Operation manual notice d’emploi bedienungsanleitung p-7536-845 qxpdqxdoc 6/08 © 2008 by c.E. Studio-2 s.L. - spain (eec) http://www.Ramaudio.Com e-mail: support@ramaudio.Com professional power amplifiers 604-1204-1208-2408 t series.
Warning: the exclamation point inside an equilateral triangle indicates the existen- ce of internal components whose substi- tution may affect safety. The lightning and arrowhead symbol warns about the presence of uninsula- ted dangerous voltage. To avoid fire or electrocution risk do not expose the...
0 safety precautions 1 general information 1.1 introduction 1.2 main characteristics 2 controls: where and what? 2.1 front panel 2.2 rear panel 3 installation and operation 3.1 connections 3.1.1 dual channel mode 3.1.2 bridge channel mode 3.2 configuration 3.3 troubleshooting 4 technical specificati...
The t series of amplifiers has been specifically developed for fixed installa- tion and/or network applications. Thus they are equipped with specific connec- tors: euro style input and screw terminal barrier strip output, to offer clear, direct and hassle-free connectivity. Furthermore they offer up...
Lokalisierung der funktionen see figure signal attenuation level control knobs: permit independent control of each channel’s attenuation (21 steps). Signal: this led indicates pre- sence of signal at the inputs. Prot : this led shows temperatu- re protection is active. Icl: led indicating intelligen...
See figure signal input: euro style connectors for the amplifier’s signal input. Configuration switch: sub sonic filter, gain and bridge (see page 9). Speaker connectors: screw termi- nal barrier strip to connect the spea- kers. 5 2.2 rear panel 4 1 2 siehe fig. Eingangssignal: euro style für den si...
The power switch must always be on the “off” position before plugging the amp to a properly earthed mains soc- ket (220-240v ac / 110v-120v ac). The input signal fed to the amplifier can be either balanced or un-balanced. The drawing below describes both ways to wire an euro style connector for the ...
Installation and operation installation et mise en service the amplifier can operate on two diffe- rent configurations: dual or bridge. The connections for the two modes are different. See figure - switch “off” the amp. - set the configuration minidips on the rear panel to no bridge (see page 9). - ...
3 dual mode 8 4 bridge mode.
The amplifier has an ensemble of mini- dips on the back panel, which allow for the following configurations: the high- pass subsonic filter, the gain selection and the bridge mode. All these configu- rations can be cross-set in any way, independently from the others. The basic configuration possibil...
In the event of incorrect connection or misfunctioning, the amp will activate one or more of its led to warn about the problem. Correct function: sgnl lights to indi- cate signal presence. Icl: the intelligent clip limiter is ope- rating. No signal: no input signal is reaching the amp. Protections: ...
4.2 data 4.2 données techniques 4.2 technische daten technical specifications spécifications technische spezifikationen 11 technical specifications t-604 t-1204 t-1208 t-2408 output power continuous average power rms, 1khz, 1.0% thd+n @ 4 Ω 4x 160 w 4x 320 w 8x 150 w 8x 300 w @ 8 Ω 4x 115 w 4x220 w ...
Manufactured in the eec by c.E. Studio-2 s.L. Pol. Ind. La lloma - c/sierra perenxisa nº28 46960 aldaya - valencia - spain phone: +34 96 127 30 54 fax: +34 96 127 30 56 http://www.Ramaudio.Com e-mail: support@ramaudio.Com.