1. DL manuals
  2. RAM
  3. Trucks
  4. Chassis Cab 2014
  5. Owner's Manual

RAM Chassis Cab 2014 Owner's Manual

Manual is about: Commercial

Summary of Chassis Cab 2014

  • Page 1

    C h a s s i s c a b chrysler group llc o w n e r ’ s m a n u a l 2 0 1 4 2014 chassis cab 14dd43-126-aa first edition printed in u.S.A..

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .4 䡵 warnings and cautions . . . . . . . . . . . . . .6 䡵 van conversions/campers . . . . . . . . . . . .6 䡵 vehicle identification number . . . . . . . .6 䡵 vehic...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 9

    Frame and underbody as well as the automobile infor- mation disclosure label affixed to a window on your vehicle, the vehicle registration and title. Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seri...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition node module (ignm) — if equipped. .12 ▫ keyless ignition node (kin) — if equipped . . .13 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ removing key fob from...

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . .27 ▫ programming additional transmitters. . . . . . . .28 ▫ transmitter battery replacement . . . . . . . . . . .28 ▫ general information . . . . . . . . . . . . . . . . . . . .31 䡵 remote starting system — if equipped . . .32 ▫ how to use r...

  • Page 13

    ▫ driver and right front passenger supplemental restraint system (srs) — air bags . . . . . . . . .64 ▫ air bag system components . . . . . . . . . . . . . .65 ▫ advanced front air bag features . . . . . . . . . . .66 ▫ air bag deployment sensors and controls . . . .67 ▫ event data recorder (edr) . ...

  • Page 14

    A word about your keys your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a bladed key with an immobilizer chip in it, or a key fob with remote keyless entry (rke) transmitter and an ignition node module (ignm). The key...

  • Page 15

    Keyless ignition node (kin) — if equipped this feature allows the driver to operate the ignition switch with the push of a button, as long as the remote keyless entry (rke) transmitter is in the passenger compartment. The keyless ignition node (kin) has four operating positions, three of which are l...

  • Page 16

    Note: for further information, refer to starting proce- dures in “starting and operating”. Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote...

  • Page 17

    Note: you can insert the double-sided emergency key into the lock cylinder with either side up. Emergency key removal (ignm) emergency key removal keyless enter-n-go™ fob (kin) 2 things to know before starting your vehicle 15.

  • Page 18

    Removing key fob from ignition place the shift lever in park (if equipped with an automatic transmission). Turn the key fob to the off position and then remove the key fob. Note: • for vehicles not equipped with the electronic vehicle information center (evic), the power window switches, radio, powe...

  • Page 19

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and push ignition button to place ignition in off position. When leaving the vehicle, always lock your ve- hicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. •...

  • Page 20

    Key-in-ignition reminder opening the driver’s door when the key fob is in the ignition and the ignition switch position is off or acc, a chime will sound to remind you to remove the key fob. Note: • ⬙keyed⬙ ignition systems will chime in off or acc when the driver door is open. • “keyless⬙ ignition ...

  • Page 21

    During normal operation, after turning on the ignition switch, the vehicle security light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb...

  • Page 22

    Caution! • always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unat- tended. • for vehicles equipped with keyless enter-n-go™, always remember to place the ignition in the off position. At the time of purchase, the original owner is provided with a four-digit pers...

  • Page 23

    Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Vehicle security alarm the vehicle security alarm monitors the vehicle doors and ignition for unauthorized operation. When the ve- hicle security al...

  • Page 24

    The horn will sound three times when you unlock the doors and the exterior lights will blink three times. Check the vehicle for tampering. The vehicle security alarm will also disarm if a pro- grammed sentry key® is inserted into the ignition switch. To exit the alarming mode, press the rke trans- m...

  • Page 25

    Note: • the front courtesy overhead console and door cour- tesy lights will not turn off if the dimmer control is in the “dome on” position (rotate horizontal thumb wheel on the bottom of the switch to the far right detent position). • the illuminated entry system will not operate if the dimmer cont...

  • Page 26

    Remote unlock the doors press and release the unlock button on the rke transmitter once to unlock the driver’s door (if evic is setup for driver door first, otherwise this will unlock all doors), or press the unlock button twice within five key fob with remote keyless entry (rke) transmitter key fob...

  • Page 27

    Seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote key unlock, driver door/all doors first this feature lets you program the system to unlock either the driver’s door or all doors on the first press ...

  • Page 28

    Flash lamps with remote key lock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to “...

  • Page 29

    Sound horn with remote key lock this feature will cause the horn to chirp when the doors are locked with the rke transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to “elec- tronic vehicle informat...

  • Page 30

    The headlights will turn on, the park lights will flash, the horn will pulse on and off, and the interior lights will turn on. The panic alarm will stay on for three minutes unless you turn it off by either pressing the panic button a second time or drive the vehicle at a speed of 5 mph (8 km/h) or ...

  • Page 31

    2. Separating rke halves requires screw removal and gently prying the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. Ignition node module (ignm) emergency key removal keyless ignition node (kin) emergency key removal 2 things to know before starting your ve...

  • Page 32

    Remove screw from transmitter case separating ignition node module (ignm) transmitter case 30 things to know before starting your vehicle.

  • Page 33

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the b...

  • Page 34

    Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. If your rke transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the transmitter. The expected ...

  • Page 35

    • battery at an acceptable charge level • rke panic button not pressed • fuel meets minimum requirement • system not disabled from previous remote start event • vehicle security alarm not active warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon...

  • Page 36

    To enter remote start mode press and release the remote start button on the rke transmitter twice within five sec- onds. The parking lights will flash, vehicle doors will lock, and the horn will chirp twice (if programmed). Once the vehicle has started, the engine will run for 15 minutes. Note: • if...

  • Page 37

    To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, press and release the unlock button on the rke transmitter to unlock the doors and disarm the vehicle security alarm system (if equipped). Then, prior to the end of the 15 minute cycle, press and release the start...

  • Page 38

    Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed. The emergency key will unlock the driver door lock on your vehicle. Warning! • do not leave children or animals inside parked vehicles in hot weather. Inte...

  • Page 39

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking...

  • Page 40

    Operate. A chime will sound if the key fob is in the ignition switch and a door is open, as a reminder to remove the key fob. Automatic door locks — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exce...

  • Page 41

    To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to engage and disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the u...

  • Page 42

    Note: • after setting the child-protection door lock system, always test the door from the inside to make certain it is in the desired position. • for emergency exit with the system engaged, move the door lock switch to the unlock position, roll down the window and open the door with the outside doo...

  • Page 43

    The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of the quad cab and crew cab models. The windows will operat...

  • Page 44

    To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly. To open the window part way, press to the first detent and release it when you want the window to stop. Auto-up feature with anti-pinch protection (4-door models driver and front passenger d...

  • Page 45

    2. Pull the window switch up to close the window completely and continue to hold the switch up for an additional two seconds after the window is closed. 3. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two...

  • Page 46

    Open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sun- roof opening to minimize t...

  • Page 47

    To unlock from the driver’s side: with a valid passive entry rke transmitter within 5 ft (1.5 m) of the driver door handle, grab the front driver door handle to unlock the driver’s door automatically. The interior door panel lock knob will raise when the door is unlocked. Note: if “unlock all doors ...

  • Page 48

    Preventing inadvertent locking of passive entry rke transmitter in vehicle to minimize the possibility of unintentionally locking a passive entry rke transmitter inside your vehicle, the passive entry system is equipped with an automatic door unlock feature which will function if the ignition switch...

  • Page 49

    Do not grab the door handle when pressing the door handle lock button. This could unlock the door(s). Note: • after pressing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if t...

  • Page 50

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for the driver and all passengers • advanced front air bags for driver and front passen- ger • an energy-absorbing steering column and steering wheel • knee ...

  • Page 51

    1. Children 12 years old and under should always ride buckled up in a rear seat. Warning! • never place a rear facing infant seat in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward fac...

  • Page 52

    The customer center. Phone numbers are provided under “if you need assistance”. Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wea...

  • Page 53

    Lock and reduce the risk of you striking the inside of the vehicle or being thrown out. Warning! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of t...

  • Page 54

    Warning! (continued) • two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. Lap/shoulder belt operating ...

  • Page 55

    Warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden stop you...

  • Page 56

    Warning! (continued) • a belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your s...

  • Page 57

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt may not protect you properly. In a collisi...

  • Page 58

    Regular cab front center three point belt 1. The front center seat belt on the regular cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger ...

  • Page 59

    Inserting latch plate in use position 2 things to know before starting your vehicle 57.

  • Page 60

    Warning! • if the black latch and black buckle are not properly connected when the seat belt is used by an occu- pant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • when reattaching the black latch and black buckle, ensure the seat ...

  • Page 61

    As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Center lap belts the center seating position for t...

  • Page 62

    Seat belts in passenger seating positions the seat belts in the passenger seating positions are equipped with an automatic locking retractor (alr) or a cinching latch plate which are used to secure a child restraint system. For additional information refer to “installing child restraints using the v...

  • Page 63

    Warning! • the belt and retractor assembly must be replaced if the seat belt assembly automatic locking retractor (alr) feature or any other seat belt function is not working properly when checked according to the procedures in the service manual. • failure to replace the belt and retractor assembly...

  • Page 64

    3. Allow the belt to retract. As the belt retracts, you will hear a ratcheting sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the au...

  • Page 65

    Unbuckled while traveling at speeds greater than 5 mph (8 km/h), beltalert® will provide both audio and visual notification. The front passenger seat beltalert® is not active when the front passenger seat is unoccupied. Beltalert® may be triggered when an animal or heavy object is on the front passe...

  • Page 66

    Warning! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug and in the recommended seating posi- tions. Remove and store the extender when not needed. Driver and right front passenger ...

  • Page 67

    The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adj...

  • Page 68

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc). The first stage inflator is triggered immediat...

  • Page 69

    Along with seat belts and pretensioners, advanced front air bags work with the knee impact bolsters to provide improved protection for the driver and front passenger. Air bag deployment sensors and controls occupant restraint controller (orc) the orc is part of a federally regulated safety system re...

  • Page 70

    The orc monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the start or on/run position. If the key is in the lock position, in the acc position, or not in the ignition, the air bag system is not on and the air bags will not inflate. The orc conta...

  • Page 71

    When the orc detects a collision requiring the ad- vanced front air bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the advanced front air bags. Different air bag inflation rates are possible, based on several factors, including the collision type and s...

  • Page 72

    If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: advanced front air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or all o...

  • Page 73

    Warning! (continued) assembly replaced by an authorized dealer immedi- ately. Also, have the occupant classification system serviced as well. Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if th...

  • Page 74

    Air bag warning light you will want to have the air bags ready to inflate for your protection in a collision. The air bag warning light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenan...

  • Page 75

    • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if at all) the driver was depressing the accelerator and/or brake pedal; and, • how fast the vehicle was traveling. These data can help provide a better understanding of the circumstances in which crashes and in...

  • Page 76

    Warning! In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in you...

  • Page 77

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 78

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 79

    Have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above t...

  • Page 80

    Warning! (continued) • when your child restraint is not in use, secure it in the vehicle with the seat belt or latch anchor- ages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal ...

  • Page 81

    If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check belt fit peri- odically and make sure the seat belt buckle is latched. A child’s squirming or slouching can move the belt out of posi...

  • Page 82

    Recommendations for attaching child restraints — quad cab®/crew cab restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-f...

  • Page 83

    Recommendations for attaching child restraints — standard cab, mega cab® restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor r...

  • Page 84

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 85

    Latch positions for installing child restraints in this vehicle standard cab lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol 2 things to know before starting your vehicle 83.

  • Page 86

    Quad cab®/crew cab full bench lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol quad cab®/mega cab®/crew cab split bench lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol 84 things to know before starting your vehicle.

  • Page 87

    Quad cab®/crew cab what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the...

  • Page 88

    Can two child restraints be at- tached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to install a child seat in the center position next to a child s...

  • Page 89

    Mega cab®/standard cab what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the com- bined weight of the child and the child restraint is 65 lbs (29.5 kg). U...

  • Page 90

    Can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint own- er’s manual for more information. Can the head restraints be remove...

  • Page 91

    Locating the latch anchorages in addition, regular cab models have tether strap anchorages behind the front center and right seats. Quad cab®, mega cab® and crew cab models have tether strap anchorages lo- cated behind each of the rear seats. 1 — tether strap hook 2 — tether strap to child restraint...

  • Page 92

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing infant restraint...

  • Page 93

    Center seat latch — quad cab®/mega cab®/crew cab split bench if a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard latch anchors or seat bel...

  • Page 94

    Move it to its rear-most position to make room for the child seat. You may also move the front seat forward to allow more room for the car seat. 4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has a ...

  • Page 95

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • child restraint anchorages are...

  • Page 96

    Lap/shoulder belt systems for installing child restraints in this vehicle standard cab quad cab®/mega cab®/crew cab 94 things to know before starting your vehicle.

  • Page 97

    Quad cab®/crew cab what is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child re- straint always use the tether anchor when using the seat belt to install a forward fac...

  • Page 98

    Mega cab®/standard cab what is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? 65 lbs (29.5 kg) the tether anchor can be used with the seat belt until the combined weight of the child and the...

  • Page 99

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 100

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 101

    Strap. Refer to “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25 mm) in any direction. Any...

  • Page 102

    1 — tether strap hook 2 — tether strap to child restraint 3 — tether anchor 2. Route the tether strap to provide the most direct path between the anchorage and the child seat. The tether strap should go between the head restraint posts underneath the head restraint. You may need to adjust the head r...

  • Page 103

    Warning! Never place a rear facing infant seat in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. Quad cab® or crew cab trucks: the top tether an- chorages in this ...

  • Page 104

    2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint, through the tether strap loop behind the seat and over to the tether strap loop behind the center seat. Head restraint in raised position tether strap loop with cent...

  • Page 105

    3. Pass the tether strap hook under the head restraint behind the child seat, though the tether strap loop behind the seat and over to the center tether strap loop. 4. Attach the hook to the center tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s i...

  • Page 106

    Note: if there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connected to the center tether strap loop. This is the correct way to tether two outboard child seats. Center seat: 1. Raise the head restraint and reach be...

  • Page 107

    3. Pass the tether strap hook under the head restraint behind the child seat, though the tether strap loop behind the seat and over to the right or left outboard tether strap loop. 4. Attach the hook to the outboard tether strap loop (see diagram). Tighten the tether strap according to the child sea...

  • Page 108

    Installing three child restraints: 1. Place a child restraint on each outboard rear seat. Route the tether straps following the directions for right and left seating positions, above. 2. Attach both hooks to the center tether strap loop, but do not tighten the straps yet. 3. Place a child restraint ...

  • Page 109

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 110

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of diff...

  • Page 111

    Loaded operating conditions which allow the engine parts to achieve final finish and fit during the first 6,000 miles (10 000 km). Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Inte...

  • Page 112

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can even- tually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confin...

  • Page 113

    Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat b...

  • Page 114

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 115

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 117: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 ▫ inside day/night mirror . . . . . . . . . . . . . . . .119 ▫ automatic dimming mirror — if equipped . . .120 ▫ automatic dimming mirror with rear view camera display — if equipp...

  • Page 118

    ▫ 40-20-40 front bench seat — if equipped . . . .139 ▫ head restraints . . . . . . . . . . . . . . . . . . . . . .139 䡵 driver memory seat — if equipped . . . .141 ▫ programming the memory feature . . . . . . . . .142 ▫ linking and unlinking the remote keyless entry transmitter to memory . . . . . ....

  • Page 119

    ▫ flash-to-pass . . . . . . . . . . . . . . . . . . . . . . . .158 ▫ high/low beam switch . . . . . . . . . . . . . . . .159 䡵 windshield wipers and washers . . . . . .159 ▫ windshield wipers . . . . . . . . . . . . . . . . . . . .159 ▫ windshield wiper operation . . . . . . . . . . . . .160 ▫ inter...

  • Page 120

    䡵 cupholders . . . . . . . . . . . . . . . . . . . . . . . .179 ▫ front seat cupholders (40–20–40 seats) . . . . . .179 ▫ front instrument panel cupholders — floor storage bin . . . . . . . . . . . . . . . . . . . . . . . . . .179 ▫ rear cupholder — crew cab . . . . . . . . . . . . .180 䡵 storage . ...

  • Page 121

    Mirrors inside day/night mirror a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjus...

  • Page 122

    Automatic dimming mirror — if equipped a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can b...

  • Page 123

    Assist call the rear view mirror contains an assist push button which automatically connects the vehicle occupants to one of several predefined locations for immediate sup- port: • roadside assistance – if you get a flat tire, or need a tow, just press the assist button and you’ll be con- nected to ...

  • Page 124

    4. You should be able to speak with the 9-1-1 operator through the vehicle audio system to determine if additional help is needed. Note: once a connection is made between the vehicle’s 9-1-1 call system and the 9-1-1 operator, the 9-1-1 opera- tor may be able to open a voice connection with the vehi...

  • Page 125

    Warning! (continued) • modifications to any part of the 9-1-1 call system could cause the air bag system to fail when you need it. You could be injured if the air bag system is not there to help protect you. 9-1-1 call system limitations vehicles sold in canada and mexico do not have 9-1-1 call syst...

  • Page 126

    Even if the 9-1-1 call system is fully functional, factors beyond chrysler group llc’s control may prevent or stop the 9-1-1 call system operation. These include, but are not limited to, the following factors: • the ignition key has been removed from the ignition and the delayed accessories mode is ...

  • Page 127

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Automatic dimming mirror with rear view camera display — if equipped a single ball joint mirror is provided in the vehi...

  • Page 128

    Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they ...

  • Page 129

    Caution! It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location. Power mirrors — if equipped the controls for the power mirrors are located on the driver’s door trim panel. Power mirror controls location 3 understanding th...

  • Page 130

    The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a mirror, press either the l (left) or r (right) button to select the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that y...

  • Page 131

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Refer to “rear window features” in “understanding the features of your vehicle” for further information. Illuminated vanity mirror —...

  • Page 132

    To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until the sun visor is in the desired position. Trailer towing mirrors — if equipped these mirrors are designed with an adjustable mirror head to provide a greater vision range...

  • Page 133

    Note: fold the trailer towing mirrors rearward prior to entering an automated car wash. A small blindspot mirror is located next to main mirror and can be adjusted separately. Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, ...

  • Page 134

    Driver’s power seat — if equipped some models may be equipped with an eight-way power driver’s seat. The power seat switches are located on the outboard side of the driver’s seat cushion. There are two power seat switches that are used to control the move- ment of the seat cushion and the seatback. ...

  • Page 135

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 136

    Caution! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Tilting the seat up or down the angle of the seat cushion can be adjusted in fou...

  • Page 137

    The seat switch, the front of the seat cushion will move in the direction of the switch. Release the switch when you have reached the desired position. Power lumbar — if equipped vehicles equipped with power driver or passenger seats may be also be equipped with power lumbar. The power lumbar switch...

  • Page 138

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 139

    • the engine must be running for the heated seats to operate. When the high-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal high-level. If the high-level setting is selected, the system ...

  • Page 140

    Vehicles equipped with remote start on models equipped with remote start, the drivers ventilated seat can be programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further information. Manual seat adjuster — i...

  • Page 141

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 142

    Reclining rear seats — if equipped the recliner handle is located on the outside of the seat cushion. To adjust the seatback, lift upward on the handle, lean back on the seatback and when you reach the desired position, release the handle. Warning! Do not ride with the seatback reclined so that the ...

  • Page 143

    Note: the rear center head restraint (crew cab only) is fixed and cannot be adjusted. Driver memory seat — if equipped this feature allows the driver to store up to two different memory profiles for easy recall through a memory switch. Each memory profile contains desired position settings for the d...

  • Page 144

    The memory seat buttons are located on the outboard side of the drivers seat cushion. Programming the memory feature note: to create a new memory profile, perform the following: vehicles equipped with keyless enter-n-go 1. Without pressing the brake pedal, push the engine start/stop button and cycle...

  • Page 145

    Vehicles not equipped with keyless enter-n-go 1. Insert the ignition key fob, and turn the ignition switch to the on/run position. 2. Adjust all memory profile settings to desired prefer- ences (seat, side mirrors, adjustable pedals [if equipped], power tilt and telescopic steering column [if equipp...

  • Page 146

    Note: before programming your rke transmitters you must select the “memory to fob” feature through the uconnect® system screen. Refer to “customer- program- mable features — uconnect® access 8.4 settings ” in “understanding your instrument panel” for further in- formation. To program your rke transm...

  • Page 147

    Driver one memory position recall • to recall the memory settings for driver one using the memory switch, press memory button number 1 on the memory switch. • to recall the memory settings for driver one using the rke transmitter, press the unlock button on the rke transmitter linked to memory posit...

  • Page 148

    2. Reach into the opening beneath the center of the hood and push the safety latch lever to the left to release it, before raising the hood. Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches eng...

  • Page 149

    Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. Lights the headlight switch is located on the left side...

  • Page 150

    To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Caution! Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the le...

  • Page 151

    Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to the auto position. When the system is on, the headlight delay feature is also on. This means the headlights will stay o...

  • Page 152

    Daytime running lights (drl) — if equipped the headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except park. This provides a constant ⬙lights on⬙ condition until the ignition is turned off. The lights illuminate at less than 50% of normal inte...

  • Page 153

    Detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. Note: • automatic high beam headlamp control can be turned on or off using the uconnect® system, refer to “uconnect® settings” in “understanding your instru- ment pane...

  • Page 154

    To deactivate perform either of the following steps to deactivate the automatic high beam system. 1. Select “automatic high beams — off” through the evic. Refer to “electronic vehicle information center (evic)/customer-programmable features” in “un- derstanding your instrument panel” for further inf...

  • Page 155

    The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pushed a second time, when the headlight sw...

  • Page 156

    If the headlights remain on while the ignition is cycled off, the exterior lights will automatically turn off after eight minutes. If the headlights are turned on and left on for eight minutes while the ignition is off, the exterior lights will automatically turn off. Note: battery saver mode is can...

  • Page 157

    Courtesy/reading lights both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the unlock button is pressed on the remote keyless ent...

  • Page 158

    Note: the courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the ignition is turned off, they will automatically turn off after 15 minutes. Ambient light the overh...

  • Page 159

    Cargo light the cargo lights are turned on by pressing on the cargo button. The cargo lights will also turn on for approximately 30 seconds when a rke transmitter unlock button is pressed, as part of the illuminated entry feature. Multifunction lever the multifunction lever is located on the left si...

  • Page 160

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside l...

  • Page 161

    High/low beam switch push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction lever back toward the steering wheel will turn the low beams back on, or shut the high beams off. Windshield wipers and washers windshield wipers the wipers ...

  • Page 162

    Windshield wiper operation rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation. Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper opera- tion. Intermittent wiper system the inte...

  • Page 163

    Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist feature when...

  • Page 164

    • the rain sensing feature may not function properly when ice, or dried salt water is present on the wind- shield. • use of rain-x® or products containing wax or silicone may reduce rain sensing performance. • a customer programmable feature in the electronic vehicle information center (evic) allows...

  • Page 165

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the multifunction lever. Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wheel, move the s...

  • Page 166

    Warning! (continued) the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Driver adjustable pedals — if equipped the adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. ...

  • Page 167

    Adjusted when the system is locked out (“adjustable pedal disabled — cruise control engaged” or “ad- justable pedal disabled — vehicle in reverse”. Note: • always adjust the pedals to a position that allows full pedal travel. • further small adjustments may be necessary to find the best possible sea...

  • Page 168

    Approximately 30 to 80 minutes before automatically shutting off. The heated steering wheel can shut off early or may not turn on when the steering wheel is already warm. The heated steering wheel switch is located on the switch bank below the climate controls. There are also soft-keys in the radio ...

  • Page 169

    Warning! (continued) • do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. Electronic speed control when engaged, the electronic speed control takes over ac...

  • Page 170

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 171

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate the electronic speed control with- out erasing the set speed memory. Pressing the on/off button or turning the ignition switch off erases the set speed memory. T...

  • Page 172

    To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The speed decrement shown is dependant on the speed of u.S. (mph) or metric (km/h) units: u.S. Speed (mph) • pressing the set (-) button once will result in a 1 mph decrease in set spe...

  • Page 173

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 174

    (rke) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens. Note: the courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the int...

  • Page 175

    Electrical power outlets the auxiliary 12 volt (13 amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 volt power outlets have a cap attached to the outlet indicating “12v dc,” together with either a key symbol or a battery symb...

  • Page 176

    • center console when equipped with bucket seats. • inside the upper lid of the center storage compartment — if equipped. Power outlets — center stack power outlet — center console 174 understanding the features of your vehicle.

  • Page 177

    • rear of the center console storage compartment — quad cab® or crew cab. The key symbol indicates that this outlet can supply power when the key is in the on/run or acc positions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect th...

  • Page 178

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 179

    Cigar lighter and ash receiver — if equipped a removable ash receiver and cigar lighter are available. For vehicles with a bench seat the cupholder tray can be used to hold the ash receiver. For vehicles equipped with a floor console, the cuphold- ers may be used. Ash receiver and cigar lighter (ben...

  • Page 180

    Power inverter — if equipped a 115 volt (150 watts maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such as ...

  • Page 181

    Warning! To avoid serious injury or death: • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Cupholders front seat cupholders (40–20–40 seats) the cupholders ar...

  • Page 182

    Rear cupholder — crew cab crew cab vehicles are equipped with rear cupholders located in the center armrest. Crew cab vehicles may be equipped with a rear cup- holder that consists of two cup wells for rear passenger convenience. Crew cab rear armrest cupholder rear cup wells 180 understanding the f...

  • Page 183

    Storage glove compartment the glove compartment is located on the passenger side of the instrument panel and features both an upper and lower storage area. Glove compartment 1 — upper glove compartment 2 — lower glove compartment 3 understanding the features of your vehicle 181.

  • Page 184

    To open the upper glove compartment push upward on the handle release. The glove compartment door will automatically open. To open the lower glove compartment, pull on the handle to release the latch and lower the glove compartment door. Upper glove compartment lower glove compartment 182 understand...

  • Page 185

    Door storage front door storage — if equipped storage areas and bottle holders (drivers side only) are located in the door trim panels. Rear door storage — crew cab storage compartments are located in both the driver and passenger door trim panels. Front door storage rear door storage 3 understandin...

  • Page 186

    Center storage compartment — if equipped the center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Warning! • this armrest is not a seat. Anyone seated on the armrest could be seri...

  • Page 187

    With the upper lid closed, pull on the lower handle to open the lower storage bin. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Upper storage compartment lower storage bi...

  • Page 188

    Seatback storage located in the back of both the driver and passenger front seats are pockets that can be used for storage. Storage (regular cab) the storage bin is located behind the front seats and runs the length of the cab. Drivers side seatback storage storage bin 186 understanding the features...

  • Page 189

    Storage and seats (crew cab) the crew cab models provide additional storage under the rear seats. Lift the seats to access the storage com- partment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Caution! Always lift the storage compartment lids by using ...

  • Page 190

    Rear window features rear window defroster the rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. T...

  • Page 191

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 193: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .193 䡵 instrument cluster . . . . . . . . . . . . . . . . .194 䡵 instrument cluster — premium . . . . . . .195 䡵 instrument cluster descriptions . . . . .196 䡵 electronic vehicle information center (evic) . . ...

  • Page 194

    ▫ radio operation . . . . . . . . . . . . . . . . . . . . . .262 ▫ cd player. . . . . . . . . . . . . . . . . . . . . . . . . . .263 䡵 cd/dvd disc maintenance . . . . . . . . . . .263 䡵 radio operation and mobile phones . .264 䡵 climate controls . . . . . . . . . . . . . . . . . . .264 ▫ manual clim...

  • Page 195

    Instrument panel features 1 — headlight switch 7 — 115v power inverter outlet 13 — gear selector/transfer case position switch — if equipped 2 — instrument cluster 8 — power outlet 14 — ignition switch 3 — radio 9 — lower switch bank 15 — hood release 4 — hazard switch 10 — instrument panel drawer 1...

  • Page 196

    Instrument cluster 194 understanding your instrument panel.

  • Page 197

    Instrument cluster — premium 4 understanding your instrument panel 195.

  • Page 198

    Instrument cluster descriptions 1. Tachometer the tachometer indicates engine speed in revolutions per minute (rpm x 1000). Caution! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine operation over 3200 rpm (redline) can result in significant damage that ...

  • Page 199

    Testing the light will come on when the ignition is first turned on and remain on for 15 seconds, then blink for 5 seconds, and remain on until the vehicle is started. If the bulb does not come on during starting, have the condi- tion investigated promptly. If this light comes on and remains on whil...

  • Page 200

    4. Turn signal indicators the arrow will flash with the exterior turn signal when the turn signal lever is operated. Note: • a continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. • check for an inoperative outside light bulb if either indicator ...

  • Page 201

    If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the brake booster has been detected by the anti-lock brake system (abs) / el...

  • Page 202

    Operation of the brake warning light can be checked by turning the ignition switch from the off position to the on/run position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light ...

  • Page 203

    Driving, have the system inspected at an authorized dealer as soon as possible. Refer to “occupant restraints” in “things to know before starting your vehicle” for further information. 10. Oil pressure gauge — if equipped the pointer should always indicate some oil pres- sure when the engine is runn...

  • Page 204

    16. Tire pressure monitoring telltale light — if equipped each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (if your vehicle has tir...

  • Page 205

    Of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the tpms from functioning properly. Always check the tpms malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires...

  • Page 206

    19. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: the highest available transmission gear is dis- played in the lower right corner of the electronic vehicle information center (evic)...

  • Page 207

    Running, a malfunction has been detected in the esc system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and cor...

  • Page 208

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “maintaining your vehicle.” follow the warnings unde...

  • Page 209

    If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough ...

  • Page 210

    31. 4 low this light alerts the driver that the vehicle is in the four-wheel drive low mode. The front and rear driveshafts are mechanically locked to- gether forcing the front and rear wheels to rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque ...

  • Page 211

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. This system allows the driver to select a variety of useful information by pressing the switches mounted on the steering wh...

  • Page 212

    • vehicle settings (not equipped with a uconnect® 5.0 & 8.4 radio) the system allows the driver to select information by pressing the following buttons mounted on the steering wheel: • up arrow button press and release the up arrow button to scroll upward through the main menu and sub- menus (fuel e...

  • Page 213

    • select/right arrow button press and release the select/right arrow button to access/select the information screens or sub-menu screens of a main menu item. Press and hold the select/right arrow button for two seconds to reset displayed/selected fea- tures that can be reset. • left arrow button pre...

  • Page 214

    The evic displays are located in the center portion of the cluster and consists of seven sections: 1. Compass display displays the current direction. For further information, refer to “compass settings” under “customer program- mable features — uconnect® 5.0/8.4 settings”. 2. Temperature display dis...

  • Page 215

    • hill decent control (hdc) — if equipped the hill decent control symbol indicates the status of the hill descent control (hdc) feature. The lamp will be on solid when hdc is armed. Hdc can only be armed when the transfer case is in the “4wd low” position and the vehicle speed is less then 30 mph (4...

  • Page 216

    Warning! If you continue operating the vehicle when the transmission temperature warning light is illumi- nated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. • air suspension payload protection telltale — if equipped this telltale wil...

  • Page 217

    • oil pressure warning light this telltale indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not s...

  • Page 218

    If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough ...

  • Page 219

    Messages that consist of approximately 60 possible warn- ing or information messages. These pop up messages fall into several categories: • five second stored messages when the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns...

  • Page 220

    Electronic vehicle information center (evic) displays — 7” display the evic displays are located in the center portion of the cluster and consists of eight sections: 1. Main screen — the inner ring of the display will illuminate in grey under normal conditions, yellow for non critical warnings, red ...

  • Page 221

    9. Selectable gauge 2 10. Selectable gauge 1 11. Selectable gauge 1 the main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warn- ing or informatio...

  • Page 222

    Seconds and then returns to the previous screen. An example of this message type is “automatic high beams on”. Evic amber telltales this area will show reconfigurable amber caution tell- tales. These telltales include: • low fuel telltale when the fuel level reaches approximately 3.0 gal (11.0 l) th...

  • Page 223

    Caution! Continuous driving with the transmission tempera- ture warning light illuminated will eventually cause severe transmission damage or transmission failure. Warning! If you continue operating the vehicle when the transmission temperature warning light is illumi- nated you could cause the flui...

  • Page 224

    • loose fuel filler cap this telltale will turn on to indicate that the fuel filler cap may be loose. Evic white telltales • electronic speed control ready this light will turn on when the electronic speed control is on. For further information, refer to “electronic speed control” in “under- standin...

  • Page 225

    • oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. • charging system light this light shows the status of the electrical charg- ing system. If the light stays on or...

  • Page 226

    • engine temperature warning light this light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches h, this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass h, a c...

  • Page 227

    Evic selectable menu items press and release the up or down arrow buttons until the desired selectable menu icon is highlighted in the evic. Digital speedometer press and release the up or down arrow button until the digital display icon is high- lighted in the evic. Press and release the select/rig...

  • Page 228

    Tire pressure information system (3500 series heavy duty ram trucks) press and release the up or down arrow button until “tire pressure” is highlighted in the evic. Press and release the select/right arrow button and one of the following will be displayed: a vehicle icon is displayed with the tire p...

  • Page 229

    Trip b press and release up & down arrow button until the trip b icon is highlighted in the evic. The trip b information will display the following: • distance • average fuel economy • average speed • elapsed time hold the select/right arrow button to reset all the information. Fuel economy press an...

  • Page 230

    Trailer tow press and release the up or down arrow button until the trailer tow icon is highlighted. Press the select/right arrow button and the next screen will display the following trailer trip information: • trailer trip • trailer brake audio press and release the up or down arrow button until t...

  • Page 231

    Upper left • none • compass • outside temp (default setting) • trans temp • oil temp • time • range to empty (rte) • average mpg • current mpg • trip a • trip b • trailer trip (distance only) • trailer brake gain upper right • none • compass (default setting) • outside temp • trans temp • oil temp •...

  • Page 232

    • trailer trip (distance only) • trailer brake gain lower left • none (default setting) • compass • outside temp • trans temp • oil temp • time • range • avg mpg • current mpg • trailer brake gain lower right • none (default setting) • compass • outside temp • trans temp • oil temp • time • range • ...

  • Page 233

    Restore to defaults (restores all settings to default settings) • cancel • okay engine oil change indicator system oil change required your vehicle is equipped with an engine oil change indicator system. The “oil change required” message will flash in the evic display for approximately 10 seconds af...

  • Page 234

    2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Electronic v...

  • Page 235

    • brake fluid low • service electronic braking system • engine temperature hot • battery voltage low • service electronic throttle control • lights on • right turn signal light out • left turn signal light out • turn signal on • vehicle not in park • key in ignition • key in ignition lights on • rem...

  • Page 236

    • door open • doors open • gear not available • shift not allowed • shift to neutral then drive or reverse • autostick unavailable service required • automatic unavailable use autostick service req. • transmission getting hot press brake • trans. Hot stop safely shift to park wait to cool • transmis...

  • Page 237

    For vehicles equipped with a 7” evic screen and not equipped with a uconnect® 8.4 radio. Personal settings allows the driver to set and recall features when the transmission is in park. Use the up or down button until personal settings displays in the evic. Press and release the select/right arrow b...

  • Page 238

    The feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Park assist system — if equipped the rear park assist system will scan for objects behind the vehicle when the transmission is in the reverse position and the vehicle speed is less...

  • Page 239

    Operating” for system function and operating informa- tion. To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Headlamp off delay when t...

  • Page 240

    Button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Refer to “lights/smartbeam™ — if equipped” in “un- derstanding the features of your vehicle” for further information. Daytime running ligh...

  • Page 241

    Select button until a check-mark appears next to the feature showing the system has been activated, or the check-mark is removed showing the system has been deactivated. Horn with remote start when this feature is selected, a short horn sound will occur when the rke transmitter remote start button i...

  • Page 242

    Key fob linked to memory when this feature is selected the memory seat, mirror, and radio settings will return to the memory set position when the rke transmitter unlock button is pressed. If this feature is not selected then the memory seat, mirror, and radio settings can only return to the memory ...

  • Page 243

    And release the select button until a check-mark ap- pears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Note: the seat will return to the memorized seat location (if recall memory with remote key unlock is set to on) ...

  • Page 244

    Setting has been selected. Refer to “integrated trailer brake module” in “starting and operating.” trailer name when this feature is selected, the trailer name can be selected from 16 names. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release ...

  • Page 245

    Press the screen off hard-key to turn off the uconnect® screen. Press the screen off hard-key a second time to turn the screen on. Press the back hard-key to exit out of a menu or certain option on the uconnect® system. Soft-keys soft-keys are accessible on the uconnect® display. Customer programmab...

  • Page 246

    Display after pressing the “display” soft-key the following set- tings will be available. • display mode when in this display you may select one of the auto display settings. To change mode status, touch and release the “day.” “night” or “auto” soft-key. Then touch the back arrow soft-key. • display...

  • Page 247

    • units when in this display, you may select to have the evic, odometer, and navigation system (if equipped) changed between us and metric units of measure. Touch “us” or “metric” until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to...

  • Page 248

    Until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. Clock after pressing the “clock” soft-key the following settings will be available: • sync time with gps when in this display, you may automatically h...

  • Page 249

    Safety & driving assistance after pressing the “safety & driving assistance” soft-key the following settings will be available. • park assist the rear park assist system will scan for objects behind the vehicle when the transmission shift lever is in re- verse and the vehicle speed is less than 11 m...

  • Page 250

    Selection, touch the “parkview® backup camera” soft- key, until a check-mark appears next to the setting, indicating that the setting had been selected. Touch the back arrow soft-key to return to the previous menu. • parkview® camera delay when this feature is enabled, it will allow the parkview bac...

  • Page 251

    Touch the “parkview® backup camera fixed guide- lines” soft-key, until a check-mark appears next to the setting, indicating that the setting had been selected. Touch the back arrow soft-key to return to the previous menu. • parkview® backup camera active guidelines your vehicle may be equipped with ...

  • Page 252

    Refer to “evic settings” or “uconnect® settings” in “understanding your instrument panel” for further in- formation. • rain sensing auto wipers when this feature is selected, the system will automati- cally activate the windshield wipers if it senses moisture on the windshield. To make your selectio...

  • Page 253

    Lights after pressing the “lights” soft-key the following set- tings will be available: • headlight illumination on approach when this feature is selected, the headlights will activate and remain on for 0, 30, 60, or 90 seconds when the doors are unlocked with the remote keyless entry (rke) transmit...

  • Page 254

    Check-mark appears next to the setting, showing that the setting has been selected. Touch the back arrow soft-key to return to the previous menu. • flash headlights with lock when this feature is selected, the headlights will flash when the doors are locked or unlocked with the remote keyless entry ...

  • Page 255

    Check-mark appears next to the setting, showing that the setting has been selected. Touch the back arrow soft-key to return to the previous menu. • sound horn with remote start when this feature is selected, the horn will sound when the remote start is activated. To make your selection, touch the “s...

  • Page 256

    Make your selection, touch the “passive entry” soft-key, until a check-mark appears next to the setting, showing that the setting has been selected. Touch the back arrow soft-key to return to the previous menu. Refer to “keyless enter-n-go™” in “things to know before starting your vehicle”. • memory...

  • Page 257

    • auto-on driver heated/ventilated seat & steering wheel with vehicle start — if equipped when this feature is selected the driver’s heated seat and heated steering wheel will automatically turn on when temperatures are below 40° f (4.4° c). When tempera- tures are above 80° f (26.7° c), the driver ...

  • Page 258

    Compass settings — if equipped after pressing the “compass settings” soft-key the fol- lowing settings will be available: • variance compass variance is the difference between magnetic north and geographic north. To compensate for the differences the variance should be set for the zone where the veh...

  • Page 259

    Also calibrate the compass by pressing the “on” soft-key and completing one or more 360-degree turns (in an area free from large metal or metallic objects) until the cal indicator displayed in the evic turns off. The compass will now function normally. Audio after pressing the “audio” soft-key the f...

  • Page 260

    To make your selection, touch the “aux volume match” soft-key, select on or off followed by pressing the back arrow soft-key. • loudness — if equipped the radio automatically turns on when vehicle is in run or will recall whether it was on or off at last ignition off. To make your selection, touch t...

  • Page 261

    System has been activated or the check-mark is removed showing the system has been deactivated. • suspension display messages when all is selected, all the air suspension alerts will be displayed. When warnings only is selected only the air suspension warnings will be displayed. • automatic aero mod...

  • Page 262

    Trailer brake • trailer select when this feature is selected, the trailer type can be selected between “trailer 1,” “trailer 2,” “trailer 3” and “trailer 4.” to make your selection, scroll up or down until the preferred setting is highlighted, then press and release the select button until a check-m...

  • Page 263

    • subscription information new vehicle purchasers or lessees will receive a free limited time subscription to siriusxm satellite radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the subscription information screen to re-subscribe...

  • Page 264

    Steering wheel audio controls — if equipped the remote sound system controls are located on the back surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a pushbutton in the center. Pressing the top of the switch will incre...

  • Page 265

    The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pre-set pushbuttons. Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginnin...

  • Page 266

    Radio operation and mobile phones under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the mobile phone antenna. This condition is not harmful to the radio. If your radio...

  • Page 267

    Front blower control there are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position. Note: for vehicles equipped with remote start, the climate controls ...

  • Page 268

    Temperature control use this control to regulate the tem- perature of the air inside the passenger compartment. Rotating the knob coun- terclockwise, from top center into the blue area of the scale, indicates cooler temperatures. Rotating the knob clock- wise, into the red area, indicates warmer tem...

  • Page 269

    Mode control (air direction) mode control allows you to choose from several patterns of air distribu- tion. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The closer the control is to a particular mode, the more air distribution you receive from...

  • Page 270

    Mix mode air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort, while reducing moisture on the windshield. Defrost mode air is directed thr...

  • Page 271

    • continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • in cold or damp weather, the use of the recirculation mode will cause windows to fog on the inside because of moisture buildup inside the vehicle. F...

  • Page 272

    Manual climate controls with touchscreen — if equipped hard-keys the hard-keys are located below the radio touchscreen. Soft-keys soft-keys are accessible on the radio touchscreen. Climate controls — hard-keys temperature controls — soft-keys 270 understanding your instrument panel.

  • Page 273

    Button descriptions (applies to both hard-keys and soft-keys) 1. Max a/c button press and release to toggle between max a/c and the prior settings. The soft-key illuminates when max a/c is on. In max a/c, the blower level and mode position can be adjusted to desired user settings. Pressing other set...

  • Page 274

    5. Defrost button press and release this button to turn on the rear window defroster (if equipped) and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 10 minutes. Caution! Failure to ...

  • Page 275

    • bi-level mode air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Note: bi-level mode is designed under comfort con- ditions to provide cooler air out of the panel outlets and warmer air from the fl...

  • Page 276

    Soft-key use the small blower icon to reduce the blower setting and the large blower icon to increase the blower setting. Blower can also be selected by pressing the blower bar area between the icons. 8. Climate control off button press and release this button to turn the climate control on/off. 9. ...

  • Page 277

    Automatic climate controls with touchscreen — if equipped hard-keys the hard-keys are located below the uconnect® screen. Soft-keys soft-keys are accessible on the uconnect® system screen. Automatic climate controls — hard-keys uconnect® 5.0 automatic temperature controls — soft-keys 4 understanding...

  • Page 278

    Button descriptions (applies to both hard-keys and soft-keys) 1. Max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manual mode and the max a/c indicator will tur...

  • Page 279

    5. Front defrost button press and release to change the current airflow setting to defrost mode. The indicator illuminates when this fea- ture is on. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level will increase. Use defrost mode wi...

  • Page 280

    7. Passenger temperature control up button provides the passenger with independent temperature control. Push the hard-key button for warmer tempera- ture settings or on the touchscreen, press and slide the soft-key temperature bar towards the red arrow soft-key for warmer temperature settings. Note:...

  • Page 281

    Soft-key use the small blower icon to reduce the blower setting and the large blower icon to increase the blower setting. Blower can also be selected by pressing the blower bar area between the icons. 11. Modes the airflow distribution mode can be adjusted so air comes from the instrument panel outl...

  • Page 282

    12. Climate control off button press and release this button to turn the climate control on/off. 13. Driver temperature control down button provides the driver with independent temperature con- trol. Push the hard-key button for cooler temperature settings or on the touchscreen, press and slide the ...

  • Page 283

    2. Next, adjust the temperature you would like the system to maintain by adjusting the driver and pas- senger temperature hard or soft control buttons. Once the desired temperature is displayed, the system will achieve and automatically maintain that comfort level. 3. When the system is set up for y...

  • Page 284

    Hard key a second time to turn off the recirculation mode led and allow outside air into the vehicle. Note: in cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (soft-key button greyed out) if conditions exist that could create...

  • Page 285

    Adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window fogging and frosting vehicle windows tend to fog on the inside of the glass in mild, rainy and/or humid weather. Windows may frost on the inside of the glass in very cold weather. To...

  • Page 286

    Operating tips chart 284 understanding your instrument panel.

  • Page 287: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .290 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .290 ▫ automatic transmission . . . . . . . . . . . . . . . .291 ▫ extreme cold weather (below –20°f or −29°c) . . . . . . . . . . . . . . . . .291 ▫ ...

  • Page 288

    ▫ electronically shifted transfer case (four-position switch) — if equipped . . . . . . .311 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . . .316 䡵 limited-slip differential . . . . . . . . . . . . .318 䡵 driving on slippery surfaces . . . . . . . . .318 ▫ acceleration . . . . . . . . ....

  • Page 289

    ▫ tire identification number (tin). . . . . . . . . . .344 ▫ tire terminology and definitions . . . . . . . . . .345 ▫ tire loading and tire pressure . . . . . . . . . . .346 䡵 tires — general information . . . . . . . .351 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .351 ▫ tire in...

  • Page 290

    䡵 fuel requirements . . . . . . . . . . . . . . . . . .376 ▫ 5.7l engines . . . . . . . . . . . . . . . . . . . . . . . . .376 ▫ 6.4l engine . . . . . . . . . . . . . . . . . . . . . . . . . .376 ▫ reformulated gasoline . . . . . . . . . . . . . . . . .377 ▫ gasoline/oxygenate blends . . . . . . . ....

  • Page 291

    ▫ operating tips . . . . . . . . . . . . . . . . . . . . . . .405 ▫ general maintenance . . . . . . . . . . . . . . . . . . .405 䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . . . .406 ▫ towing this vehicle behind another vehicle . . . .406 ▫ recreational towing — two...

  • Page 292

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Warnin...

  • Page 293

    Automatic transmission start the engine with the shift lever in the neutral or park position. Apply the brake before shifting into any driving range. Note: this vehicle is equipped with a transmission shift interlocking system. The brake pedal must be pressed to shift out of park. Tip start feature ...

  • Page 294

    Warning! • never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic tr...

  • Page 295

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. Gasoline engine only the engine block heater cord is routed through the...

  • Page 296

    Caution! (continued) • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting into any gear, make sure your foot is firmly pressing the brake pedal. Note: you must press and hold the brake pedal while shifting out of park. Warning! • it is dang...

  • Page 297

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 298

    Before the ignition switch can be turned to the full off (key removal) position. The key fob can only be re- moved from the ignition when the ignition is in the full off position, and the transmission is locked in park whenever the ignition switch is in the full off position. Note: if a malfunction ...

  • Page 299

    Self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers). Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped...

  • Page 300

    When parking on a hill, apply the parking brake before shifting the transmission to park, otherwise the load on the transmission locking mechanism may make it diffi- cult to move the shift lever out of park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away f...

  • Page 301

    Warning! (continued) • unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and ...

  • Page 302

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the off posi- tion to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ran...

  • Page 303

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 304

    If the transmission temperature exceeds normal operat- ing limits, the powertrain controller will modify the transmission shift schedule and expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating. If the transmission becomes extremely h...

  • Page 305

    In all cases, normal operation will resume once the transmission temperature has risen to a suitable level. Transmission limp home mode transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, transmission limp ho...

  • Page 306

    If the transmission cannot be reset, authorized dealer service is required. Electronic range select (ers) operation the electronic range select (ers) shift control allows the driver to limit the highest available gear when the shift lever is in the drive position. For example, if you shift the trans...

  • Page 307

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Note: to select the proper gear position for maximum deceleration (engine braking), simply press and hold the ers ...

  • Page 308

    Haul mode. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in tow/haul mode, transmission upshifts are delayed, and the trans- mission will automatically downshift (for engine brak- ing) during steady braking ma...

  • Page 309

    Torque converter clutch a feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati- cally at calibrated speeds. This may result in a slightly different feeling or response during normal operation i...

  • Page 310

    Manually shifted transfer case — if equipped the transfer case provides four mode positions. • two-wheel drive high range (2h) • four-wheel drive high range (4h) • neutral (n) • four-wheel drive low range (4l) this transfer case is intended to be driven in the 2h position for normal street and highw...

  • Page 311

    Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the drivetrain. Note: do not attempt to make a shift while only the front or rear wheels are spinning. The front a...

  • Page 312

    4h four-wheel drive high range — this range locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. Neutral (n) neutral — this range disengages the front and rear driveshafts from the pow...

  • Page 313

    2h or 4h to 4l with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift the transmission into neutral. While the vehicle is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position. Do not pause in transfer case neutral. Note: • pausing in transfer case n...

  • Page 314

    This electronically shifted transfer case provides four mode positions: • two-wheel drive high range (2wd) • four-wheel drive lock range (4wd lock) • four-wheel drive low range (4wd low) • neutral (neutral) this electronically shifted transfer case is designed to be driven in the two-wheel drive pos...

  • Page 315

    Note: the transfer case neutral position is selected by pressing the button located on the lower left hand corner of the 4wd control switch. The transfer case neutral position is to be used for recreational towing only. Refer to “recreational towing” in “starting and operating” for further informati...

  • Page 316

    After engine start up or illuminates during driving, it means that the four-wheel drive system is not function- ing properly and that service is required. Warning! Always engage the parking brake when powering down the vehicle if the “svc 4wd warning light” is illuminated. Not engaging the parking b...

  • Page 317

    Warning! (continued) disengages both the front and rear drive shafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle. For additional information on the appropriate use of ...

  • Page 318

    Shifting procedure note: • if any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The position indicator light for the previous posi- tion will remain on and the newly selected position indicator light will continue to flash until all t...

  • Page 319

    2wd or 4wd lock to 4wd low note: when shifting into or out of 4wd low some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants. Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped. You can use either of the fo...

  • Page 320

    To be operable. If the ignition switch is not in the on position, the shift will not take place and no position indicator lights will be on or flashing. Limited-slip differential the limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is...

  • Page 321

    Erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the rear (driving) wheels. Warning! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehi...

  • Page 322

    Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow- ing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicl...

  • Page 323

    Caution! (continued) • driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.E., engine oil, trans- mission, axle, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through stan...

  • Page 324

    If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these condi- tions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. Note: • increased noise levels at the end of ...

  • Page 325

    Caution! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the new vehicle limited warranty. Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from movi...

  • Page 326

    When the parking brake is applied with the ignition switch on, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime ...

  • Page 327

    The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously ...

  • Page 328

    Brake system if power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. However, you will experience a substantial increase in braking effort to stop the vehicle. If either the front or rear hydraulic system loses normal bra...

  • Page 329

    With a separate computer to modulate hydraulic pressure to prevent wheel lockup and help avoid skidding on slippery surfaces. The system’s pump motor runs during an abs stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal. The abs co...

  • Page 330

    Warning! (continued) • the anti-lock brake system (abs) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent c...

  • Page 331

    Anti-lock brake system (abs) the abs aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lockup and help avoid skidding on slippery surfaces during braking. Note: abs improves steering control of the vehicle d...

  • Page 332

    The wheel that is not spinning. This feature remains active even if tcs and esc are in the “partial off” mode. Refer to “electronic stability control (esc)” in this section of this manual. This brake pressure modulation transfers drive torque from slipping to non-slipping wheels to provide optimal f...

  • Page 333

    Warning! There may be situations on minor hills with a loaded vehicle or while pulling a trailer where the system will not activate and slight rolling may occur, which could cause a collision with another vehicle or object. Always remember the driver is responsible for brak- ing the vehicle. The sys...

  • Page 334

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision w...

  • Page 335

    3. With the engine running and the brake applied, rotate the steering wheel 180° counterclockwise from center. 4. Press the “esc off” switch four times within 20 seconds. The “esc off indicator light” should appear and disappear four times. 5. Rotate the steering wheel 360° clockwise (180° clock- wi...

  • Page 336

    The intended path, esc applies the brake of the appro- priate wheel to assist in counteracting the oversteer or understeer condition. • oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • understeer - when the vehicle is turning less than appropriate for ...

  • Page 337

    4wd lock or 4wd auto, the esc system will be in this mode. This mode should be used for almost all driving situations. Esc should only be turned to “partial off” or “esc off” for specific reasons as noted below. Esc partial off this mode is entered by momentarily pressing the “esc off” switch. When ...

  • Page 338

    Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the “esc off indicator light” will be illuminated. When in “partial off” mode, the engine power reduction feature of tcs is disabled, and t...

  • Page 339

    Note: the “esc off” message will display and the audible chime will sound when the shift lever is placed into the park position from any other position and then moved out of the park position. This will occur even if the message was previously cleared. In this mode, esc and tcs except for the “limit...

  • Page 340

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is turned to the on position. It should go out with the engine running. If the “esc activation/malfunction indicator...

  • Page 341

    • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation. The “esc off indicator light” indicates the electronic stability control (esc) is partially off. Trailer sway...

  • Page 342

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 343

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 344

    Example: r = construction code — ⬙r⬙ means radial construction — ⬙d⬙ means diagonal or bias construction 15 = rim diameter in inches (in) service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of spee...

  • Page 345

    Example: load identification: ⴖ....Blank....ⴖ = absence of any text on the sidewall of the tire indicates a standard load (sl) tire extra load (xl) = extra load (or reinforced) tire light load (ll) = light load tire c, d, e, f, g = load range associated with the maximum load a tire can carry at a sp...

  • Page 346

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 347

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 348

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. B-pillar location for tire and loading information placard 346 starting and operating.

  • Page 349

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 350

    To determine the maximum loading conditions of your vehicle, locate the statement “the combined weight of occupants and cargo should never exceed xxx lbs or xxx kg” on the tire and loading information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) ...

  • Page 351

    Note: • if your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. The follow- ing table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and num- ber and size of occupan...

  • Page 352

    350 starting and operating.

  • Page 353

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 354

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear pat- terns...

  • Page 355

    Tire inflation pressures the proper cold tire inflation pressure is listed on the driver’s side b-pillar or rear edge of the driver’s side door. At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judge- ment when determining p...

  • Page 356

    Inflation pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too ...

  • Page 357

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than ¼⬙ (6 mm). Consult an authorized...

  • Page 358

    Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Snow tires some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a mountain/snowflake symbol on the tire sidewall. If you need sn...

  • Page 359

    See the tire pressure monitoring section for more infor- mation. Spare tires — if equipped note: for vehicles equipped with tirefit instead of a spare tire, please refer to “tirefit kit” in “what to do in emergencies” for further information. Caution! Because of the reduced ground clearance, do not ...

  • Page 360

    Since this tire has limited tread life, the original equip- ment tire should be repaired (or replaced) and reinstalled on your vehicle at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically f...

  • Page 361

    Your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than ...

  • Page 362

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 363

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 364

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 365

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. Please follow the table below for proper ...

  • Page 366

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 367

    Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation are...

  • Page 368

    Dual rear wheels the tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. Caution! 4500/5500 dual rear tires may only have one ap- ...

  • Page 369

    Tire pressure monitor system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the outsi...

  • Page 370

    To be driven for up to 20 minutes above 15 mph (25 km/h) in order for the tpms to receive this informa- tion. For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kpa). If the ambient temperature is 68°f (20°c) and the measured tire...

  • Page 371

    Note: • the tpms is not intended to replace normal tire care and maintenance or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat a...

  • Page 372

    The matching full size spare wheel and tire assembly (if equipped) has a tpm sensor. The matching full size spare can be used in place of any of the four road tires. The tpms will only monitor the pressure in the full size spare when it is used in place of a road tire. Otherwise, a spare with a pres...

  • Page 373

    Tire pressure monitoring low pressure warnings the “tire pressure monitoring telltale light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the evic will display a “low tire pressure” message for a...

  • Page 374

    Will automatically update, the graphic display in the evic will stop flashing or return to it’s original color, and the “tire pressure monitoring telltale light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this informa...

  • Page 375

    System ⬙ message will no longer display, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installin...

  • Page 376

    Tire pressure information system (tpis) chassis cab — if equipped your vehicle may be equipped with a tire pressure information system (tpis). The tire pressure information system (tpis) uses wire- less technology with wheel rim mounted electronic sen- sors to transmit tire pressure levels. Sensors ...

  • Page 377

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the ⬙service tpm system⬙ message will no longer be displayed, and a pressure value will display in place of the dashes. A system fault can occur due to any of t...

  • Page 378

    Fuel requirements 5.7l engines this engine is designed to meet all emis- sions regulations and provide satisfactory fuel economy and performance when us- ing high quality unleaded gasoline having an octane range of 87 to 89. The manufac- turer recommends the use of 89 octane for optimum performance....

  • Page 379

    Use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline”. Reformulated gasolines contain oxygenates and are...

  • Page 380

    E-85 usage in non-flex fuel vehicles non-flex fuel vehicles (ffv) are compatible with gaso- line containing 10% ethanol (e10). Gasoline with higher ethanol content may void the new vehicle limited warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all...

  • Page 381

    Therefore, you should ask your gasoline retailer whether the gasoline contains mmt. Mmt is prohibited in federal and california reformulated gasoline. Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or ...

  • Page 382

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the respon...

  • Page 383

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel caution! • damage to the fuel system...

  • Page 384

    Note: tighten the gas cap ¼ turn until you hear one click. This is an indication that the cap is properly tightened. If the gas cap is not tightened properly, the malfunction indicator light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. Warning! A fire may result...

  • Page 385

    Included on this label and indicates the month, day and hour of manufacture. The bar code that appears on the bottom of the label is your vin. Gross vehicle weight rating (gvwr) the gvwr is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo. The lab...

  • Page 386

    Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a comm...

  • Page 387

    Trailer towing in this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain the new vehicle limited war...

  • Page 388

    Evenly. Make sure that you do not exceed either front or rear gawr. Refer to “vehicle loading/vehicle certifica- tion label” in “starting and operating” for further information. Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result i...

  • Page 389

    Weight-distributing hitch a weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s direc...

  • Page 390

    Gooseneck hitch the gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer hitch classification the following chart provides the industry standard for th...

  • Page 391

    Trailer towing weights (maximum trailer weight ratings) chassis cab 3500 st/slt/laramie 5.7l hemi® 6-speed automatic transmission towing: 14,050 lbs (6 372 kg) payload: 4,728 lbs (2 144 kg) 6.4l hemi® 6-speed automatic transmission towing: 17,850 lbs (8 096 kg) payload: 8,013 lbs (3 634 kg) 6.7l cum...

  • Page 392

    Chassis cab 4500 st/slt/laramie 6.4l hemi® 6-speed automatic transmission towing: 18,950 lbs (8 595 kg) payload: 9,134 lbs (4 143 kg) 6.7l cummins® turbo diesel 6-speed manual trans- mission towing: 20,200 lbs (9 162 kg) payload: 7,391 lbs (3 352 kg) 6.7l cummins® turbo diesel 6-speed aisin automati...

  • Page 393

    Note: for additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http://www.Ramtrucks.Com. • http://www.Ramtruck.Ca (canada). Trailer and tongue weight always load a trailer with 60% of the weight in the front of the trailer. This places ...

  • Page 394

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to “tire safety information/tire and loading in- formation placard” i...

  • Page 395

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 396

    Warning! (continued) 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch utilized. Towing requirements — tires • do not attempt to tow a trailer while using a compact spare tire. • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to...

  • Page 397

    • an electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • trailer brakes are recommended for trailers over...

  • Page 398

    Note: this module has been designed and verified with electric trailer brakes and new electric over hydrau- lic systems. Some previous eoh systems may not be compatible with itbm. Integrated trailer brake module (itbm) 1 — gain adjustment button 2 — gain adjustment button 3 — manual brake control le...

  • Page 399

    The user interface consists of the following: manual brake control lever slide the manual brake control lever to the right to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes. If the manual brake control lever is activated while the brake is also applied, the g...

  • Page 400

    Adjusting gain note: this should only be performed in a traffic free environment at speeds of approximately 20–25 mph (30–40 km/h). 1. Make sure the trailer brakes are in good working condition, functioning normally and properly ad- justed. See your trailer dealer if necessary. 2. Hook up the traile...

  • Page 401

    9. If the trailer wheels lockup (indicated by squealing tires), reduce the gain setting; if the trailer wheels turn freely, increase the gain setting. Repeat steps 8 and 9 until the gain setting is at a point just below trailer wheel lockup. If towing a heavier trailer, trailer wheel lockup may not ...

  • Page 402

    Caution! Connecting a trailer that is not compatible with the itbm system may result in reduced or complete loss of trailer braking. There may be a increase in stop- ping distance or trailer instability which could result in damage to your vehicle, trailer, or other property. Warning! Connecting a t...

  • Page 403

    Warning! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automo- tive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. Towing tips before setting out on a trip, practice turni...

  • Page 404

    Note: check the automatic transmission fluid level before towing. Tow/haul mode to reduce potential for automatic transmission overheat- ing, turn the “tow/haul” feature on when driving in hilly areas, or select a lower gear range (using the electronic range select (ers) switches) on more severe gra...

  • Page 405

    Note: before installation of a snowplow it is highly recommended that the owner/installer obtain and follow the recommendations contained within the current ram body builders guide. See your authorized dealer, in- staller or snowplow manufacturer for this information. There are unique electrical sys...

  • Page 406

    Snowplow prep package model availability for information about snowplow applications visit www.Ramtrucks.Com or refer to the current ram body builders guide. 1. The maximum number of occupants in the truck should not exceed two. 2. The total gvwr or the front gawr or the rear gawr should never be ex...

  • Page 407

    Completely and position it as low as road or surface conditions permit. Do not exceed 40 mph (64 km/h). The operator should always maintain a safe stopping distance and allow adequate passing clearance. Operating tips under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating ...

  • Page 408

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models flat tow none not allowed see instructions • automatic transmission in park • manual transmission in gear (not in neutral) • t...

  • Page 409

    Recreational towing — two-wheel drive models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is allowed only if the rear wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly...

  • Page 410

    Recreational towing — four-wheel drive models note: both the manual shift and electronic shift trans- fer cases must be shifted into neutral (n) for recre- ational towing. Automatic transmissions must be shifted into park for recreational towing. Manual transmissions must be placed in gear (not in n...

  • Page 411

    Caution! (continued) • do not disconnect the rear drive shaft because fluid will leak from the transfer case, causing damage to internal parts. • do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Shifting into neutral (n) use the following procedure t...

  • Page 412

    3. Press and hold the brake pedal. 4. Depress the clutch pedal on a manual transmission. 5. If the transfer case is in 4wd auto (if equipped), press a selector button or rotate the selector switch to shift the transfer case into the 2wd or 4wd lock position. • with manual shift transfer case, shift ...

  • Page 413

    12. Turn the ignition switch to the off position, and remove the key fob. 13. Attach the vehicle to the tow vehicle using a suitable tow bar. 14. Release the parking brake. Note: with electronic shift transfer case: • the transfer case cannot be shifted into neutral (n) from the 4wd auto position (i...

  • Page 414

    5. Shift the transmission into neutral. • with manual shift transfer case, shift the transfer case lever to the desired position. • with electronic shift transfer case, press and hold the transfer case neutral (n) button until the neu- tral (n) indicator light turns off. After the neu- tral (n) indi...

  • Page 415

    • the ignition switch must be in the on/run position for a shift to take place and for the position indicator lights to be operable. If the ignition switch is not in the on/run position, the shift will not take place and no position indicator lights will be on or flashing. • a flashing neutral (n) p...

  • Page 417: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .416 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .416 ▫ torque specifications . . . . . . . . . . . . . . . . . .416 䡵 jacking and tire changing . . . . . . . . . .419 ▫ 4500/5500 mo...

  • Page 418

    Hazard warning flashers the hazard warning flasher switch is located on the upper switch bank just below the radio. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Pre...

  • Page 419

    Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Note: dual wheels are flat mounted, center piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the int...

  • Page 420

    After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may ...

  • Page 421

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 422

    Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Turn on the hazard warning flasher. 3. Set the parking brake. 4. Place the shift lever into par...

  • Page 423

    Jacking instructions instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher....

  • Page 424

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. If equipped, remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them cou...

  • Page 425

    When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Securely place the jack under the sway bar bracket (unless both tires are flat on one side, then place jack under shock bracket) facing forward in vehicle. Connect the jack tube ext...

  • Page 426

    (srw) models. On dual rear wheel models (drw) the lug nuts are a two-piece assembly with a flat face. Lightly tighten the nuts. To avoid risk of forcing the vehicle off the jack, do not fully tighten the nuts until the vehicle has been lowered. 6. Using the wheel wrench, finish tightening the nuts u...

  • Page 427

    Caution! Use extreme caution when removing the front and rear center caps. Damage can occur to the center cap and/or the wheel if screwdriver type tools are used. A pulling motion, not a pry off motion, is recom- mended to remove the caps. For single rear wheel (srw) models, use the flat blade on th...

  • Page 428

    Replace the wheel skins first using a rubber mallet. When replacing the hub caps, tilt the cap retainer over the lug nut bolt circle and strike the high side down with a rubber mallet. Be sure that the hub caps and wheel skins are firmly seated around the wheel. Dual rear wheels slots in the wheels ...

  • Page 429

    Hoisting a conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking loca- tions. However, a floor jack or frame hoist must never be used on any other parts of the underbody. Caution! Never use a floor jack directly under the differential housing of a load...

  • Page 430

    Note: the positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan bla...

  • Page 431

    3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-start...

  • Page 432

    Warning! Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electri- cal spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts. 5. Start the engine in t...

  • Page 433

    Caution! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prev...

  • Page 434

    Caution! • when “rocking” a stuck vehicle by shifting be- tween drive/2nd gear and reverse, do not spin the wheels faster than 15 mph (24 km/h), or drive- train damage may result. • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damag...

  • Page 435

    Emergency tow hooks — if equipped your vehicle may be equipped with emergency tow hooks. Note: for off-road recovery, it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle. Warning! • do not use a chain for freeing a stuck vehicle. Chains may break, causi...

  • Page 436

    Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use the following procedure to temporarily move the shift lever: 1. Turn the engine off. 2. Firmly apply the parking brake. 3. Tilt the steering wheel to the full up position. 4. Press ...

  • Page 437

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the trans- mission and drivetrain are operable, disabled vehicles may also be towed as described under “recreational towing” in the “starting and operating” section. Towin...

  • Page 438

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 439

    If the transmission is not operable, or the vehicle must be towed faster than 30 mph (48 km/h) or farther than 15 miles (24 km), tow with the rear wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed, or with the front wheels raised and the rear wheels on a towing dolly, or ...

  • Page 440

    Caution! • front or rear wheel lifts must not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when towing. • towing this vehicle in violation of the above re- quirements can cause severe transmission and/or transfer case damage. Damage f...

  • Page 441: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 5.7l . . . . . . . . . .441 䡵 engine compartment — 6.4l . . . . . . . . . .442 䡵 onboard diagnostic system (obd ii) . . .443 ▫ loose fuel filler cap message . . . . . . . . . . . .443 䡵 emissions inspection and maintenance programs . . . . . ....

  • Page 442

    ▫ cooling system . . . . . . . . . . . . . . . . . . . . . .457 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .465 ▫ rear axle and 4x4 front driving axle fluid level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467 ▫ transfer case . . . . . . . . . . . . . . . . . . . . ...

  • Page 443

    Engine compartment — 5.7l 1 — air cleaner filter 6 — battery 2 — automatic transmission dipstick 7 — washer fluid reservoir 3 — engine oil fill 8 — power distribution center (fuses) 4 — engine oil dipstick 9 — coolant pressure cap 5 — brake fluid reservoir 10 — engine coolant reservoir 7 maintaining...

  • Page 444

    Engine compartment — 6.4l 1 — coolant pressure bottle 6 — battery 2 — transmission dipstick 7 — power distribution center (fuses) 3 — engine oil fill 8 — washer solvent 4 — engine oil dipstick 9 — power steering fluid reservoir 5 — brake fluid reservoir 10 — air cleaner filter 442 maintaining your v...

  • Page 445

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 446

    “understanding your instrument panel” for further in- formation. Tighten the fuel filler cap properly and press the select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap...

  • Page 447

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 448

    Available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! Y...

  • Page 449

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 450

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for further informa- tion. Note: under no circumstances should oil change in- tervals exceed 10,000 miles (16,000 km) or twelve mon...

  • Page 451

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity — 5.7l engine mopar sae 5w-20 engine oil or equivalent pennzoil® or shell helix® is recommended for all operating tem-...

  • Page 452

    Synthetic engine oils you may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Disposing of used engine oil and oil filters care should be taken in disposing of used engine oil ...

  • Page 453

    Warning! (continued) for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury. Engine air cleaner filter selection the quality o...

  • Page 454

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 455

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 456

    Underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant, such as mopar® lock cylinder lubricant directly...

  • Page 457

    To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Warning! Commercially available windshield washer solvents are flamma...

  • Page 458

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 459

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 460

    Warning! (continued) to cool. Never try to open a cooling system pressure cap when the radiator is hot. Engine coolant checks check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rust...

  • Page 461

    Reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old engine coolant (antifreeze). Refer to the “maintenance schedule” for the proper maintenance intervals. Selection of coolant refer to “fluids, lubricants, and genuine parts” i...

  • Page 462

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 463

    (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area whe...

  • Page 464

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 465

    2. Lift and remove the plastic dipstick from the reservoir neck. 3. Check the coolant level on the dipstick. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing en- gine coolant (antif...

  • Page 466

    Of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Checking coolant level — 6.4l eng...

  • Page 467

    • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (anti- freeze) needs to be added, the contents of the coolant expansion bottle must also be protected against freez- ing. • if frequent engine coolant (antifreeze) additions are required, the cool...

  • Page 468

    Warning! (continued) high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency. Brake fluid level check the fluid level of the master cylinder should be checked when performing under the hood service or immediately if the...

  • Page 469

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 470

    When checking the fluid level (4500/5500 only), the vehicle should be in a level position. The fluid level should be ¼ in ± ¼ in (6.4 mm ± 6.4 mm) below the fill hole on the front axle. The fluid level should be level with the bottom of the fill hole on the rear axle. Drain and refill on 4500/5500 v...

  • Page 471

    Lubricant selection refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Note: the presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encount...

  • Page 472

    Automatic transmission — aisin f21-250 hd transmission — if equipped selection of lubricant it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “fluids, lubricants, and genuine pa...

  • Page 473

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check check the fluid level when the engine is fully warmed up and the transmission fluid is at normal ope...

  • Page 474

    5. Place the shift lever momentarily into each gear posi- tion (allowing time for the transmission to fully en- gage in each position), ending with the transmission in park. 6. Wipe the area around the dipstick clean to prevent dirt from entering the transmission. 7. Remove the dipstick, wipe it cle...

  • Page 475

    Caution! If the fluid temperature is below 50°f (10°c) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. Run the engine at idle, in park, to warm the fluid. 9. Check for leaks. Release the parking brake. Note: to prevent di...

  • Page 476

    Extreme hot or cold weather and other extreme condi- tions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Cor...

  • Page 477

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 478

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar® wheel cleaner. Note: if your vehicle is equipped with dark ...

  • Page 479

    • for tough stains, apply mopar® total clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar® multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap resid...

  • Page 480

    Caution! Do not use alcohol and alcohol-based and/or keton based cleaning products to clean leather seats, as damage to the seat may result. Cleaning headlights your vehicle is equipped with plastic headlights and fog lights that are lighter and less susceptible to stone break- age than glass headli...

  • Page 481

    1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft cloth. Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleane...

  • Page 482

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Power distribution center the power distribution center is located in the engine compart...

  • Page 483

    Cavity cartridge fuse micro fuse description f05 40 amp green compressor for air suspension – if equipped f06 40 amp green antilock brakes/electronic stability control pump f07 40 amp green starter solenoid f08 40 amp green (gas & cummins diesel) 20 amp yellow (1500 ld diesel) emissions diesel – if ...

  • Page 484

    Cavity cartridge fuse micro fuse description f10 50 amp red body controller / exterior lighting #2 – if equipped with stop/start f11 30 amp pink integrated trailer brake module – if equipped f12 40 amp green body controller #3 / interior lights f13 40 amp green blower motor f14 40 amp green body con...

  • Page 485

    Cavity cartridge fuse micro fuse description f26 30 amp pink antilock brakes/stability control module/ valves f28 20 amp yellow trailer tow backup lights – if equipped f29 20 amp yellow trailer tow parking lights – if equipped f30 30 amp pink trailer tow receptacle f32 30 amp pink drive train contro...

  • Page 486

    Cavity cartridge fuse micro fuse description f39 30 amp pink vehicle system interface module #1– if equipped f41 10 amp red active grill shutter f42 20 amp yellow horn f43 10 amp red snow plow (left) – if equipped f44 10 amp red diagnostic port f46 10 amp red tire pressure monitor f47 10 amp red sno...

  • Page 487

    Cavity cartridge fuse micro fuse description f56 15 amp blue additional diesel content – if equipped f57 20 amp yellow transmission f58 20 amp yellow (gas engine) / 25 amp natural (cummins diesel engine) engine cooling pump f60 15 amp blue underhood lamp f61 20 amp yellow power take-off unit – if eq...

  • Page 488

    Cavity cartridge fuse micro fuse description f67 10 amp red cd / dvd / bluetooth hands-free module – if equipped f69 15 amp blue mod scr 12v (cummins diesel) – if equipped f70 30 amp green fuel pump motor f71 25 amp natural amplifier f72 10 amp red voltage stabilizer modules – if equipped f74 20 amp...

  • Page 489

    Cavity cartridge fuse micro fuse description f78 10 amp red engine control module / electric power steer- ing f79 15 amp blue clearance lights f80 10 amp red universal garage door opener / compass f81 20 amp yellow trailer tow right turn/stop lights f82 10 amp red steering column control module/ cru...

  • Page 490

    Cavity cartridge fuse micro fuse description f94 10 amp red shifter / transfer case module f95 10 amp red rear camera / park assist f96 10 amp red rear seat heater switch f97 25 amp natural rear heated seats & heated steering wheel – if equipped f98 25 amp natural front heated seats – if equipped f9...

  • Page 491

    Caution! • when installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • when replacing a blown fuse,...

  • Page 492

    Light bulbs — interior bulb number overhead console lamps ts 212-2 dome lamp 7679 for lighted switches, see your authorized dealer for replacement instructions. Light bulbs — exterior bulb number quad headlamp – low beam h11 quad headlamp – high beam 9005 quad headlamp – front turn signal lamp 3157n...

  • Page 493

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Base quad / premium bi-halogen: low...

  • Page 494

    7. Reach into the front wheel house ahead of the front wheel, remove the fastener, and lift the cover over the access hole in the front of the wheel house splash shield. Access to the rear of the lamp can be gained through this access hole. 8. Reach through the access hole of the wheel house splash ...

  • Page 495

    11. Replace bulb(s) as necessary. Caution! • do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • always use the correct bulb size and type for replacement. An incorrect bulb size or type may overheat ...

  • Page 496

    Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. Center high-mounted stoplamp (chmsl) with cargo lamp 1. Remove the two screws holding the housing/lens to the body as shown. Chmsl mounting s...

  • Page 497

    2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn the desired bulb socket ¼ turn and remove the socket and bulb from housing. 4. Pull the desired bulb straight from the socket. Chmsl connector location chmsl bulb and socket 7 maintaining your vehicle 495.

  • Page 498

    Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • outside bulbs: cargo lamps • inside bulb: center high-mounted stop lamp 5. Reverse the procedure for installation of bulbs and housing. Cab...

  • Page 499

    2. Rotate the bulb socket ¼ turn and pull it from the lamp assembly. 3. Pull the bulb straight from it’s socket and replace. Removing bulb socket from clearance lamp removing the bulb from the bulb socket 7 maintaining your vehicle 497.

  • Page 500

    Fluid capacities u.S. Metric fuel (approximate) standard rear tank 52 gallons 197 liters optional midship tank 22 gallons 83 liters engine oil with filter 5.7l engine (sae 5w-20, api certified) 7 quarts 6.6 liters 6.4l engine (sae 0w-40, synthetic api certified) 7 quarts 6.6 liters cooling system 5....

  • Page 501

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10–year/150,000 mile formula oat (organic additive technology). Engine oil – 5.7l engine we recommend you use api certified sae 5w-20 engine oil, meet...

  • Page 502

    Component fluid, lubricant, or genuine part engine oil – 6.4l engine for best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet the american petroleum institute (api) categories of sn. The manufac- turer ...

  • Page 503

    Chassis component fluid, lubricant, or genuine part automatic transmission (5.7l, and 6.4l engine with 66rfe transmission) (for diesel en- gine see diesel supplement) we recommend you use mopar® atf+4® automatic transmission fluid or equivalent licensed atf+4® product. Failure to use atf+4® fluid ma...

  • Page 505: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .504 ▫ maintenance chart . . . . . . . . . . . . . . . . . . .506 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 506

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indi- cator message will illuminate. Th...

  • Page 507

    • check the tire inflation pressures and look for unusual wear or damage • check the fluid levels of the coolant reservoir, brake master cylinder, power steering and automatic trans- mission as needed • check function of all interior and exterior lights required maintenance refer to the maintenance ...

  • Page 508

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176...

  • Page 509

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 510

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 511

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 512

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 513

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 515: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .515 ▫ prepare for the appointment. . . . . . . . . . . . .515 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .515 ▫ be reasonable with requests ....

  • Page 516

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .521 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .521 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .521 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .522 514 if...

  • Page 517

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 518

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 519

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 520

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 521

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 522

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 523

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 524

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 525: Index

    Index 10

  • Page 526

    Adding engine coolant (antifreeze) . . . . . . . . . . . .460 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .381 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .379 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . . .164 airbag. . . . . . . ....

  • Page 527

    Special additives . . . . . . . . . . . . . . . . . . . . . . .470 axle fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467 axle lubrication (axle fluid) . . . . . . . . . . . . . . . . .467 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 keyless transmi...

  • Page 528

    Check engine light (malfunction indicator light) . .196 checking your vehicle for safety . . . . . . . . . . . . . .109 checks, safety . . . . . . . . . . . . . . . . . . . . . . . . . . .109 child restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 cigar lighter . . . . . . . . . . ...

  • Page 529

    Dipsticks automatic transmission . . . . . . . . . . . . . . . . . .471 power steering . . . . . . . . . . . . . . . . . . . . . . . . .322 disabled vehicle towing . . . . . . . . . . . . . . . . . . . .435 disposal antifreeze (engine coolant) . . . . . . . . . . . . . . . .462 door locks . . . . . ...

  • Page 530

    Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .447 oil filler cap . . . . . . . . . . . . . . . . . . . . . . . . . .449 oil selection . . . . . . . . . . . . . . . . . . . . . . . . . . .448 oil synthetic . . . . . . . . . . . . . . . . . . . . . . . . . .450 engine oil visc...

  • Page 531

    Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . .379 clean air . . . . . . . . . . . . . . . . . . . . . . . . . . . . .377 ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .377 filler cap (gas cap) . . . . . . . . . . . . . . . . . . . . .382 filter . . . . . . . ...

  • Page 532

    High beam/low beam select switch . . . . . . . . .159 passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 head restraints . . . . . . . . . . . . . . . . . . . . . . . . . .139 heated mirrors . . . . . . . . ....

  • Page 533

    Key, replacement . . . . . . . . . . . . . . . . . . . . . . . . . .19 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 key, sentry (immobilizer) . . . . . . . . . . . . . . . . . . . .18 lane change and turn signals . . . . . . . . . . . . . . . .158 lane change assist ....

  • Page 534

    Instrument cluster . . . . . . . . . . . . . . . . . . . . . .196 interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 oil pressure . . . . . . . . . . . . . . . . . . . . . . . . . . .201 passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 seat belt reminder . ...

  • Page 535

    Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . .130 modifications/alterations, vehicle . . . . . . . . . . . . . . .7 monitor, tire pressure sy...

  • Page 536

    Passing light . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 pedals, adjustable. . . . . . . . . . . . . . . . . . . . . . . . .164 personal settings. . . . . . . . . . . . . . . . . . . . . . . . . .234 pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 pets, ...

  • Page 537

    Remote sound system (radio) controls . . . . . . . . .262 remote starting system. . . . . . . . . . . . . . . . . . . . . .32 replacement keys . . . . . . . . . . . . . . . . . . . . . . . . .19 replacement parts. . . . . . . . . . . . . . . . . . . . . . . . .445 replacement tires . . . . . . . . ....

  • Page 538

    Sentry key replacement . . . . . . . . . . . . . . . . . . . . .19 service assistance . . . . . . . . . . . . . . . . . . . . . . . . .515 service contract . . . . . . . . . . . . . . . . . . . . . . . . . .517 service manuals . . . . . . . . . . . . . . . . . . . . . . . . . .520 settings, personal...

  • Page 539

    Storage compartment, center seat . . . . . . . . . . . . .184 storage, vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . .282 storing your vehicle . . . . . . . . . . . . . . . . . . . . . . .489 supplemental tire pressure information . . . . . . . . .362 sway control, trailer. . . . . . . ...

  • Page 540

    Torque converter clutch . . . . . . . . . . . . . . . . . . . .307 tow hooks, emergency . . . . . . . . . . . . . . . . . . . . .433 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .385 disabled vehicle . . . . . . . . . . . . . . . . . . . . . . . .435 guide . . . . . . . . . ....

  • Page 541

    Vehicle loading . . . . . . . . . . . . . . . . . . . . . . . . . .347 vehicle modifications/alterations . . . . . . . . . . . . . . .7 vehicle storage . . . . . . . . . . . . . . . . . . . . . . . . . . .282 viscosity, engine oil . . . . . . . . . . . . . . . . . . . . . . .449 warning lights (inst...

  • Page 542

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 543

    P r o m a s t e r chrysler group llc o w n e r ’ s m a n u a l 2 0 1 4 2014 promaster 14vf-126-aa first edition printed in u.S.A..