Part #16941 manual printed in taiwan rev. 02/10 rd v01 par t # 169 41 manual impreso en t aiw an rev . 02/10 rd v01 this tool is for use only by licensed operators. You must obtain a license before using it. A tool operator's card will be issued to you after successfully completing the enclosed exam...
2 safety introduction danger danger safety introduction this tool is to be used only by properly trained and licensed operators. You must successfully complete the ramset training program for the tool and obtain a certified operator's license before handling, loading, or operating this tool. Safety ...
Safety instructions safety instructions 3 preparation acceptable base materials powder-actuated fastening is suitable for use in the following base materials only: • pouredconcrete • structuralsteel • masonryjoints(seepage8) never attempt to fasten into any other type of material. Fastening into oth...
Safety instructions safety instructions 4 loads and load selection safety 1. Always make a test fastening after being sure that the base material is suitable for powder actuated fastening. Failure to determine the correct power level to be used may result in the use of excessive power, allowing the ...
5 safety instructions safety instructions tool handling safety 1. Always be sure tool is operating properly before attempting to use it. Follow the “daily function check” shown to the right and described on page 9. 2. Always load tool using a strip load selected directly from a box indicating the po...
6 el no seg uir las instrucciones puede ocasionar lesiones al operador de la herramienta o a terceras personas seguridad en la aplicación de elementos de fijación 1. U tili ce úni cam ent e la he rra mie nta par a fi jar so bre un m ate ria l b ase ade cua do. 2. N unc a d isp are la he rra mie nta ...
Fasteners / loads fasteners / loads 7 your ramset cobra + tool uses only the ramset fasteners and loads shown below or listed for the tool in the product catalog. Danger never use any other types of fasteners or strip loads in the ramset cobra + tool. Use of other types of fasteners or loads may cau...
Fastening applications fastening applications 8 fastening applications your ramset tool can be used for a wide range of fastening needs in a variety of base materials. Reading and following these important fastening guidelines will help you get the best results from your tool, fasteners, and powder ...
Tool operating instructions tool operating instructions 9 tool operation daily function test always check the tool first to make sure it does not contain a strip load or fastener. Test the tool several times by depressing the muzzle bushing fully on a hard surface and pulling the trigger. You should...
4. Hold the tool perpendicular (90˚) to the work surface with both hands, and press down firmly to fully depress the tool. Maintain firm downward pressure on the tool with both hands and pull the trigger to drive the fastener. Do not depress the tool against anything other than the intended work sur...
11 troubleshooting troubleshooting refer to parts schematic for proper assembly of parts – overdriving of fasteners – excessive power – turn power adjust wheel down – change to next lower power level load strip – tool fails to fire – failure to index strip – strip not inserted in tool correctly or i...
Parts schematic parts schematic 12 diag rama de piezas diag rama de piezas 12.
Parts list / maintenance parts list / maintenance 13 cobra + tool parts list key part no. Description 1 sc301500 spall guard 2 sc385009 front barrel (baseplate) 3 sc301011a shear clip (pkg. Of 3) 4 sc305010 fastener guide 5 sc385903 piston assembly 6 sc301208 piston ring 7 sc302012 pawl (stop) 8 sc3...
14 1. Rotate the barrel retention clip off of the pawl using a flat blade screwdriver or the point of a long fastener. Rotate the barrel retention clip away from pawl remove the pawl 2. Remove the pawl by lifting it up and away from the tool body. Remove the barrel assembly 3. Slide the front barrel...
15 disassembly disassembly 6. Slide the piston out of the rear barrel assembly and slide the guide out of the front barrel. The tool is now disassembled for normal cleaning. Inspect all parts for wear or damage and clean or replace as required. Use detergent oil and cleaning brushes to remove dirt a...
Warranty all warranties of the products described herein, expressed or implied, including the warranty of merchantability and fitness for particular purposes are specifically excluded, except for the following: itw brands will repair or replace at its sole option any tool part or fastener which with...
After studying and understanding the material in this tool manual, answer the following questions. Complete the information on the other side of this page. Enclose a copy of your sales receipt and send to the address on the back of this manual to activate your tool warranty and receive your tool lic...
El c obr a + es tá gar ant iza do por 1 año de spu és de ven ta por it w b ran ds. Dec lar o q ue he leí do y c om pre ndi do el m anu al d e in stru cci one s y en tre nam ien to del ope rad or d e la h err am ien ta cob ra + y he con tes tad o e l e xam en del o per ado r q ue apa rec e a l re ver...
