch and turn it to the on/run position, but do not start the engine. 4. Press and hold the brake pedal. 5. Shift the transmission into neu...

  • Page 369

    And must continue to be met until the shift has been completed. If any of these requirements are not met prior to pressing the neutral button, or are no longer met during the shift, the neutral indicator light will flash continuously until all requirements are met or until the neutral button is rele...

  • Page 371: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 370 䡵 jacking and tire changing . . . . . . . . . . . . . . . 370 ▫ 3500 models — if equipped . . . . . . . . . . . . . 371 ▫ preparations for jacking . . . . . . . . . . . . . . . 372 ▫ jacking instructions...

  • Page 372

    Hazard warning flashers the hazard warning flasher switch is located on the upper switch bank just below the radio. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press...

  • Page 373

    Warning! (continued) • the jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. 3500 models — if equipped the jack and jack tools are st...

  • Page 374

    Warning! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious i...

  • Page 375

    6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jacking instructions instructions warning! Ca...

  • Page 376

    Warning! (continued) • if working on or near a roadway, be extremely careful of motor traffic. • to assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. Caution! Do not attempt to raise the vehicle by jacking on locations other ...

  • Page 377

    When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Securely place the jack under the sway bar bracket (unless both tires are flat on one side, then place jack under shock bracket) facing forward in vehicle. Connect the jack tube ext...

  • Page 378

    4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. Warning! Raising the vehicle higher than necessary can make the vehicle unstable and cause a collision. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove t...

  • Page 379

    8. Lower the jack to its fully closed position. If the jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. Stow the replaced tire, jack, and tools as previously described. 9. Adjust the tire pressure when possible. ...

  • Page 380

    On 3500 models with dual rear wheels (drw), you must first remove the hub caps. The jack handle driver has a hook at one end that will fit in the pry off notch of the rear hub caps. Position the hook and pull out on the ratchet firmly. The hub cap should pop off. The wheel skins can now be removed. ...

  • Page 381

    Dual rear wheels dual wheels are flat mounted, center piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer. Slots in the wheels will assist in properly orienting the...

  • Page 382

    These dual rear wheels should be tightened as follows: 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a tightening pattern (8 studs) tightening pattern (10 studs) 380 what ...

  • Page 383

    Second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). It is recommended that wheel stud nuts be kept torqued to specifications at all times. Torque wheel stud nuts to specifications at each lubrication interval. ...

  • Page 384

    Hoisting a conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking loca- tions. However, a floor jack or frame hoist must never be used on any other parts of the underbody. Caution! Never use a floor jack directly under the differential housing of a load...

  • Page 385

    Note: the positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan bla...

  • Page 386

    3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-start...

  • Page 387

    Warning! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then st...

  • Page 388

    Freeing a stuck vehicle if the vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the shift lever rhythmically between drive and reverse while ap- plying slight pressure to the accelerator. Caution! • racing the engine or spinning the wheels may lead to tran...

  • Page 389

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 390

    Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use the following procedure to temporarily move the shift lever: 1. Firmly set the parking brake. 2. Turn the ignition switch to the on/run position without starting the engine. 3. Tilt...

  • Page 391

    Towing a disabled vehicle proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to...

  • Page 392

    Caution! Towing faster than 30 mph (50 km/h) or for more than 15 miles (25 km) can cause severe damage to the transmission. Such damage is not covered by the new vehicle limited warranty. If the vehicle is to be towed faster than 30 mph (50 km/h) or more than 15 miles (25 km) the vehicle must be tow...

  • Page 393: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 5.7l . . . . . . . . . . . . . 393 䡵 onboard diagnostic system (obd ii) . . . . . . . 394 ▫ loose fuel filler cap message . . . . . . . . . . . 394 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 394

    ▫ exhaust system . . . . . . . . . . . . . . . . . . . . . 406 ▫ cooling system . . . . . . . . . . . . . . . . . . . . . 409 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 415 ▫ rear axle and 4x4 front driving axle fluid level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 395

    Engine compartment — 5.7l 1 — air cleaner filter 7 — washer fluid reservoir 2 — automatic transmission dipstick 8 — integrated power module (fuses) 3 — engine oil fill 9 — power steering fluid reservoir 4 — engine oil dipstick 10 — coolant pressure cap 5 — brake fluid reservoir 11 — engine coolant r...

  • Page 396

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 397

    The select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). Emissions inspection and maintenance programs in some l...

  • Page 398

    4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 399

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 400

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 401

    Caution! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could damage your engine. Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” ...

  • Page 402

    Engine oil viscosity (sae grade) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil fi...

  • Page 403

    Engine oil filter selection the manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high- quality filters should be used to assure most efficient service. Mopar 威 engine oil filters are a hig...

  • Page 404

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 405

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and are identified on the battery case. Cable clamps should b...

  • Page 406

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 407

    Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubri- cated periodically with a lithium based grease, such as mopar 威 spray white lube or equivalent, to assure qu...

  • Page 408

    Present please proceed to clean wiper blades with humid cloth removing any debris that may be affecting its function. Adding washer fluid the fluid reservoir is located under the hood and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (...

  • Page 409

    If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriora...

  • Page 410

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions con- trol device and may seriously reduce engine per- formance and cause serious damage to the engine. • damage to the catalytic converter can r...

  • Page 411

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 412

    Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper va...

  • Page 413

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they may not be compatible with the engine coolant (antifreeze) and may plug the radiator. • this vehicle has not been designed for us...

  • Page 414

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze...

  • Page 415

    Disposal of used coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children do not store ethylene glycol-based e...

  • Page 416

    2. Lift and remove the plastic dipstick from the reservoir neck. 3. Check the coolant level on the dipstick. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing en- gine coolant (antif...

  • Page 417

    • do not overfill the coolant recovery bottle. • check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing. • if frequent engine cool...

  • Page 418

    Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 419

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid ...

  • Page 420

    Warning! (continued) • do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Rear axle and 4x4 front driving axle fluid level for models with 9.25 in front axles and 11...

  • Page 421

    Refer to the “maintenance schedule” for the proper maintenance intervals. Lubricant selection refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Note: the presence of water in the gear lubricant will result in corrosion and possible failure of dif...

  • Page 422

    Automatic transmission selection of lubricant it is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only the manufacturer’s recommended trans- mission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicl...

  • Page 423

    Fluid level check if equipped with a dipstick, use the following procedure. If your vehicle has a capped dipstick tube, it is sealed and should not be tampered with. Your authorized dealer has the proper tools to ensure that the fluid level is set properly. The fluid level should be checked when the...

  • Page 424

    6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “hot” (upper) reference holes on the dipstick at normal operat- ing temperature. Verify that solid coating of oil is seen on both sides of the dipstick. If the fluid is low, add as required int...

  • Page 425

    Note: if the transmission is disassembled for any reason, the fluid and filter(s) should be changed. It is important that proper lubricant is used in the transmission. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Appearance care and protecti...

  • Page 426

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar 威 car wash or equiva- lent, or a mild car wash soap and rinse the panels completely with clear water. • if insects, tar or other similar deposits have accumu- lated on your vehicle, use mopar 威 super kleen bug...

  • Page 427

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause which destroys the paint and protective coating, have your vehicle repaired a...

  • Page 428

    • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar威 total clean or equivalent, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar威 multi-purpose cleaner or equivalent to a...

  • Page 429

    Cleaning headlights your vehicle is equipped with plastic headlights and fog lights (if equipped) that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize...

  • Page 430

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Dry ...

  • Page 431

    Cavity cartridge fuse mini fuse description j03 25 amp natural bat – passenger door node j04 40 amp green bat – abs pump j05 30 amp pink bat – abs valve j06 30 amp pink bat – h/lamp wash/mtv/ cm2200/elec vac pump j07 25 amp natural bat – driver door node j08 30 amp pink bat – dtcm/axle locks j09 30 ...

  • Page 432

    Cavity cartridge fuse mini fuse description m18 25 amp natural tcm/trans range m19 5 amp tan ign r/acc – sunroof/window sw illum m20 25 amp natural frt wiper m21 25 amp natural door locks m22 20 amp yellow fuel pump m23 20 amp yellow bat – trlr light/ pre-safe #2 m24 20 amp yellow bat – trlr tow bux...

  • Page 433

    Cavity cartridge fuse mini fuse description m34 15 amp blue bat – ccn/interior light/scm/sw bank m35 20 amp yellow htd seat/htd str wheel/rear htd seat m36 20 amp yellow ign r-rear seat/ steer wheel m37 10 amp red horn #1 m38 20 amp yellow iod-ccn/interior mods m39 30 amp green iod-amp/radio m40 25 ...

  • Page 434

    Cavity cartridge fuse mini fuse description m48 20 amp yellow ign r/acc-pwr outlet #2 m49 20 amp yellow ign r/acc/bat- pwr outlet #3 m50 25 amp natural asd #1, #2 m51 20 amp yellow asd #3 m52 10 amp red ign r/s-sway/ tcase/dtcm/ fad/trlr brake mod. M53 15 amp blue ign r/s-mfsw/ cnn/scm/ tpm/rr view ...

  • Page 435

    Vehicle storage if you are storing your vehicle for more than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • disconnect the ignition-off draw (iod) fuse located in the integrated power module, located in the engine compartment. The iod ca...

  • Page 436

    Replacement bulbs light bulbs – interior bulb no. Overhead console lamps . . . . . . . . . . . . . . . Ts 212-2 dome lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 7679 note: for lighted switches, see your authorized dealer for replacement instructions. All of the inside bulbs are brass ...

  • Page 437

    6. Remove the two headlamp assembly attachment screws. 7. Reach into the front wheel house ahead of the front wheel, remove the fastener, and lift the cover over the access hole in the front of the wheel house splash shield. Access to the rear of the lamp can be gained through this access hole. 8. R...

  • Page 438

    10. Disconnect electrical connectors. 11. Replace bulb(s) as necessary. Caution! • do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • always use the correct bulb size and type for replacement. An inc...

  • Page 439

    Center high-mounted stoplamp (chmsl) with cargo lamp 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn the desired bulb socket 1 ⁄ 4 turn and remove the socket and bulb from housing. 7 maint...

  • Page 440

    4. Pull the desired bulb straight from the socket. Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • outside bulbs: cargo lamps • inside bulb: center high-mounted stop lamp 5. Reverse the p...

  • Page 441

    Cab top clearance lamps – if equipped 1. Remove the two screws from the top of the lamp. 2. Rotate the socket 1 ⁄ 4 turn and pull it from the lamp assembly. 7 maintaining your vehicle 439.

  • Page 442

    3. Pull the bulb straight from it’s socket and replace. 440 maintaining your vehicle.

  • Page 443

    Fluid capacities u.S. Metric fuel (approximate) standard rear tank 52 gallons 197 liters optional midship tank 22 gallons 83 liters engine oil with filter 5.7l engine (sae 5w-20, api certified) 7 quarts 6.6 liters cooling system 5.7l engine (mopar 威 antifreeze/coolant 5 year/100,000 mile formula) or...

  • Page 444

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5–year/100,000 mile formula hoat (hy- brid organic additive technology) or equivalent. Engine oil – 5.7l engine use api certified sae 5w-20 engine oil, meeting the requir...

  • Page 445

    Chassis component fluid, lubricant, or genuine part automatic transmission (five-speed 545rfe) mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Transfer case mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Front and rear axle flu...

  • Page 447: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 446 ▫ 5.7l gas engine . . . . . . . . . . . . . . . . . . . . . 446 ▫ required maintenance intervals . . . . . . . . . . 448 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 448

    Maintenance schedule 5.7l gas engine the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe ope...

  • Page 449

    • under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or 6 months, whichever comes first. Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your auth...

  • Page 450

    At each oil change • change the engine oil filter. • inspect the brake hoses and lines. Caution! Failure to perform the required maintenance items may result in damage to the vehicle. Required maintenance intervals refer to the maintenance schedules on the following pages for the required maintenanc...

  • Page 451

    8,000 miles (13,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). ❏ lube the front drive shaft fitting (4x4 only). Odometer reading date rep...

  • Page 452

    24,000 miles (39,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). ❏ lube the front drive shaft fitting (4x4 only). ❏ inspect the cv joint...

  • Page 453

    40,000 miles (65,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). ❏ lube the front drive shaft fitting (4x4 only). Odometer reading date ...

  • Page 454

    56,000 miles (91,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). ❏ lube the front drive shaft fitting (4x4 only). Odometer reading date ...

  • Page 455

    64,000 miles (104,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). ❏ replace the engine air cleaner filter. ❏ replace the spark plugs. ❏...

  • Page 456

    72,000 miles (117,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ lube the front drive shaft fitting (4x4 only). ❏ inspect the cv joi...

  • Page 457

    88,000 miles (143,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). ❏ lube the front drive shaft fitting (4x4 only). Odometer reading dat...

  • Page 458

    96,000 miles (156,000 km) or 72 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏ replace the engine air cleaner filter. ❏ replace the spark plugs. ❏...

  • Page 459

    104,000 miles (169,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ lube the front drive shaft fitting (4x4 only). ❏ flush and replac...

  • Page 460

    120,000 miles (195,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏ lube the front drive shaft fitting (4x4 only). ❏ inspect the cv j...

  • Page 461

    128,000 miles (208,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). ❏ replace the engine air cleaner filter. ❏ replace the spark plugs....

  • Page 462

    144,000 miles (234,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). ❏ if using your vehicle for any of the following: dusty or off-roa...

  • Page 463

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about...

  • Page 465: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465 ▫ prepare for the appointment . . . . . . . . . . . 465 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 465 ▫ be reasonable with r...

  • Page 466

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 471 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 471 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 471 ▫ temperature grades . . . . . . . . . . . . . . . . . . 47...

  • Page 467

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 468

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 469

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 470

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 471

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 472

    • service manuals these comprehensive service manuals provide the infor- mation that students and professional technicians need in diagnosing/troubleshooting, problem solving, main- taining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, an...

  • Page 473

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 474

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 475: Index

    Index 10

  • Page 476

    Adding engine coolant (antifreeze) . . . . . . . . . . 411 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . 155 air cleaner, engine (engine air cleaner filter) . . . 401 air conditioner maintenance . . . . . . . . ....

  • Page 477

    Automatic transmission adding fluid . . . . . . . . . . . . . . . . . . . . . . . 422 fluid and filter changes . . . . . . . . . . . . . . . 422 fluid level check . . . . . . . . . . . . . . . . . 420,421 fluid type . . . . . . . . . . . . . . . . . . . . . . 420,443 shifting . . . . . . . . . . . ....

  • Page 478

    Cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 cellular phone . . . . . . . . . . . . . . . . . . . . . . . . 91,256 center high mounted stop light . . . . . . . . . . . . 437 center lap belts . . . . . . . . . . . . . . . . . . . . . . . . . 48 center seat storage compartme...

  • Page 479

    Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 413 points to remember . . . . . . . . . . . . . . . . . . 414 pressure cap . . . . . . . . . . . . . . . . . . . . . . . . 412 radiator cap . . . . . . . . . . . . . . . . . . . . . . . 412 selection of coolant (antifreeze) . . . . . . ...

  • Page 480

    Jump starting . . . . . . . . . . . . . . . . . . . . . . . 382 tow hooks . . . . . . . . . . . . . . . . . . . . . . . . . 387 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389 emission control system maintenance . . . . . . . . . 395 engine . . . . . . . . . . . . . . . . . . . . ...

  • Page 481

    Fluid level checks automatic transmission . . . . . . . . . . . . . . . . 421 brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416 power steering . . . . . . . . . . . . . . . . . . . . . . 299 fluid, brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 fluids, lubricants a...

  • Page 482

    Gross axle weight rating . . . . . . . . . . . . . . . . . . 341 gross vehicle weight rating . . . . . . . . . . . . . . . . 340 guide, body builders . . . . . . . . . . . . . . . . . . . . . . 6 gvwr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 hands-free phone (uconnect™) . . ...

  • Page 483

    Inside rearview mirror . . . . . . . . . . . . . . . . . . . . 83 instrument cluster . . . . . . . . . . . . . . . . . . . . 185,187 instrument panel and controls . . . . . . . . . . . . . . 184 instrument panel lens cleaning . . . . . . . . . . . . . 427 integrated power module (fuses) . . . . . . ...

  • Page 484

    Brake warning . . . . . . . . . . . . . . . . . . . . . . 195 bulb replacement . . . . . . . . . . . . . . . . . . . . 434 cap top clearance . . . . . . . . . . . . . . . . . . . 439 cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 center mounted stop . . . . . . . . . . . . . . ....

  • Page 485

    Lower anchors and tether for children (latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 lubrication, body . . . . . . . . . . . . . . . . . . . . . . . 405 lug nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . 376,379 maintenance free battery . . . . . . . . . . . . . ....

  • Page 486

    Change interval . . . . . . . . . . . . . . . . . . . . . 399 dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 filter . . . . . . . . . . . . . . . . . . . . . . . . . . 400,442 filter disposal . . . . . . . . . . ....

  • Page 487

    Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 power steering fluid . . . . . . . . . . . . . . . . . . . . . 443 pregnant women and seat belts . . . . . . . . . . . . . . 51 programmable electronic features . . . . . . . . . . . . 214 programming transmitters (remote keyless entry...

  • Page 488

    Safety checks inside vehicle . . . . . . . . . . . . . . . . . 76 safety checks outside vehicle . . . . . . . . . . . . . . . 78 safety defects, reporting . . . . . . . . . . . . . . . . . . 468 safety information, tire . . . . . . . . . . . . . . . . . . . 305 safety tips . . . . . . . . . . . . . ...

  • Page 489

    Automatic transmission . . . . . . . . . . . . . . . . 278 transfer case . . . . . . . . . . . . . . . . . . . . . . . 286 transfer case, shifting into transfer case neutral (n) . . . . . . . . . . . . . . . . . . . . . . 360,363 transfer case, shifting out of transfer case neutral (n) . . . . . . ....

  • Page 490

    Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 temperature control, automatic (atc) . . . . . . . . 261 temperature gauge, engine coolant . . . . . . . . . . 187 tether anchor, child restraint . . . . . . . . . . . . . 67,70 tilt steering column . . . . . . . . . . . . . . . ...

  • Page 491

    Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 recreational . . . . . . . . . . . . . . . . . . . . . . . . 358 weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 towing assistance . . . . . . . . . . . . . . . . . . . . . . . 105 traction . . . . . . . . . . . ....

  • Page 492

    Vehicle modifications/alterations . . . . . . . . . . . . . . 7 vehicle storage . . . . . . . . . . . . . . . . . . . . . . . 267,433 voice recognition system (vr) . . . . . . . . . . . . . . 122 voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 warning lights (instrument clust...

  • Page 493

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 494

    Dakota chrysler group llc o w n e r ’ s m a n u a l 2 0 1 1 2011 dakota 11dd43-126-af sixth edition printed in u.S.A..