1. DL manuals
  2. RAM
  3. Automobile
  4. RAM CV Cargo Van 2012
  5. Owner's Manual

RAM RAM CV Cargo Van 2012 Owner's Manual

Summary of RAM CV Cargo Van 2012

  • Page 1

    R a m c v c a r g o v a n chrysler group llc o w n e r ’ s m a n u a l 2 0 1 2 2 0 12 ram c argo v an 12mzz-126-aa first edition printed in u.S.A. 1199168 ram truck 1500-2500-3500 om cover.Indd 1 3/29/12 2:55 pm.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 4 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 6 䡵 vehicle identification number . . . . . . . . . . . . . . 6 䡵 vehicle modifica...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Introduction 5.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 9

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Stamped vin location 1 introduction 7.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ wireless ignition node (win) . . . . . . . . . . . . 12 䡵 sentry key威 . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ▫ replacement keys . . . . . . . . . . . . . . . . . . . ....

  • Page 12

    䡵 sliding side door . . . . . . . . . . . . . . . . . . . . . . 41 ▫ power sliding side door — if equipped . . . . . 42 ▫ sliding side door child protection lock . . . . . 46 䡵 liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 ▫ power liftgate — if equipped . . . . . . . . . . . ...

  • Page 13

    䡵 commercial cargo vehicles (no factory installed rear seats) — if equipped . . . . . . . . . . 95 ▫ restraining infants and small children in commercial cargo vehicles . . . . . . . . . . . . . . 97 䡵 engine break-in recommendations . . . . . . . . . . 98 䡵 safety tips . . . . . . . . . . . . . . ....

  • Page 14

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a wireless ignition node (win) with integral ignition switch. You can insert the key fob into the ignition switch with either side up. Wireless igniti...

  • Page 15

    Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key ...

  • Page 16

    Removing key fob from ignition place the shift lever in park. Turn the key fob to the off position and then remove the key fob. Note: power window switches will also remain active for up to 10 minutes after the ignition switch has been turned to off, depending upon the accessory delay setting. Openi...

  • Page 17

    Caution! An unlocked car is an invitation to thieves. Always remove the key fob from the ignition and lock all doors when leaving the vehicle unattended. Key-in-ignition reminder opening the driver’s door when the key fob is in the ignition and the ignition switch position is off or acc, a chime wil...

  • Page 18

    If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than 10 sec- onds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. Caution! The sentry key 威 immobilize...

  • Page 19

    Customer key programming programming key fobs or rke transmitters may be performed at an authorized dealer. General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause h...

  • Page 20

    •make sure the vehicle ignition system is ⬙off⬙ and the key is physically removed from the ignition. 2. Perform one of the following methods to lock the vehicle: • press lock on the interior power door lock switch with the driver and/or passenger door open. • press the lock button on the remote keyl...

  • Page 21

    Vehicle security alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the vehicle security alarm. If the vehicle security alarm is armed and the battery becomes disconnected, the vehicle securit...

  • Page 22

    Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors and liftgate, and activate the panic alarm, optional power liftgate, left power sliding door, and right power sliding door from distances up to approximately 66 ft (20 m) using a hand-held key fob with rke tr...

  • Page 23

    (optional), power sliding doors, remote start feature (optional). Some features can be programmed to the customers preferences. For example, flash headlights or sound horn on lock. Remote unlock doors and liftgate press and release the unlock button on the rke transmitter once to unlock the driver’s...

  • Page 24

    • for vehicles not equipped with the evic, the remote unlock feature can be enabled or disabled by perform- ing the following steps: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the lock button on a programmed rke transmitter for at least 4 seconds, but no longer t...

  • Page 25

    Settings (customer-programmable features)” in “un- derstanding your instrument panel” for further infor- mation. • for vehicles not equipped with the evic, perform the following steps: 1. Perform this operation while standing outside the vehicle. 2. Press the lock button on a programmed rke trans- m...

  • Page 26

    Note: • when you turn off the panic alarm by pressing the panic button a second time, you may have to move closer to the vehicle due to the radio frequency (rf) noises of the system. • the panic alarm cannot be activated if the engine is running. Power open/close power liftgate — if equipped press t...

  • Page 27

    If the vehicle is locked and the vehicle security alarm is armed, pressing the left power sliding door button twice unlocks the power sliding door and disarms ve- hicle security alarm. Power open/close right power sliding door — if equipped press the right power sliding door button twice on the rke ...

  • Page 28

    2. Press and hold the unlock button on a programmed rke transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the lock button while still holding the unlock button. 3. Release both buttons at the same time. 4. Test the feature while outside of the vehicle by press- ...

  • Page 29

    2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. Emergency key removal inserting emergency key into slot 2 things to know before starting your vehicle 27.

  • Page 30

    3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it wit...

  • Page 31

    Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m). Note: • the vehicle must be equipped with an automatic...

  • Page 32

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Car- bon monoxide is poisonous and can cause serious injury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 33

    Note: • if your power door locks were unlocked, remote start will automatically lock the doors. • the park lights will turn on and remain on during remote start mode. • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the remote start mode. •...

  • Page 34

    Cancel remote start remote starting will also cancel if any of the following occur: • the engine stalls or engine speed exceeds 2500 rpm • any engine warning lights come on • low fuel light turns on • the hood is opened • the hazard switch is pressed • the shift lever is moved out of park • the engi...

  • Page 35

    If the lock knob is down when you shut either front door, the door will lock. Make sure the keys are not inside the vehicle before closing the door. If the lock knob is rearward when you shut either side sliding door, the door will lock. Make sure the keys are not inside the vehicle before closing t...

  • Page 36

    Warning! • for personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or wi...

  • Page 37

    Accidentally locking your keys in the vehicle. Removing the key fob or closing the door will allow the locks to operate. A chime will sound if the key fob is in the ignition switch and a door is open, as a reminder to remove the key fob. If you press the power door lock switch while the sliding door...

  • Page 38

    The unlock doors automatically on exit feature will not operate if there is any manual operation of the power door locks (lock or unlock). On vehicles equipped with the optional electronic ve- hicle information center (evic), refer to “electronic vehicle information center (evic)/personal settings (...

  • Page 39

    Note: power window switches will also remain active for up to 10 minutes after the ignition switch has been turned to off, depending upon the accessory delay setting. Opening a front door will cancel this feature. Power window lockout switch — if equipped the driver may lock out the rear power windo...

  • Page 40

    Front passenger power window switch there is a single switch on the front passenger’s door trim panel which operates the passenger door window and a set of switches that lock and unlock all doors. The switches will operate only when the ignition switch is in the on/run or acc position and during pow...

  • Page 41

    Auto-down feature — if equipped the front window switches may be equipped with an auto-down feature. Press the window switch past the detent, release, and the window will go down automati- cally. To open the window part way, press the window switch part way and release it when you want the window to...

  • Page 42

    • any impact due to rough road conditions may trigger the auto reverse function unexpectedly during auto- closure. If this happens, pull the switch lightly to the first detent and hold to close window manually. Warning! There is no anti-pinch protection when the window is almost closed. To avoid per...

  • Page 43

    Note: the sliding door windows do not fully open, stopping several inches above the window sill. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunr...

  • Page 44

    • avoid high impacts against the door stop when open- ing the door. This is very important when your vehicle is parked on an incline as the door will slide faster in the downhill direction. • there is a hold-open latch that is activated when the sliding door is fully opened. This latch will keep you...

  • Page 45

    For the driver and passengers. Pressing the switch once will open the power sliding door. If the switch is pressed while the door is under a power cycle, the door will reverse direction. Note: the power sliding side door must be unlocked before the power sliding door switches will operate. If the in...

  • Page 46

    • if anything obstructs the power sliding side door while it is closing or opening, the door will automati- cally reverse to the closed or open position, provided it meets sufficient resistance. • if the power sliding side door is not in the full open or close position, it will fully open when a pow...

  • Page 47

    3. Within 10 seconds of the final cycle, press the haz- ard switch on. 4. A single chime will sound to signify that you have successfully completed the programming. You can turn the feature back on by repeating the previous procedure. Power sliding side door master lock switch to provide a safer env...

  • Page 48

    Sliding side door child protection lock to provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a child protection door lock system. Note: when the child protection door lock system is engaged, the door can be opened only by using the outside d...

  • Page 49

    • when the child protection door lock system is en- gaged, (even if the inside door lock is in the unlocked position) the door can be opened only by using the outside door handle, the rke transmitter, the switches on the overhead console or the switches located on the trim panel just in front of the...

  • Page 50

    Note: • after setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position. • the power sliding side door switches will not open the power sliding doors if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). • the ...

  • Page 51

    Power liftgate — if equipped the power liftgate may be opened manually or by using the button on the remote keyless entry (rke) transmit- ter. Press the button on the transmitter twice within five seconds, to open the power liftgate. When the liftgate is fully open, pressing the button twice within ...

  • Page 52

    The power liftgate may be closed by pressing the button, located in the upper left trim in the liftgate opening. Pushing once will only close the liftgate. This button cannot be used to open the liftgate. When the rke transmitter button is pressed and the flash lights feature is enabled, the tail li...

  • Page 53

    • there are also pinch sensors attached to the side of the liftgate opening. Light pressure anywhere along these strips will cause the liftgate to return to the open position. • during power operation, whether liftgate is fully open or fully closed, the liftgate chime will beep several times indicat...

  • Page 54

    Warning! (continued) • if you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. Do not use the recirculation mode. Gas props support the liftgate in the open position. However, because the gas pressure dro...

  • Page 55

    • all seat belt systems (except the driver’s and third row center) include automatic locking retractors (alrs), which lock the seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a ...

  • Page 56

    Secured in the rear seat in child restraints or belt- positioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. If a chi...

  • Page 57

    Warning! (continued) • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • supplemen...

  • Page 58

    You under normal conditions. However, in a collision the belt will lock and reduce the risk of you striking the inside of the vehicle or being thrown out. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely ...

  • Page 59

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbi...

  • Page 60

    Warning! • a belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so t...

  • Page 61

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you properly. In a sudden stop...

  • Page 62

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • a twisted belt may not protect you properly. In a colli...

  • Page 63

    Pull the strap down and secure the small latch plate of the lap belt into the small buckle until you hear a “click”. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. When the belt is long enough to fit, insert the large latch plate into the buckle unti...

  • Page 64

    As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Seat belts in passenger seating positions the seat...

  • Page 65

    Anytime a child safety seat is installed in a seating position that has a belt with this feature. Children 12 years old and under should always be properly restrained in the rear seat. How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder por...

  • Page 66

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 67

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 68

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: for more information on properly adjusting and positi...

  • Page 69

    1 — downward movement 2 — rearward movement 3 — final downward movement to engage locking mechanism 2 things to know before starting your vehicle 67.

  • Page 70

    4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an autho...

  • Page 71

    Light remains illuminated until the respective seat belts are fastened. The driver should instruct all other occu- pants to fasten their seat belts. If a front seat belt is unbuckled while traveling at speeds greater than 5 mph (8 km/h), beltalert 威 will provide both audio and visual notification. T...

  • Page 72

    Seat belt extender if a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long...

  • Page 73

    Note: these air bags are certified to the new federal regulations for advanced air bags. The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver a...

  • Page 74

    This vehicle is equipped with supplemental seat- mounted side air bags (sab) to provide enhanced protection for an occupant during a side impact. The sabs are located in the outboard side of the front seats. Note: • air bag covers may not be obvious in the interior trim, but they will open during ai...

  • Page 75

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 76

    Supplemental seat-mounted side air bags (sab) supplemental seat-mounted side air bags (sab) may provide enhanced protection to help protect an occupant during a side impact. The sab is marked with an air bag label sewn into the outboard side of the front seats. When the air bag deploys, it opens the...

  • Page 77

    • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the sab and sabic air bags during deployment could cause you to be severely injured or killed. The system includes side impact sensors that are cali- brated to deploy the side...

  • Page 78

    Along with seat belts and pretensioners, advanced front air bags work with the supplemental driver side knee air bag and the passenger side knee bolster to provide improved protection for the driver and front passenger. Side air bags also work with seat belts to improve occupant protection. Air bag ...

  • Page 79

    Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all acci- dents, and also are needed to help keep you in position, away fr...

  • Page 80

    Warning! Ignoring the air bag warning light in your instru- ment panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have ...

  • Page 81

    Driver side knee air bag. The trim cover separates and folds out of the way allowing the air bag to inflate to the full size. The air bag fully inflates in about 15 to 20 milliseconds. The supplemental driver side knee air bag gas is vented through small vent holes in the side of the air bag. Supple...

  • Page 82

    Are not belted and seated properly, or if items are positioned in the area where the side curtain air bag inflates. This especially applies to children. The side curtain air bag is only about 3-1/2 in (9 cm) thick when it is inflated. Because air bag sensors estimate deceleration over time, vehicle ...

  • Page 83

    If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or al...

  • Page 84

    Warning! Deployed air bags and seat belt pretensioners can not protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retrac- tor assemblies replaced by an authorized dealer im- mediately. Also, have the occupant restraint con- troller (orc) system serv...

  • Page 85

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat includ- ing your trim cover and cushion...

  • Page 86

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of t...

  • Page 87

    To read data recorded by an edr, special equipment is required, and access to the vehicle or the edr is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. ...

  • Page 88

    The infant carrier is only used rearward-facing in the vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. Convertible child seats can be used either rearward- facing or forward-facing in the vehicle. Convertible child seats often hav...

  • Page 89

    In the vehicle by the lap/shoulder belt or the latch child restraint anchorage system. Refer to “lower an- chors and tether for children (latch)”. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s s...

  • Page 90

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • a rearward-facing child restraint shoul...

  • Page 91

    Installing the child restraint system we urge you to carefully follow the directions of the manufacturer when installing your child restraint. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector, and a means for adjusting the ...

  • Page 92

    Installing the latch-compatible child restraint system each vehicle, except commercial cargo vehicles, is equipped with the child restraint anchorage system called latch, which stands for lower anchors and tether for children. Two latch child restraint anchorage systems are installed on all second-r...

  • Page 93

    Installing the lower attachments: 1. The vehicle lower anchorages are round bars located at the rear of the seat cushion where it meets the seatback. 2. Loosen the adjusters on the lower child restraint attachment straps (reference the child restraint seat in- structions) to ease the installation. L...

  • Page 94

    Note: it is recommended to loosen the top tether strap and route it loosely prior to securing the lower anchors so the top tether strap is not trapped between the vehicle seat and child restraint. 3. Attach the lower child restraint attachment straps to the vehicle’s lower anchor bars. Ensure that t...

  • Page 95

    Rear seat tether strap mounting (second row anchorage shown) latch anchorages (third row 60/40 anchorage shown) 2 things to know before starting your vehicle 93.

  • Page 96

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Installing the child restraint using the vehicle seat belts the seat belts in...

  • Page 97

    Then allow the belt to retract into the retractor. As the belt retracts, you will hear a ratcheting sound. This indicates the safety belt is now in the automatic locking mode. 2. Finally, pull on any excess webbing to tighten the lap portion around the child restraint. Any seat belt system will loos...

  • Page 98

    Warning! Never carry a child in a rear facing infant carrier in a vehicle without rear seats. In an accident, serious injury or death may occur from the deploying pas- senger airbag. This vehicle is equipped with a child restraint tether anchor located on the lower rear of the front passenger seat. ...

  • Page 99

    Restraining infants and small children in commercial cargo vehicles there are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child: • the forward-facing child seat is for chi...

  • Page 100

    3. Route the tether strap under the head rest. Note: ensure that the child restraint tether strap is centered between the headrest supports underneath the head rest. 4. Using the hook attached to the child restraint tether strap, attach the child restraint tether strap to the metal anchor on the low...

  • Page 101

    While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving t...

  • Page 102

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), whi...

  • Page 103

    Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, ...

  • Page 104

    Floor mat safety information always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in o...

  • Page 105

    Warning! (continued) • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • if required, mounting posts must be properly installed, if not equipped...

  • Page 107: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ inside day/night mirror — if equipped . . . 112 ▫ automatic dimming mirror — if equipped . . 112 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . 113 ▫ driver’s au...

  • Page 108

    ▫ phone call features . . . . . . . . . . . . . . . . . . 135 ▫ uconnect™ phone features . . . . . . . . . . . . . 138 ▫ advanced phone connectivity . . . . . . . . . . . 142 ▫ things you should know about your uconnect™ phone . . . . . . . . . . . . . . . . . . . . 144 ▫ general information . . . ....

  • Page 109

    䡵 driver memory seat — if equipped . . . . . . . . 192 ▫ setting memory positions and linking rke transmitter to memory . . . . . . . . . . . . . . . . 192 ▫ easy entry/exit seat (available with memory seat only) . . . . . . . . . . . . . . . . . . . 195 䡵 to open and close the hood . . . . . . . . ...

  • Page 110

    ▫ rain sensing wipers — if equipped . . . . . . . 207 䡵 tilt/telescoping steering column . . . . . . . . . . 208 䡵 heated steering wheel — if equipped . . . . . . 209 䡵 adjustable pedals — if equipped . . . . . . . . . . 210 䡵 electronic speed control — if equipped . . . . . 212 ▫ to activate . . . ...

  • Page 111

    䡵 overhead consoles . . . . . . . . . . . . . . . . . . . . 227 ▫ front overhead console . . . . . . . . . . . . . . . 227 ▫ courtesy/interior lighting . . . . . . . . . . . . . 228 ▫ sunglass storage (non-sunroof only) . . . . . . 228 ▫ rear courtesy/reading lights — if equipped . . . . . . . . . ....

  • Page 112

    ▫ sunroof maintenance . . . . . . . . . . . . . . . . . 244 ▫ ignition off operation . . . . . . . . . . . . . . . . . 244 ▫ sunroof fully closed . . . . . . . . . . . . . . . . . . 244 䡵 electrical power outlets — if equipped . . . . . . 244 䡵 power inverter — if equipped . . . . . . . . . . . . 24...

  • Page 113

    ▫ super console — if equipped . . . . . . . . . . . 266 䡵 cargo area features . . . . . . . . . . . . . . . . . . . 268 ▫ rechargeable flashlight . . . . . . . . . . . . . . . . 268 䡵 rear window features . . . . . . . . . . . . . . . . . . 269 ▫ rear window defroster . . . . . . . . . . . . . . . ....

  • Page 114

    Mirrors inside day/night mirror — if equipped a two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (towa...

  • Page 115

    To the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. Note: this feature is disabled when the vehicle is moving in reverse. Caution! To avoid damage to the mirror during cleaning, never spray any cleani...

  • Page 116

    Warning! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are. Relying too much on side convex mirrors could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle...

  • Page 117

    The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a mirror, press either the l (left) or r (right) to select the mirror that you want to adjust. Note: a light in the selected button will illuminate indicating the mirror is activated and can ...

  • Page 118

    Tilt mirrors in reverse (available with memory seat only) — if equipped tilt mirrors in reverse provides automatic outside mirror positioning which will aid the drivers view of the ground rearward of the front doors. The driver’s outside mirror will move slightly downward from the present position w...

  • Page 119

    Blind spot monitoring — if equipped the blind spot monitoring (bsm) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle. Whe...

  • Page 120

    The bsm detection zone covers approximately one lane on both sides of the vehicle (11 ft or 3.35 m). The zone starts at the outside rear view mirror and extends ap- proximately 20 ft (6 m) to the rear of the vehicle. The bsm system monitors the detection zones on both sides of the vehicle when the v...

  • Page 121

    The bsm system notifies the driver of objects in the detection zones by illuminating the bsm warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “modes of operation” for further information. The bsm system monitors the...

  • Page 122

    Entering from the side vehicles that move into your adjacent lanes from either side of the vehicle. Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Side monitoring rear monitor...

  • Page 123

    Overtaking traffic if you pass another vehicle slowly (with a relative speed of less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km...

  • Page 124

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects t...

  • Page 125

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicle’s mirrors, glance over your shoulde...

  • Page 126

    Note: in a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When rcp is on and the vehicle is in reverse, the driver is alerted using both the visua...

  • Page 127

    Turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and de- tected object are present on the same side at the same time, both the visual and audio alerts will be issued. In addition to the au...

  • Page 128

    Phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s audio is transmitted through your vehi- cle’s audio system; the system will automatically mute your radio when using the uconnect™ phone. Note: the uconnect™ phone requires a mobile pho...

  • Page 129

    Warning! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in a collision causing serious injury or death. Uconnect™ phone button the radio or steering wheel con...

  • Page 130

    Operation voice commands can be used to operate the uconnect™ phone and to navigate through the uconnect™ phone menu structure. Voice commands are required after most uconnect™ phone prompts. You will be prompted for a specific command and then guided through the available options. • prior to giving...

  • Page 131

    Cancel command at any prompt, after the beep, you can say “cancel” and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (link) uconnect™ phone to a mobile phone to begin using your uconnect™ phone, you must pair your compatib...

  • Page 132

    Phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the uconnect™ phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at an...

  • Page 133

    Add names to your uconnect™ phonebook note: adding names to the uconnect™ phonebook is recommended when the vehicle is not in motion. • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook new entry”. • when prompted, say the name of the new entry. Use of long...

  • Page 134

    • to call a name from the uconnect™ phonebook or downloaded phonebook, follow the procedure in “call by saying a name” section. • automatic download and update, if supported, begins as soon as the bluetooth 威 wireless phone connection is made to the uconnect™ phone, for example, after you start the ...

  • Page 135

    • after the “ready” prompt and the following beep, say “phonebook edit entry”. • you will then be asked for the name of the phonebook entry that you wish to edit. • next, choose the number designation (home, work, mobile, or other) that you wish to edit. • when prompted, recite the new phone number ...

  • Page 136

    From the list, press the button while the uconnect™ phone is playing the desired entry and say “delete”. • after you enter the name, the uconnect™ phone will ask you which designation you wish to delete: home, work, mobile, other, or all. Say the designation you wish to delete. • note that only the ...

  • Page 137

    • to call one of the names in the list, press the button during the playing of the desired name, and say “call”. Note: the user can also exercise “edit” or “delete” operations at this point. • the uconnect™ phone will then prompt you as to the number designation you wish to call. • the selected numb...

  • Page 138

    When another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making a second call while current call is in progress to make a second call while you are currently on a call, press the button and say “dial” or “call” followed by the phone number or phonebook ent...

  • Page 139

    Call termination to end a call in progress, momentarily press the button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is ...

  • Page 140

    Uconnect™ phone features language selection to change the language that the uconnect™ phone is using: • press the button to begin. • after the “ready” prompt and the following beep, say the name of the language you wish to switch to english, espanol, or francais. • continue to follow the system prom...

  • Page 141

    Canada and 060 for mexico). The number dialed may not be applicable with the available mobile service and area. • if supported, this number may be programmable on some systems. To do this, press the button and say “setup”, followed by “emergency”. • the uconnect™ phone does slightly lower your chanc...

  • Page 142

    Paging to learn how to page, refer to “working with automated systems”. Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the uconnect™ phone. Voice mail calling to learn how to access your voice mail, refer to “working with automate...

  • Page 143

    The uconnect™ phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone. Note: • you may not hear all of the tones due to mobile phone network configurations. This is normal. • some paging and voice mail systems have system time out settings tha...

  • Page 144

    Dialing using the mobile phone keypad you can dial a phone number with your mobile phone keypad and still use the uconnect™ phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth 威 mobil...

  • Page 145

    From your uconnect™ phone paired mobile phone to the uconnect™ phone or vice versa, press the button and say “transfer call”. Connect or disconnect link between the uconnect™ phone and mobile phone your mobile phone can be paired with many different electronic devices, but can only be actively “conn...

  • Page 146

    • the selected phone will be used for the next phone call. If the selected phone is not available, the uconnect™ phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. Delete uconnect™ phone paired mobile phones • press the button to ...

  • Page 147

    You can either press the uconnect™ phone button to restore the factory setting or repeat the words and phrases when prompted by the uconnect™ phone. For best results, the voice training session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blow...

  • Page 148

    • fully closed windows, • dry weather condition. • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system such as voice mail, or when sending a page, at the...

  • Page 149

    • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect™ phone. • echo at the phone far end can sometimes be reduced by lowering the in-veh...

  • Page 150

    Send messages: you can send messages using uconnect™ phone. To send a new message: • press the button. • after the “ready” prompt and the following beep, say “sms send” or “send message.” • you can either say the message you wish to send or say “list messages.” there are 20 preset messages. To send ...

  • Page 151

    16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and th...

  • Page 152

    150 understanding the features of your vehicle.

  • Page 153

    3 understanding the features of your vehicle 151.

  • Page 154

    152 understanding the features of your vehicle.

  • Page 155

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 3 understa...

  • Page 156

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 157

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 158

    If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system is speaking is known as “barging in.” the system will be interrupted, and after the beep, you can add or chan...

  • Page 159

    3. Use the on/off volume rotary knob to adjust the volume to a comfortable level while the voice command system is speaking. Please note the volume setting for voice command is different than the audio system. Main menu start a dialogue by pressing the voice command button. You may say “main menu” t...

  • Page 160

    • “menu radio” (to switch to the radio menu) • “main menu” (to switch to the main menu) satellite radio to switch to satellite radio mode, say “sat” or “satellite radio”. In this mode, you may say the following com- mands: • “channel number” (to change the channel by its spoken number) • “next chann...

  • Page 161

    − “continue” (to continue recording) − “delete” (to delete the recording) • “play memos” (to play previously recorded memos) — during the playback you may press the voice command button to stop playing memos. You proceed by saying one of the following commands: − “repeat” (to repeat a memo) − “next”...

  • Page 162

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect™ voice “voice training” feature may be used. 1. Press the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your...

  • Page 163

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 164

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 165

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters in both the seat cushions and seatbacks. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- ha...

  • Page 166

    During a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further information. Front heated seats there are two heated seat switches that allow the driver and passenger to operate the seats independently. The controls for each heater ...

  • Page 167

    You can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high-level heating. Press the switch a second time to select low-l...

  • Page 168

    Manual front/second row seat adjuster both front seats are adjustable forward or rearward. The manual seat adjustment handle is located under the seat cushion at the front edge of each seat. While sitting in the seat, pull up on the handle and slide the seat forward or rearward. Release the bar once...

  • Page 169

    Manual reclining seats — if equipped for models equipped with manual reclining seats, the recline lever is located on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to ret...

  • Page 170

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 171

    For comfort the active head restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull outward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Push button activ...

  • Page 172

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 173

    Warning! (continued) • active head restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the ac- tive head restraint ensure that all cargo is se- cured, as loose cargo could contact the active head restraint during sudden st...

  • Page 174

    Head restraints — third row the head restraint in the center position can be raised and lowered for tether routing. Refer to “occupant re- straints” in “things to know before starting your ve- hicle” for further information. Stow ’n go 姞 seating — if equipped on vehicles equipped with stow ’n go 威 s...

  • Page 175

    5. Pull upward on the seatback recliner lever located on the outboard side of the seat. The non-adjustable head restraint and seatback will fold automatically during the seat tumble. No additional actuation is necessary. Seatback recliner lever, seat tumble, and head restraint fold lever non-adjusta...

  • Page 176

    The seat will automatically tumble into position for easy storage. 6. Push the seat into the storage bin. Automatic folding seatback tumbled second row seat 174 understanding the features of your vehicle.

  • Page 177

    7. Close the storage bin cover. Caution! The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. Warning! In a collision, serious injury could result if the seat storage bin covers are not properly latched. • d...

  • Page 178

    To unstow second row seats 1. Pull up on the storage bin latch to open the cover. 2. Pull up on the strap to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors. 3. Lift the seatback to the full upright position. 4. Return the head restraint to its upright posit...

  • Page 179

    3. Pull up on the seatback recliner lever on the outboard side of the seat to fold head rest and seatback and tumble seat forward. Easy entry second row the second row stow ’n go 威 seats allow easy entry to the third row seat or rear cargo area. Pull up on the seatback recliner lever on the outboard...

  • Page 180

    The seat will automatically fold into position for easy entry into the third row. Warning! In the event of a collision you could be injured if the seat is not fully latched. Quad seats — if equipped both quad seats are adjustable forward or rearward. The manual seat adjustment handle is located unde...

  • Page 181

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 182

    Fold-flat to fold the seat, lift the recliner lever to the full upward position and push the seatback forward until it rests on the seat cushion. Easy entry the quad seats can be tilted forward for easy entry into the third row. With the quad seat in the fold-flat position, lift up on the easy entry...

  • Page 183

    For passengers seated in the third row, there is a pull strap located on the outboard side of the seat near the bottom of the seat back. Third row passengers can pull on the strap and push the quad seat forward for folding the seatback and accessing the easy entry lever. To provide additional space ...

  • Page 184

    Pull out the retainer strap from the sewn-in pocket located on the base of the seat cushion. Place the strap around the grab handle located on the b-pillar. Before securing the strap, adjust the buckle for proper fit. Retainer strap b-pillar grab handle 182 understanding the features of your vehicle.

  • Page 185

    Secure the retainer strap to the inside grab handle located on the b-pillar. When not in use, store the strap in the sewn-in pocket located on the base of the seat cushion. Warning! To reduce the risk of personal injury: • retainer strap must always be securely attached to grab handle when seat is f...

  • Page 186

    Removal the quad seats can be removed if additional storage is needed. With the seat in the easy entry position, lift the cross beam forward and up to release the front anchor latches. Second row bench seat — if equipped while the bench seat does not stow in the floor, it is removable for added carg...

  • Page 187

    Release levers are located on the rear leg assemblies, near the floor. To remove the seat, squeeze each release handle and rotate downwards to deploy the wheels. A lock indicator button pops up when the seat is unlocked. The seat assembly can now be removed from the vehicle and moved on its easy out...

  • Page 188

    Third row power recline — if equipped the power recline feature, located on the side of the seat cushion, adjusts the seatback angle forward/rearward for occupant comfort. Third row power folding seat — if equipped a one-touch power folding seat switch is located in the left rear trim panel as part ...

  • Page 189

    The switch is only functional when the liftgate is open and the vehicle is in park. The rear switch bank allows multiple power folding and unfolding positions for the third row seats. Left and right third row seats can be folded individually or together. The third row power folding seat adjusts to t...

  • Page 190

    Note: • disconnect the center shoulder belt from the small buckle and lower the head restraints before attempting to fold/stow the power third row seats. • to abort seat operation while seat is in motion, press a different seat position selector switch to stop the seat. Once the seat stops moving, t...

  • Page 191

    3. Pull release strap marked “2” located on the rear of the seat to lower the seatback. 4. Pull release strap marked “3” to release the anchors. Release strap “2” release strap “3” 3 understanding the features of your vehicle 189.

  • Page 192

    5. Pull release strap marked “4” and tumble the seat rearward into the storage bin. To unfold third row seats 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. 2. Pull release strap marked “2” to unlock the recliner. Release str...

  • Page 193

    3. Pulling strap “4” releases the seatback to return to its full upright position. 4. Raise the head restraint to its upright position. Warning! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are f...

  • Page 194

    Driver memory seat — if equipped the memory buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. Your remote keyless entry (rke) transmitters can also be programm...

  • Page 195

    3. Adjust the driver’s seat, recliner, and driver’s side- view mirror to the desired positions. 4. Adjust the brake and accelerator pedals to the desired positions. 5. Turn on the radio and set the radio station presets (up to 10 am and 10 fm stations can be set). 6. Turn the ignition switch to the ...

  • Page 196

    To recall the memory settings for driver one, press memory button 1 on the driver’s door or the unlock button on the rke transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button 2 on the driver’s door or the unlock button on the rke transmitter linked...

  • Page 197

    Note: once programmed, all rke transmitters linked to memory can be easily enabled or disabled at one time. Refer to “electronic vehicle information center (evic)/ customer-programmable features ⬙ in “understanding your instrument panel” for further information. Easy entry/exit seat (available with ...

  • Page 198

    Note: the easy entry/easy exit feature can be en- abled or disabled through the programmable features in the electronic vehicle information center (evic). If your vehicle is not equipped with an evic, your dealership can activate/deactivate this feature for you. For details, refer to “electronic veh...

  • Page 199

    Use the hood prop rod to secure the hood in the open position. Safety lever location hood prop rod 3 understanding the features of your vehicle 197.

  • Page 200

    Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 12 in (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is fu...

  • Page 201

    Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Rotate the headlight switch to the second detent for headlight, parking light and instrument panel operation. Automatic headlights — if equipped this system automatically turns your head...

  • Page 202

    When exiting the vehicle the driver can choose to have the headlights remain on for 30, 60 or 90 seconds or not remain on. To change the timer setting, see your autho- rized dealer. The headlight delay time is programmable on vehicles equipped with an evic. Refer to “electronic vehicle information c...

  • Page 203

    Dimmer controls the dimmer switch is located next to the headlight switch. With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights. Interior lighting on rotate the left dimmer control completely upward to the second det...

  • Page 204

    Note: the key must be out of the ignition switch or the ignition switch must be in the off position for this feature to operate. Interior lighting off rotate the left dimmer control to the off position (extreme bottom). The interior lights will remain off when the doors or liftgate are open. Parade ...

  • Page 205

    Multifunction lever the multifunction lever is located on the left side of the steering column. The multifunction lever controls the: • turn signals • headlight beams low/high • flash-to-pass (optical horn) • front and rear wipers — washer functions turn signals move the multifunction lever up or do...

  • Page 206

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/low beam switch when the headlights are turned on, pushing the multi- function lever toward the instrument panel will switc...

  • Page 207

    Note: always remove any buildup of snow that pre- vents the windshield wiper blades from returning to the off position. If the windshield wiper switch is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. Warning! Sudden loss of visibility through the w...

  • Page 208

    • at driving speeds above 10 mph (16 km/h), the delay can be regulated from a maximum of approximately 18 second between cycles (first detent), to a cycle every one second (fifth detent). Windshield wiper operation rotate the end of the lever upward, to the first detent past the intermittent setting...

  • Page 209

    Rain sensing wipers — if equipped this feature senses moisture on the windshield and automatically activates the wipers for the driver. This feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of...

  • Page 210

    The rain sensing system has protective features for the wiper blades and arms. It will not operate under the following conditions: • low temperature wipe inhibit — the rain sensing feature will not operate when the ignition is first switched on, and the vehicle is stationary, and the outside tempera...

  • Page 211

    To unlock the steering column, push the lever downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in posi...

  • Page 212

    The heated steering wheel switch is located on the switch bank below the climate controls. Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on. Pressing the switch a second time will turn off the heated steering w...

  • Page 213

    From the driver to provide improved position with the steering wheel. The switch is located on the left side of the steering column. Press the switch forward to move the pedals forward (toward the front of the vehicle). Press the switch rearward to move the pedals rearward (toward the driver). • the...

  • Page 214

    Caution! Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path. Warning! Do not adjust the pedals while the vehicle is...

  • Page 215

    The same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off button and resetting the desired vehicle set speed. To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To turn t...

  • Page 216

    To resume speed to resume a previously set speed, push the res (+) button and release. Resume can be used at any speed above 20 mph (32 km/h). To vary the speed setting when the electronic speed control is set, you can in- crease speed by pushing the res (+) button. If the button is continually pres...

  • Page 217

    On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without electronic speed control. Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose cont...

  • Page 218

    Parksense 姞 sensors the four parksense 威 sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 in (30 cm) up to 79 in (200 cm) from the rear fascia/bumper in the horizontal di...

  • Page 219

    Parksense 姞 display when the vehicle is in reverse, the warning display will turn on indicating the system status. Park assist system on park assist system off 3 understanding the features of your vehicle 217.

  • Page 220

    The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the evic display will show fewer arcs and the sound tone will change from slow, to fast, to continuous. Slow tone fast tone 218 understanding th...

  • Page 221

    The vehicle is close to the obstacle when the evic display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: continuous tone 3 understanding the features of your vehicle 219.

  • Page 222

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none single 1/2 second tone slow fast continuous display message park assist system on warning object detected warning object de...

  • Page 223

    Shift lever is moved to reverse and the system is disabled, the evic will display the “park assist sys- tem off” message for as long as the vehicle is in reverse. Service the parksense 姞 rear park assist system when the parksense 威 rear park assist system is mal- functioning, the instrument cluster ...

  • Page 224

    • jackhammers, large trucks, and other vibrations could affect the performance of parksense 威. • when you turn parksense威 off, the instrument cluster will display “park assist system off.” further- more, once you turn parksense 威 off, it remains off until you turn it on again, even if you cycle the ...

  • Page 225

    Caution! • parksense威 is only a parking aid and it is unable to recognize every obstacle, including small ob- stacles. Parking curbs might be temporarily de- tected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • the vehic...

  • Page 226

    Warning! (continued) • before using the parksense威 rear park assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles becaus...

  • Page 227

    When displayed, static grid lines will illustrate the width of the vehicle while a dashed center-line will indicate the center of the vehicle to assist with aligning to a hitch/ receiver. The static grid lines will show separate zones that will help indicate the distance to the rear of the vehicle. ...

  • Page 228

    Warning! Drivers must be careful when backing up even when using the parkview 威 rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your...

  • Page 229

    4. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft-key. 5. Press the “save” soft-key. Turning parkview 姞 on or off — without navigation/multimedia radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Enable or disable the rear camera f...

  • Page 230

    Courtesy/interior lighting at the forward end of the console are two courtesy lights (standard dome light has two buttons). The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with remote keyless entry (rke) the lights will also turn on when th...

  • Page 231

    From this position, the door can be fully closed or, by rotating upward about 3/4 of the way and releasing, positioned for conversation mirror use. Note: from the “conversation mirror” position, the door can only be closed. To return to the full open position, the door must first be closed and then ...

  • Page 232

    Rear courtesy/reading lights — if equipped the overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with remote keyless entry (rke) the lights will also turn on when the unlock button on the rke ...

  • Page 233

    Rear console halo lighting the rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “lights/ halo lights — if equipped” in “understanding the fe...

  • Page 234

    The homelink 威 buttons, located on either the overhead console, headliner or sunvisor, designate the three differ- ent homelink 威 channels. The homelink威 indicator is located above the center button. Note: homelink 威 is disabled when the vehicle secu- rity alarm is active. Homelink 威 buttons/overhea...

  • Page 235

    Before you begin programming homelink 姞 be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the ...

  • Page 236

    Programming a rolling code for programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “learn” or “train” button located where the hanging antenna is attached to the garage door opener. It is not the button that is normally used to open...

  • Page 237

    3. Simultaneously press and hold both the homelink 威 button you want to program and the hand-held transmit- ter button. 4. Continue to hold both buttons and observe the indi- cator light. The homelink 威 indicator will flash slowly and then rapidly after homelink 威 has received the fre- quency signal...

  • Page 238

    2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “program- ming a rolling code” step 2 and follow all remaining steps. Programming a non-rolling code for programming gar...

  • Page 239

    Reprogramming a single homelink 威 button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the but...

  • Page 240

    4. Watch for the homelink 威 indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming. 5. Press and hold the programmed homelink 威 button and observe the indicator light. • if...

  • Page 241

    Security it is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The homelink 威 universal transceiver i...

  • Page 242

    Warning! • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” fea...

  • Page 243

    Power sunroof — if equipped the power sunroof switch is located between the sun visors on the overhead console. Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating t...

  • Page 244

    Opening sunroof — express press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- cally. This is called “express open”. During express open operation, any movement of the sunroof switch ...

  • Page 245

    Note: if three consecutive sunroof close attempts re- sult in pinch protect reversals, the fourth close attempt will be a manual close movement with pinch protect disabled. Pinch protect override if a known obstruction (ice, debris, etc.) prevents closing the sunroof, press the switch forward and ho...

  • Page 246

    Sunroof maintenance use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition off operation for vehicles not equipped with the electronic vehicle information center (evic), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the...

  • Page 247

    Note: to ensure proper operation a mopar 威 cigar knob and element must be used. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • power outlets are designed for a...

  • Page 248

    One outlet in the removable floor console (if equipped) shares a fuse with the lower outlet in the instrument panel and is also connected to the battery. Do not exceed a maximum power of 160 watts (13 amps) shared between the lower panel outlet and the removable floor console outlet. On vehicles equ...

  • Page 249

    The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both con- trolled by the ignition switch. Each of these outlets can support 160 watts (13 amps). Do not exceed 160 watts (13 amps) for each of these outlets. The power outlets include tethered cap...

  • Page 250

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 251

    Power inverter — if equipped a 110 volt, 150 watt inverter outlet (if equipped) converts dc current to ac current, and is located on the left rear trim panel immediately behind the second row left passenger seat. The power inverter switch is located on the instrument panel below the climate controls...

  • Page 252

    To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. Cupholders there are cupholders located throughout the interior. All liners are removable for cleaning. Pull the flexible liner from the cupholder drawer or tray starting at one edge for easy...

  • Page 253

    Super console — if equipped on models equipped with the super console, there are two cupholders located in the center of the console. For rear passengers two cupholders are located in the pull-out drawer, located in the back of the super console. Pull the drawer out to the first position to use the ...

  • Page 254

    Premium console cupholders — if equipped on models equipped with premium center consoles, there are four cupholders located on the top of the console. Interior bottle holders there are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels,...

  • Page 255

    Two outboard mesh pockets are on intermediate seating. The mesh pockets are flexible enough to hold juice boxes, toys, games or mp3 players, etc. Smoker’s package kit — if equipped with the optional authorized dealer-installed smoker’s package kit, a removable ash receiver is inserted into one of th...

  • Page 256

    Storage glove compartments upper and lower glove compartments are located on the passenger side of the instrument panel. Upper glove compartment to open the upper compartment, press in on the button, located on the left side of the upper door. The door will automatically open. To close the compartme...

  • Page 257

    Lower glove compartment to open the lower compartment pull out on the release handle. Note: the lower compartment is equipped with a lock that is part of the compartment handle. Door trim panel storage front door storage both interior front door panels have multiple pockets for storage. Lower compar...

  • Page 258

    Driver seatback storage — if equipped the driver’s seatback has a primary storage pocket on all models and an optional secondary mesh pocket. Umbrella holder an umbrella holder has been conveniently molded into the left front door entry scuff molding. Driver’s seatback storage 1 — bag holder 2 — sta...

  • Page 259

    Second row seat storage bins — if equipped the seat storage bins are located on the floor in front of the second row seats. The area below the covers can be used for storage when the second row seat is in the upright position. Pull up on the storage bin latch to open the cover. Slide the storage bin...

  • Page 260

    Warning! In a collision, serious injury could result if the seat storage bin covers are not properly latched. • do not drive the vehicle with the storage bin covers open. • keep the storage bin covers closed and latched while the vehicle is in motion. • do not use a storage bin latch as a tie down. ...

  • Page 261

    Caution! The storage bin cover must be flat and locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. Seat storage bin cover emergency release lever as a security measure, your vehicle may be built with a storage bin cover emergency release is bui...

  • Page 262

    Coat hooks coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle. Cargo area storage the liftgate sill plate has a ra...

  • Page 263

    Console features there are three consoles available: basic, premium and super. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while ...

  • Page 264

    To reinstall the basic floor console 1. Position the console at a slight angle (front slightly higher than the rear). 2. Slide the console rearward into the floor bracket/ hook. 3. Align the console until the front anchor cup plug hole is centered on the winch hole. 4. Reinstall the clip first and t...

  • Page 265

    • large console center storage will store headphones for the available rear dvd entertainment system or other items • 12 volt dc power outlet provides continuous power inside the console for cell phones or other electronics. • rear occupant accessible • multiple adjustments • removable from vehicle ...

  • Page 266

    Position 2 shows the raised storage tray revealing a large storage area below. Dual storage bins position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console. This provides easy access to the storage area bel...

  • Page 267

    To remove the premium floor console 1. Pull up on the bottom release handle in the front of the console. 2. Lift the rear of the console up several inches/ centimeters. 3. Pull rearward to disengage from floor and remove console. To reinstall the console: 1. Position the console at a slight angle (r...

  • Page 268

    Warning! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. Super console — if equipped the super console contains multiple storage areas, front lower pass through, top forward bin, top re...

  • Page 269

    Note: the front cupholder light ring and pass through lighting is controlled by a dimming switch located on the instrument panel, refer to “lights” in “understanding the features of your vehicle” for further information. Located in the back of the super console is a storage drawer and cupholders for...

  • Page 270

    Cargo area features rechargeable flashlight the rechargeable flashlight is mounted on the right side of the cargo area. The flashlight snaps out of the bezel when needed. The flashlight features two bright led light bulbs and is powered by a lithium battery that recharges when snapped back into plac...

  • Page 271

    Rear window features rear window defroster the rear window defroster button is located on the climate control (mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is...

  • Page 272

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 273

    Roof luggage rack — if equipped the crossbars on your vehicle are delivered stowed within the roof rack side rails. If adding cargo, deploy the crossbars. Distribute cargo weight evenly on the roof rack crossbars, to maximum of 150 lbs (68 kg). The roof rack does not increase the total load carrying...

  • Page 274

    Note: • crossbars are error-proofed and cannot be deployed or stowed in the incorrect positions. • to help control wind noise, stow the crossbars in the side rails when they are not in use. Deploying the crossbars to deploy the crossbars, completely loosen the thumb screws at both ends of the crossb...

  • Page 275

    Bend the crossbar supports at each end, taking care to keep hand clear of pivoting joint. Slide the thumb screw down. Then, position the crossbars across the roof. Stowed position deployed position 3 understanding the features of your vehicle 273.

  • Page 276

    Note: the crossbars are identical and can be placed in any two of the three deploy positions. Make sure the directional arrows on the crossbars align with the directional arrows on the side rails. Set the crossbars into the deployed positions. Once the crossbars are set into position, tighten the th...

  • Page 277

    Stowing the crossbars reverse the procedure to stow the crossbars, again, taking care to keep hand clear of pivoting joint. Crossbars are identical and can be stowed in either rail nest. Once the crossbars are stowed, tighten the thumb screws completely. Note: load should always be secured to crossb...

  • Page 278

    Caution! • check deployed crossbars frequently and re- tighten thumb screws as necessary. • to avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropri- ately. • t...

  • Page 279

    Warning! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack cautions when carrying cargo on your roof rack. Sun screens — if equipped sun scree...

  • Page 280

    Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window. To lower the sun screen, gently lift the tab upward to disengage the hooks, and feed the screen back into the base sill. Sun screen extended 278 understa...

  • Page 281: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 283 䡵 instrument cluster — base . . . . . . . . . . . . . . . 284 䡵 instrument cluster — premium . . . . . . . . . . . 285 䡵 instrument cluster descriptions . . . . . . . . . . . 286 䡵 electronic v...

  • Page 282

    ▫ messages # . . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ compass / temperature display . . . . . . . . . 313 ▫ customer-programmable features (system setup) . . . . . . . . . . . . . . . . . . . . . . 315 䡵 media center 730n/430/430n (rhr/rer/ rbz/rhb) cd/dvd/hdd/nav — if equipped . . . ...

  • Page 283

    䡵 ipod威/usb/mp3 control — if equipped . . . . . 346 ▫ connecting the ipod威 or external usb device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347 ▫ using this feature . . . . . . . . . . . . . . . . . . . 348 ▫ controlling the ipod威 or external usb device using radio buttons . . . . . . ...

  • Page 284

    ▫ replacing the remote control batteries . . . . 372 ▫ headphones operation . . . . . . . . . . . . . . . . 372 ▫ controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 ▫ replacing the headphone batteries . . . . . . . 374 ▫ unwired威 stereo headphone lifetime limited warranty . . . . . ....

  • Page 285

    Instrument panel features 1 — air vents 5 — upper glove compartment 9 — storage bin 13 — hood release 2 — instrument cluster 6 — lower glove compartment 10 — cup holders 14 — dimmer switch 3 — shift lever 7 — climate controls 11 — switch bank 15 — headlight switch 4 — radio 8 — dvd – if equipped 12 ...

  • Page 286

    Instrument cluster — base 284 understanding your instrument panel.

  • Page 287

    Instrument cluster — premium 4 understanding your instrument panel 285.

  • Page 288

    Instrument cluster descriptions 1. Tachometer the red segments indicate the maximum permissible engine revolutions per minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 2. Front fog light indicator — if equipped this indicator will illuminate when the...

  • Page 289

    Odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repai...

  • Page 290

    Low tire when the appropriate condition exists, the odometer display will toggle between low and tire for three cycles. Gascap if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will display in the odometer display area...

  • Page 291

    2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates when you start the engine, the oil change indicator system did not reset. If necessary, repeat these steps. Electronic vehic...

  • Page 292

    Vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) as an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more of your ...

  • Page 293

    Tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the tpms to continue to function properly. Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped...

  • Page 294

    Caution! Prolonged driving with the mil on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warning! A malfunctioning catalytic ...

  • Page 295

    • each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation...

  • Page 296

    16. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: • you must apply the brakes before shifting from park. • the highest available transmission gear is displayed in the lower right cor...

  • Page 297

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 298

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 19. Seat belt reminder light when the ignition switch is first turned to o...

  • Page 299

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see “main- taining your vehicle”. Follow the warni...

  • Page 300

    24. Engine temperature warning light this light warns of an overheated engine condi- tion. As engine coolant temperatures rise and the gauge approaches h , this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the tempera- ture ga...

  • Page 301

    26. Transmission temperature warning light during sustained high speed driving or trailer towing up long grades on hot days, the auto- matic transmission oil may become too hot. When the transmission overheat warning light turns on, you will experience reduced vehicle perfor- mance until the automat...

  • Page 302

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. This system conveniently allows the driver to select a variety of useful information by pressing the switches...

  • Page 303

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: up button press and release the up button to scroll up- ward through the main menus (fuel economy, vehicle info, tire psi, cruise, messages, units, system setup) and sub-menus. Down bu...

  • Page 304

    Back button press the back button to scroll back to a previous menu or sub-menu. Electronic vehicle information center (evic) displays the evic display consists of three sections: 1. The top line where compass direction, odometer line and outside temperature are displayed. 2. The main display area w...

  • Page 305

    • unstored messages this message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are ⬙turn signal on⬙ (if a turn signal is left on) and ⬙lights on⬙ (if driver leaves the vehicle). • unstored messages until run these messages ...

  • Page 306

    • damaged key • key not programmed • vehicle not in park • press brake pedal and push button to start • door(s) ajar (with a single chime, if vehicle is in motion) • liftgate ajar (chime will sound when vehicle starts moving) • low tire pressure • service tpm system (refer to “tire pressure monitor-...

  • Page 307

    • blind spot system not available — this message is displayed to indicate the blind spot monitor (bsm) system is temporarily unavailable due to sensor block- age, electronic interference, or other ⬙temporary⬙ con- ditions. When this message is displayed both outside rear view icons will be illuminat...

  • Page 308

    • electronic speed control set this light will turn on when the electronic speed control is set. For further information, refer to “electronic speed control” in “under- standing the features of your vehicle.” evic amber telltale lights this area will show reconfigurable amber caution tell- tales. Th...

  • Page 309

    • oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on....

  • Page 310

    If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough ...

  • Page 311

    Warning! If the transmission temperature warning light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. Oil change required your vehicle is equipped with an eng...

  • Page 312

    Fuel economy press and release the up or down button until “fuel economy” displays highlighted in the evic and press the select button. The following fuel economy func- tions display in the evic: • average fuel economy (avg) • distance to empty (dte) • miles per gallon (mpg) average fuel economy thi...

  • Page 313

    Note: significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the dte displayed value. When the dte value is less than 30 miles (48 km) estimated driving distance, the dte display will change to a “low fuel” message. This...

  • Page 314

    Trip b shows the total distance traveled for trip b since the last reset. Elapsed time shows the total elapsed time of travel since the last reset when the ignition switch is in the acc position. Elapsed time will increment when the ignition switch is in the on or start position. To reset a trip fun...

  • Page 315

    • oil temperature displays the actual oil temperature. • oil pressure displays the actual oil pressure. • engine hours displays the number of hours of engine operation. Messages # select from main menu using the up or down buttons. This feature shows the number of stored warning mes- sages (in the #...

  • Page 316

    Metallic objects) until the cal indicator displayed in the evic turns off. The compass will now function normally. Note: a good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Manual compas...

  • Page 317

    Note: keep magnetic materials away from the top of the instrument panel, such as ipod’s, mobile phones, laptops and radar detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. 1. Turn the ignition switch on. 2. ...

  • Page 318

    Press and release the up or down button until ⬙system setup ⬙ is highlighted in the main menu of the evic. Then press the select button to enter the system setup sub-menu. Press and release the up or down button to select a feature form the following choices: language when in this display you may se...

  • Page 319

    Auto unlock doors when on is selected, all doors will unlock when the vehicle is stopped and the transmission is in the park or neutral position and the driver’s door is opened. To make your selection, press and release the select button until a check-mark appears next to the feature showing the sys...

  • Page 320

    In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These features will stay on through the duration of remote start or until the key is turned to run. To make your selection, press and release the select button until a check-mark appears ne...

  • Page 321

    Headlamps with wipers (available with auto headlights only) when on is selected, and the headlight switch is in the auto position, the headlights will turn on approxi- mately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turn...

  • Page 322

    Illuminated approach when this feature is selected, the headlights will activate and remain on for up to 90 seconds when the doors are unlocked with the rke transmitter. To make your selec- tion, scroll up or down until the preferred setting is highlighted, then press and release the select button u...

  • Page 323

    To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Blind spot alert there are three selections when operating blind spot alert (“blind s...

  • Page 324

    Media center 730n/430/430n (rhr/rer/rbz/ rhb) cd/dvd/hdd/nav — if equipped note: the sales code is located on the lower right side of the unit’s faceplate. Refer to your uconnect™ multimedia rhr, rer, rbz or rhb user’s manual for detailed operating instructions. Operating instructions (voice command...

  • Page 325

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 326

    4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the ...

  • Page 327

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button press the buttons to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button...

  • Page 328

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 329

    If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ejecting with the ignition off is not allowed on convertible or soft-...

  • Page 330

    Notes on playing mp3 files the radio can play mp3 files; however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw...

  • Page 331

    Discs created with an option such as ⬙keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for cd audio or mp3 playback may result in longer disc loading times. Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 file...

  • Page 332

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 333

    Media center 130 with satellite radio (sales code res+rsc) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rota...

  • Page 334

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice command system (radio) — if equipped refer to “voice command” in the uconnect™ user ma...

  • Page 335

    3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob or wait fi...

  • Page 336

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 337

    Program type 16-digit character display information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports spor...

  • Page 338

    Hours, press the tune/scroll control knob to set the minutes. The minutes will begin to blink. Adjust the minutes using the right side tune/scroll control knob. Press the tune/scroll control knob to save time change. Am/fm button press the button to select either am or fm mode. Set/rnd button — to s...

  • Page 339

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on/run or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks a...

  • Page 340

    If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ejecting with the ignition off is not allowed on convertible or soft-...

  • Page 341

    Notes on playing mp3 files the radio can play mp3 files; however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw...

  • Page 342

    Discs created with an option such as ⬙keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for cd audio or mp3 playback may result in longer disc loading times. Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 file...

  • Page 343

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 344

    Press and hold the info button again for three seconds to return to ⬙elapsed time⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or cassette player and utilize the vehicle’s au...

  • Page 345

    Radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www- .Siriuscanada.Ca for ...

  • Page 346

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 347

    Additional three seconds will make the radio display the song title all of the time (press and hold again to return to normal display). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) tu...

  • Page 348

    Set button – to set the pushbutton memory when you are receiving a channel that you wish to commit to pushbutton memory, press the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a butt...

  • Page 349

    This feature allows an ipod 威 or external usb device to be plugged into the usb port, located in the glove compart- ment. Ipod 威 control supports mini, 4g, photo, nano, 5g ipod威 and iphone 威 devices. Some ipod威 software versions may not fully support the ipod 威 control features. Please visit apple’s...

  • Page 350

    Note: the glove compartment will have a position where the ipod 威 or consumer electronic audio device cable can be routed through without damaging the cable when closing the lid. This allows routing of the cable without damaging it while closing the lid. If a cut out is not available in the glove co...

  • Page 351

    Control mode, audio tracks (if available from audio device) start playing over the vehicle’s audio system. Play mode when switched to ipod 威/usb/mp3 control mode, the ipod 威 or external usb device automatically starts play mode. In play mode, the following buttons on the radio faceplate may be used ...

  • Page 352

    To the next screen of data for that track. Once all screens have been viewed, the last info button press will go back to the play mode screen on the radio. • pressing the repeat button will change the audio device mode to repeat the current playing track or press the vr button and say ⬙repeat on⬙ or...

  • Page 353

    Fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on the radio display may be noticeable. • during all list modes, the ipod威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backward (co...

  • Page 354

    Caution! • leaving the ipod威 or external usb device (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufactur- er’s guidelines. • placing items on the ipod威 or external usb device, or connections to the ipod 威...

  • Page 355

    2. After the ⬙ready⬙ prompt and the following beep, say ⬙setup⬙, then ⬙select audio devices⬙. 3. Say the name of the audio device or ask the uconnect™ phone system to list audio devices. Next track use the seek up button, or press the vr button on the radio and say “next track” to jump to the next t...

  • Page 356

    • cycle the ignition to the on or acc position. • turn on the ves™ player (if equipped on dual screen system) by pushing the power button, located on the far left, or by pressing the button on the remote control. • when the video screen(s) are open and a dvd is inserted into the ves™ player, the scr...

  • Page 357

    When connecting an external source to the aux input, be sure to follow the standard color coding for the ves™ jacks: note: certain high-end video games, such as playsta- tion3 and xbox360 will exceed the power limit of the vehicle’s power inverter. Refer to the power inverter section in your vehicle...

  • Page 358

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 soft-key and then touch eithe...

  • Page 359

    Listen to an audio source on channel 2 while a video is playing on channel 1 ensure the remote control and headphone switch is on channel 2. Using the remote control 1. Press the mode button on the remote control and the mode select screen will display, unless a video is playing then only a small ba...

  • Page 360

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. To listen to an audio source on channel 2...

  • Page 361

    Dual video screen note: typically there are two different ways to operate the features of the video entertainment system (ves)™. • the remote control • the touch-screen radio (if equipped) play a dvd using the touch-screen radio 1. Press the open/close or load hard-key on the radio faceplate (touch-...

  • Page 362

    Using the remote control 1. Press the mode button on the remote control. 2. While looking at screen 1 or 2, highlight disc by either pressing up/down/left/right buttons or by re- peatedly pressing the mode button, then press enter. Note: • channel/screen 1 select mode information is shown on the lef...

  • Page 363

    3. Touch the 1 or 2 soft-key based on the channel you want to change and then the disc soft-key in the media column. To exit touch the back arrow at the top left of the screen. Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key...

  • Page 364

    • viewing a dvd on the touch-screen radio screen is not available in all states/provinces, and the vehicle must be stopped, and the shift lever must be in the park position for vehicles with automatic transmis- sion. In vehicles with manual transmission the parking brake must be engaged. • touching ...

  • Page 365

    Using the remote control 1. Press the mode button on the remote control. 2. While looking at screen 1 or 2, highlight ves disc by either pressing up/down/left/right buttons or by re- peatedly pressing the mode button, then press enter on the remote control. Note: • channel/screen 1 select mode infor...

  • Page 366

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, touch the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 or 2 soft-key and then the di...

  • Page 367

    • viewing a dvd on the touch-screen radio screen is not available in all states/provinces, and the vehicle must be stopped, and the shift lever must be in the park position for vehicles with automatic transmis- sion. In vehicles with manual transmission the parking brake must be engaged. Listen to a...

  • Page 368

    Using the touch screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, touch the hide list soft-key to display the rear ves controls screen. 3. To listen to an audio source on channel 1...

  • Page 369

    Third row swivel screen (if equipped) • the third row screen or screen 2 has the ability to lower and swivel to face forward. • while the swivel screen is facing forward, the second row screen or screen 1 must be fully open in order for the swivel screen (screen 2) to work. Select channel/screen 2 a...

  • Page 370

    Important notes for dual video screen system • ves is able to transmit two channels of stereo audio and video simultaneously. • in split screen mode the left side equates to channel 1 and the right side equates to channel 2. • selecting a video source on channel 1, the video source will display on t...

  • Page 371

    2. Channel selector indicators – when a button is pressed, the currently affected channel or channel button is illuminated momentarily. 3. Light – turns the remote control backlighting on or off. The remote backlighting turns off automatically after five seconds. 4. Channel/screen selector switch - ...

  • Page 372

    Disc in a radio with a multiple-disc changer, prog up selects the next disc and prog down selects the previ- ous disc. 11. Mute – press to mute the headphone audio output for the selected channel. 12. Slow – press to slow playback of a dvd disc. Press play ( 䉴) to resume normal play. 13. Status – pr...

  • Page 373

    Remote control storage the video screen(s) come with a built in storage compart- ment for the remote control which is accessible when the screen is opened. To remove the remote, use your index finger to pull and rotate the remote towards you. Do not try to pull the remote straight down as it will be...

  • Page 374

    Dvd player, follow the radio’s instructions to turn video lock on. The radio and the video screen(s) indicate when video lock is active. • pressing the video lock again or turning the ignition off turns video lock off and allows remote control operation of the ves™. Replacing the remote control batt...

  • Page 375

    Controls the headphone power indicator and controls are located on the right ear cup. Note: the rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video sys...

  • Page 376

    • when both switches are on channel 2, the remote is controlling channel 2 and the headphones are tuned to the audio of the ves™ channel 2. 2. Press the mode button on the remote control. 3. If the video screen is displaying a video source (such as a dvd video), pressing status shows the status on a...

  • Page 377

    How long does the coverage last? This warranty lasts as long as you own the product. What does this warranty cover? Except as specified below, this warranty covers any product that in normal use is defective in workmanship or materials. What does this warranty not cover? This warranty does not cover...

  • Page 378

    You may register your unwired 威 wireless headphones online at www.Unwiredtechnology.Com or by phone at 1-888-293-3332. System information shared modes this allows the ves™ to output radio sources to the headphones and the radio to output ves™ sources to the vehicle speakers. When the radio and ves™ ...

  • Page 379

    Information mode display 1. Channel 1 mode 2. Channel 1 shared status 3. Channel 1 audio only/mute 4. Channel 2 mode 5. Channel 2 shared status 6. Channel 2 audio only/mute 7. Channel 1 enter button action 8. Channel 2 enter button action 9. Clock 10. Video lock 11. Not available / error 12. Disc ch...

  • Page 380

    Numeric keypad menu when the display for either channel 1 or channel 2 shows direct tune, pressing the remote control’s enter button activates a numeric keypad menu. This screen makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Pres...

  • Page 381

    Press the remote control’s enter button to tune to that station. To jump through the list more quickly, navigate to the page up and page down icons on the screen. Disc menu when listening to a cd audio or cd data disc, pressing the remote control’s menu button displays a list of all commands which c...

  • Page 382

    Control’s setup button activates the display settings menu. These settings control the appearance of the video on the screen. The factory default settings are already set for optimum viewing, so there is no need to change these settings under normal circumstances. To change the settings, press the r...

  • Page 383

    If the screen is closed and there is no audio heard, verify that the headphones are turned on (the on indicator is illuminated) and the headphone selector switch is on the desired channel. If the headphones are turned on, press the remote control’s power button to turn audio on. If audio is still no...

  • Page 384

    Recorded discs the ves™ dvd player will play cd-r and cd-rw discs recorded in cd-audio or video-cd format, or as a cd-rom containing mp3 or wma files. The player will also play dvd-video content recorded to a dvd-r or dvd-rw disc. Dvd-rom discs (either pressed or re- corded) are not supported. If yo...

  • Page 385

    The recommended method for labeling recordable discs (cd-r, cd-rw, and dvd-r) is with a permanent marker. Do not use adhesive labels as they may separate from the disc, become stuck, and cause permanent damage to the dvd player. Compressed audio files (mp3 and wma) the dvd player is capable of playi...

  • Page 386

    • to change the current directory, use the remote con- trol’s prog up and down buttons. Disc errors if the dvd player is unable to read the disc, a ⬙disc error⬙ message is displayed on the ves™ and radio displays and the disc is automatically ejected. A dirty, damaged, or incompatible disc format ar...

  • Page 387

    Display other language setup all of the language settings have a special ⬙other⬙ setting to accommodate languages other than japanese or eng- lish. These languages are selected using a special four- digit code. To enter a new language code, activate the dvd setup menu. To enter dvd setup menu stop t...

  • Page 388

    • using the remote control up and down cursor but- tons, select a digit for the current position. After selecting the digit, press the remote control’s right cursor button to select the next digit. Repeat this digit selection sequence for all four digits. • when the entire four-digit code is entered...

  • Page 389

    The default rating is level 8 (play all discs without a password) and the default password is 0000. To set the password, activate the dvd setup menu and follow these additional instructions: • using the remote control left and right cursor but- tons, select the rating tab. • highlight ⬙change passwo...

  • Page 390

    • using the remote control’s up and down cursor buttons to set the value for the current digit and the remote control’s right cursor button to select digits, enter the new password. • after the four-digit password is entered, press the remote control’s enter button to accept the change. Dvd player l...

  • Page 391

    To set the rating, activate the dvd setup menu and follow these additional instructions: • using the remote control’s left and right cursor buttons, select the rating tab. • highlight ⬙change rating⬙, and then press the remote control’s enter button. • enter the current password. Select a digit, use...

  • Page 392

    General information this system complies with part 15 of the fcc operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Steering wheel au...

  • Page 393

    The right-hand rocker switch has a pushbutton in the center, and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume. Pressing the bottom of the rocker switch will decrease the volume. Pressing the center button changes the operation of th...

  • Page 394

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 395

    Climate controls the climate control system allows you to regulate the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, below the radio. Manual heating and air conditioning system — if equipped the controls for the manual...

  • Page 396

    1. Left front temperature control provides left front seat occupant with independent tem- perature control. Turn left for cooler or right for warmer temperature settings. 2. Rear blower control — if equipped use this control to regulate the amount of air forced through the rear system in any mode yo...

  • Page 397

    7. Front defrost mode air is directed through the windshield and side window demist outlets. Use defrost mode with maximum blower and temperature settings for best windshield and side window defrosting. Note: the air conditioning compressor may operate in mix and defrost, or a blend of these modes e...

  • Page 398

    Caution! (continued) • do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • keep all objects a safe distance from the window. 9. Recirculation control button press this button to choose between outside air intake or recirculation of the air i...

  • Page 399

    • in order to prevent fogging, when the recirculation button is pressed and the mode control is set to panel, the a/c will engage automatically. • the a/c can be deselected manually without disturb- ing the mode control selection. 10. Air conditioning (a/c) button press and release to change the cur...

  • Page 400

    Note: for maximum airflow to the rear, the center instrument panel outlets can be directed toward the rear seat passengers. Economy mode if economy mode is desired, press the a/c button to turn off the indicator light and the a/c compressor. Rotate the temperature control knob to the desired tempera...

  • Page 401

    Rear blower control the primary control for the rear blower is on the front climate control unit, located on the instrument panel. Only when the front control for the rear blower is in the rear position do the second row seat occupants have control of the rear blower speed. The rear blower control, ...

  • Page 402

    When rear controls are locked by the front system, the lock symbol on the temperature knob is illuminated, and the rear overhead adjustments are inoperable. Rear mode control headliner mode air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the ...

  • Page 403

    The three-zone atc system automatically maintains the interior comfort level desired by the driver and all passen- gers. The system automatically adjusts the air temperature, the airflow volume, amount of outside air recirculation and the airflow direction. This maintains a comfortable tem- perature...

  • Page 404

    7. Right front seat occupant temperature display this display shows the temperature setting for the right front seat occupant. 8. Front defrost button press and release to change the current setting, the indicator illuminates when on. Performing this function will cause the atc to switch into manual...

  • Page 405

    15. Mode control button press and release to select between modes (panel, bi- level, floor, mix). Performing this function will cause the atc to switch into manual mode. 16. Recirculation control button press and release to change the current setting, the indicator illuminates when on. 17. Sync butt...

  • Page 406

    1. Mode display this display shows the current mode selection. 2. Rear temperature display this display shows the temperature setting for the rear seat occupants. 3. Blower control display this display shows the current blower speed selection. 4. Rear auto indicator this indicates when the system is...

  • Page 407

    Customer-programmable feature. Refer to the “elec- tronic vehicle information center (evic) — customer- programmable features” in this section. To provide you with maximum comfort in the automatic mode, during cold start-ups, the blower fan will remain on low until the engine warms up. The fan will ...

  • Page 408

    Panel mode air is directed through the outlets in the instrument panel. These outlets can be adjusted for direction, and turned on or off to control airflow. Note: for maximum airflow to the rear, the center instrument panel outlets can be directed toward the rear seat passengers. Bi-level mode air ...

  • Page 409

    Air conditioning (a/c) the air conditioning (a/c) button allows the operator to manually activate or deactivate the air conditioning system. When in a/c mode and the atc is set to a cool temperature, dehumidified air flows through the air outlets. If economy mode is desired, press the a/c button to ...

  • Page 410

    Rear automatic temperature control (atc) — if equipped the rear atc system has floor air outlets at the rear of the right side sliding door, and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the hea...

  • Page 411

    1. Press the rear temperature lock button on the front atc panel. This turns off the rear temperature lock icon in the rear temperature knob. 2. Rotate the rear blower, rear temperature and the rear mode control knobs to suit your comfort needs. 3. Atc is selected by adjusting the rear blower knob c...

  • Page 412

    Rear blower control the rear blower control knob can be manually set to off, or any fixed blower speed, by rotating the knob from low to high. This allows the rear seat occupants to control the volume of air circulated in the rear of the vehicle. Caution! Interior air enters the rear automatic tempe...

  • Page 413

    Headliner mode air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vanes of the outlets to one side will shut off the airflow. Bi-level mode air comes from both the headliner outlets and the floor outlets. Note: in...

  • Page 414

    Vacation/storage before you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes, in fresh air with the blower setting on high. This will ensure adequate system lubrication to minimize the possibility of ...

  • Page 415

    Operating tips a/c air filter on vehicles equipped with automatic temperature con- trol (atc), the climate control system filters out dust and pollen from the air. Refer to “air conditioning” in “maintaining your vehicle” for filter replacement instructions. 4 understanding your instrument panel 413.

  • Page 417: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 419 ▫ automatic transmission . . . . . . . . . . . . . . . 419 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 419 ▫ extreme cold weather (below –20°f or –29°c) . . . . . . . . . . . . . . . . 4...

  • Page 418

    䡵 driving through water . . . . . . . . . . . . . . . . . 435 ▫ flowing/rising water . . . . . . . . . . . . . . . . . 435 ▫ shallow standing water . . . . . . . . . . . . . . . 436 䡵 power steering . . . . . . . . . . . . . . . . . . . . . . . 437 ▫ power steering fluid check . . . . . . . . . . . ...

  • Page 419

    ▫ full size spare – if equipped . . . . . . . . . . . . 466 ▫ limited-use spare – if equipped . . . . . . . . . 466 ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . 467 ▫ tread wear indicators . . . . . . . . . . . . . . . . . 468 ▫ life of tire . . . . . . . . . . . . . . . . . . . . ....

  • Page 420

    ▫ selection of engine oil for flexible fuel vehicles (e-85) and gasoline vehicles . . . . . . 489 ▫ starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 489 ▫ cruising range . . . . . . . . . . . . . . . . . . . . . . 489 ▫ replacement parts . . . . . . . . . . . . . . . . . . . 490 ▫ main...

  • Page 421

    Starting procedures before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your ve...

  • Page 422

    3. If the engine fails to start, the starter will disengage automatically in 10 seconds. If this occurs, turn the ignition switch to the off position, wait 10 to 15 seconds, then repeat the “normal starting” procedure (steps 1–3 above). Note: this vehicle is equipped with a transmission shift interl...

  • Page 423

    Warning! (continued) • if the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly. Refer to “jump starting” in “what to do in emergen- cies” for further informa...

  • Page 424

    After starting the idle speed will automatically decrease as the engine warms up. Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire exten...

  • Page 425

    Caution! (continued) • do not move the shift lever between park, re- verse, neutral, or drive when the engine is above idle speed. • before moving the shift lever into any gear, make sure your foot is firmly pressing the brake pedal. Note: you must press and hold the brake pedal down while shifting ...

  • Page 426

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, and remove the key fob. On...

  • Page 427

    Fuel economy (econ) mode the fuel economy (econ) mode can improve the vehi- cle’s overall fuel economy during normal driving condi- tions. Press the “econ” switch in the center stack of the instrument panel and a green light will indicate the econ mode is engaged. When the fuel economy (econ) mode i...

  • Page 428

    Six-speed automatic transmission the shift lever position display (located in the instrument panel cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of the park position (refer to brake/transmission shift interlock system in this section). To ...

  • Page 429

    The transmission shift lever has only park, reverse, neutral, and drive shift positions. Manual shifts can be made using the electronic range select (ers) shift control (described later in this section). Moving the shift lever to the left or right (–/ +) while in the drive position will select the h...

  • Page 430

    Warning! (continued) • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move the shift lever rearward (with the brake pedal released) after you have placed it in park. Make sure the transmission is in park before leaving the vehicle. • it is dange...

  • Page 431

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 432

    Reverse this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral use this range when the vehicle is standing for prolonged periods with engine running. The engine may be started in this range. Set the parking brake and shift the tr...

  • Page 433

    When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading condi- tions, in hilly terrain, traveling into strong head winds, or while towing heavy trailers), use the electronic range select (ers) shift control (described below) to select a lower gear range. Un...

  • Page 434

    2. Shift the transmission into park. 3. Turn the engine off. 4. Wait approximately 10 seconds. 5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- m...

  • Page 435

    To exit ers mode, simply press and hold the shift lever to the right (+) until “d” is once again displayed in the shift lever position indicator in the instrument cluster. Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the ve...

  • Page 436

    Torque converter clutch a feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati- cally at calibrated speeds. This may result in a slightly different feeling or response during normal operation i...

  • Page 437

    Traction when driving on wet or slushy roads, it is possible for a layer of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precau- tions shoul...

  • Page 438

    Shallow standing water although your vehicle is capable of driving through shallow standing water, consider the following caution and warning before doing so. Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the...

  • Page 439

    Warning! • driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • driving through standing water limits your vehi- cle’s braking capabilities, which increases stop- ping distances. Therefore, after driving thr...

  • Page 440

    System. This noise should be considered normal, and it does not in any way damage the steering system. Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the ...

  • Page 441

    If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Parking brake before leaving the vehicle, make sure that the parking...

  • Page 442

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 443

    Warning! (continued) • be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury. Also be certain to leave the transmission in...

  • Page 444

    • a slight drop or fall away of the brake pedal at the end of the stop warning! • the anti-lock brake system contains sophisti- cated electronic equipment that may be suscep- tible to interference caused by improperly in- stalled, or high output radio transmitting equipment. This interference can ca...

  • Page 445

    Anti-lock brake warning light the “anti-lock brake warning light” moni- tors the anti-lock brake system. The light will come on when the ignition switch is turned to the on position and may stay on for as long as four seconds. If the “anti-lock brake warning light” remains on or comes on while drivi...

  • Page 446

    Wheel(s) and engine power is reduced, to provide en- hanced acceleration and stability. A feature of the tcs functions similarly to a limited-slip differential, and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply th...

  • Page 447

    Brakes. This can help reduce braking distances. The bas complements the abs. Applying the brakes very quickly results in the best bas assistance. To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence. Do not reduce brake pedal pressure unless b...

  • Page 448

    Esc uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match the intended path, esc applies the brake of the appro- priate wheel to assist in counteracting the oversteer or understeer condi...

  • Page 449

    Esc on this mode is the normal operating mode for esc on two-wheel drive vehicles. Whenever the vehicle is started, the esc system will be in this mode. This mode should be used for most driving situations. Esc should only be turned off for specific reasons as noted below. Esc partial off this mode ...

  • Page 450

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is turned to the on position. It should turn off with the engine running. If the “esc activation/malfunction indicat...

  • Page 451

    Hill start assist (hsa) the hsa system is designed to assist the driver when starting a vehicle from a stop on a hill. Hsa will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply th...

  • Page 452

    Electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)” in “un- derstanding your instrument panel” for further informa- tion. For vehicles not equipped with the evic, perform the following steps: note: you must complete steps 1 through 8 within 90 second...

  • Page 453

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision w...

  • Page 454

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 455

    Compact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Ex- ample: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing chart...

  • Page 456

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 457

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 458

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 459

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire and loading information placard tire placard location tire and loading information placa...

  • Page 460

    This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the ...

  • Page 461

    3. Subtract the combined weight of the driver and pas- sengers from xxx lbs or xxx kg. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the ...

  • Page 462

    460 starting and operating.

  • Page 463

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 464

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 465

    Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three-hour period. The cold tire inflation ...

  • Page 466

    Warning! High-speed driving, with your vehicle at or above maximum load, is dangerous. The added strain on your tires could cause them to fail. You could have a serious collision. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-ply tires war...

  • Page 467

    With one of the following types of non-matching tempo- rary use spares; compact, full size, or limited-use. Do not install more than one non-matching temporary use spare tire/wheel on the vehicle at any given time. Caution! Because of the reduced ground clearance, do not take your vehicle through an...

  • Page 468

    Warning! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnin...

  • Page 469

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressure listed on your tire and loading info...

  • Page 470

    Tread wear indicators tread wear indicators are in the original-equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 471

    Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline. Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold t...

  • Page 472

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 473

    Caution! To avoid damage to your vehicle or tires, observe the following precautions: • use chains on p225/65r16 and p235/60r16 tires only. P225/65r17 tires do not provide adequate clearance. • because of restricted chain clearance between tires and other suspension components, it is important that ...

  • Page 474

    Snow tires some areas of the country require the use of snow tires during the winter. All season tires can be identified by the m+s designation on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four;...

  • Page 475

    The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire pressure monitor system (tpms) the tpms will warn the driver of a low tire pressure based on the cold inflation tire pl...

  • Page 476

    The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effects, or natural air pressure loss through the tire. The tpms will continue to warn the driver of low tire pressure as long as the con...

  • Page 477

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or st...

  • Page 478

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system the tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure lev- els. Sensors, mounted to each wheel as part of the valve ste...

  • Page 479

    The “tire pressure monitoring telltale light” will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. The “tire pressure ...

  • Page 480

    5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare tire, the tpms will automatically update, and the “tire pressure monitoring telltale light” will turn off as long as no tire pressure is below the low-pressure warning limit in any of t...

  • Page 481

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tire pressure value. The system will automatically update, the graphic display of the p...

  • Page 482

    4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpms sensors. The evic will also display a “service tpm system” message for a minimum of five seconds when a system fault possibly related to an incorrect sensor location fault is present. In this case, the “service tpm sys...

  • Page 483

    4. For each subsequent ignition switch cycle, a chime will sound, the “tire pressure monitoring telltale light” will flash on and off for 75 seconds and then remain on solid, and the evic will display a “service tpm system” message for a minimum of five seconds and then display dashes (- -) in place...

  • Page 484

    Fuel requirements 3.6l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high-quality unleaded “regular” gaso- line having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide a...

  • Page 485

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Fuels blended with oxygenates may be used in your vehicle. Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in start...

  • Page 486

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • change the engine oil and oil filter • disconnect and reconnect the battery • drain the fuel tank (see your authorized dealer) more extensive repairs will be required for prolonged exposure to e-85 fuel. Mmt in gas...

  • Page 487

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 488

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 489

    The other sections of this manual for information on features that are common between flexible fuel and gasoline-only powered vehicles. Caution! Only vehicles with the e-85 fuel filler door label can operate on e-85. E-85 fuel cap e-85 badge 5 starting and operating 487.

  • Page 490

    Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap)...

  • Page 491

    • some additives used in regular gasoline are not fully compatible with e-85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as mopar 威 injector cleanup or techron may be used. Selection of engine oil...

  • Page 492

    Replacement parts many components in your flexible fuel vehicle (ffv) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol com- patible parts. Caution! Replacing fuel system components with non-ethanol compatible components can damage your veh...

  • Page 493

    Note: the driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door. Caution! • damage to the fuel system or emissions control system could result from using an improper fuel tank filler tu...

  • Page 494

    • if the gas cap is not tightened properly, the mil may come on. Be sure the gas cap is tightened every time the vehicle is refueled. Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will...

  • Page 495

    • vehicle identification number (vin) • type of vehicle • month, day and hour of manufacture (mdh) the bar code allows a computer scanner to read the vehicle identification number (vin). Gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, ...

  • Page 496

    Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a comm...

  • Page 497

    Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in t...

  • Page 498

    Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Note: the gcwr rating includes a 150 lbs (68 kg) allowance for the presence of a driver. Gross axle weight rating (gawr) the gawr is the maximum capacity of the fr...

  • Page 499

    Frontal area the frontal area is the maximum height multiplied by the maximum width of the front of a trailer. Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction assoc...

  • Page 500

    Warning! • an improperly adjusted weight-distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • weight-distributing hitch systems may not be compatible with surge brake couplers. Consult with an authorized hitch and trailer manufacturer or a...

  • Page 501

    With weight-distributing hitch (correct) improper adjustment of weight-distributing hitch (incorrect) 5 starting and operating 499.

  • Page 502

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow, and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classifications class max. Gtw...

  • Page 503

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Tongue wt. 3.6l/automatic 8,750 lbs (3 969 ...

  • Page 504

    Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side-to-s...

  • Page 505

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the “tire safety information/tire and loading informa...

  • Page 506

    Warning! (continued) • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision. •...

  • Page 507

    Towing requirements – tires • do not attempt to tow a trailer while using a compact spare tire. • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation proce...

  • Page 508

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 509

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following four-pin connector and seven-pin connector illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn...

  • Page 510

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic transmission the drive gear can be selected when towing. However, if frequent shifting occurs while in drive, use the electronic range select (ers) shift control...

  • Page 511

    • air conditioning turn off temporarily. Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle recreational towing is not allowed. Caution! Do not flat tow this vehicle. Damage to the drive- train will result. Note: this vehicle may be towed on a flatbed or vehicle ...

  • Page 513: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 513 䡵 if your engine overheats . . . . . . . . . . . . . . . . 513 䡵 jacking and tire changing . . . . . . . . . . . . . . . 514 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 515 ▫ spare tire...

  • Page 514

    䡵 freeing a stuck vehicle . . . . . . . . . . . . . . . . . 536 䡵 shift lever override . . . . . . . . . . . . . . . . . . . 537 䡵 towing a disabled vehicle . . . . . . . . . . . . . . . 539 ▫ without the ignition key . . . . . . . . . . . . . . 541 512 what to do in emergencies.

  • Page 515

    Hazard warning flashers the hazard warning flasher switch is located in the lower center area of the instrument panel. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Pr...

  • Page 516

    Caution! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “h”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h”, turn the engine off immedi...

  • Page 517

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack location the jack, jack handle and winch handle...

  • Page 518

    Spare tire removal the spare tire is stowed inside a protective cover located under the center of the vehicle between the front doors by means of a cable winch mechanism. The “spare tire drive” nut is located on the floor, under a plastic cap at the front of the floor console or under front super co...

  • Page 519

    1. Pull the lower drawer out from the rear of the floor console. 2. Open the front drawer to expose the storage compart- ment. Super console 1 — lower drawer 2 — front drawer 3 — front drawer liner lower drawer 6 what to do in emergencies 517.

  • Page 520

    3. Remove the liner from the console’s storage compart- ment to access the spare tire winch drive nut. Premium/base/cargo center console pull the winch cover assembly plug (if equipped) to access the winch drive nut. Spare tire tools the tool pouch contains three pieces and can be as- sembled into a...

  • Page 521

    Assembled t-handle a — spare tire hook/t-handle b — extension 1 c — extension 2 assembling the spare tire hook a — spare tire hook/t-handle b — extension 1 c — extension 2 6 what to do in emergencies 519.

  • Page 522

    Spare tire removal instructions the spare tire is located under the vehicle beneath the center console area. 1. Assemble the spare tire tools into a t-handle and place the square end over the spare tire winch drive nut. 2. Rotate the nut to the left until the winch mechanism stops turning freely. Th...

  • Page 523

    Note: if either front tire is flat it may be necessary to jack up the vehicle to remove the compact spare tire/ cover assembly from under the vehicle. 4. Stand the tire/cover assembly upright and remove the wheel spacer by squeezing the winch retaining tabs together. Push the retainer through the sp...

  • Page 524

    Preparations for jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Turn on t...

  • Page 525

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 526

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. Note: refer to the “compact spare tire” section of “tires – general information” for information about the spare tire, its use, and operation. 1. Loosen (but ...

  • Page 527

    Front jack location is on the sill flange of the vehicle body and is located 6 in (150 mm) from door edge. Note: in some situations the jack may need to be placed on its side in order to be pushed under the vehicle. Return the jack to its correct orientation once it is under the vehicle. Rear jackin...

  • Page 528

    Warning! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift...

  • Page 529

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Note: do not install the wheel cover on the compact spare. 7. Lower the vehicle by turning the jack sc...

  • Page 530

    Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. 10. Place the deflated (flat) tire and compact...

  • Page 531

    Warning! A loose compact spare tire/cover assembly, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the com- pact spare tire with the cover assembly in the place provided. Caution! The winch mechanism is designed for use with the winch t-handle onl...

  • Page 532

    Warning! Verify that both retainer tabs of the wheel spacer have been properly extended through the center of the wheel and spare tire/cover assembly. Failure to properly engage both retainer tabs could result in loss of the spare tire and cover assembly, which will cause vehicle damage and may caus...

  • Page 533

    3. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Ligh...

  • Page 534

    Correct tightness, have them checked with a torque wrench by your authorized dealer or service station. 7. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel. Vehicles without wheel covers 1. Mount the road tire on t...

  • Page 535

    Note: when using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electr...

  • Page 536

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 537

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper c...

  • Page 538

    8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle. If frequent jump-starting is required to start your vehicle you should have ...

  • Page 539

    Note: to improve the vehicle’s traction when starting off in deep snow, sand or gravel, it may be desirable to switch the electronic stability program (esp) to “partial off” mode. Refer to “electronic brake control system” in “starting and operating” for further information. Caution! • when “rocking...

  • Page 540

    2. Remove the shift lever override access cover located near the top right of the shift lever in the instrument panel. 3. Turn the ignition switch to the on/run position without starting the engine. 4. Press and maintain firm pressure on the brake pedal. 5. Using a small screwdriver or similar small...

  • Page 541

    Towing a disabled vehicle towing condition wheels off the ground all models flat tow none if transmission is operable: • transmission in neutral • 25 mph (40 km/h)max speed • 15 miles (24 km) max distance wheel lift rear front ok flatbed all best method proper towing or lifting equipment is required...

  • Page 542

    Caution! • do not use sling type equipment when towing. Damage to the fascia will occur. • when securing the vehicle to a flatbed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. • do not push or tow this vehicle with another vehicl...

  • Page 543

    Caution! Towing faster than 25 mph (40 km/h) or farther than 15 miles (24 km) with front wheels on the ground can cause severe damage to the transmission. Such dam- age is not covered by the new vehicle limited warranty. Without the ignition key special care must be taken when the vehicle is towed w...

  • Page 545: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . . . . . 545 䡵 onboard diagnostic system — obd ii . . . . . . 546 ▫ loose fuel filler cap message . . . . . . . . . . . 546 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 546

    ▫ automatic transmission . . . . . . . . . . . . . . . 569 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 571 ▫ cleaning the instrument panel cupholders . . 577 䡵 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578 ▫ totally inte...

  • Page 547

    Engine compartment — 3.6l 1 — air filter 6 — engine coolant reservoir 2 — power steering fluid reservoir 7 — engine oil dipstick 3 — brake fluid reservoir 8 — engine oil fill 4 — battery 9 — coolant pressure cap 5 — totally integrated power module (fuses) 10 — washer fluid reservoir 7 maintaining yo...

  • Page 548

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 549

    “electronic vehicle information center (evic)” in ”un- derstanding your instrument panel” for further informa- tion. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tight- ened. Press the odometer reset button to turn the message off. If the ...

  • Page 550

    2. If you crank or start the engine, you will have to start this test over. 3. As soon as you turn the ignition switch to the on position, you will see the mil symbol come on as part of a normal bulb check. 4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for a...

  • Page 551

    Replacement parts use of genuine mopar 威 parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-mopar 威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty. Dealer ser...

  • Page 552

    Caution! • failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle perfor- mance. Immediately have potential malfunctions examined by an authorized chrysler group llc dealer...

  • Page 553

    Caution! Overfilling or underfilling will cause oil aeration, or loss of oil pressure. This could damage your engine. Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for further i...

  • Page 554

    Engine oil viscosity (sae grade) sae 5w-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil ...

  • Page 555

    Engine oil filter selection the manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar 威 engine oil filters are a high...

  • Page 556

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 557

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions con- trol device and may seriously reduce engine per- formance and cause serious damage to the engine. • damage to the catalytic converter can r...

  • Page 558

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 559

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and are identified on the battery case. Cable clamps should b...

  • Page 560

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 561

    Warning! Do not remove the a/c air filter while the blower is operating or personal injury may result. The a/c air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1. Open the glove compartment and remove all contents. 2. Push in...

  • Page 562

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7. Rotate the glove compartment door back into position. Body lubrication locks and all body pivot points...

  • Page 563

    Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may ...

  • Page 564

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at anytime the ignition switch is in the on position. • you or others can be badly burned by hot engi...

  • Page 565

    Cooling system – drain, flush, and refill if the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant...

  • Page 566

    Adding coolant your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 104,000 miles (169 000 km) before replacement. To prevent reducing this extended mainte- nance period, ...

  • Page 567

    Cooling system pressure cap the cap must be fully tightened to prevent the loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign...

  • Page 568

    Engine cold, the level of the engine coolant (antifreeze) in the coolant recovery bottle should be between the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or...

  • Page 569

    • maintain engine coolant (antifreeze) concentration at 50% hoat engine coolant (antifreeze) (minimum) and distilled water for proper corrosion protection of your engine, which contains aluminum components. • make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or ob...

  • Page 570

    Master cylinder – brake fluid level check the fluid level in the master cylinder should be checked when performing underhood services, or immediately if the “brake system warning light” indicates system failure. Clean the top of the master cylinder area before removing the cap. Add fluid to bring th...

  • Page 571

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 572

    Selection of lubricant it is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only the manufacturer’s recommended trans- mission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further informa-...

  • Page 573

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the six-speed automatic transmission is a sealed unit and has no dipstick. See your authorized deale...

  • Page 574

    The most common causes are: • road salt, dirt and moisture accumulation • stone and gravel impact • insects, tree sap and tar • salt in the air near seacoast localities • atmospheric fallout/industrial pollutants washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mo...

  • Page 575

    Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain holes in the lower edges of the doors and rocker panels be kept clear and open. • if you detect any stone chips or scratches in the ...

  • Page 576

    Caution! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s pro- tective finish. Use only the app...

  • Page 577

    Cleaning interior trim interior trim should be cleaned starting with a damp cloth, a damp cloth with mopar 威 total clean or equiva- lent, then mopar 威 spot & stain remover or equivalent if absolutely necessary. Do not use harsh cleaners or armor all 威. Use mopar威 total clean or equivalent to clean v...

  • Page 578

    To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Gl...

  • Page 579

    Replace the seat belts if they appear frayed or worn, or if the buckles do not work properly. Cleaning the instrument panel cupholders removal pull the flexible liner from the cupholder drawer starting at one edge to ease removal. Cleaning the liner is top shelf dishwasher safe, or you may follow th...

  • Page 580

    Fuses totally integrated power module the totally integrated power module is located in the engine compartment near the battery. Refer to the appli- cable “engine compartment” illustration in this section. This center contains cartridge fuses and mini-fuses. A label that identifies each component ma...

  • Page 581

    Caution! • when installing the totally integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power module, and possibly result in a electrical system failure. • when replacing a blown f...

  • Page 582

    Cavity cartridge fuse mini- fuse description j8 40 amp green — power memory seat – if equipped j9 40 amp green — partial zero emis- sions vehicle motor/ flex fuel – if equipped j10 30 amp pink — headlamp wash/ manifold tuning valve – if equipped j11 30 amp pink — power sliding door module/anti–theft...

  • Page 583

    Cavity cartridge fuse mini- fuse description m1 — 15 amp blue rear center brake lamp/brake switch m2 — 20 amp yellow trailer lighting, front fog lamps, intelli- gent battery sensor (ibs) m3 — 20 amp yellow front/rear axle locker, vacuum pump motor m4 — 10 amp red trailer tow m5 — 25 amp natural inve...

  • Page 584

    Cavity cartridge fuse mini- fuse description m10 — 15 amp blue ignition off draw — video system, satel- lite radio, dvd, hands-free module, universal garage door opener, vanity lamp, streaming video module – if equipped m11 — 10 amp red climate control sys- tem m12 — 30 amp green amplifier/radio m13...

  • Page 585

    Cavity cartridge fuse mini- fuse description m19 — 25 amp natural powertrain m20 — 15 amp blue instrument cluster interior light, switch bank, steering col- umn module, switch steering wheel m21 — 20 amp yellow powertrain m22 — 10 amp red horn m23 — 10 amp red horn m24 — 25 amp natural rear wiper ca...

  • Page 586

    Cavity cartridge fuse mini- fuse description m32 — 10 amp red airbag module, thatchum – if equipped m33 — 10 amp red powertrain m34 — 10 amp red park assist, heater climate control mod- ule, headlamp wash, compass, rear cam- era, door lamps, flashlight, relay die- sel cabin heater, rad fan diesel – ...

  • Page 587

    Steering column. If you experience temporary or perma- nent loss of these systems, see your authorized dealer for service. Vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take steps to protect your battery. You may do the following: • remove the 20 amp ...

  • Page 588

    Light bulbs – exterior bulb number headlamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H11 fog lamp – if equipped . . . . . . . . . . . . . . . . Psx24w front side marker, park/ turn signal . . . . . . . . . . . . . . . . . . 3757a or py27/7w rear tail, stop, turn signal lamp . . . . ...

  • Page 589

    Front park/turn signal lamps 1. Raise the hood to access the rear of the headlamp housing. 2. Twist the turn signal socket and remove from the headlamp housing, then pull the bulb out. 3. Push the new bulb into the socket and reinstall the socket by twisting until locked into the headlamp housing. F...

  • Page 590

    Rear tail, stop, turn signal, side marker and backup lamps 1. Raise the liftgate. 2. Remove the tail lamp assembly by removing the two screws from the inboard side. Use a fiber stick or similar tool to gently pry the light on the outboard side to disengage the two ball studs. Note: • if a screwdrive...

  • Page 591

    License lamp the license plate lamp is located under the tailgate light bar and above the license plate. 1. Using a small screwdriver, press inward the locking tab on the outboard side of the lamp assembly and pull down on the lamp assembly for removal. 2. Twist and remove the socket from the lamp a...

  • Page 592

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant five year/100,000 mile formula hoat (hybrid organic additive technology) or equivalent. Engine oil use api certified sae 5w-30 engine oil, meeting the requirements of chr...

  • Page 593

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Brake master cylinder mopar 威 dot 3 and sae j1703 should be used or equivalent. If dot 3 brake fluid is not available, then dot 4 is acceptab...

  • Page 595: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 594 ▫ required maintenance intervals . . . . . . . . . . 596 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 596

    Maintenance schedule the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating condition...

  • Page 597

    Note: • the oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is not illuminated. • change your engine oil more often if you drive your vehicle off...

  • Page 598

    Once a month • check tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of the coolant reservoir, brake master cylinder, and the power steering and add as needed. • check all lights and other electrical i...

  • Page 599

    8,000 miles (13,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). Odometer reading date repair order # dealer code signature, authorized ser...

  • Page 600

    24,000 miles (39,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. Odometer reading dat...

  • Page 601

    40,000 miles (65,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). Odometer reading date repair order # dealer code signature, authorized ...

  • Page 602

    56,000 miles (91,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). Odometer reading date repair order # dealer code signature, authorized ...

  • Page 603

    72,000 miles (117,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. Odometer reading d...

  • Page 604

    88,000 miles (143,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). Odometer reading date repair order # dealer code signature, authorize...

  • Page 605

    104,000 miles (169,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ flush and replace the engine coolant at 104,000 miles (169 000 km...

  • Page 606

    120,000 miles (195,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. ❏ change the aut...

  • Page 607

    136,000 miles (221,000 km) or 102 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 136,000 miles (221 000 km). Odometer reading date repair order # dealer code signature, author...

  • Page 608

    152,000 miles (247,000 km) or 114 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 152,000 miles (247 000 km). Odometer reading date repair order # dealer code signature, author...

  • Page 609

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • failure to properly inspect and mai...

  • Page 611: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611 ▫ prepare for the appointment . . . . . . . . . . . 611 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 611 ▫ be reasonable with r...

  • Page 612

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 617 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 617 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 617 ▫ temperature grades . . . . . . . . . . . . . . . . . . 61...

  • Page 613

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 614

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 615

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 616

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 617

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 618

    • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, and/or...

  • Page 619

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 620

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 621: Index

    Index 10

  • Page 622

    Adding engine coolant (antifreeze) . . . . . . . . . . 564 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 490 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 561 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . 484 adjustable pedals . . . . . . . . ....

  • Page 623

    Automatic headlights . . . . . . . . . . . . . . . . . . . . 199 automatic temperature control (atc) . . . . . . . . . 400 automatic transaxle selection of lubricant . . . . . . . . . . . . . . . . . 591 automatic transmission . . . . . . . . . . . . . . . . 422,569 adding fluid . . . . . . . . . . ...

  • Page 624

    Caps, filler fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490 oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . 552 power steering . . . . . . . . . . . . . . . . . . . . . . 438 radiator (coolant pressure) . . . . . . . . . . . . . 565 car washes . . . . . . . . . . ....

  • Page 625

    Connector uci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 universal consumer interface (uci) . . . . . . . 346 conserving fuel . . . . . . . . . . . . . . . . . . . . . . . . 310 console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 console, floor . . . . . . . ...

  • Page 626

    Disposal antifreeze (engine coolant) . . . . . . . . . . . . . 565 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . 552 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 door locks, automatic . . . . . . . . . . . . . . . . . . . . 35 door opener, garage . . . . . ....

  • Page 627

    Flooded, starting . . . . . . . . . . . . . . . . . . . . . 420 fuel requirements . . . . . . . . . . . . . . . . . 482,589 oil . . . . . . . . . . . . . . . . . . . . . . . . . 550,589,590 oil change interval . . . . . . . . . . . . . . . . . . . 551 oil disposal . . . . . . . . . . . . . . . . . ....

  • Page 628

    Replacement parts . . . . . . . . . . . . . . . . . . . . 490 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 489 flooded engine starting . . . . . . . . . . . . . . . . . . . 420 floor console . . . . . . . . . . . . . . . . . . . . . . . . . . 261 fluid capacities . . . . . . . . . ...

  • Page 629

    Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578 garage door opener (homelink®) . . . . . . . . . . . 231 gas cap (fuel filler cap) . . . . . . . . . . . . 490,492,546 gasoline (fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 482 conserving . . . . . . . . . . . . . ...

  • Page 630

    Hill start assist . . . . . . . . . . . . . . . . . . . . . . . . . 449 hitches trailer towing . . . . . . . . . . . . . . . . . . . . . . . 500 homelink® (garage door opener) transmitter . . 231 hood release . . . . . . . . . . . . . . . . . . . . . . . . . . 196 hook, coat . . . . . . . . . . . . ...

  • Page 631

    Latch (lower anchors and tether for children) . . . . . . . 90 latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 lead free gasoline . . . . . . . . . . . . . . . . . . . . . . 482 leaks, fluid . . . . . . . . ...

  • Page 632

    Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587 passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 reading . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 rear servicing . . . . . . . . . . . . . . . . . . . . . . . 588 rear tail . . . . . . . . . . . ...

  • Page 633

    Memory seat . . . . . . . . . . . . . . . . . . . . . . . . 115,192 methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483 mini-trip computer . . . . . . . . . . . . . . . . . . . . . . 311 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 automatic dimming . ...

  • Page 634

    Viscosity . . . . . . . . . . . . . . . . . . . . . . . . 552,589 onboard diagnostic system . . . . . . . . . . . . . . 546,547 opener, garage door (homelink®) . . . . . . . . . . . 231 operator manual (owner’s manual) . . . . . . . . . . . . 4 outside rearview mirrors . . . . . . . . . . . . . . . ...

  • Page 635

    Radio operation . . . . . . . . . . . . . . . . . . . . . . . . 392 radio remote controls . . . . . . . . . . . . . . . . . . . . 390 rear air conditioning . . . . . . . . . . . . . . . . . 398,408 rear camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 rear cross path . . . . . . . . ...

  • Page 636

    Seat belt reminder . . . . . . . . . . . . . . . . . . . . . . . 68 seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 52,101 adjustable shoulder belt . . . . . . . . . . . . . . . . 61 adjustable upper shoulder anchorage . . . . . . 61 and pregnant women . . . . . . . . . . . . . . . ...

  • Page 637

    Snow chains (tire chains) . . . . . . . . . . . . . . . . . 470 snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472 spare tire . . . . . . . . . . . . . . . . . . . . . . . 465,466,516 speed control (cruise control) . . . . . . . . . . . . . . 212 speedometer . . . . . . . . . . ....

  • Page 638

    Text messaging . . . . . . . . . . . . . . . . . . . . . . . . . 147 tilt steering column . . . . . . . . . . . . . . . . . . . . . 208 tire and loading information placard . . . . . . . . . 457 tire identification number (tin) . . . . . . . . . . . . . 455 tire markings . . . . . . . . . . . . . . ...

  • Page 639

    Traction control . . . . . . . . . . . . . . . . . . . . . . . . . 443 traction control switch . . . . . . . . . . . . . . . . . . . 443 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . 495 cooling system tips . . . . . . . . . . . . . . . . . . 508 hitches . . . . . . . . . . . . ...

  • Page 640

    Vehicle modifications/alterations . . . . . . . . . . . . . . 7 vehicle storage . . . . . . . . . . . . . . . . . . . . . . . 412,585 voice recognition system (vr) . . . . . . . . . . . . . . 155 warning flasher, hazard . . . . . . . . . . . . . . . . . . 513 warning lights (instrument cluster descr...

  • Page 641

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 642

    R a m c v c a r g o v a n chrysler group llc o w n e r ’ s m a n u a l 2 0 1 2 2 0 12 ram c argo v an 12mzz-126-aa first edition printed in u.S.A. 1199168 ram truck 1500-2500-3500 om cover.Indd 1 3/29/12 2:55 pm.