- DL manuals
- RAMSET
- Tools
- R150
- Operator's safety & operating instruction manual
RAMSET R150 Operator's safety & operating instruction manual
Summary of R150
Page 1
Ramset r150 tool operator’s safety & operating instruction manual danger read and obey all safety and operating instructions before operating tool. Gas powered, low velocity piston type fastening tool.
Page 2: Safety Introduction
Just as no one can merely read a book about driving an automobile and then hope to drive one safely, no one should attempt to use the r150 gas powered tool without adequate, competent personal instruction. No automobile instruction book or instructor can forewarn a learner against all possibilities ...
Page 3: Preparation For Fastening
Preparation for fastening acceptable base materials the gas powered r150 tool is suitable for use in the following base materials only: • poured concrete • structural steel • concrete block and horizontal joints in brick or masonry walls never attempt to fasten into any other type of material. Faste...
Page 4: Fuel Cells and Batteries
Fuel cells and batteries fuel cells • the fuel cell must be used at temperatures between -5° c (23° f) and 49° c (120° f). • at the beginning of each fastening cycle, a measured amount of gas is injected into the combustion chamber. • the fuel cell is designed with an internal reservoir that is unde...
Page 5: Installing The Battery
Installing the battery • insert the battery into the tool as shown on the right with the clip toward the rear. • note the led light on the right side of the handle. After installing the battery: - if the light flashes green the tool is powered. - if the light flashes red the battery requires chargin...
Page 6: Safety Instructions
Safety instructions danger safety instructions danger 6 failure to follow instructions can cause injury to the tool operator or to bystanders. • use the tool only in well ventilated areas. • always hold the tool at right angles to the work surface. • never attempt to make a fastening at an angle to ...
Page 7: Fastening Applications
Fastening applications fastening applications 7 fastening applications your r150 tool can be used for a wide range of fastening needs in a variety of base materials. Reading and following these important fastening guidelines will help you get the best results from your tool and fasteners, as well as...
Page 8: Tool Operating Instructions
Tool operating instructions tool operating instructions 8 tool operation always check the tool first to make sure that it does not contain a fastener. If the tool contains a fastener from a previous application, remove both the battery and the fuel cell before attempting to remove the fastener. Oper...
Page 9: Quick Change Nose
Quick change nose the r150 tool is equipped with a quick change nose. This feature allows the user to change the work contact element to meet various fastening needs. The work contact element can be changed without the use of tools by following these steps: removal 1. Remove battery from the tool !!...
Page 10: Parts Schematic
Parts schematic 10 parts schematic r150 tool schematic.
Page 11: Parts Schematic
R150 tool schematic (continued) parts schematic 11 parts schematic.
Page 12: Parts List
Ramset r150 tool parts lists key part number description 1 336920 grill cap 2 336900 air filter 3 b0060a cap screws m5-30 w/washer (pkg of 4) 4 339000 cap assembly 5 b0070 spark plug wire 6 b0061a pc board screws, m4-12 (pkg of 3) 7 b0040 pc board 8 7505164 spark plug assembly 9 900525a fan motor as...
Page 13: Parts List
Parts list 13 parts list ramset r150 tool parts lists (continued) key part number description 32 339050 gas duct assembly 33 b0037a chamber springs (pkg of 2) 34 339060m sleeve/nose assembly 35 b0105 security stop 37 334020 battery support 38 337440 rubber handle, grip 39 333380 knob assembly 40 404...
Page 14: Servicing/troubleshooting
Filters and battery contacts cleaning the filters and battery contacts on a regular basis will help make your tool work more efficiently. To clean the filters • remove the cover and the filters. • lightly tap the filters to remove any dust. • replace the filters if damaged. • replace the filters and...
Page 15: Warranty
Itw ramset/red head warranty that new r150 power fastening tools, parts and accessories will be free from defects in material and workmanship for the period shown below, after the date of delivery to the original user. Two-year warranty a two-year warranty will apply to all parts, except those liste...
Page 16
For tool repair service contact your local authorized itw ramset/red head distributor or contact your nearest ramset tool repair center west midwest east los angeles, ca paris, ky allentown, pa 5950 boxford 7000 bypass road 739 roble road commerce, ca 90040 paris, ky 40361 allentown,pa 18109 phone: ...