1. DL manuals
  2. RAM
  3. Automobile
  4. CHASSIS CAB 2015
  5. Owner's Manual

RAM CHASSIS CAB 2015 Owner's Manual

Summary of CHASSIS CAB 2015

  • Page 1

    C h a s s i s c a b o w n e r ’ s m a n u a l 2 0 1 5 2015 chassis cab 15dd43-126-ae fifth edition printed in u.S.A. Fca us llc.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .4 䡵 warnings and cautions . . . . . . . . . . . . . .6 䡵 van conversions/campers . . . . . . . . . . . .6 䡵 vehicle identification number . . . . . . . .6 䡵 vehic...

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engine...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importan...

  • Page 9

    Frame and underbody as well as the automobile infor- mation disclosure label affixed to a window on your vehicle, the vehicle registration and title. Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seri...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ wireless ignition node (win) . . . . . . . . . . . . .12 ▫ keyless push button ignition— if equipped. . . .13 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ removing k...

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . .27 ▫ programming additional transmitters. . . . . . . .28 ▫ transmitter battery replacement . . . . . . . . . . .28 ▫ general information . . . . . . . . . . . . . . . . . . . .31 䡵 remote starting system — if equipped .32 ▫ how to use remot...

  • Page 13

    䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . .106 ▫ transporting passengers . . . . . . . . . . . . . . . . .106 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .107 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 14

    A word about your keys your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a bladed key with an immobilizer chip in it, or a key fob with remote keyless entry (rke) transmitter and an ignition node module (ignm). The key...

  • Page 15

    Keyless push button ignition— if equipped this feature allows the driver to operate the ignition switch with the push of a button as long as the remote keyless entry (rke) transmitter is in the passenger compartment. The keyless push button ignition has four operating positions; three of which are l...

  • Page 16

    Key fob key fob — if equipped the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores i...

  • Page 17

    Keyless push button ignition key fob — if equipped this keyless push button ignition key fob allows the driver to operate the ignition switch with the push of a button, as long as the remote keyless entry (rke) transmitter is in the passenger compartment. The keyless push button ignition has four op...

  • Page 18

    Note: you can insert the double-sided emergency key into the door lock cylinder with either side up. Removing key fob from ignition place the shift lever in park (if equipped with an automatic transmission). Turn the key fob to the off position and then remove the key fob. Note: • the power window s...

  • Page 19

    • for vehicles equipped with a touchscreen radio, refer to “uconnect® settings” in “understanding your in- strument panel” for further information. Caution! • if your vehicle battery becomes low or dead, your key fob will become locked in the ignition. • do not attempt to remove the key fob while in...

  • Page 20

    Warning! (continued) mode. A child could operate power windows, other controls, or move the vehicle. • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove...

  • Page 21

    The system uses a key fob with a factory-mated remote keyless entry (rke) transmitter, an ignition node mod- ule, keyless push button ignition and a rf receiver to prevent unauthorized vehicle operation. Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the...

  • Page 22

    Replacement keys note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle. Caution! • always remove the key fobs from the vehicle and lock all doors when le...

  • Page 23

    Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Vehicle security alarm the vehicle security alarm monitors the vehicle doors and ignition for unauthorized operation. When the ve- hicle security al...

  • Page 24

    2. Perform one of the following methods to lock the vehicle: • push lock on the interior power door lock switch with the driver and/or passenger door open. • push the lock button on the exterior passive entry door handle with a valid key fob available in the same exterior zone (refer to ⬙keyless ent...

  • Page 25

    • for vehicles not equipped with keyless enter-n- go™, insert a valid key into the ignition switch and turn the key to the on position. The vehicle security alarm is designed to protect your vehicle. However, you can create conditions where the system will give you a false alarm. If one of the previ...

  • Page 26

    “dome on” position (rotate horizontal thumb wheel on the bottom of the switch to the far right detent position). The illuminated entry system will not operate if the dimmer control is in the “dome off” position (rotate horizontal thumb wheel on the bottom of the switch to the far left detent positio...

  • Page 27

    Remote unlock the doors push and release the unlock button on the rke transmitter once to unlock the driver’s door (if evic is setup for driver door first, otherwise this will unlock all doors), or push the unlock button twice within five key fob with remote keyless entry (rke) transmitter key fob w...

  • Page 28

    Seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote key unlock, driver door/all doors first this feature lets you program the system to unlock either the driver’s door or all doors on the first push o...

  • Page 29

    • for vehicles equipped with a touchscreen radio, refer to “uconnect® settings” in “understanding your in- strument panel” for further information. To lock the doors push and release the lock button on the rke transmit- ter to lock all doors. The turn signal lights will flash and the horn will chirp...

  • Page 30

    The panic alarm will stay on for three minutes unless you turn it off by either pushing the panic button a second time or drive the vehicle at a speed of 5 mph (8 km/h) or greater. Note: • the interior lights will turn off if you turn the ignition switch to the acc or on/run position while the panic...

  • Page 31

    2. Separating rke halves requires screw removal – if equipped, and gently prying the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. Emergency key removal emergency key removal 2 things to know before starting your vehicle 29.

  • Page 32

    Remove screw from transmitter case separating transmitter case 30 things to know before starting your vehicle.

  • Page 33

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the b...

  • Page 34

    Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. If your rke transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the transmitter. The expected ...

  • Page 35

    • battery at an acceptable charge level • rke panic button not pushed • fuel meets minimum requirement • system not disabled from previous remote start event • vehicle security alarm not active warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon ...

  • Page 36

    To enter remote start mode push and release the remote start button on the rke transmitter twice within five sec- onds. The parking lights will flash, vehicle doors will lock, and the horn will chirp twice (if programmed). Once the vehicle has started, the engine will run for 15 minutes. Note: • if ...

  • Page 37

    To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, push and release the unlock button on the rke transmitter to unlock the doors and disarm the vehicle security alarm system (if equipped). Then, prior to the end of the 15-minute cycle, cycle the ignition to the on...

  • Page 38

    Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed. The emergency key will unlock the driver door lock on your vehicle. Warning! • do not leave children or animals inside parked vehicles in hot weather. Inte...

  • Page 39

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the key fob in or near th...

  • Page 40

    Operate. A chime will sound if the key fob is in the ignition switch and a door is open, as a reminder to remove the key fob. Automatic door locks — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exce...

  • Page 41

    Child-protection door lock to provide a safer environment for children riding in the rear seat, the rear doors (if equipped) of your vehicle have the child-protection door lock system. To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to enga...

  • Page 42

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: • after setting the child-protection door lock system, always test the door from the inside to make certain it is in the des...

  • Page 43

    • if the vehicle is unlocked by the passive entry door handle, and no door goes ajar within 60 seconds, the vehicle will re-lock and if equipped will arm the security alarm. • the vehicles security alarm can be armed/disarmed by pushing the passive entry key fob lock/unlock buttons (if equipped). To...

  • Page 44

    To unlock from the passenger side: with a valid passive entry rke transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all doors automatically. The interior door panel lock knob will raise when the door is unlocked. Note: all doors will unlock ...

  • Page 45

    Do not grab the door handle when pushing the door handle lock button. This could unlock the door(s). Push the door handle button to lock do not grab the door handle when locking 2 things to know before starting your vehicle 43.

  • Page 46

    Note: • after pushing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • the pass...

  • Page 47

    The front passenger door for passenger window control and on the rear doors of the quad cab and crew cab models. The windows will operate when the ignition switch is turned to the on/run or acc position, and for up to 10 minutes after the ignition is turned off or until a front door is opened. Note:...

  • Page 48

    Auto-up feature with anti-pinch protection (4-door models driver and front passenger door only) — if equipped lift the window switch fully upward to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the auto up operation, push do...

  • Page 49

    Window lockout switch (4–door models only) the window lockout switch on the driver’s door allows you to disable the window control on the rear passenger doors. To disable the window controls on the rear passenger doors, push the window lock button into the latched or down position. To enable the win...

  • Page 50

    Open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sun- roof opening to minimize t...

  • Page 51

    Restraints or belt-positioning booster seats. Older chil- dren who do not use child restraints or belt- positioning booster seats should ride properly buckled up in a vehicle with a rear seat. 4. Never allow children to slide the shoulder belt behind them or under their arm. 5. You should read the i...

  • Page 52

    Seat belt systems buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and could cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can redu...

  • Page 53

    Beltalert may be triggered when an animal or heavy object is on the outboard front passenger seat or when the seat is folded flat (if equipped). It is recommended that pets be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts, and cargo is prop...

  • Page 54

    Warning! (continued) other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be serious...

  • Page 55

    Warning! (continued) it to your authorized dealer immediately and have it fixed. • a seat belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing inter- nal injuries. Always buckle your seat belt into the buckle nea...

  • Page 56

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the sea...

  • Page 57

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 58

    6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. First row center seat belt operating instructions (regular cab only) the firs...

  • Page 59

    2. Grasp the mini-latch plate and pull the seat belt over the seat. 3. Route the shoulder belt to the inside of the [right/ left] head restraint. Inserting latch plate in use position 2 things to know before starting your vehicle 57.

  • Page 60

    4. When the seat belt is long enough to fit, insert the mini-latch plate into the mini-buckle until you hear a “click.” 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. 6. When the seat belt is long enough to fit, ins...

  • Page 61

    Warning! (continued) • when reattaching the mini-latch plate and mini- buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding procedure to detach the mini-latch plate and mini- buckle, untwist the webbing, and reattach the mini-latch plate and mini-buckl...

  • Page 62

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 63

    Warning! • only use a seat belt extender if it is physically required in order to properly fit the original seat belt system. Do not use the seat belt extender if, when worn, the distance between the front edge of the seat belt extender buckle and the center of the occupant’s body is less than 6 inc...

  • Page 64

    The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately. Energy management feature — if equipped this vehicle has a seat belt system with an e...

  • Page 65

    If the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking regular cab quad cab®/me...

  • Page 66

    Sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occupant’s mid-section. Slide the latch plate into the buckle until you hear a ⬙click.⬙ in automatic locking mode, the...

  • Page 67

    Mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the seat belt assembly must be replaced if the switchable automatic locking retractor (alr) fea- ture or any other seat belt function is not working properly when checked according to the proce- dures in the service manual....

  • Page 68

    • seat belt pretenioners • seat belt buckle switch advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s advanced front air bag is mounted in the center of the steering wheel. The pass...

  • Page 69

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 70

    Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bags to inflate. • do not put anything on or around the air bag covers or attempt to op...

  • Page 71

    Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away f...

  • Page 72

    Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or all of the following may occur: • the air bag material may sometimes cause abrasions and/or skin reddening ...

  • Page 73

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • after any collision, the vehicle should be taken to an authorized dealer immediately. Enhanced accident response system in the event of an impact, if the communication network remains inta...

  • Page 74

    The orc monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the start or on/run position. If the ignition switch is in the off position or in the acc position, the air bag system is not on and the air bags will not inflate. The orc contains a backu...

  • Page 75

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. In this condition the air bags may not be ready to inflate for your protec- tion. Have an authorized dealer service the air bag system immediately. Warnin...

  • Page 76

    Warning! (continued) not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), t...

  • Page 77

    Note: edr data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the edr under normal driving conditions and no per- sonal data (e.G., name, gender, age, and crash location) are recorded. However, other parties, such as law en- forcement, could combin...

  • Page 78

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in...

  • Page 79

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 80

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 81

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 82

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 83

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 84

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 85

    Latch positions for installing child restraints in this vehicle regular cab • lower anchorage symbol – 2 anchorages per seating position • top tether anchorage symbol quad cab®/crew cab split bench • lower anchorage symbol - 2 anchorages per seating position • top tether anchorage symbol 2 things to...

  • Page 86

    Quad cab®/mega cab®/crew cab full bench • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 84 things to know before starting your vehicle.

  • Page 87

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 88

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 89

    Locating tether anchorages regular cab models have tether strap anchor- ages behind the front center and right seats. Quad cab, mega cab and crew cab models have tether strap anchorages located behind each of the rear seats. 1 — tether strap hook 2 — tether strap to child restraint 3 — tether anchor...

  • Page 90

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing child restraints...

  • Page 91

    Center seat latch — quad cab®/mega cab®/crew cab split bench if a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard latch anchors or seat bel...

  • Page 92

    3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 93

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 94

    Lap/shoulder belt systems for installing child restraints in this vehicle regular cab • alr = switchable automatic locking retractor • cinch = cinching latch plate • top tether anchorage symbol quad cab®/mega cab®/crew cab • alr = switchable automatic locking retractor • cinch = cinching latch plate...

  • Page 95

    Lap/shoulder belt systems what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for-...

  • Page 96

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 97

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 98

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 99

    Warning! (continued) (latch) restraint system” for the location of ap- proved tether anchorages in your vehicle. Regular and mega cab® trucks: in the regular cab truck, the top tether anchorages are located behind the center and right passenger seats. In the mega cab truck, the top tether anchorages...

  • Page 100

    2. Route the tether strap to provide the most direct path between the anchorage and the child seat. The tether strap should go between the head restraint posts underneath the head restraint. You may need to adjust the head restraint to the upward position to pass the tether strap underneath the head...

  • Page 101

    Warning! (continued) years or younger, including a child in a rear-facing child restraint. Quad cab® or crew cab trucks: the top tether anchorages in this vehicle are tether strap loops located between the rear glass and the back of the rear seat. There is a tether strap loop located behind each sea...

  • Page 102

    2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint, through the tether strap loop behind the seat and over to the tether strap loop behind the center seat. 3. Pass the tether strap hook under the head restraint behind...

  • Page 103

    4. Attach the hook to the center tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s instructions. Note: if there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connecte...

  • Page 104

    2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint, through the tether strap loop behind the seat and over to the tether strap loop behind either the right or left outboard seat. 3. Pass the tether strap hook under th...

  • Page 105

    4. Attach the hook to the outboard tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s instructions. Installing three child restraints: 1. Place a child restraint on each outboard rear seat. Route the tether straps following the directions for right a...

  • Page 106

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly (continued) warning! (continued) behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a spl...

  • Page 107

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 108

    • use the appropriate transmission gear to prevent engine lugging. • observe vehicle oil pressure and temperature indica- tors. • check the coolant and oil levels frequently. • vary throttle position at highway speeds when carry- ing or towing significant weight. Note: light duty operation such as l...

  • Page 109

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), whi...

  • Page 110

    Damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Safety checks you should make ...

  • Page 111

    Floor mat safety information always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in o...

  • Page 112

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 113: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 ▫ inside day/night mirror — if equipped . . . . .115 ▫ automatic dimming mirror — if equipped . . .115 ▫ automatic dimming mirror with rear view camera display — if equipped . . ....

  • Page 114

    ▫ 40-20-40 front bench seat — if equipped . . . .136 ▫ head restraints . . . . . . . . . . . . . . . . . . . . . .136 䡵 driver memory seat — if equipped . . . .140 ▫ programming the memory feature . . . . . . . . .141 ▫ linking and unlinking the remote keyless entry transmitter to memory . . . . . ....

  • Page 115

    ▫ flash-to-pass . . . . . . . . . . . . . . . . . . . . . . . .159 ▫ high/low beam switch . . . . . . . . . . . . . . . .159 䡵 windshield wipers and washers . . . . . .160 ▫ windshield wipers . . . . . . . . . . . . . . . . . . . .160 ▫ windshield wiper operation . . . . . . . . . . . . .160 ▫ inter...

  • Page 116

    䡵 power inverter — if equipped . . . . . . . .180 䡵 cupholders . . . . . . . . . . . . . . . . . . . . . . . .181 ▫ front seat cupholders (40–20–40 seats) . . . . . .181 ▫ front instrument panel cupholders — floor storage bin . . . . . . . . . . . . . . . . . . . . . . . . . .182 ▫ rear cupholders —...

  • Page 117

    Mirrors inside day/night mirror — if equipped a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror hea...

  • Page 118

    Left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you. Note: the automatic dimming mirror feature is dis- abled when the vehicle is in reverse gear to improve re...

  • Page 119

    Note: the assist and 9–1–1 features operate through the uconnect® access service. These buttons will only operate as long as your uconnect® access service is active. Refer to your “uconnect® system supplement manual” for further information. Assist call the assist button is used to automatically con...

  • Page 120

    3. Once a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 call system may transmit the following important vehicle information to a 9-1-1 operator: • indication that the occupant placed a 9-1-1 call. • the vehicle brand. • the last known gps coordinates of the vehicle. 4. You ...

  • Page 121

    Warning! (continued) electrical equipment to the vehicle’s electrical sys- tem. This may prevent your vehicle from sending a signal to initiate an emergency call. To avoid inter- ference that can cause the 9-1-1 call system to fail, never add aftermarket equipment (e.G., two-way mobile radio, cb rad...

  • Page 122

    Warning! • ignoring the rearview mirror light could mean you will not have 9-1-1 call services. If the rearview mirror light is illuminated, have an authorized dealer service the 9-1-1 call system immediately. • the occupant restraint control module turns on the air bag warning light on the instrume...

  • Page 123

    Note: never place anything on or near the vehicle’s wireless and gps antennas. You could prevent wireless and gps signal reception, which can prevent your vehicle from placing an emergency call. Wireless and gps signal reception is required for the 9-1-1 call system to function properly. General inf...

  • Page 124

    When the vehicle is placed into reverse gear a video display illuminates to display the image generated by the rear view camera. The auto dimming feature is also disabled to improve rear view viewing. Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent la...

  • Page 125

    Caution! It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location. Power mirrors — if equipped the controls for the power mirrors are located on the driver’s door trim panel. The power mirror controls consist of mirror selec...

  • Page 126

    To adjust a mirror, push either the l (left) or r (right) button to select the mirror that you want to adjust. Using the mirror control switch, push on any of the four arrows for the direction that you want the mirror to move. Power mirror controls 1 — mirror select buttons 2 — four-way mirror contr...

  • Page 127

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Refer to “rear window features” in “understanding the features of your vehicle” for further information. Illuminated vanity mirror —...

  • Page 128

    To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until the sun visor is in the desired position. Trailer towing mirrors — if equipped these mirrors are designed with an adjustable mirror head to provide a greater vision range...

  • Page 129

    Note: fold the trailer towing mirrors rearward prior to entering an automated car wash. A small blindspot mirror is located next to main mirror and can be adjusted separately. Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, ...

  • Page 130

    Driver’s power seat — if equipped some models may be equipped with an eight-way power driver’s seat. The power seat switches are located on the outboard side of the driver’s seat cushion. There are two power seat switches that are used to control the move- ment of the seat cushion and the seatback. ...

  • Page 131

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward. The seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 132

    Caution! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Tilting the seat up or down the angle of the seat cushion can be adjusted in fou...

  • Page 133

    The seat switch, the front of the seat cushion will move in the direction of the switch. Release the switch when you have reached the desired position. Power lumbar — if equipped vehicles equipped with power driver or passenger seats may be also be equipped with power lumbar. The power lumbar switch...

  • Page 134

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 135

    Vehicles equipped with remote start on models that are equipped with remote start, the heated seats can be programed to come on during a remote start. If your vehicle is equipped with a touchscreen, this feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “unders...

  • Page 136

    Of operation. Then, the heat output will drop to the normal hi-level. If the hi-level setting is selected, the system will automatically switch to lo-level after ap- proximately 60 minutes of continuous operation. At that time, the number of illuminated leds changes from two to one, indicating the c...

  • Page 137

    Manual seat adjuster — if equipped both front seats are adjustable forward or rearward. The manual seat adjustment handle is located under the seat cushion at the front edge of each seat. While sitting in the seat, pull up on the handle and slide the seat forward or backward. Release the bar once yo...

  • Page 138

    Handle, lean back on the seatback and when you reach the desired position, release the handle. Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury o...

  • Page 139

    Impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be prop- erly installed and adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted...

  • Page 140

    Warning! • a loose head restraint thrown forward in a colli- sion or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow removed head restraints in a location outside the occupant compartment. • all the head restraints must be reinstalled in the vehicle to...

  • Page 141

    Push the adjustment button located on the base of the head restraint and push downward on the head restraint. To remove the head restraint, push the adjustment button and the release button while pulling upward on the whole assembly. To reinstall the head restraint, put the head restraint posts into...

  • Page 142

    Note: • the rear center head restraint (crew cab and quad cab) has only one adjustment position that is used to aid in the routing of a tether. Refer to “occupant restraints” in “things to know before starting your vehicle” for further information. • do not reposition the head restraint 180 degrees ...

  • Page 143

    The memory seat buttons are located on the outboard side of the drivers seat cushion. Programming the memory feature note: to create a new memory profile, perform the following: 1. Cycle the vehicles ignition to the on/run position (do not start the engine). 2. Adjust all memory profile settings to ...

  • Page 144

    Note: • memory profiles can be set without the vehicle in park, but the vehicle must be in park to recall a memory profile. • to set a memory profile to your rke transmitter, refer to “linking and unlinking the remote keyless entry transmitter to memory” in this section. Linking and unlinking the re...

  • Page 145

    3. Once the profile has been recalled, push and release the set (s) button on the memory switch, then push and release button (1) or (2) accordingly. “memory profile set” (1 or 2) will display in the instrument cluster on vehicles equipped with the evic/did. 4. Push and release the lock button on th...

  • Page 146

    • to recall the memory settings for driver one using the rke transmitter, push the unlock button on the rke transmitter linked to memory position 1. Driver two memory position recall • to recall the memory setting for driver two using the memory switch, push memory button number 2 on the memory swit...

  • Page 147

    • when you remove the key fob from the ignition (or change the ignition to off, for vehicles equipped with keyless enter-n-go™), the driver seat will move to a position 0.3 in (7.7 mm) forward of the rear stop if the driver seat position is between 0.9 in and 2.7 in (22.7 mm and 67.7 mm) forward of ...

  • Page 148

    2. Reach into the opening beneath the center of the hood and push the safety latch lever to the left to release it, before raising the hood. Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches eng...

  • Page 149

    Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. Lights the headlight switch is located on the left side...

  • Page 150

    To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Note: if your vehicle is equipped with illuminated approach lights under the outside mirrors they can be turned of...

  • Page 151

    When the system is on, the headlight delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch to the off position. To turn the automatic headlights off, turn the headlight switch out of the auto position. Note: the engine must be runnin...

  • Page 152

    Center (evic)” or “driver information display (did)” in “understanding your instrument panel” for further in- formation. Daytime running lights (drl) — if equipped the headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except park. This provides...

  • Page 153

    Automatic high beam headlamp control — if equipped the automatic high beam headlamp control system provides increased forward lighting at night by automat- ing high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle specific light and ...

  • Page 154

    If the windshield or automatic high beam headlamp control mirror is replaced, the mirror must be re-aimed to ensure proper performance. See your local authorized dealer. To activate 1. If your vehicle is equipped with a touchscreen, the automatic high beams are enabled through the uconnect® system. ...

  • Page 155

    Parking lights and panel lights to turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the o (off) position. Fog lights — if equipped the fog lights are turned on by rotating the headlight ...

  • Page 156

    Turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the high beam is selected. Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is o...

  • Page 157

    The brightness of the instrument panel as well as the ambient lighting can be regulated by rotating the dimmer control right (brighter) or left (dimmer). When the head- lights are on you can supplement the brightness of the odometer, trip odometer, radio and overhead console by rotating the control ...

  • Page 158

    (rke) transmitter, if equipped. These lights are also operated individually as reading lights by pushing on the corresponding lens. Note: the courtesy/reading lights will remain on until the switch is pushed a second time, so be sure they have been turned off before leaving the vehicle. If the inter...

  • Page 159

    Ambient light the overhead console is equipped with an ambient light feature. This light casts illumination for improved visibil- ity of the floor console area. Cargo light the cargo lights are turned on by pushing on the cargo button. The cargo lights will also turn on for approximately 30 seconds ...

  • Page 160

    Multifunction lever the multifunction lever is located on the left side of the steering column. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light re...

  • Page 161

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Flash-to-pass you can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer-...

  • Page 162

    Windshield wipers and washers windshield wipers the wipers and washers are operated by a switch in the multifunction lever. Turn the end of the handle to select the desired wiper speed. Windshield wiper operation rotate the end of the lever upward, to the first detent past the intermittent settings ...

  • Page 163

    Windshield washers to use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to the second detent. Washer fluid will be sprayed and the wiper will operate for two to three cycles after the washer knob is released from this position. If the washer knob ...

  • Page 164

    Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Rain sensing wipers — if equipped this feature senses moisture on the windshield and automaticall...

  • Page 165

    • the rain sensing feature may not function properly when ice, or dried salt water is present on the wind- shield. • use of rain-x® or products containing wax or silicone may reduce rain sensing performance. The rain sensing system has protection features for the wiper blades and arms, and will not ...

  • Page 166

    Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Release the lever to lock the steering column firmly in place. Warning! Do not adjust the steering column while driving. Adjusting the ...

  • Page 167

    • the pedals can be adjusted with the ignition off. • the pedals cannot be adjusted when the vehicle is in reverse or when the electronic speed control sys- tem is on. The following messages will be displayed on vehicles equipped with the electronic vehicle informa- tion system (evic) or driver info...

  • Page 168

    Caution! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path. Warning! Do not adjust the pedals while the vehicle is ...

  • Page 169

    During a remote start through the uconnect® system. Refer to “uconnect® settings” in “understanding your instrument panel” for further information. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol u...

  • Page 170

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 171

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 172

    The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “under- standing your instrument panel” for more information. The speed increment shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pushing the res (+)...

  • Page 173

    • if the button is continually pushed, the set speed will continue to decrease until the button is released, then the new set speed will be established. Metric speed (km/h) • pushing the set (-) button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a...

  • Page 174

    Overhead console — if equipped the overhead console is located on the headliner above the rearview mirror. The overhead console contains the following features: • courtesy/reading lights • power sliding rear window switch — if equipped courtesy/reading lights both lights in the overhead console and ...

  • Page 175

    (rke) transmitter, if equipped. These lights are also operated individually as reading lights by pushing on the corresponding lens. Note: the courtesy/reading lights will remain on until the switch is pushed a second time, so be sure they have been turned off before leaving the vehicle. If the inter...

  • Page 176

    Electrical power outlets the auxiliary 12 volt (13 amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 volt power outlets have a cap attached to the outlet indicating “12v dc,” together with either a key symbol or a battery symb...

  • Page 177

    • lower left and lower right of the center stack when equipped with a bench seat. • center console when equipped with bucket seats. Power outlets — center stack 1 — power outlet 2 — usb port (charge only) power outlet — center console 3 understanding the features of your vehicle 175.

  • Page 178

    • inside the upper lid of the center storage compartment — if equipped. • rear of the center console storage compartment — quad cab® or crew cab. Power outlet — upper lid power outlet — rear center console 176 understanding the features of your vehicle.

  • Page 179

    Power outlet — rear center console fuse power outlet fuse locations 1 — f104 fuse 20 a yellow power outlet console bin 2 — f90–f91 fuse 20 a yellow power outlet rear center console 3 — f93 fuse 20 a yellow cigar lighter instrument panel 3 understanding the features of your vehicle 177.

  • Page 180

    The key symbol indicates that this outlet can supply power when the key is in the on/run or acc posi- tions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge. Warning! To avoid serious injury or death: ...

  • Page 181

    Auxiliary switches — if equipped there can be up to five auxiliary switches located in the lower switch bank of the instrument panel which can be used to power various electronic devices and pto (power take off) – if equipped. Connections to the switches are found under the hood in the connectors at...

  • Page 182

    For vehicles equipped with a floor console, the cuphold- ers may be used. Power inverter — if equipped a 115 volt (150 watts maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devic...

  • Page 183

    To turn on the power outlet, simply plug in the device. The outlet automatically turns off when the device is unplugged. Note: due to built-in overload protection, the power inverter will shut down if the power rating is exceeded. Warning! To avoid serious injury or death: • do not insert any object...

  • Page 184

    Front instrument panel cupholders — floor storage bin for vehicles equipped with bucket seats two cupholders are located in the floor storage bin. Rear cupholders — if equipped some vehicles are equipped with rear cupholders located in the center armrest. Front cupholders for bucket seats rear armre...

  • Page 185

    Some vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passenger conve- nience. Storage glove compartment the glove compartment is located on the passenger side of the instrument panel and features both an upper and lower storage area. Rear cup wells 3 understand...

  • Page 186

    To open the upper glove compartment push upward on the handle release. The glove compartment door will automatically open. Glove compartment 1 — upper glove compartment 2 — lower glove compartment upper glove compartment 184 understanding the features of your vehicle.

  • Page 187

    To open the lower glove compartment, pull on the handle to release the latch and lower the glove compartment door. Door storage front door storage — if equipped storage areas and bottle holders (drivers side only) are located in the door trim panels. Lower glove compartment front door storage 3 unde...

  • Page 188

    Rear door storage — if equipped storage compartments are located in both the driver and passenger rear door trim panels. Center storage compartment — if equipped the center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains...

  • Page 189

    Warning! • this armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or a collision. Only use the center seat- ing position when the armrest is fully upright. • in a collision, the latch may open if the total weight of the items stored exceeds abou...

  • Page 190

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Seatback storage located in the back of both the driver and passenger front seats are pockets that can be used for storage. L...

  • Page 191

    Storage (regular cab) the storage bin is located behind the front seats and runs the length of the cab. Storage and seats (crew cab) the crew cab models provide additional storage under the rear seats. Lift the seats to access the storage com- partment. To open the storage compartments, lift upward ...

  • Page 192

    Caution! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids. Plastic grocery bag retainers (regular cab models) retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab...

  • Page 193

    On the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ap- proximately 10 minutes. For an additional five minutes of operation, push the button...

  • Page 194

    Push the switch to the right to open the glass. Pull the switch to the left to close the glass. Manual sliding rear window — if equipped a locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. Rear window switch 192 un...

  • Page 195: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .196 䡵 instrument cluster — base. . . . . . . . . . .197 䡵 instrument cluster — premium . . . . . . .198 䡵 instrument cluster descriptions . . . . .199 䡵 electronic vehicle information center (evic) . . . . . ...

  • Page 196

    ▫ did white telltales . . . . . . . . . . . . . . . . . . . .248 ▫ did selectable menu items . . . . . . . . . . . . . .248 䡵 uconnect® settings . . . . . . . . . . . . . . . . . . .260 ▫ buttons on the faceplate. . . . . . . . . . . . . . . .262 ▫ buttons on the touchscreen. . . . . . . . . . . . ....

  • Page 197

    ▫ basic voice commands. . . . . . . . . . . . . . . . . .309 ▫ radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .311 ▫ media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .312 ▫ climate (8.4a/8.4an) . . . . . . . . . . . . . . . . . .313 ▫ navigation (8.4a/8.4an) . . . . . ...

  • Page 198

    Instrument panel features 1 — headlight switch 7 — 115v power inverter outlet 13 — gear selector/transfer case position switch — if equipped 2 — instrument cluster 8 — power outlet — if equipped 14 — ignition switch 3 — radio 9 — lower switch bank 15 — hood release 4 — hazard switch 10 — instrument ...

  • Page 199

    Instrument cluster — base 4 understanding your instrument panel 197.

  • Page 200

    Instrument cluster — premium 198 understanding your instrument panel.

  • Page 201

    Instrument cluster descriptions 1. Tachometer the tachometer indicates engine speed in revolutions per minute (rpm x 1000). Caution! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine operation over 3200 rpm can result in significant damage that will not b...

  • Page 202

    Testing the light will come on when the ignition is first turned on and remain on for 15 seconds, then blink for 5 seconds, and remain on until the vehicle is started. If the bulb does not come on during starting, have the condi- tion investigated promptly. If this light comes on and remains on whil...

  • Page 203

    Note: • a continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. • check for an inoperative outside light bulb if either indicator remains on and does not flash, or flashes at a rapid rate. 5. Voltmeter — if equipped when the engine is running, the...

  • Page 204

    Hydraulic system malfunction or that a problem with the brake booster has been detected by the anti-lock brake system (abs) / electronic stability control (esc) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ...

  • Page 205

    Unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the ...

  • Page 206

    Dealer as soon as possible. Refer to “occupant restraints” in “things to know before starting your vehicle” for further information. 10. Oil pressure gauge — if equipped the pointer should always indicate some oil pres- sure when the engine is running. A continuous high or low reading under normal d...

  • Page 207

    16. Tire pressure monitoring telltale light — if equipped each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (if your vehicle has tir...

  • Page 208

    Of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the tpms from functioning properly. Always check the tpms malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires...

  • Page 209

    18. Electronic vehicle information center (evic)/driver information display (did) the evic/did features a driver-interactive display that is located in the instrument cluster. For further informa- tion, refer to “electronic vehicle information center (evic” or “/driver information display (did)” in ...

  • Page 210

    23. Electronic stability control (esc) activation/ malfunction indicator light — if equipped the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is turned to the on/run position. It should go out with the engine running. If the “esc activa...

  • Page 211

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 212

    Vehicle has completely stopped and the shift lever is placed in the park position. The light should turn off. If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when th...

  • Page 213

    Rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. For further information on four-wheel drive operation and proper use, refer to “four-wheel drive operation — if equipped” in “starting and operating.” electronic vehicle information cente...

  • Page 214

    • trip a • trip b • stop/start info (if equipped) • air suspension (if equipped) • trailer tow • messages • screen setup • vehicle settings (not equipped with a uconnect® 5.0 & 8.4 radio) the system allows the driver to select information by pushing the following evic control buttons located on the ...

  • Page 215

    • down arrow button push and release the down arrow button to scroll downward through the main menu items. • right arrow button push and release the right arrow button to access/select the information screens or sub- menu screens of a main menu item. Push and hold the right arrow button for two seco...

  • Page 216

    The evic displays are located in the center portion of the cluster and consists of seven sections: 1. Compass display displays the current direction. Refer to “compass set- tings” under “customer programmable features — uconnect® 5.0/8.4 settings” for further information. 2. Temperature display disp...

  • Page 217

    The evic’s compass/outside temp line. Examples of this message type are “right front turn signal lamp out” and “low tire pressure.” • unstored messages this message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are “turn si...

  • Page 218

    Vehicles equipped with passive entry 1. Without pushing the brake pedal, push the engine start/stop button and cycle the ignition to the on/run position (do not start the engine). 2. Push and release the down arrow button to scroll downward through the main menu to “vehicle info.” 3. Push and releas...

  • Page 219

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Evic messages • front seatbelts unbuckled • driver seatbelt unbuckled • passenger seatbelt unbuckled • service airbag system • traction control o...

  • Page 220

    • battery voltage low • service electronic throttle control • lights on • right turn signal light out • left turn signal light out • turn signal on • sound horn with remote lock: off; 1st press; 2nd press • vehicle not in park • key in ignition • key in ignition lights on • remote start active key t...

  • Page 221

    • doors open • gear not available • shift not allowed • shift to neutral then drive or reverse • automatic unavailable use autostick service req. • transmission getting hot press brake • trans. Hot stop safely shift to park wait to cool • transmission cool ready to drive • trailer brake disconnected...

  • Page 222

    • oil pressure warning light this telltale indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not s...

  • Page 223

    Vehicle has completely stopped and the shift lever is placed in the park position. The light should turn off. If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when th...

  • Page 224

    • trailer brake disconnected warning light this telltale is on when the trailer brake has been disconnected. Evic yellow telltales this area will show reconfigurable yellow caution tell- tales. These telltales include: • low fuel telltale when the fuel level reaches approximately 3.0 gal (11.0 l), t...

  • Page 225

    Caution! Continuous driving with the transmission tempera- ture warning light illuminated will eventually cause severe transmission damage or transmission failure. Warning! If you continue operating the vehicle when the transmission temperature warning light is illumi- nated you could cause the flui...

  • Page 226

    Evic selectable menu items push and release the up or down arrow buttons until the desired selectable menu item is highlighted in the evic. Speedometer menu item push and release the up or down arrow button until the speedometer menu item is highlighted in the evic. Push and release the right arrow ...

  • Page 227

    • average fuel economy value • range to empty • dual fuel tank levels — if equipped • push and release the right arrow button to display the fuel tank level submenu item. Your evic will display the fuel levels of the front and rear fuel tanks. The fuel is automatically transferred from the rear tank...

  • Page 228

    Release the right arrow button and the next screen will display the following trailer trip information: • trip (trailer specific) distance: push and hold the right arrow button to reset the distance. • trailer brake • output • type • gain evic messages • front seatbelts unbuckled • driver seatbelt u...

  • Page 229

    • service tire pressure system • parking brake engaged • brake fluid low • service electronic braking system • engine temperature hot • battery voltage low • service electronic throttle control • lights on • right turn signal light out • left turn signal light out • turn signal on • sound horn with ...

  • Page 230

    • service airbag warning light • driver seatbelt unbuckled • passenger seatbelt unbuckled • front seatbelts unbuckled • door open • doors open • gear not available • shift not allowed • shift to neutral then drive or reverse • automatic unavailable use autostick service req. • transmission getting h...

  • Page 231

    You to change what information is displayed in the instrument cluster as well as the location that information is displayed. Vehicle settings menu item personal settings allows the driver to set and recall features when the transmission is in park. Push and release the up and down button until set- ...

  • Page 232

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 3 parksense parksense • notification — sound only; sound & display • front volume — low; medium; high • rear volume — low; medium; high 4 tilt mirror in re- verse tilt mirror in r on; off 5 rain sensing ...

  • Page 233

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 11 daytime running lights daytime lights on; off 12 flash lights with lock lights w/ lock on; off 13 auto lock doors auto lock doors on; off 14 auto unlock doors auto unlock doors on; off 15 sound horn w...

  • Page 234

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 19 passive entry passive entry on; off 20 remote start com- fort system rmt start comfort off; remoter start; all starts 21 easy exit seat easy exit seat on; off 22 key-off power delay power off delay of...

  • Page 235

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 30 horn w/ remote lower horn w/ rmt lwr on; off 31 lights w/ remote lower lights w/ rmt lwr on; off 32 trailer select trailer select trailer 1; trailer 2; trailer 3; trailer 4 33 brake type brake type li...

  • Page 236

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 34 trailer name trailer name • trailer # (# is equal to slot position) • boat • car • cargo • dump • equipment • flatbed • gooseneck • horse • livestock • motorcycle • snowmobile • travel • utility • 5th...

  • Page 237

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 35 compass variance compass var 1-15 increments of 1 36 calibrate compass compass cal cancel; calibrate 37 fuel saver display fuel saver on; off turn menu off push and release the right arrow button to e...

  • Page 238

    The did menu items consists of the following: • digital speedometer • vehicle info • fuel economy info • trip a • trip b • stop/start info (if equipped) • trailer tow • audio • stored messages • screen setup • vehicle settings (not equipped with a uconnect® 5.0 & 8.4 radio) driver information displa...

  • Page 239

    The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: • up arrow button push and release the up arrow button to scroll upward through the main menu and submenus. • down arrow button push and release the down arrow button to scroll downward...

  • Page 240

    • right arrow button push and release the right arrow button to access/select the information screens or sub- menu screens of a main menu item. Push and hold the right arrow button for two seconds to reset displayed/selected features that can be reset. • left arrow button push and release the left a...

  • Page 241

    1. Main screen — the inner ring of the display will illuminate in grey under normal conditions, yellow for non critical warnings, red for critical warnings, and white for on demand information. 2. Audio / phone information and sub-menu informa- tion — whenever there are sub-menus available, the posi...

  • Page 242

    The did’s compass/outside temp line. Examples of this message type are “right front turn signal lamp out” and “low tire pressure.” • unstored messages this message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are “turn sig...

  • Page 243

    Vehicles equipped with passive entry 1. Without pushing the brake pedal, push the engine start/stop button and cycle the ignition to the on/run position (do not start the engine). 2. Push and release the down arrow button to scroll downward through the main menu to “vehicle info.” 3. Push and releas...

  • Page 244

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Did messages • front seatbelts unbuckled • driver seatbelt unbuckled • passenger seatbelt unbuckled • service airbag system • traction control of...

  • Page 245

    • battery voltage low • service electronic throttle control • lights on • right turn signal light out • left turn signal light out • turn signal on • sound horn with remote lock: off; 1st press; 2nd press • vehicle not in park • key in ignition • key in ignition lights on • remote start active key t...

  • Page 246

    • doors open • gear not available • shift not allowed • shift to neutral then drive or reverse • automatic unavailable use autostick service req. • transmission getting hot press brake • trans. Hot stop safely shift to park wait to cool • transmission cool ready to drive • trailer brake disconnected...

  • Page 247

    • oil pressure warning light this telltale indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not s...

  • Page 248

    Vehicle has completely stopped and the shift lever is placed in the park position. The light should turn off. If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when th...

  • Page 249

    Did yellow telltales this area will show reconfigurable yellow caution tell- tales. These telltales include: • low fuel telltale when the fuel level reaches approximately 3.0 gal (11.0 l), this light will turn on, and remain on until fuel is added. • windshield washer fluid low indicator this tellta...

  • Page 250

    Warning! If you continue operating the vehicle when the transmission temperature warning light is illumi- nated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. • loose fuel filler cap this telltale will turn on to indicate that the fuel...

  • Page 251

    Digital speedometer push and release the up or down arrow button until the digital display icon is high- lighted in the did. Push and release the right arrow button to change the display be- tween mph and km/h. Vehicle info push and release the up or down arrow button until the vehicle info icon is ...

  • Page 252

    • transmission temperature (automatic only) • oil temperature • oil pressure • engine hours fuel economy push and release the up or down arrow button until the fuel economy menu icon/title is highlighted. Submenu item: • range • current mpg or l/100 km • average mpg or l/100 km • to reset the follow...

  • Page 253

    • distance mi or km • average mpg or l/100 km • average mph or km/h • elapsed time hold the right arrow button to reset all the informa- tion. Trip b push and release the up or down arrow button until the trip b icon/title is highlighted in the did. The trip b information will display the following:...

  • Page 254

    Audio push and release the up or down arrow button until the audio display icon is high- lighted in the did. Push and release the right arrow button to display the active source. Stored messages push and release the up arrow button until the messages display icon is highlighted in the did. This feat...

  • Page 255

    Settings options 1 upper left • none • compass • outside temp. • time • range • average mpg • current mpg • trip a • trip b • trailer trip • trailer brake gain 2 upper right • none • compass • outside temp. • time • range • average mpg settings options • current mpg • trip a • trip b • trailer trip ...

  • Page 256

    Settings options 4 lower right • none • compass • outside temp. • time • range • average mpg • current mpg • trip a • trip b • trailer trip • trailer brake gain 5 upper gauge • none • compass • outside temp. • time • range • average mpg settings options • current mpg • trip a • trip b • trailer trip...

  • Page 257

    Settings options 7 odometer • 000 • 000.0 8 restore defaults • cancel • ok vehicles settings (customer-programmable features) note: this feature is only available on 5.0 and 8.4 uconnect® radios personal settings allows the driver to set and recall features when the transmission is in park. Push and...

  • Page 258

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 3 parksense parksense • notification — sound only; sound & display • front volume — low; me- dium; high • rear volume — low; me- dium; high 4 tilt mirror in reverse tilt mirror in r on; off 5 rain sensing wi...

  • Page 259

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 11 flash lights with lock lights w/ lock on; off 12 auto lock doors auto lock doors on; off 13 auto unlock doors auto unlock doors on; off 14 sound horn with remote start horn w/ rmt start on; off 15 sound h...

  • Page 260

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 22 commercial settings commercial • aux switches • power take-off • pin setup 23 air suspension display alerts air susp. Alerts all; warnings only 24 aero ride height mode aero mode on; off 25 tire/jack mode...

  • Page 261

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 32 trailer name trailer name • trailer # (# is equal to slot position) • boat • car • cargo • dump • equipment • flatbed • gooseneck • horse • tag • motorcycle • snowmobile • travel • utility • 5th wheel 4 u...

  • Page 262

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 33 compass variance compass var 1-15 increments of 1 34 calibrate compass compass cal cancel; calibrate 35 fuel saver display fuel saver on; off 36 park assist front chime vol- ume park assist front chime vo...

  • Page 263

    Uconnect® 5.0 buttons on the touchscreen and buttons on the faceplate 1 — uconnect® buttons on the touchscreen 2 — uconnect® buttons on the faceplate uconnect® 8.4a/8.4an buttons on the touchscreen and buttons on the faceplate 1 — uconnect® buttons on the touchscreen 2 — uconnect® buttons on the fac...

  • Page 264

    Buttons on the faceplate buttons on the faceplate are located below the uconnect® system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side of the climate controls in the center of the instru- ment panel. Turn the control knob to scroll...

  • Page 265

    When making a selection, press the button on the touch- screen to enter the desired mode. Once in the desired mode, press and release the preferred setting until a check-mark appears next to the setting, showing that setting has been selected. Once the setting is complete, either press the “back arr...

  • Page 266

    Note: to make changes to the ⬙display brightness with headlights on ⬙ setting, the headlights must be on and the interior dimmer switch must not be in the ⬙party⬙ or ⬙parade⬙ positions. • display brightness with headlights off when in this display, you may select the brightness with the headlights o...

  • Page 267

    • units when in this display, you may select to have the driver information display (did), odometer, and navigation system (if equipped) changed between us and metric units of measure. Press “us” or “metric” until a check- mark appears next to the setting, showing that setting has been selected. Pre...

  • Page 268

    • fuel saver display — if equipped this feature will allow you to enable fuel saver mode and will be displayed in the did. Press the “fuel saver display” button on the touchscreen, until a check-mark appears next to the setting, showing that setting has been selected. Press the back arrow button on ...

  • Page 269

    • time format this feature will allow you to select the time format display setting. Press the “time format” button on the touchscreen until a check-mark appears next to the 12hrs or 24hrs setting, showing that setting has been selected. Press the back arrow button on the touchscreen to return to th...

  • Page 270

    • parkview® backup camera your vehicle may be equipped with the parkview® rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the radio touchscreen display along with a cau...

  • Page 271

    Indicating that the setting had been selected. Press the back arrow button on the touchscreen to return to the previous menu. • rain sensing auto wipers when this feature is selected, the system will automati- cally activate the windshield wipers if it senses moisture on the windshield. To make your...

  • Page 272

    The headlights will also turn off when the wipers are turned off, if they were turned on by this feature. To make your selection, press the “headlights with wipers” button on the touchscreen, until a check-mark appears next to the setting, showing that setting has been se- lected. Press the back arr...

  • Page 273

    Make your selection, press the “auto unlock on exit” button on the touchscreen, until a check-mark appears next to the setting, showing that the setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu. • sound horn with lock when this feature is selec...

  • Page 274

    Note: if the vehicle is programmed 1st push of key fob unlocks, all doors will unlock no matter which passive entry equipped door handle is grasped. If 1st push of key fob unlocks is programmed, only the driver’s door will unlock when the driver’s door is grasped. With passive entry, if 1st push of ...

  • Page 275

    Note: the seat will return to the memorized seat location (if personal settings linked to key fob is set to on) when the remote keyless entry (rke) transmitter is used to unlock the door. Refer to “driver memory seat” in “understanding the features of your vehicle” for further information. Auto comf...

  • Page 276

    Engine off options after pressing the “engine off options” button on the touchscreen the following settings will be available: • easy exit seats — if equipped when this feature is selected, the driver’s seat will automatically move rearward once the engine is shut off. To make your selection, press ...

  • Page 277

    Compass settings — uconnect® 5.0 after pressing the “compass settings” button on the touchscreen the following settings will be available: • variance compass variance is the difference between magnetic north and geographic north. To compensate for the differences the variance should be set for the z...

  • Page 278

    Driver information display (did) will display cal until the compass is calibrated. You may also calibrate the compass by pressing the “on” button on the touchscreen and completing one or more 360-degree turns (in an area free from large metal or metallic objects) until the cal indicator displayed in...

  • Page 279

    Button on the touchscreen, select “on” or “off.” press the back arrow button on the touchscreen to return to the previous menu. • aux volume offset — if equipped this feature provides the ability to tune the audio level for portable devices connected through the aux input. To make your selection, pr...

  • Page 280

    Trailer brake after pressing the “trailer brake” button on the touch- screen the following settings will be available: • trailer select when this feature is selected, the trailer type can be selected between “trailer 1,” “trailer 2,” “trailer 3” and “trailer 4.” to make your selection, scroll up or ...

  • Page 281

    • subscription information new vehicle purchasers or lessees will receive a free limited time subscription to siriusxm satellite radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the subscription information screen to re-subscribe...

  • Page 282

    For further information, refer to the uconnect® supple- ment manual or visit uconnectphone.Com. Steering wheel audio controls — if equipped the remote sound system controls are located on the back surface of the steering wheel. Reach behind the wheel to access the switches. Center console usb/aux sd...

  • Page 283

    The right hand control is a rocker type switch with a push-button in the center. Pushing the top of the switch will increase the volume, and pushing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to radio, cd or other v...

  • Page 284

    2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not...

  • Page 285

    Nevertheless, the wireless radio will be used in such a manner that the radio is 20 cm or further from the human body. The internal wireless radio operates within guidelines found in radio frequency safety standards and recom- mendations, which reflect the consensus of the scientific community. The ...

  • Page 286

    Note: • this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful inter- ference in a residential installation. This equipment generates, uses and c...

  • Page 287

    Front blower control there are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position. Temperature control use this control to regulate the tem- perature o...

  • Page 288

    Air conditioning operation push the a/c button to engage the air conditioning (a/c). A led will illu- minate when the a/c system is engaged. Max a/c for maximum cooling, when max a/c is selected the a/c is turned on automatically and the air is recirculated. Note: a/c cannot be deselected when in ma...

  • Page 289

    Closer the control is to a particular mode, the more air distribution you receive from that mode. Panel mode air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Bi-level mode air is directed through the panel and floor outlets. Note: there ...

  • Page 290

    With maximum blower and warm temperature settings for best windshield and side window defrosting. Note: the air conditioning compressor operates in mix and defrost, or a blend of these modes even if the a/c button is not pushed. This dehumidifies the air to help dry the windshield. To improve fuel e...

  • Page 291

    Air outlets the airflow from each of the instrument panel outlets can be adjusted for direction, and turned on or off to control airflow. Note: for maximum airflow to the rear, the center instrument panel outlets can be directed toward the rear seat passengers. Economy mode if economy mode is desire...

  • Page 292

    Manual climate controls with touchscreen — if equipped buttons on the faceplate the buttons on the faceplate are located below the radio touchscreen. Buttons on the touchscreen buttons on the touchscreen are accessible on the radio. Climate controls — buttons on the faceplate temperature controls — ...

  • Page 293

    Button descriptions (applies to both buttons on the faceplate and buttons on the touchscreen) 1. Max a/c button press and release to toggle between max a/c and the prior settings. The button on the touchscreen illuminates when max a/c is on. In max a/c, the blower level and mode position can be adju...

  • Page 294

    Equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 10 minutes. Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abra...

  • Page 295

    Note: bi-level mode is designed under comfort con- ditions to provide cooler air out of the panel outlets and warmer air from the floor outlets. • floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. • mix mode air come...

  • Page 296

    8. Climate control off button press and release this button to turn the climate control on/off. 9. Temperature control down button push the button on the faceplate for cooler temperature settings. On the touchscreen, slide the temperature bar towards the blue arrow button for cooler temperature sett...

  • Page 297

    Automatic climate controls with touchscreen — if equipped buttons on the faceplate the buttons on the faceplate are located below the uconnect® screen. Buttons on the touchscreen buttons on the touchscreen are accessible on the uconnect® system screen. Automatic climate controls — buttons on the fac...

  • Page 298

    Button descriptions (applies to both buttons on the faceplate and buttons on the touchscreen) 1. Max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manual mode an...

  • Page 299

    5. Front defrost button press and release to change the current airflow setting to defrost mode. The indicator illuminates when this fea- ture is on. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level will increase. Use defrost mode wi...

  • Page 300

    Temperature settings or on the touchscreen, press and slide the temperature bar towards the red arrow for warmer temperature settings. Note: pressing this button while in sync mode will automatically exit sync. 8. Passenger temperature control down button (uconnect® 8.4) provides the passenger with ...

  • Page 301

    Button on the touchscreen use the small blower icon to reduce the blower setting and the large blower icon to increase the blower setting. Blower can also be selected by pressing the blower bar area between the icons. 11. Modes the airflow distribution mode can be adjusted so air comes from the inst...

  • Page 302

    • mix mode air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. 12. Climate control off button press and release this button to turn the climate control on/off. 13. Driver temperature control down button (uconnect® 8.4) provides the driv...

  • Page 303

    Climate control functions a/c (air conditioning) the air conditioning (a/c) button allows the operator to manually activate or deactivate the air conditioning system. When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin. For improved fuel ...

  • Page 304

    In max a/c, the blower level and mode position can be adjusted to desired user settings. Pressing other settings will cause the max a/c operation to switch to the prior settings and the max a/c indicator will turn off. Recirculation control when outside air contains smoke, odors, or high humidity, o...

  • Page 305

    2. Next, adjust the temperature you would like the system to maintain by adjusting the driver and pas- senger temperature buttons on the faceplate or but- tons on the touchscreen. Once the desired temperature is displayed, the system will achieve and automati- cally maintain that comfort level. 3. W...

  • Page 306

    The operator can also select the direction of the airflow by selecting one of the available mode settings. A/c operation and recirculation control can also be manually selected in manual operation. Note: each of these features operates independently from each other. If any feature is controlled manu...

  • Page 307

    Vacation/storage any time you store your vehicle or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in fresh air with the blower setting in high. This will ensure adequate system lubrication to minimize the possibility of ...

  • Page 308

    Control setting suggestions for various weather conditions operating tips chart 306 understanding your instrument panel.

  • Page 309

    Uconnect® voice recognition introducing uconnect® start using uconnect® voice recognition with these helpful quick tips. It provides the key voice commands and tips you need to know to control your uconnect® 5.0 or 8.4a/8.4an system. Key features: • 5” touchscreen • three buttons on either side of t...

  • Page 310

    If you see the icon on your touchscreen, you have the uconnect® 8.4an system. If not, you have a uconnect® 8.4a system. Get started 1. Visit uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing in- structions. 2. Reduce background noise. Wind and passenger con...

  • Page 311

    Two buttons are all you need to control your uconnect® system with your voice. Basic voice commands the basic voice commands below can be given at any point while using your uconnect® system. Push the vr button . After the beep, say ѧ • cancel to stop a current voice session • help to hear a list of...

  • Page 312

    Uconnect® 5.0 uconnect® 8.4a/8.4an 310 understanding your instrument panel.

  • Page 313

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio® stations you would like to hear. (sub- scription or included siriusxm satellite radio® trial required.) push the vr button . After the beep, say ѧ • tune to ninety-five-point-five fm • tune to satellite channel hits 1 tip...

  • Page 314

    Media uconnect® offers connections via usb, sd, bluetooth® and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod® devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands a...

  • Page 315

    Tip: press the browse button on the touchscreen to see all of the music on your ipod® or usb device. Your voice command must match exactly how the artist, album, song and genre information is displayed. Climate (8.4a/8.4an) too hot? Too cold? Adjust vehicle temperatures hands- free and keep everyone...

  • Page 316

    Push the vr button . After the beep, say one of the following commands: • set driver temperature to 70 degrees • set passenger temperature to 70 degrees tip: voice command for climate may only be used to adjust the interior temperature of your vehicle. Voice command will not work to adjust the heate...

  • Page 317

    Navigation (8.4a/8.4an) the uconnect® navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. (navigation is optional on the uconnect® 8.4a system. See your dealer to activate navigation at any time.) 1. To enter a destination, push...

  • Page 318

    Push the phone button . After the beep, say one of the following commands ѧ • call john smith • dial 123-456-7890 and follow the system prompts • redial (call previous outgoing phone number) • call back (call previous incoming phone number) tip: when providing a voice command, push the phone button ...

  • Page 319

    Voice text reply uconnect® will announce incoming text messages. Push the phone button and say listen. (must have com- patible mobile phone paired to uconnect® system.) 1. Once an incoming text message is read to you, push the phone button . After the beep, say: “reply.” 2. Listen to the uconnect® p...

  • Page 320

    Tip: your mobile phone must have the full implementa- tion of the message access profile (map) to take advan- tage of this feature. For details about map, visit uconnectphone.Com. Apple iphone® ios6 or later sup- ports reading incoming text messages only. Uconnect® access (8.4a/8.4an) an included tr...

  • Page 321

    Register (8.4a/8.4an) 1. Press the apps button on the bottom of the 8.4-inch touchscreen. 2. If a pop-up message appears, press register or go to the favorite apps menu and press uconnect® regis- tration . 3. Read through the registration instructions. Enter and confirm your personal email address. ...

  • Page 322

    Download the uconnect® access app to a compatible apple® or android® mobile devices. All you need to do is: 1. After registering with uconnect® access, log on to your mopar® owner connect account at moparownerconnect.Com. 2. On the dashboard page, enter your mobile phone number to receive a link to ...

  • Page 323

    3. The uconnect® system will repeat your message and provide a variety of options to add to, delete, send or hear the message again. After the beep, tell uconnect® what you’d like to do. For instance, if you’re happy with your message, after the beep, say: “send.” you must be registered with uconnec...

  • Page 324

    Tip: once you perform a search, you can reorganize the results by selecting either the best match, rating or distance tab on the top of the touchscreen display. Siriusxm travel link™ (8.4a/8.4an) need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forec...

  • Page 325

    Tip: traffic alerts are not accessible with voice com- mand. Additional information © 2015 fca us llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of fca us llc. Android is a trademark of google inc. Siriusxm and all related marks and logo...

  • Page 327: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .330 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .330 ▫ automatic transmission . . . . . . . . . . . . . . . .331 ▫ extreme cold weather (below –20°f or −29°c) . .331 ▫ if engine fails to start . . ....

  • Page 328

    ▫ transfer case position indicator light . . . . . .354 ▫ electronically shifted transfer case (four-position switch) — if equipped . . . . . . . . . . . . . . . . .354 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . . .358 䡵 limited-slip differential . . . . . . . . . . . . .360 䡵 drivin...

  • Page 329

    ▫ tire identification number (tin). . . . . . . . . . .384 ▫ tire terminology and definitions . . . . . . . . . .386 ▫ tire loading and tire pressure . . . . . . . . . . .387 䡵 tires — general information . . . . . . . .392 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .392 ▫ tire in...

  • Page 330

    䡵 fuel requirements . . . . . . . . . . . . . . . . . .419 ▫ 5.7l/6.4l engines . . . . . . . . . . . . . . . . . . . . .419 ▫ reformulated gasoline . . . . . . . . . . . . . . . . .420 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . .420 ▫ e-85 usage in non-flex fuel vehicles . . . . . . .421 ...

  • Page 331

    ▫ general maintenance . . . . . . . . . . . . . . . . . . .448 䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . . . .449 ▫ towing this vehicle behind another vehicle . .449 ▫ recreational towing — two-wheel drive models . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 332

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 10- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Warnin...

  • Page 333

    Automatic transmission start the engine with the shift lever in the neutral or park. Apply the brake before shifting into any driving range. Note: this vehicle is equipped with a transmission shift interlocking system. The brake pedal must be pressed to shift out of park. Tip start feature do not pr...

  • Page 334

    Warning! (continued) • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. • if the...

  • Page 335

    Gasoline engine only the engine block heater cord is routed through the grille by the right front tow hook. It includes a removable cap that is secured by a tethered strap. It also has a c-clip that is used for storage when not in use for the winter months. During winter months, remove the heater co...

  • Page 336

    Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift ...

  • Page 337

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. The key fob can only be removed from the ignition when the ignition is in the lock...

  • Page 338

    Pull the shift lever toward you when shifting into re- verse or park, or when shifting out of park. The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt...

  • Page 339

    When parking on a level surface, you may shift the transmission into park first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting the transmission to park, otherwise the load on the transmission locking mechanism may make it diffi- cult to move the sh...

  • Page 340

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 341

    Caution! (continued) the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear range, as this can damage the drivetrain. The following indicators should be used to ensure that you have engaged the transmission in...

  • Page 342

    Warning! (continued) practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any other reason with the transmission in neutral can cause severe transmission damage. Re...

  • Page 343

    Torque converter clutch engagement. This is done to prevent transmission damage due to overheating. If the transmission becomes extremely hot or is in danger of overheating, the “transmission temperature warning light” may illuminate and the transmission may operate differently until the transmissio...

  • Page 344

    Transmission limp home mode transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, transmission limp home mode is activated. In this mode, the transmission remains in fourth gear (for 66rfe transmission) or thir...

  • Page 345

    Electronic range select (ers) operation the electronic range select (ers) shift control allows the driver to limit the highest available gear when the transmission is in drive. For example, if you shift the transmission into 4 (fourth gear), the transmission will not shift above fourth gear, but wil...

  • Page 346

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Note: to select the proper gear position for maximum deceleration (engine braking), simply push and hold the ers (...

  • Page 347

    When to use tow/haul mode when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, push the tow/haul switch to activate tow/ haul mode. This will improve performance and reduce the potential for transmission overheating or failure due t...

  • Page 348

    Desired, the switch must be pushed each time the engine is started. Warning! Do not use the “tow/haul” feature when driving in icy or slippery conditions. The increased engine braking can cause the rear wheels to slide, and the vehicle to swing around with the possible loss of vehicle control, which...

  • Page 349

    The transmission. This condition is normal and will not cause damage to the transmission. The torque con- verter will refill within five seconds after starting the engine. Power take off operation — if equipped (chassis cab only) this vehicle when equipped with pto prep and the as66rc automatic six-...

  • Page 350

    • vehicle engine must be running. • no vehicle, brake or clutch switch faults present. • pto must be correctly installed using the vehicle provided circuits. The electronic vehicle information center (evic) or driver information display (did) will display a ⬙pto on ⬙ message for five seconds if the ...

  • Page 351

    And remote) system is compatible with the vehicle’s electrical architecture and software functionality. Note: single set speed can be programmed via the pto menu on the evic/did screen. Further details are avail- able at the ram truck bodybuilders web site. Www.Rambodybuilder.Com www.Ramtrucks.Com. ...

  • Page 352

    Note: for application specific information with respect to pto and pump requirements and additional vehicle information (wiring schematics, preset idle values, en- gine speed limits, and vehicle hardware and software requirements) please refer to the body builders guide by accessing www.Rambodybuild...

  • Page 353

    The “transfer case position indicator light” in the instrument cluster will alert the driver that the vehicle is in four-wheel drive and that the front and rear drive- shafts are locked together. This light will illuminate when the transfer case is shifted into either the 4h or 4l position. There is...

  • Page 354

    Warning! (continued) neutral position without first fully engaging the parking brake. The transfer case neutral position disengages both the front and rear drive shafts from the powertrain and will allow the vehicle to roll, even if the transmission is in park. The parking brake should always be app...

  • Page 355

    Traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Caution! Do not use 4l (low) range when operating the vehicle on dry pavement. Driveline hardware dam- age can result. Shifting procedure — manually shifted transfer case 2h to 4h shifting betw...

  • Page 356

    Alignment and shift completion to occur. The preferred method is with the vehicle rolling 2 to 3 mph (3 to 5 km/h). Avoid attempting to engage or disengage 4l with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h). • do not attempt to shift into or from 4l while the transmission is in gear. Tr...

  • Page 357

    • neutral (neutral) this electronically shifted transfer case is designed to be driven in the two-wheel drive position (2wd) for normal street and highway conditions on dry, hard surfaced roads. When additional traction is required, the transfer case 4wd lock and 4wd low positions can be used to max...

  • Page 358

    3. When the shift is complete, the indicator light for the selected position will stop flashing and remain on. If one or more shift conditions are not met: 1. The indicator light for the current position will remain on. 2. The newly selected position indicator light will con- tinue to flash. 3. The ...

  • Page 359

    4wd lock positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the drivetrain. Beca...

  • Page 360

    4wd low four-wheel drive low range — this range provides low speed four-wheel drive. It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed. This range provides additional traction and maximum pulling power for loose, slippery road surfaces only. D...

  • Page 361

    When the shift is complete, the position indicator light for the selected position will stop flashing and remain on. 2wd to 4wd lock rotate the 4wd control switch to the desired position. Shifts between 2wd and 4wd lock can be done with the vehicle stopped or in motion. With the vehicle in motion, t...

  • Page 362

    2. Shift the transmission into neutral. 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is on (not flashing), shift the transmission back into gear. Alternate procedure 1. Bring the vehicle to a complete stop. 2. ...

  • Page 363

    Normal driving and cornering, the limited-slip unit per- forms similarly to a conventional differential. On slip- pery surfaces, however, the differential delivers more of the driving effort to the rear wheel having the better traction. The limited-slip differential is especially helpful during slip...

  • Page 364

    Warning! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have a collision. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet mud, loose sa...

  • Page 365

    Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow- ing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicl...

  • Page 366

    Caution! (continued) standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • do not exceed 5 mph (8 km/h) when d...

  • Page 367

    Note: • increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that there is a problem with the power steering system. • upon initial start-up in cold weather, the power steer- ing pump may make noise for a short amount of time. This is due to the co...

  • Page 368

    Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid. If necessary, add fluid to restore to the proper indicated leve...

  • Page 369

    When the parking brake is applied with the ignition switch on, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime ...

  • Page 370

    The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously ...

  • Page 371

    Brake system if power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. However, you will experience a substantial increase in braking effort to stop the vehicle. If either the front or rear hydraulic system loses normal bra...

  • Page 372

    Start assist (hsa), electronic stability control (esc), trailer sway control (tsc) and hill decent control (hdc [power wagon only]). All of the systems work together to enhance vehicle stability and control in vari- ous driving conditions, and are commonly referred to as esc. Anti-lock brake system ...

  • Page 373

    Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the anti-lock brake system (abs) cannot prevent the natural laws of physic...

  • Page 374

    Modulation transfers drive torque from slipping to non- slipping wheels to provide optimal forward traction. Hill start assist (hsa) the hsa system is designed to assist the driver in launching a vehicle on an incline. Hsa will maintain the level of brake pressure the driver inputs for a short durat...

  • Page 375

    Warning! (continued) always remember the driver is responsible for brak- ing the vehicle. The system will only work if the intended direction of the vehicle and vehicle gear match. For example, if the intended direction is forward up a hill and the vehicle is in drive and the activation criteria are...

  • Page 376

    Warning! (continued) vehicle or object behind you. In order to avoid rolling down the incline while resuming accelera- tion, manually activate the trailer brake or apply more vehicle brake pressure prior to releasing the brake pedal. Always remember the driver is re- sponsible for braking the vehicl...

  • Page 377

    The intended path, esc applies the brake of the appro- priate wheel to assist in counteracting the oversteer or understeer condition. • oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • understeer - when the vehicle is turning less than appropriate for ...

  • Page 378

    4wd lock or 4wd auto, the esc system will be in this mode. This mode should be used for almost all driving situations. Esc should only be turned to ⬙esc partial off ⬙ or “esc full off” for specific reasons as noted below. Esc partial off this mode is entered by momentarily pushing the “esc partial o...

  • Page 379

    Warning! (continued) the enhanced vehicle stability offered by the esc system is reduced. • trailer sway control (tsc) is disabled when the esc system is in the ⴖesc partial offⴖ mode. All four-wheel drive vehicles in 4wd auto and 4wd lock modes can also choose the following esc operating mode. This...

  • Page 380

    Will always be illuminated when esc is in ⬙esc partial off ⬙ and ⬙esc full off⬙. To turn esc on again, momen- tarily push the “esc off” switch. This will restore the normal “esc on” mode of operation. “esc full off” is the only operating mode for esc in 4wd low. Whenever the vehicle is started in 4w...

  • Page 381

    Speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. The “esc activation/malfunction indicator light” (lo- cated in the instrument cluster) starts to flash as soon as the tires lose traction and the esc system becomes act...

  • Page 382

    Appropriate wheel(s) to counteract the sway of the trailer. Tsc will become active automatically once an excessively swaying trailer is recognized. No driver action is re- quired to activate. Note that tsc cannot stop all trailers from swaying. Always use caution when towing a trailer and follow the...

  • Page 383

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 384

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 385

    Example: r = construction code – ⬙r⬙ means radial construction, or – ⬙d⬙ means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the r...

  • Page 386

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 387

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 388

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 389

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 5 starting and ...

  • Page 390

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 391

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this manual. To determine the maximum loading conditions of your v...

  • Page 392

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 393

    5 starting and operating 391.

  • Page 394

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 395

    Warning! (continued) • unequal tire pressures can cause steering prob- lems. You could lose control of your vehicle. • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended col...

  • Page 396

    Judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and ...

  • Page 397

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 398

    Radial ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision. Al- ways use radial ply tires in sets of four. Never combine them with other types of tires. Tire repair if your tire beco...

  • Page 399

    Summer or three season tires — if equipped summer tires provide traction in both wet and dry conditions, and are not intended to be driven in snow or on ice. If your vehicle is equipped with summer tires, be aware these tires are not designed for winter or cold driving conditions. Install winter tir...

  • Page 400

    Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). For speeds above 75 mph (120 km/h) refer to original equipment or an authorized tire dealer for recommended safe operating speeds, ...

  • Page 401

    Caution! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a compact or limited-use temporary spare installed. Damage to the vehicle may result. Spare tire matching original equipped tire and wheel — if equipped your vehicle may be equipped with a s...

  • Page 402

    Do not install more than one compact spare tire and wheel on the vehicle at any given time. Warning! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear...

  • Page 403

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your tire and loading inf...

  • Page 404

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. L...

  • Page 405

    Tread life. Rotation of these tires per the vehicle main- tenance schedule is highly recommended. Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have...

  • Page 406

    You may have on tire specifications or capability. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and...

  • Page 407

    Supplemental tire pressure information — if equipped a light load vehicle condition is defined as two passen- gers [150 lbs (68 kg) each] plus 200 lbs (91 kg) of cargo. Cold tire inflation pressures for a lightly loaded vehicle will be found on the face of the driver’s door. Tire chains (traction de...

  • Page 408

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 409

    Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation are...

  • Page 410

    Dual rear wheels the tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. Note: if your vehicle is equipped with a tire pressure in...

  • Page 411

    In incorrect locations for the pressure values displayed in the instrument cluster. Caution! 4500/5500 dual rear tires may only have one ap- proved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the on/off road tire. • when replacing a flat, the spare tire m...

  • Page 412

    Also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pres- sure. The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural ...

  • Page 413

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or ...

  • Page 414

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system — if equipped the tire pressure monitor system (tpms) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors moun...

  • Page 415

    The tpms consists of the following components: • receiver module • four tpm sensors • various tpms messages, which display in the elec- tronic vehicle information center (evic)/driver in- formation display (did) • tpm telltale light the matching full size spare wheel and tire assembly (if equipped) ...

  • Page 416

    Should this occur, you should stop as soon as possible and inflate the tires with a low pressure condition (those in a different color in the evic/did graphic) to the vehicle’s recommended cold placard pressure inflation value as shown in the ⬙inflate to xx⬙ message. Once the system receives the upd...

  • Page 417

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will no longer flash, and the ⬙service tpm system ⬙ message will no longer display, and a pressure value will disp...

  • Page 418

    Vehicles with matching full size spare • the matching full size spare wheel and tire assembly has a tpm sensor that can be monitored by the tpms. • if you install the full size spare in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition switch cycle...

  • Page 419

    System ⬙ message for a minimum of five seconds and then display dashes (- -) in place of the pressure value. • for each subsequent ignition switch cycle, a chime will sound, the tpm telltale light will flash on and off for 75 seconds and then remain on solid, and the evic/ did will display a ⬙servic...

  • Page 420

    The tpis consists of the following components: • receiver module • four tpm sensors (single rear wheel [srw] applica- tions) • six tpm sensors (dual rear wheel [drw] applica- tions) • pressure display in the electronic vehicle information center (evic)/driver information display (did) the tpis syste...

  • Page 421

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 422

    As hard starting, stalling, and hesitations. If you experi- ence these symptoms, try another brand of gasoline before considering service for the vehicle. Over 40 auto manufacturer’s world wide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) which def...

  • Page 423

    Problems that result from using gasoline containing methanol or gasoline containing more than 10% ethanol are not the responsibility of the manufacturer and may void or not be covered under new vehicle limited warranty. E-85 usage in non-flex fuel vehicles non-flex fuel vehicles (ffv) are compatible...

  • Page 424

    Detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel. Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is proh...

  • Page 425

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 426

    Caution! (continued) • to avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Note: when the fuel nozzle “clicks” or shuts off the fuel tank is full. Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being...

  • Page 427

    Will display in the evic/did telltale display area. Refer to “electronic vehicle information center (evic)/driver information display (did) in “understanding your in- strument panel” for further information. Tighten the fuel filler cap properly and push the select button to turn off the message. If ...

  • Page 428

    Each axle gawr is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension components sometimes specified by purchasers for in- creased durability does not necessarily increase the vehi- cle’s gvwr. Tire size the ...

  • Page 429

    Front or rear axles has been exceeded but the total load is within the specified gvwr. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally....

  • Page 430

    Exceed the gvwr. Refer to “vehicle loading/vehicle certification label” in “starting and operating” for further information. Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer ...

  • Page 431

    Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Tongue weight (tw) the tongue weight is the downward force exerted on the hitch ball by t...

  • Page 432

    Tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s directions, it pro- vides for a more level ride, offering more consistent steering and brake control, thereby enhancing towing safety. The addition of a friction/hydraulic sway control also dampens sway...

  • Page 433

    Without weight-distributing hitch (incorrect) with weight-distributing hitch (correct) 5 starting and operating 431.

  • Page 434

    Fifth-wheel hitch the fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. It connects a vehicle and fifth-wheel trailer with a coupling king pin. Gooseneck hitch the gooseneck hitch employs a pivoted coupling arm which atta...

  • Page 435

    Trailer hitch classification definitions class max. Trailer hitch in- dustry standards class i - light duty 2,000 lbs (907 kg) class ii - medium duty 3,500 lbs (1 587 kg) class iii - heavy duty 5,000 lbs (2 268 kg) class iv - extra heavy duty 10,000 lbs (4 540 kg) fifth wheel/gooseneck greater than ...

  • Page 436

    Cause of many trailer collisions. Never exceed the maxi- mum tongue weight stamped on your trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer • the weight of any other type of cargo or equipment put in or on your ...

  • Page 437

    Towing requirements to promote proper break-in of your new vehicle drive- train components the following guidelines are recom- mended: caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, durin...

  • Page 438

    Warning! (continued) the hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle transmission in ...

  • Page 439

    • check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “starting and operating” for the proper inspection procedure. • when replacing tires, refer to “tires – general infor- mation” in “starting and operating” for proper tire replacem...

  • Page 440

    • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • an electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. W...

  • Page 441

    The user interface consists of the following: manual brake control lever slide the manual brake control lever to the right to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes. If the manual brake control lever is activated while the brake is also applied, the g...

  • Page 442

    Sliding the manual brake control lever will display the gain setting for 10 seconds and the “trailer brake status indicator light” will not be displayed. If a fault is detected in the trailer wiring or the integrated trailer brake module (itbm), the “trailer brake status indicator light” will flash....

  • Page 443

    4. Push the up or down button on the steering wheel until “trailer tow” appears on the screen. 5. Push the right arrow on the steering wheel to enter “trailer tow”. 6. Push the up or down buttons until trailer brake type appears on the screen. 7. Push the right arrow and then push the up or down but...

  • Page 444

    Light electric heavy electric light eoh heavy eoh type of trailer brakes electric trailer brakes electric trailer brakes electric over hy- draulic trailer brakes electric over hy- draulic trailer brakes load *under 10,000 lbs *above 10,000 lbs *under 10,000 lbs *above 10,000 lbs * the suggested sele...

  • Page 445

    Warning! Connecting a trailer that is not compatible with the itbm system may result in reduced or complete loss of trailer braking. There may be a increase in stop- ping distance or trailer instability which could result in personal injury. Note: • an aftermarket controller may be available for use...

  • Page 446

    Automatic transmission — if equipped the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. However, if frequent shifting does occur while in drive, select tow/haul mode or select a lower gear range (using the electroni...

  • Page 447

    • when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. • use speed control in flat terrain and with light loads to maximize fuel efficiency. Cooling system to reduce potential for engine and transmission over- ...

  • Page 448

    Warning! (continued) do not expect that the airbag will perform as de- scribed earlier in this manual. Caution! The “lamp out” indicator could illuminate if exte- rior lamps are not properly installed. Before plowing • check the hydraulic system for leaks and proper fluid level. • check the mounting...

  • Page 449

    Ratings. These weights are specified on the safety com- pliance certification label on the driver’s side door opening. Note: detach the snowplow when transporting pas- sengers. Vehicle front end wheel alignment was set to specifica- tions at the factory without consideration for the weight of the pl...

  • Page 450

    General maintenance snowplows should be maintained in accordance with the plow manufacturer’s instructions. Keep all snowplow electrical connections and battery terminals clean and free of corrosion. When plowing snow, to avoid transmission and drive- train damage, the following precautions should b...

  • Page 451

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models flat tow none not al- lowed see instructions • automatic transmission in park • manual transmission in gear (not in neutral) •...

  • Page 452

    Recreational towing — two-wheel drive models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is allowed only if the rear wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly...

  • Page 453

    Recreational towing — four-wheel drive models note: both the manual shift and electronic shift trans- fer cases must be shifted into neutral (n) for recre- ational towing. Automatic transmissions must be shifted into park for recreational towing. Manual transmissions must be placed in gear (not in n...

  • Page 454

    Caution! (continued) • do not disconnect the rear driveshaft because fluid will leak from the transfer case, causing damage to internal parts. • do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Shifting into neutral (n) use the following procedure to...

  • Page 455

    3. Press and hold the brake pedal. 4. Depress the clutch pedal on a manual transmission. 5. With manual shift transfer case, shift the transfer case lever into neutral (n). With electronic shift transfer case, push and hold the transfer case neutral (n) button. Some models have a small, recessed ⬙n⬙...

  • Page 456

    Note: with electronic shift transfer case: • steps 2 through 5 are requirements that must be met before pushing the neutral (n) button, and must continue to be met until the shift has been completed. If any of these requirements are not met before push- ing the neutral (n) button or are no longer me...

  • Page 457

    • with electronic shift transfer case, press and hold the transfer case neutral (n) button until the neu- tral (n) indicator light turns off. After the neu- tral (n) indicator light turns off, release the neu- tral (n) button. After the neutral (n) button has been released, the transfer case will sh...

  • Page 459: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .458 䡵 if your engine overheats . . . . . . . . . . . .458 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .459 ▫ torque specifications . . . . . . . . . . . . . . . . . .460 䡵 jacking a...

  • Page 460

    Hazard warning flashers the hazard warning flasher switch is located on the upper switch bank just below the radio. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push...

  • Page 461

    Supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads hot (h), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer dr...

  • Page 462

    Torque specifications lug nut/bolt torque lug nut/ bolt type **lug nut/bolt size lug nut/ bolt socket size 120-150 ft-lbs (160-200 n·m) cone m14 x 1.50 22 mm 130-160 ft-lbs (190-220 n·m) flanged **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before t...

  • Page 463

    Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts. Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated again...

  • Page 464

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to...

  • Page 465

    Warning! (continued) vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. 4500/5500 models these vehicles do not come equipped with a jack. Note: jacking and tire changing on 4500/5500 models should be performed by an authorized dealer...

  • Page 466

    6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For ex- ample, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jacking instructions instructions warning! Carefu...

  • Page 467

    Warning! (continued) • if working on or near a roadway, be extremely careful of motor traffic. • to assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. Caution! Do not attempt to raise the vehicle by jacking on locations other ...

  • Page 468

    1. If equipped, remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. When changing the front wheel, assemble the jack drive tube to the jack and ...

  • Page 469

    Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. Note: if the jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. 4. ...

  • Page 470

    6. Using the wheel wrench, finish tightening the nuts using a crisscross pattern. For the proper lug nut torque specifications refer to “wheel and tire torque specifications” in this section. If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or...

  • Page 471

    For single rear wheel (srw) models, use the flat blade on the end of the lug wrench to pull the hub cap off. Insert the blade end into the pull off notch and carefully pull the hub cap off with a back and forth motion. On 3500 models with dual rear wheels (drw), you must first remove the hub caps. T...

  • Page 472

    Dual rear wheels slots in the wheels will assist in properly orienting the inner and outer wheels. Align these slots when assem- bling the wheels for best access to the tire valve on the inner wheel. The tires of both dual wheels must be completely off the ground when tightening to insure wheel cent...

  • Page 473

    Caution! Never use a floor jack directly under the differential housing of a loaded truck or damage to your vehicle may result. Jump-starting procedures if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portab...

  • Page 474

    Battery (gas model shown) 1 — positive battery post 2 — fuses battery (diesel model shown) 1 — positive battery post 2 — fuses 472 what to do in emergencies.

  • Page 475

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 476

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. Note: do not jump off fuses...

  • Page 477

    Caution! Do not connect jumper cable to any of the fuses on the positive battery terminal. The resulting electrical current will blow the fuse. 6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the j...

  • Page 478

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand, or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse (with automatic transmission) or 2nd gear a...

  • Page 479

    Caution! (continued) • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no trans- mission shifting occurring). Warning! Fast spinning tires can be dangerous....

  • Page 480

    Caution! Tow hooks are for emergency use only to rescue a vehicle stranded off-road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use the ...

  • Page 481

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. If the trans- mission and drivetrain are operable, disabled vehicles may also be towed as described under “recreational towing” in the “starting and operating” section. Towing...

  • Page 482

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 483

    • the towing distance must not exceed 15 miles (24 km). If the transmission is not operable, or the vehicle must be towed faster than 30 mph (48 km/h) or farther than 15 miles (24 km), tow with the rear wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed, or with the front ...

  • Page 484

    Caution! • front or rear wheel lifts must not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when towing. • towing this vehicle in violation of the above re- quirements can cause severe transmission and/or transfer case damage. Damage f...

  • Page 485: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 5.7l . . . . . . . . . .485 䡵 engine compartment — 6.4l . . . . . . . . . .486 䡵 onboard diagnostic system (obd ii) . . .487 ▫ loose fuel filler cap message . . . . . . . . . . . .487 䡵 emissions inspection and maintenance programs . . . . . ....

  • Page 486

    ▫ exhaust system . . . . . . . . . . . . . . . . . . . . . .507 ▫ cooling system . . . . . . . . . . . . . . . . . . . . . .510 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .517 ▫ rear axle and 4x4 front driving axle fluid level . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 487

    Engine compartment — 5.7l 1 — air cleaner filter 6 — battery 2 — automatic transmission dipstick 7 — washer fluid reservoir 3 — engine oil fill 8 — power distribution center (fuses) 4 — engine oil dipstick 9 — coolant pressure cap 5 — brake fluid reservoir 10 — engine coolant reservoir 2 7 maintaini...

  • Page 488

    Engine compartment — 6.4l 1 — coolant pressure bottle 6 — battery 2 — transmission dipstick 7 — power distribution center (fuses) 3 — engine oil fill 8 — washer solvent 4 — engine oil dipstick 9 — power steering fluid reservoir 5 — brake fluid reservoir 10 — air cleaner filter 486 maintaining your v...

  • Page 489

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 490

    (evic)” or “driver information display (did)” in “un- derstanding your instrument panel” for further informa- tion. Tighten the fuel filler cap properly and push the select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose...

  • Page 491

    2. As soon as you cycle the ignition switch to the on position, you will see the malfunction indicator light (mil) symbol come on as part of a normal bulb check. 3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully...

  • Page 492

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 493

    Caution! (continued) components or negatively impact vehicle perfor- mance. Immediately have potential malfunctions examined by an authorized dealer or qualified repair center. • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also all...

  • Page 494

    Caution! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could damage your engine. Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” ...

  • Page 495

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american petroleum institute (api). The manufacturer only recommends api certified engine oils. This symbol certifies 0w-20, 5w- 20, 0w-30, 5w-30 and 10w-30 en- gine oils. Cau...

  • Page 496

    Engine oil viscosity — 6.4l engine use pennzoil ultra™ 0w–40 engine or equivalent mopar® oil meeting the chrysler material standard ms-12633 for use in all operating temperatures. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil...

  • Page 497

    Engine air cleaner filter refer to the “maintenance schedule” for the proper maintenance intervals. Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unles...

  • Page 498

    2. Lift the air cleaner cover to access the air cleaner filter. 5.7l air cleaner filter cover 1 — clean air hose clamp 2 — air hose 3 — spring clips 6.4l air cleaner filter cover 1 — clean air hose clamp 2 — spring clips 496 maintaining your vehicle.

  • Page 499

    3. Remove the air cleaner filter element from the housing assembly. Open air cleaner filter assembly 1 — air cleaner cover 2 — air cleaner filter air cleaner filter 1 — air cleaner filter 2 — air cleaner filter inspection surface 7 maintaining your vehicle 497.

  • Page 500

    Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleaner filter inspection surface facing downward. 2. Install the air clea...

  • Page 501

    Normal. Any belt with cracks running along a rib must be replaced. Also have the belt replaced if it has excessive wear, frayed cords or severe glazing. Conditions that would require replacement: • rib chunking (one or more ribs has separated from belt body) • rib or belt wear • longitudinal belt cr...

  • Page 502

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 503

    Caution! (continued) • if a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables be- fore connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage. Air conditioner maintenance for best possible performance, your air ...

  • Page 504

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r134a — if equipped r-134a air conditioning refrigerant is a hydrofl...

  • Page 505

    Proper maintenance intervals. Use mopar® type ms- 6560 (lithium-based grease), or equivalent. Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated p...

  • Page 506

    Note: life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may be present with chattering, marks, water lines or wet spots. If any of these conditions are present, clean the wiper blades or replace as neces- sary. The wiper blades a...

  • Page 507

    2. To disengage the wiper blade from the wiper arm, press the release tab on the wiper blade and while holding the wiper arm with one hand, slide the wiper blade down towards the base of the wiper arm. Wiper blade with release tab in locked position 1 — wiper blade 2 — wiper arm 3 — release tab wipe...

  • Page 508

    3. With the wiper blade disengaged, remove the wiper blade from the wiper arm. 4. Gently lower the wiper arm onto the glass. Installing the front wipers 1. Lift the wiper arm off of the glass, until the wiper arm is in the full up position. 2. Position the wiper blade near the hook on the tip of the...

  • Page 509

    Reservoir with windshield washer solvent only (not ra- diator antifreeze). When refilling the washer fluid reser- voir, take some washer fluid and apply it to a cloth or towel and wipe the wiper blades clean. This will help blade performance. To prevent freeze-up of your windshield washer system in ...

  • Page 510

    Exhaust system inspected each time the vehicle is raised for lubrication or oil change. Replace as required. Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid ...

  • Page 511

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 512

    Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiat...

  • Page 513

    Cooling system — drain flush and refill if the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old engine coolant (anti...

  • Page 514

    Caution! (continued) rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (an-...

  • Page 515

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: • some vehicles require special tools to add coolant properly. Failure to fill these systems prop...

  • Page 516

    Warning! (continued) • do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result. Disposal of used engine coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your lo...

  • Page 517

    2. Lift and remove the plastic dipstick from the reservoir neck. 3. Check the coolant level on the dipstick. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing en- gine coolant (antif...

  • Page 518

    Of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Checking coolant level — 6.4l eng...

  • Page 519

    • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (anti- freeze) needs to be added, the contents of the coolant expansion bottle must also be protected against freez- ing. • if frequent engine coolant (antifreeze) additions are required, the cool...

  • Page 520

    Warning! (continued) high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency. Brake fluid level check the fluid level of the master cylinder should be checked when performing under the hood service or immediately if the...

  • Page 521

    Warning! (continued) original factory installed hydraulic master cylinder reservoir. • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a ...

  • Page 522

    When checking the fluid level (4500/5500 only), the vehicle should be in a level position. The fluid level should be ¼ in ± ¼ in (6.4 mm ± 6.4 mm) below the fill hole on the front axle. The fluid level should be level with the bottom of the fill hole on the rear axle. Drain and refill on 4500/5500 v...

  • Page 523

    Lubricant selection refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Note: the presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encount...

  • Page 524

    Only the manufacturer’s specified transmission fluid. Refer to “fluids, lubricants, and genuine parts” in this section for fluid specifications. It is important to maintain the transmission fluid at the correct level using the recommended fluid. No chemical flushes should be used in any transmission...

  • Page 525

    Fluid level check check the fluid level when the engine is fully warmed up and the transmission fluid is at normal operating tem- perature. Driving with an improper fluid level will greatly reduce the life of the transmission and of the fluid. Check the fluid level whenever the vehicle is serviced. ...

  • Page 526

    4. Fully apply the parking brake and press the brake. 5. Place the shift lever momentarily into each gear posi- tion (allowing time for the transmission to fully en- gage in each position), ending with the transmission in park. 6. Wipe the area around the dipstick clean to prevent dirt from entering...

  • Page 527

    Caution! If the fluid temperature is below 50°f (10°c) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. Run the engine at idle, in park, to warm the fluid. 9. Reinsert the dipstick. Check for leaks. Release the parking bra...

  • Page 528

    Extreme hot or cold weather and other extreme condi- tions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Cor...

  • Page 529

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 530

    Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral ph) soap and water to maintain their luster and to prevent corrosion. Wash wheels with the same soap solution recommended for the body of the vehicle. Yo...

  • Page 531

    Damage this finish and such damage is not covered by the new vehicle limited warranty. Caution! Do not use scouring pads, steel wool, a bristle brush, metal polishes or oven cleaner. These products may damage the wheel’s protective finish. Such damage is not covered by the new vehicle limited warran...

  • Page 532

    • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar® total clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar® multi-purpose cleaner to a clean, damp cloth and remov...

  • Page 533

    Caution! Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage. Wipe away immediately. Caution! Damage caused by these type of products may not be covered by your new vehicle l...

  • Page 534

    Cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or windows equipped with radio antennas. Do not use scrapers or other sharp instrument that may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using...

  • Page 535

    Warning! (continued) assemblies must be replaced after a collision if they have been damaged (i.E., bent retractor, torn web- bing, etc.). Fuses warning! • when replacing a blown fuse, always use an ap- propriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse wi...

  • Page 536

    Power distribution center the power distribution center is located in the engine compartment near the battery. This center contains car- tridge fuses, micro fuses, relays, and circuit breakers. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number o...

  • Page 537

    Cavity cartridge fuse micro fuse description f06 40 amp green antilock brakes/electronic stability con- trol pump f07 40 amp green starter solenoid f08 20 amp blue (1500 ld/cummins die- sel) emissions diesel – if equipped f09 40 amp green (special services vehicle & cummins diesel) 30 amp pink (1500...

  • Page 538

    Cavity cartridge fuse micro fuse description f11 30 amp pink integrated trailer brake module – if equipped f12 40 amp green body controller #3 / interior lights f13 40 amp green blower motor f14 40 amp green body controller #4 / power locks f16 30 amp pink smart bar – if equipped f19 20 amp blue (15...

  • Page 539

    Cavity cartridge fuse micro fuse description f24 30 amp pink driver door module f25 30 amp pink front wiper f26 30 amp pink antilock brakes/stability control module/valves f28 20 amp blue trailer tow backup lights – if equipped f29 20 amp blue trailer tow parking lights – if equipped f30 30 amp pink...

  • Page 540

    Cavity cartridge fuse micro fuse description f37 30 amp pink cummins diesel fuel heater #2 if equipped f38 30 amp pink power inverter 115v ac– if equipped f39 30 amp pink vehicle system interface module #1– if equipped f41 10 amp red active grill shutter — if equipped f42 20 amp yellow horn f44 10 a...

  • Page 541

    Cavity cartridge fuse micro fuse description f54 20 amp yellow adjustable pedals f56 15 amp blue additional diesel content – if equipped f57 20 amp yellow transmission f58 20 amp yellow spare fuse f59 10 amp red scr relay – if equipped f60 15 amp blue underhood lamp f61 10 amp red (1500 ld diesel & ...

  • Page 542

    Cavity cartridge fuse micro fuse description f66 10 amp red sunroof / passenger window switches / rain sensor f67 10 amp red cd / dvd / bluetooth hands-free mod- ule – if equipped f69 15 amp blue mod scr 12v (cummins diesel) – if equipped f70 30 amp green fuel pump motor f71 25 amp clear amplifier f...

  • Page 543

    Cavity cartridge fuse micro fuse description f75 10 amp red coolant temperature valve actuator f76 10 amp red antilock brakes/electronic stability con- trol f77 10 amp red drivetrain control module/front axle disconnect module f78 10 amp red engine control module / electric power steering f79 15 amp...

  • Page 544

    Cavity cartridge fuse micro fuse description f87 10 amp red air suspension-if equipped / trailer tow / steering column control module f88 15 amp blue instrument panel cluster f90/f91 20 amp yellow power outlet (rear seats) customer select- able f93 20 amp yellow cigar lighter f94 10 amp red shifter ...

  • Page 545

    Cavity cartridge fuse micro fuse description f101 15 amp blue electrochromatic mirror / smart high beams – if equipped f104 20 amp yellow power outlets (instrument panel/center console) caution! • when installing the power distribution center cover, it is important to ensure the cover is properly po...

  • Page 546

    • any time you store your vehicle or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage w...

  • Page 547

    Bulb number center high mounted stop lamp 921 rear cargo lamp 921 box off tail lamps – stop/turn/tail/license plate 1157 box off tail lamps – back up 1156 bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to...

  • Page 548

    7. Reach into the front wheel house ahead of the front wheel, remove the fastener, and lift the cover over the access hole in the front of the wheel house splash shield. Access to the rear of the lamp can be gained through this access hole. 8. Reach through the access hole of the wheel house splash ...

  • Page 549

    9. Remove the headlamp assembly. Grasp the outboard edge of the lamp and pull it straight forward to disengage the ball stud from the plastic grommet. 10. Disconnect the wiring harness connectors from the bulb socket. 11. Replace bulb(s) as necessary. Caution! • do not contaminate the bulb glass by ...

  • Page 550

    Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. Center high-mounted stoplamp (chmsl) with cargo lamp 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the ...

  • Page 551

    3. Turn the desired bulb socket ¼ turn and remove the socket and bulb from housing. 4. Pull the desired bulb straight from the socket. Chmsl connector location chmsl bulb and socket 7 maintaining your vehicle 549.

  • Page 552

    Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • outside bulbs: cargo lamps • inside bulb: center high-mounted stop lamp 5. Reverse the procedure for installation of bulbs and housing. Cab...

  • Page 553

    2. Rotate the bulb socket ¼ turn and pull it from the lamp assembly. 3. Pull the bulb straight from it’s socket and replace. Removing bulb socket from clearance lamp removing the bulb from the bulb socket 7 maintaining your vehicle 551.

  • Page 554

    Fluid capacities u.S. Metric fuel (approximate) standard rear tank 52 gallons 197 liters optional midship tank 22 gallons 83 liters engine oil with filter 5.7l engine (we recommend you use sae 5w-20, api certified) 7 quarts 6.6 liters 5.7l engine (we recommend you use sae 5w-30, api certified) for 3...

  • Page 555

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10–year/150,000 mile formula oat (organic additive technology). Engine oil – 5.7l engine we recommend you use api certified sae 5w-20 en- gine oil, m...

  • Page 556

    Component fluid, lubricant, or genuine part engine oil – 6.4l engine for best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet the american petroleum institute (api) categories of sn. The manufacturer re...

  • Page 557

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 558

    Chassis component fluid, lubricant, or genuine part automatic transmission (5.7l, and 6.4l engine with 66rfe transmission) (for diesel engine see diesel supplement) use only atf+4® automatic transmission fluid. Fail- ure to use atf+4® fluid may affect the function or performance of your transmission...

  • Page 559: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .558 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .560 8.

  • Page 560

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 561

    Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire inflation pressures and look for unusual wear or damage • check the fluid levels of the coolant reservoir, brake master cylinder, power steering and automatic trans- mission and fill a...

  • Page 562

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176...

  • Page 563

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 564

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 565

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 566

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 567: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .567 ▫ prepare for the appointment. . . . . . . . . . . . .567 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .567 ▫ be reasonable with requests ....

  • Page 568

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .573 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .573 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .573 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .574 566 if...

  • Page 569

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 570

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 571

    In mexico contact av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has instal...

  • Page 572

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 573

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 574

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 575

    Call toll free at: • 1-800-890-4038 (u.S.) • 1-800-387-1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 576

    Concrete. A tire marked c may have poor traction perfor- mance. Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades...

  • Page 577: Index

    Index 10

  • Page 578

    Adding engine coolant (antifreeze) . . . . . . . . . . . .512 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .423 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .421 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . . .164 air bag. . . . . . . ...

  • Page 579

    Automatic door locks . . . . . . . . . . . . . . . . . . . . . .38 automatic headlights . . . . . . . . . . . . . . . . . . . . . .148 automatic high beams . . . . . . . . . . . . . . . . . . . . .151 automatic temperature control (atc) . . . . . . . . . .302 automatic transmission . . . . . . . . ....

  • Page 580

    Radiator (coolant pressure) . . . . . . . . . . . . . . . .513 carbon monoxide warning . . . . . . . . . . . . . . .107, 423 cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 car washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .526 cellular phone . . . . . . . ....

  • Page 581

    Coolant pressure cap (radiator cap) . . . . . . . . . . .513 cooling system. . . . . . . . . . . . . . . . . . . . . . . . . . .510 adding coolant (antifreeze) . . . . . . . . . . . . . . .512 coolant capacity . . . . . . . . . . . . . . . . . . . . . . .552 coolant level . . . . . . . . . . . . . ....

  • Page 582

    Dual rear wheels . . . . . . . . . . . . . . . . . .408, 460, 470 electrical power outlets. . . . . . . . . . . . . . . . . . . . .174 electric rear window defrost. . . . . . . . . . . . . . . . .190 electronically shifted transfer case. . . . . . . . . . . . .354 electronic brake control system . ....

  • Page 583

    Oil synthetic . . . . . . . . . . . . . . . . . . . . . . . . . .494 overheating . . . . . . . . . . . . . . . . . . . . . . . . . . .458 engine oil viscosity . . . . . . . . . . . . . . . . . . . . . . .494 enhanced accident response feature . . . . . . . . . . . .71 entry system, illuminated . . ....

  • Page 584

    Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .420 filler cap (gas cap) . . . . . . . . . . . . . . . . . . . . .424 filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .553 gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .419 materials added ....

  • Page 585

    Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 head restraints . . . . . . . . . . . . . . . . . . . . . . . . . .136 heated mirrors . . . . . . . . . . . . . . . . . . . . . . .125, 190 heater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284, 290 high beam/low ...

  • Page 586

    Lock the vehicle’s doors . . . . . . . . . . . . . . . . . .270 passive entry . . . . . . . . . . . . . . . . . . . . . . . . . . .40 passive entry programming . . . . . . . . . . . . .40, 270 unlock liftgate . . . . . . . . . . . . . . . . . . . . . . . . .270 keyless entry system . . . . . . . . ....

  • Page 587

    High beam . . . . . . . . . . . . . . . . . . . . . . . .159, 199 high beam indicator . . . . . . . . . . . . . . . . . . . . .199 high beam/low beam select . . . . . . . . . . . . . . .159 illuminated entry . . . . . . . . . . . . . . . . . . . . . . . .23 instrument cluster . . . . . . . . . . . ....

  • Page 588

    Electric powered . . . . . . . . . . . . . . . . . . . . . . . .123 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140 outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 rearview . . . . . ...

  • Page 589

    Paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .525 panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 parking brake. . . . . . . . . . . . . . . . . . . . . . . . . . . .366 passing light . . . . . . . . . . . . . . . . . . . . . . . . . . . .159 passive...

  • Page 590

    Shifting into transfer case neutral (n) . . . . . . . .452 shifting out of transfer case neutral (n) . . . . . .454 reformulated gasoline . . . . . . . . . . . . . . . . . . . . .420 refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .502 reminder, seat belt. . . . . . . . . . . ....

  • Page 591

    Seat belt reminder . . . . . . . . . . . . . . . . . . . . . . .50 seat belt system . . . . . . . . . . . . . . . . . . . . . . . . .48 seat belt maintenance . . . . . . . . . . . . . . . . . . . . . .532 seat belt reminder . . . . . . . . . . . . . . . . . . . . . . . . .50 seat belts . . . . . . ....

  • Page 592

    Shift lever override . . . . . . . . . . . . . . . . . . . . . . .478 shoulder belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 signals, turn . . . . . . . . . . . . . . . . . . . . . .110, 158, 199 sliding rear window power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 593

    Tire and loading information placard . . . .387, 388, 405 tire markings . . . . . . . . . . . . . . . . . . . . . . . . . . . .381 tires . . . . . . . . . . . . . . . . . . . . . . . . . . . .110, 392, 573 aging (life of tires) . . . . . . . . . . . . . . . . . . . . .402 air pressure . . . . . . . ...

  • Page 594

    Trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . .427 cooling system tips . . . . . . . . . . . . . . . . . . . . .445 hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .432 minimum requirements . . . . . . . . . . . . . . . . . .435 mirrors . . . . . . . . . . . . ...

  • Page 595

    Vehicle modifications/alterations . . . . . . . . . . . . . . .7 vehicle storage. . . . . . . . . . . . . . . . . . . . . . . .305, 543 viscosity, engine oil . . . . . . . . . . . . . . . . . . . . . . .494 voice recognition system (vr) . . . . . . . . . . . . . . . .307 warning lights (instrument c...

  • Page 596

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 597

    C h a s s i s c a b o w n e r ’ s m a n u a l 2 0 1 5 2015 chassis cab 15dd43-126-ae fifth edition printed in u.S.A. Fca us llc.