1. DL manuals
  2. RAM
  3. Automobile
  4. Chassis CAB 2018
  5. Owner's Manual

RAM Chassis CAB 2018 Owner's Manual

Summary of Chassis CAB 2018

  • Page 1

    Stick with the specialists ® second edition rev 1 printed in the u.S.A. ©2017 fca us llc. All rights reserved. Ram is a registered trademark of fca us llc. 18dd-126-ab c h a s s i s c a b o w n e r ’ s m a n u a l 2 0 1 8 promaster 2018.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 graphical table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . . .5 ▫ essential information . . . . . . . . . . . . . . . . . . . . . .5 ▫ symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 䡵 warnings and...

  • Page 6

    Introduction dear customer, congratulations on selecting your new vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality. This is a specialized utility vehicle. It can go places and perform tasks that conventional passenger vehicles are not intended. It...

  • Page 7

    Described for technical and/or commercial reasons. For further information, contact an authorized dealer. If applicable, refer to the owners manual supplement for related information. Note: after reviewing the owner’s information, it should be stored in the vehicle for convenient referencing, and re...

  • Page 8

    Symbols consult the following table for a description of the symbols that may be used on your vehicle or throughout this owner’s manual: 6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may mi...

  • Page 11

    Graphical table of contents contents 䡵 front view . . . . . . . . . . . . . . . . . . . . . . . . . . .10 䡵 rear view. . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 䡵 instrument panel . . . . . . . . . . . . . . . . . . . . .12 䡵 interior . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 12

    Front view front view 1 — exterior mirrors 4 — windshield 2 — doors 5 — headlights 3 — wheels/tires 6 — hood/engine compartment 10 graphical table of contents.

  • Page 13

    Rear view rear view 1 — rear lights 2 graphical table of contents 11.

  • Page 14

    Instrument panel instrument panel 1 — air vents 4 — instrument cluster 2 — multifunction lever 5 — radio 3 — steering wheel 12 graphical table of contents.

  • Page 15

    Interior interior 1 — door locks/window switches 4 — switch panel 2 — seats 5 — climate controls 3 — gear selector 2 graphical table of contents 13.

  • Page 17

    Getting to know your vehicle contents 䡵 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 ▫ key fobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 䡵 ignition switch . . . . . . . . . . . . . . . . . . . . . . .25 ▫ wireless ignition node (win) — if equipped. . . ...

  • Page 18

    ▫ automatic door locks — if equipped . . . . . . . .39 ▫ child-protection door lock . . . . . . . . . . . . . . . .40 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 ▫ manual front seat adjustment . . . . . . . . . . . . . .42 ▫ manual rear seat adjustment . . . . . . . . ....

  • Page 19

    ▫ tilt side mirrors in reverse — if equipped . . . . .66 ▫ illuminated vanity mirror — if equipped . . . . . .66 䡵 exterior lights . . . . . . . . . . . . . . . . . . . . . . .67 ▫ headlight switch . . . . . . . . . . . . . . . . . . . . . . .67 ▫ headlights . . . . . . . . . . . . . . . . . . . . ....

  • Page 20

    ▫ operating tips . . . . . . . . . . . . . . . . . . . . . . . . .93 䡵 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 ▫ power windows — if equipped . . . . . . . . . . . . .96 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . . . .98 䡵 hood . . . . . . . . . . . . . ....

  • Page 21

    Keys key fobs your vehicle uses either a wireless ignition node system or keyless ignition system. The ignition system consists of a key fob with a remote keyless entry (rke) and an ignition switch. The keyless ignition system consists of a key fob and keyless enter-n-go button. Note: the key fob ma...

  • Page 22

    This keyless push button ignition key fob allows the driver to operate the ignition switch with the push of a button, as long as the key fob is in the passenger compartment. The keyless push button ignition has four operating positions, three of which are labeled and will illuminate when in position...

  • Page 23

    Note: inserting the key fob with integrated key into the ignition switch disables the system from responding to any button pushes from that key fob. Driving at speeds 5 mph (8 km/h) and above disables the system from responding to all key fob buttons for all key fobs. To unlock the doors and tailgat...

  • Page 24

    To lock the doors and tailgate push and release the lock button on the key fob to lock all doors, and the tailgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Sound horn with remote key lock this feature will cause the horn to chirp when the doors are locked...

  • Page 25

    Note: • perchlorate material — special handling may apply. See www.Dtsc.Ca.Gov/hazardouswaste/perchlorate • do not touch the battery terminals that are on the back housing or the printed circuit board. 1. Remove the emergency key by sliding the mechanical latch on the back of the key fob sideways wi...

  • Page 26

    2. Separating key fob halves requires screw removal – if equipped, and gently prying the two halves of the key fob apart. Make sure not to damage the seal during removal. Remove screw from key fob case separating win key fob case 24 getting to know your vehicle.

  • Page 27

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the b...

  • Page 28

    Detents and one that is spring-loaded. The detent positions are off, acc, and on/run. The start position is a spring-loaded momentary contact position. When released from the start position, the switch automatically returns to the on/run position. Removing key fob from the (win) ignition place the g...

  • Page 29

    Warning! • before exiting a vehicle, always shift the automatic transmission into park or the manual transmission into reverse, apply the parking brake, turn the vehicle off, remove the key fobs from the vehicle, and lock all doors. If equipped with keyless enter- n-go, always make sure the keyless ...

  • Page 30

    Caution! An unlocked vehicle is an invitation. Always remove the key from the ignition and lock all doors when leaving the vehicle unattended. Keyless push button ignition — if equipped this feature allows the driver to operate the ignition switch with the push of a button as long as the remote keyl...

  • Page 31

    Note: • ⬙ keyed ⬙ ignition systems will chime in off or acc when the driver door is open. • “keyless ⬙ ignition systems will chime in acc or run when the driver door is open. • the instrument cluster display will display “key in ignition.” remote start — if equipped how to use remote start all of th...

  • Page 32

    The instrument cluster display message stays active until the ignition is turned to the on/run position. To enter remote start mode push and release the remote start button on the key fob twice within five seconds. The parking lights will flash, vehicle doors will lock, and the horn will chirp twice...

  • Page 33

    Note: the remote start comfort system can be activated and deactivated through the uconnect system. Refer to “uconnect settings” in “multimedia” for further informa- tion on remote start comfort system operation. General information the following regulatory statement applies to all radio frequency (...

  • Page 34

    An invalid key fob to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds. If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electro...

  • Page 35

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 36

    The vehicle security alarm will set when you use the power door locks, or use the key fob to lock the doors. After all the doors are locked and closed, the vehicle security light, in the instrument panel cluster, will flash rapidly for about 16 seconds to indicate that the alarm is being set. After ...

  • Page 37

    Doors manual door locks front and rear doors may be locked by moving the lock knob down or unlocked by moving the lock knob up. Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed. The emergency key will unlo...

  • Page 38

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the key fob in or near the ...

  • Page 39

    Enter-n-go. This feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons. Note: • passive entry may be programmed on/off. Refer to “uconnect settings” in “multimedia” for further infor- mation. • if wearing gloves on your hands, or if it ...

  • Page 40

    To unlock from the passenger side: with a valid passive entry key fob within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all doors automatically. The interior door panel lock knob will raise when the door is unlocked. Note: all doors will unlock when the...

  • Page 41

    Note: • after pushing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • the pass...

  • Page 42

    Authorized dealer per written request of the customer. Please see your authorized dealer for service. Automatic doors unlock — if equipped this feature unlocks all of the doors of the vehicle when either front door is opened. This will occur only after the vehicle has been shifted into the park posi...

  • Page 43

    Warning! Avoid trapping anyone in the vehicle in a collision. Remember that the sliding doors cannot be opened from the inside door handle when the child protection door locks are engaged. Note: • after setting the child-protection door lock system, always test the door from the inside to make certa...

  • Page 44

    Manual front seat adjustment manual front seat forward/rearward adjustment both front seats are adjustable forward or rearward. The manual seat adjustment handle is located under the seat cushion at the front edge of each seat. While sitting in the seat, pull up on the handle and slide the seat forw...

  • Page 45

    Warning! • do not stand or lean in front of the seat while actuating the handle. The seatback may swing for- ward and hit you causing injury. • to avoid injury, place your hand on the seatback and actuate the handle, then position the seatback in the desired position. 40-20-40 front bench seat — if ...

  • Page 46

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Power driver seat adjustment — if equipped some models may be equipped with an eight-w...

  • Page 47

    Adjusting the seat up or down the height of the seats can be adjusted up or down. Pull upward or push downward on the rear of seat switch, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Tilting the seat up or down the angle of the se...

  • Page 48

    Power lumbar — if equipped vehicles equipped with power driver or passenger seats may be also be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lum...

  • Page 49

    Driver memory seat — if equipped this feature allows the driver to store up to two different memory profiles for easy recall through a memory switch. Each memory profile contains desired position settings for the driver’s seat, side mirrors, adjustable pedals (if equipped) and a set of desired radio...

  • Page 50

    4. Within five seconds, push and release either of the memory buttons (1) or (2). The instrument cluster dis- play will show which memory position has been set. Note: • memory profiles can be set without the vehicle in park, but the vehicle must be in park to recall a memory profile. • to set a memo...

  • Page 51

    Memory position recall note: • for vehicles equipped with an automatic transmission, the vehicle speed must be lower than 5 mph to recall memory positions. If a recall is attempted when the vehicle speed is greater than 5 mph, a message will be displayed in the instrument cluster display. • for vehi...

  • Page 52

    Keyless enter-n-go), the driver’s seat will move about 2.4 inches (60 mm) rearward if the driver’s seat position is greater than or equal to 2.7 inches (67.7 mm) forward of the rear stop. The seat will return to its previously set position when you place the ignition into the acc or run position. • ...

  • Page 53

    Front heated seats the front heated seats control buttons are located within the climate or controls screen of the touchscreen. • press the heated seat button once to turn the hi setting on. • press the heated seat button a second time to turn the lo setting on. • press the heated seat button a thir...

  • Page 54

    Note: • once a heat setting is selected, heat will be felt within two to five minutes. • the engine must be running for the heated seats to operate. When the hi-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output w...

  • Page 55

    Plastic grocery bag retainers (regular cab models) retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear ...

  • Page 56

    Note: do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head. Rear head restraint adjustment the rear seats are equipped with adjustable and removable head restraints. To raise the head restraint, pull upward on t...

  • Page 57

    Note: • the rear center head restraint (crew cab and quad cab) has only one adjustment position that is used to aid in the routing of a tether. Refer to “occupant restraints” in “safety” for further information. • do not reposition the head restraint 180 degrees to the incorrect position in an attem...

  • Page 58

    Warning! • a loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow re- moved head restraints in a location outside the occupant compartment. • all the head restraints must be reinstalled in the vehicle to...

  • Page 59

    Heated steering wheel — if equipped the steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on, it will operate for an average of 80 minutes before automatical...

  • Page 60

    The adjustable pedal switch is located to the left side of the steering column. • the pedals can be adjusted with the ignition off. • the pedals cannot be adjusted when the vehicle is in reverse or when the speed control system is on. The following messages will appear on vehicles equipped with an i...

  • Page 61

    Caution! Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjust- able pedal’s path. Mirrors inside day/night mirror — if equipped the mirr...

  • Page 62

    • press the mirror dimmer button once to turn the feature on. • press the mirror dimmer button a second time to turn the feature off. Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the...

  • Page 63

    When the vehicle is placed into reverse gear, a video display illuminates to display the image generated by the rear view camera located on the tailgate handle. The auto dimming feature is also disabled to improve rear view viewing. Outside mirrors to receive maximum benefit, adjust the outside mirr...

  • Page 64

    Power mirrors — if equipped the controls for the power mirrors are located on the driver’s door trim panel. The power mirror controls consist of mirror select buttons and a four-way mirror control switch. To adjust a mirror, push either the l (left) or r (right) button to select the mirror that you ...

  • Page 65

    Power folding outside mirrors for standard and trailer tow — if equipped if equipped with power folding mirrors, they can be electrically folded rearward and unfolded into the drive position. The switch for the power folding mirrors is located be- tween the power mirror switches l (left) and r (righ...

  • Page 66

    • the mirrors come out of the unfolded position. • the mirrors shake and vibrate at normal driving speeds. To reset the power folding mirrors: 1. Using the power folding mirror switch, move the mirror to its full forward position. 2. Using the power folding mirror switch, move the mirror to the full...

  • Page 67

    Trailer towing mirrors — if equipped these mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped in or out). Note: fold the trailer towing mirrors rearward...

  • Page 68

    Tilt side mirrors in reverse — if equipped tilt side mirrors in reverse provides automatic outside mirror positioning which will aid the driver’s view of the ground rearward of the front doors. The outside mirrors will move slightly downward from the present position when the vehicle is shifted into...

  • Page 69

    “slide-on-rod” features of sun visor — if equipped the sun visor “slide-on-rod” feature allows for additional flexibility in positioning the visor to block out the sun. To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until t...

  • Page 70

    Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less suscep- tible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens clean- ing procedures must be followed. To minimize the possibilit...

  • Page 71

    Daytime running lights (drl) — if equipped the headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except park. This provides a constant ⬙ lights on ⬙ condition until the ignition is turned off. The lights illuminate at less than half of normal i...

  • Page 72

    Note: • the automatic high beam headlamp control can be turned on or off by selecting “on” under “auto high beam” within your uconnect settings, as well as turning the headlight switch to the auto position. Refer to “uconnect settings” in “multimedia” for further information. • broken, muddy, or obs...

  • Page 73

    Off position. The headlight time delay can be pro- grammed 0/30/60/90 seconds. Refer to “uconnect set- tings” in “multimedia” for further information. To turn the automatic system off, move the headlight switch out of the auto position. Note: the engine must be running before the headlights will tur...

  • Page 74

    Headlight delay to aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for approximately up to 90 seconds. This delay is initiated when the ignition is turned off while the headlight switch is on, and then the headlight switch is cycled off. Headlight ...

  • Page 75

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster display will flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defect...

  • Page 76

    Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. If the ignition is off and any door is left ajar for 10 minutes or the dimmer control is rotated all the way up to the dome on position for 10 minutes, the interior light...

  • Page 77

    Note: the courtesy/reading lights will remain on until the switch is pushed a second time, so be sure they have been turned off before exitingthe vehicle. If the interior lights are left on after the ignition is turned off, they will automatically turn off after 15 minutes. Ambient light the overhea...

  • Page 78

    “party mode” when a door is open and the interior lights are on, rotating the dimmer control all the way left, to the off detent, will cause all the interior lights to go out. This is also known as the ⬙ party ⬙ mode because it allows the doors to stay open for extended periods of time without disch...

  • Page 79

    Note: if your vehicle is equipped with illuminated ap- proach lights under the outside mirrors, they can be turned off by moving the instrument panel dimmer into the “dome defeat” detent position. Windshield wipers and washers windshield wipers the wipers and washers are operated by a switch in the ...

  • Page 80

    If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected. If the washer knob is pushed while in the off position, the wiper will turn on and cycle approxim...

  • Page 81

    Wiper sensitivity. Positions 4 and 5 can be used if the driver desires more sensitivity. Place the wiper switch in the o (off) position when not using the system. Note: • the rain sensing feature will not operate when the wiper switch is in the low or high-speed position. • the rain sensing feature ...

  • Page 82

    Climate controls manual climate controls without touchscreen the controls for the manual heating and air conditioning system in this vehicle consist of a series of outer rotary dials and inner push knobs. These comfort controls can be set to obtain desired interior conditions. Manual climate control...

  • Page 83

    Icon description recirculation button push and release this button to change the system between recirculation mode and outside air mode. Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present. Note: • continuous use of the recirculation mode may ma...

  • Page 84

    Icon description temperature control use this control knob to regulate the temperature of the air inside the passenger compartment. Rotating the knob counterclockwise, from top center into the blue area of the scale, indicates cooler temperatures. Rotating the knob clockwise, into the red area, indi...

  • Page 85

    Icon description floor mode floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix mode mix mode air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy c...

  • Page 86

    Manual climate controls with a touchscreen uconnect 4c/4c nav with manual temperature controls 84 getting to know your vehicle.

  • Page 87

    Automatic climate controls with a touchscreen uconnect 3 with 5–inch display with automatic temperature controls 3 getting to know your vehicle 85.

  • Page 88

    Uconnect 4c/4c nav with automatic temperature controls 86 getting to know your vehicle.

  • Page 89

    Control descriptions note: icons and descriptions can vary based upon vehicle equipment. Icon description max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manua...

  • Page 90

    Icon description auto button — if equipped automatically controls the interior cabin temperature by adjusting airflow distribution and amount. Toggling this function will cause the system to switch between manual mode and auto- matic modes. Refer to “automatic operation” for more information. Front ...

  • Page 91

    Icon description uconnect 3 uconnect 4c/4c nav driver and passenger temperature up and down buttons provides the driver and passenger with independent temperature control. Push the up arrow button on the faceplate, press the up arrow button on the touchscreen, or press and slide the temperature bar ...

  • Page 92

    Icon description touchscreen buttons • faceplate: the blower speed increases as you turn the blower control knob clockwise from the lowest blower setting. The blower speed decreases as you turn the blower control knob counterclockwise. • touchscreen: use the small blower icon to reduce the blower se...

  • Page 93

    Icon description mix mode mix mode air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Clim...

  • Page 94

    Note: • if fog or mist appears on the windshield or side glass, select defrost mode, and increase blower speed if needed. • if your air conditioning performance seems lower than expected, check the front of the a/c condenser (located in front of the radiator), for an accumulation of dirt or insects....

  • Page 95

    3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system auto...

  • Page 96

    Vacation/storage before you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes, in fresh air with the blower setting on high. This will ensure adequate system lubrication to minimize the possibility of ...

  • Page 97

    Operating tips chart 3 getting to know your vehicle 95.

  • Page 98

    Windows power windows — if equipped the power window controls located on the driver’s door trim panel have up—down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passen- ger window control and on the rear do...

  • Page 99

    To open the window part way, push to the switch to the first detent and release it when you want the window to stop. Auto-up feature with anti-pinch protection (4-door models driver and front passenger door only) — if equipped pull the window switch fully upward to the second detent, release, and th...

  • Page 100

    Down position. To enable the window controls, push the window lock switch again and return the switch to the released or up position. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeti...

  • Page 101

    2. Reach into the opening beneath the center of the hood and push the safety latch lever to the left to release it, before raising the hood. To close the hood lower the hood to approximately 12 inches (30 cm) from the engine compartment and drop it. Make sure that the hood is completely closed. Warn...

  • Page 102

    Note: homelink is disabled when the vehicle security alarm is active. Warning! • your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transcei...

  • Page 103

    For efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the homelink system. To erase the channels place the ignition in the on/run position and push and ho...

  • Page 104

    1. Turn the ignition switch to the on/run position. Note: for vehicles equipped with keyless enter-n-go, place the ignition in the run position with the engine on. Make sure while programming homelink with the engine on that your vehicle is outside of your garage, or that the garage door remains ope...

  • Page 105

    Reprogramming a single homelink button (rolling code) to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Push and hold the desired homelink button until the indicator light begins to flash after 20 seconds. Do not release the...

  • Page 106

    2. Push and hold the desired homelink button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “program- ming a non-rolling code” step 2 and follow all remain- ing steps. Canadian/gate operator programming for programm...

  • Page 107

    5. Push and hold the programmed homelink button. The instrument cluster display will display “channel # transmit.” if the device is plugged in and activates, programming is complete. If you unplugged the garage door opener/device for programming, plug it back in at this time. Reprogramming a single ...

  • Page 108

    Troubleshooting tips if you are having trouble programming homelink, here are some of the most common solutions: • replace the battery in the garage door opener hand- held transmitter. • push the learn button on the garage door opener to complete the training for a rolling code. • did you unplug the...

  • Page 109

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 110

    To open the upper glove compartment, push upward on the handle release. The glove compartment door will automatically open. To open the lower glove compartment, pull the release handle. Upper glove compartment lower glove compartment 108 getting to know your vehicle.

  • Page 111

    Door storage front door storage — if equipped storage areas and bottle holders (driver’s side only) are located in the door trim panels. Rear door storage — if equipped storage compartments are located in both the driver and passenger rear door trim panels. Center storage compartment — if equipped t...

  • Page 112

    Warning! • this armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or a collision. Only use the center seating position when the armrest is fully upright. • in a collision, the latch may open if the total weight of the items stored exceeds about ...

  • Page 113

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a colli- sion. The center console is equipped with a front storage bin located next to the cupholders. This storage bin may be equipped wi...

  • Page 114

    Seatback storage located in the back of both the driver and passenger front seats are pockets that can be used for storage. Second row in-floor storage bin — if equipped in-floor storage bins are located in front of the second row seats and can be used for extra storage. The storage bins have remova...

  • Page 115

    Note: the front seat may have to be moved forward to fully open the lid. Storage bin (regular cab) the storage bin is located behind the front seats and runs the length of the cab. Fold flat load floor — if equipped quad cab and crew cab models with a 60/40 rear seat may be equipped with a folding l...

  • Page 116

    Unfolding the load floor/quad cab 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3. Reverse the procedure to store the load floor. Unfolding the load floor load floor in open position 114 get...

  • Page 117

    Unfolding the load floor/crew cab 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unfold both the legs using the straps. Load floor legs in stowed position load floor legs in opened position 3 getting to know your vehicle 115.

  • Page 118

    3. Lift the front panel until the load floor unfolds into position. 4. Reverse the procedure to store the load floor. Positioning the load floor for storage access under the seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load ...

  • Page 119

    Crew cab — if equipped 4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle. Below rear seat storage (crew cab/quad cab) the crew cab and quad cab models provide additional storage under the rear seats. Lift the seats to access the storage c...

  • Page 120

    Cupholders front seat cupholders for vehicles equipped with bucket seats, two cupholders are located next to the center console storage bin. Vehicles equipped with 40/20/40 seats the cupholders are located on the backside of the center portion of the front seat (20). Fold down the center section of ...

  • Page 121

    Some vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passenger convenience. Electrical power outlets the auxiliary 12 volt (13 amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 volt power...

  • Page 122

    The auxiliary power outlets can be found in the following locations: • lower left and lower right of the center stack when equipped with a bench seat. • center console when equipped with bucket seats. Power outlets — center stack 1 — power outlet 2 — usb port (charge only) power outlet — center cons...

  • Page 123

    • rear of the center console storage compartment — quad cab or crew cab. Power outlet — rear center console power outlet — rear center console fuse 3 getting to know your vehicle 121.

  • Page 124

    When the vehicle is turned off, be sure to unplug any equipment as to not drain the battery of the vehicle. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge. Warning! To avoid serious injury or death: •...

  • Page 125

    Caution! (continued) • after the use of high power draw accessories, or long periods of the vehicle not being started (with acces- sories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery. Cigar lighter and ash receiver...

  • Page 126

    Warning! To avoid serious injury or death: • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Auxiliary switches — if equipped there can be up to five auxiliary ...

  • Page 127

    Getting to know your instrument panel contents 䡵 base instrument cluster . . . . . . . . . . . . . .126 ▫ base instrument cluster descriptions . . . . . . . . .126 䡵 premium instrument cluster . . . . . . . . . .128 ▫ premium instrument cluster descriptions . . . . .128 䡵 instrument cluster display ...

  • Page 128

    Base instrument cluster base instrument cluster descriptions 1. Tachometer • indicates the engine speed in revolutions per minute (rpm x 1000). 2. Instrument cluster display • when the appropriate conditions exist, this display shows the instrument cluster display messages. Refer to “instrument clus...

  • Page 129

    3. Speedometer • indicates vehicle speed. 4. Fuel gauge • the pointer shows the level of fuel in the fuel tank when the ignition is in the on/run position. • the fuel pump symbol points to the side of the vehicle where the fuel door is located. 5. Temperature gauge • the temperature gauge shows engi...

  • Page 130

    Premium instrument cluster premium instrument cluster descriptions 1. Tachometer • indicates the engine speed in revolutions per minute (rpm x 1000). 2. Voltmeter • when the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the b...

  • Page 131

    Pointer moves to either extreme left or right and remains there during normal driving, the electrical system should be serviced. Note: the voltmeter may show a gauge fluctuation at various engine temperatures. This cycling operation is caused by the post-heat cycle of the intake manifold heater syst...

  • Page 132

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “servicing and mainte- nance.” follow the warnings u...

  • Page 133

    Instrument cluster display controls the instrument cluster display features a driver-interactive display that is located in the instrument cluster. The instrument cluster display menu items may consist of the following: • speedometer • vehicle info • fuel economy info • trip a • trip b • audio • tra...

  • Page 134

    • stored messages • screen setup • vehicle settings (not equipped with a uconnect touch- screen radio) the system allows the driver to select information by pushing the following instrument cluster display control buttons located on the left side of the steering wheel: • up arrow button push and rel...

  • Page 135

    Display menu screens the instrument cluster display screens are located in the center portion of the cluster and consists of seven sections: 1. Compass display displays the current direction. Refer to “uconnect set- tings” in “multimedia” for further information. 2. Temperature display displays the ...

  • Page 136

    The instrument cluster display screens are located in the center portion of the cluster and consists of eight sections: 1. Main screen — the inner ring of the display will illuminate in grey under normal conditions, yellow for non critical warnings, red for critical warnings, and white for on demand...

  • Page 137

    • unstored messages until run these messages deal primarily with the remote start feature. This message type is displayed until the ignition is in the run state. Examples of this message type are “remote start aborted - door ajar” and “press brake pedal and push button to start.” • five second unsto...

  • Page 138

    Vehicles not equipped with passive entry 1. Without pushing the brake pedal, cycle the ignition to the on/run position (do not start the engine). 2. Push and release the down arrow button to scroll downward through the main menu to “vehicle info.” 3. Push and release the right arrow button to access...

  • Page 139

    • service electronic braking system • engine temperature hot • battery voltage low • service electronic throttle control • lights on • right turn signal light out • left turn signal light out • turn signal on • sound horn with remote lock: off; 1st press; 2nd press • vehicle not in park • key in ign...

  • Page 140

    • trailer brake disconnected • service transmission • service shifter • engage park brake to prevent rolling • transmission too cold idle with engine on • washer fluid low the reconfigurable telltales section is divided into the white telltales area on the right, yellow telltales in the middle, and ...

  • Page 141

    Fuel economy push and release the up or down arrow button until the fuel economy menu item is highlighted in the instrument cluster display. Push and hold the right arrow button to reset average fuel economy. • current fuel economy gauge • average fuel economy value • range to empty • dual fuel tank...

  • Page 142

    Stored messages push and release the up or down arrow button until the messages menu item is highlighted. This feature shows the number of stored warning messages. Pushing the right arrow button will allow you to see what the stored messages are. When no messages are present, main menu icon will be ...

  • Page 143

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 1 language select language english, spanish, french, italian, german, dutch 2 units units u.S.; metric 3 parksense parksense • notification — sound only; sound & display • front volume — low; me- dium; high ...

  • Page 144

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 13 auto lock doors auto lock doors on; off 14 auto unlock doors auto unlock doors on; off 15 sound horn with remote start horn w/ rmt start on; off 16 sound horn with remote lock horn w/ rmt lock on; off 17 ...

  • Page 145

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 24 aero ride height mode aero mode on; off 25 tire/jack mode tire/jack mode on; off 26 transport mode transport mode on; off 27 wheel alignment mode wheel alignment on; off 28 horn w/ remote lower horn w/ rm...

  • Page 146

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 32 trailer name trailer name • trailer # (# is equal to slot position) • boat • car • cargo • dump • equipment • flatbed • gooseneck • horse • tag • motorcycle • snowmobile • travel • utility • 5th wheel 33 ...

  • Page 147

    Turn menu off — if equipped push and release the right arrow button to exit the main menu. Push and release any instrument cluster display control button to enter the instrument cluster display main menu again. Battery saver on/battery saver mode message — electrical load reduction actions — if equi...

  • Page 148

    • 115v ac power inverter system • audio and telematics system loss of the battery charge may indicate one or more of the following conditions: • the charging system cannot deliver enough electrical power to the vehicle system because the electrical loads are larger than the capability of charging sy...

  • Page 149

    • evaluate the latest driving cycles (distance, driving time and parking time). • the vehicle should have service performed if the mes- sage is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause. Warning lights and messages...

  • Page 150

    Indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. Note: the light may flash momentarily during sharp cornering maneuvers, which change fluid level cond...

  • Page 151

    The transmission into neutral and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if your engine overheats” in “in case of emergency” for further information. — battery charge warning light this light illuminates...

  • Page 152

    — electric power steering fault warning light this light will turn on when there’s a fault with the eps (electric power steering) system. Refer to “power steering” in “starting and operating” for further information. Warning! Continued operation with reduced assist could pose a safety risk to yourse...

  • Page 153

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to...

  • Page 154

    — low washer fluid warning light — if equipped this indicator will illuminate when the windshield washer fluid is low. — tire pressure monitoring system (tpms) warning light the warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recom- mended va...

  • Page 155

    Your vehicle has also been equipped with a tpms malfunc- tion indicator to indicate when the system is not operating properly. The tpms malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute a...

  • Page 156

    If the abs light does not turn on when the ignition is placed in the on/run or acc/on/run position, have the brake system inspected by an authorized dealer. — low coolant level warning light this telltale will turn on to indicate the vehicle coolant level is low. — loose fuel filler cap warning ligh...

  • Page 157

    — cargo light — if equipped the cargo light will illuminate when the cargo light is activated by pushing the cargo light button on the head- light switch. — 4wd low indicator light — if equipped this light alerts the driver that the vehicle is in the four-wheel drive low mode. The front and rear dri...

  • Page 158

    — cruise control set indicator light this light will turn on when the speed control is set to the desired speed. Refer to “speed control” in “starting and operating” for further information. White indicator lights — cruise control on indicator this light will turn on when the speed control is on, bu...

  • Page 159

    Onboard diagnostic system (obd ii) cybersecurity your vehicle is required to have an onboard diagnostic system (obd ii) and a connection port to allow access to information related to the performance of your emissions controls. Authorized service technicians may need to ac- cess this information to ...

  • Page 160

    2. As soon as you cycle the ignition switch to the on position, you will see the “malfunction indicator light (mil)” symbol come on as part of a normal bulb check. 3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about ten seconds and then return to being fu...

  • Page 161

    Safety contents 䡵 safety features . . . . . . . . . . . . . . . . . . . . . .160 ▫ anti-lock brake system (abs) . . . . . . . . . . . . .160 ▫ electronic brake control system . . . . . . . . . . . .161 䡵 auxiliary driving systems . . . . . . . . . . . . .172 ▫ tire pressure monitoring system (tpms) ...

  • Page 162

    Safety features anti-lock brake system (abs) the anti-lock brake system (abs) provides increased vehicle stability and brake performance under most brak- ing conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking. The abs performs a self-check cycle to ...

  • Page 163

    Warning! (continued) • the capabilities of an abs equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user’s safety or the safety of others. Abs is designed to function with the oem tires. Modifica- tion may result in degraded abs performance. Anti-lo...

  • Page 164

    Brake system warning light the red “brake system warning light” will turn on when the ignition is turned to the on/run mode and may stay on for as long as four seconds. If the “brake system warning light” remains on or comes on while driving, it indicates that the brake system is not functioning pro...

  • Page 165

    The following conditions must be met in order for hsa to activate: • the feature must be enabled. • the vehicle must be stopped. • park brake must be off. • driver door must be closed. • the vehicle must be on a sufficient grade. • the gear selection must match vehicle uphill direction (i.E., vehicl...

  • Page 166

    Towing with hsa hsa will also provide assistance to mitigate roll back while towing a trailer. Warning! • if you use a trailer brake controller with your trailer, the trailer brakes may be activated and deactivated with the brake switch. If so, there may not be enough brake pressure to hold both the...

  • Page 167

    6. Push the “esc off” button located in the lower switch bank below the climate control four times within 20 seconds. The “esc off indicator light” should turn on and turn off two times. 7. Rotate the steering wheel back to center and then an additional slightly more than one-half turn to the right....

  • Page 168

    The “esc activation/malfunction indicator light” located in the instrument cluster will start to flash as soon as the esc system becomes active. The “esc activation/malfunction indicator light” also flashes when the tcs is active. If the “esc activation/malfunction indicator light” begins to flash d...

  • Page 169

    Partial off the “partial off” mode is intended for times when a more spirited driving experience is desired. This mode may modify tcs and esc thresholds for activation, which allows for more wheel spin than normally allowed. This mode may be useful if the vehicle becomes stuck. To enter the “partial...

  • Page 170

    Warning! • in the esc “full off” mode, the engine torque reduction and stability features are disabled. There- fore, enhanced vehicle stability offered by the esc system is unavailable. In an emergency evasive ma- neuver, the esc system will not engage to assist in maintaining stability. Esc “full o...

  • Page 171

    Note: • the “esc activation/malfunction indicator light” and the “esc off indicator light” come on momentarily each time the ignition is turned on. • each time the ignition is turned on, the esc system will be on even if it was turned off previously. • the esc system will make buzzing or clicking so...

  • Page 172

    Note: tsc cannot stop all trailers from swaying. Always use caution when towing a trailer and follow the trailer tongue weight recommendations. Refer to “trailer tow- ing” in “starting and operating” for further information. When tsc is functioning, the “esc activation/ malfunction indicator light” ...

  • Page 173

    • r = 0.6 mph (1 km/h) • n = 1.2 mph (2 km/h) • d = 0.6 mph (1 km/h) • 1st = 0.6 mph (1 km/h) • 2nd = 1.2 mph (2 km/h) • 3rd = 1.8 mph (3 km/h) • 4th = 2.5 mph (4 km/h) • 5th = 3.1 mph (5 km/h) • 6th = 3.7 mph (6 km/h) • 7th = 4.3 mph (7 km/h) • 8th = 5.0 mph (8 km/h) • 9th = 5.6 mph (9 km/h) – if e...

  • Page 174

    • the vehicle is driven greater than 20 mph (32 km/h) for greater than 70 seconds. • the vehicle is driven greater than 40 mph (64 km/h) (hdc exits immediately). • hdc detects excessive brake temperature. Feedback to the driver the instrument cluster has an hdc icon and the hdc switch has an led ico...

  • Page 175

    Tire pressure will also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pressure. The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature eff...

  • Page 176

    Caution! (continued) • using aftermarket tire sealants may cause the tire pressure monitoring system (tpms) sensor to be- come inoperable. After using an aftermarket tire sealant it is recommended that you take your vehicle to an authorized dealership to have your sensor function checked. • after in...

  • Page 177

    • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the “tire pressure monitoring telltale light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the instrument ...

  • Page 178

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will no longer flash, and the ⬙ service tpm system ⬙ message will no longer display, and a pressure value will dis...

  • Page 179

    Vehicles with non matching full size spare or compact spare • the non matching full size spare or compact spare tire does not have a tpm sensor. Therefore, the tpms will not monitor the pressure in the non matching full size spare or compact spare tire. • if you install the non matching full size sp...

  • Page 180

    Note: it is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure. The tpis consists of the following components: • receiver module • four tpm sensors (single rear wheel [srw] applica- tions) • six tpm sensors (dual ...

  • Page 181

    Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: occupant restraint systems features...

  • Page 182

    6. All occupants should always wear their lap and shoul- der belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate. 8. Do not lean against the door or window. If your vehicle has side air bags, and deployment occu...

  • Page 183

    A few seconds. If the driver or outboard front seat passen- ger (if equipped with outboard front passenger seat beltalert) is unbuckled when the ignition switch is first in the start or on/run position the seat belt reminder light will turn on and remain on until both outboard front seat belts are b...

  • Page 184

    Lap/shoulder belts all seating positions except the crew cab front center seating position have combination lap/shoulder belts. The seat belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoulder part of the seat belt to move freely with you under ...

  • Page 185

    Warning! • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not protect you pro...

  • Page 186

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the sea...

  • Page 187

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automatically ...

  • Page 188

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 189

    First row center seat belt operating instructions (regular cab only) the first row center seat belt (regular cab only) features a seat belt with a mini-latch plate and buckle, which allows the seat belt to detach from the lower anchor when the seat is folded. The latch plate and regular latch plate ...

  • Page 190

    6. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 7. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 191

    Warning! (continued) • when reattaching the mini-latch plate and mini- buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding procedure to detach the mini-latch plate and mini- buckle, untwist the webbing, and reattach the mini- latch plate and mini-buck...

  • Page 192

    Seat belts and pregnant women seat belts must be worn by all occupants including preg- nant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong...

  • Page 193

    Switchable automatic locking retractors (alr) the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) which is used to secure a child restraint system. For additional information, refer to “installing child restraints using the vehicle seat ...

  • Page 194

    In automatic locking mode, the shoulder belt is automati- cally pre-locked. The seat belt will still retract to remove any slack in the shoulder belt. Use the automatic locking mode anytime a child restraint is installed in a seating position that has a seat belt with this feature. Children 12 years...

  • Page 195

    Supplemental restraint systems (srs) some of the safety features described in this section may be standard equipment on some models, or may be optional equipment on others. If you are not sure, ask your autho- rized dealer. The air bag system must be ready to protect you in a collision. The occupant...

  • Page 196

    The orc also includes diagnostics that will illuminate the instrument panel air bag warning light if a malfunction is detected that could affect the air bag system. The diagnos- tics also record the nature of the malfunction. While the air bag system is designed to be maintenance free, if any of the...

  • Page 197

    Warning! • being too close to the steering wheel or instrument panel during front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. (continued) warning! (continued)...

  • Page 198

    This vehicle may be equipped with a driver and/or front passenger seat belt buckle switch that detects whether the driver or front passenger seat belt is buckled. The seat belt buckle switch may adjust the inflation rate of the ad- vanced front air bags. Warning! • no objects should be placed over o...

  • Page 199

    The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The front air bags fully inflate in less time than it takes to blink your eyes. The front air bags then quickly deflate while helping to res...

  • Page 200

    The sabs (if equipped with sabs) may help to reduce the risk of occupant injury during certain side impacts, in addition to the injury reduction potential provided by the seat belts and body structure. When the sab deploys, it opens the seam on the outboard side of the seatback’s trim cover. The inf...

  • Page 201

    Sabics (if equipped with sabics) may help reduce the risk of head and other injuries to front and rear seat outboard occupants in certain side impacts, in addition to the injury reduction potential provided by the seat belts and body structure. The sabic deploys downward, covering the side windows. ...

  • Page 202

    The side air bags will not deploy in all side collisions, including some collisions at certain angles, or some side collisions that do not impact the area of the passenger compartment. The side air bags may deploy during angled or offset frontal collisions where the front air bags deploy. Side air b...

  • Page 203

    Rollover events (if equipped with rollover sensing) side air bags are designed to activate in certain rollover events. The occupant restraint controller (orc) deter- mines whether the deployment of the side air bags in a particular rollover event is appropriate, based on the severity and type of col...

  • Page 204

    Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or all of the following may occur: • the air bag material may sometimes cause abrasions and/or skin reddening ...

  • Page 205

    Enhanced accident response system in the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the orc will determine whether to have the enhanced accident response system perform the following functions: • cut off fuel t...

  • Page 206

    Warning! (continued) dealer. Only manufacturer approved seat accessories may be used. If it is necessary to modify the air bag system for persons with disabilities, contact your authorized dealer. Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose ...

  • Page 207

    Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. Warning! In a collision, an unrestrained child can become a projectile inside the vehicle....

  • Page 208

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child re- straint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrie...

  • Page 209

    Infant and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear- facing: infant carriers and conv...

  • Page 210

    Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and con- vertible child seats used in the forward-facing direction are for children who are over two ye...

  • Page 211

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 212

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 213

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchorage system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch-equipped child seats. There ...

  • Page 214

    Crew cab 60/40 split bench latch positions lower anchorage symbol (2 anchorages per seating position) top tether anchorage symbol crew cab full bench latch positions lower anchorage symbol (2 anchorages per seating position) top tether anchorage symbol 212 safety.

  • Page 215

    Frequently asked questions about installing child restraints with latch what is the weight limit (child’s weight + weight of the child re- straint) for using the latch anchor- age system to attach the child re- straint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the...

  • Page 216

    Frequently asked questions about installing child restraints with latch can two child restraints be attached using a common lower latch an- chorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the se...

  • Page 217

    Locating the latch anchorages — crew cab only the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along ...

  • Page 218

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear- facing child restraint...

  • Page 219

    Center seat latch regular cab or crew cab full bench rear seat: no lower center latch anchorages available warning! • do not install a child restraint in the center position using the latch system. This position is not ap- proved for installing child seats using the latch attachments. You must use t...

  • Page 220

    Forward and rearward in the vehicle, you may wish to move it to its rear-most position to make room for the child seat. You may also move the front seat forward to allow more room for the child seat. 3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the select...

  • Page 221

    Installing child restraints using the vehicle seat belt child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt. Warning! • improper installation or failure to properly secure a child restraint can lead to failure of the restrai...

  • Page 222

    Lap/shoulder belt systems for installing child restraints in this vehicle regular cab automatic locking retractor (alr) locations alr = switchable automatic locking retractor top tether anchorage symbol crew cab automatic locking retractor (alr) locations cinch = cinching latchplate alr = switchable...

  • Page 223

    Frequently asked questions about installing child restraints with seat belts what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tethe...

  • Page 224

    1. For crew cab models place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its rear-m...

  • Page 225

    Installing a child restraint with a cinching latch plate (cinch) — if equipped: child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt. Warning! • improper installation or failure to properly secure a child restraint can lead t...

  • Page 226

    Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. If the buckle or the cinching latch plate is too close to the belt path opening of the child restraint, you may have trouble tightening the seat belt. If this happens, disconnect the latch pla...

  • Page 227

    Regular cab trucks: in the regular cab truck, the top tether anchorages are located behind the center and right passenger seats. There is a plastic cover over each anchorage. To attach the tether strap of the child restraint: 1. Place the child restraint on the seat and adjust the tether strap so th...

  • Page 228

    3. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. Tighten the tether strap according to the child seat manufacturer’s instruc- tions. Warning! Never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can cau...

  • Page 229

    2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint, through the tether strap loop behind the seat and over to the tether strap loop behind the center seat. 3. Pass the tether strap hook under the head restraint behind...

  • Page 230

    4. Attach the hook to the center tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s instructions. Note: if there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connecte...

  • Page 231

    3. Pass the tether strap hook under the head restraint behind the child seat, though the tether strap loop behind the seat and over to the right or left outboard tether strap loop. 4. Attach the hook to the outboard tether strap loop (see diagram). Tighten the tether strap according to the child sea...

  • Page 232

    4. Attach the hook to the outboard tether strap loop. 5. Tighten the tether straps according to the child seat manufacturer’s instructions, tightening the right and left tether straps before the center tether strap. Warning! • an incorrectly anchored tether strap could lead to increased head motion ...

  • Page 233

    Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 234

    Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, dam- aged, deteriorated, ...

  • Page 235

    Warning! An improperly attached, damaged, folded, or stacked floor mat, or damaged floor mat fasteners may cause your floor mat to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control. To prevent serious injury or death: • always securely attach your floor mat ...

  • Page 236

    Warning! (continued) • if the vehicle carpet has been removed and re- installed, always properly attach carpet to the floor and check the floor mat fasteners are secure to the vehicle carpet. Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-ins...

  • Page 237

    Starting and operating contents 䡵 starting the engine — gasoline engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .238 ▫ automatic transmission . . . . . . . . . . . . . . . . . .238 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . . .239 ▫ keyless enter-n-go — ignition ...

  • Page 238

    䡵 speed control . . . . . . . . . . . . . . . . . . . . . . .267 ▫ to activate . . . . . . . . . . . . . . . . . . . . . . . . . . .268 ▫ to set a desired speed. . . . . . . . . . . . . . . . . . .268 ▫ to vary the speed setting . . . . . . . . . . . . . . . .269 ▫ to accelerate for passing . . . . ...

  • Page 239

    ▫ payload. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 ▫ gross axle weight rating (gawr) . . . . . . . . . .289 ▫ tire size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 ▫ rim size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 ▫ inflation pressure . . ....

  • Page 240

    Starting the engine — gasoline engine before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 10-second intervals. Waiting a few seconds between such intervals will protect the starter from ov...

  • Page 241

    Normal starting normal starting of either a warm or cold engine is obtained without pumping or pressing the accelerator pedal. Cycle the ignition to the run position and release when the engine starts. If the engine fails to start within 10 seconds, cycle the ignition to the off position, wait five ...

  • Page 242

    Idle shutdown — 6.4l engine only this feature can be enabled so that the truck will automati- cally shutdown when the truck has been idling for a set period of time when the engine is at operating tempera- ture. Idle time can be set in 5 minute increments between 5 and 60 minutes. See your local aut...

  • Page 243

    If engine fails to start if the engine fails to start after you have followed the “normal starting” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while the engine is cranking. This should clear any excess fuel in case the engine is flooded. The s...

  • Page 244

    Cold weather operation (below –22°f or −30°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. After starting the idle speed is controlled automatically, and it will decrease as the en...

  • Page 245

    Under which vehicle operations will occur. For the recom- mended viscosity and quality grades, refer to “fluids and lubricants” in “technical specifications”. Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil duri...

  • Page 246

    When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. Apply the parking brake before placing the gear selector in park, otherwise the load on the transmission locking mechanism may make it difficult to move the...

  • Page 247

    Automatic transmission warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or...

  • Page 248

    Warning! (continued) • do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition (in a vehicle equipped with keyless enter-n-go) in the acc or on/run mode. A child could operate power windows, other controls, or move the vehicle. Caution...

  • Page 249

    Six–speed automatic transmission — if equipped chassis cab models (with automatic transmission) may use either the as66rc transmission (which is equipped with a power take-off (pto) access cover on the side of the transmission case), or the 66rfe transmission (which has no pto access cover). The tra...

  • Page 250

    Park (p) this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use park while the vehicle is in motion. Apply the parking brake when exiting the vehicle in this range. When parking on a level surface, you may shift the transmi...

  • Page 251

    Warning! (continued) the transmission into park, turn the engine off, and remove the key fob. When the ignition is in the lock/off (key removal) position (or, with keyless enter-n-go, when the ignition is in the off mode), the transmission is locked in park, securing the vehicle against unwanted mov...

  • Page 252

    Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral (n) use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake an...

  • Page 253

    If the transmission temperature exceeds normal operating limits, the powertrain controller will modify the transmis- sion shift schedule and expand the range of torque con- verter clutch engagement. This is done to prevent trans- mission damage due to overheating. If the transmission becomes extreme...

  • Page 254

    Illuminated. Limp home mode allows the vehicle to be driven to an authorized dealer for service without damag- ing the transmission. In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following steps: 1. Stop the vehicle. 2. Shift the tra...

  • Page 255

    To exit ers mode, simply push and hold the ers (+) switch until the gear limit display disappears from the instrument cluster. Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or pers...

  • Page 256

    When to use tow/haul mode when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, push the tow/haul switch to activate tow/haul mode. This will improve performance and reduce the potential for transmission overheating or failure due to e...

  • Page 257

    Note: • the torque converter clutch will not engage (and 66rfe- equipped trucks will not shift to sixth gear), until the transmission fluid and engine coolant are warm [usually after 1 to 3 miles (2 to 5 km) of driving]. Because engine speed is higher when the torque converter clutch is not engaged,...

  • Page 258

    4l four-wheel drive low range — this range locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). This transfer case is intended...

  • Page 259

    Warning! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neu- tral position without first fully engaging the park- ing brake. The transfer case neutral position disen- gages both the front and rear drive shafts from the powertrain and will a...

  • Page 260

    Shifting procedure — manually shifted transfer case 2h to 4h shifting between 2h and 4h can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h). With the vehicle in motion, the transfer case will engage/disengage faster if you momenta...

  • Page 261

    Electronically shifted transfer case (four-position switch) — if equipped the electronic shift transfer case is operated by the 4wd control switch (transfer case switch), which is located on the instrument panel. This electronically shifted transfer case provides four mode positions: • two-wheel dri...

  • Page 262

    Behind another vehicle. Refer to “recreational towing” in this section for further information. Warning! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neu- tral position without first fully engaging the park- ing brake. The transfer case n...

  • Page 263

    If one or more of the following shift conditions are not met: 1. The indicator light for the current position will remain on. 2. The newly selected position indicator light will continue to flash. 3. The transfer case will not shift. Note: before retrying a selection, make certain that all the neces...

  • Page 264

    Shifting procedure note: • if any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The position indicator light for the previous posi- tion will remain on and the newly selected position indicator light will continue to flash until all t...

  • Page 265

    Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped. You can use either of the following procedures: preferred procedure 1. With the engine running, slow the vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into neutral. 3. While still roll...

  • Page 266

    The limited-slip differential is especially helpful during slippery driving conditions. With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction. When starting with only one rear wheel on an excessively slippery surface, slight mo- mentary app...

  • Page 267

    • brake pedal must not be applied. • vehicle engine must be running. • no vehicle, brake or clutch switch faults present. • pto must be correctly installed using the vehicle pro- vided circuits. The instrument cluster will display a ⬙ pto on ⬙ message for five seconds if the above conditions are met...

  • Page 268

    • (on/off) switch has been activated. • vehicles with automatic transmission must be in park or drive. • parking brake must not be applied. • brake pedal must not be applied. • no vehicle, brake or clutch switch faults present. • vehicle engine must be running. • pto must be correctly installed usin...

  • Page 269

    Note: • increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that there is a problem with the power steering system. • upon initial start-up in cold weather, the power steering pump may make noise for a short amount of time. This is due to the cold...

  • Page 270

    The speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the speed control system can be reactiv...

  • Page 271

    To vary the speed setting to increase speed when the speed control is set, you can increase speed by pushing the res (+) button. The driver’s preferred units can be selected through the instrument panel settings if equipped. Refer to “getting to know your instrument panel” for more information. The ...

  • Page 272

    To accelerate for passing press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the speed control system maintains speed up and d...

  • Page 273

    Parksense can be active only when the gear selector is in reverse. If parksense is enabled at this gear selector position, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above. When in reverse and above the system’s operat- ing speed, a warning...

  • Page 274

    If an object is detected in the left and/or right rear region, the display will show a single solid arc in the left and/or right rear region and the system will produce a tone. As the vehicle moves closer to the object, the display will show the single arc moving closer to the vehicle and the tone w...

  • Page 275

    Fast tone continuous tone 6 starting and operating 273.

  • Page 276

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: warning alerts rear distance (inches/cm) greater than 79 inches (200 cm) 79-45 inches (...

  • Page 277

    Adjustable chime volume settings the rear chime volume settings are programmable. • the settings may be programmed through the uconnect system. Refer to “uconnect settings ” in “multimedia” for further information. Enabling and disabling parksense parksense can be enabled and disabled with the parks...

  • Page 278

    If ⬙ parksense unavailable wipe rear sensors ⬙ appears in the instrument cluster display make sure the outer surface and the underside of the rear fascia/bumper is clean and clear of snow, ice, mud, dirt or other obstruc- tion, and then cycle the ignition. If the message continues to appear, see you...

  • Page 279

    Causing the ⬙ parksense unavailable service required ⬙ message to appear in the instrument cluster display. • on vehicles equipped with a tailgate, parksense should be disabled when the tailgate is in the lowered or open position and the vehicle is in reverse. A lowered tailgate could provide a fals...

  • Page 280

    Parksense front and rear park assist — if equipped the parksense park assist system provides visual and audible indications of the distance between the rear and/or front fascia and a detected obstacle when backing up or moving forward, e.G. During a parking maneuver. Refer to “parksense system usage...

  • Page 281

    Parksense warning display the parksense warning screen is located within the instru- ment cluster display. It provides visual warnings to indi- cate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle. Refer to “instrument cluster display” in “getting to ...

  • Page 282

    The vehicle is close to the obstacle when the display shows one flashing arc and sounds a continuous tone. The follow- ing chart shows the warning alert operation when the system is detecting an obstacle: warning alerts rear distance (inches/cm) greater than 79 inches (200 cm) 79-45 inches (200-115 ...

  • Page 283

    Front park assist audible alerts parksense will turn off the front park assist audible alert (chime) after approximately three seconds when an ob- stacle has been detected, the vehicle is stationary, and brake pedal is applied. Adjustable chime volume settings the front and rear chime volume setting...

  • Page 284

    Service the parksense park assist system during vehicle start up, when the parksense system has detected a faulted condition, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the ⬙ parksense unavailable wipe rear sensors ⬙ , ⬙ parksense unavailable wip...

  • Page 285

    Parksense system usage precautions note: • ensure that the front and rear bumper are free of snow, ice, mud, dirt and debris to keep the parksense system operating properly. • jackhammers, large trucks, and other vibrations could affect the performance of parksense. • when you turn front or rear par...

  • Page 286

    Warning! • drivers must be careful when backing up even when using parksense. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are respon- sible for safety and must continu...

  • Page 287

    Uconnect screen (if equipped) along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear. Note: for the 3500, 4500 and 5500 chassis cab vehicles, the rear backup camera is shipped loose and not installed. Please refer to the ram...

  • Page 288

    When enabled, active guide lines are overlaid on the image to illustrate the width of the vehicle and its projected backup path based on the steering wheel position. The active guide lines will show separate zones that will help indicate the distance to the rear of the vehicle. Note: for further inf...

  • Page 289

    Turning rear view camera image on: 1. Press the ⬙ controls ⬙ button located on the bottom of the uconnect display. 2. Press the ⬙ backup camera ⬙ button to turn the rear view camera system on. Note: once initiated by the ⬙ backup camera ⬙ button, the rear view camera image may be deactivated by pres...

  • Page 290

    Warning! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperl...

  • Page 291

    Payload the payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo. Gross axle weight rating (gawr) the gawr is the maximum permissible load on the front and rear axles. The load must be distributed in the...

  • Page 292

    Weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving. Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Caution! ...

  • Page 293

    Warning! If the gross trailer weight is 5,000 lbs (2,267 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle. If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision. Gross combination weight ra...

  • Page 294

    Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kinds of hitches are the most popular on the market today and they are commonly used to tow small and medium sized...

  • Page 295

    Recommended distribution hitch adjustment towing with 1500 air suspension 1. Set air suspension to normal ride height. No action is required if already in normal ride height. Note: the vehicle must remain in the engine run position with all doors closed while attaching a trailer for proper leveling ...

  • Page 296

    3. Under the instrument cluster or touch screen radio settings, enable jack mode. Jack mode will be canceled and procedure must be restarted if the vehicle is driven at speeds above 5mph (8 kmh). 4. Measure the height of the top of the front wheel opening on the fender to ground, this is height h1. ...

  • Page 297

    Towing with 2500/3500 air suspension 1. Position the truck to be ready to connect to the trailer (do not connect the trailer). Note: normal ride height (nrh) or alternate trailer height (ath) can be used. The vehicle must remain in the engine running position while attaching a trailer for proper lev...

  • Page 298

    4. Measure the height of the top of the front wheel opening on the fender to ground, this is height h2. 5. Install and adjust the tension in the weight distributing bars per the manufacturers’ recommendations so that the height of the front fender is approximately (h2-h1)/ 2+h1 (about 1/2 the differ...

  • Page 299

    Trailer hitch type and maximum trailer weight hitch type max. Trailer weight / max. Tongue weight class iii bumper hitch - 1500 model 5,000 lbs (2,268 kg) / 500 lbs (226 kg) class iv - 1500 model 11,000 lbs (4,989 kg) / 1100 lbs (498 kg) class v - 2500/3500 models 18,000 lbs (8,164 kg) / 1800 lbs (8...

  • Page 300

    Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weight of the driver and all passengers. Note: remember that everything put into or on the...

  • Page 301

    Warning! (continued) • when hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, sus- pension, chassis structure or tires. • safety chains must always be used b...

  • Page 302

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible per- sonal injury. • an electronically actuated trailer brake controller is required when towing a trailer...

  • Page 303

    The user interface consists of the following: manual brake control lever slide the manual brake control lever to the left to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes. If the manual brake control lever is activated while the brake is also applied, the gr...

  • Page 304

    Gain the gain setting is used to set the trailer brake control for the specific towing condition and should be changed as towing conditions change. Changes to towing conditions include trailer load, vehicle load, road conditions and weather. Adjusting gain note: this should only be performed in a tr...

  • Page 305

    Light electric heavy electric light eoh heavy eoh type of trailer brakes electric trailer brakes electric trailer brakes electric over hydrau- lic trailer brakes electric over hydrau- lic trailer brakes load *under 10,000 lbs *above 10,000 lbs *under 10,000 lbs *above 10,000 lbs * the suggested sele...

  • Page 306

    Towing requirements — trailer lights and wiring whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The trailer tow package may include a four- and seven-pin wiring harness. Use a factory approved trailer harness a...

  • Page 307

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic transmission the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. ...

  • Page 308

    Note: check the automatic transmission fluid level be- fore towing. Tow/haul mode to reduce potential for automatic transmission overheat- ing, activate tow/haul mode when driving in hilly areas, or select a lower gear range (using the electronic range select (ers) shift control) on more severe grad...

  • Page 309

    Note: before installation of a snowplow it is highly recommended that the owner/installer obtain and follow the recommendations contained within the current body builders guide. See your authorized dealer, installer or snowplow manufacturer for this information. There are unique electrical systems t...

  • Page 310

    Vehicle front end wheel alignment was set to specifications at the factory without consideration for the weight of the plow. Front end toe-in should be checked and reset if necessary at the beginning and end of the snowplow season. This will help prevent uneven tire wear. The blade should be lowered...

  • Page 311

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models flat tow none not al- lowed see instructions • automatic transmission in park • manual transmission in gear (not in neu- tral)...

  • Page 312

    Recreational towing — two-wheel drive models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is al- lowed only if the rear wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dol...

  • Page 313

    Caution! (continued) damage. Tow with all four wheels either on the ground, or off the ground (using a vehicle trailer). • tow only in the forward direction. Towing this vehicle backwards can cause severe damage to the transfer case. • before recreational towing, the transfer case must be in neutral...

  • Page 314

    1. Bring the vehicle to a complete stop on level ground, with the engine running. Firmly apply the parking brake. 2. Shift the transmission to neutral. 3. Press and hold the brake pedal. 4. Depress the clutch pedal on a manual transmission. 5. Shift the transfer case into neutral: • with manual shif...

  • Page 315

    Any of these requirements are not met before pushing the neutral (n) button or are no longer met during the shift, the neutral (n) indicator light will flash continuously until all requirements are met or until the neutral (n) button is released. • the ignition must be in the on/run mode for a shift...

  • Page 316

    9. Start the engine. 10. Press and hold the brake pedal. 11. Release the parking brake. 12. Shift the transmission into gear, release the brake pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally. Note: with electronic shift transfer case: • steps 3 and 4 a...

  • Page 317

    Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Further- more, flowing and/or rising water can carry your ve- hi...

  • Page 318

    Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • determine the condition of the road or the path that is under water and if there are any obstacles in the wa...

  • Page 319

    In case of emergency contents 䡵 hazard warning flashers . . . . . . . . . . . .318 䡵 assist and sos mirror — if equipped . . . .318 䡵 bulb replacement . . . . . . . . . . . . . . . . . . . .323 ▫ replacement bulbs . . . . . . . . . . . . . . . . . . . . .323 ▫ replacing exterior bulbs . . . . . . . ...

  • Page 320

    Hazard warning flashers the hazard warning flasher switch is located on the upper switch bank just below the radio. Push the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Push t...

  • Page 321

    Warning! Always obey traffic laws and pay attention to the road. Always drive safely with your hands on the steering wheel. You have full responsibility and as- sume all risks related to the use of the uconnect and siriusxm guardian features and applications in this vehicle. Only use uconnect featur...

  • Page 322

    2. The led light located between the assist and sos buttons on the rearview mirror will turn green once a connection to a sos operator has been made. 3. Once a connection between the vehicle and a sos operator is made, the sos call system may transmit the following important vehicle information to a...

  • Page 323

    Warning! • if anyone in the vehicle could be in danger (e.G., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an emergency services agent. All occupants should exit the vehicle immediately and move to a safe location. • never place anything on or ...

  • Page 324

    • an in-vehicle audio message will state “vehicle device requires service. Please contact your dealer.” warning! • ignoring the rearview mirror light could mean you will not have sos call services. If the rearview mirror light is illuminated, have an authorized dealer service the sos call system imm...

  • Page 325

    Note: • your vehicle may be transmitting data as authorized by the subscriber. • never place anything on or near the vehicle’s lte (voice/data) or 4g (data) and gps antennas. You could prevent lte (voice/data) or 4g (data) and gps signal reception, which can prevent your vehicle from placing an emer...

  • Page 326

    Light bulbs — exterior bulb number quad headlamp – low beam h11 quad headlamp – high beam 9005 quad headlamp – front turn signal lamp 3157na premium headlamp – low beam hir2 premium headlamp – high beam 9005 premium headlamp – front turn signal lamp led (see authorized dealer for service) horizontal...

  • Page 327

    7. Reach into the front wheel house ahead of the front wheel, remove the fastener, and lift the cover over the access hole in the front of the wheel house splash shield. Access to the rear of the lamp can be gained through this access hole. 8. Reach through the access hole of the wheel house splash ...

  • Page 328

    Caution! • do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • always use the correct bulb size and type for replace- ment. An incorrect bulb size or type may overheat and cause damage to the lamp, th...

  • Page 329

    2. Separate the connector holding the housing and wiring harness to the body. 3. Turn the desired bulb socket ¼ turn and remove the socket and bulb from housing. 4. Pull the desired bulb straight from the socket. Caution! Do not contaminate the bulb glass by touching it with your fingers or by allow...

  • Page 330

    Cab top clearance lamps — if equipped 1. Remove the two screws from the top of the lamp. 2. Rotate the bulb socket ¼ turn and pull it from the lamp assembly. Removing rear screw from clearance lamp removing bulb socket from clearance lamp 328 in case of emergency.

  • Page 331

    3. Pull the bulb straight from it’s socket and replace. Fuses warning! • when replacing a blown fuse, always use an appro- priate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires o...

  • Page 332

    Power distribution center the power distribution center is located in the engine compartment near the battery. This center contains car- tridge fuses, micro fuses, relays, and circuit breakers. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number o...

  • Page 333

    Cavity cartridge fuse micro fuse description f08 20 amp blue (1500 ld/cummins die- sel) – emissions diesel – if equipped f09 40 amp green (spe- cial services vehicle & cummins diesel) – diesel fuel heater – if equipped f10 40 amp green – body controller / exterior lighting #2 f10 50 amp red – body c...

  • Page 334

    Cavity cartridge fuse micro fuse description f22 20 amp blue 30 amp pink (cum- mins diesel) – engine control module f23 30 amp pink – body controller #1 / interior lighting f24 30 amp pink – driver door module f25 30 amp pink – front wiper f26 30 amp pink – antilock brakes / stability control module...

  • Page 335

    Cavity cartridge fuse micro fuse description f38 30 amp pink – power inverter 115v ac – if equipped f39 20 amp blue – power outlet – special services only f41 – 10 amp red active grill shutter – if equipped f42 – 20 amp yellow horn f44 – 10 amp red diagnostic port f46 – 10 amp red upfitter – if equi...

  • Page 336

    Cavity cartridge fuse micro fuse description f60 – 15 amp blue underhood lamp f61 – 10 amp red (1500 ld diesel & cum- mins diesel) pm sensor – if equipped f62 – 10 amp red air conditioning clutch f63 – 20 amp yellow ignition coils (gas), urea heater (cummins diesel) f64 – 25 amp clear fuel injectors...

  • Page 337

    Cavity cartridge fuse micro fuse description f74 – 20 amp yellow (gas engine & 1500 ld diesel) brake vacuum pump gas/diesel – if equipped f75 – 10 amp red coolant temperature valve actuator f76 – 10 amp red antilock brakes / electronic stability control f77 – 10 amp red drivetrain control module/fro...

  • Page 338

    Cavity cartridge fuse micro fuse description f90/f91 – 20 amp yellow power outlet (rear seats) customer select- able f93 – 20 amp yellow cigar lighter f94 – 10 amp red shifter / transfer case module f95 – 10 amp red rear camera / park assist f96 – 10 amp red rear seat heater switch f97 – 25 amp clea...

  • Page 339

    Caution! • when installing the power distribution center cover, it is important to ensure the cover is properly posi- tioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • when replacing a blown fus...

  • Page 340

    Preparations for jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Place the...

  • Page 341

    Warning! (continued) • if working on or near a roadway, be extremely careful of motor traffic. • to assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. Caution! Do not attempt to raise the vehicle by jacking on locations other ...

  • Page 342

    When changing a rear wheel, assemble the jack driver to the jack and connect the jack driver to the extension tubes. Securely place the jack under the sway bar bracket (unless both tires are flat on one side, then place jack under shock bracket) facing forward in vehicle. Connect the extension tubes...

  • Page 343

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the lug nuts and pull the wheel off. Install the spare wheel and lug nuts with the cone shaped end of ...

  • Page 344

    Dual wheel models require a special heavy-duty lug nut tightening adapter (included with the vehicle) to correctly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device. Note: when installing a spare tire (if equipped) as part of...

  • Page 345

    Hook at one end that will fit in the pull off notch of the rear hub caps. Position the hook and pull straight out on the ratchet firmly. The hub cap should pop off. The wheel skins can now be removed. For the front hub cap, use the flat blade on the end of the lug wrench to pull the caps off. The wh...

  • Page 346

    Preparations for jump start the battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. Note: the positive battery post may be covered with a protective cap if equipped. Lift up on the cap to gain access to the positive battery post. Do not jump...

  • Page 347

    Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump starting procedure warning! Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion. Caution! Failu...

  • Page 348

    Caution! Do not connect jumper cable to any of the fuses on the positive battery terminal. The resulting electrical cur- rent will blow the fuse. 6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the...

  • Page 349

    • you can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. Warning! You or others can be badly burned by hot engine...

  • Page 350

    6. Move the gear selector to the neutral position. 7. The vehicle may then be started in neutral. Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand, or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheel...

  • Page 351

    Warning! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously witho...

  • Page 352

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. If the transmis- sion and drivetrain are operable, disabled vehicles may also be towed as described under “recreational towing” in the “starting and operating” section. Towing...

  • Page 353

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is man- datory. Attach a tow bar or other towing device to main structural members ...

  • Page 354

    Caution! Towing this vehicle in violation of the above require- ments can cause severe engine and/or transmission damage. Damage from improper towing is not covered under the new vehicle limited warranty. Four-wheel drive models the manufacturer recommends towing with all wheels off the ground. Acce...

  • Page 355

    Caution! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. Enhanced accident response system (ears) this vehicle is equipped with an enhanced accident response system. Please refer ...

  • Page 357

    Servicing and maintenance contents 䡵 scheduled servicing . . . . . . . . . . . . . . . . .357 ▫ maintenance plan . . . . . . . . . . . . . . . . . . . . . .358 ▫ heavy duty use of the vehicle . . . . . . . . . . . .361 䡵 engine compartment . . . . . . . . . . . . . . . . .362 ▫ 6.4l engine . . . . ....

  • Page 358

    䡵 tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .392 ▫ tire safety information . . . . . . . . . . . . . . . . . .392 ▫ tires — general information . . . . . . . . . . . . . .401 ▫ tire types . . . . . . . . . . . . . . . . . . . . . . . . . . . .407 ▫ spare tires — if equipped...

  • Page 359

    Scheduled servicing your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This ...

  • Page 360

    Maintenance plan required maintenance refer to the maintenance plan on the following pages for required maintenance. At every oil change interval as indicated by oil change indicator system: • change oil and filter. • rotate the tires. Rotate at the first sign of irregular wear, even if it occurs be...

  • Page 361

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 362

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 363

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 364

    Engine compartment 6.4l engine 1 — coolant pressure bottle 6 — battery 2 — transmission dipstick 7 — power distribution center (fuses) 3 — engine oil fill 8 — washer solvent 4 — engine oil dipstick 9 — power steering fluid reservoir 5 — brake fluid reservoir 10 — air cleaner filter 362 servicing and...

  • Page 365

    Checking oil level — gas engine to assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed up ...

  • Page 366

    Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Ref...

  • Page 367

    Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. Engine oil — gas engine change engine ...

  • Page 368

    Engine oil viscosity (sae grade) — 6.4l engine use mopar sae 0w-40 engine oil approved to fca mate- rial standard ms-12633 such as pennzoil ultra equivalent is recommended for all operating temperatures. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For i...

  • Page 369

    Note: be sure to follow the “severe duty conditions” maintenance interval if applicable. Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such remo...

  • Page 370

    2. Lift the air cleaner cover to access the air cleaner filter. 3. Remove the air cleaner filter element from the housing assembly. Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air clea...

  • Page 371

    2. Install the air cleaner cover onto the housing assembly locating tabs. 3. Latch the spring clips and lock the air cleaner cover to the housing assembly. Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the st...

  • Page 372

    Refrigerant recovery and recycling — r–1234yf r–1234yf air conditioning refrigerant is a hydrofluo- roolefin (hfo) that is endorsed by the environmental protection agency and is an ozone-friendly substance with a low global-warming potential. The manufacturer recom- mends that air conditioning servi...

  • Page 373

    3. There are glove compartment travel stops on both sides of the glove compartment door, push inward on both sides of the glove compartment to release the glove compartment travel stops. 4. Disengage the glove compartment door from its hinges by opening the glove compartment past the travel stop and...

  • Page 374

    Finger tabs finger tab 372 servicing and maintenance.

  • Page 375

    6. Remove the cabin air filter by pulling it straight out of the housing. 7. Install the cabin air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, press on each end until you hear an audible click. Caution! The cabin air filter is identified with an a...

  • Page 376

    Note: ensure the glove compartment door hinges and glove compartment travel stops are fully engaged. 10. Reattach the glove compartment tension tether by inserting the tether clip in the glove compartment and sliding the clip away from the face of the glove compartment door. Front driveshaft lubrica...

  • Page 377

    The grease fitting is located at the rear of the front driveshaft, near the centering mechanism of double cardan joint. Refer to the “maintenance plan” for the proper maintenance intervals. Use mopar type ms-6560 (lithium- based grease), or equivalent. Accessory drive belt inspection warning! • do n...

  • Page 378

    Conditions that would require replacement: • rib chunking (one or more ribs has separated from belt body) • rib or belt wear • longitudinal belt cracking (cracks between two ribs) • belt slips • “groove jumping ⬙ (belt does not maintain correct posi- tion on pulley) • belt broken (note: identify and...

  • Page 379

    The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant, such as mopar lock cylinder lubricant directly into the lock cylinder. Windshield wiper blades clean the rubber edges of the wiper blades and the windsh...

  • Page 380

    1. Lift the wiper arm to raise the wiper blade off of the glass, until the wiper arm is in the full up position. 2. To disengage the wiper blade from the wiper arm, flip up the locking tab. Windshield wiper arm 1 — wiper 2 — locking tab 3 — wiper arm wiper locking assembly 1 — wiper 2 — locking tab ...

  • Page 381

    3. Tilt the lower end of the wiper blade away from the arm and use one finger push the release tab toward the wiper arm. 4. Slide the wiper blade down towards the base of the wiper arm. 5. With the wiper blade disengaged, remove the wiper blade from the wiper arm by holding the wiper arm with one ha...

  • Page 382

    Installing the front wipers 1. Lift the wiper arm off of the glass, until the wiper arm is in the full up position. 2. Position the wiper blade under the hook on the tip of the wiper arm with the wiper locking tab open. 3. Insert the receiver bracket on the wiper assembly into the hook on the tip of...

  • Page 383

    Caution! • the catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- ness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • damage to the catalytic converter can resul...

  • Page 384

    Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiat...

  • Page 385

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine dam- age and may decrease corrosion protection. Organic additive technology (oat) engine coolant is differ- ent and should not be mixed with hyb...

  • Page 386

    • use only high purity water such as distilled or deionized water when mixing the water/engine coolant (anti- freeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Note: • it is the owner’s responsibility to maintain the proper ...

  • Page 387

    Disposal of used coolant used ethylene glycol-based coolant (antifreeze) is a regu- lated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol-based coolant...

  • Page 388

    • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms.90032) and distilled water for proper corrosion pro- tection of your engine which contains aluminum com- ponents. • make sure that the coolant expansion bottle overflow hoses are not kinked or obst...

  • Page 389

    Refer to “fluids and lubricants” in “technical specifica- tions” for further information. Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids and lubricants” in “technical specifications” for further information. Using the wrong type of brake fluid can severely damage your b...

  • Page 390

    Caution! Using a transmission fluid other than the manufactur- er’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder, and will require more frequent fluid and filter changes. Refer to “fluids and lubricants” in “technical specifications” for flu...

  • Page 391

    2. Park the vehicle on level ground. 3. Run the engine at normal idle speed for at least 60 seconds, and leave the engine running for the rest of this procedure. 4. Fully apply the parking brake and press the brake pedal. 5. Place the gear selector momentarily into each gear position (allowing time ...

  • Page 392

    9. Reinsert the dipstick. Check for leaks. Release the park- ing brake. Note: to prevent dirt and water from entering the trans- mission after checking or replenishing fluid, make sure that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its full...

  • Page 393

    Refer to “scheduled servicing” in this chapter for the proper maintenance intervals. Lubricant selection refer to “fluids and lubricants” in “technical specifica- tions” for further information. Note: the presence of water in the gear lubricant will result in corrosion and possible failure of differ...

  • Page 394

    Tires tire safety information tire safety information will cover aspects of the following information: tire markings, tire identification numbers, tire terminology and definitions, tire pressures, and tire loading. Tire markings tire markings 1 — u.S. Dot safety standards code (tin) 4 — maximum load...

  • Page 395

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 396

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ ....Blank.... ⴖ = passenger car tire based on european design standards, or lt = light truck tire based...

  • Page 397

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions – the maximum speed corr...

  • Page 398

    Tire identification number (tin) the tin may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 399

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located be- hind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hour...

  • Page 400

    Tire loading and tire pressure note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure...

  • Page 401

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 402

    Steps for determining correct load limit— (1) locate the statement “the combined weight of occupants and cargo should never exceed xxx kg or xxx lbs.” on your vehicle’s placard. (2) determine the combined weight of the driver and passengers that will be riding in your vehicle. (3) subtract the combi...

  • Page 403

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them. Tires — general information tire pressure proper tire inflation pre...

  • Page 404

    • economy • tread wear • ride comfort safety warning! • improperly inflated tires are dangerous and can cause collisions. • underinflation increases tire flexing and can result in overheating and tire failure. • overinflation reduces a tire’s ability to cushion shock. Objects on the road and chuckho...

  • Page 405

    Tire inflation pressures the proper cold tire inflation pressure is listed on the driver’s side b-pillar or rear edge of the driver’s side door. At least once a month: • check and adjust tire pressure with a good quality pocket- type pressure gauge. Do not make a visual judgement when determining pr...

  • Page 406

    Dealer for recommended safe operating speeds, loading and cold tire inflation pressures. Warning! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious collision. Do not drive a vehicle loaded to the ma...

  • Page 407

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping. Refer to “freeing a stuck vehicle” in “in case of emer- gency” for further information. Warning! Fast spinning tires c...

  • Page 408

    Life of tire the service life of a tire is dependent upon varying factors including, but not limited to: • driving style. • tire pressure - improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life, res...

  • Page 409

    It is recommended you contact your authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. Warning! • do not use a tire, ...

  • Page 410

    Summer or three season tires — if equipped summer tires provide traction in both wet and dry condi- tions, and are not intended to be driven in snow or on ice. If your vehicle is equipped with summer tires, be aware these tires are not designed for winter or cold driving conditions. Install winter t...

  • Page 411

    Spare tires — if equipped note: for vehicles equipped with tire service kit instead of a spare tire, please refer to “tire service kit” in “in case of emergency” for further information. Caution! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a c...

  • Page 412

    Warning! (continued) needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control. Collapsible spare tire — if equipped the collapsible spare is for temporary emergency use only. You can identify if y...

  • Page 413

    Limited use spare — if equipped the limited use spare tire is for temporary emergency use only. This tire is identified by a label located on the limited use spare wheel. This label contains the driving limitations for this spare. This tire may look like the original equipped tire on the front or re...

  • Page 414

    When cleaning extremely dirty wheels including excessive brake dust, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent dam- age to the wheels. Mopar wheel treatment or mopar chrome cleaner or their equivalent is recommended or select a non-abrasive, no...

  • Page 415

    Please follow the table below for proper tire size, chain type, and axle recommendations: vehicle axle recommendations tire sizes chain class chassis cab 3500 (single rear wheel) models rear only lt275/70r18e u class chassis cab 3500 (dual rear wheel) 4x2 models rear only lt235/80r17e u class chassi...

  • Page 416

    Caution! (continued) • install device as tightly as possible and then re- tighten after driving about ½ mile (0.8 km). • do not exceed 30 mph (48 km/h). • drive cautiously and avoid severe turns and large bumps, especially with a loaded vehicle. • do not drive for a prolonged period on dry pave- men...

  • Page 417

    Dual rear wheels the tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. Note: if your vehicle is equipped with a tire pressure in...

  • Page 418

    Caution! (continued) replace an outer rear tire it will have to be remounted on the rim so that the wheel is dished inward. That way the tread design of asymmetrical tires will maintain proper position. Department of transportation uniform tire quality grades the following tire grading categories we...

  • Page 419

    Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade c corresponds to a level of performance, which all pas- senger vehicle tires must meet under the federal motor vehicle safety standar...

  • Page 420

    The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. • atmospheric fallout/industrial pollutants. Body and underbody maintenance cleaning headlights your vehicle is equipped with p...

  • Page 421

    Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • if you detect any stone chips or scratches...

  • Page 422

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them. ...

  • Page 423

    Leather parts mopar total clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cl...

  • Page 425

    Technical specifications contents 䡵 identification data. . . . . . . . . . . . . . . . . . .424 ▫ vehicle identification number . . . . . . . . . . . . .424 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . . .424 ▫ hydraulic brake assist . . . . . . . . . . . . . . . . . . .425 䡵 wheel and...

  • Page 426

    Identification data vehicle identification number the vehicle identification number (vin) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the vehicle frame and underbody as well as the automobile informa- tion disclosure label af...

  • Page 427

    Hydraulic brake assist the brake system power assist is provided by a hydro- boost unit which shares fluid with the power steering system. You may experience some clicking or hissing noises from the hydro-boost system during hard braking conditions. Note: under cold temperatures, pedal effort will b...

  • Page 428

    Note: dual wheels are flat mounted, center piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer. Ensure that the socket is fully engaged on the lug nut/bolt (do not ...

  • Page 429

    Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved. Retighten to specifications after 25 miles (40 km) and check the lug nut/bolt torque to be sure that all the lug nuts/bolts are pr...

  • Page 430

    Fuel requirements 6.4l engine do not use e-85 flex fuel or ethanol blends greater than 15% in this engine. This engines is designed to meet all emissions regulations and provide satis- factory fuel economy and performance when using high quality unleaded gaso- line having a posted octane number rang...

  • Page 431

    Designated top tier detergent gaso- line contains a higher level of detergents to further aide in minimizing engine and fuel system deposits. When avail- able, the usage of top tier detergent gasoline is recommended. Visit www.Toptiergas.Com for a list of top tier detergent gasoline retailers. Indis...

  • Page 432

    Cng and lp fuel system modifications modifications that allow the engine to run on compressed natural gas (cng) or liquid propane (lp) may result in damage to the engine, emissions, and fuel system compo- nents. Problems that result from running cng or lp are not the responsibility of the manufactur...

  • Page 433

    Note: intentional tampering with the emissions control system can result in civil penalties being assessed against you. Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon mon- oxide poisoning: • do not inhale exhaust gase...

  • Page 434

    Fluid capacities u.S. Metric fuel (approximate) standard rear tank 52 gallons 197 liters optional midship tank 22 gallons 83 liters engine oil with filter 6.4l engine (we recommend you use sae 0w-40, synthetic api certi- fied) 7 quarts 6.6 liters cooling system 6.4l engine (we recommend you use mopa...

  • Page 435

    Fluids and lubricants engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar antifreeze/coolant 10– year/150,000 mile formula oat (organic additive tech- nology). Engine oil – 6.4l engine for best performance and maximum protection under all types of operating c...

  • Page 436

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine dam- age and may decrease corrosion protection. Organic additive technology (oat) engine coolant is differ- ent and should not be mixed with hyb...

  • Page 437

    Chassis component fluid, lubricant, or genuine part automatic transmission (6.4l engine with 66rfe trans- mission) (for diesel engine see diesel supplement) use only atf+4 automatic transmission fluid. Failure to use atf+4 fluid may affect the function or performance of your transmission. We recomme...

  • Page 439

    Multimedia contents 䡵 uconnect radios . . . . . . . . . . . . . . . . . . . .439 䡵 personalized menu bar . . . . . . . . . . . . . . .439 䡵 cybersecurity . . . . . . . . . . . . . . . . . . . . . . . .440 䡵 uconnect settings . . . . . . . . . . . . . . . . . . .441 ▫ customer programmable features —...

  • Page 440

    ▫ android auto — if equipped . . . . . . . . . . . . . .499 ▫ general information . . . . . . . . . . . . . . . . . . . . .500 ▫ additional information . . . . . . . . . . . . . . . . . . .500 䡵 cd/dvd disc maintenance . . . . . . . . . . . .501 438 multimedia.

  • Page 441

    Uconnect radios for detailed information about your uconnect radio, refer to your uconnect owner’s manual supplement. Note: uconnect screen images are for illustration pur- poses only and may not reflect exact software for your vehicle. Personalized menu bar the uconnect features and services in the...

  • Page 442

    Cybersecurity your vehicle may be a connected vehicle and may be equipped with both wired and wireless networks. These networks allow your vehicle to send and receive informa- tion. This information allows systems and features in your vehicle to function properly. Your vehicle may be equipped with c...

  • Page 443

    Note: • fca us llc or your dealer may contact you directly regarding software updates. • to help further improve vehicle security and minimize the potential risk of a security breach, vehicle owners should: • routinely check www.Driveuconnect.Com/software- update to learn about available uconnect so...

  • Page 444

    Customer programmable features — uconnect 3 personal settings push the more or settings button on the faceplate, then press the “settings” button on the touchscreen (if equipped) to display the settings menu screen. In this mode the uconnect system allows you to access program- mable features that m...

  • Page 445

    Setting name selectable options display mode auto manual set language english, français, español note: if arabic is selected as the vehicle language, the voice recognition and text messaging features will not function. Touchscreen beep on off fuel saver display on off note: the “fuel saver display” ...

  • Page 446

    Voice after pressing the “voice” button on the touchscreen, the following settings will be available: setting name selectable options voice response length brief detailed show command list always with help never clock & date after pressing the “clock & date” button on the touch- screen, the followin...

  • Page 447

    Safety/assistance after pressing the “safety/assistance” button on the touchscreen, the following settings will be available: setting name selectable options parksense — if equipped sound only sounds and display note: the parksense system will scan for objects behind the vehicle when the transmissio...

  • Page 448

    Setting name selectable options parkview backup camera active guidelines note: your vehicle may be equipped with the parkview rear back up camera active guidelines that allows you to see ac- tive guidelines over the parkview back up camera display whenever the gear selector is put into reverse. The ...

  • Page 449

    Setting name selectable options hill start assist — if equipped note: when the “hill start assist” feature is selected, the hill start assist (hsa) system becomes active. Lights after pressing the “lights” button on the touchscreen, the following settings will be available: setting name selectable o...

  • Page 450

    Setting name selectable options headlights with wipers — if equipped on off auto dim high beams — if equipped on off flash lights with lock on off note: when the “flash lights with lock” feature is selected, the exterior lights will flash when the doors are locked or un- locked with the key fob. Thi...

  • Page 451

    Doors & locks after pressing the “doors & locks” button on the touch- screen, the following settings will be available: setting name selectable options auto door locks on off note: when the “auto door locks” feature is selected, all doors will lock automatically when the vehicle reaches a speed of 1...

  • Page 452

    Setting name selectable options memory linked to fob — if equipped on off note: • the “memory linked to fob” feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. • the seat will return to the memorized seat location if “memory linked to...

  • Page 453

    Auto comfort systems — if equipped after pressing the “auto-on comfort” button on the touchscreen, the following settings will be available: setting name selectable options auto-on driver heated/ventilated seat & steering wheel with vehicle start — if equipped on off note: when the “auto-on driver h...

  • Page 454

    Suspension — if equipped after pressing the “suspension” button on the touchscreen, the following settings will be available: setting name selectable options sound horn with lower on off flash lights with lower on off auto entry/exit suspension on off note: when the “auto entry/exit suspension” feat...

  • Page 455

    Setting name selectable options transport mode on off note: when the “transport mode” feature is selected, the air suspension system is disabled to assist with flat bed towing. Wheel alignment mode note: the “wheel alignment mode” feature prevents auto leveling of the air suspension while performing...

  • Page 456

    Audio after pressing the “audio” button on the touchscreen, the following settings will be available: setting name selectable options balance/fade speaker icon (arrow buttons) c note: the “balance/fade” feature allows you to adjust the balance and fade settings. Press and drag the speaker icon or us...

  • Page 457

    Setting name selectable options aux volume offset — if equipped on off note: the “aux volume offset” feature provides the ability to tune the audio level for portable devices connected through the aux input. Loudness — if equipped on off note: the “loudness” feature improves sound quality at lower v...

  • Page 458

    Compass settings — if equipped after pressing the “compass settings” button on the touchscreen, the following settings will be available: setting name selectable options variance 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 note: • compass variance is the difference between magnetic north and geographic nort...

  • Page 459

    Setting name selectable options perform compass calibra- tion on off note: press the “calibration” button on the touchscreen to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass. When the vehicle is new, the compass may appear erratic unti...

  • Page 460

    Phone/bluetooth after pressing the “phone/bluetooth” button on the touch- screen, the following settings will be available: setting name selectable options paired phones list of paired phones note: the “paired phones” feature shows which phones are paired to the phone/bluetooth system. For further i...

  • Page 461

    Setting name selectable options subscription info sirius id note: new vehicle purchasers or lessees will receive a free limited time subscription to siriusxm satellite radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the subscrip...

  • Page 462

    Clear personal data after pressing the “clear personal data settings” button on the touchscreen, the following settings will be available: setting name selectable options clear personal data yes cancel note: when this feature is selected it will remove all personal data including bluetooth devices a...

  • Page 463

    Customer programmable features — uconnect 4c/4c nav personal settings press the “apps” button on the touchscreen then press the “settings” button on the touchscreen to display the settings menu screen. In this mode the uconnect system allows you to access programmable features that may be equipped s...

  • Page 464

    Display after pressing the “display” button on the touchscreen, the following settings will be available: setting name selectable options display mode day night auto note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the di...

  • Page 465

    Setting name selectable options set theme pre-configured themes set language english, français, español note: arabic is available for the navigation system (if equipped) only. Touchscreen beep navigation turn-by-turn in cluster — if equipped controls screen time-out — if equipped fuel saver display ...

  • Page 466

    Clock after pressing the “clock” button on the touchscreen, the following settings will be available: setting name selectable options sync time with gps — if equipped set time hours + – set time minutes + – time format 12hrs 24hrs show time in status bar — if equipped note: the “show time in status ...

  • Page 467

    Camera after pressing the “camera” button on the touchscreen, the following settings will be available: setting name selectable options parkview backup camera delay — if equipped note: the “parkview backup camera delay” setting determines whether or not the screen will display the rear view image wi...

  • Page 468

    Safety & driving assistance after pressing the “safety & driving assistance” button on the touchscreen, the following settings will be available: setting name selectable options parksense sound only sound and display note: the rear park assist system will scan for objects behind the vehicle when the...

  • Page 469

    Setting name selectable options parkview backup camera note: your vehicle may be equipped with the parkview rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is put into reverse. The image will be displayed on the radio ...

  • Page 470

    Setting name selectable options rain sensing auto wipers — if equipped on off note: when the “rain sensing auto wipers” feature is selected, the system will automatically activate the windshield wip- ers if it senses moisture on the windshield. Hill start assist — if equipped on off mirrors & wipers...

  • Page 471

    Lights after pressing the “lights” button on the touchscreen, the following settings will be available: setting name selectable options headlight off delay + – note: when the “headlight off delay” feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 second...

  • Page 472

    Setting name selectable options flash lights with lock note: when the “flash lights with lock” feature is selected, the exterior lamps will flash when the doors are locked or un- locked with the key fob. This feature may be selected with or without the sound horn on lock feature selected. Doors & lo...

  • Page 473

    Setting name selectable options flash lights with lock note: when the “flash lights with lock” feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the key fob. This feature may be selected with or without the “sound horn with lock” fea- ture sel...

  • Page 474

    Setting name selectable options passive entry — if equipped note: the “passive entry” feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons. Personal settings linked to key fob — if equipped note: • the “personal settings linked to key ...

  • Page 475

    Engine off options after pressing the “engine off options” button on the touchscreen, the following settings will be available: setting name selectable options engine off power delay + – note: when the “engine off power delay” feature is selected, the power window switches, radio, uconnect phone sys...

  • Page 476

    Air suspension — if equipped after pressing the “suspension” button on the touchscreen, the following settings will be available: setting name selectable options sound horn with lower note: when the “sound horn with lower” feature is selected, a short horn sound will occur when the key fob remote lo...

  • Page 477

    Setting name selectable options tire jack mode note: when the “tire jack mode” feature is selected, the air suspension system is disabled to assist with changing a spare tire. Transport mode note: when the “transport mode” feature is selected, the air suspension system lowers and then disables to as...

  • Page 478

    Trailer brake after pressing the “trailer brake” button on the touch- screen, the following settings will be available: setting name selectable options trailer select trailer 1 trailer 2 trailer 3 trailer 4 trailer brake type light electric heavy electric light eoh heavy eoh audio after pressing the...

  • Page 479

    Setting name selectable options speed adjusted vol- ume off 1 2 3 note: the “speed adjusted volume” feature increases or decreases volume relative to vehicle speed. Surround sound — if equipped on off note: the “surround sound” feature provides simulated surround sound mode. Aux volume offset — if e...

  • Page 480

    Phone settings after pressing the “phone settings” button on the touch- screen, the following settings will be available: setting name selectable options do not disturb list of settings note: press “do not disturb” to access the available settings. The following settings are: auto reply (both, text,...

  • Page 481

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touchscreen, the following settings will be available: setting name selectable options tune start on off note: the “tune start” feature begins playing the current song from the beginning when you tune to a music channel u...

  • Page 482

    Restore settings after pressing the “restore settings” button on the touch- screen, the following settings will be available: setting name selectable options restore settings ok cancel note: when the “restore settings” feature is selected it will reset all settings to their default settings. System ...

  • Page 483

    Steering wheel audio controls — if equipped the remote sound system controls are located on the back surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push-button in the center. Pushing the top of the switch will incre...

  • Page 484

    Cd player — if equipped pushing the top of the switch once will go to the next track on the cd. Pushing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within eight seconds after the current track begins to play. If you p...

  • Page 485

    Radio operation and mobile phones under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the mobile phone antenna. This condition is not harmful to the radio. If your radio...

  • Page 486

    Note: • this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment gener- ates, uses and...

  • Page 487

    Uconnect 3 uconnect 4c/4c nav 10 multimedia 485.

  • Page 488

    Get started all you need to control your uconnect system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing instruc- tions. 2. Reduce background noise. Wind noise and passenger conversations ar...

  • Page 489

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect system. Push the vr button . After the beep, say: • “cancel” to stop a current voice session • “help” to hear a list of suggested voice commands • “repeat” to listen to the system prompts again no...

  • Page 490

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio stations you would like to hear. (subscrip- tion or included siriusxm satellite radio trial required.) push the vr button . After the beep, say: • “ tune to ninety-five-point-five fm” • “ tune to satellite channel hits 1” ...

  • Page 491

    Uconnect 3.0 uconnect 3 10 multimedia 489.

  • Page 492

    Media uconnect offers connections via usb, bluetooth and auxil- iary ports (if equipped). Voice operation is only available for connected usb and aux devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands and fol...

  • Page 493

    Tip: press the browse button on the touchscreen to see all of the music on your usb device. Your voice command must match exactly how the artist, album, song and genre information is displayed. Uconnect 3.0 uconnect 3 10 multimedia 491.

  • Page 494

    Phone making and answering hands-free phone calls is easy with uconnect. When the phonebook button is illuminated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the followi...

  • Page 495

    Tip: when providing a voice command, push the phone button and say “call,” then pronounce the name exactly as it appears in your phone book. When a contact has multiple phone numbers, you can say “call john smith work.” uconnect 3.0 uconnect 3 10 multimedia 493.

  • Page 496

    Climate (4c/4c nav) too hot? Too cold? Adjust vehicle temperatures hands-free and keep everyone comfortable while you keep moving ahead. (if vehicle is equipped with climate control.) push the vr button . After the beep, say one of the following commands: • “ set driver temperature to 70 degrees ” •...

  • Page 497

    Navigation (4c nav) the uconnect navigation feature helps you save time and become more productive when you do not know exactly how to get to where you want to go. (navigation is optional on the uconnect 4c system.) 1. To enter a destination, push the vr button . After the beep, say: “ find address ...

  • Page 498

    Siriusxm guardian (4c nav) — if equipped caution! Some siriusxm guardian services, including sos call and roadside assistance call will not work without an operable lte (voice/data) or 3g or 4g (data) net- work connection compatible with your device. Note: your vehicle may be transmitting data as au...

  • Page 499

    3. Select “customer care” to speak with a siriusxm guardian customer care agent who will activate ser- vices in your vehicle, or select “enter email” to activate on the web. For further information: • u.S. Residents visit: siriusxm.Com/guardian • canadian residents visit: siriusxm.Com/guardian/ca mo...

  • Page 500

    Push the vr button . After the beep, say one of the following commands: • show fuel prices • show 5 - day weather forecast • show extended weather tip: traffic alerts are not accessible with voice command. Apple carplay — if equipped apple carplay allows you to use your voice to interact with siri t...

  • Page 501

    Refer to your uconnect owner’s manual supplement for further information. Android auto — if equipped android auto allows you to use your voice to interact with android’s best-in-class speech technology through your vehicle’s voice recognition system, and use your smart- phone’s data plan to project ...

  • Page 502

    Refer to your uconnect owner’s manual supplement for further information. General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standa...

  • Page 503

    Uconnect system support: • u.S. Residents visit driveuconnect.Com or call: 1-877- 855-8400(24 hours a day 7 days a week) • canadian residents visit driveuconnect.Ca or call: 1-800- 465-2001(english) or 1-800-387-9983(french) siriusxm guardian services support: • u.S. Residents call:1-844-796-4827 • ...

  • Page 505

    Customer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . .504 ▫ prepare for the appointment . . . . . . . . . . . . . .504 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . .504 ▫ be reasonable with requests . . . ...

  • Page 506

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 507

    Any communication to the manufacturer’s customer center should include the following information: • owner’s name and address • owner’s telephone number (home and office) • authorized dealer name • vehicle identification number (vin) • vehicle delivery date and mileage fca us llc customer center p.O....

  • Page 508

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommunica- tion devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 509

    Warning! Engine exhaust (internal combustion engines only), some of its constituents, and certain vehicle compo- nents contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids con- tained in vehicles and c...

  • Page 510

    In canada if you believe that your vehicle has a safety defect, you should contact the customer service department imme- diately. Canadian customers who wish to report a safety defect to the canadian government should contact transport canada, motor vehicle defect investigations and recalls at 1-800...

  • Page 511

    Index 12.

  • Page 512

    Adding engine coolant (antifreeze) . . . . . . . . . . . . .383 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .287 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . .288, 428 adjust down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45, 46 forward...

  • Page 513

    Fluid type . . . . . . . . . . . . . . . . . . . . . . . . . .387, 435 shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .247 special additives . . . . . . . . . . . . . . . . . . . . . . . . .388 axle fluid . . . . . . . . . . . . . . . . . . . . . . . . .390, 391, 435 axle lubri...

  • Page 514

    Child restraints . . . . . . . . . . . . . . . . . . . . . . . . .204 child seat installation . . . . . . . . . . . . . . . . . .220, 221 how to stow an unused alr seat belt . . . . . . . .218 infants and child restraints . . . . . . . . . . . . . . . .207 locating the latch anchorages . . . . . . ....

  • Page 515

    Door ajar light. . . . . . . . . . . . . . . . . . . . . . . . . . . .150 door locks, automatic . . . . . . . . . . . . . . . . . . . . . . .39 door opener, garage. . . . . . . . . . . . . . . . . . . . . . . . .99 driver’s seat back tilt . . . . . . . . . . . . . . . . . . . . . . . .41 driving thr...

  • Page 516

    Exterior lights . . . . . . . . . . . . . . . . . . . . . . . . . .67, 234 filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . .366 air conditioning . . . . . . . . . . . . . . . . . . . . . .94, 370 engine fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . .433 engin...

  • Page 517

    General information. . . . . . . . . . . . . . . . . . . . . . . . .178 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . .421 grocery bag retainer. . . . . . . . . . . . . . . . . . . . . . . . .53 gross axle weight rating. . . . . . . . . . . . . . . . . . . . .291 gross vehicle...

  • Page 518

    Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .343 key fob panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 programming additional key fobs . . . . . . . . . .25, 32 key fob battery service (remote keyless entry) . . . . .22 key fob programming (remote ...

  • Page 519

    Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 seat belt reminder . . . . . . . . . . . . . . . . . . . . . . .147 security alarm . . . . . . . . . . . . . . . . . . . . . . . . . .148 service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323 tire pressure...

  • Page 520

    Occupant restraints . . . . . . . . . . . . . . . . . . . . . . . . .179 octane rating, gasoline (fuel) . . . . . . . . . . . . . . . . .428 oil, engine . . . . . . . . . . . . . . . . . . . . . . . . . . . .365, 433 capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .432 change in...

  • Page 521

    Rearward . . . . . . . . . . . . . . . . . . . . . . . . . . . .44, 46 recline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45, 46 up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45, 46 p...

  • Page 522

    Automatic locking retractor (alr) . . . . . . . . . . .191 lap/shoulder belt operation . . . . . . . . . . . . . . . .184 lap/shoulder belt untwisting . . . . . . . . . . . . . . .185 pregnant women . . . . . . . . . . . . . . . . . . . . . . . . .190 seat belt extender . . . . . . . . . . . . . . ....

  • Page 523

    Signals, turn . . . . . . . . . . . . . . . . . . . . . . . .73, 155, 234 snow chains (tire chains) . . . . . . . . . . . . . . . . . . . .412 snow plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .306 snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .408 spare ...

  • Page 524

    Load capacity . . . . . . . . . . . . . . . . . . . . . . .398, 399 pressure monitor system (tpms) . . . . . . . . . . . . .172 pressure warning light . . . . . . . . . . . . . . . . . . . .152 quality grading . . . . . . . . . . . . . . . . . . . . . . . . .416 radial . . . . . . . . . . . . . . . ...

  • Page 525

    Uconnect customer programmable features . . . . . . . . . . . . .451 uconnect settings . . . . . . . . . . . . . . . . . . . . . . . .441 uconnect settings . . . . . . . . . . . . . . . . . . . . . . . .451 uconnect settings customer programmable features . . . . . . .36, 449, 470 passive entry prog...

  • Page 526

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 527

    Second edition rev 1 printed in the u.S.A. ©2017 fca us llc. All rights reserved. Ram is a registered trademark of fca us llc. 18dd-126-ab c h a s s i s c a b o w n e r ’ s m a n u a l 2 0 1 8 promaster 2018.