1. DL manuals
  2. RAM
  3. Automobile
  4. PROMASTER CITY2018
  5. Owner's Manual

RAM PROMASTER CITY2018 Owner's Manual

Summary of PROMASTER CITY2018

  • Page 1

    Second edition printed in the u.S.A. ©2017 fca us llc. All rights reserved. Ram is a registered trademark of fca us llc. 18vm-126-ab p r o m a s t e r c i t y o w n e r ’ s m a n u a l 2 0 1 8 promaster cit y 2018.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 graphical table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . . .5 ▫ essential information . . . . . . . . . . . . . . . . . . . . . .5 ▫ symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 䡵 warnings and...

  • Page 6

    Introduction dear customer, congratulations on selecting your new vehicle. Be assured that it represents precision workmanship, distinctive styl- ing, and high quality. This owner’s manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation...

  • Page 7

    How to use this manual essential information consult the table of contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustra- tions may differ from your vehicle’s equipm...

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may mi...

  • Page 9: Contents

    Graphical table of contents contents 䡵 front view . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 䡵 rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 䡵 instrument panel . . . . . . . . . . . . . . . . . . . . .10 䡵 interior . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 10

    Front view front view 1 — hood/engine compartment 4 — wheels/tires 2 — windshield 5 — exterior mirrors 3 — headlights 6 — doors 8 graphical table of contents.

  • Page 11

    Rear view rear view 1 — rear lights 2 — cargo area doors 2 graphical table of contents 9.

  • Page 12

    Instrument panel instrument panel 1 — air vents 4 — windshield wiper lever 2 — multifunction lever 5 — radio 3 — instrument cluster 6 — steering wheel 10 graphical table of contents.

  • Page 13

    Interior interior 1 — door locks/window switches 4 — climate controls 2 — seats 5 — switch panel 3 — gear selector 6 — glove compartment 2 graphical table of contents 11.

  • Page 15: Contents

    Getting to know your vehicle contents 䡵 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 䡵 ignition switch . . . . . . . . . . . . . . . . . . . . . . .19 ▫ ignition key removal . . . . . . . . . . . . . ...

  • Page 16

    ▫ tilt/telescoping steering column . . . . . . . . . . . .37 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ▫ inside day/night mirror — if equipped . . . . . .38 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . . .38 ▫ power outside mirrors — if equipped . . . ....

  • Page 17

    ▫ rear cargo tie-downs . . . . . . . . . . . . . . . . . . .62 䡵 internal equipment . . . . . . . . . . . . . . . . . . .63 ▫ storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 ▫ cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . .65 ▫ power outlets . . . . . . . . ....

  • Page 18

    Keys key fob your vehicle uses a key start ignition system. The ignition system consists of a key fob with a remote keyless entry (rke) and an ignition switch. The key fob contains an integrated mechanical key. To use the mechanical key, simply push the mechanical key re- lease button. The vehicle i...

  • Page 19

    Remote keyless entry (rke) this system allows you to lock or unlock the doors from distances up to approximately 66 ft (20 m) using a hand- held key fob. The key fob does not need to be pointed at the vehicle to activate the system. Note: the key fob may not be able to be detected by the vehicle if ...

  • Page 20

    If a door is open, the turn signal lights will flash at an increased rate, and there will be no horn chirp. This is to indicate that a door is still open. Locking doors with a key 1. Insert the key with either side up. 2. Turn the key to the right to lock the door. 3. Turn the key to the left to unl...

  • Page 21

    Programming additional key fobs programming the key fob may be performed by your authorized dealer. General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada...

  • Page 22

    Warning! • before exiting a vehicle, always shift the transmis- sion into park, apply the parking brake, and re- move the key fob from the vehicle. When leaving the vehicle, always lock your vehicle. In case you switch off the vehicle and the transmission is not in park position, a warning message w...

  • Page 23

    The system uses ignition keys which have an embedded electronic chip (transponder) to prevent unauthorized ve- hicle operation. Therefore, only keys that are programmed to the vehicle can be used to start and operate the vehicle. Note: a key which has not been programmed is also considered an invali...

  • Page 24

    Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Vehicle security alarm — if equipped the vehicle security alarm monitors the vehicle doors and ignition for unauthorized operation. When the vehicle...

  • Page 25

    Doors door locks the door locks can be locked or unlocked from inside the vehicle by using the door handle. • to lock the doors, push down on the door handle. • to unlock the doors, pull up on the door handle. Locking the doors from the outside follow the below methods to lock the vehicle from the o...

  • Page 26

    Locking with the key blade push the key blade release button to expose the key blade, insert the key blade into the doors exterior lock cylinder and turn the key clockwise to lock the front door. Unlock the doors from the outside follow the below methods to unlock the vehicle from the outside: unloc...

  • Page 27

    Unlocking with the key blade push the key blade release button to expose the key blade, insert the key blade into the driver door exterior lock cylinder and turn the key counterclockwise to unlock the all doors. Unlocking the rear cargo area from inside the vehicle pull up on the lock/unlock lever l...

  • Page 28

    Sliding side door on cargo versions, the sliding side door is fitted with a spring-loaded latch that stops the door from opening any further. To lock it, simply push the door as far as it will go; to unlock it, pull forward firmly. Opening and closing from outside the vehicle opening/unlocking with ...

  • Page 29

    Closing: pull the interior door handle switch to release the door and then push it towards the front of the vehicle. Key emergency lock (kel) device the sliding side doors are provided with a device for locking all the doors using the lock in case of a power fault. The device can be engaged with the...

  • Page 30

    Child lock system this system prevents the sliding side doors being opened from the inside. The child locks can only be engaged/disengaged with the sliding side door open: to engage or disengage the child-protection door lock system 1. Open the rear door. 2. Insert the tip of the emergency key into ...

  • Page 31

    Double rear swing doors the rear double swing doors are fitted through a fastening system which stops them when they reach an opening angle of approximately 90 degrees. To open them wider to an angle of 180 degrees, push the locking device (one on each side) and simultaneously open the doors. Using ...

  • Page 32

    Manual adjustment (front seats) the front driver and passenger seats can be adjusted forward and rearward, and if equipped, may be reclined and the height and lumbar can be adjusted. Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of contr...

  • Page 33

    Forward and rearward adjustment the adjustment bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the sea...

  • Page 34

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the lower outboard side of the seat. Push the switch once to turn on the heated seats. The led ...

  • Page 35

    Folding rear seat — if equipped to provide additional storage area, each rear seat can be folded flat to allow for extended cargo space. 1. Locate the release lever (upper outboard side of seat), and lift it upward until the seatback releases. 2. Slowly fold down the seatback. 3. Pull forward on the...

  • Page 36

    4. Reverse order for original setting. Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! • all o...

  • Page 37

    Front adjustment to raise the head restraint, push the adjustment button, located on the base of the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment button, located on the base of the head re- straint, and push downward on the head restraint. Rear ...

  • Page 38

    Warning! A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow removed head re- straints in a location outside the occupant compartment. Front removal to remove the head restraint, raise it as far as it...

  • Page 39

    Center head restraint to remove the head restraint, push the release button and adjustment button while pulling upward on the whole assembly and raise it as far as it can go. To reinstall the headrest, put the headrest posts into the holes while pushing the release button and adjustment button. Then...

  • Page 40

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Mirrors inside day/night ...

  • Page 41

    Warning! (continued) could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in a side convex mirror. Manual outside mirror adjustment — if equipped from the inside of the vehicle, use the control lever to adjust the...

  • Page 42

    Power outside mirrors — if equipped the power mirror controls are located on the mirror flag trim above the driver’s door trim panel. To adjust a mirror, turn the control knob toward the left or right mirror positions indicated. Tilt the control knob in the direction you want the mirror to move. Whe...

  • Page 43

    Sun visor “slide-on-rod” feature — if equipped the sun visor “slide-on-rod” feature allows for additional flexibility in positioning the sun visor to block out the sun. 1. Fold down the sun visor. 2. Unclip the visor from the center clip. 3. Pull the sun visor toward the inside rearview mirror to ex...

  • Page 44

    Daytime running lights — if equipped to activate the daytime running lights (drl), rotate the end of the multifunction lever to the o symbol. Note: • the low beams and side/tail lights will not be on with drl. The drl function may be programmed to be on or off through the uconnect system screen. Ref...

  • Page 45

    Front fog lights — if equipped the fog light switch is located on the center stack of the instrument panel, just below the radio. Push the switch once to turn the front fog lights on. Push the switch a second time to turn the front fog lights off. Turn signals move the multifunction lever up or down...

  • Page 46

    Right switch • push the right switch to the left to turn on the left map light. • push the right switch to the right to turn on the right map light. Rear lights cargo vehicle lateral roof light this is located on the right side of the load compartment. Rear roof light this is located on the rear pan...

  • Page 47

    In auto-mode the light comes on automatically when you open the sliding doors and the rear wing doors and goes out when you close them. • push the left-hand side of the lens to switch the light off when the doors are open. • push the right hand side of the lens to switch the light on when the doors ...

  • Page 48

    Second row seating and rear roof lights operation in auto-mode, the light comes on automatically when you open the sliding doors and the rear wing doors and goes out when you close them. • push the left-hand side of the lens to switch the light off when the doors are open. • push the right-hand side...

  • Page 49

    Cargo compartment light — if equipped the cargo compartment light comes on automatically when the swing doors are opened and turns off when the doors are closed. Wipers and washers the windshield wiper/washer lever is located on the right side of the steering column. Note: the windshield wipers/wash...

  • Page 50

    High speed rotate the end of the lever upward to the third detent. The wipers will operate at high speed. Intermittent wiper system rotate the end of the lever upward to the first detent. The wipers will operate at intermittent speed. When the vehicle’s speed increases, the time be- tween the wipes ...

  • Page 51

    • in synchronous mode (at half the speed of the front window wiper) when the front window wiper is oper- ating. • in continuous mode while vehicle is in reverse. With the windshield wipers on, and reverse gear en- gaged, rear window wiping will be continuous in the same way. Rear windshield washer o...

  • Page 52

    Manual climate control descriptions icon description a/c button push the a/c button to engage the air conditioning (a/c). A led will illuminate when the a/c system is engaged. The a/c can be deselected manually without disturbing the mode con- trol selection. Recirculation button press and release t...

  • Page 53

    Icon description rear defrost button push and release the rear defrost control button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window de- froster is on. The rear window defroster automatically turns off after 20 min...

  • Page 54

    Icon description bi-level mode bi-level mode air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Note: bi-level mode is designed under comfort conditions to provide cooler air out of the panel out- le...

  • Page 55

    System maintenance in winter, the climate control system must be turned on at least once a month for about ten minutes. Have the system inspected at an authorized dealer before the summer. Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the...

  • Page 56

    Recirculation when outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by pressing the recirculation control button. The recirculation indicator will illuminate when this button is selected. Press the button a second time to t...

  • Page 57

    Outside air intake make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves. Leaves collected in the air intake may reduce airflow, can cause odor, and if they enter the plenum they could plug the water drains. In winter months make sure the air i...

  • Page 58

    Control setting suggestions for various weather conditions control settings suggestions for various weather conditions chart 56 getting to know your vehicle.

  • Page 59

    Windows power windows — if equipped the control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control. If the vehicle is equipped with rear power wi...

  • Page 60

    Warning! (continued) • do not leave the key fob in or near the vehicle or in a location accessible to children. A child could oper- ate power windows, other controls, or move the vehicle. Auto-down feature — if equipped the window switches are equipped with an auto-down feature. Push the window swit...

  • Page 61

    • fuse or battery are disconnected when the window is moving. • the auto-revese system is activated while the window is moving and the door is opening. • 50 window movements without ever closing the win- dow. • one door opening movements with the window mov- ing, without ever closing the door. • thr...

  • Page 62

    Normal occurrence and can be minimized. If the buffeting occurs open the front windows together to minimize the buffeting. Hood opening to open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door. 2. Move to the outsi...

  • Page 63

    3. Raise the hood and place the hood prop rod in hood slot to secure the hood in the open position. Caution! Be sure to disengage the rod and secure it in close position before closing the hood. Damage may occur. Closing warning! Be sure the hood is fully latched before driving your vehicle. If the ...

  • Page 64

    Cargo area features rear cargo tie-downs to make it easier to secure your load, there are hooks (if equipped) fixed to the floor. Note: power washing is not allowed inside the cargo area. Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area. The ...

  • Page 65

    Warning! (continued) • cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or accident, a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. The weight and position ...

  • Page 66

    Note: the glove compartment handle is equipped with a lock. To lock the glove compartment, remove the emer- gency key from the key fob, insert emergency key into glove compartment handle lock cylinder and turn the key to the lock position and remove the key. Use the reverse sequence to unlock the gl...

  • Page 67

    Overhead console storage there is additional shelf storage above the front sun visors. Cupholders a cupholder is located in the front and rear of the center console. Power outlets passenger compartment power outlets the cigar lighter and the power socket are located in the center console, and both o...

  • Page 68

    Load compartment power outlet the load compartment power outlet is located on the left side of the rear cargo compartment. It operates with the ignition key in the mar (acc/on/run) position. The outlet can be used for powering 12 volt adaptive accesso- ries and recharging communications devices. Cau...

  • Page 69

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 70

    Roof rack — if equipped the crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Note: if not equipped with crossbars, your authorized dealer c...

  • Page 71

    Caution! • to prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without the crossbars deployed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or other protec...

  • Page 73: Contents

    Getting to know your instrument panel contents 䡵 instrument cluster . . . . . . . . . . . . . . . . . . .72 ▫ instrument cluster descriptions . . . . . . . . . . . . .72 䡵 instrument cluster display . . . . . . . . . . . .73 ▫ location and controls . . . . . . . . . . . . . . . . . . .74 ▫ change en...

  • Page 74

    Instrument cluster instrument cluster descriptions 1. Speedometer • indicates vehicle speed. 2. Fuel gauge • the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. • the fuel pump arrow symbol points to the side of the vehicle where the fuel door is ...

  • Page 75

    3. Temperature gauge • the temperature gauge shows engine coolant tem- perature. Any reading within the normal range indi- cates that the engine cooling system is operating satisfactorily. • the gauge pointer will likely indicate a higher tem- perature when driving in hot weather or up mountain grad...

  • Page 76

    Cluster display is designed to display important informa- tion about your vehicle’s systems and features. Using a driver interactive display located on the instrument panel, your instrument cluster display can show you how sys- tems are working and give you warnings when they are not. The steering w...

  • Page 77

    • language • buzzer volume • belt buzzer • day lights the system allows the driver to select information by pushing the following buttons mounted on the instrument panel to the right of the steering column: • menu button push and release the menu button for a time longer than one second to access/se...

  • Page 78

    2. Push and release the up or down arrow button (by single pushes) to scroll through all the submenu options. 3. Briefly push and release the menu button to select the displayed submenu option and to open the relevant setup menu. 4. Push and release the up or down arrow button (by single pushes) to ...

  • Page 79

    2. If the function is on, push and release the up or down arrow button to select the required speed limit and then push menu to confirm. Note: the speed may be set in the range from 20 to 125 mph (30 to 200 km/h) according to the previously chosen unit. The setting will increase/decrease by five uni...

  • Page 80

    3. Select the required option and then push menu. 4. If selecting the “time” submenu, briefly push menu, the “hours” will flash on the display. 5. Push and release the up or down arrow button to adjust. 6. Push the menu button; the “minutes” will flash on the display. 7. Push and release the up or d...

  • Page 81

    The setting will increase or decrease by one unit each time the up or down arrow button is pushed. Hold down the up or down arrow button to increase/decrease the setting rapidly and automatically. Complete the adjustment when you approach the desired value. Push the menu button briefly to return to ...

  • Page 82

    1. If the set distance unit of measurement is ⬙mi⬙ (km) the fuel consumption unit will be displayed in ⬙mpg⬙ (km/l or l/100 km). 2. Push and release the up or down arrow button to select. When you select the ⬙temperature⬙ submenu: briefly push- ing the menu button the display will show ⬙°c⬙ or ⬙°f⬙ ...

  • Page 83

    Exit menu this is the last function that closes the cycle of settings listed in the menu screen. 1. Pushing the menu button briefly will return the dis- play to the standard screen without storing. 2. Push the down arrow button to return to the first menu item on the display. Trip computer the trip ...

  • Page 84

    2. Briefly push and release the menu button to go back to the menu screen or push and hold the menu (approxi- mately one second) to go back to the main screen without storing settings. Trip functions both trip functions are resettable (reset — start of new trip). “trip a” can be used to display the ...

  • Page 85

    Travel distance this value shows the distance covered since the last reset. Average fuel consumption this value shows the approximate average consumption since the last reset. Current fuel consumption this indicates the fuel consumption. The value is con- stantly updated. The message “----” will app...

  • Page 86

    Brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master c...

  • Page 87

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run position. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. — battery charge warning light this light illuminates when the battery is no...

  • Page 88

    The transmission into neutral and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if your engine overheats” in “in case of emergency” for further information. — oil pressure warning light this light indicates low...

  • Page 89

    — transmission fault warning light this light will illuminate (together with a message in the instrument cluster display and a buzzer) to indicate a transmission fault. Contact your authorized dealer if the message remains after restarting the engine. — engine oil level warning light this warning li...

  • Page 90

    — tire pressure monitoring system (tpms) warning light the warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recom- mended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be ...

  • Page 91

    Minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur f...

  • Page 92

    Several typical driving styles. In most situations, the ve- hicle will drive normally and will not require towing. When the engine is running, the mil may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced...

  • Page 93

    — electronic stability control (esc) off warning light — if equipped this light indicates the electronic stability control (esc) is off. Each time the ignition is turned to on/run or acc/on/ run, the esc system will be on, even if it was turned off previously. Yellow indicator lights — cold start in...

  • Page 94

    — cruise control set indicator light — if equipped this light will turn on when the speed control is set to the desired speed. Refer to “speed control” in “starting and operating” for further information. Blue indicator lights — high beam indicator light this indicator shows that the high beam headl...

  • Page 95

    Warning! • only an authorized service technician should con- nect equipment to the obd ii connection port in order to diagnose or service your vehicle. • if unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: • be possible that vehicl...

  • Page 96

    2. As soon as you cycle the ignition switch to the on position, you will see the “malfunction indicator light (mil)” symbol come on as part of a normal bulb check. 3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about ten seconds and then return to being fu...

  • Page 97: Safety

    Safety contents 䡵 safety features . . . . . . . . . . . . . . . . . . . . . . .96 ▫ four-wheel anti-lock brake system (abs) . . . . .96 ▫ electronic brake control system . . . . . . . . . . . . .97 䡵 auxiliary driving systems . . . . . . . . . . . . .101 ▫ tire pressure monitoring system (tpms) . . ...

  • Page 98

    Safety features four-wheel anti-lock brake system (abs) the four-wheel abs is designed to aid the driver in maintaining vehicle control under adverse braking condi- tions. The system operates with a separate computer to modulate hydraulic pressure, to prevent wheel lock-up and to help avoid skidding...

  • Page 99

    When you are in a severe braking condition involving the use of the abs, you will experience some pedal drop as the vehicle comes to a stop. This is the result of the system reverting to the base brake system. Engagement of the abs may be accompanied by a pulsing sensation. You may also hear a click...

  • Page 100

    And engine power is reduced to provide enhanced accel- eration and stability. A feature of the tcs system, brake limited differential (bld), functions similar to a limited slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the ot...

  • Page 101

    Electronic stability control (esc) the electronic stability control (esc) enhances directional control and stability of the vehicle under various driving conditions. Esc corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over...

  • Page 102

    Warning! (continued) increase the risk of loss of vehicle control, vehicle rollover, personal injury and death. Esc activation/malfunction indicator light and esc off indicator light the esc activation/malfunction indicator light in the instrument cluster will come on when the ignition switch is tur...

  • Page 103

    Erm can only reduce the chance of wheel lift occurring during severe or evasive driving maneuvers; it cannot prevent wheel lift due to other factors, such as road conditions, leaving the roadway, or striking objects or other vehicles. Warning! Many factors, such as vehicle loading, road conditions a...

  • Page 104

    Outside temperature decreases, the tire pressure will de- crease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour peri...

  • Page 105

    Caution! (continued) warning have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. • using aftermarket...

  • Page 106

    Note: it is particularly important for you to check the tire pressure in all of the tires on your vehicle regularly and to maintain the proper pressure. The tpms consists of the following components: • receiver module. • four tire pressure monitoring sensors. • tire pressure monitoring telltale ligh...

  • Page 107

    1. Tire service kit (original tire sealant – if equipped): after fixing the punctured tire with original tire sealant, the original situation will be restored, so system will turn off the telltale during the normal drive. 2. Compact spare tire – if equipped: the compact spare wheel is not equipped w...

  • Page 108

    Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: occupant restraint systems • seat belt systems • supplemental restraint systems (srs) air bags • child restraints some of the safety features described in this section may be standard equ...

  • Page 109

    Bags will inflate forcefully into the space between occu- pants and the door and occupants could be injured. 9. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, refer to “customer assistance” for customer service contact information. Warning! • never place...

  • Page 110

    Beltalert warning sequence the beltalert warning sequence is activated when the vehicle is moving above a specified vehicle speed range and the driver or outboard front seat passenger is unbuck- led (if equipped with outboard front passenger seat beltalert) (the outboard front passenger seat beltale...

  • Page 111

    The seat belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoulder part of the seat belt to move freely with you under normal conditions. However, in a collision the seat belt will lock and reduce your risk of striking the inside of the vehicle or...

  • Page 112

    Warning! • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not protect you pro...

  • Page 113

    Equipped with a rear seat). Grasp the latch plate and pull out the seat belt. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Positi...

  • Page 114

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automatically ...

  • Page 115

    Adjustable upper shoulder belt anchorage in the driver and front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck. Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that ...

  • Page 116

    Warning! (continued) internal injuries, or you could even slide out of the seat belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and n...

  • Page 117

    Seat belt pretensioner the front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision. Pretensione...

  • Page 118

    Vehicle with rear seat the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) which is used to secure a child restraint system. For additional information, refer to “installing child restraints using the vehicle seat belt” under the “child ...

  • Page 119

    How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire seat belt is extracted. 3. Allow the seat belt to retract. As the seat belt retracts, you will hear a clicking sound. This indicates the seat bel...

  • Page 120

    • steering wheel and column • instrument panel • knee impact bolsters • driver and front passenger air bags • seat belt buckle switch • supplemental side air bags • supplemental knee air bags • front and side impact sensors • seat belt pretensioners air bag warning light the orc monitors the readine...

  • Page 121

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. In this condition the air bags may not be ready to inflate for your protection. Have an authorized dealer service the air bag system immediately. Warning!...

  • Page 122

    Warning! (continued) • never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint. • only use a rear-facing child restraint in a vehicle wit...

  • Page 123

    Rollover collisions. The front air bags will not deploy in all frontal collisions, including some that may produce sub- stantial vehicle damage — for example, some pole colli- sions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, front...

  • Page 124

    Supplemental seat-mounted side air bags (sabs) are located in the outboard side of the front seats. The sabs are marked with a “srs airbag” or “airbag” label sewn into the outboard side of the seats. The sabs may help to reduce the risk of occupant injury during certain side impacts, in addition to ...

  • Page 125

    Supplemental side air bag inflatable curtains (sabics) are located above the side windows. The trim covering the sabics is labeled “srs airbag” or “airbag.” sabics may help reduce the risk of head and other injuries to front and rear seat outboard occupants in certain side impacts, in addition to th...

  • Page 126

    Side impacts the side air bags are designed to activate in certain side impacts. The occupant restraint controller (orc) deter- mines whether the deployment of the side air bags in a particular impact event is appropriate, based on the sever- ity and type of collision. The side impact sensors aid th...

  • Page 127

    Warning! • side air bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • being too close to the side air bags during deploy- ment could cause you to be severely injured or killed. • relying on the side air bags alone could lead to more severe in...

  • Page 128

    • supplemental side air bags • supplemental knee air bags • front and side impact sensors • seat belt pretensioners if a deployment occurs the front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean s...

  • Page 129

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • after any collision, the vehicle should be taken to an authorized dealer immediately. Enhanced accident response system in the event of an impact, if the communication network remains inta...

  • Page 130

    Warning! (continued) • it is dangerous to try to repair any part of the air bag system yourself. Be sure to tell anyone who works on your vehicle that it has an air bag system. • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function proper...

  • Page 131

    Law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the edr. Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requi...

  • Page 132

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child re- straint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrie...

  • Page 133

    Infant and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear- facing: infant carriers and conv...

  • Page 134

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • after a child restraint i...

  • Page 135

    Warning! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death. A child must always wear both the lap and shoulder portions of the seat belt correctly. Recommendatio...

  • Page 136

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchorage system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch-equipped child seats. There ...

  • Page 137

    Frequently asked questions about installing child restraints with latch what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child...

  • Page 138

    Frequently asked questions about installing child restraints with latch can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint ...

  • Page 139

    Locating the upper tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the l...

  • Page 140

    To install a latch-compatible child restraint in vehicles with rear seating if the selected seating position has a switchable automatic locking retractor (alr) seat belt, stow the seat belt, following the instructions below. See the section “installing child restraints using the vehicle seat belt” t...

  • Page 141

    Path and then buckle it. Do not lock the seat belt. Remind all children in the vehicle that the seat belts are not toys and that they should not play with them. Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be ba...

  • Page 142

    Lap/shoulder belt systems for installing child restraints in this vehicle frequently asked questions about installing child restraints with seat belts what is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing c...

  • Page 143

    Frequently asked questions about installing child restraints with seat belts can the rear-facing child restraint touch the back of the front passenger seat? Yes contact between the front passenger seat and the child restraint is allowed, if the child re- straint manufacturer also allows contact. Can...

  • Page 144

    4. Pull on the webbing to make the lap portion tight against the child seat. 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract back into the retractor. As the webbing retracts,...

  • Page 145

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 146

    Installing child restraints in commercial vehicles this commercial vehicle is not designed for use as a family vehicle and is not intended for carrying children in the front passenger seat(s). Never install rear-facing child restraints in this vehicle. If you must carry a child in a forward-facing c...

  • Page 147

    Lap/shoulder belt systems for installing child restraints in this vehicle installing a child restraint with a switchable automatic locking retractor (alr): child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt. Warning! • impr...

  • Page 148

    6. Try to pull the webbing out of the retractor. If it is locked, you should not be able to pull out any webbing. If the retractor is not locked, repeat step 5. 7. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward...

  • Page 149

    4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restr...

  • Page 150

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), whi...

  • Page 151

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 152

    Warning! (continued) upside down or turn your floor mat over. Lightly pull to confirm mat is secured using the floor mat fasten- ers on a regular basis. • always remove the existing floor mat from the vehicle before installing any other floor mat. Never install or stack an additional floor mat on to...

  • Page 153

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 155: Starting And Operating

    Starting and operating contents 䡵 starting the engine . . . . . . . . . . . . . . . . . .155 ▫ automatic transmission . . . . . . . . . . . . . . . . . .155 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . . .155 ▫ cold weather operation . . . . . . . . . . . . . . . . .155 ▫ extended p...

  • Page 156

    ▫ cleaning the parksense rear park assist system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 ▫ parksense rear park assist system usage precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .175 䡵 parkview rear back up camera . . . . . . . .177 䡵 refueling the vehicle . ....

  • Page 157

    Starting the engine before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 158

    Extended park starting note: extended park condition occurs when the vehicle has not been started or driven for at least 30 days. 1. Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle. 2. Cycle the ignition to the avv/start position and r...

  • Page 159

    Engine block heater — if equipped the engine block heater warms the engine and permits quicker starts in cold weather. Connect the cord to a 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. For ambient temperatures below 0°f (-18°c), the engine block heater is recommende...

  • Page 160

    While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving t...

  • Page 161

    When the parking brake is applied with the ignition switch in the on position, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is de...

  • Page 162

    Caution! If the brake system warning light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an au- thorized dealer immediately. Automatic transmission warning! • it is dangerous to shift out of park or neutral if the engine speed ...

  • Page 163

    Caution! Damage to the transmission may occur if the following precautions are not observed: • shift into or out of park or reverse only after the vehicle has come to a complete stop. • do not shift between park, reverse, neutral, or drive when the engine is above idle speed. • before shifting into ...

  • Page 164

    Note: in the event of a mismatch between the gear selector position and the actual transmission gear (for example, driver selects reverse while driving forward), the position indicator will blink continuously until the selector is returned to the proper position, or the requested shift can be comple...

  • Page 165

    Note: if the gear selector cannot be moved to the park, reverse, or neutral position (when pushed forward) it is probably in the ers (+/-) position (beside the drive position). In ers mode, the transmission gear limit (1, 2, 3, etc.) is displayed in the instrument cluster. Move the gear selector to ...

  • Page 166

    • remove the ignition key. Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage. • your vehicle could move and injure you and others if it is not in ...

  • Page 167

    Caution! • before moving the transmission gear selector out of park, you must turn the ignition to the on/run mode, and also press the brake pedal. Otherwise, damage to the gear selector could result. • do not race the engine when shifting from park or neutral into another gear range, as this can da...

  • Page 168

    Caution! (continued) refer to “recreational towing” in “starting and op- erating” and “towing a disabled vehicle” in “in case of emergency” for further information. Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts, and the best ...

  • Page 169

    A fixed gear, or may remain in neutral. The malfunction indicator light (mil) may be illuminated. Limp home mode may allow the vehicle to be driven to an authorized dealer for service without damaging the transmission. In the event of a momentary problem, the transmission can be reset to regain all ...

  • Page 170

    You can switch between drive and ers mode at any vehicle speed. When the gear selector is in the drive position, the transmission will operate automatically, shift- ing between all available gears. Moving the gear selector to the ers position (beside drive) will activate ers mode, display the curren...

  • Page 171

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Power steering fluid check checking the power steering fluid level at a define...

  • Page 172

    Speed control when engaged, the speed control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the speed control system has been designed to shut down i...

  • Page 173

    To set a desired speed turn the speed control on. When the vehicle has reached the desired speed greater than 25 mph (40 km/h), push the set (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. Note: the vehicle should be traveling at a steady speed and...

  • Page 174

    Metric speed (km/h) • pushing the set (-) button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a decrease of 1 km/h. • if the button is continually pushed, the set speed will continue to decrease until the button is released, then the new set speed ...

  • Page 175

    Parksense rear park assist — if equipped the parksense system provides an audible indication of the distance between the rear fascia/bumper and a de- tected obstacle when backing up, e.G. During a parking maneuver. Refer to “parksense rear park assist system usage precautions” for limitations of thi...

  • Page 176

    Parksense rear park assist alerts if an obstacle is behind the vehicle when reverse gear is engaged, an audible alert is activated. The tones emitted by the loudspeaker inform the driver that the vehicle is approaching an obstacle. The pauses between the tones are directly proportional to the distan...

  • Page 177

    While audible signals are emitted, the audio system is muted. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the distance measured by the inner sensors is constant. If this condition occurs for the external sensors, the signal is turned off...

  • Page 178

    Failure to do so can result in the system not working properly. The parksense system might not detect an obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/ bumper. • objects such as bicycle carriers, etc., must not be placed within 12 inc...

  • Page 179

    If it’s necessary to keep the ball mount and hitch ball assembly mounted for a long period, it is possible to filter out the ball mount and hitch ball assembly presence in sensor field of view. The filtering operation must be performed only by an authorized dealer. Parkview rear back up camera your ...

  • Page 180

    When displayed, static grid lines will illustrate the width of the vehicle and will show separate zones that will help indicate the distance to the rear of the vehicle. The follow- ing table shows the approximate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 ...

  • Page 181

    2. Remove the fuel cap by rotating it counterclockwise. 3. Fully insert the gasoline nozzle into the filler pipe. 4. Fill the vehicle with fuel. Note: when the fuel nozzle “clicks” or shuts off, the fuel tank is full. 5. Remove gasoline nozzle, reinstall fuel cap and close fuel filler door. Warning!...

  • Page 182

    Note: • when the fuel nozzle “clicks” or shuts off, the fuel tank is full. • tighten the fuel filler cap until you hear a “clicking” sound. This is an indication that the fuel filler cap is properly tightened. • if the gas cap is not tightened properly, the mil may come on. Be sure the gas cap is ti...

  • Page 183

    Warning! (continued) gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision. Tire size the tire size on the vehicle certification label represents the actual tire size on your vehicle. Replacement tires must be equal to...

  • Page 184

    The specified gvwr, you must redistribute the weight. Improper weight distribution can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Note: refer to the “vehicle certification label” affixed to the rear of the driver’s door for your vehicle’s gvwr a...

  • Page 185

    Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision. Tongue weight (tw) the tongue weight is the downward force exerted on the hitch ball by t...

  • Page 186

    May be required depending on vehicle and trailer configuration/loading to comply with gross axle weight rating (gawr) requirements. Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability, braking per- formance, and could result in a collision. • weight dist...

  • Page 187

    Trailer towing weights (maximum trailer weight ratings) note: for trailer towing information (maximum trailer weight ratings) refer to the following website addresses: • ramtrucks.Com/en/towing_guide/ • ramtruck.Ca (canada) • rambodybuilder.Com trailer and tongue weight never exceed the maximum tong...

  • Page 188

    Caution! (continued) • then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. This helps the engine and other parts of the vehicle wear in at the heavier loads. Perform the maintenance listed in the “scheduled se...

  • Page 189

    Warning! (continued) 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch utilized. Towing requirements — tires • do not attempt to tow a trailer while using a compact spare tire. • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to...

  • Page 190

    Caution! If the trailer weighs more than 1,000 lbs (453 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing requirements — trailer lights an...

  • Page 191

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic transmission the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. ...

  • Page 192

    Speed control — if equipped • do not use on hilly terrain or with heavy loads. • when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. • use speed control in flat terrain and with light loads to maximize fuel ef...

  • Page 193

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground automatic transmission flat tow none not allowed dolly tow front ok rear not allowed on trailer all ok note: when towing your vehicle, always follow appli- cable state and p...

  • Page 194

    Driving tips driving on slippery surfaces acceleration rapid acceleration on snow covered, wet, or other slippery surfaces may cause the driving wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels...

  • Page 195

    Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Further- more, flowing and/or rising water can carry your ve- hi...

  • Page 196

    Caution! (continued) • driving through standing water may cause damage to your vehicle’s drivetrain components. Always in- spect your vehicle’s fluids (i.E., engine oil, transmis- sion, axle, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through st...

  • Page 197: In Case Of Emergency

    In case of emergency contents 䡵 hazard warning flashers . . . . . . . . . . . .197 䡵 bulb replacement . . . . . . . . . . . . . . . . . . . .197 ▫ replacement bulbs . . . . . . . . . . . . . . . . . . . . .197 ▫ replacing exterior bulbs. . . . . . . . . . . . . . . . . .198 ▫ replacing interior bulb...

  • Page 198

    䡵 enhanced accident response system (ears) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .234 䡵 event data recorder (edr) . . . . . . . . . . . .234 196 in case of emergency.

  • Page 199

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency....

  • Page 200

    Lamps bulb number rear tail lamps p21/5w rear side marker lamps led (see your authorized dealer) center mount brake lamp w5w reverse light w16w front fog lamps h11 note: numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit yo...

  • Page 201

    Front/rear side marker lamps to change the bulb, proceed as follows: the front/rear side marker lamps are led and not ser- viced separately. See your authorized dealer for replace- ment of these lights. Rear tail, stop, backup and turn signal lamps the rear light clusters contain taillight, brake li...

  • Page 202

    2. Remove the bulbs by releasing them from the side contacts; insert the new bulbs and make sure they are correctly clamped between these contacts. Replacing interior bulbs dome lamp with spot lights to change the bulbs, proceed as follows: 1. Remove dome lamp by depressing the tabs located by the a...

  • Page 203

    Rear roof lamp to change the bulb, proceed as follows: 1. Remove roof lamp by depressing the tabs located by the arrows, using a suitable tool. 2. Open the cover. Roof lamp roof lamp (reverse side) 1 — cover 7 in case of emergency 201.

  • Page 204

    3. Replace the bulb releasing them from the side contacts making sure that the new bulbs are correctly secured between the contacts. 4. Close the protective cover and reposition it back into its housing, making sure that it locks into place. Fuses warning! • when replacing a blown fuse, always use a...

  • Page 205

    Underhood fuses the front distribution unit is located on the right side of the engine compartment, next to the battery. To access the fuses, remove fasteners and remove the cover. The id number of the electrical component corresponding to each fuse can be found on the back of the cover. Cavity maxi...

  • Page 206

    Cavity maxi fuse mini fuse description f02 30 amp green – fog lamps, front heated seats (if equipped) f02 20 amp yellow – front heated seats f03 20 amp yellow – ignition switch f04 40 amp orange – bsm system module f06 20 amp yellow – radiator fan - low speed f07 50 amp red – radiator fan - high spe...

  • Page 207

    Cavity maxi fuse mini fuse description f24 – 5 amp tan bsm system, positive key and steering angle sensor f30 – 15 amp blue 2nd instrument panel power outlet f83 20 amp yellow – fuel pump f84 – 15 amp blue at module f85 – 15 amp blue rear power outlet 12v f86 – 15 amp blue ip power outlet 12v f87 – ...

  • Page 208

    Cavity mini fuse description f53 5 amp beige kl 30 (+30) - ipc f38 20 amp yellow central doors locking f36 15 amp blue kl 30 (+30) - tpms, eobd, hvac, radio, sgw fuse panel cavity locations 206 in case of emergency.

  • Page 209

    Cavity mini fuse description f43 15 amp blue bi-directional washer pump f48 20 amp yellow passenger power windows f50 7.5 amp brown kl 15 (+15) - air-bag f51 7.5 amp brown kl 15 (+15) - external mirror adjust- ment command, hvac, rvc, hwb coils f37 5 amp beige kl 15 (+15) - brake pedal switch (n.O.)...

  • Page 210

    Central unit fuse panel the central power fuse panel is located on the driver’s side under the instrument panel. Cavity mini fuse description f1 10 amp red front heated seat passenger f2 10 amp red front heated seat driver f3 20 amp yellow rear power window driver side f4 20 amp yellow rear power wi...

  • Page 211

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 212

    Removing the spare tire 1. Remove the spare tire before attempting to jack up the vehicle. Attach the wrench handle to the winch exten- sion. 2. To access the winch mechanism open the rear doors of the vehicle to expose the winch mechanism access cover. Remove the access cover and install the winch ...

  • Page 213

    3. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. Note: the winch mechanism is designed for use with the winch extension only. Use of an air wrench or other power tools is not recommend...

  • Page 214

    5. Remove the retainer nut prior to removing the retainer from the wheel. 6. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. Retainer nut lifting spare tire 212 in case of emergency.

  • Page 215

    7. Pull the retainer through the center of the wheel. Preparations for jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull f...

  • Page 216

    Warning! (continued) • turn on the hazard warning flasher. • block the wheel diagonally opposite the wheel to be raised. • set the parking brake firmly and set an automatic transmission in park; a manual transmission in reverse. • never start or run the engine with the vehicle on a jack. • do not le...

  • Page 217

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Loosen (but do not remove) the wheel lug bolts with the wrench handle by turning them to the left one turn while the wheel is still on the ground. 2. There...

  • Page 218

    Warning! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift...

  • Page 219

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 3. Turn the handle on the jack screw to the right until the jack head is properly engaged in the described location. Do not raise the vehicle until you are su...

  • Page 220

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel lug bolts. For vehicles with wheel covers, remove the cover from the wheel by hand. Do not p...

  • Page 221

    Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. 10. Stow the cable and wheel spacer before drivi...

  • Page 222

    2. The plastic fin must be directed downwards and per- fectly coincide with the flange cut part; fit the bracket in the adapter, fold the bracket up and secure it to the adapter with the fastening knob. 3. Position the tire vertically and lay the mounted adapter on the inner part of the rim, using t...

  • Page 223

    Vehicles equipped with wheel covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two wheel bolts on the wheel. Install the wheel bolts with the threaded end of the bolt toward the wheel. Lightly tighten the wheel bolts. 3. Align ...

  • Page 224

    7. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are properly seated against the wheel. Tire service kit — if equipped small punctures up to ¼” (6 mm) in the tire tread can be sealed with tire service kit. Foreign objects (e.G., screws or nail...

  • Page 225

    Warning! • do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the tire service kit. • do not use tire service kit or drive the vehicle under the following circumstances: – if the puncture in the tire t...

  • Page 226

    Off and remove the tire service kit, drive the vehicle 30 feet (10 meters) back and forth, to better distribute the sealant inside the tire. Attach the clear flexible filling tube of the compressor directly to the tire valve and repeat the inflation process. When the correct pressure has been reache...

  • Page 227

    Warning! Store the sealant canister in its special compartment, away from sources of heat. Failure to follow this warning may result in sealant canister rupture and serious injury or death. Jump starting if your vehicle has a discharged battery, it can be jump started using a set of jumper cables an...

  • Page 228

    Warning! • take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. (continued) warning! (continued) • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadver...

  • Page 229

    Jump starting procedure warning! Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Con...

  • Page 230

    4. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the vehicle with the discharged battery. If frequent jump-starting is required to start your vehicle you should have the battery and charging system in- spected at an authorized dealer. Caution! Accessories...

  • Page 231

    6. Pull the release tab downwards using one hand and with the other one remove the key, sliding it outwards. 7. Once the key is removed, reinstall the steering column cover. Caution! It is advisable to contact your authorized dealer to have the reinstall procedure carried out. If you would like to p...

  • Page 232

    5. Insert a small screwdriver or a similar tool into the gear selector override access hole (at the right front corner of the gear selector assembly), then push and hold the override release lever down. While holding the override release lever down, push the lock button on the gear selector and move...

  • Page 233

    Warning! (continued) see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot. Caution! Driving with a hot cooling system could damage your vehicle. If the te...

  • Page 234

    Warning! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously witho...

  • Page 235

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. Towing condition wheel off the ground all models flat tow none not allowed wheel lift or dolly tow front ok rear not allowed flatbed all best method proper towing or lifting e...

  • Page 236

    If flatbed equipment is not available, this vehicle must be towed with the front wheels off the ground (using a towing dolly, or wheel lift equipment with the front wheels raised). Caution! Towing this vehicle in violation of the above require- ments can cause severe transmission damage. Damage from...

  • Page 237: Servicing And Maintenance

    Servicing and maintenance contents 䡵 scheduled servicing . . . . . . . . . . . . . . . . .237 ▫ maintenance plan. . . . . . . . . . . . . . . . . . . . . . .238 䡵 engine compartment . . . . . . . . . . . . . . . . .241 ▫ engine compartment — 2.4l . . . . . . . . . . . . . .241 ▫ checking oil level ....

  • Page 238

    ▫ tire rotation recommendations . . . . . . . . . . . .282 䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . .283 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . . .283 ▫ t...

  • Page 239

    Scheduled servicing your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This ...

  • Page 240

    Maintenance plan required maintenance intervals refer to the maintenance schedules on the following page for the required maintenance intervals. At every oil change interval as indicated by oil change indicator system: • change oil and filter • rotate the tires rotate at the first sign of irregular ...

  • Page 241

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 242

    *** the spark plug change interval is mileage based only, yearly intervals do not apply. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a serv...

  • Page 243

    Engine compartment engine compartment — 2.4l 1 — air cleaner filter 5 — power distribution center (fuses) 2 — power steering fluid reservoir 6 — washer fluid reservoir 3 — oil fill cap 7 — engine coolant pressure cap 4 — brake fluid reservoir 8 — engine oil dipstick 8 servicing and maintenance 241.

  • Page 244

    Checking oil level to assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off. Checking th...

  • Page 245

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, no...

  • Page 246

    Dealer service your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service opera- tions in an expert manner. Service manuals are available which include detailed service information for your ve- hicle. Refer to these service manuals before attempti...

  • Page 247

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity (sae grade) — 2.4l engine mopar sae 0w-20 engine oil approved to fca material standard ms-6395 such as pennzoil, shell...

  • Page 248

    Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow type dispos- able oil filter. Use a filter of this type for replacement. The quality of replacement filters varies conside...

  • Page 249

    Warning! (continued) system. Some unapproved refrigerants are flam- mable and can explode, injuring you. Other unap- proved refrigerants or lubricants can cause the sys- tem to fail, requiring costly repairs. Refer to warranty information book, for further warranty information. • the air conditionin...

  • Page 250

    And grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood ser- vices, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubric...

  • Page 251

    5. Carefully lower the blade, bringing it back in contact with the windshield. 6. Bring the blade to the initial rest position, turning the ignition to mar-on. Note: do not operate the wiper with the blades lifted from the windshield. Exhaust system the best protection against carbon monoxide entry ...

  • Page 252

    Caution! (continued) the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible dam...

  • Page 253

    Warning! (continued) • keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised. The fan starts automatically and may start at any time, whether the engine is running or not. • when working near the radiator cooling fan, discon- nect the fan motor lead or t...

  • Page 254

    Note: • mixing of engine coolant (antifreeze) other than speci- fied organic additive technology (oat) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive tech- nology (oat) engine coolant is different and should not be mixed with hybrid o...

  • Page 255

    • mix a minimum solution of 50% oat engine coolant that meets the requirements of fca material standard ms.90032 and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below −34°f (−37°c) are anticipated. Please contact an authorized dealer for assistance. • use only high...

  • Page 256

    Warning! (continued) overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • do not use a pressure cap other than the one speci- fied for your vehicle. Personal injury or eng...

  • Page 257

    • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (antifreeze) needs to be added, the contents of the coolant expansion bottle must also be protected against freezing. • if frequent engine coolant (antifreeze) additions are required, the cooling ...

  • Page 258

    Checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Refer to “fluids and lubricants” in “technical specifications” for further information. Warning! • use only manufacturer’s recommended brake ...

  • Page 259

    Warning! Because it is flammable, do not allow the power steering fluid to come into contact with hot engine parts note: power steering fluid consumption is very low. If you need to top off your fluid often and multiple times have your system inspected by your authorized dealer. Automatic transmissi...

  • Page 260

    Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating conditions. Routine fluid level checks are not required; therefore the transmis- sion has no dipstick. An authorized dealer can check your transmission fluid level using special service ...

  • Page 261

    15 way vehicle connector functions and view pin function 1 not connected 2 alternator system charging in process signal 3 vehicle speed repetition (vso) 4 not connected 5 not connected 6 not connected 7 additional courtesy light 8 courtesy lights negative control (dimmed) 9 not connected 10 not conn...

  • Page 262

    This connector is supplied to the upfitter when the vehicle is ordered with the applicable package. 2 way vehicle connector functions and view pin function a power supply b gnd upfitter connector connector pins 260 servicing and maintenance.

  • Page 263

    This connector is supplied to the upfitter when the vehicle is ordered with the applicable package. Caution! The maximum current load allowed is 15 amps for continuous use. For additional questions about these connectors as well as general technical questions about upfitting your ram prod- uct, refe...

  • Page 264

    Tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to th...

  • Page 265

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ....Blank....ⴖ = passenger car tire based on european design standards, or lt = light truck tire based o...

  • Page 266

    Example: h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions – the maximum speed corresponding to the speed symbol should only be achieved under specified operating condi- tions (i.E., tire p...

  • Page 267

    Tire identification number (tin) the tin may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 268

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located be- hind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hour...

  • Page 269

    Tire loading and tire pressure note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure...

  • Page 270

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 271

    Steps for determining correct load limit— (1) locate the statement “the combined weight of occupants and cargo should never exceed xxx kg or xxx lbs.” on your vehicle’s placard. (2) determine the combined weight of the driver and passengers that will be riding in your vehicle. (3) subtract the combi...

  • Page 272

    • for the following example, the combined weight of occu- pants and cargo should never exceed 865 lbs (392 kg). Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and (continued) warning! (continued) increase your stopping distance. Use tire...

  • Page 273

    Tires — general information tire pressure proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Four primary areas are affected by improper tire pressure: • safety and vehicle stability • economy • tread wear • ride comfort safety warning! • improperly i...

  • Page 274

    Tread wear improper cold tire inflation pressures can cause abnormal wear patterns and reduced tread life, resulting in the need for earlier tire replacement. Ride comfort and vehicle stability proper tire inflation contributes to a comfortable ride. Over-inflation produces a jarring and uncomfortab...

  • Page 275

    Pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire ...

  • Page 276

    Run flat tires — if equipped run flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the run flat mode. A run flat mode occurs when the tire inflation pressure is of/or below 14 psi...

  • Page 277

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be re- placed. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (1.6 mm). When t...

  • Page 278

    Warning! (continued) you could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement tires the tires on your new vehicle p...

  • Page 279

    Warning! (continued) • never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • failure to equip your vehicle wi...

  • Page 280

    Snow tires some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a “mountain/snowflake” symbol on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the origi- nal equipment tires. Use snow tires only in sets of...

  • Page 281

    Compact spare tire — if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on the tire and loading information placard located on the driver’s side door opening or on the sidewall ...

  • Page 282

    Do not install a wheel cover or attempt to mount a conventional tire on the collapsible spare wheel, since the wheel is designed specifically for the collapsible spare tire. Warning! Compact and collapsible spares are for temporary emergency use only. With these spares, do not drive more than 50 mph...

  • Page 283

    Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neu- tral ph) soap and water to maintain their luster and to prevent corrosion. Wash wheels with the same soap solution recommended for the body of the vehicle a...

  • Page 284

    Dark vapor chrome, black satin chrome, or low gloss clear coat wheels caution! If your vehicle is equipped with these specialty wheels, do not use wheel cleaners, abrasives, or polishing compounds. They will permanently damage this finish and such damage is not covered by the new vehicle limited war...

  • Page 285

    The suggested rotation method is the “forward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Department of transportation uniform tire quality grades the following tire grading categories were established by the nation...

  • Page 286

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 287

    Bodywork protection from atmospheric agents vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehic...

  • Page 288

    • if insects, tar, or other similar deposits have accumulated on your vehicle, use mopar super kleen bug and tar remover to remove. • use a high quality cleaner wax, such as mopar cleaner wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • avoid ...

  • Page 289

    Interiors seats and fabric parts use mopar total clean to clean fabric upholstery and carpeting. Note: power washing is not allowed inside the vehicle (both passenger and cargo area). Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed a...

  • Page 290

    Note: if equipped with light colored leather, it tends to show any foreign material, dirt, and fabric dye transfer more so than darker colors. The leather is designed for easy cleaning, and fca recommends mopar total care leather cleaner applied on a cloth to clean the leather seats as needed. Cauti...

  • Page 291: Technical Specifications

    Technical specifications contents 䡵 identification data. . . . . . . . . . . . . . . . . . .290 ▫ vehicle identification number . . . . . . . . . . . . .290 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . . .290 䡵 wheel and tire torque specifications . .290 ▫ torque specifications . . . ....

  • Page 292

    Identification data vehicle identification number the vehicle identification number (vin) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the vehicle frame and underbody as well as the automobile informa- tion disclosure label af...

  • Page 293

    Torque specifications lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 63 ft-lbs (86 n·m) steel wheels only 89 ft-lbs (120 n·m) alu- minum wheels only m12 x 1.25 17 mm **use only your authorized dealer recommended lug nuts/ bolts and clean or remove any dirt or oil before tightening....

  • Page 294

    After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may...

  • Page 295

    Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline”. Reformulated gasoline contains oxygenates and are specifi- cally blended to reduce vehicle emissions and improve air quality. The use of reformulated gasoline is recomm...

  • Page 296

    Cng and lp fuel system modifications modifications that allow the engine to run on compressed natural gas (cng) or liquid propane (lp) may result in damage to the engine, emissions, and fuel system compo- nents. Problems that result from running cng or lp are not the responsibility of the manufactur...

  • Page 297

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition ...

  • Page 298

    Fluid capacities u.S. Metric fuel (approximate) 2.4l engine 16 gallons 60.5 liters engine oil with filter 2.4 liter engine (sae 0w-20, api certified) 5.5 quarts 5.2 liters cooling system* 2.4 liter engine (mopar antifreeze/ engine coolant 10 year/150,000 mile formula) 7.2 quarts 6.8 liters * include...

  • Page 299

    Fluids and lubricants engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive tech- nology) or equivalent meeting the requirements of fca material standard ms.90032. Engine oil – 2.4l engine we...

  • Page 300

    Caution! (continued) introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh oat coolant (conforming to ms.90032), by an authorized dealer as soon as pos- sible. • do not use water alone or alcohol-based engine coolant (antifre...

  • Page 301: Multimedia

    Multimedia contents 䡵 uconnect radios . . . . . . . . . . . . . . . . . . . .300 䡵 cybersecurity . . . . . . . . . . . . . . . . . . . . . . . .300 䡵 uconnect settings . . . . . . . . . . . . . . . . . . .301 ▫ customer programmable features — uconnect 3 settings . . . . . . . . . . . . . . . . . . ...

  • Page 302

    Uconnect radios for detailed information about your uconnect radio, refer to your uconnect owner’s manual supplement. Note: uconnect screen images are for illustration pur- poses only and may not reflect exact software for your vehicle. Cybersecurity your vehicle may be a connected vehicle and may b...

  • Page 303

    Note: • fca or your dealer may contact you directly regarding software updates. • to help further improve vehicle security and minimize the potential risk of a security breach, vehicle owners should: • routinely check www.Driveuconnect.Com/software- update (u.S. Residents) or www.Driveuconnect.Ca/ s...

  • Page 304

    Customer programmable features — uconnect 3 settings push the settings button on the faceplate to display the menu setting screen. In this mode the uconnect system allows you to access programmable features that may be equipped such as language, display, units (if equipped), voice, clock, safety & d...

  • Page 305

    Language after pressing the “language” button on the touchscreen, the following settings will be available: setting name selectable options set language note: when the “set language” feature is selected, you may select one of multiple languages (english/français/español) for all display nomenclature...

  • Page 306

    Setting name selectable options units — if equipped us metric note: when selecting the “units” setting, the changes can be made to the distance (mi, km), fuel consumption (mpg if set to mi, l/100 km or km/l if set to km), and temperature (°c, °f). Touchscreen beep display trip b note: press the rele...

  • Page 307

    Voice after pressing the “voice” button on the touchscreen, the following settings will be available: setting name selectable options voice response length brief detailed show command list never with help always note: this setting will display the possible options while in a voice session. Clock & d...

  • Page 308

    Setting name selectable options show time in status bar — if equipped note: the “show time in status bar” feature will allow you to turn on or shut off the digital clock in the status bar. Set date month day year note: within the “set date” setting, press the corresponding arrow buttons on the touch...

  • Page 309

    Lights after pressing the “lights” button on the touchscreen, the following settings will be available: setting name selectable options daytime running lights — if equipped on off note: when the “daytime running lights” feature is selected, the headlights will turn on whenever the engine is running....

  • Page 310

    Engine off options after pressing the “engine off options” button on the touchscreen, the following settings will be available: setting name selectable options radio off delay 0 min 20 min note: when this setting is selected, the radio will remain off for the selected amount of time when the engine ...

  • Page 311

    Setting name selectable options balance speaker icon arrow buttons note: when in this display you may adjust the “balance/fade” of the audio by using the “arrow” button on the touchscreen to adjust the sound level from the front and rear or right and left side speakers. Press the “speaker icon” on t...

  • Page 312

    Setting name selectable options aux volume offset + – note: this feature provides the ability to tune the audio level for portable devices connected through the aux in- put. Phone after pressing the “phone” button on the touchscreen, the following settings will be available: setting name selectable ...

  • Page 313

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be available: setting name selectable options tune start note: the “tune start” feature begins playing the current song from the beginning when you tune to a music channel using ...

  • Page 314

    Setting name selectable options subscription info sirius id note: new vehicle purchasers or lessees will receive a free limited time subscription to siriusxm satellite radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the subscrip...

  • Page 315

    Setting name selectable options regional on off note: forces the system to select from a network station when the system is present in a different region. Restore settings — if equipped after pressing the “restore settings” button on the touch- screen, the following settings will be available: setti...

  • Page 316

    Steering wheel audio controls — if equipped the remote sound system controls are located on the back surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push-button in the center. Pushing the top of the switch will incre...

  • Page 317

    Ipod/usb/mp3 control — if equipped the usb input and auxiliary jack is located on the instrument panel below the climate controls. This feature allows an ipod or external usb device to be plugged into the usb port. Ipod control supports mini, 4g, photo, nano, 5g ipod and iphone devices. Some ipod so...

  • Page 318

    The radio manufacturer believes the internal wireless radio is safe for use by consumers. The level of energy emitted is far less than the electromagnetic energy emitted by wire- less devices such as mobile phones. However, the use of wireless radios may be restricted in some situations or environme...

  • Page 319

    Uconnect 3/3 nav voice recognition quick tips — if equipped introducing uconnect start using uconnect voice recognition with these helpful quick tips. It provides the key voice commands and tips you need to know to control your uconnect 3/3 nav system. Key features: • 5.0” full color touchscreen dis...

  • Page 320

    3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is positioned in the dome lamp and aimed at the driver. 4. Each time you give a voice command, you must first push either the vr or phone button, wait until after the beep, then say your voice command. 5. You ca...

  • Page 321

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect system. Push the vr button . After the beep, say: • “ cancel” to stop a current voice session • “ help” to hear a list of suggested voice commands • “ repeat” to listen to the system prompts again...

  • Page 322

    Media uconnect offers connections via usb, bluetooth and auxil- iary ports (if equipped). Voice operation is only available for connected usb and ipod devices. Push the vr button . After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artis...

  • Page 323

    • “ redial (call previous outgoing phone number)” • “ call back (call previous incoming phone number)” tip: when providing a voice command, push the vr button or phone button and say “ call,” then pronounce the name exactly as it appears in your phone book. When a contact has multiple phone numbers,...

  • Page 324

    Pre-defined voice text reply responses i’ll call you later. I need directions. See you in 10, 15, 20, 25, 30, 45, 60> of min- utes. I’m on my way. Can’t talk right now. I’m lost. Thanks. Note: only use the numbering listed otherwise the sys- tem does not transpose the message. Tip: your mobile phone...

  • Page 325

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 327: Customer Assistance

    Customer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . .326 ▫ prepare for the appointment . . . . . . . . . . . . . .326 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . .326 ▫ be reasonable with requests . . . ...

  • Page 328

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 329

    Any communication to the manufacturer’s customer center should include the following information: • owner’s name and address • owner’s telephone number (home and office) • authorized dealer name • vehicle identification number (vin) • vehicle delivery date and mileage fca us llc customer center p.O....

  • Page 330

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommunica- tion devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 331

    Warning! Engine exhaust (internal combustion engines only), some of its constituents, and certain vehicle compo- nents contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids con- tained in vehicles and c...

  • Page 332

    In canada if you believe that your vehicle has a safety defect, you should contact the customer service department imme- diately. Canadian customers who wish to report a safety defect to the canadian government should contact transport canada, motor vehicle defect investigations and recalls at 1-800...

  • Page 333: Index

    Index 12.

  • Page 334

    Adding engine coolant (antifreeze) . . . . . . . . . . . . .252 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . .294 air bag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 air bag operation . . . . . . . . . . . . . . . . . . . . . . . .120 driver knee ai...

  • Page 335

    B-pillar location . . . . . . . . . . . . . . . . . . . . . . . . . . .267 brake assist system . . . . . . . . . . . . . . . . . . . . . . . . .97 brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .298 brake, parking. . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 b...

  • Page 336

    Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 cold weather operation. . . . . . . . . . . . . . . . . . . . . .155 compact disc (cd) maintenance. . . . . . . . . . . . . . . .323 compact spare tire . . . . . . . . . . . . . . . . . . . . . . . . .279 contract, service . . ...

  • Page 337

    Emergency, in case of freeing vehicle when stuck . . . . . . . . . . . . . . . . .231 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . .209, 261 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . .225 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2...

  • Page 338

    Folding rear seat . . . . . . . . . . . . . . . . . . . . . . . . . . .29 four-way hazard flasher. . . . . . . . . . . . . . . . . . . . .197 freeing a stuck vehicle . . . . . . . . . . . . . . . . . . . . . .231 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .292 additiv...

  • Page 339

    Immobilizer (sentry key) . . . . . . . . . . . . . . . . . . . . . .20 inside rearview mirror . . . . . . . . . . . . . . . . . . . . . . .38 instrument cluster . . . . . . . . . . . . . . . . . . . . . . . .72, 91 instrument cluster display instrument cluster display . . . . . . . . . . . . . . . ....

  • Page 340

    Tire pressure monitoring (tpms) . . . . . . . . . . .88, 101 traction control . . . . . . . . . . . . . . . . . . . . . . . . .100 turn signal . . . . . . . . . . . . . . . . . . . . . . . . . .91, 151 warning (instrument cluster description) . . . . .85, 91 loading vehicle . . . . . . . . . . . . ....

  • Page 341

    Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . .245, 296 oil filter, change . . . . . . . . . . . . . . . . . . . . . . . . . .246 oil filter, selection. . . . . . . . . . . . . . . . . . . . . . . . . .246 oil pressure light . . . . . . . . . . . . . . . . . . . . . . . . . . .86 onb...

  • Page 342

    Safety checks outside vehicle . . . . . . . . . . . . . . . . .151 safety defects, reporting . . . . . . . . . . . . . . . . . . . . .329 safety, exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .148 safety information, tire . . . . . . . . . . . . . . . . . . . . . .261 safety tips . . ....

  • Page 343

    Specifications fuel (gasoline) . . . . . . . . . . . . . . . . . . . . . . . . . .297 oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 speed control accel/decel . . . . . . . . . . . . . . . . . . . . . . . . . . . .172 cancel . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 344

    Spare tire . . . . . . . . . . . . . . . . . . . . . . . . . .278, 280 spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .274 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . .187 tread wear indicators . . . . . . . . . . . . . . . . . . . . .275 wheel nut torque...

  • Page 345

    Warnings and cautions . . . . . . . . . . . . . . . . . . . . . . .6 warranty information . . . . . . . . . . . . . . . . . . . . . . .329 washers, windshield. . . . . . . . . . . . . . . . . . . . . .47, 242 washing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . .285 water driving thro...

  • Page 346

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 347

    Second edition printed in the u.S.A. ©2017 fca us llc. All rights reserved. Ram is a registered trademark of fca us llc. 18vm-126-ab p r o m a s t e r c i t y o w n e r ’ s m a n u a l 2 0 1 8 promaster cit y 2018.