1. DL manuals
  2. RAM
  3. Amplifier
  4. V-12000
  5. Operation Manual

RAM V-12000 Operation Manual

Summary of V-12000

  • Page 1

    Operation manual notice d’emploi bedienungsanleitung p-6546-564 qxpdqxdoc 4/11 © 2011 by c.E. Studio-2 s.L. - spain (eec) http://www.Ramaudio.Com e-mail: support@ramaudio.Com professional power amplifiers v series 6000-9000-12000 9004-9044-12004-12044.

  • Page 2: Caution

    Warning: to avoid fire or electrocution risk do not expose the unit to rain or moisture. To avoid electric shock, do not open the unit. No user serviciable parts inside. In the case of disfunction, have the unit checked by qualified agents. Class i device. Important: clean the front panel filters re...

  • Page 3

    0 safety precautions 1 general information 1.1 introduction 1.2 main characteristics 2 controls: where and what? 2.1 front panel 2.2 rear panel 3 installation and operation 3.1 connections 3.1.1 dual channel mode 3.1.2 link channel mode 3.1.3 bridge channel mode 3.2 configuration 3.3 troubleshooting...

  • Page 4

    The v series devices feature two or four channel models, ready for rough han- dling in the touring world. For this pur- pose, v series amps implement over- sized high efficiency regulated power supply with pfc front end to deliver their full performances independently of mains status. This together ...

  • Page 5

    Lokalisierung der funktionen see figure configuration and signal attenua- tion level control knobs: permit independent control of each chan- nel’s attenuation and change the amplifier configuration. See page 10. Signal: this led indicates pres- ence of signal at the inputs. Temp: this led shows temp...

  • Page 6

    See figure signal input: female neutrik ® xlr connectors for the amplifier’s signal input. Signal link: male neutrik ® xlr connectors for daisy chaining input signal to other amplifiers (parallel connected to female input connec- tors). Speaker connectors: neutrik ® speakon to connect the speakers. ...

  • Page 7

    The power switch must always be on the “off” position before plugging the amp to a properly earthed mains sock- et (170-265v ac). The colour code is: blue: neutral brown: live, single phase yellow-green: protective earth the input signal fed to the amplifier can be either balanced or un-balanced. Th...

  • Page 8

    Installation and operation installation et mise en service the amplifier can operate on three dif- ferent configurations: dual, link or bridge. The connections for the three modes are different. See figure - set the amplifier mode to “dual”. - select the chosen gain (default set- ting 32db). - conne...

  • Page 9

    3 4 dual channel 2 ch models 2 ch models 8 5 link inputs bridge mode 2 ch models.

  • Page 10

    3 4 dual channel 4 channel models 4 channel models 4 channel models 5 link inputs bridge mode bridge + dual mode 3 channels mode 9.

  • Page 11

    Amplifier setup installation and operation 1-g32db-dual-unlink m 0db 0db -3db -6db operating time 45h 34min firmware version amp control v1.2b channel temperature 60% 50% 60% 70% display mode vu meter 10 main screen: shows the current preset name (“g32db- dual-unlink” as default), and the channel at...

  • Page 12

    Amplifier setup: when you are in the main menu and access to the amplifier setup section, you can change different amplifier parameters, change the current preset and protect the access using a password. The menu development for this section is the next: amplifier gain [db] 32db 32db 32db 32db ampli...

  • Page 13

    In the event of incorrect connection or misfunctioning, the amp will activate one or more of its led to warn about the problem. Correct function: sgnl lights to indi- cate signal presence. Icl: the intelligent clip limiter is ope- rating (see page 10). No signal: no input signal is reaching the amp....

  • Page 14

    This is a complete set of protections that monitors the main amp parameters (load status, signal input, temperature, current, etc.) in order to draw from the power sup- ply only the precise amount of current required to maintain safe operation during hazardous or extreme working conditions. This sys...

  • Page 15

    4.2 data 4.2 données techniques 4.2 technische daten technical specifications spécifications technische spezifikationen 14 technical specifications v-6000 v-9000 v-12000 v-9004 v-9044 v-12004 v-12044 output power 1khz, 1.0% thd+n @ 2 Ω 2x 3025 w 2x 4400 w 2x 5900 w 4x 2260 w - 4x 3025 w - @ 4 Ω 2x 1...

  • Page 16

    Manufactured in the eec by c.E. Studio-2 s.L. Pol. Ind. La figuera - c/rosa de luxemburgo, nº 34 46970 alaquas - valencia - spain phone: +34 96 127 30 54 fax: +34 96 127 30 56 http://www.Ramaudio.Com e-mail: support@ramaudio.Com.