1. DL manuals
  2. RAM
  3. Automobile
  4. promaster 2015
  5. Owner's Manual

RAM promaster 2015 Owner's Manual

Summary of promaster 2015

  • Page 1

    P r o m a s t e r o w n e r ’ s m a n u a l 2 0 1 5 2015 promaster 15vf-126-af sixth edition printed in u.S.A. Fca us llc.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .4 䡵 warnings and cautions . . . . . . . . . . . . . .6 䡵 van conversions/campers . . . . . . . . . . . .6 䡵 vehicle identification number . . . . . . . .6 䡵 vehic...

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engine...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importan...

  • Page 9

    Frame and underbody as well as the automobile infor- mation disclosure label affixed to a window on your vehicle, the vehicle registration and title. Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seri...

  • Page 11

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .11 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .11 ▫ locking doors with a key . . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .13 䡵 sentry ke...

  • Page 12

    䡵 power door locks . . . . . . . . . . . . . . . . . . .20 ▫ automatic door locks . . . . . . . . . . . . . . . . . .21 ▫ auto unlock doors . . . . . . . . . . . . . . . . . . . .22 䡵 windows . . . . . . . . . . . . . . . . . . . . . . . . . . .22 ▫ power windows . . . . . . . . . . . . . . . . . . ...

  • Page 13

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key, simply push the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized ...

  • Page 14

    3. Remove the key from the ignition switch lock cylinder. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park and re- move the key fob from the vehicle. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or...

  • Page 15

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unatt...

  • Page 16

    Note: a key which has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. If the vehicle security light is on after the key is turned to the on/run position, it indicates that there is a problem with the electronics. Cau...

  • Page 17

    • this device must accept any interference that may be received, including interference that may cause unde- sired operation. Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Vehicle security alarm...

  • Page 18

    The vehicle security alarm will also disarm if a pro- grammed sentry key® is inserted into the ignition switch. To exit the alarming mode, push the rke trans- mitter unlock button, or insert a programmed sentry key® into the ignition switch. The vehicle security alarm is designed to protect your veh...

  • Page 19

    Remote keyless entry (rke) this system allows you to lock or unlock the doors from distances up to approximately 66 ft (20 m) using a hand-held remote keyless entry (rke) transmitter. The rke transmitter does not need to be pointed at the vehicle to activate the system. Note: the line of transmissio...

  • Page 20

    Unlock the cargo area (rear lateral sliding doors and rear door). The turn signal lights will flash to acknowledge the unlock signal. To lock the doors push and release the lock button on the rke transmit- ter to lock all doors. The turn signal lights will flash to acknowledge the signal; the horn w...

  • Page 21

    3. Take out the battery case. Remove and replace the battery observing its polarity. 4. Refit the battery case inside the key fob and turn the screw to lock it into place. General information this device complies with part 15 of the fcc rules and rss-210 of industry canada. Operation is subject to t...

  • Page 22

    2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or cb radios. Power door locks the central lock/unlock button has an led that indicates whether the doors are locked or unlocked. • led on: doors locked. Push central lock/ unlock button once agai...

  • Page 23

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • for personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • before ex...

  • Page 24

    Auto door lock feature can be enabled or disabled through the evic or the uconnect® system. Auto unlock doors this feature unlocks all doors when the driver door is open. Windows power windows the control on the left front door panel has up-down switches that give you fingertip control of all power ...

  • Page 25

    Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pe...

  • Page 26

    Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: occupant restraint systems features • seat belt systems • supplemental restraint systems (srs) air bags • child restraints some of the safety features described in this section may be sta...

  • Page 27

    4. Never allow children to slide the shoulder belt behind them or under their arm. 5. You should read the instructions provided with your child restraint to make sure that you are using it properly. 6. All occupants should always wear their lap and shoulder belts properly. 7. The driver and front pa...

  • Page 28

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 29

    Unoccupied). The beltalert warning sequence starts by blinking the seat belt reminder light and sounding an intermittent chime. Once the beltalert warning sequence has completed, the seat belt reminder light will remain on until the seat belts are buckled. The beltalert warning sequence may repeat b...

  • Page 30

    The seat belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoul- der part of the seat belt to move freely with you under normal conditions. However, in a collision the seat belt will lock and reduce your risk of striking the inside of the vehicle ...

  • Page 31

    Warning! (continued) • wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of the seat belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • two people ...

  • Page 32

    Warning! (continued) forward, increasing the possibility of injury. Wear your seat belt snugly. • a seat belt that is worn under your arm is danger- ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A seat belt worn under the arm can caus...

  • Page 33

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 34

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automaticall...

  • Page 35

    3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Adjustable upper shoulder belt anchorage in the driver and...

  • Page 36

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton. To verify the shoulder belt anchorage is latched, pull downward on the shou...

  • Page 37

    Seat belts and pregnant women seat belts must be worn by all occupants including pregnant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong b...

  • Page 38

    The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately. Energy management feature the front seat belt system is equipped with an energy manag...

  • Page 39

    If the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt r...

  • Page 40

    Warning! (continued) younger, including a child in a rear-facing child restraint. • only use a rear-facing child restraint in a vehicle with a rear seat. How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until th...

  • Page 41

    Supplemental restraint systems (srs) some of the safety features described in this section may be standard equipment on some models, or may be optional equipment on others. If you are not sure, ask your authorized dealer. The air bag system must be ready to protect you in a collision. The occupant r...

  • Page 42

    The orc turns on the air bag warning light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is in the mar/acc/on/run position. After the self-check, the air bag warning light will turn off. If the orc detects a malfunction in any part of the s...

  • Page 43

    Warning! Ignoring the air bag warning light in your instru- ment panel could mean you won’t have the air bag system to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive,...

  • Page 44

    Warning! • being too close to the steering wheel or instrument panel during front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-facing chil...

  • Page 45

    Warning! (continued) because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to...

  • Page 46

    The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The front air bags fully inflate in less time than it takes to blink your eyes. The front air bags then quickly deflate while helping to res...

  • Page 47

    Deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the sab inflates. Children are at an even greater...

  • Page 48

    The sabic deploys downward, covering the side win- dows. An inflating sabic pushes the outside edge of the headliner out of the way and covers the window. The sabics inflate with enough force to injure occupants if they are not belted and seated properly, or if items are positioned in the area where...

  • Page 49

    Deploy independently; a left side impact deploys the left side air bags only and a right-side impact deploys the right side air bags only. Vehicle damage by itself is not a good indicator of whether or not side air bags should have deployed. The side air bags will not deploy in all side collisions, ...

  • Page 50

    Warning! • side air bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • being too close to the side air bags during deploy- ment could cause you to be severely injured or killed. • relying on the side air bags alone could lead to more severe in...

  • Page 51

    • seat belt pretensioners • seat belt buckle switch if a deployment occurs the front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a coll...

  • Page 52

    Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the seat belt retractor assemblies replaced by an authorized dealer imme- diately. Also, have the occupant restraint controller system serviced as well. Not...

  • Page 53

    Note: after an accident, remember to cycle the ignition to the stop (off/lock) position and remove the key from the ignition switch to avoid draining the battery. Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine com- partment and fuel tank before...

  • Page 54

    Warning! (continued) off switch, carefully check for fuel leaks or damage to the vehicle electrical devices (e.G. Headlights). Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag syste...

  • Page 55

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 56

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Chil...

  • Page 57

    Note: • for additional information, refer to www.Safercar.Gov/ parents/index.Htm or call: 1–888–327–4236 • canadian residents should refer to transport canada’s website for additional information: http://www.Tc.Gc.Ca/eng/motorvehiclesafety/ safedrivers-childsafety-index-53.Htm summary of recommendat...

  • Page 58

    Child size, height, weight or age recommended type of child restraint children too large for child restraints children 12 years old or younger, who have out-grown the height or weight limit of their booster seat vehicle seat belt, seated in the rear seat of the vehicle infant and child restraints sa...

  • Page 59

    Warning! (continued) • only use a rear-facing child restraint in a vehicle with a rear seat. Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and conver...

  • Page 60

    Warning! (continued) the vehicle seat position. When the vehicle seat has been adjusted, reinstall the child restraint. • when your child restraint is not in use, secure it in the vehicle with the seat belt or latch anchor- ages, or remove it from the vehicle. Do not leave it loose in the vehicle. I...

  • Page 61

    Move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly. Warning! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in se...

  • Page 62

    Installing child restraints using the vehicle seat belt child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt. Warning! • improper installation or failure to properly secure a child restraint can lead to failure of the restrai...

  • Page 63

    Front bucket seat automatic locking retractor (alr) location alr = switchable automatic locking retractor front bench seat automatic locking retractor (alr) locations alr = switchable automatic locking retractor 2 things to know before starting your vehicle 61.

  • Page 64

    Installing a child restraint with a switchable automatic locking retractor (alr) child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt. Warning! • improper installation or failure to properly secure a child restraint can lead ...

  • Page 65

    8. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Transporting pets air bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and...

  • Page 66

    Reactivating the fuel cut off switch: 1. Push the button a to reactivate the fuel cut off switch. Warning! Before reactivating the fuel cut off switch, carefully check for fuel leaks or damage to vehicle electrical devices (e.G. Headlights). Engine break-in recommendations a long break-in period is ...

  • Page 67

    The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to “maintenance procedures...

  • Page 68

    Warning! (continued) • be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoi...

  • Page 69

    Damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Safety checks you should make ...

  • Page 70

    Floor mat safety information always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in o...

  • Page 71

    Warning! (continued) • if required, mounting posts must be properly in- stalled, if not equipped from the factory. Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle. Periodi...

  • Page 73

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 ▫ inside day/night mirror — if equipped . . . . .74 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . .74 ▫ outside mirrors folding feature . . . . . . . . . . .75 ▫ ...

  • Page 74

    ▫ headlights . . . . . . . . . . . . . . . . . . . . . . . . . . .94 ▫ dimmer controls . . . . . . . . . . . . . . . . . . . . . .94 ▫ daytime running lights — if equipped . . . . . .94 ▫ battery saver . . . . . . . . . . . . . . . . . . . . . . . . .95 ▫ fog lights — if equipped . . . . . . . . . ....

  • Page 75

    ▫ to vary the speed setting . . . . . . . . . . . . . . .104 ▫ to accelerate for passing . . . . . . . . . . . . . . . .106 䡵 parksense® rear park assist — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .107 ▫ parksense® rear park assist sensors. . . . . . . .107 ▫ parksense® rear p...

  • Page 76

    Mirrors inside day/night mirror — if equipped a two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (towa...

  • Page 77

    Warning! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are. Relying too much on side convex mirrors could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle...

  • Page 78

    Switch. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the control to the center position “o” to prevent accidentally moving a mirror. Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature is act...

  • Page 79

    If the mirror head or pivot exhibits a slight amount of play, the mirror should be power folded closed, then power folded open (this may require multiple button pushes). Note: the intended use of the power fold mirrors is by pushing the buttons to fold and unfold the mirrors. Only manually fold the ...

  • Page 80

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 81

    Forward and rearward adjustment the adjusting bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rear- ward. Release the bar once the seat is in the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the se...

  • Page 82

    Height adjustment (without swivel seat) — if equipped the height adjusting levers are located on the center outboard side of the seat. Lift up on the front lever to adjust the front of the seat up or down. Lift up on the rear lever to adjust the rear of the seat up or down. Height adjustment levers ...

  • Page 83

    Height adjustment (with swivel seat) — if equipped the height adjusting knobs are located on the center outboard side of the seat. Rotate the front knob to adjust the front of the seat up or down. Rotate the rear knob to adjust the rear of the seat up or down. Height adjustment knobs 1 — front heigh...

  • Page 84

    Recliner adjustment — without swivel seat the recliner knob is on the rear outboard side of the seat. To recline the seatback, lean back, rotate the knob rear- ward to position the seatback as desired. To return the seatback to its normal upright position, lean forward, rotate the knob forward until...

  • Page 85

    Outward. Release the lever once the seatback is in the upright position. Warning! • adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust the seat only ...

  • Page 86

    Damper weight adjustment use the weight adjustment knob to set the required setting based on body weight, with settings between 88 lbs (40 kg) and 286 lbs (130 kg). Swivel seat — if equipped the swivel seat lever is located at the lower front inboard side of the seat. The seat may be turned through ...

  • Page 87

    Are both locked in facing forward position. When the seats are not in the right position and the first vehicle movement after the cranking is attempted, a chime and a text message will appear in evic. Rotate and lock the swivel seats in the correct position before trying again. If the driver or the ...

  • Page 88

    The fold-down flap is equipped with two cup holders and a support surface with a paper holder clip. Underseat storage tray (driver side only) — if equipped a storage tray is located under the drivers seat that can be easily removed by withdrawing the hooks on the support base. Fold-down flap pull ta...

  • Page 89

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the lower outboard side of the seat. Push the switch once to turn on the heated seats. Push the...

  • Page 90

    Note: once a heat setting is selected, heat will be felt within two to five minutes. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care...

  • Page 91

    Front head restraints to raise the head restraint pull upward on the head restraint. To lower the head restraint, push the adjust- ment button located on the base of the head restraint and push downward on the head restraint. To remove the head restraint, raise it up as far as it can go then push th...

  • Page 92

    Warning! • a loose head restraint thrown forward in a colli- sion or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow removed head restraints in a location outside the occupant compartment. • all the head restraints must be reinstalled in the vehicle to...

  • Page 93

    Turn the adjuster wheel to the right or left to adjust the height of the armrest up or down. To open and close the hood to open the hood, two latches must be released. 1. Open the drivers door to gain access to the hood release lever. Pull the hood release lever located on the side of the instrument...

  • Page 94

    2. Move to the outside of the vehicle, reach into the opening beneath the center of the hood and push the safety latch lever to the right to release it, before raising the hood. 3. Raise the hood and place the hood prop rod in hood slot to secure the hood in the open position. Caution! To prevent po...

  • Page 95

    Caution! (continued) • do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is fully latched before driving yo...

  • Page 96

    Headlights to turn on the headlights, turn the end of the multifunction lever to the headlight position. When the headlight switch is on, the parking lights, taillights, license plate light, the clear- ance lights and instrument panel lights are also turned on. To turn off the headlights, turn the e...

  • Page 97

    To activate the daytime running lights (drl), rotate the end of the multifunction lever to the o (off) position. Note: the low beams and side/taillights will not be on with drl. The drl function may be programmed to be on or off through the uconnect® system screen if equipped, or through the instrum...

  • Page 98

    Parking lights these lights can only be turned on with ignition key in the stop position or removed, by moving the end of the multifunction lever to o (off) position and then to the headlight position. The warning light telltale in the instrument panel comes on. The lights stay on until the next ign...

  • Page 99

    Activation remove the key or turn the ignition to the off/lock position, and pull the multifunction lever toward the steering wheel, within two minutes. Each time the lever is pulled, the activation of the lights will be extended by 30 seconds. The activation of the lights can be extended to a maxim...

  • Page 100

    • push the right switch to the right to turn on the right map light. Cargo lamp the rear cargo lamp is located at the upper rear cargo area above the rear doors. Map/dome lights 1 — auto/off 3 — left map 2 — dome 4 — right map rear cargo lamp 98 understanding the features of your vehicle.

  • Page 101

    Your vehicle may be equipped with a side cargo lamp located at the upper rear area of the passenger side sliding door opening. The cargo lamps can be set to three different positions (off/right position, center position, on/left position). • push the cargo lamp lens to the right from its center posi...

  • Page 102

    Note: the windshield wipers/washers will only oper- ate with the ignition in the on/run position. Intermittent wiper system push the lever downward to the first detent and rotate the center ring to use one of the four intermittent wiper settings when weather conditions make a single wiping cycle, wi...

  • Page 103

    Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Windshield washer operation to use the washer, pull the windshield wiper/washer lever toward the ...

  • Page 104

    To unlock the steering column, pull the control handle up. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle down until fully engaged. Warning! Do not adjust the steering column w...

  • Page 105

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by rotating the electronic speed control on/off ce...

  • Page 106

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 107

    The drivers preferred units can be selected through the radio settings if equipped. Refer to ”uconnect settings” in “understanding your instrument panel” for more information. The speed increment shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • tapping t...

  • Page 108

    • if the lever is continually held down, the set speed will continue to decrease until the lever is released, then the new set speed will be established. Metric speed (km/h) • tapping the speed control lever down (-) once will result in a 1 km/h decrease in set speed. Each subse- quent tap of the le...

  • Page 109

    Parksense® rear park assist — if equipped the parksense® rear park assist system provides an audible indication of the distance between the rear fascia/bumper and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to parksense® system usage precautions for limitations of this...

  • Page 110

    If several obstacles are detected, the parksense® rear park assist system indicates the nearest obstacle. The minimum height of a detectable obstacle corre- sponds to the maximum height of an obstacle that would clear the underside of the car during the parking maneu- ver. Parksense® rear park assis...

  • Page 111

    Audible and visual signals supplied by the parksense® rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loudspeaker) • sound pulses emitted at a rate that in- creases as the distance decreases. • emi...

  • Page 112

    While audible signals are emitted, the audio system is not muted. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the distance measured by the inner sensors is constant. If this condition occurs for the external sensors, the signal is turned...

  • Page 113

    Parksense® rear park assist system usage precautions note: • ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the rear park assist system operating properly. • jackhammers, large trucks, and other vibrations co...

  • Page 114

    Caution! (continued) when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using parksense®. Warning! • drivers must be careful when backing up even when using parksense®. Always check carefully behind your vehicle, look behind you, and be sure to check for...

  • Page 115

    Parkview rear back up camera — if equipped your vehicle may be equipped with the parkview rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse and/or when the rear doors are opened. The image will be displ...

  • Page 116

    When displayed, static grid lines will illustrate the width of the vehicle and will show separate zones that will help indicate the distance to the rear of the vehicle. The following table shows the approximate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm...

  • Page 117

    Caution! (continued) unable to view every obstacle or object in your drive path. • to avoid vehicle damage, the vehicle must be driven slowly when using parkview to be able to stop in time when an obstacle is seen. It is recom- mended that the driver look frequently over his/her shoulder when using ...

  • Page 118

    • push the right switch to the right to turn on the right map light. Power outlets — if equipped passenger compartment power outlet the cigar lighter and the power outlet are located in the center console. It only operates with the ignition key at mar/on. Map/dome lights 1 — auto/off 3 — left map 2 ...

  • Page 119

    Load compartment power outlet the load compartment power outlet is located on the left rear side of the rear cargo compartment. The outlet can be is used for powering 12 volt adaptive accessories and recharging communications devices. Note: do not connect devices with power higher than 180 w to the ...

  • Page 120

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 121

    Cigar lighter and ash receiver — if equipped a removable ash receiver and cigar lighter are available. Cupholders the cupholders for the drivers and passenger area are located near the floor just under the center stack storage compartment. There are cupholders located in each door panel as well as o...

  • Page 122

    Storage glove compartments the glove compartments are located on the right side of the instrument panel. Glove compartments 1 — upper glove compartment 2 — lower glove compartment 120 understanding the features of your vehicle.

  • Page 123

    Front door storage — if equipped storage areas and bottle holders are located in both the front door trim panels. Dash storage the dash storage is located on the right side of the instrument panel. Front door storage dash storage 3 understanding the features of your vehicle 121.

  • Page 124

    Dashboard clipboard located on top of the dashboard is a clipboard and two storage bins on each side of the clipboard. Cargo area features cargo area the cargo area may be equipped with different options such as a optional side panels, rear seats and an optional floor. Clipboard and storage bins 122...

  • Page 125

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .126 䡵 instrument cluster . . . . . . . . . . . . . . . . .127 䡵 instrument cluster descriptions . . . . .128 䡵 electronic vehicle information center (evic) . . . . . . . . . . . . . . . . . . . . . . . .141 ▫...

  • Page 126

    ▫ uconnect® rh3 display. . . . . . . . . . . . . . . . .154 ▫ general functions and settings . . . . . . . . . . .155 ▫ tuner mode (am/fm radio) . . . . . . . . . . . . .157 ▫ setup menu . . . . . . . . . . . . . . . . . . . . . . . . .160 ▫ clock . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 127

    ▫ radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191 ▫ media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 ▫ voice text reply . . . . . . . . . . . . . . . . . . . . . .193 ▫ additional information . . . . . . . . . . . . . . . . .195 4 understanding your instrument...

  • Page 128

    Instrument panel features 1 — air outlet 10 — lower glove compartment 19 — uconnect® phone buttons 2 — multifunction lever (external lights) 11 — cup holder 20 — tilt steering column release lever 3 — instrument cluster 12 — usb charger/12v 21 — horn 4 — multifunction lever (front/rear wiper, trip c...

  • Page 129

    Instrument cluster 4 understanding your instrument panel 127.

  • Page 130

    Instrument cluster descriptions 1. Speedometer the speedometer shows the vehicle speed in miles per hour (mph) and/or kilometers per hour (km/h). 2. Turn signal indicators the arrow will flash with the exterior turn signal when the turn signal lever is operated. Note: • check for an inoperative outs...

  • Page 131

    6. Park/headlight on indicator — if equipped this indicator will illuminate when the park lights or headlights are turned on. 7. Odometer/trip odometer/electronic vehicle informa- tion center (evic) display area this display indicates the total distance the vehicle has been driven. U.S. Federal regu...

  • Page 132

    • daytime running lights • clearance lights • license plate lights the failure relating to these lights could be: • one or more blown bulbs • a blown protection fuse • a break in the electrical connection 9. Vehicle security light if during starting, the key code is not correctly recognized, the veh...

  • Page 133

    This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood. 13. Electronic speed control set indicator light this light will turn on when the electronic speed control is set. 14. Charging system light — if equipped this light shows the status of t...

  • Page 134

    Indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. Note: the light may flash momentarily during sharp cornering maneuvers, which change fluid level cond...

  • Page 135

    Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 16. Malfunction indicator light (mil) the malfunction indicator light (mil) is part of an onboard diagnostic (obdii) system which monitors the emissions and engine con- trol system. If th...

  • Page 136

    Warning! (continued) drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 17. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal...

  • Page 137

    Warning! (continued) vehicle.” follow the warnings under the “cooling system pressure cap” paragraph. 18. Engine temperature warning light this light warns of an overheated engine condition. As engine coolant temperatures rise and the gauge ap- proaches h , this indicator will illuminate, and a sing...

  • Page 138

    20. Tow/haul this light will illuminate when tow haul mode is selected. 21. Low fuel light when the fuel level reaches approximately 3.0 gal (11.7 l), this light will turn on, and remain on until fuel is added. 22. Fuel gauge/fuel door reminder when the ignition switch is in the on/run position, the...

  • Page 139

    24. Air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. R...

  • Page 140

    Combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction ...

  • Page 141

    Note: the tpms telltale is also accompanied by a “low tire” message in the electronic vehicle information cen- ter (evic). Refer to “tire pressure monitoring system (tpms) in “starting and operating” for further informa- tion. 26. Seat belt reminder light when the ignition switch is first turned to ...

  • Page 142

    (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. Note: • the “esc off indicator light” and the “esc activation/malfunction indicator light” come on momentarily each time the ignition switch is turned to ...

  • Page 143

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. This system allows the driver to select a variety of useful information by pushing the switches mounted on the instrument p...

  • Page 144

    • service (diesel only) • drl - daytime running light (if equipped) • exit menu the system allows the driver to select information by pushing the following buttons mounted on the instru- ment panel to the left of the steering column: • mode button push and hold the mode button for a time longer than...

  • Page 145

    • up arrow button push and release the up arrow button to scroll upward through the main menu and sub- menus or adjust the illumination on the instru- ment panel when the headlights are on. • down arrow button push and release the down arrow button to scroll downward through the main menu and submen...

  • Page 146

    • (*) just available after sbr disable made by chr service • service (diesel only) • drl - daytime running lights (if equipped) • exit menu note: • if equipped with uconnect® 5.0 radio, some cus- tomer programmable features will display in the uconnect® 5.0 system. Refer to the radio supplement for ...

  • Page 147

    3. Briefly push and release the mode button to select the displayed submenu option and to open the rel- evant setup menu. 4. Push and release the up or down button (by single pushes) to select the new setting for this submenu option. 5. Briefly push and release the mode button to store the new setti...

  • Page 148

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Trip computer the trip computer is located in the instrument cluster. It features a driver-interactive display (displays informa- tion such as tr...

  • Page 149

    Start of trip procedure with the ignition on, push and hold the trip button for over one second to reset. Exit trip to exit the trip function, wait until all the values have been displayed or hold the menu button for longer than one second. Briefly push and release the menu button to go back to the ...

  • Page 150

    Values displayed range this indicates the distance which may be traveled with the fuel remaining in the tank, assuming that driving conditions will not change. The message “----” will appear on the display in the following cases: • distance less than 30 miles (or 50 km). • the vehicle is parked for ...

  • Page 151

    Personal settings (customer-programmable features) • speed beep • trip b data • set time • set data • auto lock • units (distance, fuel economy, temperature) • language • buzzer volume • seat belt buzzer (*) • (*) just available after sbr disable made by chr service • service (diesel only) • drl - d...

  • Page 152

    According to the specific characteristics of the vehicle, with a design matching the style of the instrument panel. The radio is installed in an ergonomic position for the driver and passenger with a diagram on the front panel that allows the user commands to be identified quickly and easily. The di...

  • Page 153

    Radio reception reception varies constantly while driving. Reception may be affected by mountains, buildings or bridges, especially when further away from the transmit- ter of the tuned radio station. Caution! When listening to traffic news, you may notice louder volume compared to normal playback. ...

  • Page 154

    You must enter the security (shown on the ⬙ warranty card ⬙ , for example, 4359) code as follows: action display when you turn the radio on, the dis- play shows ⬙ 0000 ⬙ . 0000 push the number 1 preset button un- til the first digit of the code number is displayed. 4 - - - push the number 2 preset b...

  • Page 155

    General the radio offers the following features: radio (tuner mode) • automatic/manual station tuning • manual storage of 30 stations: 18 in the fm band (6 in fm1, 6 in fm2 and 6 in fm3), 6 in the am1 band and 6 in the am2 band • best stations memory mp3/wma/aac (usb mode) • “last position” memory •...

  • Page 156

    Uconnect® rh3 display description of commands rotary knob: turn radio on and off, volume, forward/ reverse track, confirm selected option. 䉴䉴 and 䉳䉳 buttons: station search in automatic mode, station search in manual mode, forward/reverse tracks, forward/reverse within track. Mute/pause button: inte...

  • Page 157

    Buttons 1 and 2: forward/reverse folder. Band/as button: select tuned frequency band, preset best stations. Menu button: access setup menu. General functions and settings turn the radio on or off to turn the radio on or off, push the rotary knob (push once to turn on and hold for about three seconds...

  • Page 158

    Repeatedly to change the equalization. If this button is not pushed again within five seconds, or if you push the rotary knob, the display returns to the previ- ously selected view and the settings will be saved. Custom audio setting functions push the audio button for less than two seconds to activ...

  • Page 159

    Knob counterclockwise to transfer the sound to the left-hand side; the display will show ⬙ bal l 01 ⬙ . The balance levels can be set between 0 and 15. Fader the display will show ⬙ fad 00 ⬙ to indicate that you can set the fader function. Turn the rotary knob clockwise to transfer the sound to the ...

  • Page 160

    St (stereo) when this is on, it indicates the radio station is transmit- ting. Searching for stations in automatic mode when you push or for less than two seconds, the radio will search for the next valid station. While the radio is searching for the new station, the display will show ⬙ seeking ⬙ . ...

  • Page 161

    When the or , audio, 1, 2, 3, 4, 5, 6, band/as buttons and src are pushed in ⬙ mute/paused ⬙ mode, these will be implemented and the audio will be restored without changing the original volume. Turn the rotary knob to restore the audio and change the volume to the level selected. The display will sh...

  • Page 162

    Presetting stations with a strong signal: when the band/as button is pushed for more than two seconds, the radio will search for the 6 best stations and automati- cally store them in the 6 memory positions of the current band. During the search, the display will indicate ⬙ fm ast ⬙ or ⬙ am ast ⬙ , d...

  • Page 163

    Indicating the maximum volume selected. When the maximum volume selected is the maximum radio vol- ume, the display will show ⬙ mvol off ⬙ . Auto switch this function changes the on/off sequence of the radio as described in the section: ⬙ turning the device on and off. ⬙ to enable it, turn the rotar...

  • Page 164

    Caution! (continued) due to the extensive range of makes and models of storage devices available on the market, not all devices have compatibility required for proper func- tioning of car radios. Use only quality usb devices. Due to the extensive range of brands and models of storage devices availab...

  • Page 165

    File sequence 4 understanding your instrument panel 163.

  • Page 166

    Play sequence (file) comments 1 track 1_1 if there are mp3, wma or aac (extensions mp3, wma, m4a, mp4 and 3gp) files in the root folder, these will be played first. 2 track 2_1 folders within the same level are sorted in ascending order by name (up to folder number 100, after which the order follows...

  • Page 167

    When these buttons are pushed, the display will show a ⬙ trkyyy ⬙ message, where yyy is the track number. If any of these buttons is briefly pushed again, the number in the display will continue changing according to the selected track. While the track is being selected, that is, when or are pushed ...

  • Page 168

    Mute/pause pushing this knob stops music playback and mutes the sound. The display will switch between ⬙ paused ⬙ and the current view (three seconds). Push this button again to resume music playback from the point where it left off, without changing the original volume level. The display will show ...

  • Page 169

    When the rotary knob is pushed or if its position is not changed for five seconds, the track is selected, the id3 tag is processed and the music will start playing. In this case, the display will show the ⬙ trkyyy ⬙ message for two seconds and then return to the default display defined by the disp f...

  • Page 170

    Whenever the radio skips from one folder to another, the display will show the name of the folder to which you are going for a few milliseconds (the rotary movements are ignored during this period) and a maximum of three seconds. When you reach the last folder and push button 1 again, the radio will...

  • Page 171

    Uconnect® settings the uconnect® system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allows you to access and change the customer programmable features. Many features can vary by vehicle. Caution! Do not attach any o...

  • Page 172

    Buttons on the faceplate buttons on the faceplate are located below the uconnect® system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.E., 30, 60, 90), push the ...

  • Page 173

    Buttons on the touchscreen buttons on the touchscreen are accessible on the uconnect® display. Customer programmable features/personal settings push the settings button on the faceplate to display the menu setting screen. In this mode the uconnect® system allows you to access programmable features t...

  • Page 174

    • display brightness with headlights on this feature allows you to select the display brightness when the headlights are on. Adjust the brightness with the ⬙ up ⬙ or ⬙ down ⬙ arrow buttons on the touchscreen. Then press the back arrow/done button on the touch- screen, or push the back button on the ...

  • Page 175

    • units — if equipped press the units button to select the correct unit for temperature (°f or °c), distance (mi or km) and fuel consumption. If the distance is in mi (miles), miles per gallon (mpg) are set automatically. If the distance is km, km/1 or 1/100km can be selected. • voice response lengt...

  • Page 176

    • set time minutes this feature allows you to adjust the minutes. The “sync with gps time” button on the touchscreen must be unchecked. To make your selection, press the ⬙ up ⬙ or ⬙ down ⬙ arrow buttons on the touchscreen to adjust the minutes up or down. Press the back arrow/done button on the touc...

  • Page 177

    Safety/assistance after pressing the safety/assistance button on the touch- screen the following settings will be available: • parkview® rear back up camera — if equipped your vehicle may be equipped with the parkview® rear back up camera static guidelines that allows you to see straight grid line o...

  • Page 178

    Doors & locks after pressing the “doors & locks” button on the touch- screen the following settings will be available: • auto door locks when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 12 mph (20 km/h). To make your selection, press the “auto lo...

  • Page 179

    Press the off, 1, 2 or 3 button on the touchscreen. Then press the back arrow/done button on the touchscreen. • loudness — if equipped loudness improves sound quality at lower volumes. To make your selection, press the “loudness” button on the touchscreen, then choose “on” or “off.” the button will ...

  • Page 180

    • paired audio sources this feature shows which audio devices are paired to the phone/bluetooth® system. For further information, refer to the uconnect® supplement manual. Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be ava...

  • Page 181

    • restore settings when this feature is selected it will reset the display, clock, audio, and radio settings to their default settings. To restore the settings to their default setting, press the restore settings button. A pop-up will appear asking ⬙ are you sure you want to reset your settings to d...

  • Page 182

    May not fully support the ipod® control features. Please visit apple’s website for software updates. For further information, refer to the uconnect® supple- ment manual. Usb charging port the usb connector port can be used for charging pur- poses only. Use the connection cable to connect an ipod® or...

  • Page 183

    Warning! Do not plug in or remove the ipod® or external device while driving. Failure to follow this warning could result in a collision. Steering wheel audio controls the remote sound system controls are located on the surface of the steering wheel. The right-hand control is a rocker-type switch an...

  • Page 184

    The following describes the right-hand control operation in each mode. Radio operation pushing the top of the switch will “scan” up for the next listenable station and pushing the bottom of the switch will “scan” down for the next listenable station. Cd disc maintenance to keep a cd in good conditio...

  • Page 185

    Harmful to the radio. If your radio performance does not satisfactorily “clear” by the repositioning of the phone, it is recommended that the radio volume be turned down or off during mobile phone operation when not using uconnect® (if equipped). General information this device complies with part 15...

  • Page 186

    The manual temperature controls consist of a series of three outer rotary dials (blower speed, temperature and mode) and three inner push buttons (recirculation, a/c, rear window defroster). Blower control rotate this control to regulate the amount of air forced through the ven- tilation system in a...

  • Page 187

    Air conditioning control push this button to engage the air conditioning. A light will illuminate when the air conditioning system is engaged. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures. •...

  • Page 188

    • bi-level air is directed through the panel and floor outlets. Note: for all settings, except full cold or full hot, there is a difference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets. This feature gives improved comfort during sunny but cool conditi...

  • Page 189

    Continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Ex- tended use of this mode is not recommended. The use of the recirculation mode in cold or damp weather will cause windows to fog on the inside, because of moisture buildup inside the vehicle. Sel...

  • Page 190

    Note: do not affix stickers to the inside of the heated rear window over the heating filaments, to avoid damage that might cause them to stop working properly. Additional rear climate control — if equipped this switch, mounted on the instrument panel to the left of the steering column, activates the...

  • Page 191

    Uconnect® 5.0 voice recognition quick tips introducing uconnect® start using uconnect® voice recognition with these helpful quick tips. It provides the key voice commands and tips you need to know to control your uconnect® 5.0 system. Key features: • 5.0” full color touchscreen display • bluetooth® ...

  • Page 192

    2. Reduce background noise. Wind and passenger con- versations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is positioned on the rearview mirror and aimed at the driver. 4. Each time you give a voice comma...

  • Page 193

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect® system. Push the vr button . After the beep, say ѧ • cancel to stop a current voice session • help to hear a list of suggested voice commands • repeat to listen to the system prompts again notice...

  • Page 194

    Push the vr button . After the beep, say ѧ • tune to ninety-five-point-five fm • tune to satellite channel hits 1 tip: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say “help.” the system will provide you with a list of commands. Media uconn...

  • Page 195

    Push the vr button . After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artist. • change source to bluetooth® • change source to ipod® • change source to usb • play artist beethoven; play album greatest hits; play song moonlight sonata; ...

  • Page 196

    1. Once an incoming text message is read to you, push the phone button . After the beep, say... “re- ply.” 2. Listen to the uconnect® prompts. After the beep, repeat one of the pre-defined messages and follow the system prompts. Pre-defined voice text reply responses yes. Stuck in traffic. See you l...

  • Page 197

    Additional information © 2016 fca us llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of fca us llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. Yelp, yelp logo, yelp...

  • Page 199

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .200 ▫ automatic transmission — if equipped . . . . .200 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .200 ▫ extreme cold weather (below –20°f or −29°c) . . . . . . . . . . . . . . . .201 ▫ if engine ...

  • Page 200

    䡵 parking brake . . . . . . . . . . . . . . . . . . . . . .218 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . .220 䡵 electronic brake control system . . . .220 ▫ four-wheel anti-lock brake system (abs) . . .220 ▫ traction control system (tcs) . . . . . . . . . . . .222 ▫ brake assist sys...

  • Page 201

    䡵 tire chains (traction devices) . . . . . . .252 䡵 tire rotation recommendations . . . . .253 䡵 tire pressure monitoring system (tpms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .254 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . .257 ▫ general information . . . . . . ...

  • Page 202

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 203

    Extreme cold weather (below –20°f or −29°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If engine fails to start warning! Never pour fuel or other flammable liquids into the thr...

  • Page 204

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 205

    Warning! (continued) once the key is removed, the transmission is locked in park, securing the vehicle against un- wanted movement. • when leaving the vehicle, always remove the igni- tion key from the vehicle and lock the vehicle. • never leave children alone in a vehicle, or with access to an unlo...

  • Page 206

    Off (key removal) position. The key can only be re- moved from the ignition when the ignition is in the lock/off position, and once removed the transmission is locked in park. Note: if a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety feature is i...

  • Page 207

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has park, reverse, neu- tral, drive, and electronic range select (ers) shift positi...

  • Page 208

    Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to...

  • Page 209

    Warning! (continued) vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal. • unintended movement of a vehicle could injure...

  • Page 210

    • when shifting into park, firmly move the shift lever all the way forward and to the left until it stops and is fully seated. • look at the transmission gear position display and verify that it indicates the park position (p). • with the brake pedal released, verify the shift lever will not move ou...

  • Page 211

    Caution! Towing the vehicle, coasting, or driving for any other reason with the transmission in neutral can cause severe transmission damage. Refer to “recreational towing” in “starting and operating” and “towing a disabled vehicle” in “what to do in emergencies” for further information. Drive (d) t...

  • Page 212

    Transmission limp home mode transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, transmission limp home mode is activated. In this mode, the transmission remains in third gear regardless of which forward gear ...

  • Page 213

    You set the transmission gear limit to 4 (fourth gear), the transmission will not shift above fourth gear, but will shift through the lower gears normally. You can switch between drive and ers mode at any vehicle speed. When the shift lever is in the drive position, the transmission will operate aut...

  • Page 214

    Note: to select the proper gear position for maximum deceleration (engine braking), move the shift lever into the ers position, then tap it forward (-) repeatedly as the vehicle slows. The transmission will shift to the range from which the vehicle can best be slowed down. Overdrive operation the au...

  • Page 215

    Torque converter clutch a feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati- cally at calibrated speeds. This may result in a slightly different feeling or response during normal operation i...

  • Page 216

    When there is a difference in the surface traction under the front (driving) wheels. Warning! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have a collision. Accelerate slowly an...

  • Page 217

    Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow- ing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicl...

  • Page 218

    Caution! (continued) standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • do not exceed 5 mph (8 km/h) when d...

  • Page 219

    Note: • increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that there is a problem with the power steering system. • upon initial start-up in cold weather, the power steer- ing pump may make noise for a short amount of time. This is due to the co...

  • Page 220

    Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid. If necessary, add fluid to restore to the proper indicated leve...

  • Page 221

    When the parking brake is applied with the ignition switch in the mar (acc/on/run) position, the brake warning light in the instrument cluster will illuminate. When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill gra...

  • Page 222

    Caution! If the brake warning light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Brake system your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems...

  • Page 223

    Modulate hydraulic pressure, to prevent wheel lock-up and to help avoid skidding on slippery surfaces. The system’s pump motor runs during an abs stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation, which is normal. The abs includes an amber abs wa...

  • Page 224

    The vehicle comes to a stop. This is the result of the system reverting to the base brake system. Engagement of the abs may be accompanied by a pulsing sensation. You may also hear a clicking noise. These occurrences are normal and indicate that the system is functioning properly. Traction control s...

  • Page 225

    Warning! (continued) • the tcs cannot prevent collisions, including those resulting from excessive speed in turns, or hydro- planing. • the capabilities of a tcs-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of othe...

  • Page 226

    Electronic stability control (esc) the electronic stability control (esc) enhances direc- tional control and stability of the vehicle under various driving conditions. Esc corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the ov...

  • Page 227

    Esc operating modes the “esc off” switch is located in the center switch bank, next to the hazard flasher switch. Esc on this mode is the normal operating mode for esc equipped vehicles. Whenever the vehicle is started, the esc system will be in this mode. This mode should be used for most driving s...

  • Page 228

    Warning! (continued) enhanced vehicle stability offered by the esc sys- tem is reduced. • trailer sway control (tsc) is disabled when the esc system is in the ⴖ partial off ⴖ mode. Note: to improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it...

  • Page 229

    The “esc activation/malfunction indicator light” also flashes when tcs is active. If the “esc activation/ malfunction indicator light” begins to flash during ac- celeration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing...

  • Page 230

    Attempt to stop the trailer from swaying. Tsc is disabled when the esc system is in the “partial off” mode. Warning! If tsc activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Hill start assist (hsa) the hsa system...

  • Page 231

    Warning! There may be situations on minor hills with a loaded vehicle, or while pulling a trailer, when the system will not activate and slight rolling may occur. This could cause a collision with another vehicle or object. Always remember the driver is responsible for brak- ing the vehicle. Towing ...

  • Page 232

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 233

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 234

    Example: r = construction code – ⬙ r ⬙ means radial construction, or – ⬙ d ⬙ means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating t...

  • Page 235

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 236

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 237

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 238

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 236 starting an...

  • Page 239

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 240

    Xxx kg” on the tire and loading information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and carg...

  • Page 241

    5 starting and operating 239.

  • Page 242

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 243

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 244

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judge- ment when determining proper inflation. Tires may look properly inflated even when they are under-inflated. • inspect tires for signs of tire wear or visible damage. Ca...

  • Page 245

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 246

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed symbol). Tire ...

  • Page 247

    Warning! Do not use summer tires in snow/ice conditions. You could lose vehicle control, resulting in severe injury or death. Driving too fast for conditions also creates the possibility of loss of vehicle control. Snow tires some areas of the country require the use of snow tires during the winter....

  • Page 248

    Run flat tire reaches the run flat mode it has limited driving capabilities and needs to be replaced immedi- ately. A run flat tire is not repairable. It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the run flat mode. See the tire pressure monit...

  • Page 249

    The tire and loading information placard located on the driver’s side door opening or on the sidewall of the tire. Compact spare tire descriptions begin with the letter “t” or “s” preceding the size designation. Example: t145/ 80d18 103m. T, s = temporary spare tire since this tire has limited tread...

  • Page 250

    Your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Limited-use spare — if equipped the limited-use spare tire is for temporary emergency use only. This tire is identified by a label located on the limited-use spare whe...

  • Page 251

    Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels fast...

  • Page 252

    Worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. Life of tire the service life of a tire is dependent upon varying factors including, but not limited to: • driving style. • tire pressure - improper cold tire inflati...

  • Page 253

    Wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed. Refer to the paragraph on “tread wear indicator”. Refer to the tire and loading information placard or ...

  • Page 254

    Warning! (continued) • never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • failure to equip your vehicle wi...

  • Page 255

    Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device clearance be- tween tires and other suspension components, it is important that only traction devices in good condi- tion are used. Broken devices can cause serious damage. S...

  • Page 256

    Tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a smooth, quiet ride. Refer to the “maintenance schedule” for the proper maintenance intervals. The reasons for any rapid or unusual wear should be corrected prior to rotation being perfor...

  • Page 257

    The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after th...

  • Page 258

    Pressure is sufficiently low enough to turn on the tire pressure monitoring telltale light. Driving the vehicle may cause the tire pressure to rise to approximately 27 psi (186 kpa), but the tire pressure monitoring telltale light will still be on. In this situation, the tire pressure monitoring tel...

  • Page 259

    • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handlin...

  • Page 260

    Tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster, an audible chime will be activated, and the “check tire pressure” text message will display when one or more of the four active road tire pressures are low. Should ...

  • Page 261

    1. The spare tire has a tire pressure monitoring sensor, but it is not monitored until it is mounted in place of any of the existing four road tires. 2. If you install the spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a...

  • Page 262

    Fuel requirements 3.6l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high-quality unleaded “regular” gaso- line having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide a...

  • Page 263

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in starting and drivability prob- lems, damage critical fuel system...

  • Page 264

    Mmt in gasoline methylcyclopentadienyl manganese tricarbonyl (mmt) is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended wi...

  • Page 265

    Caution! (continued) or malfunctioning and may require immediate ser- vice. Contact your authorized dealer for service assistance. • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel syste...

  • Page 266

    Warning! (continued) time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Copyright ©2016 fca us llc adding fuel fuel filler cap (gas cap) the gas cap is located behind the fuel filler door on the left side of the vehicle...

  • Page 267

    Caution! (continued) impurities into the fuel system and may cause the “malfunction indicator light (mil)” to turn on, due to fuel vapors escaping from the system. • to avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Warning! • never have any smoking materials lit ...

  • Page 268

    Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “check fuel cap” message will be displayed in the electronic vehicle information center (evic). Refer to “electronic vehicle information center” in “unders...

  • Page 269

    • vehicle identification number (vin) • type of vehicle • month day and hour of manufacture (mdh) the bar code allows a computer scanner to read the vin. Gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total ...

  • Page 270

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 271

    Have exceeded either gawr, but the total load is within the specified gvwr, you must redistribute the weight. Improper weight distribution can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Note: refer to the “vehicle certification label” affixed to...

  • Page 272

    The recommended way to measure gtw is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross axle weight rating (gawr) the gawr is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles ...

  • Page 273

    If equipped, the electronic trailer sway control (tsc) recognizes a swaying trailer and automatically applies individual wheel brakes and/or reduces engine power to attempt to eliminate the trailer sway. Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it ...

  • Page 274

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 275

    Trailer towing weights (maximum trailer weight ratings) note: for additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • ramtrucks.Com/en/towing_guide/ • ramtruck.Ca (canada) • rambodybuilder.Com trailer and tongue weight always load a tr...

  • Page 276

    Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weight of the driver and all passengers. Note: remember that everything put into or on the...

  • Page 277

    Perform the maintenance listed in the “maintenance schedule.” refer to “maintenance schedule” for the proper maintenance intervals. When towing a trailer, never exceed the gawr or gcwr ratings. Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as s...

  • Page 278

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized. Towing requirements — tires • do not attempt to tow a trailer while ...

  • Page 279

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • an electronically actuated trailer brake controller is required when towing a trailer w...

  • Page 280

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing requirements — trailer lights an...

  • Page 281

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 282

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic transmission the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. ...

  • Page 283

    Cooling system to reduce potential for engine and transmission over- heating, take the following actions: city driving when stopped for short periods, shift the transmission into neutral and increase engine idle speed. Highway driving reduce speed. Air conditioning turn off temporarily. Recreational...

  • Page 284

    Note: for vehicles equipped with diesel engine, see important information in the diesel supplement. Recreational towing — automatic transmission recreational towing is allowed only if the front wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow d...

  • Page 285

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .285 䡵 if your engine overheats . . . . . . . . . . . .285 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .286 ▫ torque specifications . . . . . . . . . . . . . . . . . . .287 䡵 tire se...

  • Page 286

    䡵 freeing a stuck vehicle . . . . . . . . . . . . .319 䡵 shift lever override . . . . . . . . . . . . . . . .320 䡵 towing a disabled vehicle . . . . . . . . . . .321 ▫ automatic transmission . . . . . . . . . . . . . . . .322 284 what to do in emergencies.

  • Page 287

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency....

  • Page 288

    Supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads hot (h), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer dr...

  • Page 289

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 145 ft-lbs (197 n·m) m16 x 1.50 21 mm **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the ...

  • Page 290

    After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has (continued) warning! (continued) been lowered. Fa...

  • Page 291

    Tire service kit components and operation using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black ai...

  • Page 292

    Using the deflation button push the deflation button (2) to reduce the air pressure in the tire if it becomes over-inflated. Tire service kit usage precautions • replace the tire service kit sealant bottle (1) and sealant hose (6) prior to the expiration date (printed at the lower right hand corner ...

  • Page 293

    From the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tire service kit. • you can use the tire service kit air pump to inflate...

  • Page 294

    Warning! (continued) • keep tire service kit away from open flames or heat source. • a loose tire service kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tire service kit in the place provided. Failure to follow these warn- ings can result ...

  • Page 295

    On the ground. This will provide the best positioning of the kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceeding. 3. Place the transmission in park (auto transmission) or in gear (man...

  • Page 296

    Note: sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 – 10 seconds through the sealant hose (6): 1. Push the power button (4) to turn off the tire service kit. Disconnect the sealant hose (6) from the valve stem. Make sure the valve stem is ...

  • Page 297

    Latch pillar (recommended pressure). Check the tire pressure by looking at the pressure gauge (3). If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tir...

  • Page 298

    (d) drive vehicle: immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the tire service kit sealant within the tire. Do not exceed 55 mph (90 km/h). Warning! Tire service kit is not a permanent flat tire repair. Have th...

  • Page 299

    Note: if the tire becomes over-inflated, push the defla- tion button to reduce the tire pressure to the recom- mended inflation pressure before continuing. 2. Disconnect the tire service kit from the valve stem, reinstall the cap on the valve stem and unplug from 12 volt outlet. 3. Place the tire se...

  • Page 300

    The front of the housing. Push the bottle into the housing. An audible click will be heard indicating the bottle is locked into place. 6. Verify that the cap is installed on the fitting at the end of the sealant hose (6) and return the hose to its storage area (located on the bottom of the air pump)...

  • Page 301

    Removing the spare tire 1. Remove the spare tire before attempting to jack up the vehicle. Attach the lug bolt adapter to the winch extension and insert it into the winch mechanism. Jack location jack tools 1 — winch extension 2 — lug bolt adapter 3 — wrench handle 6 what to do in emergencies 299.

  • Page 302

    The winch mechanism is located under the rear of the vehicle to the right of the spare tire. 2. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. Winch location winch extension 300 what to...

  • Page 303

    Note: the winch mechanism is designed for use with the winch extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. 3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. Lowering spare tire spare tire 6 what ...

  • Page 304

    4. Remove the retainer nut prior to removing the retainer from the wheel. 5. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. Retainer nut lifting spare tire 302 what to do in emergencies.

  • Page 305

    6. Pull the retainer through the center of the wheel. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit whe...

  • Page 306

    Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as pos...

  • Page 307

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Loosen (but do not remove) the wheel lug bolts by turning them to the left one turn while the wheel is still on the ground. 2. There are two jack engagemen...

  • Page 308

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated. Note: the rear jacking location is located in front of the rear tire and in front of the leaf spring mount. Note: the front jacking location is located behind the front tire and in front of the driver/pa...

  • Page 309

    Warning! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body (continued) warning! (continued) under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center...

  • Page 310

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel lug bolts. For vehicles with wheel covers, remove the cover from the wheel by hand. Do not p...

  • Page 311

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Note: do not install the wheel cover on the spare tire. 7. Lower the vehicle by turning the jack screw...

  • Page 312

    Caution! In the case that the yellow dot does not appear in the winch mechanism window refer to step 11 above, the (continued) caution! (continued) operator should repeat the spare tire instillation procedure. If the yellow dot does not appear in the winch indication window, place and secure the dam...

  • Page 313

    13. Check the spare tire pressure as soon as possible. Correct the tire pressure, as required. For vehicles with aluminum wheels: 1. Remove the adapter bracket and bolts from the storage bag in the glove compartment. 2. Take the retainer and position it inside the circular bracket. 3. Tighten the kn...

  • Page 314

    4. Position the tire vertically and lay the mounted adapter on the inner part of the rim. Using the supplied bolts, fasten the wheel to the adapter using the bolt install wrench. Tighten the bolts with the wrench extension and wrench handle. Securing the bracket alloy wheel mounting 312 what to do i...

  • Page 315

    5. Follow the steps above for proper spare tire stowage. Wheel covers caution! Use a back-and-forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap finish may occur. The wheel covers on the vehicle are held in place by the wheel lug bolts a...

  • Page 316

    Note: when using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electr...

  • Page 317

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 318

    3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-start...

  • Page 319

    4. Connect the opposite end of the negative (-) jumper cable to the remote negative (-) post of the discharged vehicle. Note: the remote negative (-) post is located in the front of the engine compartment on the driver’s side. Warning! Do not connect the jumper cable to the negative (-) post of the ...

  • Page 320

    If frequent jump-starting is required to start your vehicle you should have the battery and charging system in- spected at your authorized dealer. Caution! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Ev...

  • Page 321

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand, or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse , while gently pressing the accelerator. Us...

  • Page 322

    Note: push the ⬙ esc off ⬙ switch, to place the electronic stability control (esc) system in ⬙ partial off ⬙ mode, before rocking the vehicle. Refer to “electronic brake control system” in “starting and operating” for further information. Once the vehicle has been freed, push the ⬙ esc off ⬙ switch ...

  • Page 323

    3. Using a small screwdriver or similar tool, remove the shift lever override access cover which is located below the shift lever. 4. Press and maintain firm pressure on the brake pedal. 5. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever forw...

  • Page 324

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 325

    • the towing distance must not exceed 15 miles (24 km). If the transmission is not operable, or the vehicle must be towed faster than 25 mph (40 km/h) or farther than 15 miles (24 km), tow with the front wheels off the ground (using a flatbed truck, or wheel lift equipment with the front wheels rais...

  • Page 327

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . .327 䡵 onboard diagnostic system — obd ii . .328 ▫ loose fuel filler cap message . . . . . . . . . . . .328 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . .329 䡵 replacement parts . . . . . . . ....

  • Page 328

    ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .353 ▫ cleaning the instrument panel cupholders . .360 䡵 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .361 ▫ underhood fuses. . . . . . . . . . . . . . . . . . . . . .362 ▫ interior...

  • Page 329

    Engine compartment — 3.6l 1 — washer solvent reservoir 5 — power distribution center (fuses) 2 — engine oil fill 6 — coolant reservoir 3 — engine oil dipstick 7 — power steering reservoir 4 — brake fluid reservoir 7 maintaining your vehicle 327.

  • Page 330

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 331

    Tighten the gas cap until a ⬙ clicking ⬙ sound is heard. This is an indication that the gas cap is properly tightened. Push the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If ...

  • Page 332

    2. As soon as you cycle the ignition switch to the on position, you will see the malfunction indicator light (mil) symbol come on as part of a normal bulb check. 3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully...

  • Page 333

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 334

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 335

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for further informa- tion. Note: under no circumstances should oil change in- tervals exceed 10,000 miles (16,000 km) or twelve mon...

  • Page 336

    Engine oil viscosity — 3.6l engine mopar® sae 5w-20 engine oil approved to fca us material standard ms-6395 such as pennzoil®, shell helix® or equivalent is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler c...

  • Page 337

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 338

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 339

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 340

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 341

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 342

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) t...

  • Page 343

    2. Remove and replace the a/c air filter from the filter retainer. Accessing air filter 1 — screw locations 2 — fresh air inlet removing air filer 1 — fresh air inlet 2 — a/c air filter 3 — a/c air filter retainer 7 maintaining your vehicle 341.

  • Page 344

    3. Install the a/c air filter/filter retainer back into the fresh air inlet. When installing the filter retainer make sure the retainer is fully engaged. 4. Install the two screws back into the assembly to secure the filter retainer to the fresh air inlet. Body lubrication locks and all body pivot p...

  • Page 345

    Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may ...

  • Page 346

    Cooling system warning! • when working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at anytime the ignition switch is in the on position. • you or others can be badly burned by hot engine...

  • Page 347

    Refer to the “maintenance schedule” for the proper maintenance intervals. Selection of coolant refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oa...

  • Page 348

    Adding coolant your vehicle has been built with an improved engine coolant (oat coolant conforming to ms.90032) that al- lows extended maintenance intervals. This engine cool- ant (antifreeze) can be used up to ten years or 150,000 miles (240,000 km) before replacement. To prevent reduc- ing this ex...

  • Page 349

    Note: • some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. • mixing engine coolant (antifreeze) types is not r...

  • Page 350

    With your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance...

  • Page 351

    • if frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested for leaks. • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms.90032) and distilled water for proper corrosion protection of your engine w...

  • Page 352

    Master cylinder — brake fluid level check the fluid level in the master cylinder should be checked when performing underhood services, or immediately if the “brake system warning light” indicates system failure. Clean the top of the master cylinder area before removing the cap. Add fluid to bring th...

  • Page 353

    Warning! (continued) cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or pro- longed braking, resulting in sudden brake failure. This could result in a col...

  • Page 354

    Caution! (continued) in transmission shift quality and/or torque converter shudder, and will require more frequent fluid and filter changes. Refer to “fluids, lubricants, and genuine parts” in this section for fluid specifica- tions. Special additives the manufacturer strongly recommends against usi...

  • Page 355

    Caution! If a transmission fluid leak occurs, visit your autho- rized dealer immediately. Severe transmission dam- age may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid and filter changes refer to the “maintenance schedule” for the proper maintenance ...

  • Page 356

    • insects, tree sap and tar. • salt in the air near seacoast localities. • atmospheric fallout/industrial pollutants. Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar® car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if ...

  • Page 357

    • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • if you carry special cargo such as chemicals, fertilizers, de-ice...

  • Page 358

    Caution! Avoid products or automatic car washes that use acidic solutions or strong alkaline additives or harsh brushes. These products and automatic car washes may damage the wheel’s protective finish. Such damage is not covered by the new vehicle limited warranty. Only car wash soap, mopar wheel c...

  • Page 359

    Dark vapor or black satin chrome wheels caution! If your vehicle is equipped with dark vapor or black satin chrome wheels do not use wheel cleaners, abrasives or polishing compounds. They will perma- nently damage this finish and such damage is not covered by the new vehicle limited warranty. Use on...

  • Page 360

    Cleaning interior trim interior trim should be cleaned starting with a damp cloth, a damp cloth with mopar® total clean or equiva- lent, then mopar® spot & stain remover or equivalent if absolutely necessary. Do not use harsh cleaners or armor all®. Use mopar® total clean or equivalent to clean viny...

  • Page 361

    Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do...

  • Page 362

    If the belts need cleaning, use mopar® total clean, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. Dry with a soft cloth. Replace the belts if they appear frayed or worn or if the buckles do not work properly. Warning! A frayed or torn belt could rip ...

  • Page 363

    Installation place the liner into the cupholder drawer and push the liner into place so that the retention tabs seat into the corresponding openings in the drawer. Fuses warning! • when replacing a blown fuse, always use an ap- propriate replacement fuse with the same amp rating as the original fuse...

  • Page 364

    Underhood fuses the front power distribution center is located on the driver’s side of the engine compartment. To access the fuses, remove the cover. The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Front power distribution center 362 main...

  • Page 365

    Cavity maxi fuse mini fuse description f01 40 amp orange electronic stability control (esc) pump f02 20 amp yellow (3.6 gasoline engine) starter relay 3.6l (3.6 gasoline engine) f02 50 amp red (3.0 diesel engine) glow plug unit (3.0 diesel engine) f04 50 amp red (3.6 gasoline engine) secondary power...

  • Page 366

    Cavity maxi fuse mini fuse description f07 50 amp red (non a/c) 60 amp blue (a/c) engine cooling fan - 1st speed f08 40 amp orange passenger compartment blower f09 15 amp blue rear power outlet f10 15 amp blue horn f11 15 amp blue fuel pressure regulator (mprop)-drv (3.0 diesel engine) — if equipped...

  • Page 367

    Cavity maxi fuse mini fuse description f17 20 amp yellow engine control module (ecm), injectors (3.6 gasoline engine) f17 20 amp yellow secondary loads, engine control module (ecm) (3.0 diesel engine) f18 7.5 amp brown kl30 engine control module (ecm), kl30 main relay coil (3.6 gasoline engine) f18 ...

  • Page 368

    Cavity maxi fuse mini fuse description f23 20 amp yellow electronic stability control (esc) valves f24 7.5 amp brown kl15 vacuum pump relay coil (3.6 gasoline en- gine) — if equipped f30 15 amp blue heated mirrors front pdc additional fuses the additional fuse box is located inside the front pdc box...

  • Page 369

    Cavity mini fuse description f61 20 amp yellow vacuum pump (3.6 gasoline engine) — if equipped f62 30 amp green transmission power rele (3.6 gasoline engine) — if equipped f64 7.5 amp brown urea pump (3.0 diesel engine) — if equipped f65 25 amp white urea nox sensor 1–2 — pm sensor (3.0 diesel en- g...

  • Page 370

    Interior fuses the interior fuse panel is part of the body control module (bcm) and is located on the driver’s side under the instrument panel. Fuse panel 368 maintaining your vehicle.

  • Page 371

    Fuse panel cavity locations 7 maintaining your vehicle 369.

  • Page 372

    Cavity mini fuse description f12 10 amp red right low beam f13 10 amp red left low beam f31 5 amp beige int/a f32 10 amp red sbmt f34 7.5 amp brown clearance lights f36 15 amp blue +30 (acm – tpcu – rrm – dlc) f37 5 amp beige int (brake no – ipc) f38 15 amp blue central locking f42 5 amp beige int (...

  • Page 373

    Cavity mini fuse description f50 7.5 amp brown int (orc) f51 5 amp beige int (rear camera-aux) f53 5 amp beige +30 (ipc) f90 7.5 amp brown left high beam f91 7.5 amp brown right high beam f92 7.5 amp brown left fog lamp f93 7.5 amp brown right fog lamp 7 maintaining your vehicle 371.

  • Page 374

    Right central pillar fuses the right central pillar fuse panel is located on the interior side at the base of the passenger side b pillar. Fuse panel location fuse panel 372 maintaining your vehicle.

  • Page 375

    Cavity mini fuse description f81 7.5 amp brown seat heater f83 20 amp yellow rear left windows heater f84 20 amp yellow rear right windows heater vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • disconnect the ...

  • Page 376

    Replacement bulbs interior bulbs bulb number overhead lamp c5w sun visors c5w courtesy lamp ff500 glove compartment c5w rear courtesy lamp c5w exterior bulbs bulb number front low and high beam headlamp h7ll front park/turn signal lamps 7444na daytime running lamps (if equipped) 7440 front side mark...

  • Page 377

    Bulb number rear turn signal lamps 7440na rear backup lamps 921 rear side marker lamps w3w front fog lamps h11 license plate lamps c5w front roof lamps wy5w rear roof lamps w3w note: • numbers refer to commercial bulb types that can be purchased from your authorized dealer. • if a bulb needs to be r...

  • Page 378

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamps low beam and high beam no...

  • Page 379

    16. Carefully reinstall screw (1) on lower headlamp filler panel. 17. Carefully reinstall screws (2) on upper headlamp filler panel. Front turn signal/parking lamps note: passenger side headlamp must be removed for bulb replacement, for driver side headlamp go to step 6 through step 7. 1. Remove scr...

  • Page 380

    Daytime running lamp (drl)/front side marker lamp note: passenger side headlamp must be removed for bulb replacement, for driver side headlamp go to step 6 through step 8. 1. Remove screw (1) on lower headlamp filler panel. 2. Remove screws (2) on upper headlamp filler panel. 3. Remove upper screw (...

  • Page 381

    Front fog lamps 1. Turn front wheels inboard to access cover in wheel liner. 2. Open the cover on the front of the wheel liner. 3. Remove connection and replace the bulb. 4. Connect the wire and rotate bulb/socket clockwise into lamp locking it in place. 5. Reinstall the plastic cap and close the co...

  • Page 382

    Fluid capacities u.S. Metric fuel (approximate) 24 gallons 90 liters engine oil with filter 3.6l engine (sae 5w-20, api certi- fied) 6 quarts 5.6 liters cooling system * 3.6l engine (mopar® antifreeze/ engine coolant 10 year/150,000 mile formula or equivalent) 10.5 quarts 10 liters 380 maintaining y...

  • Page 383

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) meeting the requirements of fca material standard ms.90032. Engine oil we recommend yo...

  • Page 384

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 385

    Chassis component fluid, lubricant, or genuine part automatic transmission – 3.6l gasoline engine only use only atf+4® automatic transmission fluid. Fail- ure to use atf+4® fluid may affect the function or performance of your transmission. We recommend mopar® atf+4® fluid. Brake master cylinder we r...

  • Page 387

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .386 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .387 8.

  • Page 388

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate in th...

  • Page 389

    Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire inflation pressures and look for unusual wear or damage • check the fluid levels of the coolant reservoir, brake master cylinder, and power steering and fill as needed • check function...

  • Page 390

    Refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kil...

  • Page 391

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 392

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 393

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .393 ▫ prepare for the appointment. . . . . . . . . . . . .393 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .393 ▫ be reasonable with requests ....

  • Page 394

    䡵 publication order forms . . . . . . . . . . . .398 䡵 department of transportation uniform tire quality grades . . . . . . . .399 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .399 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .399 ▫ temperature grades. . . . . . . ...

  • Page 395

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 396

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 397

    In mexico contact av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has instal...

  • Page 398

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 399

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 400

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 401

    Call toll free at: • 1-800-890-4038 (u.S.) • 1-800-387-1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 402

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 403

    Index 10

  • Page 404

    Adding engine coolant (antifreeze) . . . . . . . . . . . .346 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .264 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .343 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .262 air bag . . . . . . . . ....

  • Page 405

    Fluid type . . . . . . . . . . . . . . . . . . . . . . . . .351, 383 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . .205 special additives . . . . . . . . . . . . . . . . . . . . . . .352 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .338 keyless transmitte...

  • Page 406

    Checking your vehicle for safety . . . . . . . . . . . . . . .65 checks, safety . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 child restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 child restraints booster seats . . . . . . . . . . . . . . . . . . . . . . . . . . .58 c...

  • Page 407

    Defroster, windshield . . . . . . . . . . . . . . . . . . . .67, 186 diagnostic system, onboard . . . . . . . . . . . . . . . . .328 dimmer control . . . . . . . . . . . . . . . . . . . . . . . . . . .94 dimmer switch, headlight . . . . . . . . . . . . . . . . . . .96 dipsticks automatic transmissio...

  • Page 408

    Compartment identification . . . . . . . . . . . . . . . .327 coolant (antifreeze) . . . . . . . . . . . . . . . . . .344, 381 cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .344 exhaust gas caution . . . . . . . . . . . . . . . . . . . . .66 fails to start . . . . . . . . . . . ....

  • Page 409

    Cooling system . . . . . . . . . . . . . . . . . . . . . . . . .344 power steering . . . . . . . . . . . . . . . . . . . . . . . . .217 fluids, lubricants and genuine parts . . . . . . . . . . .381 fog lights. . . . . . . . . . . . . . . . . . . . . . . . . . . .95, 128 four-way hazard flasher . . ....

  • Page 410

    Gross vehicle weight rating . . . . . . . . . . . . . .267, 269 guide, body builders . . . . . . . . . . . . . . . . . . . . . . . .6 gvwr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267 hazard driving through flowing, rising, or shallow standing water . . . . . . . . . . . . . ...

  • Page 411

    Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . .313 key-in reminder . . . . . . . . . . . . . . . . . . . . . . . . . .13 key, replacement . . . . . . . . . . . . . . . . . . . . . . . . . .14 keys . . . ....

  • Page 412

    Oil pressure . . . . . . . . . . . . . . . . . . . . . . . . . . .128 park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 seat belt reminder . . . . . . . . . . . . . . . . . . . . . .128 service . . . . . ....

  • Page 413

    New vehicle break-in period . . . . . . . . . . . . . . . . . .64 occupant restraints . . . . . . . . . . . . . . . . . . . . . . . .24 octane rating, gasoline (fuel) . . . . . . . . . . . . . . . .260 odometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 trip . . . . . . . . . . ...

  • Page 414

    Steering . . . . . . . . . . . . . . . . . . . . . . . . . . .216, 217 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 power steering fluid . . . . . . . . . . . . . . . . . . . . . . .383 pregnant women and seat belts . . . . . . . . . . . . . . .35 pretensioners seat belts . ...

  • Page 415

    Automatic locking retractor (alr) . . . . . . . . . . .36 energy management feature . . . . . . . . . . . . . . . .36 lap/shoulder belt operation . . . . . . . . . . . . . . . .30 lap/shoulder belts . . . . . . . . . . . . . . . . . . . . . . .27 lap/shoulder belt untwisting . . . . . . . . . . . . ...

  • Page 416

    Snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .245 spare tire . . . . . . . . . . . . . . . . . . . . . . . . . . .246, 248 spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .381 speed control (cruise control). . . . . . . . . . . . . . . .102 speedometer. . ...

  • Page 417

    Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .243 replacement . . . . . . . . . . . . . . . . . . . . . . . . . . .250 rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253 safety . . . . . . . . . . . . . . . . . . . . . . . . . . . .230, 240 sizes . . . . . ...

  • Page 418

    Transporting pets . . . . . . . . . . . . . . . . . . . . . . . . . .63 tread wear indicators . . . . . . . . . . . . . . . . . . . . . .249 trip odometer . . . . . . . . . . . . . . . . . . . . . . . . . . .128 turn signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 uniform tire q...

  • Page 419

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 420

    P r o m a s t e r o w n e r ’ s m a n u a l 2 0 1 5 2015 promaster 15vf-126-af sixth edition printed in u.S.A. Fca us llc.