Operation manual notice d’emploi bedienungsanleitung p-6653-175 qxpdqxdoc 7/14 © 2014 by c.E. Studio-2 s.L. - spain (eec) http://www.Ramaudio.Com e-mail: support@ramaudio.Com professional power amplifiers zetta series 210-215-220-236 420-430-440
Safety precautions avertissements sicherheitshinweise 1 warning: the exclamation point inside an equilateral triangle indicates the existen- ce of internal components whose substi- tution may affect safety. The lightning and arrowhead symbol warns about the presence of uninsula- ted dangerous voltag...
0 safety precautions 1 general information 1.1 introduction 1.2 main characteristics 2 controls: where and what? 2.1 front panel 2.2 rear panel 3 installation and operation 3.1 connections 3.1.1 dual channel mode 3.1.2 bridge channel mode 3.2 troubleshooting 4 technical specifications 4.1 protection...
The zetta series, is the result of an in depth study, in order to reach the best compromise between economy and performances, taking advantage of lat- est improvements in automated mixed surface mount and through hole elec- tronic assembly. Zetta series are a project based on an up-side-down mono-bl...
Lokalisierung der funktionen controls: where and what? Commandes et fonctions 4 1 1 2 3 3 see figure signal attenuation level control knobs: permit independent control of each channel’s attenuation (21 steps). Signal: this led indicates pre- sence of signal at the inputs. Pms : led indicating pms in...
See figure signal input: female neutrik ® xlr connectors for the amplifier’s signal input. Speaker connectors: neutrik ® speakon to connect the speakers. Dual / bridge operation selection switch. To control the level in bridge mode use the ch-a level knob. Mains power cord: to connect the amplifier ...
The power switch must always be on the “off” position before plugging the amp to a properly earthed mains sock- et (170-265v ac). The colour code is: blue: neutral brown: live, single phase yellow-green: protective earth the input signal fed to the amplifier can be either balanced or un-balanced. Th...
Installation and operation installation et mise en service the amplifier can operate on two differ- ent configurations: dual, or bridge. The connections for the two modes are different. See figure - set the amplifier mode to “dual”. - connect the signal lines to the female xlr connectors on all chan...
3 dual channel 2 ch models 8 4 bridge mode 2 ch models.
3 dual channel 4 channel models 4 channel models 4 bridge mode bridge + dual mode 3 channels mode 9.
In the event of incorrect connection or misfunctioning, the amp will activate one or more of its led to warn about the problem. Correct function: sgnl lights to indi- cate signal presence. Icl: the intelligent clip limiter is ope- rating (see page 10). No signal: no input signal is reaching the amp....
This is a complete set of protections that monitors the main amp parameters (load status, signal input, temperature, current, etc.) in order to draw from the power sup- ply only the precise amount of current required to maintain safe operation during hazardous or extreme working conditions. This sys...
4.2 data 4.2 données techniques 4.2 technische daten technical specifications spécifications technische spezifikationen 12 technical specifications z-210 z-215 z-220 z-236 z-420 z-430 z-440 max. Output power @ 2 Ω 2x 500 w 2x 750 w 2x 1000 w 2x 1800 w 4x 500 w 4x 750 w 4x 1000 w @ 4 Ω 2x 400 w 2x 70...
Manufactured in the eec by c.E. Studio-2 s.L. Pol. Ind. La figuera - c/rosa de luxemburgo, nº 34 46970 alaquas - valencia - spain phone: +34 96 127 30 54 fax: +34 96 127 30 56 http://www.Ramaudio.Com e-mail: support@ramaudio.Com.