1. DL manuals
  2. RAM
  3. Trucks
  4. Truck 2500 2011
  5. Owner's Manual

RAM Truck 2500 2011 Owner's Manual

Other manuals for Truck 2500 2011: Owner's Manual

Summary of Truck 2500 2011

  • Page 1

    1 5 0 0 / 2 5 0 0 / 3 5 0 0 chrysler group llc o w n e r ’ s m a n u a l 2 0 1 1 2 0 1 1 r a m t r u c k 11d241-126-ab second edition printed in u.S.A. Ram truck.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 4 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 6 䡵 van conversions/campers . . . . . . . . . . . . . . . . . 6 䡵 vehicle identifi...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 9

    Vehicle identification number the vehicle identification number (vin) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the auto- mobile information disclosure label affixed to a window on your vehicle, the vehicle registration and...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ wireless ignition node (win) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 12 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ removing key fob f...

  • Page 12

    ▫ remote open window feature — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . 24 ▫ programming additional transmitters . . . . . . 24 ▫ transmitter battery replacement . . . . . . . . . . 24 ▫ general information . . . . . ....

  • Page 13

    ▫ enhanced seat belt use reminder system (beltalert 威) . . . . . . . . . . . . . . . . . . . . . . . . . 51 ▫ seat belts and pregnant women . . . . . . . . . . 52 ▫ seat belt extender . . . . . . . . . . . . . . . . . . . . . 52 ▫ supplemental restraint system (srs) – airbags . . . . . . . . . . . ....

  • Page 14

    A word about your keys key fob with remote keyless entry (rke) — if equipped your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a wireless ignition node (win) with integral ignition switch. You can insert the key fob into th...

  • Page 15

    Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key ...

  • Page 16

    To remove the emergency key, slide the mechanical latch at the top of the key fob sideways with your thumb and then pull the key out with your other hand. Note: you can insert the double-sided emergency key into the lock cylinder with either side up. Removing key fob from ignition place the shift le...

  • Page 17

    (evic)/personal settings (customer-programmable features)” in “understanding your instrument panel” for further information. Warning! • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fata...

  • Page 18

    Sentry key 姞 the sentry key 威 immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses a key fob with a factory-mated remot...

  • Page 19

    All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics. Replacement keys note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to ...

  • Page 20

    General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference...

  • Page 21

    Note: if the vehicle security light stays on continu- ously during vehicle operation, have the system checked by an authorized dealer. To disarm the system use the rke transmitter to unlock the door. If something has triggered the system in your absence, the horn will sound three times when you unlo...

  • Page 22

    Note: • the front courtesy overhead console and door cour- tesy lights do not turn off if the dimmer control is in the “dome on” position (extreme top position). • the illuminated entry system will not operate if the dimmer control is in the “dome defeat” position (extreme bottom position). Remote k...

  • Page 23

    Setup for driver door first, otherwise this will unlock all doors), or twice within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote key unlock, driver door/all doors first this feature lets y...

  • Page 24

    Flash lamps with remote key lock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to “...

  • Page 25

    Sound horn with remote key lock this feature will cause the horn to chirp when the doors are locked with the rke transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to “elec- tronic vehicle informat...

  • Page 26

    Using the panic alarm to turn the panic alarm feature on or off, press and hold the panic button on the rke transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on. Th...

  • Page 27

    1. With the rke transmitter buttons facing down, use a flat blade screwdriver to pry the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. 2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterior...

  • Page 28

    Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m). Note: the vehicle must be equipped with an auto- matic...

  • Page 29

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted - door ajar • remote start aborted - hood ajar • remote start abor...

  • Page 30

    Note: to avoid unintentional shut downs, the system will disable the one time press of the remote start button for two seconds after receiving a valid remote start request. To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, press and release the unlock button on t...

  • Page 31

    Door locks manual door locks front and rear doors may be locked by moving the lock knob down or unlocked by moving the lock knob up. Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed. The emergency key will...

  • Page 32

    Power door locks — if equipped a power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. If you press the power door lock switch while the key fob is in the ignition, and any front door is open, the power locks will not operate. This prevents you from ac...

  • Page 33

    6. The doors were not previously locked using the power door lock switch or remote keyless entry (rke) transmitter automatic door locks programming — if equipped the automatic door locks feature can be enabled or disabled as follows: • for vehicles equipped with the electronic vehicle information ce...

  • Page 34

    Auto unlock doors — if equipped this feature unlocks all of the doors of the vehicle when either front door is opened. This will occur only after the vehicle has been shifted into the park position after the vehicle has been driven (shifted out of park and all doors closed). Auto unlock doors progra...

  • Page 35

    Child-protection door lock to provide a safer environment for children riding in the rear seat, the rear doors (if equipped) of your vehicle have the child-protection door lock system. To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to enga...

  • Page 36

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: • after setting the child-protection door lock system, always test the door from the inside to make certain it is in the des...

  • Page 37

    Windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of quad cab 威, mega cab威 and crew cab models. The windows will operate when the ignition switch is turned to the on/run or acc posi- tion, and for up to 10 minutes aft...

  • Page 38

    To open the window part way, press to the first detent and release it when you want the window to stop. Auto-up feature with anti-pinch protection (4-door models driver and front passenger door only) — if equipped lift the window switch fully upward to the second detent, release, and the window will...

  • Page 39

    2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Window lockout switch — 4–door models the window lockout switch on the driver’s door allows you to disable the w...

  • Page 40

    Normal occurrence and can be minimized. If the rear windows are open and buffeting occurs, open the front and rear windows together to minimize the buffeting. Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belt...

  • Page 41

    Note: the advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. Please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep ...

  • Page 42

    Accident the belt will lock and reduce the risk of you striking the inside of the vehicle or being thrown out. Warning! • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the force...

  • Page 43

    Plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” pulling out latch plate and webbing latch plate to buckle 2 things t...

  • Page 44

    Warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you properly. In a sudden stop you cou...

  • Page 45

    Tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in an accident. Warning! • a lap belt worn too high can increase the risk of internal injury in an accident. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Alw...

  • Page 46

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in an accident and leave you with no protecti...

  • Page 47

    2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible “click”. For proper seatbelt usage, refer “lap/shoulder belt operating instructions”. Warning! • if the black l...

  • Page 48

    Inserting latch plate in use position 46 things to know before starting your vehicle.

  • Page 49

    Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold ...

  • Page 50

    You will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Center lap belts the center seating position for the quad cab 威, mega cab 威 and crew cab front seat has a lap belt only. To fasten the lap belt, slide the latch pl...

  • Page 51

    Warning! • the belt and retractor assembly must be replaced if the seat belt assembly “automatic locking re- tractor (alr)” feature or any other seat belt func- tion is not working properly when checked ac- cording to the procedures in the service manual. • failure to replace the belt and retractor ...

  • Page 52

    Automatic locking retractor (alr) mode – if equipped in this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. When to use the automatic locking mode use the automatic locking mode anytime a child safety seat is installed in a...

  • Page 53

    Accident. These devices may improve the performance of the seat belt by assuring that the belt is tight around the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints. Note: these devices are not a substitute for proper seat belt placement by...

  • Page 54

    1. With all doors closed and the ignition switch in any position except on/run or start, buckle the driver’s seat belt. 2. Turn the ignition switch to the on/run position and wait for the seat belt reminder light to turn off. 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle ...

  • Page 55

    Extender should be used only if the existing belt is not long enough. When it is not required, remove the ex- tender and store it. Warning! Using a seat belt extender when not needed can increase the risk of injury in an accident. Only use the seat belt extender when the lap belt is not long enough ...

  • Page 56

    The advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the...

  • Page 57

    • supplemental side airbag inflatable curtains (sabic) • front and side impact sensors • front seat belt pretensioners, seat belt buckle switch, and seat track position sensors advanced front airbag features the advanced front airbag system has multistage driver and front passenger airbags. This sys...

  • Page 58

    Supplemental side airbag inflatable curtain (sabic) — if equipped sabic airbags may offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant ...

  • Page 59

    Warning! • if your vehicle is equipped with left and right supplemental side airbag inflatable curtain (sabic), do not stack luggage or other cargo up high enough to block the location of the sabic. The area where the sabic is located should re- main free from any obstructions. • do not use accessor...

  • Page 60

    Here are some simple steps you can take to minimize the risk of harm from a deploying airbag: children 12 years old and under should always ride buckled up in a rear seat. Warning! Infants in rear-facing child restraints should never ride in the front seat of a vehicle with a passenger advanced fron...

  • Page 61

    Do not lean against the door or window. If your vehicle has side airbags, and deployment occurs, the side airbags will inflate forcefully into the space between you and the door. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer center. ...

  • Page 62

    Based on the impact sensor’s signals, a central electronic orc deploys the advanced front airbags, sabic air- bags — if equipped, and front seat belt pretensioners — if equipped, as required, depending on the severity and type of impact. Advanced front airbags are designed to provide addi- tional pr...

  • Page 63

    Position, in the acc position, or not in the ignition, the airbag system is not on and the airbags will not inflate. The orc contains a backup power supply system that may deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment. Also, the orc turns on the ai...

  • Page 64

    Based on the collision type and severity. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in about 50 to 70 milliseconds. This is about half of the time it takes t...

  • Page 65

    Enhanced accident response system in the event of an impact causing airbag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the orc will determine whether to have the enhanced accident response system perform the follow- ing ...

  • Page 66

    Airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, fol...

  • Page 67

    Warning! (continued) • do not attempt to modify any part of your airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any airbag system service. If your seat, including your trim cover and cushion, ne...

  • Page 68

    Located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good. Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, su...

  • Page 69

    Such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. Child restraints everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the united states and all canadian province...

  • Page 70

    Infants and small children • safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and ⬙convertible⬙ child seats. Both types of child...

  • Page 71

    • the belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a be...

  • Page 72

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably and whose legs are long enough to bend over the front of the seat when their back is against the seatback should use the lap/shoulder belt in a rear seat. • make sure that the child is upright in...

  • Page 73

    From the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. • if the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle,...

  • Page 74

    Lower anchors and tether for children (latch) each vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tether for children. The latch system provides for the installation of the child restraint without using the vehicle seat belt, instead ...

  • Page 75

    Some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- ages wi...

  • Page 76

    Installing the child restraint system warning! Do not install child restraint systems equipped with latch mechanisms in the center position of a quad cab 威 rear seat, or crew cab model with a bench rear seat. A child may be placed in the rear center seating position of a quad cab 威, or crew cab benc...

  • Page 77

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 78

    Child restraint tether anchor child restraints having tether straps and hooks for con- nection to tether anchors have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for their older products. Regular cab models have two tether anchorage...

  • Page 79

    Tether anchorage points at the right and center front seat (regular cab - all seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat. 2. Lift the cover (if so equipped...

  • Page 80

    Multiple child restraint installation sequence (quad cab 威/crew cab/mega cab威 - rear seats) mega cab 威 1. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and then to the anchor...

  • Page 81

    Quad cab 威/crew cab 1. The tether straps loops are located between the rear glass and the rear seat. There is a tether strap loop located behind each seating position. You can gain access to the center seating position tether strap loop by raising the head restraint and reaching between the rear gla...

  • Page 82

    3. Pass each tether strap hook under the head restraint and through the loop of webbing behind the child seat. 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the anchor loop. 5. Place a child restraint on the center rear seat and adjust the tether strap so t...

  • Page 83

    Transporting pets airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in an accident. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat...

  • Page 84

    Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 85

    If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control...

  • Page 86

    Authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an autho- rized dealer. Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. Se...

  • Page 87

    Warning! (continued) • check mounting of mats on a regular basis. Al- ways properly reinstall and secure floor mats that have been removed for cleaning. • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake peda...

  • Page 88

    Fluid leaks check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately. 86 things to know before...

  • Page 89: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 93 ▫ automatic dimming mirror — if equipped . . . 94 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 95...

  • Page 90

    ▫ power lumbar — if equipped . . . . . . . . . . . 104 ▫ heated seats — if equipped . . . . . . . . . . . . 104 ▫ ventilated seats — if equipped . . . . . . . . . . 107 ▫ manual seat adjuster — if equipped . . . . . . 108 ▫ manual reclining seats — if equipped . . . . . 109 ▫ 40-20-40 front bench se...

  • Page 91

    ▫ daytime running lights (drl) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 127 ▫ multifunction lever . . . . . . . . . . . . . . . . . . 127 䡵 windshield wipers and washers . . . . . . . . . . 129 ▫ windshield wipers . . . . . . . . . . . . . . . . . . . 129 ▫ windshield washer...

  • Page 92

    䡵 parkview威 rear back up camera — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 ▫ turning parkview威 on or off — with navigation/multimedia radio . . . . . . . . . . . 149 ▫ turning parkview威 on or off — without navigation/multimedia radio . . . . . . . . . . . 149 䡵 overhea...

  • Page 93

    ▫ sunroof maintenance . . . . . . . . . . . . . . . . . 161 ▫ ignition off operation . . . . . . . . . . . . . . . . . 161 䡵 electrical power outlets . . . . . . . . . . . . . . . . . 162 䡵 cigar lighter and ash receiver — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 166 䡵 power i...

  • Page 94

    ▫ power sliding rear window — if equipped . . . . . . . . . . . . . . . . . . . . . . . . 181 ▫ manual sliding rear window — if equipped . . . . . . . . . . . . . . . . . . . . . . . . 181 䡵 fold flat load floor — if equipped . . . . . . . . 181 䡵 rambox威 — if equipped . . . . . . . . . . . . . . . ...

  • Page 95

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. The mirror should be adjusted while set in the day position (toward the windshield). Headlight glare can be reduced b...

  • Page 96

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 97

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they ...

  • Page 98

    Caution! It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location. Power mirrors — if equipped the controls for the power mirrors are located on the driver’s door trim panel. The power mirror controls consist of mirror selec...

  • Page 99

    To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Power folding outside mirrors — if equipped if equipped with power folding mirrors, they can...

  • Page 100

    35 mph (56 km/h), the fold feature will be disabled, however the mirrors will attempt to unfold at any speed. If you attempt to unfold the mirrors at high speeds, they may not fully unfold - slow down and try again. The switch for the power folding mirrors is located between the power mirror switche...

  • Page 101

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “rear window features” in “understanding the features of your vehicle” for further information. Driver’s automatic dimming mirror — if equipp...

  • Page 102

    To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until the sun visor is in the desired position. Trailer towing mirrors — if equipped these mirrors are designed with an adjustable mirror head to provide a greater vision range...

  • Page 103

    Note: fold the trailer towing mirrors rearward prior to entering an automated car wash. A small blindspot mirror is located next to main mirror and can be adjusted separately. Uconnect™ phone — if equipped uconnect™ phone is a hands-free system that allows you to use voice commands to dial a phone n...

  • Page 104

    Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure ever...

  • Page 105

    Move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting the seat up or down the height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch...

  • Page 106

    Caution! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power lumbar — if equipped vehicles equipped with power driver or passenger seat...

  • Page 107

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 108

    Press the switch once to select high- level heating. Press the switch a sec- ond time to select low-level heating. Press the switch a third time to shut the heating elements off. Note: • once a heat setting is selected, heat will be felt within two to five minutes. • the engine must be running for t...

  • Page 109

    Indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high- level heating. Press the switch a sec- ond time to select low-level heating. Press the switch a third time to shut the...

  • Page 110

    Press the switch once to choose high, press it a second time to choose low. Pressing the switch a third time will turn the ventilated seat off. When high speed is selected both lights on the switch will be illuminated. When low speed is selected one light will be illuminated. Note: the engine must b...

  • Page 111

    Have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision a...

  • Page 112

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Dump feature — manual recline seat only actuating the recliner handle will allow the s...

  • Page 113

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Folding rear seat (table mode) — if equipped both the left and right rear seatbacks ca...

  • Page 114

    2. Fold the seatback forward. 3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place. Folding rear seat — if equipped both the outboard rear seats will drop and move forward when the seatback is folded flat. Warning! • it is dangerous to ride in a c...

  • Page 115

    To fold either rear seat flat: 1. Lift the handle, located on the outboard side of either of the rear seats. 2. Fold the seatback down and push the seat forward. 3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place. Handle rear passenger fold flat sea...

  • Page 116

    Warning! An improperly latched seat could cause serious in- jury or death. Make sure that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. Head restraints head restrai...

  • Page 117

    Rear head restraints the two outboard seat are equipped with adjustable head restraints. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the adjustment button, located on the base of the head restraint, and push downward on the head restraint. Note:...

  • Page 118

    • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. Driver memory seat — if equipped driver memory seats allow the driver to recall settings for the adjustable pedals, mirr...

  • Page 119

    Keyless entry (rke) transmitters can also be pro- grammed to recall the same positions when the un- lock button is pressed. Note: the power lumbar option is not programmable with driver memory seats. Your vehicle was delivered with two rke transmitters. One or both rke transmitters can be linked to ...

  • Page 120

    8. Turn the ignition off and remove the key. 9. Press and release the lock button on one of the rke transmitters. 10. Repeat the above steps to set the next memory position using the other numbered memory button or to link another rke transmitter to memory. Memory position recall note: • the vehicle...

  • Page 121

    To disable a rke transmitter linked to memory 1. Turn the ignition switch to the off position and remove the key. 2. Press and release the memory set button located on the driver’s seat. 3. Within 10 seconds, press and release the unlock button on the rke transmitter. To disable another rke transmit...

  • Page 122

    Driver easy exit and easy entry control this additional feature provides automatic driver’s seat positioning which will enhance driver mobility into and out of the vehicle. The seat cushion will move rearward approximately 2.5 in (60 mm) when the key is removed from the ignition switch. The seat wil...

  • Page 123

    2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, before raising the hood. Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latc...

  • Page 124

    Parking lights, instrument panel lights, cargo lights and fog lights (if equipped). Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less suscep- tible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefo...

  • Page 125

    Headlights to turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the o (off) position. Autom...

  • Page 126

    Note: the engine must be running before the head- lights will turn on in the automatic mode. Headlight delay to aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for approximately 90 seconds. This delay is initiated when the ignition is turned off wh...

  • Page 127

    The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pushed a second time, when the headlight sw...

  • Page 128

    Supplement the brightness of the odometer, trip odom- eter, radio and overhead console by rotating the control to the right until you hear a click. This feature is termed the “parade” mode and is useful when headlights are required during the day. Cargo light the cargo lights are turned on by pressi...

  • Page 129

    Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is opened. Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. I...

  • Page 130

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside l...

  • Page 131

    High/low beam switch push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off. Windshield wipers and washers windshield wipers the wipers and wa...

  • Page 132

    Intermittent wiper system the intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay inter...

  • Page 133

    Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist feature push...

  • Page 134

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this war...

  • Page 135

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion, or other physical conditions must exer- cise care when using the steering wheel heater. It may cause burns even at low temperature...

  • Page 136

    • the pedals cannot be adjusted when the vehicle is in reverse or when the electronic speed control sys- tem is on. The following messages will be displayed on vehicles equipped with the electronic vehicle in- formation system (evic) if the pedals are attempted to be adjusted when the system is lock...

  • Page 137

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 138

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the electronic speed control system off when you are not using it. To set a desi...

  • Page 139

    To decrease speed while the electronic speed control is set, push down and hold the set decel lever. If the lever is continually held in the set decel position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and the new set s...

  • Page 140

    Parksense 姞 rear park assist — if equipped the parksense 威 rear park assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to parksense 威 system usage precautions for limitations of...

  • Page 141

    Audible warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Parksense 姞 display when the vehicle is in reverse, the warning display will turn on indicating the system status. Rear parksense 威 display park assist system on 3 understanding the features of your v...

  • Page 142

    The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the evic display will show fewer arcs and the sound tone will change from slow, to fast, to continuous. Park assist system off slow tone 140 und...

  • Page 143

    The vehicle is close to the obstacle when the evic display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: fast tone continuous tone 3 understanding the features of your vehicle 141.

  • Page 144

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none single 1/2 second tone slow fast continuous display message park assist on warning object detected warning object detected ...

  • Page 145

    Approximately five seconds. Refer to “electronic vehicle information center (evic)” in “understanding your instrument panel” for further information. When the shift lever is moved to reverse and the system is disabled, the evic will display the “park assist off” message for as long as the vehicle is...

  • Page 146

    Cleaning the parksense 姞 system clean the parksense 威 sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. Parksense 姞 system usage precautions note: • ensure that the rear bumper is free o...

  • Page 147

    Object as a sensor problem, causing the “service park assist system” message to be displayed in the instrument cluster. • on vehicles equipped with a tailgate, parksense威 should be disabled when the tailgate is in the lowered or open position and the vehicle is in reverse. A lowered tailgate could p...

  • Page 148

    Warning! • drivers must be careful when backing up even when using the parksense 威 rear park assist sys- tem. Always check carefully behind your vehicle, look behind you, and be sure to check for pedes- trians, animals, other vehicles, obstructions, and blind spots before backing up. You are respons...

  • Page 149

    Parkview 姞 rear back up camera — if equipped your vehicle may be equipped with the parkview 威 rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the navigation/multimedia ...

  • Page 150

    Warning! Drivers must be careful when backing up even when using the parkview 威 rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your...

  • Page 151

    Turning parkview 姞 on or off — with navigation/multimedia radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Press the “camera setup” soft-key. 4. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key and pressing the “save” soft-key. ...

  • Page 152

    Overhead console — if equipped the overhead console is located on the headliner above the review mirror. The overhead console contains the following features: • courtesy/reading lights • power sunroof switch — if equipped • power sliding rear window switch — if equipped • universal garage door opene...

  • Page 153

    (rke) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens. Note: the courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the int...

  • Page 154

    Garage door opener — if equipped homelink 威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The homelink 威 unit operates off your vehicle’s battery. The homelink 威 buttons are located...

  • Page 155

    Warning! • your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as...

  • Page 156

    2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the homelink 威 buttons while keeping the evic display in view. For optimal training, point the battery end of the hand- held transmitter away from the homelink 威 3. Simultaneously press and hold both the chosen homelink 威 button and the ha...

  • Page 157

    This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is not the button normally used to open and close the door). 6. Firmly press and release the learn or training button. The name and color of the button may vary by manufacturer. Note: you have 30...

  • Page 158

    Gate operator/canadian programming canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for homelink 威 to pick up the signal during programming. Similar to this canadian law, some u.S. Gate operators ...

  • Page 159

    Reprogramming a single homelink 姞 button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink 威 button for 20 seconds until the evic display states “channel # training.” do not release ...

  • Page 160

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 161

    Warning! • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power win- dows, other controls, or move the vehicle...

  • Page 162

    Position. The sunroof will close fully and stop automati- cally. This is called “express close”. During express close operation, any movement of the switch will stop the sunroof. Closing sunroof — manual mode to close the sunroof, press and hold the switch in the forward position. Any release of the...

  • Page 163

    Sunshade operation the sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Note: the sunshade cannot be closed if the sunroof is open. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound ...

  • Page 164

    Electrical power outlets the auxiliary 12 volt (13 amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 volt power outlets have a cap attached to the outlet indicating “12v dc”, together with either a key symbol or a battery symb...

  • Page 165

    The auxiliary power outlets can be found in the following locations: • lower left and lower right of the center stack — without floor mounted shifter. • inside the top storage tray — with floor mounted shifter. • inside the upper lid of the center storage compartment — if equipped. Power outlet — fl...

  • Page 166

    • rear of the center console storage compartment — quad cab 威 or crew cab. The key symbol indicates that this outlet can supply power when the key is in the on/run or acc posi- tions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect...

  • Page 167

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 168

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 169

    For vehicles equipped with an optional floor shifter. Power inverter — if equipped a 115 volt (150 watts maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power u...

  • Page 170

    Manually press the power inverter button off and on. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. The power inverter switch is located on the switch bank below the climate controls. To turn on the power outlet, press the switch once. Pr...

  • Page 171

    Warning! To avoid serious injury or death: • do not use a three-prong adapter. • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled it may cause an electric shock and failure. Cupholders front instrument pane...

  • Page 172

    Front instrument panel cupholders — floor mounted shifter for vehicles equipped with bucket seats and a floor mounted shifter there are two cupholders located in the floor console. Rear cupholder — quad cab 姞 quad cab 威 vehicles may be equipped with a rear cup- holder that consists of two cup wells ...

  • Page 173

    Rear cupholder — crew cab crew cab vehicles are equipped with rear cupholders located in the center armrest. Storage glove box storage the glove box is located on the passenger side of the instrument panel and features both an upper and lower storage area. Crew cab rear armrest cupholder glove box 1...

  • Page 174

    To open the upper glove box push upward on the handle release. The glove box door will automatically open. To open the lower glove box, pull on the handle to release the latch and lower the door. Upper glove box lower glove box 172 understanding the features of your vehicle.

  • Page 175

    Door storage front door storage — if equipped storage areas and bottle holders (drivers side only) are located in the door trim panels. Rear door storage — crew cab storage compartments are located in both the driver and passenger door trim panels. Front door storage rear door storage 3 understandin...

  • Page 176

    Center storage compartment — if equipped the center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Warning! • this armrest is not a seat. Anyone seated on the armrest could be seri...

  • Page 177

    Pull on the upper handle on the front of the armrest to raise the cover. The upper storage area contains a 12 volt power outlet that can be used to power small electrical devices, refer to “electrical power outlets” for further information. With the upper lid closed, pull on the lower handle to open...

  • Page 178

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injur...

  • Page 179

    Note: the front seat may have to be moved forward to fully open the lid. Seatback storage located in the back of both the driver and passenger front seats are pockets that can be used for storage. Opened storage bin drivers side seatback storage 3 understanding the features of your vehicle 177.

  • Page 180

    Storage (regular cab) the storage bin is located behind the front seats and runs the length of the cab. Storage and seats (crew cab) the crew cab models provide additional storage under the rear seats. Lift the seats to access the storage com- partment. To open the storage compartments, lift upward ...

  • Page 181

    Caution! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids. Plastic grocery bag retainers (regular cab models) retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab...

  • Page 182

    Rear window features rear window defroster the rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. T...

  • Page 183

    Power sliding rear window — if equipped the switch for the power sliding rear window is located on the overhead console. Push the switch to the right to open the glass. Pull the switch to the left to close the glass. Manual sliding rear window — if equipped a locking device in the center of the wind...

  • Page 184

    Unfolding the load floor 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3. Reverse the procedure to store the load floor. Positioning the load floor for storage access under the seat 1. Lift ...

  • Page 185

    2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor. Warning! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious i...

  • Page 186

    Rambox 姞 — if equipped the rambox 威 system is an integrated pickup box storage and cargo management system consisting of three fea- tures: • integrated box side storage bins • cargo extender/divider • bed rail tie-down system rambox 姞 integrated box side storage bins cargo storage bins are located o...

  • Page 187

    Caution! Failure to follow the following items could cause damage to the vehicle: • assure that all cargo inside the storage bins is properly secured. • do not exceed cargo weight rating of 150 lb (68 kg) per bin. To open a storage bin, press and release the button located on the lid. The rambox 威 l...

  • Page 188

    The interior of the rambox 威 will automatically illumi- nate when the lid is opened. In addition to the automatic illumination switch, there is a manual on/off switch located at the rear of each storage bin. Pushing the switch once will turn off the bin lights, pushing the switch again will turn the...

  • Page 189

    Caution! (continued) • loads applied to the top of the bin lid should be minimized to prevent damage to the lid and latching/hinging mechanisms. • damage to the rambox威 bin may occur due to heavy/sharp objects placed in bin that shift due to vehicle motion. In order to minimize potential for damage,...

  • Page 190

    Rambox 威 storage bin cover emergency release lever — if equipped as a security measure, a storage bin cover emergency release is built into the storage bin cover latching mecha- nism. Note: in the event of an individual being locked inside the storage bin, the storage bin cover can be opened from in...

  • Page 191

    To install the bed extender into the storage position, perform the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates. Center handle and lock 1 — center handle lock 2 — handle 3 understanding the feat...

  • Page 192

    2. With the side gates open, position the extender fully forward in the bed against the front panel. 3. Rotate the side gates closed allowing the outboard ends to be positioned in front of the cargo tie down loops. Storage position cargo tie down loop 190 understanding the features of your vehicle.

  • Page 193

    4. Rotate the center handle horizontally to secure the side gates in the closed position. 5. Lock the center handle using the vehicle key to secure the panel into place and assist against theft. Divider position the divider position is intended for managing your cargo and assisting in keeping cargo ...

  • Page 194

    To install the bed extender into a divider position per- form the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates. 2. With the side gates open, position the extender so the outboard ends align with...

  • Page 195

    4. Rotate the center handle horizontally to secure the side gates in the closed position. 5. Lock the center handle to secure the panel into place and assist against theft. Extender position the extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add...

  • Page 196

    To install the bed extender into the extender position perform the following: 1. Lower the tailgate. 2. Make sure the center handle is unlocked and rotate the center handle vertically in order to release the extender side gates. 3. Fit the end of the side gate ends onto the pin and handle. Extender ...

  • Page 197

    4. Rotate the handles to the horizontal position to secure into place. Warning! To reduce the risk of potential injury or property damage: • cargo must be secured. • do not exceed cargo load rating of your vehicle. • secure all loads to truck utilizing cargo tie downs. • extender should not be used ...

  • Page 198

    Bed rail tie-down system caution! The maximum load per cleat should not exceed 250 lbs (113 kg) and the angle of the load on each cleat should not exceed 60 degrees above horizontal, or damage to the cleat or cleat rail may occur. There are two adjustable cleats on each side of the bed that can be u...

  • Page 199

    Out on the cleat and slide it to the detent nearest the desired location. Make sure the cleat is seated in the detent and tighten the nut. To remove the cleats from the utility rail, remove the end cap by pushing up on the locking tab, located on the bottom of the end cap. Slide the cleat off the en...

  • Page 200

    Slide-in campers camper applications certain truck models are not recommended for slide-in campers. To determine if your vehicle is excluded, please refer to the “consumer information truck-camper load- ing” document available from your authorized dealer. For safety reasons, follow all instructions ...

  • Page 201

    2. Remove the connector bracket from the sill by press- ing inward in the locking tab. 3. Disconnect the chassis wiring harness, ensuring the connector bracket does not fall into the sill. 4. Connect the chassis plug and bracket (provided in the glove box) to the chassis wiring harness and insert th...

  • Page 202

    Note: make sure tailgate is supported when removing support cables. 3. Raise the tailgate to a 45 degree angle. 4. Raise the right side of the tailgate until the right side pivot clears the hanger bracket. 5. Slide the entire tailgate to the right to free the left side pivot. 6. Remove the tailgate ...

  • Page 203: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 205 䡵 switch bank button description . . . . . . . . . . . 206 ▫ upper switch bank . . . . . . . . . . . . . . . . . . . 206 ▫ lower switch bank . . . . . . . . . . . . . . . . . . . 207 䡵 instrume...

  • Page 204

    ▫ customer-programmable features (system setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242 䡵 media center 730n/430/430n (rhr/rer/ rbz/rhb) cd/dvd/hdd/nav — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 ▫ operating instructions (voice command system) — if eq...

  • Page 205

    ▫ using this feature . . . . . . . . . . . . . . . . . . . 276 ▫ controlling the ipod威 using radio buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 ▫ play mode . . . . . . . . . . . . . . . . . . . . . . . . . 276 ▫ list or browse mode . . . . . . . . . . . . . . . . . 278 䡵 ipod威/u...

  • Page 206

    ▫ winter operation . . . . . . . . . . . . . . . . . . . . 300 ▫ vacation/storage . . . . . . . . . . . . . . . . . . . . 301 ▫ window fogging and frosting . . . . . . . . . . 301 ▫ outside air intake . . . . . . . . . . . . . . . . . . . 301 ▫ operating tips . . . . . . . . . . . . . . . . . . . . ...

  • Page 207

    Instrument panel features 1 — headlight switch 7 — 115v power inverter outlet 13 — transfer case position switch 2 — instrument cluster 8 — power outlet 14 — ignition switch 3 — radio 9 — lower switch bank 15 — hood release 4 — upper switch bank 10 — cup holders 16 — parking brake release 5 — upper ...

  • Page 208

    Switch bank button description upper switch bank the upper switch bank is located on the center of the instrument panel. 1. Tow/haul refer to “starting and operating” for more information. 2. Esc off refer to “starting and operating” for more information. 3. Hazard warning flasher refer to “what to ...

  • Page 209

    Lower switch bank the lower switch bank is located on the center of the instrument panel. 1. Heated seats refer to “understanding the features of your vehicle” for more information. 2. Ventilated seats refer to “understanding the features of your vehicle” for more information. 3. Heated steering whe...

  • Page 210

    Instrument cluster — base 208 understanding your instrument panel.

  • Page 211

    Instrument cluster — premium 4 understanding your instrument panel 209.

  • Page 212

    Instrument cluster descriptions 1. Tachometer the tachometer indicates engine speed in revolutions per minute (rpm x 1000). Caution! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur. 2. Turn signal indicators the arrow will flash with th...

  • Page 213

    Caution! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear cont...

  • Page 214

    Rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels. For further information on four-wheel drive operation and proper use, refer to “four-wheel drive operation — if equipped” in “starting and operating”. 7. Electronic throttle control...

  • Page 215

    9. 4wd auto indicator the 4wd auto indicator will be illuminated whenever the four-wheel drive mode is auto- matically engaged. 10. Svc (service) 4wd the svc 4wd light monitors the electric shift four-wheel drive system. If the svc 4wd light stays on or comes on during driving, it means that the fou...

  • Page 216

    Note: • the “esc off indicator light” and the “esc activation/malfunction indicator light” come on mo- mentarily each time the ignition switch is turned to on/run. • each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. • the esc system will mak...

  • Page 217

    16. Odometer display / electronic vehicle information center (evic) display area — if equipped odometer display the odometer display shows the total distance the ve- hicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser t...

  • Page 218

    Perform the following: place the ignition in the on/ run, but do not start the engine. With the odometer value displayed, hold the trip button down for a period of six seconds. The odometer will change to trip value first, then it will display the engine hour value. The engine hours will be displaye...

  • Page 219

    Nofuse if the vehicle diagnostic system determines that the ignition off draw (iod) fuse is improperly installed, or damaged, a “nofuse” message will display in the odom- eter display area. For further information on fuses and fuse locations refer to “fuses” in “maintaining your vehicle”. Change oil...

  • Page 220

    Single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass h, the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool. If the light turns on while driving, safely pull over and stop the vehi...

  • Page 221

    Center (evic). Refer to ”electronic vehicle information center (evic) — if equipped” for further information. 20. High beam indicator this indicator shows that headlights are on high beam. Push the multifunction lever forward to switch the headlights to high beam, and pull toward yourself (normal po...

  • Page 222

    Master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the brake booster has been detected by the anti-lock brake system (abs) / electronic stability control (esc) system. In this case, the light will remain on until the condition has been correc...

  • Page 223

    Operation of the brake warning light can be checked by turning the ignition switch from the off position to the on/run position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light ...

  • Page 224

    As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and c...

  • Page 225

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 226

    Although your vehicle will usually be drivable and not need towing, see your authorized dealer for service as soon as possible. Caution! Prolonged driving with the mil on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the mil is flashing, sever...

  • Page 227

    28. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights are on. 29. Anti-lock brake (abs) light this light monitors the anti-lock brake system (abs). The light will turn on when the ignition switch is turned to the on/run position and may stay on for as l...

  • Page 228

    Warning! If the transmission temperature warning light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. For vehicles equipped with a premium cluster this warn- ...

  • Page 229

    For vehicles equipped with a premium cluster this indi- cator will display in the electronic vehicle information center (evic). Refer to ”electronic vehicle information center (evic) — if equipped” for further information. 33. Electronic stability control (esc) off indicator light — if equipped this...

  • Page 230

    This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The evic consists of the following: • system status display • vehicle information warning message displays • customer-programmable features (system setup) • co...

  • Page 231

    Steering wheel evic control button, as it appears on the right side of the steering wheel. Press and release the select button for access to main menus, sub-menus or to select a per- sonal setting in the system setup menu. Press the back button to scroll back to a previous menu or sub-menu. Evic dis...

  • Page 232

    • lights on • keyfob battery low • eco (fuel saver indicator) — if equipped • door(s) ajar (with a single chime, if vehicle is in motion) • wrong key • damaged key • key not programmed • key in ignition • turn signal on • rke battery low • low washer fluid • oil change due > dealer info • park assis...

  • Page 233

    • remote start aborted — fuel low • remote start disabled — system fault • remote start disabled — turn key • remote start active — key to run • remote start disabled — start vehicle to reset • remote start active — insert key and turn to run • memory 1 profile set • memory 2 profile set • memory sy...

  • Page 234

    Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. • charging system light this light shows the status of the electrical charg- ing system. The light should come on when the ignition sw...

  • Page 235

    If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough ...

  • Page 236

    • transmission temperature light this light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation (e.G., sno...

  • Page 237

    Oil change due your vehicle is equipped with an engine oil change indicator system. The oil change due message will flash in the evic display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is du...

  • Page 238

    Will appear whenever the multi-displacement system (mds) (if equipped) allows the engine to operate on four cylinders, or if you are driving in a fuel efficient manner. This feature allows you to monitor when you are driving in a fuel efficient manner, and it can be used to modify driving habits in ...

  • Page 239

    Trip functions press and release the odometer/trip odometer button until one of the following trip functions displays in the evic: • trip a • trip b • elapsed time press the odometer/trip odometer button to cycle through all the trip computer functions. The trip functions mode displays the following...

  • Page 240

    Vehicle info (customer information features) press and release the up or down button until “vehicle info” displays in the evic and press the select button. Press the up and down button to scroll through the available information displays, then press select to display any one of the following choices...

  • Page 241

    Note: • tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kpa) during normal driving conditions. Refer to “tires-general information/tire inflation pres- sures” in “starting and operating” for additional information. • your system...

  • Page 242

    Compass / temperature display the compass readings indicate the direction the vehicle is facing. The evic will display one of eight compass readings and the outside temperature. Note: • the system will display the last known outside tem- perature when starting the vehicle and may need to be driven s...

  • Page 243

    Note: a good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Manual compass calibration if the compass appears erratic and the cal indicator does not appear in the evic display, you must pu...

  • Page 244

    Laptops and radar detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. 1. Turn the ignition switch on. 2. Press the up or down button until the system setup (customer-programmable features) menu is reached, the...

  • Page 245

    Press and release the up or down button until system setup displays in the evic. Use the up or down button to display one of the following choices. Select language when in this display you may select one of five lan- guages for all display nomenclature, including the trip functions and the navigatio...

  • Page 246

    Auto lock doors when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated, or the check-mark...

  • Page 247

    Position using the seat mounted switch. To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Remote start comfort sys. When this feature i...

  • Page 248

    Flash lamps with lock when this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the rke transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection, press and release the select b...

  • Page 249

    Been deactivated. When this feature is deactivated, the system reverts to the standard intermittent wiper operation. Easy exit seat — if equipped when this feature is selected it provides automatic driver seat positioning to enhance driver mobility when enter- ing and exiting the vehicle. To make yo...

  • Page 250

    Highlighted, then press and release the select button until a check-mark appears next to the setting, showing that the setting has been selected. Illuminated approach when this feature is selected, the headlights will activate and remain on for 0, 30, 60, or 90 seconds when the doors are unlocked wi...

  • Page 251

    Media center 730n/430/430n (rhr/rer/rbz/ rhb) cd/dvd/hdd/nav — if equipped note: the sales code is located on the lower right side of the unit’s faceplate. Refer to your uconnect™ multimedia rhr, rer, rbz or rhb user’s manual for detailed operating instructions. Operating instructions (voice command...

  • Page 252

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 253

    4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the ...

  • Page 254

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button press the buttons to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button...

  • Page 255

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 256

    Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 257

    Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek button to move to the next ran- domly selected track. Press the ...

  • Page 258

    • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a three- character extension) • level 2: 31 (including a separator ⬙.⬙ and a three- character extension) multisession disc formats are supported by the radio. Multisession discs may contain combinations...

  • Page 259

    Playlist files are not supported. Mp3 pro files are not supported. Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading time...

  • Page 260

    Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for five seconds (when ignition is off). Media center 130 with satellite radio (sales code res+rsc) note: the radio sales code is located on the lower right side of the radio faceplate. ...

  • Page 261

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the o...

  • Page 262

    If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect phone” message will display on the radio screen. Time button press the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Press and hold the ...

  • Page 263

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either am or fm frequencies. Tune control turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decre...

  • Page 264

    Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast music type inf...

  • Page 265

    Program type 16-digit character display sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in...

  • Page 266

    Window. Select the button (1–6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the set/ rnd button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to e...

  • Page 267

    Inserting compact disc(s) gently insert one cd into the cd player with the cd label facing up. The cd will automatically be pulled into the cd player and the cd icon will illuminate on the radio display. If a cd does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and mu...

  • Page 268

    Note: ejecting with the ignition off is not allowed on convertible or soft-top models (if equipped). Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous se...

  • Page 269

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 270

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 271

    Loading times for playback of mp3 files may be affected by the following: • media - cd-rw media may take longer to load than cd-r media • medium formats - multisession discs may take longer to load than non-multisession discs • number of files and folders - loading times will increase with more file...

  • Page 272

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the aux but...

  • Page 273

    Information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www- .Siriuscanada.Ca for canadian residents. Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic ser...

  • Page 274

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 275

    Additional three seconds will make the radio display the song title all of the time (press and hold again to return to normal display). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) tu...

  • Page 276

    Set button – to set the pushbutton memory when you are receiving a channel that you wish to commit to pushbutton memory, press the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a butt...

  • Page 277

    This feature allows an ipod 威 to be plugged into the vehicle’s sound system through a 16–pin connector, using the provided interface cable. Ipod 威 control supports mini, 4g, photo, nano, 5g ipod威 and iphone 威 devices. Some ipod威 software versions may not fully support the ipod 威 control features. Pl...

  • Page 278

    Using this feature by using the provided connection cable to connect an ipod 威 to the vehicle’s ipod威 control 16–pin connector port: • the ipod威 audio can be played on the vehicle’s sound system, providing metadata (artist, track title, album, etc.) information on the radio display. • the ipod威 can ...

  • Page 279

    • jump backward in the current track by pressing and holding the rw button. Holding the rw button long enough will jump to the beginning of the current track. • jump forward in the current track by pressing and holding the ff >> button. • a single press backward rw or forward ff >> will jump backwar...

  • Page 280

    Shuffle off modes for the ipod 威. If the rnd icon is showing on the radio display, then the shuffle mode is on. List or browse mode during play mode, pressing any of the buttons described below, will bring up list mode. List mode enables scrolling through the list of menus and tracks on the ipod 威. ...

  • Page 281

    • pressing a preset button will display the current list on the top line and the first item in that list on the second line. • to exit list mode without selecting a track, press the same preset button again to go back to play mode . • list button: the list button will display the top level menu of t...

  • Page 282

    Ipod 姞/usb/mp3 control — if equipped note: this section is for sales code res and req/ rel/ret radios only with uconnect™. For sales code rbz/rhb, rhr, rhp, rhw or rb2 touch-screen radio ipod 威/usb/mp3 control feature, refer to the separate rbz/rhb, rhr, rhp, rhw or rb2 user’s manual. Ipod 威/usb/mp3...

  • Page 283

    Once the audio device is connected and synchronized to the vehicle’s ipod 威/usb/mp3 control system (ipod威 or external usb device may take a few minutes to connect), the audio device starts charging and is ready for use by pressing radio switches, as described below. Note: if the audio device battery...

  • Page 284

    Controlling the ipod 姞 or external usb device using radio buttons to get into the ipod 威/usb/mp3 control mode and access a connected audio device, either press the “aux” button on the radio faceplate or press the vr button and say ⬙usb⬙ or ⬙switch to usb⬙. Once in the ipod威/usb/mp3 control mode, aud...

  • Page 285

    During play mode will jump to the next track in the list, or press the vr button and say ⬙next or previous track ⬙. • while a track is playing, press the info button to see the associated metadata (artist, track title, album, etc.) for that track. Pressing the info button again jumps to the next scr...

  • Page 286

    • turning it clockwise (forward) and counterclock- wise (backward) scrolls through the lists, displaying the track detail on the radio display. Once the track to be played is highlighted on the radio display, press the tune control knob to select and start playing the track. Turning the tune control...

  • Page 287

    Device, then follow the same steps to go to the desired track in that list. Not all ipod 威 or external usb device sub-menu levels are available on this system. • music type button: the music type button is another shortcut button to the genre listing on your audio device. Caution! • leaving the ipod...

  • Page 288

    Phone system. Seven devices can be paired to the uconnect™ phone system, but just one can be selected and played. Selecting different audio device 1. Press phone button to begin. 2. After the ⬙ready⬙ prompt and the following beep, say ⬙setup⬙, then ⬙select audio devices⬙. 3. Say the name of the audi...

  • Page 289

    • easy menu-driven functions on touch-screen radios • video and audio input jacks available in rear seating area • nine different medias to choose from in each screen (am, fm, sirius radio, dvd1, dvd2, hard disc drive (hdd), aux in radio, aux1, aux2) the lcd screen is located in the overhead compart...

  • Page 290

    Note: refer to the “uconnect™ multimedia” section of uconnect™ user manual located on the dvd for further details. Steering wheel audio controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. Ves™ r...

  • Page 291

    The right hand control is a rocker type switch with a pushbutton in the center. Pressing the top of the switch will increase the volume, and pressing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to radio, cd or other ...

  • Page 292

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 293

    Throughout the vehicle. The controls are located on the instrument panel below the radio. Note: during snowplow usage on vehicles equipped with outside temperature display, the display may show higher temperatures than the outside ambient tempera- ture. The higher displayed temperature is due to blo...

  • Page 294

    Front blower control there are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position. Note: for vehicles equipped with remote start, the climate controls ...

  • Page 295

    Panel mode air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-level mode air is directed through the panel and floor outlets. Note: there is a difference in temperature (in any conditions other than full cold or full hot), between the upp...

  • Page 296

    Recirculation control press this button to choose between outside air intake or recirculation of the air inside the vehicle. A led will illuminate when you are in recircula- tion mode. Only use the recirculation mode to temporarily block out any outside odors, smoke, or dust, and to cool the interio...

  • Page 297

    Economy mode if economy mode is desired, press the a/c button to turn off the led indicator and the a/c compressor. Rotate the temperature control knob to the desired temperature. Air conditioning operation push this button to engage the air conditioning (a/c). A led will illu- minate when the a/c s...

  • Page 298

    • when occupants in the vehicle select an auto mode operation, auto blower operation is set by using rotary knobs on the control unit and a comfort temperature setting by using the temperature up and down but- tons. • the system provides set-and-forget operation for op- timum comfort and convenience...

  • Page 299

    Automatic operation 1. Position the mode control knob to the auto position on the automatic temperature control (atc) panel. 2. Position the blower control knob in the auto posi- tion on the atc panel. 3. Next, adjust the temperature you would like the system to maintain by adjusting the driver and ...

  • Page 300

    Manual operation this system offers a full complement of manual override features. Note: each of these features operate independently from each other. If any one feature is controlled manually, the temperature doors will continue to operate automati- cally. There are six fixed blower speeds. Use thi...

  • Page 301

    Floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix mode air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while k...

  • Page 302

    Recirculation mode should only be used temporarily. The recirculation led will illuminate on the blower control knob when this button is selected. Push the button a second time to turn off the recirculation mode led and allow outside air into the vehicle. Note: in cold weather, use of recirculation ...

  • Page 303

    Vacation/storage any time you store your vehicle or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in fresh air with the blower setting in high. This will ensure adequate system lubrication to minimize the possibility of ...

  • Page 304

    Operating tips 302 understanding your instrument panel.

  • Page 305: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 309 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 309 ▫ automatic transmission . . . . . . . . . . . . . . . 309 ▫ extreme cold weather (below –20°f or ⫺29°c) . . . . . . . . . . . . . . . 310...

  • Page 306

    ▫ shifting procedure – manually shifted transfer case . . . . . . . . . . . . . . . . . . . . . . . 328 ▫ transfer case position indicator light . . . . . . 329 ▫ electronically shifted transfer case (four-position switch) – if equipped . . . . . . . 329 ▫ shifting procedure . . . . . . . . . . . . ...

  • Page 307

    䡵 driving through water . . . . . . . . . . . . . . . . . 366 ▫ flowing/rising water . . . . . . . . . . . . . . . . . 367 ▫ shallow standing water . . . . . . . . . . . . . . . 367 䡵 off-road driving tips . . . . . . . . . . . . . . . . . . 369 ▫ after driving off-road . . . . . . . . . . . . . . ....

  • Page 308

    ▫ esc activation/malfunction indicator light and esc off indicator light . . . . . . . . . . . . 403 ▫ trailer sway control (tsc) – if equipped . . . 405 䡵 tire safety information . . . . . . . . . . . . . . . . . 406 ▫ tire markings . . . . . . . . . . . . . . . . . . . . . . . 406 ▫ tire identific...

  • Page 309

    ▫ directional tires – if equipped . . . . . . . . . . . 429 ▫ dual rear wheels . . . . . . . . . . . . . . . . . . . . 429 䡵 tire pressure monitor system (tpms) . . . . . . . 430 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . 433 ▫ premium system – if equipped . . . . . . . . . . 435 ...

  • Page 310

    ▫ replacement parts . . . . . . . . . . . . . . . . . . . 451 ▫ maintenance . . . . . . . . . . . . . . . . . . . . . . . . 451 䡵 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . 452 ▫ loose fuel filler cap message . . . . . . . . . . . 453 䡵 vehicle loading . . . . . . . . . . . . . . ...

  • Page 311

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Warnin...

  • Page 312

    Extreme cold weather (below –20°f or ⫺29°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If engine fails to start if the engine fails to start after you have followed the “normal...

  • Page 313

    If the engine has been flooded, it may start to run, but not have enough power to continue running when the key fob is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key fob once the engine is running smoo...

  • Page 314

    Warning! Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 volt electrical cord could cause electrocution. Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the ve...

  • Page 315

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the shift lever to be placed in park prior to turning the key fob to the lock position. The key fob can only be removed from the ignition switch when the ignition is in the lock position. Once th...

  • Page 316

    Gear ranges do not race the engine when shifting from park or neutral position into another gear range. Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use park while the vehicle is in motion. Apply the parking brake when leav...

  • Page 317

    Warning! (continued) • unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into park, remove the key fob from the ignition, a...

  • Page 318

    Transmission will automatically shift from third gear to overdrive if the following conditions are present: • the shift lever is in drive • the engine coolant has reached normal operating tem- perature • vehicle speed is above approximately 30 mph (48 km/h) • the tow/haul switch has not been activat...

  • Page 319

    Operating in tow/haul mode, the transmission will shift to third gear and fourth gear will be enabled under steady cruise conditions. The “tow/haul indicator light” will illuminate in the instrument cluster to indicate when the switch has been activated. Pressing the switch a second time restores no...

  • Page 320

    5. Move the shift lever to the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. If the problem persists, park, reverse, and neutral will continue to oper- ate. Only second gear will operate in the drive position. Have the transmission checke...

  • Page 321

    Into 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second gear) or 1 (first gear), when needed. On vehicles equipped with 4.7l or 5.7l engines, use of ers (or tow/haul mode) also enables an additional underdrive gear which is not normally used during th...

  • Page 322

    Through third gear are underdrive gears, and fourth gear is direct drive. Ers fifth gear (overdrive) is the same as the normal fourth gear. When in the drive position in first through fourth gear, the first tap down (-), will display the ers designation for the current gear (the transmission will no...

  • Page 323

    Gear ranges do not race the engine when shifting from park or neutral position into another gear range. Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use park while the vehicle is in motion. Apply the parking brake when leav...

  • Page 324

    Warning! (continued) • unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into park, remove the key fob from the ignition, a...

  • Page 325

    Overdrive operation the overdrive automatic transmission contains an elec- tronically controlled fourth and fifth gear (overdrive). The transmission will automatically shift from drive to overdrive if the following conditions are present: • the shift lever is in drive; • the engine coolant (antifree...

  • Page 326

    Performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in the tow/haul mode, fifth gear is dis- abled and 2-3 and 3-4 shift patterns are modified. Shifts into overdrive (fourth gear) are allowed during steady cruise (for improved fuel e...

  • Page 327

    Note: • the torque converter clutch will not engage until the transmission fluid and engine coolant (antifreeze) are warm [usually after 1 to 3 miles (1.6 to 4.8 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is...

  • Page 328

    When additional traction is required, the 4h and 4l positions can be used to lock the front and rear drive- shafts together and force the front and rear wheels to rotate at the same speed. This is accomplished by simply moving the shift lever to the desired positions. The 4h and 4l positions are int...

  • Page 329

    Note: delayed shifts out of four-wheel drive may be experienced due to uneven tire wear, low or uneven tire pressures, excessive vehicle loading, or cold tempera- tures. Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the neutral position without...

  • Page 330

    4l four-wheel drive low range - this range locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Shifting procedure – manually ...

  • Page 331

    Method is with the vehicle rolling 2 to 3 mph (3 to 5 km/h). Avoid attempting to engage or disengage 4l with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h). • do not attempt to shift into or from 4l while the transmission is in gear. Transfer case position indicator light the “transfer case...

  • Page 332

    This electronically shifted transfer case provides four mode positions: • two-wheel drive high range (2wd) • four-wheel drive lock range (4wd lock) • four-wheel drive low range (4wd low) • neutral (neutral) this electronically shifted transfer case is designed to be driven in the two-wheel drive pos...

  • Page 333

    If all shift conditions are met: 1. The current position indicator light will turn off. 2. The selected position indicator light will flash until the transfer case completes the shift. 3. When the shift is complete, the indicator light for the selected position will stop flashing and remain on. If o...

  • Page 334

    Note: do not attempt to make a shift while only the front or rear wheels are spinning, as this can cause damage to driveline components. When operating your vehicle in 4wd low, the engine speed is approximately three times that of the 2wd or 4wd lock positions at a given road speed. Take care not to...

  • Page 335

    4wd lock four-wheel drive lock range - this range locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. This range provides additional traction for loose, slippery road surfaces only. 4wd low four-wheel drive low range - this range provides low ...

  • Page 336

    2wd ⇔ 4wd lock rotate the 4wd control switch to the desired position. Shifts between 2wd and 4wd lock can be done with the vehicle stopped or in motion. With the vehicle in motion, the transfer case will engage/disengage faster if you momentarily release the accelerator pedal after turn- ing the con...

  • Page 337

    Alternate procedure 1. Bring the vehicle to a complete stop. 2. With the ignition switch in the on position and the engine either off or running, shift the transmission into neutral. 3. Rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ...

  • Page 338

    Electronically shifted transfer case (five-position switch) – if equipped this is an electronic shift transfer case and is operated by the 4wd control switch (transfer case switch), which is located on the instrument panel. This electronically shifted transfer case provides five mode positions: • tw...

  • Page 339

    Drive will be automatically engaged when the vehicle senses a loss of traction. Because the front axle is en- gaged, this mode will result in lower fuel economy than the 2wd mode. When additional traction is required, the transfer case 4wd lock and 4wd low positions can be used to lock the front and...

  • Page 340

    If one or more shift conditions are not met: 1. The indicator light for the current position will remain on. 2. The newly selected position indicator light will con- tinue to flash. 3. The transfer case will not shift. Note: before retrying a selection, make certain that all the necessary requiremen...

  • Page 341

    Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the drivetrain. Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do ...

  • Page 342

    4wd low four-wheel drive low range - this range provides low speed four-wheel drive. Locks the front and rear drive- shafts together forcing the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 m...

  • Page 343

    The vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelera- tor pedal after turning the control switch. If the vehicle is stopped, the ignition switch must be in the on position with the engine either running or off. This shift cannot be completed ...

  • Page 344

    Note: • if steps 1 or 2 of either the preferred or alternate procedure are not satisfied prior to attempting the shift or if they no longer are being met while the shift attempt is in process, the desired position indicator light will flash continuously while the original posi- tion indicator light ...

  • Page 345

    Caution! (continued) • do not try to lock the rear axle if the vehicle is stuck and the tires are spinning. You can damage drivetrain components. Lock the rear axle before attempting situations or navigating terrain, which could possibly cause the vehicle to become stuck. The locking axles are contr...

  • Page 346

    Lock or front/rear lock position, drive the ve- hicle in a turn or on loose gravel to expedite the locking action. Warning! Do not use the locked axle position for normal driving. A locked front axle is intended for off-road driving only. Locking the front axle during on-road driving will reduce the...

  • Page 347

    Due to the use of taller springs, this vehicle has an increased ride height of approximately 1.9 in (48.3 mm) in the front and 1.5 in (38.1 mm) in the rear. A major advantage to increasing ride height is the positive effect it has on approach/departure and break over angles. This system is controlle...

  • Page 348

    Warning! Do not disconnect the stabilizer bar and drive on hard surfaced roads or at speeds above 18 mph (29 km/h), you may lose control of the vehicle, which could result in serious injury. The front stabilizer bar enhances vehicle stability and is necessary for main- taining control of the vehicle...

  • Page 349

    Warning! If the stabilizer/sway bar will not return to on-road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury. Contact your loca...

  • Page 350

    Distance up the ramp divided by the wheelbase of the vehicle and multiplied by 1,000 is the rti. This vehicle has an rti of 655, which means you can articulate one front wheel 32 inches in the air while the other three wheels remain in contact with the ground. Water fording characteristics water for...

  • Page 351

    Your vehicle’s steering, handling and traction. Control- ling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture. Avoid sudden accelerations, turns or braking. In most cases there are no road signs, pos...

  • Page 352

    Driving in snow, mud and sand there is a drastic reduction in traction when driving in snow, mud or sand. The vehicle will be less responsive to steering, acceleration and braking inputs. Therefore you should accelerate slowly, leave greater stopping distances and avoid abrupt vehicle maneuvers. You...

  • Page 353

    • sand – soft sand is very difficult to travel through with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum and do not stop. The key to driving in soft sand using the appropriate tire pressure, accelerating slowly, avoid- ing abrupt maneuvers and mainta...

  • Page 354

    Forward until it makes contact with the object. Apply the throttle lightly while holding a light brake pressure and ease the vehicle up and over the object. Warning! Crossing obstacles can cause abrupt steering system loading which could cause you to loose control of your vehicle. Using a spotter th...

  • Page 355

    Independently. You need to use caution when crossing large obstacles with steep sides. Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover. If you get caught in a rut, dig a small trench to the right or left at a 45-degree ang...

  • Page 356

    Caution! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Hill climbing hill climbing requires good judgment and a good under- standing of your abilities and your vehicle’s limitations. Hills can cause serious problems. Some are just too steep to climb and sho...

  • Page 357

    Fresh ⬙bite⬙ into the surface and will usually provide enough traction to complete the climb. If you do not make it to the top, place the vehicle in reverse and back straight down the grade using engine resistance along with the vehicle brakes. Warning! Never attempt to climb a hill at an angle or t...

  • Page 358

    Sure the surface has good traction with firm and stable soils. If possible transverse the incline at an angle heading slightly up or down. Warning! Driving across an incline increases the risk of a rollover, which may result in severe injury. • if you stall or begin to lose headway – if you stall or...

  • Page 359

    Your vehicle’s abilities and be able to recover it if something goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake. If the engine stalls do not attempt to restart it. Determine if it has ingested water first. The key ...

  • Page 360

    Crossing is the water depth, current and bottom con- ditions. On soft bottoms the vehicle will sink in, effectively increasing the water level on the vehicle. Be sure to consider this when determining the depth and the ability to safely cross. • crossing puddles, pools, flooded areas or other standi...

  • Page 361

    Downstream out of control if the water is deep enough to push on the large surface area of the vehicle’s body. Before you proceed determine the speed of the current, the water’s depth, approach angle, bottom condition and if there are any obstacles, then cross at an angle heading slightly upstream u...

  • Page 362

    Vehicle recovery if you drive off-road, you may encounter a situation where you will need to recover your vehicle. Vehicle recovery should always be given consideration before attempting a questionable obstacle. You should never go off-road driving without the ability to recover your vehicle from a ...

  • Page 363

    Vehicle from drive to reverse, while applying throttle after each shift. During this process, for addi- tional traction, try turning your steering wheel quickly back and forth no more than a 1 ⁄ 4 turn. If you are stuck in mud, sand, or snow try spinning your tires during this process to clean the d...

  • Page 364

    Two tow straps together using a 1 1 ⁄ 2 inch hard wood dowel. This will keep the straps from becoming knot- ted and is safer than using a clevis pin if the strap breaks. Next have the tow vehicle backup, leaving two to three feet worth of slack in the strap. Then the tow vehicle, using light throttl...

  • Page 365

    Out of the situation in a slow controlled manner. This control works well for avoiding further vehicle dam- age. Once you decide it is time to use the winch look for a good anchor point. It needs to be strong enough to hold more than the vehicle’s weight and provide a direction of pull as straight a...

  • Page 366

    Always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiato...

  • Page 367

    Limited-slip differential the limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-...

  • Page 368

    Erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the rear (driving) wheels. Warning! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehi...

  • Page 369

    Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow- ing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicl...

  • Page 370

    Caution! (continued) • driving through standing water may cause dam- age to your vehicle’s drivetrain components. Al- ways inspect your vehicle’s fluids (i.E., engine oil, transmission, axle, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through st...

  • Page 371

    Off-road driving tips care should be taken when attempting to climb steep hills or driving diagonally across a hill or slope. If natural obstacles force you to travel diagonally up or down a hill, choose a mild angle and keep as little side tilt as possible. Keep the vehicle moving and make turns sl...

  • Page 372

    • after extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. ...

  • Page 373

    2. Attach the hook to a suitable anchor point. Caution! Be certain the anchor will withstand the load re- quired to tension the wire rope. 3. Apply at least 500 lbs (227 kg) of tension to the rope while winding the rope. Always use care to ensure the rope does not pile up on one side of the drum and...

  • Page 374

    Understanding the features of your winch winch components 372 starting and operating.

  • Page 375

    1. Motor: the winch motor is powered by the vehicle charging system and features a thermal protection switch that automatically stops motor function in the power-in direction if the motor gets too hot. 2. Remote socket: the remote socket allows the remote control to be attached to the control pack t...

  • Page 376

    Winch accessories the following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: wire rope, through use, will develop ⬙barbs⬙ which can slice skin. It is ex- tremely important to wear protective gloves while oper- ating the winch or h...

  • Page 377

    Clevis/d-shackles: the d-shackle is a safe means of connecting the looped ends of cables, straps and snatch blocks. The shackle’s pin is threaded to allow easy re- moval. Tree trunk protector: typi- cally made of tough, high- quality nylon, it provides the operator an attachment point for the winch ...

  • Page 378

    Warning! (continued) • always stand clear of wire rope and load and keep others away during winching. • always keep hands and clothing clear of the wire rope, hook and fairlead opening during operation and when spooling. • never wrap wire rope back onto itself. Always use a choker chain, wire choker...

  • Page 379

    General information practice using your winch before you get stuck. Some key points to remember when using your winch are: 1. Always take your time to assess the situation and plan your pull carefully. 2. Always take your time when using a winch. 3. Use the right equipment for the situation. 4. Alwa...

  • Page 380

    Caution! (continued) • inspect for cracks, pinches, frayed wires, or loose connections. Replace if damaged. • be careful not to pull the winch cable collar through the rollers. Watch and listen to winch for proper snugness. 1. Inspect the winch, winch mount, and wire rope for damage. Do not use the ...

  • Page 381

    4. Free the winch hook and attach the hook strap. Free the winch hook from its anchor point. Attach the hook strap to the hook (if not attached). Free spool hook strap 5 starting and operating 379.

  • Page 382

    5. Pull the wire to the anchor point. Pull out enough wire rope to reach your anchor point. Be sure to keep a certain amount of tension on the wire as it can become twisted and over-wrapped when slackened, leading to wire rope damage. To prevent losing the end, hold the hook strap while you work. 6....

  • Page 383

    Caution! Always be certain the anchor you select will with- stand the load. Note: how to choose an anchor point: a secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural an- chors include trees, stumps and rocks. Hook the cable as low as pos...

  • Page 384

    Note: always ensure the clutch is fully engaged or disengaged. 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in front of the winch. If you choose to control the winch from inside your vehicle, always pass...

  • Page 385

    11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure. 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope. 5 starting and operating 383.

  • Page 386

    13. In certain situations you may decide to throw a heavy blanket or similar object over the wire rope. A heavy blan- ket can absorb energy should the wire rope break. Place it on the wire rope midway be- tween the winch and the an- chor point. Do this before the wire rope is put under ten- sion. Do...

  • Page 387

    For additional assistance, the winched vehicle can be slowly driven while being pulled by the winch. Continue pulling until the vehicle is on stable ground. If you are able to drive the vehicle, the winching operation is complete. Note: • avoid overheating the winch motor. For extended winching, sto...

  • Page 388

    Section of the rope and reposition it to the opposite end of the drum, which will free up space for continued winching. 16. Secure vehicle. Once recovery of the vehicle’s is complete, be sure to secure the vehicle’s brakes and put the transmission in park. Release tension in the wire rope. 17. Disco...

  • Page 389

    Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered. Tighten and straighten the layer if necessary. Keep the wire rope under light tension and spool the wire rope back and onto the winch drum in even...

  • Page 390

    Rigging techniques various winching situations will require application of other winching techniques. These could range from too little distance to achieve maximum pull using straight line rigging, simply increasing pulling power, or main- taining a straight-line pulling situation. You will have to ...

  • Page 391

    Will enable you to change your pulling direction while still allowing the wire rope to be at 90° to wind properly onto the spooling drum. Increasing pulling power in some cases, you may find yourself needing more pulling power. The use of snatch blocks increases me- chanical advantage and that incre...

  • Page 392

    Vehicle’s frame/tow hook and run the wire rope through a snatch block. Disengage the clutch and, using the snatch block, pull out enough wire to reach your anchor point. Do not attach the hook to the mounting kit. Secure to the anchor point with a tree trunk protector or choker chain. Attach the cle...

  • Page 393

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Power steering fluid check checking the power steering fluid level at a define...

  • Page 394

    If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Multi-displacement system (mds) (if equipped) — 5.7l engine only thi...

  • Page 395

    When the parking brake is applied with the ignition switch on, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the transmis- sion is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sou...

  • Page 396

    Warning! (continued) • be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave the transmission in...

  • Page 397

    Note: under cold temperatures, pedal effort will be higher than normal until the power steering fluid reaches operating temperature. Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes anti-lock brake sys- tem (abs), traction contro...

  • Page 398

    Traction control system (tcs) – if equipped the tcs monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s), and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs function...

  • Page 399

    Warning! • the bas cannot prevent the natural laws of phys- ics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the bas cannot prevent collisions, including those resulting from exces...

  • Page 400

    • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphill is in reverse gear). Warning! There may be situations on minor hills (i.E., less than 7%), with a loaded vehicle or while pulling a trailer where the system will not activate a...

  • Page 401

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision w...

  • Page 402

    3. With the engine running and the brake applied, rotate the steering wheel 180° counterclockwise from center. 4. Press the “esc off” switch four times within 20 sec- onds. The “esc off indicator light” should appear and disappear four times. 5. Rotate the steering wheel 360° clockwise (180° clock- ...

  • Page 403

    The intended path, esc applies the brake of the appro- priate wheel to assist in counteracting the oversteer or understeer condition. • oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • understeer - when the vehicle is turning less than appropriate for ...

  • Page 404

    Mode by pressing the “esc off” switch. Once the situa- tion requiring esc to be switched to the “partial off” mode is overcome, turn esc back on by momentarily pressing the “esc off” switch. This may be done while the vehicle is in motion. Warning! In the “partial off” mode, the engine torque reduc-...

  • Page 405

    Into the park position from any other position and then moved out of the park position. This will occur even if the message was previously cleared. In this mode, esc and tcs except for the “limited slip” feature described in the tcs section are turned off until the vehicle reaches a speed of 40 mph ...

  • Page 406

    Light” comes on continuously with the engine running, a malfunction has been detected in the esc system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as...

  • Page 407

    Trailer sway control (tsc) – if equipped the tsc system uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appro- priate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appropriate wheel(s) to counteract the sw...

  • Page 408

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 409

    Tires designed to this standard have the letter “t” molded into the sidewall preceding the size designa- tion. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing ...

  • Page 410

    Example: 15 = rim diameter in inches (in) service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating cond...

  • Page 411

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 412

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire pressure cold tire inflation pressure is defined as the tire pressure after ...

  • Page 413

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total wei...

  • Page 414

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 415

    Available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in ste...

  • Page 416

    414 starting and operating.

  • Page 417

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 418

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 419

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire infl...

  • Page 420

    Loading may be required for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. Warning! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on ...

  • Page 421

    Spare tire matching original equipped tire and wheel – if equipped your vehicle may be equivalent with a spare tire and wheel in look and function as the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehic...

  • Page 422

    Since this tire has limited tread life the original equip- ment tire should be repaired (or replaced) and reinstalled on your vehicle at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically fo...

  • Page 423

    Your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than ...

  • Page 424

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 425

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 426

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 427

    Tire chains use “class s” chains, or other traction aids that meet sae type “s” specifications. Use “class u” chains on 2500/3500 model trucks, or other traction aids that meet sae type “u” specifica- tions. Note: chains must be the proper size for the vehicle as recommended by the chain manufacture...

  • Page 428

    Caution! (continued) • do not install tire chains on front wheels of 4x2 vehicles. • do not drive for a prolonged period on dry pave- ment. • observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower sug- gested oper...

  • Page 429

    Caution! Do not use tire chains on the front wheels of any model except for 3500 drw (dual rear wheel) trucks equipped with lt235/80r17e tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle. Do not use tire chains on the rear wheels ...

  • Page 430

    Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation are...

  • Page 431

    Directional tires – if equipped for the r/t package with 22” tires & wheels, tire rotation must be performed with consideration of the tire rotation direction. The recommended rotation pattern for direc- tional tires is shown below. Dual rear wheels the tires used on dual wheel assemblies should be ...

  • Page 432

    Caution! 3500 dual rear tires have only one approved direc- tion of rotation. This is to accommodate the asym- metrical design (tread pattern) of the on/off-road tire and the use of outline white letter (owl) tires. • when replacing a flat, the spare tire may have to be remounted on the rim, or inst...

  • Page 433

    The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire. The tpms will continue to warn the driver of low tire pressure as long as the condition e...

  • Page 434

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when us- ing replacement equipment that is not of the same size, t...

  • Page 435

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system the tire pressure monitor system (tpms) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wh...

  • Page 436

    Turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. Check tpms warning if a system fault is detected, the tpm telltale light will flash on and off for 75 seconds and then remain on solid. The system fault will als...

  • Page 437

    Premium system – if equipped the tire pressure monitor system (tpms) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the receiver module. Note: it is particu...

  • Page 438

    Tire pressure monitoring low pressure warnings the tpm telltale light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the evic will display one or more low pressure messages (left front, left rear, ...

  • Page 439

    Turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. Check tpms warning if a system fault is detected, the tpm telltale light will flash on and off for 75 seconds and then remain on solid. The system fault will als...

  • Page 440

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tpm telltale light will no longer flash, and the ⬙check tpm system⬙ message will no longer display, and a pressure value will display in place of the dashes...

  • Page 441

    Tire pressure monitor system (tpms) tire light load inflation switch description (2500 models) – if equipped warning! Never operate your vehicle with the tpms and tire pressures set to the light load inflation pressure settings if carrying more than two occupants (150 lbs [68 kg] each) plus 200 lbs ...

  • Page 442

    Load inflation switch led is on, the tpms is using the light load inflation pressure (cold) low inflation warning thresholds. Tire light load inflation switch operation – if equipped • this vehicle may have different recommended tire pressure values between the front and rear tires as shown in both ...

  • Page 443

    To switch from the max load inflation pressure (cold) low pressure warning threshold to the light load inflation pressure (cold) low pressure warning threshold, begin by placing the ignition switch in the run position. Next, lower all four road tire pressures to the light load inflation pressure val...

  • Page 444

    The rear face of the driver door. Using an accurate tire pressure gauge, re-check the tire pressures for the light load inflation pressure (cold) value. Warning! It is the driver’s responsibility to change to the max load inflation pressure (cold) low pressure warning threshold condition when not dr...

  • Page 445

    • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesired operation. The tpm sensors are regulated under one of the follow- ing licenses: united states . . . . . . . . . . . . . . . . . . . . . Kr5s120123 ca...

  • Page 446

    As hard starting, stalling, and hesitations. If you experi- ence these symptoms, try another brand of gasoline before considering service for the vehicle. Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) which defin...

  • Page 447

    Problems that result from using gasoline containing methanol or gasoline containing more than 10% ethanol are not the responsibility of the manufacturer and may not be covered under warranty. E-85 usage in non-flex fuel vehicles non-ffv vehicles are compatible with gasoline contain- ing 10% ethanol ...

  • Page 448

    Of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether or not his/her gasoline contains mmt. It is even more important to look for gasolines without mmt in canada, because mmt can be used at levels higher than those allowed in the united state...

  • Page 449

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers are not recommended. Most of these products contain high concentra- tions of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the respon...

  • Page 450

    Warning! (continued) • guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly. Until repaired, drive with all side windows fully open. Flexible fuel (4.7l engine only) — if equipped e...

  • Page 451

    Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap)...

  • Page 452

    • you do not add less than 5 gallons (19 liters) when refueling • you operate the vehicle immediately after refueling for a period of at least 5 minutes observing these precautions will avoid possible hard starting and/or significant deterioration in driveability during warm up. Note: • when the amb...

  • Page 453

    Note: use of the engine block heater (if equipped) is beneficial for e-85 startability when the ambient tempera- ture is less than 32°f (0°c). Cruising range because e-85 fuel contains less energy per gallon/liter than gasoline, you will experience an increase in fuel consumption. You can expect you...

  • Page 454

    Adding fuel the fuel filler cap (gas cap) is located behind the fuel filler door, on the left side of the vehicle. Open the fuel door and remove the fuel cap by turning it counter- clockwise. Note: when removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler door. Ca...

  • Page 455

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel to the vehicle when the engine is running. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be bu...

  • Page 456

    This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle weight rating (gawr) front and rear, and vehicle identification number (vin). A month-day-hour (mdh) number is included on this label and indicates the month, day and hour of manufacture. The bar co...

  • Page 457

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 458

    Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. Trailer towing in th...

  • Page 459

    Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Note: the gcwr rating includes a 150 lbs (68 kg) allowance for the presence of a driver. Gross axle weight rating (gawr) the gawr is the maximum capacity of the fr...

  • Page 460

    That typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connec...

  • Page 461

    Example — without weight-distributing hitch (incorrect) example — with weight-distributing hitch (correct) 5 starting and operating 459.

  • Page 462

    Fifth-wheel hitch the fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. It connects a vehicle and fifth-wheel trailer with a coupling king pin. Gooseneck hitch the gooseneck hitch employs a pivoted coupling arm which atta...

  • Page 463

    Weight ratings)” for the website address that contains the necessary information for your specific drivetrain. Trailer hitch classification definitions class max. Trailer hitch industry standards class i - light duty 2,000 lbs (907 kg) class ii - medium duty 3,500 lbs (1587 kg) class iii - heavy dut...

  • Page 464

    Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gtw on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause lo...

  • Page 465

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to “tire safety information/tire and loading in- formation placard” i...

  • Page 466

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 467

    Warning! (continued) 2. Gtw 3. Gawr 4. Trailer tongue weight rating for the trailer hitch utilized (this requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing requirements – tires • do not attempt to tow a trailer w...

  • Page 468

    Actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). Caution! If the trailer weigh...

  • Page 469

    Note: this module has been designed and verified for electric trailer brakes. To determine the type of brakes on your trailer, check with your trailer manufacturer or dealer. The user interface consists of the following: gain/ brake output power display shows the current gain setting. This display m...

  • Page 470

    Lever is activated while the brake is also applied, the greater of the two inputs determines the power sent to the trailer brakes. The trailer and the vehicle’s brake lamps will come on when either vehicle braking or manual trailer brakes are applied. Trailer brake status indicator light this light ...

  • Page 471

    1. Make sure the trailer brakes are in good working condition, functioning normally, and properly adjusted. See your trailer dealer if necessary. 2. Hook up the trailer and make the electrical connec- tions according to the trailer manufacturer’s instructions. 3. When a trailer with electric brakes ...

  • Page 472

    Caution! The itbm module has been designed and verified for electric trailer brakes. Connecting a trailer that is not compatible with the itbm system may result in reduced or complete loss of trailer braking. There may be a increase in stopping distance or trailer instability which could result in d...

  • Page 473

    Note: do not cut or splice wiring into the vehicle’s wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ...

  • Page 474

    Warning! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automo- tive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. Towing tips before setting out on a trip, practice turni...

  • Page 475

    Note: using “tow/haul” mode or a lower gear range while operating the vehicle under heavy operating conditions will improve performance and extend trans- mission life by reducing excessive shifting and heat build up. This action will also provide better engine braking. The automatic transmission flu...

  • Page 476

    − air conditioning turn off temporarily. Snowplow 1500 models only note: do not use this model vehicle for snowplow applications. Warning! Snowplows and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the fro...

  • Page 477

    Builders guide. See your authorized dealer, installer or snowplow manufacturer for this information. There are unique electrical systems that must be connected to properly assure operator safety and prevent overloading vehicle systems. Warning! Attaching a snowplow to this vehicle could adversely af...

  • Page 478

    2. The total gvwr or the front gawr or the rear gawr should never be exceeded. 3. Cargo capacity will be reduced by the addition of options or passengers, etc. The loaded vehicle weight, including the snowplow system, all aftermarket accessories, driver, passengers, options, and cargo, must not exce...

  • Page 479

    Operating tips under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating speed. The operator should be familiar with the area and surface to be cleaned. Reduce speed and use extreme caution when plowing unfamiliar areas or under poor visibility. Note: during snowplow usage on...

  • Page 480

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models flat tow none not allowed see instructions • automatic transmission in park • manual transmission in gear (not in neutral (n) ...

  • Page 481

    Recreational towing – two-wheel drive models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is allowed only if the rear wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly...

  • Page 482

    Must be placed in gear (not in neutral) for recre- ational towing. Refer to the following for the proper transfer case neutral shifting procedure for your vehicle. Caution! • front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or r...

  • Page 483

    Shifting into neutral (n) – manual shift transfer case (if equipped) use the following procedure to prepare your vehicle for recreational towing. Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engagin...

  • Page 484

    8. Release the brake pedal (and clutch pedal on manual transmissions) for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with automatic transmission in drive or manual transmission in first gear. 10. Turn off the engine. 11. Firmly apply the parking brake. 12. Shi...

  • Page 485

    6. Shift the transfer case lever to the desired position. Note: when shifting out of transfer case neutral (n), turning the engine off may be required to avoid gear clash. 7. Shift the automatic transmission into park, or place manual transmission in neutral. 8. Release the brake pedal. 9. Disconnec...

  • Page 486

    Caution! It is necessary to follow these steps to be certain that the transfer case is fully in neutral before recre- ational towing to prevent damage to internal parts. 1. Bring the vehicle to a complete stop. Shift automatic transmission into park. 2. Turn off the engine. 3. Turn the ignition swit...

  • Page 487

    14. Shift the transmission into park or place manual transmission in gear (not in neutral). Caution! Damage to the transmission may occur if the trans- mission is shifted into park with the transfer case in neutral and the engine running. With the transfer case in neutral, ensure that the engine is ...

  • Page 488

    Shifting out of neutral – electronic shift transfer case (if equipped) use the following procedure to prepare your vehicle for normal usage: 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake. 3. Insert the key fob into the ignition ...

  • Page 489

    15. Shift the transmission into gear, release the brake pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally. Note: • steps 1 through 5 are requirements that must be met prior to pressing the transfer case neutral button and must continue to be met until the...

  • Page 491: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 491 䡵 jacking and tire changing . . . . . . . . . . . . . . . 491 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 492 ▫ removing the spare tire . . . . . . . . . . . . . . . 497 ▫ preparations ...

  • Page 492

    䡵 towing a disabled vehicle . . . . . . . . . . . . . . . 518 ▫ towing without the ignition key fob . . . . . 519 ▫ two-wheel drive models . . . . . . . . . . . . . . 520 ▫ four-wheel drive vehicles . . . . . . . . . . . . . . 520 490 what to do in emergencies.

  • Page 493

    Hazard warning flashers the hazard warning flasher switch is located on the upper switch bank just below the radio. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press...

  • Page 494

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack location the jack and jack tools are stored und...

  • Page 495

    Jack and tools (1500 series) jack and tools (2500/3500 series) 6 what to do in emergencies 493.

  • Page 496

    Warning! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious in...

  • Page 497

    Folding flap and rolling bag tying bag to jack with straps 6 what to do in emergencies 495.

  • Page 498

    4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor, and then secure to the floor pan using the wing bolt. Reinstall the plastic cover. Jack and tools tied j...

  • Page 499

    Removing the spare tire remove the spare tire before attempting to jack up the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube. Rotate the wheel wrench handle cou...

  • Page 500

    It is recommended that you stow the flat or spare to avoid tangling the loose cable. Note: the winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Preparations 1. Park the vehicle on a firm, lev...

  • Page 501

    Instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the wheel di...

  • Page 502

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise...

  • Page 503

    Operate the jack using the jack drive tube and the wheel wrench. The tube extension may be used but is not required. For 4x2 and 4x4 trucks, when changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle between th...

  • Page 504

    Caution! Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. • 2500/3500 series trucks for 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wh...

  • Page 505

    Jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube extension and wheel wrench. For 4x2 and 4x4 trucks, when changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the...

  • Page 506

    Caution! Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. Note: if the bottle jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to low...

  • Page 507

    Warning! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Al- ways stow the jack parts and the extra tire and wheel in the places provided. 7. Install the wheel center cap and remove the wheel blocks. Do not install chrome or aluminum wheel center ...

  • Page 508

    Caution! • use a back-and-forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap finish may occur. • the rear hub caps on the dual rear wheel has two pry-off notches. Make sure that the hook of the jack handle driver is located squarely in t...

  • Page 509

    Disc wheels type nut stud size torque ft. Lbs. Torque newton meters cone 9/16-18 120-150 160-200 flanged 9/16-18 130-160 190-220 8-stud — dual rear wheels dual wheels are flat-mounted and center-piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these...

  • Page 510

    Dual wheel models require a special heavy-duty lug nut tightening adapter (included with the vehicle) to cor- rectly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device. Note: when installing a spare tire as part of a dual rear...

  • Page 511

    Second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). It is recommended that wheel stud nuts be kept torqued to specifications at all times. Torque wheel stud nuts to specifications at each lubrication interval. ...

  • Page 512

    Hoisting a conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking loca- tions. However, a floor jack or frame hoist must never be used on any other parts of the underbody. Caution! Never use a floor jack directly under the differential housing of a load...

  • Page 513

    Note: the positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan bla...

  • Page 514

    3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-start...

  • Page 515

    Warning! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then st...

  • Page 516

    Freeing a stuck vehicle if the vehicle becomes stuck in snow, sand or mud, it can often be moved by a rocking motion. Move the shift lever rhythmically between drive and reverse while ap- plying slight pressure to the accelerator. In general, the least amount of accelerator pedal pressure to maintai...

  • Page 517

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 518

    Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use one of the following procedures to temporarily move the shift lever: column shifter — if equipped 1. Firmly set the parking brake. 2. Turn the ignition switch to the on/run position...

  • Page 519

    Center console shifter — if equipped to access the override, carefully remove (using a flat- bladed screwdriver) the override access cover which is located on the right of the shift lever gate. 1. Firmly set the parking brake. 2. Turn the ignition switch to the on/run position without starting the e...

  • Page 520

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the trans- mission and drivetrain are operable, disabled vehicles may also be towed as described under “recreational towing” in the “starting and operating” section. Towin...

  • Page 521

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members o...

  • Page 522

    Two-wheel drive models the manufacturer recommends towing your vehicle with all four wheels off the ground using a flatbed. If flatbed equipment is not available, and the transmis- sion is operable, the vehicle may be towed (with rear wheels on the ground) with the transmission in neu- tral . Speed ...

  • Page 523

    Caution! • front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when towing. • failure to follow these towing methods could result in damage to the transmission and/or trans- fer case. Such damage is not c...

  • Page 525: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.7l . . . . . . . . . . . . . 526 䡵 engine compartment — 4.7l . . . . . . . . . . . . . 527 䡵 engine compartment — 5.7l . . . . . . . . . . . . . 528 䡵 onboard diagnostic system (obd ii) . . . . . . . 529 ▫ loose fuel filler cap message . . ....

  • Page 526

    ▫ windshield wiper blades . . . . . . . . . . . . . . . 540 ▫ adding washer fluid . . . . . . . . . . . . . . . . . 540 ▫ exhaust system . . . . . . . . . . . . . . . . . . . . . 541 ▫ cooling system . . . . . . . . . . . . . . . . . . . . . 544 ▫ brake system . . . . . . . . . . . . . . . . . . . ....

  • Page 527

    䡵 fluids, lubricants and genuine parts . . . . . . . 582 ▫ engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 582 ▫ chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . 583 7 maintaining your vehicle 525.

  • Page 528

    Engine compartment — 3.7l 1 — air cleaner filter 7 — washer fluid reservoir 2 — automatic transmission dipstick (if equipped) 8 — power steering fluid reservoir 3 — engine oil dipstick 9 — engine oil fill 4 — brake fluid reservoir 10 — coolant pressure cap 5 — battery 11 — engine coolant reservoir 6...

  • Page 529

    Engine compartment — 4.7l 1 — air cleaner filter 7 — washer fluid reservoir 2 — automatic transmission dipstick 8 — power steering fluid reservoir 3 — engine oil dipstick 9 — engine oil fill 4 — brake fluid reservoir 10 — coolant pressure cap 5 — battery 11 — engine coolant reservoir 6 — integrated ...

  • Page 530

    Engine compartment — 5.7l 1 — air cleaner filter 7 — washer fluid reservoir 2 — automatic transmission dipstick 8 — integrated power module (fuses) 3 — engine oil fill 9 — power steering fluid reservoir 4 — engine oil dipstick 10 — coolant pressure cap 5 — brake fluid reservoir 11 — engine coolant r...

  • Page 531

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 532

    The select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). Emissions inspection and maintenance programs in some l...

  • Page 533

    4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 534

    Your vehicle. Refer to these service manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehi...

  • Page 535

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 536

    Note: under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, whichever occurs first. Engine oil selection for best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are api certified...

  • Page 537

    Lubricants which do not have both the engine oil certi- fication mark and the correct sae viscosity grade num- ber should not be used. Note: for 2500/3500 trucks with a 5.7l engine oper- ating under a gross combined weight rating of 14,000 lbs (6 350 kg) or greater, sae 5w-30 engine oil is recom- me...

  • Page 538

    Engine air cleaner filter refer to the “maintenance schedule” for the proper maintenance intervals. Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unles...

  • Page 539

    Warning! (continued) • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories...

  • Page 540

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 541

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency (epa) and is an ozone-saving product. However, the manufacturer recommends that air condi- tioning service be performed by authorized dealers ...

  • Page 542

    Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the w...

  • Page 543

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed up, operate the defroster for a few minutes to reduce the possibility of smearing or freezi...

  • Page 544

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 545

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 546

    Cooling system warning! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Engine co...

  • Page 547

    Refer to the “maintenance schedule” for the proper maintenance intervals. Selection of coolant use only the manufacturer’s recommended engine cool- ant (antifreeze). Refer to “fluids, lubricants, and genu- ine parts” in “maintaining your vehicle” for further information. Caution! • mixing of engine ...

  • Page 548

    Adding coolant your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 104,000 miles (169 000 km) before replacement. To prevent reducing this extended mainte- nance period, ...

  • Page 549

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that the engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign...

  • Page 550

    Rules for your community. To prevent ingestion by ani- mals or children do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills i...

  • Page 551

    3. Check the coolant level on the dipstick. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing en- gine coolant (antifreeze). Advise your service attendant of this. As long as the eng...

  • Page 552

    • do not overfill the coolant recovery bottle. • check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing. • if frequent engine cool...

  • Page 553

    Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 554

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid ...

  • Page 555

    Warning! (continued) • do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Rear axle and 4x4 front driving axle fluid level for normal service, periodic fluid level c...

  • Page 556

    Limited-slip differentials this vehicle requires that 4 oz. (118 ml) mopar 威 limited slip additive or equivalent be added to the gear lubri- cant. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. The mopar 威 limited slip additive or equivalent s...

  • Page 557

    Caution! • do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the new vehicle limited warranty. • using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmissi...

  • Page 558

    Fluid level check – 42rle/545rfe check the fluid level while the transmission is at normal operating temperature 82°c (180°f). This occurs after at least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably be- tween the fingertips. To check the automatic...

  • Page 559

    Caution! Be aware that if the fluid temperature is below 50°f (10°c) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission afte...

  • Page 560

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road...

  • Page 561

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder which will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty ...

  • Page 562

    Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use mopar 威 wheel cleaner or equivalent or select a nonabrasive, non-acidic...

  • Page 563

    Mopar 威 total clean or equivalent is specifically recom- mended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a dam...

  • Page 564

    Cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rearview mirror, spray cleaner on the towel...

  • Page 565

    To help maintain the appearance of your spray-on bedliner, the manufacturer recommends you periodically rinse all loose dirt from your truck bed and clean your truck at least twice per year using the mopar 威 spray-on bedliner conditioner available at your local authorized dealer. To help maintain th...

  • Page 566

    To cover the metal exposed by the scratch is required. To repair a tear or gouge, follow the directions provided in the mopar 威 quick repair kit. Fuses totally integrated power module the totally integrated power module is located in the engine compartment near the battery. This center con- tains ca...

  • Page 567

    Cavity cartridge fuse mini fuse description j03 30 amp pink diesel powertrain control module – if equipped j04 25 amp natural driver door node j05 25 amp natural passenger door node j06 40 amp green antilock brakes pump/stability control system j07 30 amp pink antilock brakes valve/stability control...

  • Page 568

    Cavity cartridge fuse mini fuse description j21 20 amp blue front washer con- trol j22 25 amp natural sunroof module m1 15 amp blue stop switch lamp m5 25 amp natural 115v ac inverter m6 20 amp yellow power outlet #1 (cigar lighter)/ rain snsr m7 20 amp yellow power outlet #2 m8 20 amp yellow front ...

  • Page 569

    Cavity cartridge fuse mini fuse description m14 20 amp yellow back up camera (domestic only) m15 20 amp yellow power seat module(s)/audio telematics/daytime running lights relay/instrument cluster/transfer case module m16 10 amp red airbag module m19 25 amp natural automatic shut- down 1 and 2 m20 1...

  • Page 570

    Cavity cartridge fuse mini fuse description m30 15 amp blue j1962 diag connec- tor m32 10 amp red airbag module m33 10 amp red powertrain control module m34 10 amp red park assist module/climate control system module/ir sensor/ compass module m35 15 amp blue left front & rear parklamps m36 20 amp ye...

  • Page 571

    Caution! (continued) • when replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem i...

  • Page 572

    (or check to see if the fuse is blown) to ensure that it is fully seated. When the iod fuse is extracted, the instrument cluster in the odometer window will dis- play ⬙no fuse.” replacement bulbs light bulbs – interior bulb no. Overhead console lamps . . . . . . . . . . . . . . . Ts 212-2 dome lamp ...

  • Page 573

    Bulb replacement dual or quad headlamp/front park and turn signal — if equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the four plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges. 4. Remove the two pla...

  • Page 574

    8. Reach through the access hole of the wheel house splash shield and lift the slide lock upward far enough to disengage it from the lock post on the back of the front lamp unit housing. 9. Remove the headlamp assembly. Grasp the outboard edge of the lamp and pull it straight forward to disen- gage ...

  • Page 575

    Fog lamps 1. Reach under and behind the front bumper to access the back of the front fog lamp housing. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise 1 ⁄ 4 turn to unlock the bulb from the housing. 4. Pull the bulb straight out from th...

  • Page 576

    2. Pull the outboard side of the lamp rearward far enough to unsnap the two receptacles on the outboard side of the lamp housing from the two plastic snap post retainers in the outer box side panel. 3. Disconnect the wiring harness connectors from the bulb socket. 4. Rotate the bulb socket countercl...

  • Page 577

    Center high-mounted stoplamp (chmsl) with cargo lamp 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn the desired bulb socket 1 ⁄ 4 turn and remove the socket and bulb from housing. 7 maint...

  • Page 578

    4. Pull the desired bulb straight from the socket. Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • outside bulbs: cargo lamps • inside bulb: center high-mounted stop lamp 5. Reverse the p...

  • Page 579

    2. Rotate the socket 1 ⁄ 4 turn and pull it from the lamp assembly. 3. Pull the bulb straight from it’s socket and replace. 7 maintaining your vehicle 577.

  • Page 580

    Rear lamp bar id marker (dual rear wheels) — if equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets. 2. Turn the socket 1 ⁄ 4 turn counterclockwise to access the bulb. 3. Pull the bulb straight out from the socket. 4. Reverse the procedure for installation of the bul...

  • Page 581

    Side marker lamps (dual rear wheels) — if equipped 1. Push rearward on the side marker lamp assembly. 2. Pull the entire assembly from the fender. 3. Turn the socket 1 ⁄ 4 turn counterclockwise and remove from assembly to access the bulb. 4. Pull the bulb straight out from socket. 5. Reverse the pro...

  • Page 582

    Fluid capacities u.S. Metric fuel (approximate) 1500 regular cab shortbed/crew quad cab models 26 gallons 98 liters 1500 regular cab longbed/crew quad cab models (optional) 32 gallons 121 liters 2500/3500 shortbed models 34 gallons 129 liters 2500/3500 longbed models 35 gallons 132 liters engine oil...

  • Page 583

    U.S. Metric cooling system 3.7l engine (mopar 威 antifreeze/coolant 5 year/100,000 mile formula or equivalent) 14 quarts 13 liters 4.7l engine (mopar 威 antifreeze/coolant 5 year/100,000 mile formula or equivalent) 14 quarts 13 liters 5.7l engine — 1500 models (mopar 威 antifreeze/coolant 5 year/100,00...

  • Page 584

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) or equivalent. Engine oil use api certified sae 5w-20 engine oil, meeting the requirements of chrysl...

  • Page 585

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Transfer case mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Transfer case – bw44–44 only mopar 威 bw44–4...

  • Page 587: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 586 ▫ required maintenance intervals . . . . . . . . . . 588 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 588

    Maintenance schedule the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating condition...

  • Page 589

    Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “electronic vehicle information center...

  • Page 590

    Caution! Failure to perform the required maintenance items may result in damage to the vehicle. Required maintenance intervals note: ** vehicles built with the 4.7l engine are equipped with sixteen spark plugs. One set is located on the top of the engine under the coils and the second set is located...

  • Page 591

    8,000 miles (13,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only). Odomet...

  • Page 592

    24,000 miles (39,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ i...

  • Page 593

    40,000 miles (65,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only). Odo...

  • Page 594

    56,000 miles (91,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only). Odo...

  • Page 595

    64,000 miles (104,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). ❏ replace the engine air cleaner filter. ❏ replace the ignition cable...

  • Page 596

    72,000 miles (117,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏...

  • Page 597

    88,000 miles (143,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only). O...

  • Page 598

    96,000 miles (156,000 km) or 72 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏ replace the engine air cleaner filter. ❏ replace the ignition cable...

  • Page 599

    104,000 miles (169,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only)....

  • Page 600

    120,000 miles (195,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏ lube the front drive shaft fitting (2500/3500 (4x4) models only)....

  • Page 601

    128,000 miles (208,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). ❏ replace the engine air cleaner filter. ❏ replace the ignition cab...

  • Page 602

    144,000 miles (234,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). ❏ if using your vehicle for any of the following: dusty or off-roa...

  • Page 603

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about...

  • Page 605: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605 ▫ prepare for the appointment . . . . . . . . . . . 605 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 605 ▫ be reasonable with r...

  • Page 606

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 611 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 611 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 611 ▫ temperature grades . . . . . . . . . . . . . . . . . . 61...

  • Page 607

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 608

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 609

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 610

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 611

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 612

    • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, and/or...

  • Page 613

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 614

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 615: Index

    Index 10

  • Page 616

    Adding engine coolant (antifreeze) . . . . . . . . . . 546 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 452 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . 133 air cleaner, engine (engine air cleaner filter) . . . 536 air conditioner maintenance . . . . . . . . ....

  • Page 617

    Fluid and filter changes . . . . . . . . . . . . . . . 557 fluid level check . . . . . . . . . . . . . . 554,555,556 fluid type . . . . . . . . . . . . . . . . . . . . . . 554,583 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . 314 shifting . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 618

    Caps, filler oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . 534 power steering . . . . . . . . . . . . . . . . . . . . . . 391 radiator (coolant pressure) . . . . . . . . . . . . . 547 car washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558 carbon monoxide warning . . . ...

  • Page 619

    Coolant pressure cap (radiator cap) . . . . . . . . . . 547 cooling system . . . . . . . . . . . . . . . . . . . . . . . . . 544 adding coolant (antifreeze) . . . . . . . . . . . . . 546 coolant capacity . . . . . . . . . . . . . . . . . . . . . 580 coolant level . . . . . . . . . . . . . . . . . . ...

  • Page 620

    Dual rear wheels . . . . . . . . . . . . . . . . . . . . . 429,507 dvd player (video entertainment system™) . . . . 286 e-85 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448 electric rear window defrost . . . . . . . . . . . . . . . 180 electrical power outlets . . . . . . . . . . ...

  • Page 621

    Oil selection . . . . . . . . . . . . . . . . . . . . . 534,580 oil synthetic . . . . . . . . . . . . . . . . . . . . . . . . 535 temperature gauge . . . . . . . . . . . . . . . . . . . 210 enhanced accident response feature . . . . . . . . . . 63 entry system, illuminated . . . . . . . . . . . . . ...

  • Page 622

    Four-way hazard flasher . . . . . . . . . . . . . . . . . . 491 freeing a stuck vehicle . . . . . . . . . . . . . . . . . . . 514 front axle (differential) . . . . . . . . . . . . . . . . . . . 553 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 adding . . . . . . . . . . ...

  • Page 623

    Gross axle weight rating . . . . . . . . . . . . . . . . . . 457 gross vehicle weight rating . . . . . . . . . . . . . . . . 456 guide, body builders . . . . . . . . . . . . . . . . . . . . . . 6 gvwr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454 hands-free phone (uconnect™) . . ...

  • Page 624

    Information center, vehicle . . . . . . . . . . . . . . . . . 227 inside rearview mirror . . . . . . . . . . . . . . . . . . . . 93 instrument cluster . . . . . . . . . . . . . . . . . 206,208,210 instrument panel and controls . . . . . . . . . . . . . . 205 instrument panel lens cleaning . . . . . ...

  • Page 625

    Brake assist warning . . . . . . . . . . . . . . . . . . 403 brake warning . . . . . . . . . . . . . . . . . . . . . . 219 bulb replacement . . . . . . . . . . . . . . . . . 570,571 cap top clearance . . . . . . . . . . . . . . . . . . . 576 cargo . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 626

    Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 automatic door . . . . . . . . . . . . . . . . . . . . . . 30 child protection . . . . . . . . . . . . . . . . . . . . . . 33 door . . . . . . . . . . . . ...

  • Page 627

    Navigation system (uconnect™ gps) . . . . . . . . . . 147 new vehicle break-in period . . . . . . . . . . . . . . . . 81 occupant restraints . . . . . . . . . . . . . . . . . . . 38,59,63 occupant restraints (sedan) . . . . . . . . . . . . . 56,59,62 octane rating, gasoline (fuel) . . . . . . . . . ...

  • Page 628

    Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . 392 passing light . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 pedals, adjustable . . . . . . . . . . . . . . . . . . . . . . . 133 personal settings . . . . . . . . . . . . . . . . . . . . . . . . 242 pets . . . . . . . ...

  • Page 629

    Reclining rear seats . . . . . . . . . . . . . . . . . . . . . . 110 recorder, event data . . . . . . . . . . . . . . . . . . . . . . 66 recreational towing . . . . . . . . . . . . . . . . . . . . . . 478 shifting into transfer case neutral(n) . . . 481,483 shifting out of transfer case neutral (n) ...

  • Page 630

    Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 front seat . . . . . . . . . . . . . . . . . . . . . . . . . . 39 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 83 pretensioners . . . . . . . . . . . . . . . . . . . . . . . . 50 reminder . . . . . . . . . . . . . . ...

  • Page 631

    Sliding rear window power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 snow chains (tire chains) . . . . . . . . . . . . . . . . . 425 snow plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474 snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427 spare tir...

  • Page 632

    Tip start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 tire and loading information placard . . . . . . 411,424 tire identification number (tin) . . . . . . . . . . . . . 409 tire markings . . . . . . . . . . . . . . . . . . . . . . . . . . 406 tire safety information . . . . . . ...

  • Page 633

    Trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . 456 cooling system tips . . . . . . . . . . . . . . . . . . 473 hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460 minimum requirements . . . . . . . . . . . . . . . . 463 mirrors . . . . . . . . . . . . . . . . . . ...

  • Page 634

    Vehicle loading . . . . . . . . . . . . . . . . . . . . . . 412,453 vehicle modifications/alterations . . . . . . . . . . . . . . 7 vehicle storage . . . . . . . . . . . . . . . . . . . . . . . 301,569 video entertainment system™ (rear seat video system) . . . . . . . . . . . . . . . . . . 286 voice...

  • Page 635

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 636

    Seventh edition printed in u.S.A. Chrysler group llc.